This patch fixes missing includes from a number of .c files because
the code (wrongfully) depended on prom.h including them. The include
of linux/of_address.h was removed in microblaze prom.h in commit
"of/address: Clean up function declarations" (sha1 id 22ae782f8), but
not fixed in some callers. This patch fixes them up.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Tested-by: Michal Simek <monstr@monstr.eu>
The only tricky bit is the compat version of fanotify_mark, which
which on 32-bit the 64-bit mark argument is passed in as "high32",
"low32".
Signed-off-by: David S. Miller <davem@davemloft.net>
According to commit 22eeef4bb2
kgdb,arm: Individual register get/set for arm
It's now replaced by DBG_MAX_REG_NUM.
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
breakinfo->pev is a pointer to percpu pointer but was missing __percpu markup.
Add it.
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Commit dbbdee9473 removed
of_irq_pci_swizzle but didn't use pci_swizzle_interrupt_pin
instead.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
If a video head and keyboard are hooked up, specifying "console=ttyS0"
or similar to use a serial console will not work properly.
The key issue is that we must register all serial console capable
devices with register_console(), otherwise the command line specified
device won't be found. The sun serial drivers would only register
themselves as console devices if the OpenFirmware specified console
device node matched. To fix this part we now unconditionally get
the serial console register by setting serial_drv->cons always.
Secondarily we must not add_preferred_console() using the firmware
provided console setting if the user gaven an override on the kernel
command line using "console=" The "primary framebuffer" matching
logic was always triggering o n openfirmware device node match, make
it not when a command line override was given.
Reported-by: Frans Pop <elendil@planet.nl>
Tested-by: Frans Pop <elendil@planet.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 5a5f561 (convert OMAP3 PRCM macros to the _SHIFT/_MASK suffixes)
mistakenly removed the check for PER when disabling the IO chain.
During idle, if the PER powerdomain transitions into a lower state
and CORE does not, the IO pad wakeups are not being disabled in
the idle path after they are enabled. This can happen with the
lower C-states when using CPUidle for example.
This patch ensures that the check for disabling IO wakeups also checks
for PER transitions, matching the check done to enable IO wakeups.
Found when debugging PM/CPUidle related problems reported by Ameya
Palande <ameya.palande@nokia.com>. Problems were triggered
particularily on boards with UART2 consoles (n900, Overo) since UART2
is in the PER powerdomain.
Tested on l-o master (omap3_defonfig + CONFIG_CPU_IDLE=y) as well
as with current PM branch. Boards tested: n900, Overo, omap3evm.
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Ameya Palande <ameya.palande@nokia.com>
Tested-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
[tony@atomide.com: updated description to clarify the transistion]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit ffb63e3402 changed
Kconfig to select support for omap2, 3 and 4 by default.
However, CONFIG_SMP won't currently work properly on
uniprocessor ARMs, or if support for earlier ARM cores
is selected in.
Fix this by updating omap_4430sdp_defconfig to not
select omap2 or 3 at this point.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Otherwise we get the following error when enabling CONFIG_SMP
for omap3_defconfig:
arch/arm/kernel/entry-armv.S: Assembler messages:
arch/arm/kernel/entry-armv.S:48: Error: bad instruction `test_for_ipi r0,r6,r5,lr'
arch/arm/kernel/entry-armv.S:48: Error: bad instruction `test_for_ltirq r0,r6,r5,lr'
arch/arm/kernel/entry-armv.S:48: Error: bad instruction `test_for_ipi r0,r6,r5,lr'
arch/arm/kernel/entry-armv.S:48: Error: bad instruction `test_for_ltirq r0,r6,r5,lr'
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Otherwise we get the following error with omap3_defconfig and CONFIG_SMP:
Error: selected processor does not support `sev'
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
cpu_is_omap3517() and cpu_is_omap3505() are the subgroups of cpu_is_omap34xx(),
so we should check cpu_is_omap3517() and cpu_is_omap3505() first, then check
cpu_is_omap34xx().
Otherwise, All AM35XX (Sitara) clocks do not get registered and device drivers
(ti_hecc, etc...) that depend on those clocks are failing to get the clock and
end up with non working device.
Signed-off-by: Stanley.Miao <stanley.miao@windriver.com>
Tested-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Wrong placement of break causes all revisions of 3630 to be
detected as 3630 es1.2, we need to break main loop if we have
an identified chip, default falls through as in the rest of the
switches in this function.
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Sanjeev Premi <premi@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Manjunath K <manjugk@ti.com>
Cc: Anand Gadiyar <gadiyar@ti.com>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
gcc-4.6: ACPI: fix unused but set variables in ACPI
ACPI thermal: make procfs I/F depend on CONFIG_ACPI_PROCFS
ACPI video: make procfs I/F depend on CONFIG_ACPI_PROCFS
ACPI processor: remove deprecated ACPI procfs I/F
ACPI power_resource: remove unused procfs I/F
ACPI: remove deprecated ACPI procfs I/F
ACPI: introduce drivers/acpi/sysfs.c
ACPI: introduce module parameter acpi.aml_debug_output
ACPI: introduce drivers/acpi/debugfs.c
ACPI, APEI, ERST debug support
ACPI, APEI, Manage GHES as platform devices
ACPI, APEI, Rename CPER and GHES severity constants
ACPI, APEI, Fix a typo of error path of apei_resources_request
ACPI / ACPICA: Fix reference counting problems with GPE handlers
ACPI: Add the check of ADR flag in course of finding ACPI handle for PCI device
ACPI / Sleep: Drop acpi_suspend_finish()
ACPI / Sleep: Consolidate suspend and hibernation routines
ACPI / Wakeup: Simplify enabling of wakeup devices
ACPI / Sleep: Rework enabling wakeup devices
ACPI / Sleep: Free NVS copy if suspending of devices fails
Fixed up totally buggered "ACPI: fix unused but set variables in ACPI"
patch that doesn't even compile in the merge.
Thanks to Sedat Dilek <sedat.dilek@googlemail.com> for noticing the
breakage before I even pulled. And a big "Grrr.." at Len for not even
bothering to compile the tree before asking me to pull.
* git://git.infradead.org/mtd-2.6:
mtd/nand_ids: Fix buswidth
mtd/m25p80: fix test for end of loop
mtd/m25p80: retlen is never NULL
MIPS: Fix gen_nand probe structures contents
gen_nand: Test if nr_chips field is valid
BFIN: Fix gen_nand probe structures contents
nand/denali: move all hardware initialization work to denali_hw_init
nand/denali: Add a page check in denali_read_page & denali_read_page_raw
nand/denali: use cpu_relax() while waiting for hardware interrupt
nand/denali: change read_status function method
nand/denali: Fixed check patch warnings
ARM: Fix gen_nand probe structures contents
mtd/nand_base: fix kernel-doc warnings & typos
nand/denali: use dev_xx debug function to replace nand_dbg_print and some printk
nand/denali: Fixed handle ECC error bugs
nand/denali: use iowrite32() to replace denali_write32()
nand/denali: Fixed probe function bugs
* git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
arch/tile: don't validate CROSS_COMPILE needlessly
arch/tile: export only COMMAND_LINE_SIZE to userspace.
arch/tile: rename ARCH_KMALLOC_MINALIGN to ARCH_DMA_MINALIGN
arch/tile: Rename the hweight() implementations to __arch_hweight()
arch/tile: extend syscall ABI to set r1 on return as well.
arch/tile: Various cleanups.
arch/tile: support backtracing on TILE-Gx
arch/tile: Fix a couple of issues with the COMPAT code for TILE-Gx.
arch/tile: Use separate, better minsec values for clocksource and sched_clock.
arch/tile: correct a bug in freeing bootmem by VA for the optional second initrd.
arch: tile: mm: pgtable.c: Removed duplicated #include
arch: tile: kernel/proc.c Removed duplicated #include
Add fanotify syscalls to <asm-generic/unistd.h>.
arch/tile: support new kunmap_atomic() naming convention.
tile: remove unused ISA_DMA_THRESHOLD define
Conflicts in arch/tile/configs/tile_defconfig (pick the mainline version
with the reduced defconfig).
sys_accept4() was added in kernel 2.6.28, but ARM was not updated
to include it. The number and types of parameters is such that
no ARM-specific processing is needed, so wiring up sys_accept4()
just requires defining __NR_accept4 and adding a direct call in
the syscall entry table.
Tested with an EABI 2.6.35 kernel and Ulrich Drepper's original
accept4() test program, modified to define __NR_accept4 for ARM.
Using the updated unistd.h also eliminates a warning then building
glibc (2.10.2 and newer) about accept4() being unimplemented.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
With this change, the arch/tile Makefile will only check for a valid
combination of CROSS_COMPILE vs "uname -m" for a few common targets
that are typically the ones we get wrong (vmlinux, all, and modules).
The change handles the case of an empty "make" goal like "make all".
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
This fixes a failure in "make headers_check" for tile.
I hadn't realized this file was exported to userspace by default.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
fpu.state is allocated from task_xstate_cachep, the size of task_xstate_cachep
is xstate_size. xstate_size is set from cpuid instruction, which is often
smaller than sizeof(struct xsave_struct). kvm is using sizeof(struct xsave_struct)
to fill in/out fpu.state.xsave, as what we allocated for fpu.state is
xstate_size, kernel will write out of memory and caused poison/redzone/padding
overwritten warnings.
Signed-off-by: Xiaotian Feng <dfeng@redhat.com>
Reviewed-by: Sheng Yang <sheng@linux.intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Avi Kivity <avi@redhat.com>
Cc: Robert Richter <robert.richter@amd.com>
Cc: Sheng Yang <sheng@linux.intel.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Gleb Natapov <gleb@redhat.com>
Cc: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Commit d0679c7 restricted this workaround to powerpc only, but it turns
out that ARM needs it as well. Fixes
https://bugzilla.kernel.org/show_bug.cgi?id=16310 .
Reported-and-Tested-by: Robert Nelson <robertcnelson@gmail.com>
Acked-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Michal Marek <mmarek@suse.cz>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'for-linus/samsung-2635' of git://git.fluff.org/bjdooks/linux:
DMAENGINE: correct PL080 register header file
ARM: SAMSUNG: Fix on build warning about dependency in Kconfig
ARM: SMDK6410: Make virtual screen twice depth of real
ARM: S3C64XX: Update consistent DMA size to 8MiB
ARM: S3C64XX: Add audio support to SmartQ
ARM: S3C64XX: Framebuffer fix for SmartQ5
ARM: S3C64XX: Set wifi and iNAND as permanently connected SD devices on SmartQ boards
ARM: S3C64XX: Move SmartQ LCD control platform definition to shared file
ARM: mach-real6410: add sdhc device support
ARM: mach-real6410: add dm9000 ethernet support for mach-real6410
ARM: S3C64XX: Support for Real6410
Fix up trivial conflicts in arch/arm/mach-s3c64xx/mach-smartq5.c
("remove pixclock" vs "Framebuffer fix for SmartQ5")
* 'for-linus/i2c-2636' of git://git.fluff.org/bjdooks/linux:
i2c/nuc900: add i2c driver support for nuc900
i2c: Enable NXP LPC support in Kconfig
i2c-pxa: fix compiler warning, due to missing const
i2c: davinci: bus recovery procedure to clear the bus
i2c: davinci: Add cpufreq support
i2c: davinci: Add suspend/resume support
i2c: davinci: Add helper functions for power management
i2c: davinci: misc. cleanups: remove MOD_REG_BIT and IO_ADDRESS usage
i2c: davinci: Fix smbus Oops with AIC33 usage
This PL008 among all other variables named PL080 doesn't seem
right. Fix it. Also add some missing defined that I use in the
new PL08x driver.
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
For situations where double buffering is needed (such as the
current Android) make the screen virtual y size twice the
LCD size so that there is space for a second screen that
can be switched to.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Change the area available for consitent DMA allocations from the
default to 8MiB to allow drivers such as the framebuffer to get
more memory (for situations where larger virtual screen resolutions
are needed).
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This adds the I²C board information for the WM8987 used in the SmartQ as audio
codec and adds the I²C/I²S platform drivers.
Signed-off-by: Maurus Cuelenaere <mcuelenaere@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The following change makes the framebuffer work on SmartQ5. There are
still some problems with ADC, so this patch alone won't make the device
run (or even give a working fb), but it's one issue less to think about.
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Signed-off-by: Maurus Cuelenaere <mcuelenaere@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch changes the platform data definitions of the wifi and iNAND chip on
the SmartQ 5 and 7 to indicate that they don't have a CD line available and are
thus hard-wired to the SDHCI data lines.
Signed-off-by: Maurus Cuelenaere <mcuelenaere@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This shares the common LCD control platform definition used in the SmartQ 5 and
7. This also corrects it as a GPIO bitbanged SPI device instead of an I²C one,
which was wrong.
Signed-off-by: Maurus Cuelenaere <mcuelenaere@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch is based on "[PATCH v2] Support for Real6410"
Signed-off-by: Darius Augulis <augulis.darius@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add support for CoreWind Real6410 board, based on Samsung s3c6410 processor.
Signed-off-by: Darius Augulis <augulis.darius@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
According to commit 22eeef4bb2
kgdb,arm: Individual register get/set for arm
It's now replaced by DBG_MAX_REG_NUM.
Cc: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Three new syscalls for 2.6.36: prlimit64, fanotify_init and
fanotify_mark. Wire up the ia64 syscall table for them.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Mark arguments to certain system calls as being const where they should be but
aren't. The list includes:
(*) The filename arguments of various stat syscalls, execve(), various utimes
syscalls and some mount syscalls.
(*) The filename arguments of some syscall helpers relating to the above.
(*) The buffer argument of various write syscalls.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
These have been broken (returning "int") since the dawn of
time. But there were no users that needed the whole value
until commit
424acaaeb3
rwsem: wake queued readers when writer blocks on active read lock
made this change:
- (rwsem_atomic_update(0, sem) & RWSEM_ACTIVE_MASK))
- /* Someone grabbed the sem already */
+ rwsem_atomic_update(0, sem) < RWSEM_WAITING_BIAS)
+ /* Someone grabbed the sem for write already */
RWSEM_ACTIVE_MASK is 0xffffffffL, so the old code only looked
at the low order 32-bits. The new code needs to see all 64 bits.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Until now, the tile architecture ABI for syscall return has just been
that r0 holds the return value, and an error is only signalled like it is
for kernel code, with a negative small number.
However, this means that in multiple places in userspace we end up writing
the same three-cycle idiom that tests for a small negative number for
error. It seems cleaner to instead move that code into the kernel, and
set r1 to hold zero on success or errno on failure; previously, r1 was
just zeroed on return from the kernel (to avoid leaking kernel state).
This way a single conditional branch after the syscall is sufficient
to test for the failure case. The number of cycles taken is the same,
but the error-checking code is in just one place, so total code size is
smaller, and random userspace syscall code is easier to understand.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (30 commits)
perf: Add back list_head data types
perf ui hist browser: Fixup key bindings
perf ui browser: Add ui_browser__show counterpart: __hide
perf annotate: Cycle thru sorted lines with samples
perf ui: Make SPACE work as PGDN in all browsers
perf annotate: Sort by hottest lines in the TUI
perf ui: Complete the breakdown of util/newt.c
perf ui: Move hists browser to util/ui/browsers/
perf symbols: Ignore mapping symbols on ARM
perf ui: Move map browser to util/ui/browsers/
perf ui: Move annotate browser to util/ui/browsers/
perf ui: Move ui_progress routines to separate file in util/ui/
perf ui: Move ui_helpline routines to separate file in util/ui/
perf ui: Shorten ui_browser member names
perf, x86: P4 PMU -- update nmi irq statistics and unmask lvt entry properly
perf ui: Start breaking down newt.c into multiple files
perf tui: Introduce list_head based generic ui_browser refresh routine
perf probe: Fix memory leaks in add_perf_probe_events
perf probe: Fix to copy the type for raw parameters
perf report: Speed up exit path
...
* 'x86-uv-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, UV: Initialize BAU MMRs only on hubs with cpus
x86, UV: Modularize BAU send and wait
x86, UV: BAU broadcast to the local hub
x86, UV: Correct BAU regular message type
x86, UV: Remove BAU check for stay-busy
x86, UV: Correct BAU discovery of hubs and sockets
x86, UV: Correct BAU software acknowledge
x86, UV: BAU structure rearranging
x86, UV: Shorten access to BAU statistics structure
x86, UV: Disable BAU on network congestion
x86, UV: BAU tunables into a debugfs file
x86, UV: Calculate BAU destination timeout
* 'x86/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, asm: Use a lower case name for the end macro in atomic64_386_32.S
x86, asm: Refactor atomic64_386_32.S to support old binutils and be cleaner
x86: Document __phys_reloc_hide() usage in __pa_symbol()
x86, apic: Map the local apic when parsing the MP table.
It's wrong for several reasons, but the most direct one is that the
fault may be for the stack accesses to set up a previous SIGBUS. When
we have a kernel exception, the kernel exception handler does all the
fixups, not some user-level signal handler.
Even apart from the nested SIGBUS issue, it's also wrong to give out
kernel fault addresses in the signal handler info block, or to send a
SIGBUS when a system call already returns EFAULT.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
acpi_perf_data is a percpu pointer but was missing __percpu markup.
Add it.
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Dave Jones <davej@redhat.com>
This change rolls up random cleanups not representing any actual bugs.
- Remove a stale CONFIG_ value from the default tile_defconfig
- Remove unused tns_atomic_xxx() family of methods from <asm/atomic.h>
- Optimize get_order() using Tile's "clz" instruction
- Fix a bad hypervisor upcall name (not currently used in Linux anyway)
- Use __copy_in_user_inatomic() name for consistency, and export it
- Export some additional hypervisor driver I/O upcalls and some homecache calls
- Remove the obfuscating MEMCPY_TEST_WH64 support code
- Other stray comment cleanups, #if 0 removal, etc.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
This functionality was stubbed out until recently. Now we support our
normal backtracing API on TILE-Gx as well as on TILE64/TILEPro.
This change includes a tweak to the instruction encoding caused by
adding addxli for compat mode.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
First, the siginfo preamble wasn't quite right; we need to indicate
that we are padding up to 4 ints of preamble for 64-bit code, and
then for compat mode we need to pad differently, using only 3 ints.
Second, the C ABI requires a save area of two registers, not two
pointers, since in compat mode we have 64-bit registers all of which
we need to save, even though we only have 32-bit VAs.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
We were using the same 5-sec minsec for the clocksource and sched_clock
that we were using for the clock_event_device. For the clock_event_device
that's exactly right since it has a short maximum countdown time.
But for sched_clock we want to avoid wraparound when converting from
ticks to nsec over a much longer window, so we force a shift of 10.
And for clocksource it seems dodgy to use a 5-sec minsec as well, so we
copy some other platforms and force a shift of 22.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Fix this warning:
arch/s390/appldata/appldata_net_sum.c: In function 'appldata_get_net_sum_data':
arch/s390/appldata/appldata_net_sum.c:89: warning: initialization from incompatible pointer type
which was introduced with be1f3c2c02
"net: Enable 64-bit net device statistics on 32-bit architectures"
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
commit 485d527686 "sys_personality: change
sys_personality() to accept "unsigned int" instead of u_long" changed
the syscall interface for sys_personality.
Just follow the common code change in our arch code to avoid confusion.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This replaces Version 1 of this patch, which broke the build when
CONFIG_KEXEC and CONFIG_CRASH_DUMP were configured off. In that case
the storage for the 'in_crash_kexec' flag was never built.
This version defines that flag as 0 if CONFIG_KEXEC is not set.
The patch is tested with all combinations of those two options.
Signed-off-by: Cliff Wickman <cpw@sgi.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
LKML-Reference: <E1OiZcw-0001Hb-2g@eag09.americas.sgi.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
* 'params' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus: (22 commits)
param: don't deref arg in __same_type() checks
param: update drivers/acpi/debug.c to new scheme
param: use module_param in drivers/message/fusion/mptbase.c
ide: use module_param_named rather than module_param_call
param: update drivers/char/ipmi/ipmi_watchdog.c to new scheme
param: lock if_sdio's lbs_helper_name and lbs_fw_name against sysfs changes.
param: lock myri10ge_fw_name against sysfs changes.
param: simple locking for sysfs-writable charp parameters
param: remove unnecessary writable charp
param: add kerneldoc to moduleparam.h
param: locking for kernel parameters
param: make param sections const.
param: use free hook for charp (fix leak of charp parameters)
param: add a free hook to kernel_param_ops.
param: silence .init.text references from param ops
Add param ops struct for hvc_iucv driver.
nfs: update for module_param_named API change
AppArmor: update for module_param_named API change
param: use ops in struct kernel_param, rather than get and set fns directly
param: move the EXPORT_SYMBOL to after the definitions.
...
The current computation, introduced with f12a15be63, of FSEC_PER_SEC using
the multiplication of (FSEC_PER_NSEC * NSEC_PER_SEC) is performed only
with 32bit integers on small machines, resulting in an overflow and a
*very* short intervals being programmed. An interrupt storm follows.
Note that we also have to specify FSEC_PER_SEC as being long long to
overcome the same limitations.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Ingo Molnar <mingo@elte.hu>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use no_printk() for disabled gdbstub debugging functions to maintain side
effect checking.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a dummy printk function for the maintenance of unused printks through gcc
format checking, and also so that side-effect checking is maintained too.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Don't try and #include <linux/slab.h> in lib/inflate.c from the bootloader code
as linux/slab.h hauls in function defs that aren't available in the bootloader
code and may also haul in conflicting functions.
To fix this, make the inclusion of linux/slab.h contingent on NO_INFLATE_MALLOC
as are the usages of kmalloc() and kfree().
In MN10300, this causes the following errors:
In file included from include/linux/string.h:21,
from include/linux/bitmap.h:8,
from include/linux/nodemask.h:93,
from include/linux/mmzone.h:16,
from include/linux/gfp.h:4,
from include/linux/slab.h:12,
from arch/mn10300/boot/compressed/../../../../lib/inflate.c:106,
from arch/mn10300/boot/compressed/misc.c:170:
/warthog/am33/linux-2.6-mn10300/arch/mn10300/include/asm/string.h:19: error: conflicting types for 'memset'
arch/mn10300/boot/compressed/misc.c:59: error: previous definition of 'memset' was here
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With the newer compilers, size_t and ssize_t are expected to be (un)signed int
rather than (un)signed long.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A change to the RTC routines in the MN10300 arch used set_rtc_mms() when it
meant set_rtc_mmss(). This results in an error due to a reference of an
undefined symbol.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
pcc_cpu_info is a percpu pointer but was missing __percpu markup.
Add it.
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Dave Jones <davej@redhat.com>
Some nice improvements were made to rwsem in commit:
424acaaeb3
rwsem: wake queued readers when writer blocks on active read lock
but this change overlooked that ia64 had defined RWSEM_WAITING_BIAS
as an unsigned value, while the new code required a signed value (as
it is in every other architecture).
This fix suggested by the original patch author: Michel Lespinasse.
Signed-off-by: Tony Luck <tony.luck@intel.com>
* 'stable/xen-swiotlb-0.8.6' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
x86: Detect whether we should use Xen SWIOTLB.
pci-swiotlb-xen: Add glue code to setup dma_ops utilizing xen_swiotlb_* functions.
swiotlb-xen: SWIOTLB library for Xen PV guest with PCI passthrough.
xen/mmu: inhibit vmap aliases rather than trying to clear them out
vmap: add flag to allow lazy unmap to be disabled at runtime
xen: Add xen_create_contiguous_region
xen: Rename the balloon lock
xen: Allow unprivileged Xen domains to create iomap pages
xen: use _PAGE_IOMAP in ioremap to do machine mappings
Fix up trivial conflicts (adding both xen swiotlb and xen pci platform
driver setup close to each other) in drivers/xen/{Kconfig,Makefile} and
include/xen/xen-ops.h
Use a lowercase name for the end macro, which somehow fixes a binutils 2.16
problem.
Signed-off-by: Luca Barbieri <luca@luca-barbieri.com>
LKML-Reference: <tip-30246557a06bb20618bed906a06d1e1e0faa8bb4@git.kernel.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
CRIS don't need any special mapping for io, but didn't define this,
meaning that all uses of io_remap_pfn_range lead to compile errors.
This fixes a compile error introduced in CRIS when drivers/mtd/mtdchar.c
mmap handling was changed in commit dd02b67d5e
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
This platform didn't properly fill nr_chips in gen_nand
registration and therefore depended on gen_nand bug fixed by commit
81cbb0b177 ("mtd: gen_nand: fix support for
multiple chips")
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
These two platforms didn't properly fill nr_chips in gen_nand
registration and therefore depended on gen_nand bug fixed by by commit
81cbb0b177 ("mtd: gen_nand: fix support for
multiple chips")
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The old code didn't work on binutils 2.12 because setting a symbol to
a register apparently requires a fairly recent version.
This commit refactors the code to use the C preprocessor instead, and
in the process makes the whole code a bit easier to understand.
The object code produced is unchanged as expected.
This fixes kernel bugzilla 16506.
Reported-by: Dieter Stussy <kd6lvw+software@kd6lvw.ampr.org>
Signed-off-by: Luca Barbieri <luca@luca-barbieri.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: <stable@kernel.org> 2.6.35
LKML-Reference: <tip-*@git.kernel.org>
These three platforms didn't properly fill nr_chips in gen_nand
registration and therefore depended on gen_nand bug fixed by commit
81cbb0b177 ("mtd: gen_nand: fix support for
multiple chips")
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
isofs: Fix lseek() to position beyond 4 GB
vfs: remove unused MNT_STRICTATIME
vfs: show unreachable paths in getcwd and proc
vfs: only add " (deleted)" where necessary
vfs: add prepend_path() helper
vfs: __d_path: dont prepend the name of the root dentry
ia64: perfmon: add d_dname method
vfs: add helpers to get root and pwd
cachefiles: use path_get instead of lone dget
fs/sysv/super.c: add support for non-PDP11 v7 filesystems
V7: Adjust sanity checks for some volumes
Add v7 alias
v9fs: fixup for inode_setattr being removed
Manual merge to take Al's version of the fs/sysv/super.c file: it merged
cleanly, but Al had removed an unnecessary header include, so his side
was better.
* 'ixp4xx' of git://git.kernel.org/pub/scm/linux/kernel/git/chris/linux-2.6:
IXP4xx: Fix LL debugging on little-endian CPU.
IXP4xx: Fix sparse warnings in I/O primitives.
IXP4xx: Make mdio_bus struct static in the Ethernet driver.
IXP4xx: Fix ixp4xx_crypto little-endian operation.
IXP4xx: Prevent HSS transmitter lockup by disabling FRaMe signals.
ixp4xx/vulcan: add PCI support
ixp4xx: base support for Arcom Vulcan
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (226 commits)
ARM: 6323/1: cam60: don't use __init for cam60_spi_{flash_platform_data,partitions}
ARM: 6324/1: cam60: move cam60_spi_devices to .init.data
ARM: 6322/1: imx/pca100: Fix name of spi platform data
ARM: 6321/1: fix syntax error in main Kconfig file
ARM: 6297/1: move U300 timer to dynamic clock lookup
ARM: 6296/1: clock U300 intcon and timer properly
ARM: 6295/1: fix U300 apb_pclk split
ARM: 6306/1: fix inverted MMC card detect in U300
ARM: 6299/1: errata: TLBIASIDIS and TLBIMVAIS operations can broadcast a faulty ASID
ARM: 6294/1: etm: do a dummy read from OSSRR during initialization
ARM: 6292/1: coresight: add ETM management registers
ARM: 6288/1: ftrace: document mcount formats
ARM: 6287/1: ftrace: clean up mcount assembly indentation
ARM: 6286/1: fix Thumb-2 decompressor broken by "Auto calculate ZRELADDR"
ARM: 6281/1: video/imxfb.c: allow usage without BACKLIGHT_CLASS_DEVICE
ARM: 6280/1: imx: Fix build failure when including <mach/gpio.h> without <linux/spinlock.h>
ARM: S5PV210: Fix on missing s3c-sdhci card detection method for hsmmc3
ARM: S5P: Fix on missing S5P_DEV_FIMC in plat-s5p/Kconfig
ARM: S5PV210: Override FIMC driver name on Aquila board
ARM: S5PC100: enable FIMC on SMDKC100
...
Fix up conflicts in arch/arm/mach-{s5pc100,s5pv210}/cpu.c due to
different subsystem 'setname' calls, and trivial port types in
include/linux/serial_core.h
To keep panic_timeout accuracy when running under a hypervisor, the
current implementation only spins on long time (1 second) calls to mdelay.
That brings a good effect, but the problem is the keyboard LEDs don't
blink at all on that situation.
This patch changes to call to panic_blink_enter() between every mdelay and
keeps blinking in spite of long spin timer mode.
The time to call to mdelay is now 100ms. Even this change will keep
panic_timeout accuracy enough when running under a hypervisor.
Signed-off-by: TAMUKI Shoichi <tamuki@linet.gr.jp>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Russell King <linux@arm.linux.org.uk>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Cc: Anton Blanchard <anton@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Architectures implement dma_is_consistent() in different ways (some
misinterpret the definition of API in DMA-API.txt). So it hasn't been so
useful for drivers. We have only one user of the API in tree. Unlikely
out-of-tree drivers use the API.
Even if we fix dma_is_consistent() in some architectures, it doesn't look
useful at all. It was invented long ago for some old systems that can't
allocate coherent memory at all. It's better to export only APIs that are
definitely necessary for drivers.
Let's remove this API.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Architectures that handle DMA-non-coherent memory need to set
ARCH_DMA_MINALIGN to make sure that kmalloc'ed buffer is DMA-safe: the
buffer doesn't share a cache with the others.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Helge Deller <deller@gmx.de>
Cc: James E.J. Bottomley <jejb@parisc-linux.org>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
dma_get_cache_alignment returns the minimum DMA alignment. Architectures
defines it as ARCH_DMA_MINALIGN (formally ARCH_KMALLOC_MINALIGN). So we
can unify dma_get_cache_alignment implementations.
Note that some architectures implement dma_get_cache_alignment wrongly.
dma_get_cache_alignment() should return the minimum DMA alignment. So
fully-coherent architectures should return 1. This patch also fixes this
issue.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now each architecture has the own dma_get_cache_alignment implementation.
dma_get_cache_alignment returns the minimum DMA alignment. Architectures
define it as ARCH_KMALLOC_MINALIGN (it's used to make sure that malloc'ed
buffer is DMA-safe; the buffer doesn't share a cache with the others). So
we can unify dma_get_cache_alignment implementations.
This patch:
dma_get_cache_alignment() needs to know if an architecture defines
ARCH_KMALLOC_MINALIGN or not (needs to know if architecture has DMA
alignment restriction). However, slab.h define ARCH_KMALLOC_MINALIGN if
architectures doesn't define it.
Let's rename ARCH_KMALLOC_MINALIGN to ARCH_DMA_MINALIGN.
ARCH_KMALLOC_MINALIGN is used only in the internals of slab/slob/slub
(except for crypto).
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since "s3c-fb: Automatically calculate pixel clock when none is given",
there's no need for manually calculating the pixel clock anymore so remove
these lines and add the correct refresh rate where appropriately.
Signed-off-by: Maurus Cuelenaere <mcuelenaere@gmail.com>
Cc: Pawel Osciak <p.osciak@samsung.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: InKi Dae <inki.dae@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
S5PV210 SoCs allow enabling/disabling DMA channels per window. For a
window to display data from framebuffer memory, its channel has to be
enabled.
Signed-off-by: Pawel Osciak <p.osciak@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: InKi Dae <inki.dae@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add VSYNC interrupt support and an ioctl that allows waiting for it.
Interrupts are turned on only when needed.
Signed-off-by: Pawel Osciak <p.osciak@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: InKi Dae <inki.dae@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Supports all bpp modes.
The PRTCON register is used to disable in-hardware updates of registers
that store start and end addresses of framebuffer memory. This prevents
display corruption in case we do not make it before VSYNC with updating
them atomically. With this feature there is no need to wait for a VSYNC
interrupt before each such update.
Signed-off-by: Pawel Osciak <p.osciak@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: InKi Dae <inki.dae@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove the palette setup code from the header files and put it into the
main driver.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Pawel Osciak <p.osciak@samsung.com>
Cc: InKi Dae <inki.dae@samsung.com>
Cc: KyungMin Park <kyungmin.park.samsung.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Update the variant and window variant structures with the necessary
changes to support the older style of hardware where these are not in the
same place.
Add the support for the s3c2443/s3c2416 hardware by using the
platform-device s3c2443 to cover both, and add the initialisation data for
these.
Also change to including just the v4 header files for the moment until the
last of the merging of these is sorted out.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Pawel Osciak <p.osciak@samsung.com>
Cc: InKi Dae <inki.dae@samsung.com>
Cc: KyungMin Park <kyungmin.park.samsung.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove the various header files that configure this driver and use the
platform device name to select the correct configuration at probe time.
Currently this does not remove the header files, only updates the driver
and the relevant platform files.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Pawel Osciak <p.osciak@samsung.com>
Cc: InKi Dae <inki.dae@samsung.com>
Cc: KyungMin Park <kyungmin.park.samsung.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It has been working fine at 16bpp but in case of pixel format more then
24bpp it would occur distortedness situation on that mode. so this patch
set the word swap control bit of WINCONx to 1 as default value. but it
should be set to 0 in case that each ENLOCAL bit of WINCON0 ~ 2 registers
is enabled. this issue would be solved with local path feature soon.
Signed-off-by: InKi Dae <inki.dae@samsung.com>
Reviewed-by: KyungMin Park <kyungmin.park.samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Pawel Osciak <p.osciak@samsung.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
s5pv210 has five window layers (window0 ~ 4), among them, window0 ~ 2
could be used for local path with fimc(capture device) and fimd writeback
feature so this patch makes default window layer for UI to be set at
machine code.
Signed-off-by: InKi Dae <inki.dae@samsung.com>
Reviewed-by: KyungMin Park <kyungmin.park.samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Pawel Osciak <p.osciak@samsung.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
P4080 ESDHC controller does not support 1.8V and 3.0V voltage. but the
host controller capabilities register wrongly set the bits. This patch
adds the workaround to correct the weird voltage setting bits. Only 3.3V
voltage is supported for P4080 ESDHC controller.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Cc: Jerry Huang <Chang-Ming.Huang@freescale.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Cc: Jerry Huang <Chang-Ming.Huang@freescale.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pandora has TI WL1251 attached on MMC3, which is non-standard SDIO chip.
Make use MMC_QUIRK_NONSTD_SDIO to tell SDIO core about it.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Bob Copeland <me@bobcopeland.com>
Cc: Kalle Valo <kvalo@adurom.com>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Kishore Kadiyala <kishore.kadiyala@ti.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This will allow us to set up special cards in machine drivers just after
they are detected by MMC core.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Bob Copeland <me@bobcopeland.com>
Cc: Kalle Valo <kvalo@adurom.com>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Kishore Kadiyala <kishore.kadiyala@ti.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
No need to define ISA_DMA_THRESHOLD
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
[cmetcalf@tilera.com: converted to a single-line #include file]
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Since the writing to sysfs can free the old one, we need to block that
when we access the charp variables.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Phil Carmody <ext-phil.2.carmody@nokia.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Dan Williams <dcbw@redhat.com>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: Jing Huang <huangj@brocade.com>
Cc: James E.J. Bottomley <James.Bottomley@suse.de>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: David S. Miller <davem@davemloft.net>
Cc: user-mode-linux-devel@lists.sourceforge.net
Cc: libertas-dev@lists.infradead.org
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: linux-scsi@vger.kernel.org
Cc: linux-usb@vger.kernel.org
Until all supported versions of gcc recognize
-fno-strict-overflow, we should keep the RELOC_HIDE() magic in
__pa_symbol(). Comment it.
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
LKML-Reference: <1281508661-29507-1-git-send-email-namhyung@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Switch ia64/perfmon to using the d_dname() instead of relying on
__d_path() to prepend the name of the root dentry to the path.
CC: Tony Luck <tony.luck@intel.com>
CC: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
This patch is to add i2c driver support for nuc900.
Signed-off-by: Wan ZongShun <mcuos.com@gmail.org>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
As pointed out by Jiri Slaby: when I resolved the the 32-bit x85 system
call entry tables for prlimit (due to the conflict with fanotify), I
forgot to add the numbering in comments that we do for every fifth entry.
Reported-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-2.6.36' of git://git.kernel.dk/linux-2.6-block: (149 commits)
block: make sure that REQ_* types are seen even with CONFIG_BLOCK=n
xen-blkfront: fix missing out label
blkdev: fix blkdev_issue_zeroout return value
block: update request stacking methods to support discards
block: fix missing export of blk_types.h
writeback: fix bad _bh spinlock nesting
drbd: revert "delay probes", feature is being re-implemented differently
drbd: Initialize all members of sync_conf to their defaults [Bugz 315]
drbd: Disable delay probes for the upcomming release
writeback: cleanup bdi_register
writeback: add new tracepoints
writeback: remove unnecessary init_timer call
writeback: optimize periodic bdi thread wakeups
writeback: prevent unnecessary bdi threads wakeups
writeback: move bdi threads exiting logic to the forker thread
writeback: restructure bdi forker loop a little
writeback: move last_active to bdi
writeback: do not remove bdi from bdi_list
writeback: simplify bdi code a little
writeback: do not lose wake-ups in bdi threads
...
Fixed up pretty trivial conflicts in drivers/block/virtio_blk.c and
drivers/scsi/scsi_error.c as per Jens.
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6: (68 commits)
U6715 16550A serial driver support
Char: nozomi, set tty->driver_data appropriately
Char: nozomi, fix tty->count counting
serial: max3107: Fix gpiolib support
hsu: call PCI pm hooks in suspend/resume function
hsu: some code cleanup
hsu: add a periodic timer to check dma rx channel
hsu: driver for Medfield High Speed UART device
mxser: remove unnesesary NULL check
serial: add support for OX16PCI958 card
serial: 68328serial.c: remove dead (ALMA_ANS | DRAGONIXVZ | M68EZ328ADS)
timbuart: use __devinit and __devexit macros for probe and remove
serial: MMIO32 support for 8250_early.c
serial: mcf: don't take spinlocks in already protected functions
serial: general fixes in the serial_rs485 structure
serial: fix missing bit coverage of ASYNC_FLAGS
serial: "altera_uart: simplify altera_uart_console_putc()" checkpatch fixes
serial: crisv10: formatting of pointers in printk()
vt: Fix warning: statement with no effect due to vt_kern.h
tty_io: remove casts from void*
...
From: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH 12/19] ARM: cam60: don't use __init for cam60_spi_{flash_platform_data,partitions}
Date: Thu, 5 Aug 2010 16:08:46 +0200
Message-Id: <1281017333-5563-12-git-send-email-u.kleine-koenig@pengutronix.de>
These two structs are referenced by cam60_spi_devices. The latter is
copied at init time to kmalloced memory and so the copy isn't freed after
booting. So it must not contain references to .init memory.
This isn't noticed by modpost as cam60_spi_devices is in .init.data, too.
Noticed-and-Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
cam60_spi_devices is passed to at91_add_device_spi which calls
spi_register_board_info. The latter makes a copy of it, so living in
.init.data is OK.
This fixes the following warning in cam60_defconfig:
WARNING: vmlinux.o(.data+0x2a00): Section mismatch in reference from the variable cam60_spi_devices to the (unknown reference) .init.data:(unknown)
The variable cam60_spi_devices references
the (unknown reference) __initdata (unknown)
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for the dedicated FIFO mode on newer SoCs such as the S5PV210
partly to improve support and to fix the bug where any non-EP0 IN endpoint
requires its own FIFO allocation.
To fix this, we ensure that any non-zero IN endpoint is given a TXFIFO
using the same allocation method as the periodic case (all our current
hardware has enough FIFOs and FIFO memory for a 1:1 mapping) and ensure
that the necessary transmission done interrupt is enabled.
The default settings from reset for the core point all EPs at FIFO0,
used for the control endpoint. However, the controller documentation
states that all IN endpoints _must_ have a unique FIFO to avoid any
contention during transmission.
Note, this leaves us with a large IN FIFO for EP0 (which re-uses the
old NPTXFIFO) for an endpoint which cannot shift more than a pair of
packets at a time... this is a waste, but it looks like we cannot
re-allocate space to the individual IN FIFOs as they are already
maxed out (to be confirmed).
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
1) Introduce ulpi specific flags for control of the ulpi phy
2) Extend the generic ulpi driver with support for Function and
Interface control of upli phy
3) Update the platforms using the generic ulpi driver with new ulpi
flags
4) Remove the otg control flags not in use
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
zorro: Fix reading of proc/bus/zorro/* in small chunks
zorro: BKL removal
m68k/mac: Fix RTC on PMU machines
m68k/mac: Add color classic ii support
arch/m68k/sun3/leds.c: Checkpatch cleanup
Commit
7536cf9 (ARM: imx: dynamically register spi_imx devices (imx27))
introduced a variable named "pca100_spi0_data" but passed
"&pca100_spi_0_data" to imx27_add_spi_imx0. This wasn't noticed earlier
because both SPI_IMX and MACH_PCA100 are not enabled in mx27_defconfig.
This fixes a build failure:
arch/arm/mach-imx/mach-pca100.c: In function 'pca100_init':
arch/arm/mach-imx/mach-pca100.c:411: error: 'pca100_spi_0_data' undeclared (first use in this function)
arch/arm/mach-imx/mach-pca100.c:411: error: (Each undeclared identifier is reported only once
arch/arm/mach-imx/mach-pca100.c:411: error: for each function it appears in.)
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This moves the U300 timer code to look up its clock rate from the
clock framework as is apropriate and also switches it over to use
the generic code for *calc_mult_shift() on clock source and clock
event.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This removes the quirks to clock the U300 VIC and timer by custom
hooks and moves the control out to the clock framework where it
belongs. This is possible now that clocks are available early.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This fixes a regression due to the new apb_pclk stuff in the U300
platform, makes it run by splitting the apb clock off the single
UART clocks. For the MMCI and PL022 clocks we don't split them:
these are actually hardwired to the same clock terminal and will
thus simply have a double reference count and will be referenced
twice.
We also move clock registration to .init_irq() so they are
available early enough for probing to be successful and remove the
earlier quirk to clock primecells during PrimeCell registration.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This converts the U300 to uninverted logic for MMCI card detect,
fixing a regression in the current tree.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On versions of the Cortex-A9 prior to r2p0, performing TLB invalidations by
ASID match can result in the incorrect ASID being broadcast to other CPUs.
As a consequence of this, the targetted TLB entries are not invalidated
across the system.
This workaround changes the TLB flushing routines to invalidate entries
regardless of the ASID.
Cc: <stable@kernel.org>
Tested-by: Rob Clark <rob@ti.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The first read from ETM OS save and restore register after the power
down bit deassertion returns garbage.
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Alexander Shishkin <virtuoso@slind.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add a comment describing the mcount variants and how the callsites look
like.
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The mcount implementation currently uses a different indentation style
from the rest of the file (and the rest of the ARM assembly in the
kernel). Clean it up.
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
"ARM: Auto calculate ZRELADDR and provide option for exceptions" broke
the Thumb-2 decompressor because it removed an entry in the LC0 table
but didn't adjust the offset the Thumb-2 code uses to load the SP from
that table.
Fix it, and also change the ARM code to use the separate SP-load since
ARM instructions that include the SP in the LDM register list are
deprecated.
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This is a follow up to
14cb0de (arm/imx/gpio: add spinlock protection)
and fixes the following build failure:
CC arch/arm/mach-imx/pcm970-baseboard.o
In file included from arch/arm/include/asm/gpio.h:6,
from include/linux/gpio.h:8,
from arch/arm/mach-imx/pcm970-baseboard.c:20:
arch/arm/plat-mxc/include/mach/gpio.h:40: error: expected specifier-qualifier-list before 'spinlock_t'
Cc: stable@kernel.org
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6:
[S390] dasd: tunable missing interrupt handler
[S390] dasd: allocate fallback cqr for reserve/release
[S390] topology: use default MC domain initializer
[S390] initrd: change default load address
[S390] cmm, smsgiucv_app: convert sender to uppercase
[S390] cmm: add missing __init/__exit annotations
[S390] cio: use all available paths for some internal I/O
[S390] ccwreq: add ability to use all paths
[S390] cio: ccw_device_online_store return -EINVAL in case of missing driver
[S390] cio: Log the response from the unit check handler
[S390] cio: CHSC SIOSL Support
This patch is against the 2.6.34 source.
Paraphrased from the 1989 BSD patch by David Borman @ cray.com:
These are the changes needed for the kernel to support
LINEMODE in the server.
There is a new bit in the termios local flag word, EXTPROC.
When this bit is set, several aspects of the terminal driver
are disabled. Input line editing, character echo, and mapping
of signals are all disabled. This allows the telnetd to turn
off these functions when in linemode, but still keep track of
what state the user wants the terminal to be in.
New ioctl:
TIOCSIG Generate a signal to processes in the
current process group of the pty.
There is a new mode for packet driver, the TIOCPKT_IOCTL bit.
When packet mode is turned on in the pty, and the EXTPROC bit
is set, then whenever the state of the pty is changed, the
next read on the master side of the pty will have the TIOCPKT_IOCTL
bit set. This allows the process on the server side of the pty
to know when the state of the terminal has changed; it can then
issue the appropriate ioctl to retrieve the new state.
Since the original BSD patches accompanied the source code for telnet
I've left that reference here, but obviously the feature is useful for
any remote terminal protocol, including ssh.
The corresponding feature has existed in the BSD tty driver since 1989.
For historical reference, a good copy of the relevant files can be found
here:
http://anonsvn.mit.edu/viewvc/krb5/trunk/src/appl/telnet/?pathrev=17741
Signed-off-by: Howard Chu <hyc@symas.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As Jeff Dike pointed out, the Hayes ESP driver was removed in commit
f53a2ade0b, so these ioctl definitions
should also be removed. This cleans up the remaining arch-specific
locations of this ioctl value.
Thanks to Arnd for pointing these out.
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'writable_limits' of git://decibel.fi.muni.cz/~xslaby/linux:
unistd: add __NR_prlimit64 syscall numbers
rlimits: implement prlimit64 syscall
rlimits: switch more rlimit syscalls to do_prlimit
rlimits: redo do_setrlimit to more generic do_prlimit
rlimits: add rlimit64 structure
rlimits: do security check under task_lock
rlimits: allow setrlimit to non-current tasks
rlimits: split sys_setrlimit
rlimits: selinux, do rlimits changes under task_lock
rlimits: make sure ->rlim_max never grows in sys_setrlimit
rlimits: add task_struct to update_rlimit_cpu
rlimits: security, add task_struct to setrlimit
Fix up various system call number conflicts. We not only added fanotify
system calls in the meantime, but asm-generic/unistd.h added a wait4
along with a range of reserved per-architecture system calls.
