Prior to 2.6.18rc1 you could install with devices on a JMicron chipset
using the "all-generic-ide" option. As of this kernel the AHCI driver
grabs the controller and rams it into AHCI mode losing the PATA ports
and making CD drives and the like vanish. The all-generic-ide option
fails because the AHCI driver grabbed the PCI device and reconfigured
it.
To fix this three things are needed.
#1 We must put the chip into dual function mode
#2 The AHCI driver must grab only function 0 (already in your rc1 tree)
#3 Something must grab the PATA ports
The attached patch is the minimal risk edition of this. It puts the chip
into dual function mode so that AHCI will grab the SATA ports without
losing the PATA ports. To keep the risk as low as possible the third
patch adds the PCI identifiers for the PATA port and the FN check to the
ide-generic driver. There is a more featured jmicron driver on its way
but that adds risk and the ide-generic support is sufficient to install
and run a system.
The actual chip setup done by the quirk is the precise setup recommended
by the vendor.
(The JMB368 appears only in the ide-generic entry as it has no AHCI so
does not need the quirk)
Signed-off-by: Alan Cox <alan@redhat.com>
Acked-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It looks like someone confused kmem_cache_create with a different allocator
and was attempting to give it knowledge of how many cache entries there
were.
With the unfortunate result that each slab entry was big enough to hold
every irq.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is confirmed to fix a hang due to PCI resource conflicts with
setting up the Cardbus bridge on old laptops with the 440MX chipsets.
Original report by Alessio Sangalli, lspci debugging help by Pekka
Enberg, and trial patch suggested by Daniel Ritz:
"From the docs available i would _guess_ this thing is really similar
to the 82443BX/82371AB combination. at least the SMBus base address
register is hidden at the very same place (32bit at 0x90 in function
3 of the "south" brigde)"
The dang thing is largely undocumented, but the patch was corroborated
by Asit Mallick:
"I am trying to find the register information. 440MX is an integration of
440BX north-bridge without AGP and PIIX4E (82371EB). PIIX4 quirk
should cover the ACPI and SMBus related I/O registers."
and verified to fix the problem by Alessio.
Cc: Daniel Ritz <daniel.ritz-ml@swissonline.ch>
Cc: Asit Mallick <asit.k.mallick@intel.com>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Dmitry Torokhov <dtor_core@ameritech.net>
Tested-by: Alessio Sangalli <alesan@manoweb.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
ACPI: ACPI_DOCK: Initialize the atomic notifier list
ACPI: acpi_os_allocate() fixes
ACPI: SBS: fix initialization, sem2mutex
ACPI: add 'const' to several ACPI file_operations
ACPI: delete some defaults from ACPI Kconfig
ACPI: "Device `[%s]' is not power manageable" make message debug only
ACPI: ACPI_DOCK Kconfig
Revert "Revert "ACPI: dock driver""
ACPI: acpi_os_get_thread_id() returns current
ACPI: ACPICA 20060707
The pci channel state is currently uninitialized, thus there are two ways
of indicating that "everything's OK": 0 and 1. This is a bit of a burden.
If a devce driver wants to check if the pci channel is in a working or a
disconnected state, the driver writer must perform checks similar to
if((pdev->error_state != 0) &&
(pdev->error_state != pci_channel_io_normal)) {
whatever();
}
which is rather akward. The first check is needed because stuct pci_dev is
inited to all-zeros. The scond is needed because the error recovery will
set the state to pci_channel_io_normal (which is not zero).
This patch fixes this awkwardness.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It's useful to be able to turn off CONFIG_HOTPLUG for compile-coverage testing
and for section-checking coverage. But a few things go and select
CONFIG_HOTPLUG, making it a royal PITA to turn the thing off.
It's only turnable offable if CONFIG_EMBEDDED anyway. So let's make those
things depend on HOTPLUG, not select it.
Cc: Greg KH <greg@kroah.com>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
HOTPLUG_PCI_ACPI depends on ACPI_DOCK
ACPI_IBM_DOCK depends on ACPI_DOCK=n
ACPI_DOCK is EXPERIMENTAL, though that doesn't seem to mean much
Signed-off-by: Len Brown <len.brown@intel.com>
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/pci-2.6:
[PATCH] i386: export memory more than 4G through /proc/iomem
[PATCH] 64bit Resource: finally enable 64bit resource sizes
[PATCH] 64bit Resource: convert a few remaining drivers to use resource_size_t where needed
[PATCH] 64bit resource: change pnp core to use resource_size_t
[PATCH] 64bit resource: change pci core and arch code to use resource_size_t
[PATCH] 64bit resource: change resource core to use resource_size_t
[PATCH] 64bit resource: introduce resource_size_t for the start and end of struct resource
[PATCH] 64bit resource: fix up printks for resources in misc drivers
[PATCH] 64bit resource: fix up printks for resources in arch and core code
[PATCH] 64bit resource: fix up printks for resources in pcmcia drivers
[PATCH] 64bit resource: fix up printks for resources in video drivers
[PATCH] 64bit resource: fix up printks for resources in ide drivers
[PATCH] 64bit resource: fix up printks for resources in mtd drivers
[PATCH] 64bit resource: fix up printks for resources in pci core and hotplug drivers
[PATCH] 64bit resource: fix up printks for resources in networks drivers
[PATCH] 64bit resource: fix up printks for resources in sound drivers
[PATCH] 64bit resource: C99 changes for struct resource declarations
Fixed up trivial conflict in drivers/ide/pci/cmd64x.c (the printk that
was changed by the 64-bit resources had been deleted in the meantime ;)
This patch-queue improves the generic IRQ layer to be truly generic, by adding
various abstractions and features to it, without impacting existing
functionality.
While the queue can be best described as "fix and improve everything in the
generic IRQ layer that we could think of", and thus it consists of many
smaller features and lots of cleanups, the one feature that stands out most is
the new 'irq chip' abstraction.
The irq-chip abstraction is about describing and coding and IRQ controller
driver by mapping its raw hardware capabilities [and quirks, if needed] in a
straightforward way, without having to think about "IRQ flow"
(level/edge/etc.) type of details.
This stands in contrast with the current 'irq-type' model of genirq
architectures, which 'mixes' raw hardware capabilities with 'flow' details.
The patchset supports both types of irq controller designs at once, and
converts i386 and x86_64 to the new irq-chip design.
As a bonus side-effect of the irq-chip approach, chained interrupt controllers
(master/slave PIC constructs, etc.) are now supported by design as well.
The end result of this patchset intends to be simpler architecture-level code
and more consolidation between architectures.
We reused many bits of code and many concepts from Russell King's ARM IRQ
layer, the merging of which was one of the motivations for this patchset.
This patch:
rename desc->handler to desc->chip.
Originally i did not want to do this, because it's a big patch. But having
both "desc->handler", "desc->handle_irq" and "action->handler" caused a
large degree of confusion and made the code appear alot less clean than it
truly is.
I have also attempted a dual approach as well by introducing a
desc->chip alias - but that just wasnt robust enough and broke
frequently.
So lets get over with this quickly. The conversion was done automatically
via scripts and converts all the code in the kernel.
This renaming patch is the first one amongst the patches, so that the
remaining patches can stay flexible and can be merged and split up
without having some big monolithic patch act as a merge barrier.
[akpm@osdl.org: build fix]
[akpm@osdl.org: another build fix]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Dock bridges generally do not implement _SUN, yet show up as ejectable
slots. If you have more than one ejectable slot that does not implement
SUN, with the current code you will get duplicate slot numbers. So, if
there is no _SUN, use the current count of the number of slots found
instead.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Modify the acpiphp driver to use the ACPI dock driver for dock
notifications. Only load the acpiphp driver if we find we have pci dock
devices.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Based on a patch series originally from Vivek Goyal <vgoyal@in.ibm.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is needed if we wish to change the size of the resource structures.
Based on an original patch from Vivek Goyal <vgoyal@in.ibm.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivial:
typo fixes
Clean up 'inline is not at beginning' warnings for usb storage
Storage class should be first
i386: Trivial typo fixes
ixj: make ixj_set_tone_off() static
spelling fixes
fix paniced->panicked typos
Spelling fixes for Documentation/atomic_ops.txt
move acknowledgment for Mark Adler to CREDITS
remove the bouncing email address of David Campbell
CC drivers/pci/msi-apic.o
In file included from include/asm/msi.h:11,
from drivers/pci/msi.h:71,
from drivers/pci/msi-apic.c:8:
include/asm/smp.h:103: error: syntax error before '->' token
akpm: nasty. It appears to be
static inline unsigned int cpu_mask_to_apicid(cpumask_t cpumask)
conflicting with include/asm-x86_64/mach_apic.h's
#define cpu_mask_to_apicid (genapic->cpu_mask_to_apicid)
And I don't know which patch in rc4-mm1 triggered this.
Fixing this in the .c file seems wrong.
Including asm/smp.h instead of linux/smp.h seems wrong too. Need that
.config.
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The nVidia CK804 PCI-E chipset supports the AER extended capability
but sometimes fails to link it (with some BIOS or after a warm reboot).
It makes the AER cap invisible to pci_find_ext_capability().
The patch adds a quirk to set the missing bit that controls the
linking of the capability.
By the way, it removes the corresponding code in the myri10ge driver.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Loic Prylli <loic@myri.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
From: Doug Thompson <norsk5@yahoo.com>
This patch adds the 'broken_parity_status' sysfs attribute file to a PCI device.
Reading this attribute a userland program can determine if PCI device provides false
positives (value of 1) in its generation of PCI Parity status, or not (value of 0).
As PCI devices are found to be 'bad' in this regard, userland programs can also set
the appropriate value (root access only) of a faulty device. This per device
information will be used in the EDAC PCI Parity scanner code in a future patch once
this interface becomes available.
Signed-off-by: Doug Thompson <norsk5@yahoo.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Be more selective when running the MSI-K8T-Neo2Fir soundcard PCI quirk so
as not to run this on hardware where it's probably not needed.
Signed-off-by: Chris Wedgwood <cw@f00f.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
pci_walk_bus has a race with pci_destroy_dev. When cb is called
in pci_walk_bus, pci_destroy_dev might unlink the dev pointed by next.
Later on in the next loop, pointer next becomes NULL and cause
kernel panic.
Below patch against 2.6.17-rc4 fixes it by changing pci_bus_lock (spin_lock)
to pci_bus_sem (rw_semaphore).
Signed-off-by: Zhang Yanmin <yanmin.zhang@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The code is really not needed.
Roland Dreier/Greg KH removed the release_mem_region() calls that
were the only consumers of phys_addr:
http://www.ussg.iu.edu/hypermail/linux/kernel/0503.0/1540.html
patch below deletes the "dead" code.
Signed-off-by: Grant Grundler <iod00d@hp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A recent Stratus x86_64 platform uses a system ioapic that is a PCI device
located below a PCI bridge. Other platforms like this may exist.
This patch fixes a problem wherein the kernel's PCI setup code moves
the ioapic to an address other than that assigned by the BIOS. It simply
adds another exclusion (which already includes classless devices and host
bridges) to the function pbus_assign_resources_sorted so that it will not
move the ioapic.
If the ioapic is moved, the fixmap mapping to it is broken, so the OS should
leave it alone.
From: Kimball Murray <kimball.murray@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In IA64 platform, msi driver does not use irq_vector variable, and in
x86 platform LAST_DEVICE_VECTOR should one before FIRST_SYSTEM_VECTOR,
this patch modify this.
Signed-off-by: bibo, mao <bibo.mao@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Brice said the pci_save_msi_state breaks his driver in his special usage
(not in suspend/resume), as pci_save_msi_state will disable msi mode. In
his usage, pci_save_state will be called at runtime, and later (after
the device operates for some time and has an error) pci_restore_state
will be called.
In another hand, suspend/resume needs disable msi mode, as device should
stop working completely. This patch try to workaround this issue.
Drivers are expected call pci_disable_device in suspend time after
pci_save_state.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We recently ran into a problem where the e1000 device failed to
work properly on the kexec kernel. MSI was enabled for the
device in the main kernel when it crashed. The e1000 driver
tried to enable MSI on the kexec kernel, but the code bailed
early when it found that MSI was already enabled in the hardware,
even though the software state was not properly set up in the
kexec'd kernel. This patch fixes the problem by moving the
early return to after making sure that the software state
is properly initialized.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The PCI_BUS_FLAGS_NO_MSI bus flags does not appear do be inherited
correctly from the amd8131 MSI quirk to its parent busses. It makes
devices behind a bridge behind amd8131 try to enable MSI while the
amd8131 does not support it.
We fix this by looking at flags of all parent busses in
pci_enable_msi() and pci_enable_msix().
By the way, also add the missing dev->no_msi check in pci_enable_msix()
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently, the EDAC (error detection and correction) modules that are in
the kernel contain some features that need to be moved. After some good
feedback on the PCI Parity detection code and interface
(http://www.ussg.iu.edu/hypermail/linux/kernel/0603.1/0897.html) this
patch ADDs an new attribute to the pci_dev structure: Namely the
'broken_parity_status' bit.
When set this indicates that the respective hardware generates false
positives of Parity errors.
The EDAC "blacklist" solution was inferior and will be removed in a
future patch.
Also in this patch is a PCI quirk.c entry for an Infiniband PCI-X card
which generates false positive parity errors.
I am requesting comments on this AND on the possibility of a exposing
this 'broken_parity_status' bit to userland via the PCI device sysfs
directory for devices. This access would allow for enabling of this
feature on new devices and for old devices that have their drivers
updated. (SLES 9 SP3 did this on an ATI motherboard video device). There
is a need to update such a PCI attribute between kernel releases.
This patch just adds a storage place for the attribute and a quirk entry
for a known bad PCI device. PCI Parity reaper/harvestor operations are
in EDAC itself and will be refactored to use this PCI attribute instead
of its own mechanisms (which are currently disabled) in the future.
Signed-off-by: Doug Thompson <norsk5@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There were two instances of pci_acpi_init(), one in
drivers/pci/pci-acpi.c and another in arch/i386/pci/acpi.c.
Rename the one in pci-acpi.c and make it consistent with
other names in the same file.
Signed-off-by: Muthukumar R <muthur@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If a device is already enabled, don't bother reenabling it.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Acked-By: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds an "enable" sysfs attribute to each PCI device. When read it
shows the "enabled-ness" of the device, but you can write a "0" into it to
disable a device, and a "1" to enable it.
This later is needed for X and other cases where userspace wants to enable
the BARs on a device (typical example: to run the video bios on a secundary
head). Right now X does all this "by hand" via bitbanging, that's just evil.
This allows X to no longer do that but to just let the kernel do this.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
CC: Peter Jones <pjones@redhat.com>
Acked-by: Dave Airlie <airlied@linux.ie>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
PCI: Add pci_assign_resource_fixed -- allow fixed address assignments
On some embedded systems the PCI address for hotplug devices are not only
known a priori but are required to be at a given PCI address for other
master in the system to be able to access.
An example of such a system would be an FPGA which is setup from user space
after the system has booted. The FPGA may be access by DSPs in the system
and those DSPs expect the FPGA at a fixed PCI address.
Added pci_assign_resource_fixed() as a way to allow assignment of the PCI
devices's BARs at fixed PCI addresses.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When we detect a 64-bit pre-set address in a BAR on a 32-bit platform,
we disable it and treat it as if it had been unset, thus allowing the
general address assignment code to assign a new address to it when the
device is enabled. This can happen either if the firmware assigns
64-bit addresses; additionally, some cards have been found "in the
wild" which do not come out of reset with all the BAR registers set to
zero.
Unfortunately, the patch that implemented this tested the low part of
the address instead of the high part of the address. This patch fixes
that.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
[pci] Ignore pre-set 64-bit BARs on 32-bit platforms
Currently, Linux always rejects a device which has a pre-set 64-bit
address on a 32-bit platform. On systems which do not do PCI
initialization in firmware, this causes some devices which don't
correctly power up with all BARs zero to fail.
This patch makes the kernel automatically zero out such an address
(thus treating it as if it had not been set at all, meaning it will
assign an address if necessary).
I have done this only for devices, not bridges. It seems potentially
hazardous to do for bridges.
Signed-off-by: H. Peter Anvin <hpa@c2micro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
MSI callouts for altix. Involves a fair amount of code reorg in sn irq.c
code as well as adding some extensions to the altix PCI provider abstaction.
Signed-off-by: Mark Maule <maule@sgi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Abstract IA64_FIRST_DEVICE_VECTOR/IA64_LAST_DEVICE_VECTOR since SN platforms
use a subset of the IA64 range. Implement this by making the above macros
global variables which the platform can override in it setup code.
Also add a reserve_irq_vector() routine used by SN to mark a vector's as
in-use when that weren't allocated through assign_irq_vector().
Signed-off-by: Mark Maule <maule@sgi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Abstract portions of the MSI core for platforms that do not use standard
APIC interrupt controllers. This is implemented through a new arch-specific
msi setup routine, and a set of msi ops which can be set on a per platform
basis.
Signed-off-by: Mark Maule <maule@sgi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove checks for value, since the hotplug core always provides
a valid value.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Current SHPCHP driver shows device number of slots in info messages,
but it is useless and should be replaced with slot name.
This patch replaces the device number shown in the info messages with
the slot name.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Cc: Kristen Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes unused hpc_event_lock. This patch has no functional
change.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Cc: Kristen Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch cleans up the interrupt polling timer code in
shpchp_hpc.c. This has no functional changes.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Cc: Kristen Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch cleans up the code related to issuing SHPC commands. This
patch has no functional changes.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Cc: Kristen Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch cleans up the interrupt handler of shpchp driver. This
patch has no functional changes.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Cc: Kristen Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch implements .get_address callback of hotplug_slot_ops for
PCIEHP driver. With this patch, we can see bus address of hotplug
slots as follows:
# cat /sys/bus/pci/slots/0010_0000/address
0000:0a:00
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Cc: Kristen Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch replaces pci_find_slot() with pci_get_slot() in PCIEHP
driver. This patch enables PCI Express Hotplug on the system which has
multiple PCI domains.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Cc: Kristen Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a repost of a patch submitted by Prarit Bhargava on 01-19-06 that
never got integrated.
The get_power_status function is currently reporting a bitwise mapping of
the slot if the slot is powered on. It should return 1 if powered on and
0 if powered off.
Signed-off-by: Mike Habeck <habeck@sgi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The workqueue thread of shpchp driver should be created only when SHPC
based hotplug slots are detected on the system.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Cc: Kristen Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Global SERR and Interrupt should be masked at shpchp driver unload time.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Cc: Kristen Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Current SHPCHP driver doesn't take care of RsvdP/RsvdZ[*] bits in
controller SERR-INT register. This might cause unpredicable
results. This patch fixes this bug.
[*] RsvdP and RsvdZ are defined in SHPC spec as follows:
RsvdP - Reserved and Preserved. Register bits of this type are
reserved for future use as R/W bits. The value read is
undefined. Writes are ignored. Software must follow These rules
when accessing RsvdP bits:
- Software must ignore RsvdP bits when testing values read
from these registers.
- Software must not depend on RsvdP bit's ability to retain
information when written
- Software must always write back the value read in the RsvdP
bits when writing one of these registers.
RsvdZ - Reserved and Zero. Register bits of this type are reserved
for future use as R/WC bits. The value read is undefined. Writes
are ignored. Software must follow these rules when accessing RsvdZ
bits:
- Software must ignore RsvdZ bits when testing values read
from these registers.
- Software must not depends on a RsvdZ bit's ability to retain
information when written.
- Software must always write 0 to RsvdZ bits when writing one
of these register.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Cc: Kristen Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Current SHPCHP driver doesn't take care of RsvdP/RsvdZ[*] bits
in logical slot registers. This might cause unpredicable results. This
patch fixes this bug.
[*] RsvdP and RsvdZ are defined in SHPC spec as follows:
RsvdP - Reserved and Preserved. Register bits of this type are
reserved for future use as R/W bits. The value read is
undefined. Writes are ignored. Software must follow These rules
when accessing RsvdP bits:
- Software must ignore RsvdP bits when testing values read
from these registers.
- Software must not depend on RsvdP bit's ability to retain
information when written
- Software must always write back the value read in the RsvdP
bits when writing one of these registers.
RsvdZ - Reserved and Zero. Register bits of this type are reserved
for future use as R/WC bits. The value read is undefined. Writes
are ignored. Software must follow these rules when accessing RsvdZ
bits:
- Software must ignore RsvdZ bits when testing values read
from these registers.
- Software must not depends on a RsvdZ bit's ability to retain
information when written.
- Software must always write 0 to RsvdZ bits when writing one
of these register.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Cc: Kristen Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch cleans up the code to access bits in slot logical
registers. This patch has no functional change.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Cc: Kristen Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch cleans up the code to access slot logical registers. This
patch has no functional changes.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Cc: Kristen Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch cleans up the code to access SHPC working register
sets. This patch has no functional changes.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Cc: Kristen Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Current PCHEHP driver doesn't have any code to program hotplug
parameters from firmware. So hotplug parameters are never programed at
hot-add time. This patch add support for programming hotplug
parameters to PCIEHP driver.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Cc: Kristen Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support for _HPX (Hot Plug Parameter Extensions)
defined in ACPI3.0a spec.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Cc: Kristen Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch converts the improper error message about OSHP evaluation
to debug message which is displayed only when pci_hotplug.ko is loaded
with debugging mode enabled. To do this, this patch adds a new module
parameter "debug_acpi" to pci_hotplug.ko for enabling/disabling debug
messages in acpi_pcihp.c.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Cc: Kristen Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes the problem that hotplug parameters are not programed
when PCI cards are hot-added by ACPIPHP, SHPCHP and PCIEHP driver. The
pci_dev structure being hot-added is not bound to ACPI handle, so we
need to trace PCI bus tree to find ACPI handle.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Cc: Kristen Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Don't call pci_enable_device from pciehp because the pcie port service driver
already does this.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
acpi_os_free should not be used by drivers outside
of acpi/*/*.c. Replace with kfree().
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When acpiphp_enable_slot() is failed, acpiphp does not change
the slot->flags. Therefore, when user tries to read power
status, acpiphp_get_power_status() returns the enable status
whether the slot is not really enabled.
This patch fixes this BUG.
Signed-off-by: MUNEDA Takahiro <muneda.takahiro@jp.fujitsu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I encountered the problem that when there are some hotplug
slots are under the host bridge, the hotplug slots under the
p2p bridge are not treated as hotpluggable.
This patch fixes this BUG.
Signed-off-by: MUNEDA Takahiro <muneda.takahiro@jp.fujitsu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
o hotplug slots add
When the hot-added PCI device is p2p bridge, acpiphp calls
find_p2p_bridge() to add hotplug slots.
o hotplug slots remove
When the hot-removing PCI device is p2p bridge, acpiphp
calls cleanup_p2p_bridge() to remove hotplug slots.
o notify handler exchange
When the p2p bridge is added, acpiphp changes the notify
hanlder.
If no bridge device is inserted into the hotpluggable PCI
slot, acpiphp installs the notify handler for function.
After the p2p bridge hot-add, acpiphp has to install the
notify handler for bridge. Because, the role of the
handlers are not same. The hot-remove case is ditto.
Signed-off-by: MUNEDA Takahiro <muneda.takahiro@jp.fujitsu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Current acpiphp does not free acpi_device structs when the
PCI devices are removed. When the PCI device is added,
acpi_bus_add() fails because acpi_device struct has already
exists. So, _PRT method does not evaluate.
This patch fixes this issue.
Signed-off-by: MUNEDA Takahiro <muneda.takahiro@jp.fujitsu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
SGI hotplug driver changes required to support Tollhouse system PCI
hotplug, and implements the PRF_HOTPLUG_SUPPORT feature bit.
Signed-off-by: Prarit Bhargava <prarit@sgi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
According to Intel ICH spec, there are several rules that Base Address
should be programmed before IOSE (PCICMD register ) enabled.
For example ICH7:
12.1.3 SATA : the base address register for the bus master register
should be programmed before this bit is set.
11.1.3: PCICMD (USB): The base address register for USB should be
programmed before this bit is set.
....
To make sure kernel code follow this rule , and prevent unnecessary
confusion. I proposal this patch.
Signed-off-by: Luming Yu <luming.yu@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
At least one laptop blew up on resume from suspend with a black screen due
to a lack of this patch. By only writing back config space that is
different, we minimise the possibility of accidents like this.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We currently don't handle errors properly when resuming a PCI device:
* In pci_default_resume() we capture the error code returned by
pci_enable_device() but don't pass it up to the caller.
Introduced by commit 95a629657d
* In pci_resume_device(), the errors possibly returned by the driver's
.resume method or by the generic pci_default_resume() function are
ignored.
This patch fixes both issues.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch revives pci_find_ext_capability (has been disabled a couple month
ago since it was not used anywhere. See http://lkml.org/lkml/2006/1/20/247).
It will now be used by the myri10ge driver.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Andrew J. Gallatin <gallatin@myri.com>
drivers/pci/pci.c | 3 +--
include/linux/pci.h | 2 ++
2 files changed, 3 insertions(+), 2 deletions(-)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The OSC set and query functions do not allocate enough space for return
values, and set the output buffer length to a false, too large value. This
causes the acpi-ca code to assume that the output buffer is larger than it
actually is, and overwrite memory when copying acpi return buffers into
this caller provided buffer. In some cases this can cause kernel oops if
the memory that is overwritten is a pointer. This patch will change these
calls to use a dynamically allocated output buffer, thus allowing the
acpi-ca code to decide how much space is needed.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Cc: "Brown, Len" <len.brown@intel.com>
Cc: "Yu, Luming" <luming.yu@intel.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Do not enable the SMBus device on Asus boards if suspend is used. We do
not reenable the device on resume, leading to all sorts of undesirable
effects, the worst being a total fan failure after resume on Samsung P35
laptop.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Signed-off-by: Pavel Machek <pavel@suse.cz>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
An earlier commit (75cf7456dd) changed an
overly-zealous PCI quirk to only poke those VIA devices that need it.
However, some PCI devices were not included in what I hope is now the full
list. Consequently we're failing to run the quirk on all machines which need
it, causing IRQ routing failures.
This should I hope correct this.
Thanks to Masoud Sharbiani <masouds@masoud.ir> for pointing this out
and testing the fix.
Signed-off-by: Chris Wedgwood <cw@f00f.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Alan Cox pointed out that the VIA 'IRQ fixup' was erroneously running
on my system which has no VIA southbridge (but I do have a VIA IEEE
1394 device).
This should address that. I also changed "Via IRQ" to "VIA IRQ"
(initially I read Via as a capitalized via (by way/means of).
Signed-off-by: Chris Wedgwood <cw@f00f.org>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The coverity checker spotted (as entry #599) that we might leak `entry' in
drivers/pci/msi.c::msix_capability_init()
This patch should take care of that.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On the MSI-K8T-NEO2 FIR ( Athlon-64, Socket 939 with VIA-K8T800- Chipset
and onboard Sound,... ) the BIOS lets you choose "DISABLED" or "AUTO" for
the On-Board Sound Device.
If you add another PCI-Sound-Card the BIOS disables the on-board device.
So far I have a Quirk, that does set the correspondent BIT in the
PCI-registers to enable the soundcard.
But how to ensure that the code is executed ONLY on excactly this kind of
boards (not any other with similar Chipset)?
Cc: Jaroslav Kysela <perex@suse.cz>
Acked-by: Takashi Iwai <tiwai@suse.de>
Cc: Lee Revell <rlrevell@joe-job.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/pci-2.6: (169 commits)
commit 78a596b449
Author: Adrian Bunk <bunk@stusta.de>
Date: Fri Mar 31 01:38:12 2006 -0800
[PATCH] remove kernel/power/pm.c:pm_unregister()
Since the last user is removed in -mm, we can now remove this long deprecated
function.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 21440d3133
Author: David Brownell <david-b@pacbell.net>
Date: Sat Apr 1 10:21:52 2006 -0800
[PATCH] dma doc updates
...
The Asus A6VA notebook was reported to need a PCI quirk to unhide
the SMBus.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The init function for the RPA PCI Hotplug driver returns -ENODEV in the
case that no hotplug-capable slots are detected in the system. This is
bad, since hot-capable slots can be added after boot to a purely virtual
POWER partition. This is also bad because DLPAR I/O operations depend
on the rpaphp module.
Change the rpaphp init module to return success for the case of
partitions that own no hotplug-capable slots at boot. Such slots can be
dynamically added after boot.
Signed-off-by: John Rose <johnrose@austin.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The naming of the constant defined for PCI ID 1022:7450 does not seem
to match the information at http://pciids.sourceforge.net/:
http://pci-ids.ucw.cz/iii/?i=1022
There 1022:7450 is listed as "AMD-8131 PCI-X Bridge" while 1022:7451
is listed as "AMD-8131 PCI-X IOAPIC". Yet, the current definition for
0x7450 is PCI_DEVICE_ID_AMD_8131_APIC. It seems to me like that name
should map to 0x7451, while a name like PCI_DEVICE_ID_AMD_8131_BRIDGE
should map to 0x7450.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Print more diagnostic info to help identify the source of power management
suspend failures.
Example:
usb_hcd_pci_suspend(): pci_set_power_state+0x0/0x1af() returns -22
pci_device_suspend(): usb_hcd_pci_suspend+0x0/0x11b() returns -22
suspend_device(): pci_device_suspend+0x0/0x34() returns -22
Work-in-progress. It needs lots more suspend_report_result() calls sprinkled
everywhere.
Cc: Patrick Mochel <mochel@digitalimplant.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Nigel Cunningham <nigel@suspend2.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Semaphore to mutex conversion.
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Dave Jones <davej@codemonkey.org.uk>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Jens Axboe <axboe@suse.de>
Cc: Neil Brown <neilb@cse.unsw.edu.au>
Acked-by: Alasdair G Kergon <agk@redhat.com>
Cc: Greg KH <greg@kroah.com>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Adam Belay <ambx1@neo.rr.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I encountered the problem that the insmod of the acpiphp
fails because of the mis-freeing of the memory.
I tested this patch on my tiger4 box.
Signed-off-by: MUNEDA Takahiro <muneda.takahiro@jp.fujitsu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes the defines TRUE and FALSE and just uses 0 or 1.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
shpchprm_acpi.c and pciehprm_acpi.c are nearly identical. In addition,
there are functions in both these files that are also in acpiphp_glue.c.
This patch will remove duplicate functions from shpchp, pciehp, and
acpiphp and move this functionality to pci_hotplug, as it is not
hardware specific. Get rid of shpchprm* and pciehprm* files since they
are no longer needed. shpchprm_nonacpi.c and pciehprm_nonacpi.c are
identical, as well as shpchprm_legacy.c and can be replaced with a
macro.
This patch also changes acpiphp to use the common hpp code.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this patch converts drivers/pci to kzalloc usage.
Compile tested with allyes config.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Current ACPIPHP driver scans only slots under the top level PCI-to-PCI
bridge. So hotplug PCI slots under the nested PCI-to-PCI bridge would
not be detected. For example, if the system has the ACPI namespace
like below, hotplug slots woule not be detected.
Device (PCI0) { /* Root bridge */
Name (_HID, "PNP0A03")
Device (P2PA) { /* PCI-to-PCI bridge */
Name (_ADR, ...)
Device (P2PB) { /* PCI-to-PCI bridge */
Name (_ADR, ...)
Device (S0F0) { /* hotplug slot */
Name (_ADR, ...)
Name (_SUN, ...)
Method (_EJ0, ...) { ... }
}
...
Device (S0F7) { /* hotplug slot */
Name (_ADR, ...)
Name (_SUN, ...)
Method (_EJ0, ...) { ... }
}
Device (S1F0) { /* hotplug slot */
Name (_ADR, ...)
Name (_SUN, ...)
Method (_EJ0, ...) { ... }
}
...
}
}
}
This patch fixes this issue.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When doing a hotplug removal of a PPB, sn_bus_store_sysdata()
needs to be called for the PPB and all of its children.
Acked-by: Prarit Bhargava <prarit@sgi.com>
Signed-off-by: John Keller <jpk@sgi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The code related to handling bus speed in SHPCHP driver is
unnecessarily complex. This patch cleans up and simplify that.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add missing 'const' to pci_request_region[s] 'res_name' arg,
since we pass it directly to __request_region(), whose 'name' arg
is also const.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Several drivers are starting to grow options to disable MSI. However,
it's often a host chipset issue, not something which individual drivers
should handle. So we add the pci=nomsi kernel parameter to allow the user
to disable MSI modes for systems we haven't added to the quirk list yet.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch contains the scheduled removal of PCI_LEGACY_PROC.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Coverity checker correctly noted, that in function board_replaced in
drivers/pci/hotplug/cpqphp_ctrl.c, the variable src always has the
value 8, and therefore much code after the
...
if (rc || src) {
...
if (rc)
return rc;
else
return 1;
}
...
can never be called.
This patch removes the unreachable code in this function fixing kernel
Bugzilla #6073.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When hotplug slot is under the host bridge,
DEVICE_ACPI_HANDLE(&bus->self->dev) fails since '&bus->self' was not set.
This patch fixes it.
This patch is based on kristen's latest patches.
I tested this patch on my Tiger4.
Signed-off-by: MUNEDA Takahiro <muneda.takahiro@jp.fujitsu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
o This patch removes IDs (for slots management).
o This patch removes the slot register/unregister processes
from the init/exit phases. Instead, adds these processes
in the bridge add/cleanup phases.
o Currently, this change doesn't have any meanings. But
these changes are needed to support p2p bridge(with
hotplug slot)
Signed-off-by: MUNEDA Takahiro <muneda.takahiro@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
These patches add generic dock event handling to acpiphp. If there are
pci devices that need to be inserted/removed after the dock event, the
event notification will be handed down to the normal pci hotplug event
handler in acpiphp so that new bridges/devices can be enumerated.
Because some dock stations do not have pci bridges or pci devices that
need to be inserted after a dock, acpiphp will remain loaded to handle
dock events even if no hotpluggable pci slots are discovered.
You probably need to have the pci=assign-busses kernel parameter enabled
to use these patches, and you may not allow ibm_acpi to handle docking
notifications and use this patch.
This patch incorporates feedback provided by many.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If we add a new bridge with subordinate busses, we should call make sure
that acpi is notified so that the PRT (if present) can be read and drivers
who have registered on this bus will be notified when it is started.
Also make sure to use the max reserved bus number for the starting the bus
scan.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as659) fixes a might_sleep problem in the PCI core, by moving
a call to pci_dev_put() outside the scope of a spinlock.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
"In some cases, especially on modern laptops with a lot of PCI and cardbus
bridges, we're unable to assign correct secondary/subordinate bus numbers
to all cardbus bridges due to BIOS limitations unless we are using
"pci=assign-busses" boot option." -- Ivan Kokshaysky (from a patch comment)
Without it, Cardbus cards inserted are never seen by PCI because the parent
PCI-PCI Bridge of the Cardbus bridge will not pass and translate Type 1 PCI
configuration cycles correctly and the system will fail to find and
initialise the PCI devices in the system.
Reference: PCI-PCI Bridges: PCI Configuration Cycles and PCI Bus Numbering:
http://www.science.unitn.it/~fiorella/guidelinux/tlk/node72.html
The reason for this is that:
``All PCI busses located behind a PCI-PCI bridge must reside between the
secondary bus number and the subordinate bus number (inclusive).''
"pci=assign-busses" makes pcibios_assign_all_busses return 1 and this
turns on PCI renumbering during PCI probing.
Alan suggested to use DMI automatically set assign-busses on problem systems.
The only question for me was where to put it. I put it directly before
scanning PCI bus into pcibios_scan_root() because it's called from legacy,
acpi and numa and so it can be one place for all systems and configurations
which may need it.
AMD64 Laptops are also affected and fixed by assign-busses, and the code is
also incuded from arch/x86_64/pci/ that place will also work for x86_64
kernels, I only ifdef'-ed the x86-only Laptop in this example.
Affected and known or assumed to be fixed with it are (found by googling):
* ASUS Z71V and L3s
* Samsung X20
* Compaq R3140us and all Compaq R3000 series laptops with TI1620 Controller,
also Compaq R4000 series (from a kernel.org bugreport)
* HP zv5000z (AMD64 3700+, known that fixup_parent_subordinate_busnr fixes it)
* HP zv5200z
* IBM ThinkPad 240
* An IBM ThinkPad (1.8 GHz Pentium M) debugged by Pavel Machek
gives the correspondig message which detects the possible problem.
* MSI S260 / Medion SIM 2100 MD 95600
The patch also expands the "try pci=assign-busses" warning so testers will
help us to update the DMI table.
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use "unsigned long" when dealing with PCI resources.
The BAR Indicator Register (BIR) can be a 64-bit value
or the resource could be a 64-bit host physical address.
Enables ib_mthca and cciss drivers to use MSI-X on ia64 HW.
Problem showed up now because of new system firmware on one platform.
Symptom will either be memory corruption or MCA.
Second part of this patch deals with "useless" code.
We walk through the steps to find the phys_addr and then
don't use the result. I suspect the intent was to zero
out the respective MSI-X entry but I'm not sure at the moment.
Delete the code inside the #if 0/#endif if it's really
not needed.
Signed-off-by: Grant Grundler <iod00d@hp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It turns out AMD 8131 quirk only affects MSI for devices behind the 8131 bridge.
Handle this by adding a flags field in pci_bus, inherited from parent to child.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On ASUS A8V and A8V Deluxe boards, the onboard AC97 audio controller
and MC97 modem controller are deactivated when a second PCI soundcard
is present. This patch enables them.
Signed-off-by: Bauke Jan Douma <bjdouma@xs4all.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I attach a trivial patch for 2.6.15.4 that unhides SMBus controller
on an HP Compaq nx6110 notebook.
Signed-off-by: Tomasz Koprowski <tomek@koprowski.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The extra compatability code is not necessary. Any code still using
the old shutdown method will trigger the warning in driver_register()
instead.
Signed-off-by: Brian Gerst <bgerst@didntduck.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Current SHPCHP driver doesn't care about the confliction between
hotplug operation via sysfs and hotplug operation via attention
button. So if those ware conflicted, slot could be an unexpected
state.
This patch changes SHPCHP driver to handle slot state properly. With
this patch, slot events are handled according to the current slot
state as shown at the Table below.
Table. Slot States and Event Handling
=========================================================================
Slot State Event and Action
=========================================================================
STATIC - Go to POWERON state if user initiates
(Slot enabled, insertion request via sysfs
Slot disabled) - Go to POWEROFF state if user initiates removal
request via sysfs
- Go to BLINKINGON state if user presses
attention button when the slot is disabled
- Go to BLINKINGOFF state if user presses
attention button when the slot is enabled
The event handler of SHPCHP driver is unnecessarily very complex. In
addition, current event handler can only a fixed number of events at
the same time, and some of events would be lost if several number of
events happened at the same time.
This patch simplify the event handler by using 'work queue', and it
also fix the above-mentioned issue.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The wait_for_ctrl_irq() function in SHPCHP driver is no longer needed.
This patch removes that. This patch has no functional change.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes unused 'pci_bus' member from controller structure.
This patch have no functional change.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
> On Mon, Feb 13, 2006 at 05:13:21PM -0800, David S. Miller wrote:
> >
> > In drivers/pci/probe.c:pci_scan_bridge(), if this is not the first
> > pass (pass != 0) we don't restore the PCI_BRIDGE_CONTROL_REGISTER and
> > thus leave PCI_BRIDGE_CTL_MASTER_ABORT off:
> >
> > int __devinit pci_scan_bridge(struct pci_bus *bus, struct pci_dev * dev, int max, int pass)
> > {
> > ...
> > /* Disable MasterAbortMode during probing to avoid reporting
> > of bus errors (in some architectures) */
> > pci_read_config_word(dev, PCI_BRIDGE_CONTROL, &bctl);
> > pci_write_config_word(dev, PCI_BRIDGE_CONTROL,
> > bctl & ~PCI_BRIDGE_CTL_MASTER_ABORT);
> > ...
> > if ((buses & 0xffff00) && !pcibios_assign_all_busses() && !is_cardbus) {
> > unsigned int cmax, busnr;
> > /*
> > * Bus already configured by firmware, process it in the first
> > * pass and just note the configuration.
> > */
> > if (pass)
> > return max;
> > ...
> > }
> >
> > pci_write_config_word(dev, PCI_BRIDGE_CONTROL, bctl);
> > ...
> >
> > This doesn't seem intentional.
Agreed, looks like an accident. The patch [1] originally came from Kip
Walker (Broadcom back then) between 2.6.0-test3 and 2.6.0-test4. As I
recall it was supposed to fix an issue with with PCI aborts being
signalled by the PCI bridge of the Broadcom BCM1250 family of SOCs when
probing behind pci_scan_bridge. It is undeseriable to disable
PCI_BRIDGE_CTL_MASTER_ABORT in pci_{read,write)_config_* and the
behaviour wasn't considered a bug in need of a workaround, so this was
put in probe.c.
I don't have an affected system at hand, so can't really test but I
propose something like the below patch.
[1] http://www.linux-mips.org/git?p=linux.git;a=commit;h=599457e0cb702a31a3247ea6a5d9c6c99c4cf195
[PCI] Avoid leaving MASTER_ABORT disabled permanently when returning from pci_scan_bridge.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Current SHPCHP driver has a bug in its interrupt handler which cause
"IRQ #: nobody cared" oops. This problem can be reproduced easily by
the following operation.
# cd /sys/bus/pci/slots/<slot#>
# while true; do echo 1 > attention ; done &
The reason is that when command complete interrupt is raised, current
SHPCHP driver's interrupt handler returns IRQ_NONE regardless of if
the interrupt is handled or not.
This patch fixes this issue.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch moves slot name area into struct slot.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes unnecessary 'magic' member from struct slot of
SHPCHP driver.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch replaces kmalloc() and memset() pair with kzalloc() and
cleans up the arg of sizeof() in SHPCHP driver.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch cleans up pcihp_skelton.c as follows.
o Move slot name area into struct slot.
o Replace kmalloc with kzalloc and clean up the arg of sizeof()
o Fix the wrong use of get_*_status() functions.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Current shpchp driver might cause system panic because of lack of
serialization. It can be reproduced very easily by the following
operation.
# cd /sys/bus/pci/slots/<slot#>
# while true; do echo 0 > power ; echo 1 > power ; done &
# while true; do echo 0 > power ; echo 1 > power ; done &
This patch fixes this issue by changing shpchp to get appropreate
semaphore for hot-plug operation.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch cleanups codes that check the command status. For this, it
introduces a new semaphore "cmd_sem" for each controller.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch cleanups some codes in shpchp_core.c. This patch has no
functional changes.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch cleanups init_slots() function of SHPCHP driver based on
pcihp_skelton.c. This patch has no functional change.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
semaphore to mutex conversion.
the conversion was generated via scripts, and the result was validated
automatically via a script as well.
build tested with allyesconfig.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The IBM Dock II cardbus bridges require some extra configuration
before Yenta is loaded in order to setup the Interrupts to be
routed properly.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
After you find the maximum value of the subordinate buses below the child
bus, you must fix the parent's subordinate bus number again, otherwise
it may be too small.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Change the semantics of this call to return the max reserved
bus number instead of just the max assigned bus number.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Clean up: move assignments outside of if() statements.
AFAICT, no functional change. Easier to read/understand.
Depends on "[PATCH 1/3] msi vector targeting abstractions"
by Mark Maule <maule@sgi.com>.
I expect one hunk to fail if applied against 2.6.15.
This is essentially Joe Perches' patch.
I've cleaned up the one instance added by Mark's patch.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Build break: Building PCI hotplug on PowerPC results in
a build break, due to failure to export symbols.
Reported today by Dave Jones <davej@redhat.com>:
drivers/pci/hotplug/rpaphp.ko needs unknown symbol pcibios_add_pci_devices
This patch fixes same problem in drivers/pci tree
Previous patch fixes the break in the arch/powerpc tree.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Error checking is scattered through various layers of the dlpar code,
leading to a somewhat opaque code structure. This patch consolidates
error checking in one routine, simplifying the code a tad. There's
also some whitespace cleanup here too.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Acked-by: John Rose <johnrose@austin.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Minor cleanup. Move structure initializer to bottom of file,
this allows elimination of eyeball-strain-inducing forward
declarations.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Acked-by: John Rose <johnrose@austin.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Minor cleanup. Add the prefix rpaphp_* to several generic-sounding routines.
Remove rpaphp_remove_slot(), which is a one-liner.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Acked-by: John Rose <johnrose@austin.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove general baroqueness. The function rpaphp_enable_pci_slot()
has a fairly simple logic structure, once all of the debug printk's
are removed. Its called from only one place, and that place also
has a very simple structure once he printk's are removed. Merge
the two together.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Acked-by: John Rose <johnrose@austin.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove general baroqueness. The function rpaphp_unconfig_pci_adapter()
is really just three lines of code, once all the dbg printks are removed.
And its called in only one place. So replace the call by the thre lines.
Also, provide proper semaphore locking in the affected function
disable_slot()
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Acked-by: John Rose <johnrose@austin.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The function rpaphp_eeh_remove_bus_device() is a dupe of
eeh_remove_bus_device(). Remove it.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Acked-by: John Rose <johnrose@austin.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove general baroqueness. The function rpaphp_config_pci_adapter()
is really just one line of code, once all the dbg printks are removed.
And its called in only one place. So replace the call by the one line.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Acked-by: John Rose <johnrose@austin.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The function rpaphp_fixup_new_pci_devices() has been migrated to
pcibios_fixup_new_pci_devices() in
arch/powerpc/platforms/pseries/pci_dlpar.c
This patch removes the old version.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Acked-by: John Rose <johnrose@austin.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The function rpaphp_find_pci_bus() has been migrated to
pcibios_find_pci_bus() in arch/powerpc/platforms/pseries/pci_dlpar.c
This patch removes the old version.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Acked-by: John Rose <johnrose@austin.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes the AMD POGO errata on the hotplug controller where the
platform will lock up or reboot if PERR/SERR generation is enabled and a
slot is sent an enable command. This fix disables PERR/SERR generation
before a slot is sent the enable command by first saving related
registers, turning off SERR/PERR generation, enabling the slot, then
restoring the registers.
Signed-off-by: David Keck <david.keck@amd.com>
Cc: Kristen Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Removing and then adding a PCI slot to a running partition results in
a kernel panic. The current code attempts to add iospace for an entire
root bus, which is inappropriate, and silently fails. When a pci device
tries to use the iospace, a page fault is taken, as the iospace had not
been mapped, and of course the page fault cannot be resolved.
This only occurs for PCI adapters using pio, which may be why it hadn't
been seen earlier (this seems to have been broken for a while).
This patch has survived testing of dozens of slot add and removes.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Acked-by: John Rose <johnrose@austin.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The RPAPHP hoplug driver will not build as a module, because it calls
on pci_claim_resource(), which is not exported. This exports the symbol.
Problem reported by Olaf Hering <olh@suse.de>
A grep indicates that building drivers/parisc/lba_pci.c
would have trouble building as a module for the same reason.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I missed this usage in drivers/pci/msi.h:
#ifdef CONFIG_SMP
#define set_msi_irq_affinity set_msi_affinity
#else
#define set_msi_irq_affinity NULL
#endif
set_msi_affinity() is declared and exclusively used in msi.c.
Here's a better way so (hopefully) history doesn't repeat itself.
Signed-off-by: Grant Grundler <iod00d@hp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch #if 0's the unused global function pci_find_ext_capability().
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The lock validator caught another one: drivers/pci/msi.c is accessing
&irq_desc[i].lock with interrupts enabled (!).
The fix is to disable interrupts properly.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Move the PCI bus device probe/remove methods to the bus_type
structure. We leave the shutdown method alone since there
are compatibility issues with that.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch converts the inode semaphore to a mutex. I have tested it on
XFS and compiled as much as one can consider on an ia64. Anyway your
luck with it might be different.
Modified-by: Ingo Molnar <mingo@elte.hu>
(finished the conversion)
Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch contains the following cleanups:
- hotplug/pciehp_core.c: make the needlessly global hpdriver_context
static
- #if 0 the following unused functions:
- pci.c: pci_bus_max_busnr()
- pci.c: pci_max_busnr()
- proc.c: pci_proc_attach_bus()
- remove.c: pci_remove_device_safe
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Only size the bus that has been added.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Compaq PCI Hotplug driver was creating 2 sysfs files that contained
nothing but debug information, and had way more than "one value" in
them. This patch converts the code to use debugfs for these files
instead.
Compile tested only.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Here's a small patch to reduce the nr. of pointer dereferences in
drivers/pci/hotplug/pciehp_core.c
Benefits:
- micro speed optimization due to fewer pointer derefs
- generated code is slightly smaller
- small line length cleanup
- better readability
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Here's a small patch to reduce the nr. of pointer dereferences in
drivers/pci/hotplug/pciehprm_acpi.c
Benefits:
- micro speed optimization due to fewer pointer derefs
- generated code is slightly smaller
- better readability
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Here's a small patch to reduce the nr. of pointer dereferences in
drivers/pci/hotplug/rpaphp_pci.c
Benefits:
- micro speed optimization due to fewer pointer derefs
- generated code should be slightly smaller
- better readability
note: due to lack of both hardware and cross-compile tools this patch is,
unfortunately, completely untested.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Here's a small patch to reduce the nr of pointer dereferences in
drivers/pci/hotplug/cpqphp_core.c
Benefits of this patch:
- micro speed optimization due to fewer pointer derefs
- generated code is slightly smaller
- tiny line length and whitespace cleanup
- better readability
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The powerpc PCI code sets up the PCI tree without doing config space
accesses in most cases, from the firmware tree. However, it still wants
to call pci_cfg_space_size() under some conditions, thus it needs to
be made non-static (though I don't see a point to export it to modules).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add a warning if a child bus may be inaccessible because the
parent bridge has wrong secondary or subordinate bus numbers.
Note that this may or may not happen on "transparent" bridges,
as can be seen in bug #5557.
Also, if we do not fix up the assignment of bus numbers, try to
make use of the bus number space available.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes bugs in the pciehp driver that prevent hot-add
of a card with PCI bridges on it.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch disables power fault, MRL sensor and presence detection
interrupts when a PCIe slot is powered-off and enables those
interrupts when it is powered-on again. This is necessary to prevent
the associated events from causing an endless cycle of interrupts
due to the power-fault bit, which stays set till power is restored
to the slot.
Signed-off-by: Thomas Schaefer <thomas.schaefer@kontron.com>
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I've implemented a quirk to take advantage of the 1KB I/O space
granularity option on the Intel P64H2 PCI Bridge. I had to change
probe.c because it sets the resource start and end to be aligned on 4k
boundaries (after the quirk sets them to 1k boundaries). I've tested
this patch on a Unisys ES7000-600 both with and without the 1KB option
enabled. I also tested this on a 2 processor Dell box that doesn't have
a P64H2 to make sure there were no negative affects there.
Signed-off-by: Dan Yeisley <dan.yeisley@unisys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The following patch implements .get_address callback of
hotplug_slot_ops for SHPCHP driver. With this patch, we
can see bus address of hotplug slots as follows:
$ cat address
0000:0b:01
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The RPAPHP code contains two routines that appear to be gratuitous copies
of very similar pci code. In particular,
rpaphp_claim_resource ~~ pci_claim_resource
(there is a minor, non-functional difference)
rpadlpar_claim_one_bus == pcibios_claim_one_bus
(the code is identical)
This patch removes the rpaphp versions of the code.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Acked-by: John Rose <johnrose@austin.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The RPAPHP code contains a routine that duplicates some existing code.
This patch removes the rpaphp version of the code.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Acked-by: John Rose <johnrose@austin.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Current SHPCHP driver uses msleep_interruptible() function to wait for
a command completion event. But I think this would cause an unnecessary
long wait until timeout, if command completion interrupt came before
task state was changed to TASK_INTERRUPTIBLE. This patch fixes this
issue. With this patch, command completion becomes faster as follows:
o Without this patch
# time echo 1 > power
real 0m4.708s
user 0m0.000s
sys 0m0.524s
o With this patch
# time echo 1 > power
real 0m2.221s
user 0m0.000s
sys 0m0.532s
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Current SHPCHP driver writes a '0' to the Command Completion Detect
bit to clear the Command Complete Interrupt Pending. But according to
the SHPC spec (See 4.7.3.1 System Interrupts), SHPCHP driver must
write '1'. This patch fixes this bug.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Current SHPCHP driver seems not to map MMIO region properly. This
patch fixes this bug. This patch also cleanup the code.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The hpc_get_mode1_ECC_cap() function of SHPCHP driver seems to refer
the wrong bit for refering the "Mode 1 ECC Capability" bit. This bug
seems not to cause any problem so far. But I think this should be
fixed. This patch fixes this bug.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The hpc_get_max_bus_speed() function of the SHPCHP driver seems to
refer wrong bits in the "Slot Avail Register I" and "Slot Avail
Register II". This patch fixes this bug. And this also cleanup the
code.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch replaces pci_find_slot() with pci_get_slot() in the SHPCHP
driver. This enables SHPCHP driver to work on multiple PCI segment
systems.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Coverity checker spotted that we already did return -ENOMEM
if (!p_mem_node).
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I noticed what appears to be a cut/paste error in
drivers/pci/hotplug/ibmphp_pci.c:
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The bus_id string must be unique for all devices of that bus in the
system, not just for devices with the same parent - otherwise multiple
symlinks with identical names appear in /sys/bus/pci_express/devices.
Signed-off-by: Sergey Vlasov <vsu@altlinux.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Call pci_read_irq() for bridges too, so that the pin value
is stored for bridges that require interrupts.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use the stored value of the interrupt pin rather than try to read
the config again.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Store the value of the INTERRUPT_PIN in the pci_dev structure
so that it can be retrieved later.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Include fixes for 2.6.14-git11. Should allow to remove sched.h from
module.h on i386, x86_64, arm, ia64, ppc, ppc64, and s390. Probably more
to come since I haven't yet checked the other archs.
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Leave the overloaded "hotplug" word to susbsystems which are handling
real devices. The driver core does not "plug" anything, it just exports
the state to userspace and generates events.
Signed-off-by: Kay Sievers <kay.sievers@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
PCI express hotplug uses the pcieportbus driver so pcie must be
initialized before hotplug/. This patch changes the link order.
Signed-Off-By: Milton Miller <miltonm@bga.com>
Acked-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Combined mode sucks. Especially when both libata and the legacy IDE
drivers try to drive ports on the same device, since that makes DMA
rather difficult.
This patch addresses the problem by allowing the user to control which
driver binds to the ports in a combined mode configuration. In many
cases, they'll probably want the libata driver to control both ports
since it can use DMA for talking with ATAPI devices (when
libata.atapi_enabled=1 of course). It also allows the user to get old
school behavior by letting the legacy IDE driver bind to both ports.
But neither is forced, the patch doesn't change current behavior unless
one of combined_mode=ide or combined_mode=libata is passed
on the boot line. Either of those options may require you to access
your devices via different device nodes (/dev/hd* in the ide case
and /dev/sd* in the libata case), though of course if you have udev
installed nicely you may not notice anything. :)
Let me know if the documentation is too cryptic, I'd be happy to expand
on it if necessary. I think most users will want to boot with
'combined_mode=libata' and add 'options libata atapi_enabled=1'
to their modules.conf to get good DVD playing and disk behavior
(haven't tested CD or DVD writing though).
I'd much rather things behave sanely by default (i.e. DMA for devices on
both ports), but apparently that's difficult given the various chip
bugs and hardware configs out there (not to mention that people's
drives may suddenly change from /dev/hdc to /dev/sdb), so this boot
option may be the correct long term fix.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Per the PCI Express spec, the power-fault-detected bit in the
slot status register can be set anytime hardware detects a power
fault, regardless of whether the slot has a device populated in
it or not. This bit is sticky and must be explicitly cleared.
This patch is needed to allow hot-add after such a power fault
has been detected.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
drivers/pci/hotplug/pciehp_hpc.c:221: parse error before "pcie_isr"
drivers/pci/hotplug/pciehp_hpc.c:221: warning: type defaults to `int' in declaration of `pcie_isr'
drivers/pci/hotplug/pciehp_hpc.c:221: warning: data definition has no type or storage class
drivers/pci/hotplug/pciehp_hpc.c: In function `hpc_release_ctlr':
drivers/pci/hotplug/pciehp_hpc.c:715: implicit declaration of function `free_irq'
drivers/pci/hotplug/pciehp_hpc.c: At top level:
drivers/pci/hotplug/pciehp_hpc.c:839: parse error before "pcie_isr"
drivers/pci/hotplug/pciehp_hpc.c:840: warning: return type defaults to `int'
drivers/pci/hotplug/pciehp_hpc.c: In function `pcie_isr':
drivers/pci/hotplug/pciehp_hpc.c:850: `IRQ_NONE' undeclared (first use in this function)
drivers/pci/hotplug/pciehp_hpc.c:850: (Each undeclared identifier is reported only once
drivers/pci/hotplug/pciehp_hpc.c:850: for each function it appears in.)
drivers/pci/hotplug/pciehp_hpc.c:979: `IRQ_HANDLED' undeclared (first use in this function)
drivers/pci/hotplug/pciehp_hpc.c: In function `pcie_init':
drivers/pci/hotplug/pciehp_hpc.c:1362: implicit declaration of function `request_irq'
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
(akpm: _machine is some ppc64 thing - this is a powerpc-only driver)
Signed-off-by: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
MSI hardcoded delivery mode to use logical delivery mode. Recently
x86_64 moved to use physical mode addressing to support physflat mode.
With this mode enabled noticed that my eth with MSI werent working.
msi_address_init() was hardcoded to use logical mode for i386 and x86_64.
So when we switch to use physical mode, things stopped working.
Since anyway we dont use lowest priority delivery with MSI, its always
directed to just a single CPU. Its safe and simpler to use
physical mode always, even when we use logical delivery mode for IPI's
or other ioapic RTE's.
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch contains the following cleanups:
- access.c should #include "pci.h" for getting the prototypes of it's
global functions
- hotplug/shpchp_pci.c: make the needlessly global function
program_fw_provided_values() static
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch contains the driver bits for enabling DLPAR and PCI Hotplug
for the new OF-based PCI probe. This functionality was regressed when
the new PCI approach was introduced. Please apply if appropriate.
Signed-off-by: John Rose <johnrose@austin.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A nice feature of sysfs is that it can create the symlink from the
driver to the module that is contained in it.
It requires that the device_driver.owner is set, what is not the
case for many PCI drivers.
This patch allows pci_register_driver to set automatically the
device_driver.owner for any PCI driver.
Credits to Al Viro who suggested the method.
Signed-off-by: Laurent Riffard <laurent.riffard@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
--
drivers/ide/setup-pci.c | 12 +++++++-----
drivers/pci/pci-driver.c | 9 +++++----
include/linux/ide.h | 3 ++-
include/linux/pci.h | 10 ++++++++--
4 files changed, 22 insertions(+), 12 deletions(-)
store_new_id() should not be (and cannot be) inline;
the function pointer is stored in a device_attribute table.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Move the PPC fixup for old NCR 810 controllers to generic quirks -
it's needed for Alpha, x86 and other architectures that use
setup-bus.c.
Thanks to Jay Estabrook for pointing out the issue.
Signed-off-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The quirk names for VIA 686 are mistyped in 2.6.14 (686 vs 868). S3 868
influence? :) Here is a patch to correct them.
Signed-off-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The current pciehp implementation reports a power-fail error
even if the condition has cleared by the time the corresponding
interrupt handling code gets a chance to run. This patch
fixes this problem.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch further tweaks how we request control of hotplug
controller hardware from BIOS. We first search the ACPI namespace
corresponding to a specific hotplug controller looking for an
_OSC or OSHP method. On failure, we successively move to the
ACPI parent object, till we hit the highest level host bridge
in the hierarchy. This allows for different types of BIOS's
which place the _OSC/OSHP methods at various places in the acpi
namespace, while still not encroaching on the namespace of
some other root level host bridge.
This patch also introduces a new load time option (pciehp_force)
that allows us to bypass all _OSC/OSHP checking. Not supporting
these methods seems to be be the most common ACPI firmware problem
we've run into. This will still _not_ allow the pciehp driver to
work correctly if the BIOS really doesn't support pciehp (i.e. if
it doesn't generate a hotplug interrupt). Use this option with
caution. Some BIOS's may deliberately not build any _OSC/OSHP
methods to make sure it retains control the hotplug hardware.
Using the pciehp_force parameter for such systems can lead to
two separate entities trying to control the same hardware.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch tweaks the way pciehp requests control of the hotplug
hardware from BIOS. It now tries to invoke the ACPI _OSC method
for a specific hotplug controller only, rather than walking the
entire acpi namespace invoking all possible _OSC methods under
all host bridges. This allows us to gain control of each hotplug
controller individually, even if BIOS fails to give us control of
some other hotplug controller in the system.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Reduce the number of debug messages generated if pciehp debug is
enabled. I tried to restrict this to removing debug messages that
are either early-driver-debug type messages, or print information
that can be inferred through other debug prints.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
State information is currently stored in per-slot as well as
per-pci-function data structures in pciehp. There's a lot of
overlap in the information kept, and some of it is never used.
This patch consolidates the state information to per-slot and
eliminates unused data structures. The biggest change is to
eliminate the pci_func structure and the code around managing
its lists.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Reduce the PCI Express hotplug driver's dependence on ACPI.
We don't walk the acpi namespace anymore to build a list of
bridges and devices. We go to ACPI only to run the _OSC or
_OSHP methods to transition control of hotplug hardware from
system BIOS to the hotplug driver, and to run the _HPP
method to get hotplug device parameters like cache line size,
latency timer and SERR/PERR enable from BIOS.
Note that one of the side effects of this patch is that pciehp
does not automatically enable the hot-added device or its DMA
bus mastering capability now. It expects the device driver to
do that. This may break some drivers and we will have to fix
them as they are reported.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch converts the pci express hotplug controller driver
to use the PCI core for resource management. This eliminates a
lot of duplicated code and integrates pciehp with the system's
normal PCI handling code.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some devices have more than one capability of the same type. For
example, the PCI header for the PathScale InfiniPath looks like:
04:01.0 InfiniBand: Unknown device 1fc1:000d (rev 02)
Subsystem: Unknown device 1fc1:000d
Flags: bus master, fast devsel, latency 0, IRQ 193
Memory at fea00000 (64-bit, non-prefetchable) [size=2M]
Capabilities: [c0] HyperTransport: Slave or Primary Interface
Capabilities: [f8] HyperTransport: Interrupt Discovery and Configuration
There are _two_ HyperTransport capabilities, and the PathScale driver
wants to look at both of them.
The current pci_find_capability() API doesn't work for this, since it
only allows us to get to the first capability of a given type. The
patch below introduces a new pci_find_next_capability(), which can be
used in a loop like
for (pos = pci_find_capability(pdev, <ID>);
pos;
pos = pci_find_next_capability(pdev, pos, <ID>)) {
/* ... */
}
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
19-rpaphp-crashing.patch
This patch fixes a bug related to dlpar PHB add, after a PHB removal.
-- The crash was due to the PHB not having a pci_dn structure yet,
when the phb is being added.
This code survived testing, of adding and removeig the PHB and all slots
underneath it, 17 times so far, as of this writing.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This is the remaining misc drivers/ part of the big kfree cleanup patch.
Remove pointless checks for NULL prior to calling kfree() in misc files in
drivers/.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Acked-by: Aristeu Sergio Rozanski Filho <aris@cathedrallabs.org>
Acked-by: Roland Dreier <rolandd@cisco.com>
Acked-by: Pierre Ossman <drzeus@drzeus.cx>
Acked-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Len Brown <len.brown@intel.com>
Acked-by: "Antonino A. Daplas" <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix more include file problems that surfaced since I submitted the previous
fix-missing-includes.patch. This should now allow not to include sched.h
from module.h, which is done by a followup patch.
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I recently picked up my older work to remove unnecessary #includes of
sched.h, starting from a patch by Dave Jones to not include sched.h
from module.h. This reduces the number of indirect includes of sched.h
by ~300. Another ~400 pointless direct includes can be removed after
this disentangling (patch to follow later).
However, quite a few indirect includes need to be fixed up for this.
In order to feed the patches through -mm with as little disturbance as
possible, I've split out the fixes I accumulated up to now (complete for
i386 and x86_64, more archs to follow later) and post them before the real
patch. This way this large part of the patch is kept simple with only
adding #includes, and all hunks are independent of each other. So if any
hunk rejects or gets in the way of other patches, just drop it. My scripts
will pick it up again in the next round.
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Typo fix: dots appearing after a newline in printk strings.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add CONFIG_X86_32 for i386. This allows selecting options that only apply
to 32-bit systems.
(X86 && !X86_64) becomes X86_32
(X86 || X86_64) becomes X86
Signed-off-by: Brian Gerst <bgerst@didntduck.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This moves the PCI quirk handling for USB host controllers from the
PCI directory to the USB directory. Follow-on patches will need to:
(a) merge these copies with the originals in the HCD reset methods.
they don't wholly agree, despite doing the very same thing; and
(b) eventually change it so "usb-handoff" is the default, to help
get more robust USB/BIOS/input/... interactions.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/Makefile | 2
drivers/pci/quirks.c | 253 ---------------------------------------
drivers/usb/Makefile | 1
drivers/usb/host/Makefile | 5
drivers/usb/host/pci-quirks.c | 272 ++++++++++++++++++++++++++++++++++++++++++
5 files changed, 280 insertions(+), 253 deletions(-)
PCI: add descriptions for missing function parameters.
Eliminate all kernel-doc warnings here.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Allocate resources for adapters with bridges on them.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add a warning to pci driver registration code so that we know
whether we have drivers using the obsolete driver shutdown
method.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
At unload time, the shpchp driver does not remove sysfs files
it had created in the driver's probe entry point. This patch
fixes this problem.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Reduce the number of debug messages generated if shpchp debug is
enabled. I tried to restrict this to removing debug messages that
are either early-driver-debug type messages, or print information
that can be inferred through other debug prints.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove un-necessary header includes, remove dead code, remove
some type casts, receive function return in the correct data
type...
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
State information is currently stored in per-slot as well as
per-pci-function data structures in shpchp. There's a lot of
overlap in the information kept, and some of it is never used.
This patch consolidates the state information to per-slot and
eliminates unused data structures. The biggest change is to
eliminate the pci_func structure and the code around managing
its lists.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch eliminates saving the PCI config header for devices
in hotplug capable slots. We now use the PCI core to get the
specific parts of the config header as required.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The shpc driver registers its probe function for all pci-pci
bridges in the system. Not all of them will be shpc capable, so
look for this capability early in the probe function and return
if there's no work to do on this bridge. The old shpc driver
did some initialization work on all bridges before detecting
that shpc is not supported and unwinds the work it's already done
in that case.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Reduce the SHPC hotplug driver's dependence on ACPI. We don't
walk the acpi namespace anymore to build a list of bridges and
devices. The remaining interaction with ACPI is to run the
_OSHP method to transition control of hotplug hardware from
system BIOS to the shpc hotplug driver, and to run the _HPP
method to get hotplug device parameters like cache line size,
latency timer and SERR/PERR enable from BIOS.
Note that one of the side effects of this patch is that shpchp
does not enable the hot-added device or its DMA bus mastering
automatically now. It expects the device driver to do that.
This may break some drivers and we will have to fix them as
they are reported.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Info about resources assigned to PCI devices is already available
through sysfs and pci utilities. There's no need for shpchp to
create another sysfs file to display the same information.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch converts the standard hotplug controller driver to use
the PCI core for resource management. This eliminates a whole lot
of duplicated code, and integrates shpchp in the system's normal
PCI handling code.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
One more SMBus unhiding quirk, this time for the HP D530. Requested and
successfully tested by Ben Cranston.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a minor patch to the ppc64 PCI hotplug code; it makes the call to
rpaphp_unconfig_pci_adapter() symmetric with respect to the call to
rpaphp_config_pci_adapter(). I discussed this with John Rose, who
had provided the last round of changes for these functions; he
appearently had this patch but somehow failed to mail it out.
Tested. (added/removed device).
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
drivers/pci/hotplug/rpaphp.h | 3 ++-
drivers/pci/hotplug/rpaphp_core.c | 5 ++++-
drivers/pci/hotplug/rpaphp_pci.c | 11 +++--------
3 files changed, 9 insertions(+), 10 deletions(-)
This patch unhides hidden SMBus on ICH6 chipset installed in
Asus M6V notebook. I would like to thank Michal Mleczko for
testing and help.
Signed-Off-By: Rudolf Marek <r.marek@sh.cvut.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/pci/quirks.c | 24 ++++++++++++++++++++++++
1 file changed, 24 insertions(+)
Add pci_{enable,disable}_device() calls. Without pci_enable_device(),
dev->irq is garbage, and cpqphp relies on it.
This fixes a problem reported by Bruno Redondi. He reported a flood
of ACPI interrupts, that caused kacpid to run 100% of the time:
http://bugzilla.kernel.org/show_bug.cgi?id=5312
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/pci/hotplug/cpqphp_core.c | 24 +++++++++++++++++++-----
1 file changed, 19 insertions(+), 5 deletions(-)
Add pci_{enable,disable}_device() calls. Without pci_enable_device(),
dev->irq is garbage, and cpcihp_zt5550 relies on it.
Compiled but untested, since I don't have the hardware.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Scott Murray <scottm@somanetworks.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/pci/hotplug/cpcihp_zt5550.c | 25 +++++++++++++++++++++----
1 file changed, 21 insertions(+), 4 deletions(-)
Cleanup the need_restore switch statement in
pci_set_power_state(). This makes it more safe by explicitly handling
all the PCI power states instead of handling them as the default
case. It also reads a little better IMHO.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some PCI adapters (eg. ipr scsi adapters) have an exposure today in that they
issue BIST to the adapter to reset the card. If, during the time it takes to
complete BIST, userspace attempts to access PCI config space, the host bus
bridge will master abort the access since the ipr adapter does not respond on
the PCI bus for a brief period of time when running BIST. On PPC64 hardware,
this master abort results in the host PCI bridge isolating that PCI device
from the rest of the system, making the device unusable until Linux is
rebooted. This patch is an attempt to close that exposure by introducing some
blocking code in the PCI code. When blocked, writes will be humored and reads
will return the cached value. Ben Herrenschmidt has also mentioned that he
plans to use this in PPC power management.
Signed-off-by: Brian King <brking@us.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/pci/access.c | 89 ++++++++++++++++++++++++++++++++++++++++++++++++
drivers/pci/pci-sysfs.c | 20 +++++-----
drivers/pci/pci.h | 7 +++
drivers/pci/proc.c | 28 +++++++--------
drivers/pci/syscall.c | 14 +++----
include/linux/pci.h | 7 +++
6 files changed, 134 insertions(+), 31 deletions(-)
This patch just adds ACPI and GPIO regions to its LPC bridge, similar
way as ICH4 did. I would like to thank Michal Mleczko for testing.
Signed-off-by: Rudolf Marek <r.marek@sh.cvut.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/pci/quirks.c | 12 ++++++++++++
1 file changed, 12 insertions(+)
In PM v1, all devices were called at SUSPEND_DISABLE level. Then
all devices were called at SUSPEND_SAVE_STATE level, and finally
SUSPEND_POWER_DOWN level. However, with PM v2, to maintain
compatibility for platform devices, I arranged for the PM v2
suspend/resume callbacks to call the old PM v1 suspend/resume
callbacks three times with each level in order so that existing
drivers continued to work.
Since this is obsolete infrastructure which is no longer necessary,
we can remove it. Here's an (untested) patch to do exactly that.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When reserving an PCI quirk, note that in the kernel bootup messages.
Also, parse the strange PIIX4 device resources - they should get their
own PCI resource quirks, but for now just print out what it finds to
verify that the code does the right thing.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
That's what we've always historically done, and bigger windows seem to
confuse some cardbus bridges. Or something.
Alan reports that this makes the ThinkPad 600x series work properly
again: the 4kB IO window for some reason made IDE DMA not work, which
makes IDE painfully slow even if it works after DMA timeouts.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This still leaves driver and architecture-specific subdirectories alone,
but gets rid of the bulk of the "generic" generated files that we should
ignore.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This change makes quirk_intel_ide_combined() dependent on the precise
conditions under which it is needed:
* IDE is built in
* IDE SATA option is not set
* ata_piix or ahci drivers are enabled
This fixes an issue where some modular configurations would not cause
the quirk to be enabled.
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Linus torvalds <torvalds@osdl.org>
I believe the change that broke things is introduction of
pci_fixup_parent_subordinate_busnr().
The patch here does two things:
- hunk #1 should fix the problems you've seen when you boot without
additional "pci" kernel options;
- hunk #2 supposedly fixes boot with "pci=assign-busses" option which
otherwise hangs Acer TM81xx machines as reported.
Please try this with and without "pci=assign-busses". If it boots,
I'd like to see 'lspci -vvx' for both cases.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This function expects an unsigned 32-bit type as its third argument:
static u32 pci_size(u32 base, u32 maxbase, u32 mask)
However, given these definitions:
#define PCI_BASE_ADDRESS_MEM_MASK (~0x0fUL)
#define PCI_ROM_ADDRESS_MASK (~0x7ffUL)
these two calls in drivers/pci/probe.c are problematic for architectures
for which a UL is not equivalent to a u32:
sz = pci_size(l, sz, PCI_BASE_ADDRESS_MEM_MASK);
sz = pci_size(l, sz, PCI_ROM_ADDRESS_MASK);
Hence the below compile warning when building for ARCH=ppc64:
drivers/pci/probe.c: In function `pci_read_bases':
/.../probe.c:168: warning: large integer implicitly truncated to unsigned type
/.../probe.c:218: warning: large integer implicitly truncated to unsigned type
Here is a simple fix.
Signed-off-by: Amos Waterland <apw@us.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch converts kcalloc(1, ...) calls to use the new kzalloc() function.
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
PCI_ROM_ADDRESS is a 32 bit register and as such should be accessed using
pci_bus_{read,write}_config_dword(). A recent audit of drivers/ turned up
several cases of byte- and word-sized accesses. The harmful ones were fixed
by Linus directly. This patches up one of the remaining
harmless-but-still-wrong cases caught in the dragnet.
Signed-off-by: Adam Kropelin <akropel1@rochester.rr.com>
Cc: <kristen.c.accardi@intel.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
PCI_ROM_ADDRESS is a 32 bit register and as such should be accessed
using pci_bus_{read,write}_config_dword(). A recent audit of drivers/
turned up several cases of byte- and word-sized accesses. The harmful
ones were fixed by Linus directly. This patches up one of the remaining
harmless-but-still-wrong cases caught in the dragnet.
Signed-off-by: Adam Kropelin <akropel1@rochester.rr.com>
Cc: <kristen.c.accardi@intel.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
PCI_ROM_ADDRESS is a 32 bit register and as such should be accessed using
pci_bus_{read,write}_config_dword(). A recent audit of drivers/ turned up
several cases of byte- and word-sized accesses. The harmful ones were fixed
by Linus directly. This patches up one of the remaining
harmless-but-still-wrong cases caught in the dragnet.
Signed-off-by: Adam Kropelin <akropel1@rochester.rr.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Certain (SGI?) ia64 boxes object to having their PCI BARs
restored unless absolutely necessary. This patch restricts calling
pci_restore_bars from pci_set_power_state unless the current state
is PCI_UNKNOWN, the actual (i.e. physical) state of the device is
PCI_D3hot, and the device indicates that it will lose its configuration
when transitioning to PCI_D0.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
pcibus_to_cpumask expands into more than just an initialiser so gcc
moans about code before variable declarations.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch makes some small rearrangements of the PCI probing code in
order to make it possible for arch code to set up the PCI tree
without needing to duplicate code from the PCI layer unnecessarily.
PPC64 will use this to set up the PCI tree from the Open Firmware
device tree, which we need to do on logically-partitioned pSeries
systems.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Trivial patch against 2.6.13 to unhide SMBus on Compaq Evo N620c laptop using
Intel 82855PM chipset.
Signed-off-by: Rumen Zarev <rzarev@caltech.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Martin Franc reported that the pciehp driver was not enabling bus
master capability on his hot-plugged card. pciehprm_enable_card()
was updating the PCI command register only if _HPP indicated a
value for SERR or PERR that was different from the current setting.
I don't have hardware that reproduces this problem, but Martin
reports that this patch fixes the problem for him.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
From rzarev@its.caltech.edu Tue Sep 6 18:29:50 2005
Date: Tue, 6 Sep 2005 13:39:32 -0700 (PDT)
From: Rumen Ivanov Zarev <rzarev@its.caltech.edu>
Message-Id: <200509062039.j86KdWMr014934@inky.its.caltech.edu>
To: gregkh@suse.de
Subject: PCI: Unhide SMBus on Compaq Evo N620c
Cc: linux-kernel@vger.kernel.org
Trivial patch against 2.6.13 to unhide SMBus on Compaq Evo N620c laptop using
Intel 82855PM chipset.
Signed-off-by: Rumen Zarev <rzarev@caltech.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
drivers/pci/quirks.c | 6 ++++++
1 file changed, 6 insertions(+)
--- gregkh-2.6.orig/drivers/pci/quirks.c 2005-09-09 10:28:55.000000000 -0700
+++ gregkh-2.6/drivers/pci/quirks.c 2005-09-09 13:51:44.000000000 -0700
@@ -876,6 +876,12 @@ static void __init asus_hides_smbus_host
case 0xC00C: /* Samsung P35 notebook */
asus_hides_smbus = 1;
}
+ } else if (unlikely(dev->subsystem_vendor == PCI_VENDOR_ID_COMPAQ)) {
+ if (dev->device == PCI_DEVICE_ID_INTEL_82855PM_HB)
+ switch(dev->subsystem_device) {
+ case 0x0058: /* Compaq Evo N620c */
+ asus_hides_smbus = 1;
+ }
}
}
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82845_HB, asus_hides_smbus_hostbridge );
Share code between setup-bus.c and yenta_socket.c: use the write-out code of
resources to the bridge also in yenta_socket.c, as it provides useful debug
output. In addition, it fixes the bug that the CPU-centric resource view
might need to be transferred to the PCI-centric view: setup-bus.c does that,
while yenta-socket.c did not.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This fixes a bug in the environment variables for all PCI device hotplug calls.
Thanks to Kay Sievers for pointing out the problem.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Previous INTx cleanup patch had a bug that was not caught. I found
this last night during testing and can confirm that it is now 100%
working.
Signed-off-by: Brett Russ <russb@emc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch pulls the PCI-related junk out of struct device_node and
puts it in a separate structure, struct pci_dn. The device_node now
just has a void * pointer in it, which points to a struct pci_dn for
nodes that represent PCI devices. It could potentially be used in
future for device-specific data for other sorts of devices, such as
virtual I/O devices.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Simple cleanup to eliminate X copies of the pci_enable_intx() function
in libata. Moved ahci.c's pci_intx() to pci.c and use it throughout
libata and msi.c.
Signed-off-by: Brett Russ <russb@emc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- support PCI PM CAP version 3 (as defined in PCI PM Interface Spec v1.2)
- pci/probe.c sets the PM state initially to 4 which is D3cold. add a
PCI_UNKNOWN
- minor cleanups
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The PCI error recovery infrastructure needs to be able to contact all
the drivers affected by a PCI error event, which may mean traversing
all the devices under a given PCI-PCI bridge. This patch adds a
function to the PCI core that traverses all the PCI devices on a PCI
bus and under any PCI-PCI bridges on that bus (and so on), calling a
given function for each device. This provides a way for the error
recovery code to iterate through all devices that are affected by an
error event.
This version is not implemented as a recursive function. Instead,
when we reach a PCI-PCI bridge, we set the pointers to start doing the
devices on the bus under the bridge, and when we reach the end of a
bus's devices, we use the bus->self pointer to go back up to the next
higher bus and continue doing its devices.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
These fixes were suggested by pcihpd-discuss, but were dropped in the
initial checkin of the code. These fixes include cleaning up the
hotplug driver sysfs filename, and some minor code cleanups. The driver
also requires at least PROM 4.30, not 4.20.
Signed-off-by: Prarit Bhargava <prarit@sgi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as552) fixes yet another small problem recently added. If an
attempt to put a PCI device back into D0 fails because the device doesn't
support PCI PM, it shouldn't count as error. Without this patch the UHCI
controllers on my Intel motherboard don't work.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There were three changes necessary in order to allow
sparc64 to use setup-res.c:
1) Sparc64 roots the PCI I/O and MEM address space using
parent resources contained in the PCI controller structure.
I'm actually surprised no other platforms do this, especially
ones like Alpha and PPC{,64}. These resources get linked into the
iomem/ioport tree when PCI controllers are probed.
So the hierarchy looks like this:
iomem --|
PCI controller 1 MEM space --|
device 1
device 2
etc.
PCI controller 2 MEM space --|
...
ioport --|
PCI controller 1 IO space --|
...
PCI controller 2 IO space --|
...
You get the idea. The drivers/pci/setup-res.c code allocates
using plain iomem_space and ioport_space as the root, so that
wouldn't work with the above setup.
So I added a pcibios_select_root() that is used to handle this.
It uses the PCI controller struct's io_space and mem_space on
sparc64, and io{port,mem}_resource on every other platform to
keep current behavior.
2) quirk_io_region() is buggy. It takes in raw BUS view addresses
and tries to use them as a PCI resource.
pci_claim_resource() expects the resource to be fully formed when
it gets called. The sparc64 implementation would do the translation
but that's absolutely wrong, because if the same resource gets
released then re-claimed we'll adjust things twice.
So I fixed up quirk_io_region() to do the proper pcibios_bus_to_resource()
conversion before passing it on to pci_claim_resource().
3) I was mistakedly __init'ing the function methods the PCI controller
drivers provide on sparc64 to implement some parts of these
routines. This was, of course, easy to fix.
So we end up with the following, and that nasty SPARC64 makefile
ifdef in drivers/pci/Makefile is finally zapped.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some PCI devices (e.g. 3c905B, 3c556B) lose all configuration
(including BARs) when transitioning from D3hot->D0. This leaves such
a device in an inaccessible state. The patch below causes the BARs
to be restored when enabling such a device, so that its driver will
be able to access it.
The patch also adds pci_restore_bars as a new global symbol, and adds a
correpsonding EXPORT_SYMBOL_GPL for that.
Some firmware (e.g. Thinkpad T21) leaves devices in D3hot after a
(re)boot. Most drivers call pci_enable_device very early, so devices
left in D3hot that lose configuration during the D3hot->D0 transition
will be inaccessible to their drivers.
Drivers could be modified to account for this, but it would
be difficult to know which drivers need modification. This is
especially true since often many devices are covered by the same
driver. It likely would be necessary to replicate code across dozens
of drivers.
The patch below should trigger only when transitioning from D3hot->D0
(or at boot), and only for devices that have the "no soft reset" bit
cleared in the PM control register. I believe it is safe to include
this patch as part of the PCI infrastructure.
The cleanest implementation of pci_restore_bars was to call
pci_update_resource. Unfortunately, that does not currently exist
for the sparc64 architecture. The patch below includes a null
implemenation of pci_update_resource for sparc64.
Some have expressed interest in making general use of the the
pci_restore_bars function, so that has been exported to GPL licensed
modules.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
For systems with multiple hotplug controllers, you need to use more than
just the slot number to uniquely name the slot. Without a unique slot
name, the pci_hp_register() will fail. This patch adds the bus number
to the name.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Run PCI driver initialization on local node
Instead of adding messy kmalloc_node()s everywhere run the
PCI driver probe on the node local to the device.
This would not have helped for IDE, but should for
other more clean drivers that do more initialization in probe().
It won't help for drivers that do most of the work
on first open (like many network drivers)
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently rpaphp registers the following bus types as hotplug slots:
1) Actual PCI Hotplug slots
2) Embedded/Internal PCI slots
3) PCI Host Bridges
The second and third bus types are not actually direct parents of
removable adapters. As such, the rpaphp has special case code to fake
results for attributes like power, adapter status, etc. This patch
removes types 2 and 3 from the rpaphp module.
This patch also changes the DLPAR module so that slots can be
DLPAR-added/removed without having been designated as hotplug-capable.
Signed-off-by: John Rose <johnrose@austin.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch exports rpaphp_config_pci_adapter() for use by the rpadlpar
module. It also changes this function by removing any dependencies on
struct slot. The patch also changes the RPA DLPAR-add path to enable
newly-added slots in a separate step from that which registers them as
hotplug slots.
Signed-off-by: John Rose <johnrose@austin.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The rpaphp module currently uses a fragile method to find a pci device
by its device node. This function is unnecessary, so this patch scraps
it.
Signed-off-by: John Rose <johnrose@austin.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The slot structure in the rpaphp module currently references the PCI
contents of the slot using the PCI device of the parent bridge. This
is unnecessary, since the module is actually interested in the
subordinate bus of the bridge. The dependency on a PCI bridge device
also prohibits the module from registering hotplug slots that have a
root bridge as a parent, since root bridges on PPC64 don't have PCI
devices.
This patch changes struct slot to reference the PCI subsystem using a
pci_bus rather than a pci_dev.
Signed-off-by: John Rose <johnrose@austin.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently, rpaphp registers Virtual I/O slots as hotplug slots. The
only purpose of this registration is to ensure that the VIO subsystem
is notified of new VIO buses during DLPAR adds. Similarly, rpaphp
notifies the VIO subsystem when a VIO bus is DLPAR-removed. The rpaphp
module has special case code to fake results for attributes like power,
adapter status, etc.
The VIO register/unregister functions could just as easily be made from
the DLPAR module. This patch moves the VIO registration calls to the
DLPAR module, and removes the VIO fluff from rpaphp altogether.
Signed-off-by: John Rose <johnrose@austin.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When handling writes to /proc/irq, current code is re-programming rte
entries directly. This is not recommended and could potentially cause
chipset's to lockup, or cause missing interrupts.
CONFIG_IRQ_BALANCE does this correctly, where it re-programs only when the
interrupt is pending. The same needs to be done for /proc/irq handling as well.
Otherwise user space irq balancers are really not doing the right thing.
- Changed pending_irq_balance_cpumask to pending_irq_migrate_cpumask for
lack of a generic name.
- added move_irq out of IRQ_BALANCE, and added this same to X86_64
- Added new proc handler for write, so we can do deferred write at irq
handling time.
- Display of /proc/irq/XX/smp_affinity used to display CPU_MASKALL, instead
it now shows only active cpu masks, or exactly what was set.
- Provided a common move_irq implementation, instead of duplicating
when using generic irq framework.
Tested on i386/x86_64 and ia64 with CONFIG_PCI_MSI turned on and off.
Tested UP builds as well.
MSI testing: tbd: I have cards, need to look for a x-over cable, although I
did test an earlier version of this patch. Will test in a couple days.
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Acked-by: Zwane Mwaikambo <zwane@holomorphy.com>
Grudgingly-acked-by: Andi Kleen <ak@muc.de>
Signed-off-by: Coywolf Qi Hunt <coywolf@lovecn.org>
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This adds type-checking to pm_message_t, so that people can't confuse it
with int or u32. It also allows us to fix "disk yoyo" during suspend (disk
spinning down/up/down).
[We've tried that before; since that cpufreq problems were fixed and I've
tried make allyes config and fixed resulting damage.]
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Alexander Nyberg <alexn@telia.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The VIA VT8237's IOAPIC sends 'APIC De-Assert Messages' by default, causing
another CPU interrupt when the IRQ pin is de-asserted. This feature is
switched off by the patch to get rid of doubled ioapic level interrupt
rates.
Signed-off-by: Karsten Wiese <annabellesgarden@yahoo.de>
Tested-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This fixes a problem with pci_map_rom() which doesn't properly
update the ROM BAR value with the address thas allocated for it by the
PCI code. This problem, among other, breaks boot on Mac laptops.
It'ss a new version based on Linus latest one with better error
checking.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I had some time to think about PCI assign issues in 2.6.13-rc series.
The major problem here is that we call pci_assign_unassigned_resources()
way too early - at subsys_initcall level. Therefore we give no chances
to ACPI and PnP routines (called at fs_initcall level) to reserve their
respective resources properly, as the comments in drivers/pnp/system.c
and drivers/acpi/motherboard.c suggest:
/**
* Reserve motherboard resources after PCI claim BARs,
* but before PCI assign resources for uninitialized PCI devices
*/
So I moved the pci_assign_unassigned_resources() call to
pcibios_assign_resources() (fs_initcall), which should hopefully fix a
lot of problems and make PCIBIOS_MIN_IO tweaks unnecessary.
Other changes:
- remove resource assignment code from pcibios_assign_resources(), since
it duplicates pci_assign_unassigned_resources() functionality and
actually does nothing in 2.6.13;
- modify ROM assignment code as per Ben's suggestion: try to use firmware
settings by default (if PCI_ASSIGN_ROMS is not set);
- set CARDBUS_IO_SIZE back to 4K as it's a wonderful stress test for
various setups.
Confirmed by Tero Roponen <teanropo@cc.jyu.fi> (who had problems with
the 4kB CardBus IO size previously).
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Writing even a disabled value seems to mess up some matrox graphics
cards. It may be a card-related issue, but we may also be writing
reserved low bits in the result.
This was a fall-out of switching x86 over to the generic PCI resource
allocation code, and needs more debugging. In particular, the old x86
code defaulted to not doing any resource allocations at all for ROM
resources.
In the meantime, this has been reported to make X happier by Helge
Hafting <helgehaf@aitel.hist.no>.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It may seem small, but most cards need much less, if any, and this not
only makes the code adhere to the comment, it seems to fix a boot-time
lockup on a ThinkPad 380XD laptop reported by Tero Roponen <teanropo@cc.jyu.fi>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
On the 6700/6702 PXH part, a MSI may get corrupted if an ACPI hotplug
driver and SHPC driver in MSI mode are used together.
This patch will prevent MSI from being enabled for the SHPC as part of
an early pci quirk, as well as on any pci device which sets the no_msi
bit.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Revert commit fec59a711e, which is
breaking sparc64 that doesn't have a working pci_update_resource.
We'll re-do this after 2.6.13 when we'll do it all properly.
Like many other southbridges from different manufacturers, VIA VT8235
chip has two non-standard BARs for power management and SMBus registers
(see the datasheet at http://www.via.com.tw).
This new quirk routine fixes boot problem with 2.6.13-rc2/rc6 kernels on
Targa Visionary 811 Athlon64 laptop, as reported by Mikael Pettersson
<mikpe@csd.uu.se>.
Signed-off-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
For 64-bit BAR[i] only pci_dev->resource[i] is valid, ->resource[i+1]
slot is unused and contains zeroes in all fields.
So when we update a PCI BAR, all we need is just to check that we're
going to update a _valid_ resource.
Also make sure to write high bits - use "x >> 16 >> 16" (rather than the
simpler ">> 32") to avoid warnings on 32-bit architectures where we're
not going to have any high bits.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some PCI devices (e.g. 3c905B, 3c556B) lose all configuration
(including BARs) when transitioning from D3hot->D0. This leaves such
a device in an inaccessible state. The patch below causes the BARs
to be restored when enabling such a device, so that its driver will
be able to access it.
The patch also adds pci_restore_bars as a new global symbol, and adds a
correpsonding EXPORT_SYMBOL_GPL for that.
Some firmware (e.g. Thinkpad T21) leaves devices in D3hot after a
(re)boot. Most drivers call pci_enable_device very early, so devices
left in D3hot that lose configuration during the D3hot->D0 transition
will be inaccessible to their drivers.
Drivers could be modified to account for this, but it would
be difficult to know which drivers need modification. This is
especially true since often many devices are covered by the same
driver. It likely would be necessary to replicate code across dozens
of drivers.
The patch below should trigger only when transitioning from D3hot->D0
(or at boot), and only for devices that have the "no soft reset" bit
cleared in the PM control register. I believe it is safe to include
this patch as part of the PCI infrastructure.
The cleanest implementation of pci_restore_bars was to call
pci_update_resource. Unfortunately, that does not currently exist
for the sparc64 architecture. The patch below includes a null
implemenation of pci_update_resource for sparc64.
Some have expressed interest in making general use of the the
pci_restore_bars function, so that has been exported to GPL licensed
modules.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The reason we have PCIBIOS_MIN_IO and PCIBIOS_MIN_CARDBUS_IO is because
we want to protect badly documented motherboard PCI resources and thus
don't want to allocate new resources in low IO/MEM space.
However, if we have already discovered a PCI bridge with a specified
resource base, that should override that decision.
This change will allow us to move the "careful" region upwards without
resulting in problems allocating resources in low mappings. This was
brought on by us having allocated a bus resource at 0x1000, conflicting
with a undocumented VAIO Sony PI resources.
