The U8540 was an evolved version of the U8500, but it was never
mass produced or put into products, only reference designs exist.
The upstream support was never completed and it is unlikely that
this will happen so drop the support for now to simplify
maintenance of the U8500.
Cc: Loic Pallardy <loic.pallardy@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- Add USB pin groups on R-Car M3-N,
- Add support for the new R-Car V3H SoC,
- Add EtherAVB pin groups on R-Car V3M,
- Miscellaneous fixes and cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=swQl
-----END PGP SIGNATURE-----
Merge tag 'sh-pfc-for-v4.17-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel
pinctrl: sh-pfc: Updates for v4.17 (take two)
- Add USB pin groups on R-Car M3-N,
- Add support for the new R-Car V3H SoC,
- Add EtherAVB pin groups on R-Car V3M,
- Miscellaneous fixes and cleanups.
Use union vin_data and VIN_DATA_PIN_GROUP() to reduce redundancies
in pin definitions.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Use union vin_data and VIN_DATA_PIN_GROUP() to reduce redundancies
in pin definitions.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Use union vin_data and VIN_DATA_PIN_GROUP() to reduce redundancies
in pin definitions.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
RGB666 has a pin assignment that differs from the other formats.
Fixes: fbd452aeb4 ("pinctrl: sh-pfc: r8a77995: Add VIN4 pins, groups and function")
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
RGB666 has a pin assignment that differs from the other formats.
Fixes: 8db6cbabac ("pinctrl: sh-pfc: r8a7796: Add VIN4, VIN5 pins, groups and functions")
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
RGB666 has a pin assignment that differs from the other formats.
Fixes: 6b4de40810 ("pinctrl: sh-pfc: r8a7795: Add VIN4, VIN5 pins, groups and functions")
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
On other Renesas SoCs, the pin group for the MDIO bus is named "mdio"
instead of "mdc". Fix the inconsistency, while retaining backwards
compatibility with old DTBs using a pin group alias.
Fixes: 66abd968d0 ("pinctrl: sh-pfc: r8a77995: Add EthernetAVB pins, groups and functions")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
On other Renesas SoCs, the pin group for the MDIO bus is named "mdio"
instead of "mdc". Fix the inconsistency, while retaining backwards
compatibility with old DTBs using a pin group alias.
Fixes: fa3e8b71b9 ("pinctrl: sh-pfc: r8a77965: Add EtherAVB groups/functions")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
On other Renesas SoCs, the pin group for the MDIO bus is named "mdio"
instead of "mdc". Fix the inconsistency, while retaining backwards
compatibility with old DTBs using a pin group alias.
Fixes: 41397032c4 ("pinctrl: sh-pfc: r8a7796: Add group for AVB MDIO and MII pins")
Fixes: 9c99a63ec7 ("pinctrl: sh-pfc: r8a7796: Add EtherAVB pins, groups and functions")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
On other Renesas SoCs, the pin group for the MDIO bus is named "mdio"
instead of "mdc". Fix the inconsistency, while retaining backwards
compatibility with old DTBs using a pin group alias.
Fixes: b25719eb93 ("pinctrl: sh-pfc: r8a7795: Add group for AVB MDIO and MII pins")
Fixes: 819fd4bfcc ("pinctrl: sh-pfc: r8a7795: add EtherAVB support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
On other Renesas SoCs, the pin group for the MDIO bus is named "mdio"
instead of "mdc". Fix the inconsistency, while retaining backwards
compatibility with old DTBs using a pin group alias.
Fixes: 30c078de6f ("pinctrl: sh-pfc: r8a7795: Add EtherAVB pins, groups and function")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Add a macro to refer to another pin group with a different name.
This will be used to rename wrongly-named pin groups, while retaining
backwards compatibility with old DTBs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
The pin controller drivers for all R-Car Gen2 SoCs have entries for the
EtherAVB TX_ER pins in their EtherAVB MII groups, except on R-Car H2.
Add the missing pin to restore consistency.
Note that technically TX_ER is an optional signal in the MII bus, and
thus could have its own group, but this is currently not supported by
any R-Car Gen2 pin controller driver.
Fixes: 19ef697d1e ("sh-pfc: r8a7790: add EtherAVB pin groups")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Add the EtherAVB pin groups to the R8A77970 PFC driver.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add the PFC support for the R8A77980 SoC including pin groups for some
on-chip devices such as AVB, CAN-FD, GETHER, [H]SCIF, I2C, INTC-EX, MMC,
MSIOF, PWM, and VIN...
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
They follow the style of the existing PORT_GP_CFG_<n>() macros and
will be used by a follow-up patch for the R8A77980 SoC.
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds USB30 (USB3.0 host) pin, group and function to
the R8A77965 SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
- Add DU and VIN pin groups on R-Car D3,
- Add HDMI, TMU, and VIN pin groups on R-Car H3 and M3-W,
- Add support for the new R-Car M3-N SoC,
- Small fixes and cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=mYK2
-----END PGP SIGNATURE-----
Merge tag 'sh-pfc-for-v4.17-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel
pinctrl: sh-pfc: Updates for v4.17
- Add DU and VIN pin groups on R-Car D3,
- Add HDMI, TMU, and VIN pin groups on R-Car H3 and M3-W,
- Add support for the new R-Car M3-N SoC,
- Small fixes and cleanups.
Systems that don't have devicetree need pinctrl_register_mappings.
It should be EXPORT_SYMBOL_GPL so that it can be called from
pinctrl drivers built as modules.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Meson8b is a cost reduced variant of the Meson8 SoC. It's package size
is smaller than Meson8.
Unfortunately there are a few key differences which cannot be seen
without close inspection of the code and the public S805 datasheet:
- the GPIOX bank is missing the GPIOX_12, GPIOX_13, GPIOX_14 and
GPIOX_15 GPIOs
- the GPIOY bank is missing the GPIOY_2, GPIOY_4, GPIOY_5, GPIOY_15 and
GPIOY_16 GPIOs
- the GPIODV bank is missing all GPIOs except GPIODV_9, GPIODV_24,
GPIODV_25, GPIODV_26, GPIODV_27, GPIODV_28 and GPIODV_29
- the GPIOZ bank is missing completely
- there is a new GPIO bank called "DIF"
This means that Meson8b only has 83 actual GPIO lines. Without any holes
there would be 130 GPIO lines in total (120 are inherited from Meson8
plus 10 new from the DIF bank).
GPIOs greater GPIOZ_3 (whose ID is 83 - as a reminder: this is exactly
the number of actual GPIO lines on Meson8b and also the value of
meson8b_cbus_pinctrl_data.num_pins) cannot berequested. Using CARD_6
(which used ID 100 prior to this patch, "base of the GPIO controller was
382) as an example:
$ echo 482 > /sys/class/gpio/export
export_store: invalid GPIO 482
This removes all non-existing pins from to dt-bindings header file
(include/dt-bindings/gpio/meson8b-gpio.h). This allows us to have a
consecutive numbering for the GPIO #defines (GPIOY_2 doesn't exist for
example, so previously the GPIOY_3 ID was "GPIOY_1 + 2", after this
patch it is "GPIOY_1 + 1"). As a nice side-effect this means that we get
compile-time (instead of runtime) errors if Meson8b .dts uses a pin that
only exists on Meson8.
Additionally the pinctrl-meson8b driver has to be updated to handle this
new GPIO numbering. By default a struct meson_bank only handles GPIO
banks where the pins are numbered consecutively because it calculates
the bit offsets based on the GPIO IDs.
This is solved by taking the original BANK() definition and splitting it
into consecutive subsets (X0..11 and X16..21). The bit offsets for each
new bank includes the skipped GPIOs (the definition of the "X0..11" bank
is identical to the old "X" bank apart from the "last IRQ" field, the
definition of the new, split "X16..21" bank takes the original "X" bank
and adds 16 - the start of the new split bank - to the "first IRQ",
pullen bit, pull bit, dir bit, out bit and in bit).
Commit 984cffdeae ("pinctrl: Fix gpio/pin mapping for Meson8b")
fixed the same issue by setting "ngpio" (of the gpio_chip) to 130.
Unfortunately this broke in db80f0e158 ("pinctrl: meson: get rid of
unneeded domain structures").
The solution from this patch was considered to be better than the
previous attempt at fixing this because it provides compile-time error
checking for the GPIOs that exist on Meson8 but don't exist on Meson8b.
The following pins were tested on an Odroid-C1 using the sysfs GPIO
interface checking that their value (high or low) could be read:
- GPIOX_0, GPIOX_1, GPIOX_2, GPIOX_3, GPIOX_4, GPIOX_5, GPIOX_6,
GPIOX_7, GPIOX_8, GPIOX_9, GPIOX_10, GPIOX_11, GPIOX_18, GPIOX_19,
GPIOX_20, GPIOX_21
- GPIOY_3, GPIOY_7, GPIOY_8
(some of these had to be pulled up because they were low by default,
others were high by default so these had to be pulled down)
Reported-by: Linus Lüssing <linus.luessing@c0d3.blue>
Suggested-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When dt_to_map_one_config() is called with a pinctrl_dev passed
in, it should only be using this if the node being looked up
is a hog. The code was always using the passed pinctrl_dev
without checking whether the dt node referred to it.
A pin controller can have pinctrl-n dependencies on other pin
controllers in these cases:
- the pin controller hardware is external, for example I2C, so
needs other pin controller(s) to be setup to communicate with
the hardware device.
- it is a child of a composite MFD so its of_node is shared with
the parent MFD and other children of that MFD. Any part of that
MFD could have dependencies on other pin controllers.
Because of this, dt_to_map_one_config() can't assume that if it
has a pinctrl_dev passed in then the node it looks up must be
a hog. It could be a reference to some other pin controller.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add group configuration for uarts that are cut down
variants, the standard being full, i.e. all signals,
flow control, i.e. rx/tx and cts/rts, and rx/tx only.
This allows us to be more precise in which pins we're
actually using.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Now that arch/metag/ has been removed, along with TZ1090 SoC support,
remove the TZ1090 pinctrl drivers. They are of no value without the
architecture and SoC platform code.
Signed-off-by: James Hogan <jhogan@kernel.org>
Cc: linux-gpio@vger.kernel.org
Cc: linux-metag@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Most pins on the R8A77965 SoC can be configured in GPIO mode for
interrupt and GPIO functionality, while a couple of them can also
be routed to the INTC-EX hardware block (formerly known as IRQC).
On R8A77965 the INTC-EX hardware handles pins IRQ0 -> IRQ5 and
this patch adds support for them to the PFC driver as "intc_ex_irqN".
Based on a similar patch for the R8A7795 PFC driver by Magnus Damm
<damm+renesas@opensource.se>.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds VIN4 pins, groups and function for the
R8A77995 (D3) SoC.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds VIN4 and VIN5 pins, groups and functions for the
R8A7795 SoC.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds VIN4 and VIN5 pins, groups and functions for the
R8A7796 SoC.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The mcp23s08 series device can be configured for wired and interrupts
using an external pull-up and open drain output via the IOCON_ODR bit.
And "drive-open-drain" property to enable this.
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Phil Reid <preid@electromag.com.au>
Reviewed-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
one_regmap_config is always null if mcp type is MCP_TYPE_S18.
Remove the null check so that the mcp23s18 will probe.
Fixes: 1781af563a ("pinctrl: mcp23s08: spi: Fix duplicate pinctrl debugfs entries")
Signed-off-by: Phil Reid <preid@electromag.com.au>
Reviewed-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On boot, gpiochip_add_data() initializes the FLAG_IS_OUT bit in
desc->flags iff its gpio_chip does not have ->direction_input() handler,
else it is initialized to 0, which implies the GPIO is an "input".
Later, the sysfs "direction" handler will use gpiod_get_direction() to
get the current direction, but if no ->get_direction() handler is
installed, the result will just be the current (initial) value of flags,
which will always be OUT irregardless of the initial register value.
Add a get_direction() handler to pinctrl-amd to fix this and always
provide the correct value for direction.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
...instead of open coding file operations followed by custom ->open()
callbacks per each attribute.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The function ocelot_pinctrl_probe is local to the source and does not
need to be in global scope, so make it static.
Cleans up sparse warning:
drivers/pinctrl/pinctrl-ocelot.c:465:5: warning: symbol
'ocelot_pinctrl_probe' was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add SCIF[0-5] groups and pin function definitions for R-Car M3-N.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add initial PFC support for R-Car M3-N (r8a77965) SoC.
No groups or functions defined, just pin and registers enumeration.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds TMU TCLK{1,2} pins, groups and functions to
the R8A7796 SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds TMU TCLK{1,2} pins, groups and functions to
the R8A7795 ES1.x SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds TMU TCLK{1,2} pins, groups and functions to
the R8A7795 SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds HDMI0 CEC pin, group and function to the R8A7796 SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds HDMI0 CEC pin, group and function to
the R8A7795 ES1.x SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[uli: fixed typo in comment]
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds HDMI0 CEC pin, group and function to the R8A7795 SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[uli: fixed typo in comment]
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch fixes to set IPSR and MOD_SEL when using NFDATA{14,15}_A and
NF{RB,WP}_N_A pin function is selected. And renamess MOD_SEL2 bit22 value
definition name to SEL_NDFC.
This is a correction to the incorrect implementation of MOD_SEL register
pin assignment for R8A7796 SoC specification of R-Car Gen3 Hardware
User's Manual Rev.0.53E.
Fixes: f9aece7344 ("pinctrl: sh-pfc: Initial R8A7796 PFC support")
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch fixes MOD_SEL1 bit20 and MOD_SEL2 bit20, bit21 pin assignment
for SSI pins group.
This is a correction to the incorrect implementation of MOD_SEL register
pin assignment for R8A7796 SoC specification of R-Car Gen3 Hardware
User's Manual Rev.0.51E or later.
Fixes: f9aece7344 ("pinctrl: sh-pfc: Initial R8A7796 PFC support")
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch fixes MOD_SEL1 bit20 and MOD_SEL2 bit20, bit21 pin assignment
for SSI pins group.
This is a correction because MOD_SEL register specification for R8A7795
ES2.0 SoC was changed in R-Car Gen3 Hardware User's Manual Rev.0.53E.
Fixes: b205914c8f ("pinctrl: sh-pfc: r8a7795: Add support for R-Car H3 ES2.0")
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds DU pins, groups and function for the R8A77995 (D3) SoC.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The MUSB block in the Nomadik has two pin settings: high speed or
full speed. These correspond to two unique pin group settings: all
pins set to function B for high speed and all set to function C
for full speed. Full speed uses more pins than high speed.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
