There are two reasons for reporting wakeup event when dedicated wakeup
IRQ is triggered:
- wakeup events accounting, so proper statistical data will be
displayed in sysfs and debugfs;
- there are small window when System is entering suspend during which
dedicated wakeup IRQ can be lost:
dpm_suspend_noirq()
|- device_wakeup_arm_wake_irqs()
|- dev_pm_arm_wake_irq(X)
|- IRQ is enabled and marked as wakeup source
[1]...
|- suspend_device_irqs()
|- suspend_device_irq(X)
|- irqd_set(X, IRQD_WAKEUP_ARMED);
|- wakup IRQ armed
The wakeup IRQ can be lost if it's triggered at point [1]
and not armed yet.
Hence, fix above cases by adding simple pm_wakeup_event() call in
handle_threaded_wake_irq().
Fixes: 4990d4fe32 (PM / Wakeirq: Add automated device wake IRQ handling)
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
[ tony@atomide.com: added missing return to avoid warnings ]
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Dedicated wakeirq is a one time event to wake-up the system from
low-power state and then call pm_runtime_resume() on the device wired
with the dedicated wakeirq.
Sometimes dedicated wakeirqs can get deferred if they trigger after we
call disable_irq_nosync() in dev_pm_disable_wake_irq(). This can happen
if pm_runtime_get() is called around the same time a wakeirq fires.
If an interrupt fires after disable_irq_nosync(), by default it will get
tagged with IRQS_PENDING and will run later on when the interrupt is
enabled again.
Deferred wakeirqs usually just produce pointless wake-up events. But they
can also cause suspend to fail if the deferred wakeirq fires during
dpm_suspend_noirq() for example. So we really don't want to see the
deferred wakeirqs triggering after the device has resumed.
Let's fix the issue by setting IRQ_DISABLE_UNLAZY flag for the dedicated
wakeirqs. The other option would be to implement irq_disable() in the
dedicated wakeirq controller, but that's not a generic solution.
For reference below is what happens with a IRQ_TYPE_EDGE_BOTH IRQ
type wakeirq:
- resume by dedicated IRQ (EDGE_FALLING)
- suspend_enter()
....
- arch_suspend_enable_irqs()
|- dedicated IRQ armed and fired
|- irq_pm_check_wakeup()
|- disarm, disable IRQ and mark as IRQS_PENDING
....
- dpm_resume_noirq()
|- resume_device_irqs()
|- __enable_irq()
|- check_irq_resend()
|- handle_threaded_wake_irq()
|- dedicated IRQ processed
|- device_wakeup_disarm_wake_irqs()
|- disable_irq_wake()
....
!-> dedicated IRQ (EDGE_RISING)
-| handle_edge_irq()
|- IRQ disabled: mask_ack_irq and mark as IRQS_PENDING
....
- subsequent suspend
....
|- dpm_suspend_noirq()
|- device_wakeup_arm_wake_irqs()
|- __enable_irq()
|- check_irq_resend()
(a) |- handle_threaded_wake_irq()
|- pm_wakeup_event() --> abort suspend
....
|- suspend_device_irqs()
|- suspend_device_irq()
|- dedicated IRQ armed
....
(b) |- resend_irqs
|- irq_pm_check_wakeup()
|- IRQ armed -> abort suspend
because of pending IRQ System suspend can be aborted at points
(a)-not armed or (b)-armed.
Fixes: 4990d4fe32 (PM / Wakeirq: Add automated device wake IRQ handling)
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
[ tony@atomide.com: added a comment, updated the description ]
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
We currently rely on runtime PM to enable dedicated wakeirq for suspend.
This assumption fails in the following two cases:
1. If the consumer driver does not have runtime PM implemented, the
dedicated wakeirq never gets enabled for suspend
2. If the consumer driver has runtime PM implemented, but does not idle
in suspend
Let's fix the issue by always enabling the dedicated wakeirq during
suspend.
Depends-on: bed570307e (PM / wakeirq: Fix dedicated wakeirq for drivers not using autosuspend)
Fixes: 4990d4fe32 (PM / Wakeirq: Add automated device wake IRQ handling)
Reported-by: Keerthy <j-keerthy@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
[ tony@atomide.com: updated based on bed570307e, added description ]
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Rename _of_get_opp_desc_node to dev_pm_opp_of_get_opp_desc_node and add it
to include/linux/pm_opp.h to allow other drivers, such as platform OPP
and cpufreq drivers, to make use of it.
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
As the PM core may invoke the *noirq() callbacks asynchronously, the
current lock-less approach in genpd doesn't work. The consequence is that
we may find concurrent operations racing to power on/off the PM domain.
As of now, no immediate errors has been reported, but it's probably only a
matter time. Therefor let's fix the problem now before this becomes a real
issue, by deploying the locking scheme to the relevant functions.
Reported-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The earlier comment stated that the dev_warn_once() was going to be printed
once per device. Let's fix that, as dev_warn_once() is printed only once,
no matter of the device.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Lina Iyer <lina.iyer@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Fixes the following sparse warning:
drivers/base/power/opp/core.c:49:18: warning:
symbol '_find_opp_table_unlocked' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The might_sleep_if() assertions in __pm_runtime_idle(),
__pm_runtime_suspend() and __pm_runtime_resume() may generate
false-positive warnings in some situations. For example, that
happens if a nested pm_runtime_get_sync()/pm_runtime_put() pair
is executed with disabled interrupts within an outer
pm_runtime_get_sync()/pm_runtime_put() section for the same device.
[Generally, pm_runtime_get_sync() may sleep, so it should not be
called with disabled interrupts, but in this particular case the
previous pm_runtime_get_sync() guarantees that the device will not
be suspended, so the inner pm_runtime_get_sync() will return
immediately after incrementing the device's usage counter.]
That started to happen in the i915 driver in 4.10-rc, leading to
the following splat:
BUG: sleeping function called from invalid context at drivers/base/power/runtime.c:1032
in_atomic(): 1, irqs_disabled(): 0, pid: 1500, name: Xorg
1 lock held by Xorg/1500:
#0: (&dev->struct_mutex){+.+.+.}, at:
[<ffffffffa0680c13>] i915_mutex_lock_interruptible+0x43/0x140 [i915]
CPU: 0 PID: 1500 Comm: Xorg Not tainted
Call Trace:
dump_stack+0x85/0xc2
___might_sleep+0x196/0x260
__might_sleep+0x53/0xb0
__pm_runtime_resume+0x7a/0x90
intel_runtime_pm_get+0x25/0x90 [i915]
aliasing_gtt_bind_vma+0xaa/0xf0 [i915]
i915_vma_bind+0xaf/0x1e0 [i915]
i915_gem_execbuffer_relocate_entry+0x513/0x6f0 [i915]
i915_gem_execbuffer_relocate_vma.isra.34+0x188/0x250 [i915]
? trace_hardirqs_on+0xd/0x10
? i915_gem_execbuffer_reserve_vma.isra.31+0x152/0x1f0 [i915]
? i915_gem_execbuffer_reserve.isra.32+0x372/0x3a0 [i915]
i915_gem_do_execbuffer.isra.38+0xa70/0x1a40 [i915]
? __might_fault+0x4e/0xb0
i915_gem_execbuffer2+0xc5/0x260 [i915]
? __might_fault+0x4e/0xb0
drm_ioctl+0x206/0x450 [drm]
? i915_gem_execbuffer+0x340/0x340 [i915]
? __fget+0x5/0x200
do_vfs_ioctl+0x91/0x6f0
? __fget+0x111/0x200
? __fget+0x5/0x200
SyS_ioctl+0x79/0x90
entry_SYSCALL_64_fastpath+0x23/0xc6
even though the code triggering it is correct.
Unfortunately, the might_sleep_if() assertions in question are
too coarse-grained to cover such cases correctly, so make them
a bit less sensitive in order to avoid the false-positives.
Reported-and-tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
dev_pm_opp_get_max_volt_latency() calls _find_opp_table() two times
effectively.
Merge _get_regulator_count() into dev_pm_opp_get_max_volt_latency() to
avoid that.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
As we don't use RCU locking anymore, there is no need to replace an
earlier OPP node with a new one. Just update the existing one.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The RCU locking isn't well suited for the OPP core. The RCU locking fits
better for reader heavy stuff, while the OPP core have at max one or two
readers only at a time.
Over that, it was getting very confusing the way RCU locking was used
with the OPP core. The individual OPPs are mostly well handled, i.e. for
an update a new structure was created and then that replaced the older
one. But the OPP tables were updated directly all the time from various
parts of the core. Though they were mostly used from within RCU locked
region, they didn't had much to do with RCU and were governed by the
mutex instead.
And that mixed with the 'opp_table_lock' has made the core even more
confusing.
Now that we are already managing the OPPs and the OPP tables with kernel
reference infrastructure, we can get rid of RCU locking completely and
simplify the code a lot.
Remove all RCU references from code and comments.
Acquire opp_table->lock while parsing the list of OPPs though.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Take reference of the OPP table from within _find_opp_table(). Also
update the callers of _find_opp_table() to call
dev_pm_opp_put_opp_table() after they have used the OPP table.
Note that _find_opp_table() increments the reference under the
opp_table_lock.
Now that the OPP table wouldn't get freed until the callers of
_find_opp_table() call dev_pm_opp_put_opp_table(), there is no need to
take the opp_table_lock or rcu_read_lock() around it. Drop them.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch updates dev_pm_opp_find_freq_*() routines to get a reference
to the OPPs returned by them.
Also updates the users of dev_pm_opp_find_freq_*() routines to call
dev_pm_opp_put() after they are done using the OPPs.
As it is guaranteed the that OPPs wouldn't get freed while being used,
the RCU read side locking present with the users isn't required anymore.
Drop it as well.
This patch also updates all users of devfreq_recommended_opp() which was
returning an OPP received from the OPP core.
Note that some of the OPP core routines have gained
rcu_read_{lock|unlock}() calls, as those still use RCU specific APIs
within them.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com> [Devfreq]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add kref to struct dev_pm_opp for easier accounting of the OPPs.
Note that the OPPs are freed under the opp_table->lock mutex only.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Migrate all users of _add_opp_table() to use dev_pm_opp_get_opp_table()
to guarantee that the OPP table doesn't get freed while being used.
Also update _managed_opp() to get the reference to the OPP table.
Now that the OPP table wouldn't get freed while these routines are
executing after dev_pm_opp_get_opp_table() is called, there is no need
to take opp_table_lock. Drop them as well.
Now that _add_opp_table(), _remove_opp_table() and the unlocked release
routines aren't used anymore, remove them.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Take reference of the OPP table while adding and removing OPPs, that
helps us remove special checks in _remove_opp_table().
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Now that we have proper kernel reference infrastructure in place for OPP
tables, use it to guarantee that the OPP table isn't freed while being
used by the callers of dev_pm_opp_set_*() APIs.
Make them all return the pointer to the OPP table after taking its
reference and put the reference back with dev_pm_opp_put_*() APIs.
Now that the OPP table wouldn't get freed while these routines are
executing after dev_pm_opp_get_opp_table() is called, there is no need
to take opp_table_lock. Drop them as well.
Remove the rcu specific comments from these routines as they aren't
relevant anymore.
Note that prototypes of dev_pm_opp_{set|put}_regulators() were already
updated by another patch.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add kref to struct opp_table for easier accounting of the OPP table.
Note that the new routine dev_pm_opp_get_opp_table() takes the reference
from under the opp_table_lock, which guarantees that the OPP table
doesn't get freed unless dev_pm_opp_put_opp_table() is called for the
OPP table.
Two separate release mechanisms are added: locked and unlocked. In
unlocked version the routines aren't required to take/drop
opp_table_lock as the callers have already done that. This is required
to avoid breaking git bisect, otherwise we may get lockdeps between
commits. Once all the users of OPP table are updated the unlocked
version shall be removed.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add per OPP table lock to protect opp_table->opp_list.
Note that at few places opp_list is used under the rcu_read_lock() and
so a mutex can't be added there for now. This will be fixed by a later
patch.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Split out parts of _add_opp_table() and _remove_opp_table() into
separate routines. This improves readability as well.
Should result in no functional changes.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Let the OPP core provide helpers to register notifiers for any device,
instead of exposing srcu_head outside of the core.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There is only one user of dev_pm_opp_get_suspend_opp() and that uses it
to get the OPP rate for the suspend_opp.
Rename dev_pm_opp_get_suspend_opp() as dev_pm_opp_get_suspend_opp_freq()
and return the rate directly from it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There is no point in trying to find/allocate the table for every OPP
that is added for a device. It would be far more efficient to allocate
the table only once and pass its pointer to the routines that add the
OPP entry.
Locking is removed from _opp_add_static_v2() and _opp_add_v1() now as
the callers call them with that lock already held.
Call to _remove_opp_table() routine is also removed from _opp_free()
now, as opp_table isn't allocated from within _opp_allocate(). This is
handled by the routines which created the OPP table in the first place.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Later patches would want to remove OPP table (and its OPPs) using the
opp_table pointer instead of 'dev'.
In order to prepare for that, rename _dev_pm_opp_remove_table() as
_dev_pm_opp_find_and_remove_table() split out part of it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The OPPs which are never successfully added using _opp_add() are not
required to be freed with the _opp_remove() routine, as a simple kfree()
is enough for them.
Introduce a new light weight routine _opp_free(), which will do that.
That also helps us removing the 'notify' parameter to _opp_remove(),
which isn't required anymore.
Note that _opp_free() contains a call to _remove_opp_table() as the OPP
table might have been added for this very OPP only. The
_remove_opp_table() routine returns quickly if there are more OPPs in
the table. This will be simplified in later patches though.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The code adding static OPPs for V2 bindings already does so. Make the V1
bindings specific code behave the same.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Make the naming consistent with how other routines are named.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This TODO doesn't make sense anymore as we have all the information in a
single OPP table. Remove it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There are two types of duplicate OPPs that get different behavior from
the core:
A) An earlier OPP is marked 'available' and has same freq/voltages as
the new one.
B) An earlier OPP with same frequency, but is marked 'unavailable' OR
doesn't have same voltages as the new one.
The OPP core returns 0 for the first one, but -EEXIST for the second.
While the OPP core returns 0 for the first case, its callers don't free
the newly allocated OPP structure which isn't used anymore. Fix that by
returning -EBUSY instead of 0, but make the callers return 0 eventually.
As this isn't a critical fix, its not getting marked for stable kernel.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently the mix of genpd_poweron(), genpd_power_on(),
genpd_sync_poweron() and the ->power_on() callback, makes
a bit difficult to follow the path of execution. The similar
applies to the functions dealing with power off.
In a way to improve this understanding, let's do the following renaming:
genpd_power_on() -> _genpd_power_on()
genpd_poweron() -> genpd_power_on()
genpd_sync_poweron() -> genpd_sync_power_on()
genpd_power_off() -> _genpd_power_off()
genpd_poweroff() -> genpd_power_off()
genpd_sync_poweroff() -> genpd_sync_power_off()
genpd_poweroff_unused() -> genpd_power_off_unused()
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch fixes the following gcc warning:
drivers/base/power/domain.c: In function ‘genpd_runtime_resume’:
drivers/base/power/domain.c:642:14: warning: ‘time_start’ may be used
uninitialized in this function [-Wmaybe-uninitialized]
elapsed_ns = ktime_to_ns(ktime_sub(ktime_get(), time_start)
The same problem (in another function in this same file) was fixed in
commit d33d5a6c88 (avoid spurious "may be used uninitialized" warning)
Signed-off-by: Augusto Mecking Caringi <augustocaringi@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The timer type simplifications caused a new gcc warning:
drivers/base/power/domain.c: In function ‘genpd_runtime_suspend’:
drivers/base/power/domain.c:562:14: warning: ‘time_start’ may be used uninitialized in this function [-Wmaybe-uninitialized]
elapsed_ns = ktime_to_ns(ktime_sub(ktime_get(), time_start));
despite the actual use of "time_start" not having changed in any way.
It appears that simply changing the type of ktime_t from a union to a
plain scalar type made gcc check the use.
The variable wasn't actually used uninitialized, but gcc apparently
failed to notice that the conditional around the use was exactly the
same as the conditional around the initialization of that variable.
Add an unnecessary initialization just to shut up the compiler.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ktime_set(S,N) was required for the timespec storage type and is still
useful for situations where a Seconds and Nanoseconds part of a time value
needs to be converted. For anything where the Seconds argument is 0, this
is pointless and can be replaced with a simple assignment.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
ktime is a union because the initial implementation stored the time in
scalar nanoseconds on 64 bit machine and in a endianess optimized timespec
variant for 32bit machines. The Y2038 cleanup removed the timespec variant
and switched everything to scalar nanoseconds. The union remained, but
become completely pointless.
Get rid of the union and just keep ktime_t as simple typedef of type s64.
The conversion was done with coccinelle and some manual mopping up.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Here's the new driver core patches for 4.10-rc1.
Big thing here is the nice addition of "functional dependencies" to the
driver core. The idea has been talked about for a very long time, great
job to Rafael for stepping up and implementing it. It's been tested for
longer than the 4.9-rc1 date, we held off on merging it earlier in order
to feel more comfortable about it.
Other than that, it's just a handful of small other patches, some good
cleanups to the mess that is the firmware class code, and we have a test
driver for the deferred probe logic.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWFAvPQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ym3NgCgmhFeWEkp9SDt17YGGavmnzQUlBQAoJlUipJp
PHeQkq15ZWw3wWC9FEvM
=91M1
-----END PGP SIGNATURE-----
Merge tag 'driver-core-4.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here's the new driver core patches for 4.10-rc1.
Big thing here is the nice addition of "functional dependencies" to
the driver core. The idea has been talked about for a very long time,
great job to Rafael for stepping up and implementing it. It's been
tested for longer than the 4.9-rc1 date, we held off on merging it
earlier in order to feel more comfortable about it.
Other than that, it's just a handful of small other patches, some good
cleanups to the mess that is the firmware class code, and we have a
test driver for the deferred probe logic.
All of these have been in linux-next for a while with no reported
issues"
* tag 'driver-core-4.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (30 commits)
firmware: Correct handling of fw_state_wait() return value
driver core: Silence device links sphinx warning
firmware: remove warning at documentation generation time
drivers: base: dma-mapping: Fix typo in dmam_alloc_non_coherent comments
driver core: test_async: fix up typo found by 0-day
firmware: move fw_state_is_done() into UHM section
firmware: do not use fw_lock for fw_state protection
firmware: drop bit ops in favor of simple state machine
firmware: refactor loading status
firmware: fix usermode helper fallback loading
driver core: firmware_class: convert to use class_groups
driver core: devcoredump: convert to use class_groups
driver core: class: add class_groups support
kernfs: Declare two local data structures static
driver-core: fix platform_no_drv_owner.cocci warnings
drivers/base/memory.c: Remove unused 'first_page' variable
driver core: add CLASS_ATTR_WO()
drivers: base: cacheinfo: support DT overrides for cache properties
drivers: base: cacheinfo: add pr_fmt logging
drivers: base: cacheinfo: fix boot error message when acpi is enabled
...
- New cpufreq driver for Broadcom STB SoCs and a Device Tree binding
for it (Markus Mayer).
- Support for ARM Integrator/AP and Integrator/CP in the generic
DT cpufreq driver and elimination of the old Integrator cpufreq
driver (Linus Walleij).
- Support for the zx296718, r8a7743 and r8a7745, Socionext UniPhier,
and PXA SoCs in the the generic DT cpufreq driver (Baoyou Xie,
Geert Uytterhoeven, Masahiro Yamada, Robert Jarzmik).
- cpufreq core fix to eliminate races that may lead to using
inactive policy objects and related cleanups (Rafael Wysocki).
- cpufreq schedutil governor update to make it use SCHED_FIFO
kernel threads (instead of regular workqueues) for doing delayed
work (to reduce the response latency in some cases) and related
cleanups (Viresh Kumar).
- New cpufreq sysfs attribute for resetting statistics (Markus
Mayer).
- cpufreq governors fixes and cleanups (Chen Yu, Stratos Karafotis,
Viresh Kumar).
- Support for using generic cpufreq governors in the intel_pstate
driver (Rafael Wysocki).
- Support for per-logical-CPU P-state limits and the EPP/EPB
(Energy Performance Preference/Energy Performance Bias) knobs
in the intel_pstate driver (Srinivas Pandruvada).
- New CPU ID for Knights Mill in intel_pstate (Piotr Luc).
- intel_pstate driver modification to use the P-state selection
algorithm based on CPU load on platforms with the system profile
in the ACPI tables set to "mobile" (Srinivas Pandruvada).
- intel_pstate driver cleanups (Arnd Bergmann, Rafael Wysocki,
Srinivas Pandruvada).
- cpufreq powernv driver updates including fast switching support
(for the schedutil governor), fixes and cleanus (Akshay Adiga,
Andrew Donnellan, Denis Kirjanov).
- acpi-cpufreq driver rework to switch it over to the new CPU
offline/online state machine (Sebastian Andrzej Siewior).
- Assorted cleanups in cpufreq drivers (Wei Yongjun, Prashanth
Prakash).
- Idle injection rework (to make it use the regular idle path
instead of a home-grown custom one) and related powerclamp
thermal driver updates (Peter Zijlstra, Jacob Pan, Petr Mladek,
Sebastian Andrzej Siewior).
- New CPU IDs for Atom Z34xx and Knights Mill in intel_idle (Andy
Shevchenko, Piotr Luc).
- intel_idle driver cleanups and switch over to using the new CPU
offline/online state machine (Anna-Maria Gleixner, Sebastian
Andrzej Siewior).
- cpuidle DT driver update to support suspend-to-idle properly
(Sudeep Holla).
- cpuidle core cleanups and misc updates (Daniel Lezcano, Pan Bian,
Rafael Wysocki).
- Preliminary support for power domains including CPUs in the
generic power domains (genpd) framework and related DT bindings
(Lina Iyer).
- Assorted fixes and cleanups in the generic power domains (genpd)
framework (Colin Ian King, Dan Carpenter, Geert Uytterhoeven).
- Preliminary support for devices with multiple voltage regulators
and related fixes and cleanups in the Operating Performance Points
(OPP) library (Viresh Kumar, Masahiro Yamada, Stephen Boyd).
- System sleep state selection interface rework to make it easier
to support suspend-to-idle as the default system suspend method
(Rafael Wysocki).
- PM core fixes and cleanups, mostly related to the interactions
between the system suspend and runtime PM frameworks (Ulf Hansson,
Sahitya Tummala, Tony Lindgren).
- Latency tolerance PM QoS framework imorovements (Andrew
Lutomirski).
- New Knights Mill CPU ID for the Intel RAPL power capping driver
(Piotr Luc).
- Intel RAPL power capping driver fixes, cleanups and switch over
to using the new CPU offline/online state machine (Jacob Pan,
Thomas Gleixner, Sebastian Andrzej Siewior).
- Fixes and cleanups in the exynos-ppmu, exynos-nocp, rk3399_dmc,
rockchip-dfi devfreq drivers and the devfreq core (Axel Lin,
Chanwoo Choi, Javier Martinez Canillas, MyungJoo Ham, Viresh
Kumar).
- Fix for false-positive KASAN warnings during resume from ACPI S3
(suspend-to-RAM) on x86 (Josh Poimboeuf).
- Memory map verification during resume from hibernation on x86 to
ensure a consistent address space layout (Chen Yu).
- Wakeup sources debugging enhancement (Xing Wei).
- rockchip-io AVS driver cleanup (Shawn Lin).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=vhxI
-----END PGP SIGNATURE-----
Merge tag 'pm-4.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"Again, cpufreq gets more changes than the other parts this time (one
new driver, one old driver less, a bunch of enhancements of the
existing code, new CPU IDs, fixes, cleanups)
There also are some changes in cpuidle (idle injection rework, a
couple of new CPU IDs, online/offline rework in intel_idle, fixes and
cleanups), in the generic power domains framework (mostly related to
supporting power domains containing CPUs), and in the Operating
Performance Points (OPP) library (mostly related to supporting devices
with multiple voltage regulators)
In addition to that, the system sleep state selection interface is
modified to make it easier for distributions with unchanged user space
to support suspend-to-idle as the default system suspend method, some
issues are fixed in the PM core, the latency tolerance PM QoS
framework is improved a bit, the Intel RAPL power capping driver is
cleaned up and there are some fixes and cleanups in the devfreq
subsystem
Specifics:
- New cpufreq driver for Broadcom STB SoCs and a Device Tree binding
for it (Markus Mayer)
- Support for ARM Integrator/AP and Integrator/CP in the generic DT
cpufreq driver and elimination of the old Integrator cpufreq driver
(Linus Walleij)
- Support for the zx296718, r8a7743 and r8a7745, Socionext UniPhier,
and PXA SoCs in the the generic DT cpufreq driver (Baoyou Xie,
Geert Uytterhoeven, Masahiro Yamada, Robert Jarzmik)
- cpufreq core fix to eliminate races that may lead to using inactive
policy objects and related cleanups (Rafael Wysocki)
- cpufreq schedutil governor update to make it use SCHED_FIFO kernel
threads (instead of regular workqueues) for doing delayed work (to
reduce the response latency in some cases) and related cleanups
(Viresh Kumar)
- New cpufreq sysfs attribute for resetting statistics (Markus Mayer)
- cpufreq governors fixes and cleanups (Chen Yu, Stratos Karafotis,
Viresh Kumar)
- Support for using generic cpufreq governors in the intel_pstate
driver (Rafael Wysocki)
- Support for per-logical-CPU P-state limits and the EPP/EPB (Energy
Performance Preference/Energy Performance Bias) knobs in the
intel_pstate driver (Srinivas Pandruvada)
- New CPU ID for Knights Mill in intel_pstate (Piotr Luc)
- intel_pstate driver modification to use the P-state selection
algorithm based on CPU load on platforms with the system profile in
the ACPI tables set to "mobile" (Srinivas Pandruvada)
- intel_pstate driver cleanups (Arnd Bergmann, Rafael Wysocki,
Srinivas Pandruvada)
- cpufreq powernv driver updates including fast switching support
(for the schedutil governor), fixes and cleanus (Akshay Adiga,
Andrew Donnellan, Denis Kirjanov)
- acpi-cpufreq driver rework to switch it over to the new CPU
offline/online state machine (Sebastian Andrzej Siewior)
- Assorted cleanups in cpufreq drivers (Wei Yongjun, Prashanth
Prakash)
- Idle injection rework (to make it use the regular idle path instead
of a home-grown custom one) and related powerclamp thermal driver
updates (Peter Zijlstra, Jacob Pan, Petr Mladek, Sebastian Andrzej
Siewior)
- New CPU IDs for Atom Z34xx and Knights Mill in intel_idle (Andy
Shevchenko, Piotr Luc)
- intel_idle driver cleanups and switch over to using the new CPU
offline/online state machine (Anna-Maria Gleixner, Sebastian
Andrzej Siewior)
- cpuidle DT driver update to support suspend-to-idle properly
(Sudeep Holla)
- cpuidle core cleanups and misc updates (Daniel Lezcano, Pan Bian,
Rafael Wysocki)
- Preliminary support for power domains including CPUs in the generic
power domains (genpd) framework and related DT bindings (Lina Iyer)
- Assorted fixes and cleanups in the generic power domains (genpd)
framework (Colin Ian King, Dan Carpenter, Geert Uytterhoeven)
- Preliminary support for devices with multiple voltage regulators
and related fixes and cleanups in the Operating Performance Points
(OPP) library (Viresh Kumar, Masahiro Yamada, Stephen Boyd)
- System sleep state selection interface rework to make it easier to
support suspend-to-idle as the default system suspend method
(Rafael Wysocki)
- PM core fixes and cleanups, mostly related to the interactions
between the system suspend and runtime PM frameworks (Ulf Hansson,
Sahitya Tummala, Tony Lindgren)
- Latency tolerance PM QoS framework imorovements (Andrew Lutomirski)
- New Knights Mill CPU ID for the Intel RAPL power capping driver
(Piotr Luc)
- Intel RAPL power capping driver fixes, cleanups and switch over to
using the new CPU offline/online state machine (Jacob Pan, Thomas
Gleixner, Sebastian Andrzej Siewior)
- Fixes and cleanups in the exynos-ppmu, exynos-nocp, rk3399_dmc,
rockchip-dfi devfreq drivers and the devfreq core (Axel Lin,
Chanwoo Choi, Javier Martinez Canillas, MyungJoo Ham, Viresh Kumar)
- Fix for false-positive KASAN warnings during resume from ACPI S3
(suspend-to-RAM) on x86 (Josh Poimboeuf)
- Memory map verification during resume from hibernation on x86 to
ensure a consistent address space layout (Chen Yu)
- Wakeup sources debugging enhancement (Xing Wei)
- rockchip-io AVS driver cleanup (Shawn Lin)"
* tag 'pm-4.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (127 commits)
devfreq: rk3399_dmc: Don't use OPP structures outside of RCU locks
devfreq: rk3399_dmc: Remove dangling rcu_read_unlock()
devfreq: exynos: Don't use OPP structures outside of RCU locks
Documentation: intel_pstate: Document HWP energy/performance hints
cpufreq: intel_pstate: Support for energy performance hints with HWP
cpufreq: intel_pstate: Add locking around HWP requests
PM / sleep: Print active wakeup sources when blocking on wakeup_count reads
PM / core: Fix bug in the error handling of async suspend
PM / wakeirq: Fix dedicated wakeirq for drivers not using autosuspend
PM / Domains: Fix compatible for domain idle state
PM / OPP: Don't WARN on multiple calls to dev_pm_opp_set_regulators()
PM / OPP: Allow platform specific custom set_opp() callbacks
PM / OPP: Separate out _generic_set_opp()
PM / OPP: Add infrastructure to manage multiple regulators
PM / OPP: Pass struct dev_pm_opp_supply to _set_opp_voltage()
PM / OPP: Manage supply's voltage/current in a separate structure
PM / OPP: Don't use OPP structure outside of rcu protected section
PM / OPP: Reword binding supporting multiple regulators per device
PM / OPP: Fix incorrect cpu-supply property in binding
cpuidle: Add a kerneldoc comment to cpuidle_use_deepest_state()
..
Pull timer updates from Thomas Gleixner:
"The time/timekeeping/timer folks deliver with this update:
- Fix a reintroduced signed/unsigned issue and cleanup the whole
signed/unsigned mess in the timekeeping core so this wont happen
accidentaly again.
- Add a new trace clock based on boot time
- Prevent injection of random sleep times when PM tracing abuses the
RTC for storage
- Make posix timers configurable for real tiny systems
- Add tracepoints for the alarm timer subsystem so timer based
suspend wakeups can be instrumented
- The usual pile of fixes and updates to core and drivers"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (23 commits)
timekeeping: Use mul_u64_u32_shr() instead of open coding it
timekeeping: Get rid of pointless typecasts
timekeeping: Make the conversion call chain consistently unsigned
timekeeping_Force_unsigned_clocksource_to_nanoseconds_conversion
alarmtimer: Add tracepoints for alarm timers
trace: Update documentation for mono, mono_raw and boot clock
trace: Add an option for boot clock as trace clock
timekeeping: Add a fast and NMI safe boot clock
timekeeping/clocksource_cyc2ns: Document intended range limitation
timekeeping: Ignore the bogus sleep time if pm_trace is enabled
selftests/timers: Fix spelling mistake "Asyncrhonous" -> "Asynchronous"
clocksource/drivers/bcm2835_timer: Unmap region obtained by of_iomap
clocksource/drivers/arm_arch_timer: Map frame with of_io_request_and_map()
arm64: dts: rockchip: Arch counter doesn't tick in system suspend
clocksource/drivers/arm_arch_timer: Don't assume clock runs in suspend
posix-timers: Make them configurable
posix_cpu_timers: Move the add_device_randomness() call to a proper place
timer: Move sys_alarm from timer.c to itimer.c
ptp_clock: Allow for it to be optional
Kconfig: Regenerate *.c_shipped files after previous changes
...
* pm-core:
PM / core: Fix bug in the error handling of async suspend
PM / wakeirq: Fix dedicated wakeirq for drivers not using autosuspend
PM / Runtime: Defer resuming of the device in pm_runtime_force_resume()
PM / Runtime: Don't allow to suspend a device with an active child
net: smsc911x: Synchronize the runtime PM status during system suspend
PM / Runtime: Convert pm_runtime_set_suspended() to return an int
PM / Runtime: Clarify comment in rpm_resume() when resuming the parent
PM / Runtime: Remove the exported function pm_children_suspended()
* pm-qos:
PM / QoS: Export dev_pm_qos_update_user_latency_tolerance
PM / QoS: Fix writing 'auto' to pm_qos_latency_tolerance_us
PM / QoS: Improve sysfs pm_qos_latency_tolerance validation
* pm-avs:
PM / AVS: rockchip-io: make the log more consistent
* pm-domains:
PM / Domains: Fix compatible for domain idle state
PM / Domains: Do not print PM domain add error message if EPROBE_DEFER
PM / Domains: Fix a warning message
PM / Domains: check for negative return from of_count_phandle_with_args()
PM / doc: Update device documentation for devices in IRQ-safe PM domains
PM / Domains: Support IRQ safe PM domains
PM / Domains: Abstract genpd locking
dt/bindings / PM/Domains: Update binding for PM domain idle states
PM / Domains: Save the fwnode in genpd_power_state
PM / Domains: Allow domain power states to be read from DT
PM / Domains: Add residency property to genpd states
PM / Domains: Make genpd state allocation dynamic
Conflicts:
arch/arm/mach-imx/gpc.c
If there are any wakeup events being processed, read operation
on /sys/power/wakeup_count will be blocked, so print the names
of all active wakeup sources to help to find out who is preventing
system suspend from triggering.
While at it change pr_info() in pm_print_active_wakeup_sources()
to pr_debug() to avoid excessive log noise.
Signed-off-by: xing wei <xing.wei@intel.com>
[ rjw: Subject & changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
If async_suspend is enabled for parent and child devices, then
PM framework has to ensure that parent's async suspend gets called
only after child's async suspend is done. In case if child's async
suspend fails with error, then parent's async suspend must not be
invoked. The current code uses async_error to ensure this but there
is a problem with it in __device_suspend(). This function notifies
the completion of child's async suspend before updating its error
via async_error variable. As a result, parent's async suspend gets
invoked even though it's child suspend has failed. Fix this bug by
updating the async_error before notifying the child's completion.
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
[ rjw: Rearranged wthitespace ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
I noticed some wakeirq flakeyness with consumer drivers not using
autosuspend. For drivers not using autosuspend, the wakeirq may never
get unmasked in rpm_suspend() because of irq desc->depth.
We are configuring dedicated wakeirqs to start with IRQ_NOAUTOEN as we
naturally don't want them running until rpm_suspend() is called.
However, when a consumer driver initially calls pm_runtime_get(), we
now wrongly start with disable_irq_nosync() call on the dedicated
wakeirq that is disabled to start with.
This causes desc->depth to toggle between 1 and 2 instead of the usual
0 and 1. This can prevent enable_irq() from unmasking the wakeirq as
that only happens at desc->depth 1.
This does not necessarily show up with drivers using autosuspend as
there is time for disable_irq_nosync() before rpm_suspend() gets called
after the autosuspend timeout.
Let's fix the issue by adding wirq->status that lazily gets set on
the first rpm_suspend(). We also need PM runtime core private functions
for dev_pm_enable_wake_irq_check() and dev_pm_disable_wake_irq_check()
so we can enable the dedicated wakeirq on the first rpm_suspend().
While at it, let's also fix the comments for dev_pm_enable_wake_irq()
and dev_pm_disable_wake_irq(). Those can still be used by the consumer
drivers as needed because the IRQ core manages the interrupt usecount
for us.
Fixes: 4990d4fe32 (PM / Wakeirq: Add automated device wake IRQ handling)
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Re-using idle state definition provided by arm,idle-state for domain
idle states creates a lot of confusion and limits further evolution of
the domain idle definition. To keep things clear and simple, define a
idle states for domain using a new compatible "domain-idle-state".
Fix existing PM domains code to look for the newly defined compatible.
Signed-off-by: Lina Iyer <lina.iyer@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
If a platform specific OPP driver has called this routine first and set
the regulators, then the second call from cpufreq-dt driver will hit the
WARN_ON(). Remove the WARN_ON(), but continue to return error in such
cases.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Tested-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The generic set_opp() handler isn't sufficient for platforms with
complex DVFS. For example, some TI platforms have multiple regulators
for a CPU device. The order in which various supplies need to be
programmed is only known to the platform code and its best to leave it
to it.
This patch implements APIs to register platform specific set_opp()
callback.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Dave Gerlach <d-gerlach@ti.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Later patches would add support for custom set_opp() callbacks. This
patch separates out the code for _generic_set_opp() handler in order to
prepare for that.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Dave Gerlach <d-gerlach@ti.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch adds infrastructure to manage multiple regulators and updates
the only user (cpufreq-dt) of dev_pm_opp_set{put}_regulator().
This is preparatory work for adding full support for devices with
multiple regulators.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pass the entire supply structure instead of all of its fields.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Dave Gerlach <d-gerlach@ti.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This is a preparatory step for multiple regulator per device support.
Move the voltage/current variables to a new structure.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Dave Gerlach <d-gerlach@ti.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The OPP structure must not be used out of the rcu protected section.
Cache the values to be used in separate variables instead.
Cc: 4.6+ <stable@vger.kernel.org> # 4.6+
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Tested-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Joonyoung Shim reported an interesting problem on his ARM octa-core
Odoroid-XU3 platform. During system suspend, dev_pm_opp_put_regulator()
was failing for a struct device for which dev_pm_opp_set_regulator() is
called earlier.
This happened because an earlier call to
dev_pm_opp_of_cpumask_remove_table() function (from cpufreq-dt.c file)
removed all the entries from opp_table->dev_list apart from the last CPU
device in the cpumask of CPUs sharing the OPP.
But both dev_pm_opp_set_regulator() and dev_pm_opp_put_regulator()
routines get CPU device for the first CPU in the cpumask. And so the OPP
core failed to find the OPP table for the struct device.
This patch attempts to fix this problem by returning a pointer to the
opp_table from dev_pm_opp_set_regulator() and using that as the
parameter to dev_pm_opp_put_regulator(). This ensures that the
dev_pm_opp_put_regulator() doesn't fail to find the opp table.
Note that similar design problem also exists with other
dev_pm_opp_put_*() APIs, but those aren't used currently by anyone and
so we don't need to update them for now.
Cc: 4.4+ <stable@vger.kernel.org> # 4.4+
Reported-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
[ Viresh: Wrote commit log and tested on exynos 5250 ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
EPROBE_DEFER is not an error, hence printing an error message like
renesas_irqc e61c0000.interrupt-controller: failed to add to PM domain always-on: -517
may confuse the user.
Suppress the error message in case of EPROBE_DEFER to fix this.
Reported-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
nvme wants a module parameter that overrides the default latency
tolerance. This makes it easy for nvme to reflect that default in
sysfs.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
If it was already 'auto', then writing 'auto' again would
incorrectly fail.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Negative values are special. Don't let users write them directly.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Power management suspend/resume tracing (ab)uses the RTC to store
suspend/resume information persistently. As a consequence the RTC value is
clobbered when timekeeping is resumed and tries to inject the sleep time.
Commit a4f8f6667f ("timekeeping: Cap array access in timekeeping_debug")
plugged a out of bounds array access in the timekeeping debug code which
was caused by the clobbered RTC value, but we still use the clobbered RTC
value for sleep time injection into kernel timekeeping, which will result
in random adjustments depending on the stored "hash" value.
To prevent this keep track of the RTC clobbering and ignore the invalid RTC
timestamp at resume. If the system resumed successfully clear the flag,
which marks the RTC as unusable, warn the user about the RTC clobber and
recommend to adjust the RTC with 'ntpdate' or 'rdate'.
[jstultz: Fixed up pr_warn formating, and implemented suggestions from Ingo]
[ tglx: Rewrote changelog ]
Originally-from: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Xunlei Pang <xlpang@redhat.com>
Cc: Len Brown <lenb@kernel.org>
Link: http://lkml.kernel.org/r/1480372524-15181-3-git-send-email-john.stultz@linaro.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
When the pm_runtime_force_suspend|resume() helpers were invented, we still
had CONFIG_PM_RUNTIME and CONFIG_PM_SLEEP as separate Kconfig options.
To make sure these helpers worked for all combinations and without
introducing too much of complexity, the device was always resumed in
pm_runtime_force_resume().
More precisely, when CONFIG_PM_SLEEP was set and CONFIG_PM_RUNTIME was
unset, we needed to resume the device as the subsystem/driver couldn't
rely on using runtime PM to do it.
As the CONFIG_PM_RUNTIME option was merged into CONFIG_PM a while ago, it
removed this combination, of using CONFIG_PM_SLEEP without the earlier
CONFIG_PM_RUNTIME.
For this reason we can now rely on the subsystem/driver to use runtime PM
to resume the device, instead of forcing that to be done in all cases. In
other words, let's defer the runtime resume to a later point when it's
actually needed.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The first argument of WARN() is the condition, followed by the message.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Consider two devices, A and B, where B is a child of A, and B utilizes
asynchronous suspend (it does not matter whether A is sync or async). If
B fails to suspend_noirq() or suspend_late(), or is interrupted by a
wakeup (pm_wakeup_pending()), then it aborts and sets the async_error
variable. However, device A does not (immediately) check the async_error
variable; it may continue to run its own suspend_noirq()/suspend_late()
callback. This is bad.
We can resolve this problem by doing our error and wakeup checking
(particularly, for the async_error flag) after waiting for children to
suspend, instead of before. This also helps align the logic for the noirq and
late suspend cases with the logic in __device_suspend().
It's easy to observe this erroneous behavior by, for example, forcing a
device to sleep a bit in its suspend_noirq() (to ensure the parent is
waiting for the child to complete), then return an error, and watch the
parent suspend_noirq() still get called. (Or similarly, fake a wakeup
event at the right (or is it wrong?) time.)
Fixes: de377b3972 (PM / sleep: Asynchronous threads for suspend_late)
Fixes: 28b6fd6e37 (PM / sleep: Asynchronous threads for suspend_noirq)
Reported-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When resuming a device in __pm_runtime_set_status(), the prerequisite is
that its parent must already be active, else an error code is returned and
the device's status remains suspended.
When suspending a device there is no similar constraints being validated.
Let's change this to make the behaviour consistent, by not allowing to
suspend a device with an active child, unless it has been explicitly set to
ignore its children.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
If the device has no links to suppliers that should be used for
runtime PM (links with DEVICE_LINK_PM_RUNTIME set), there is no
reason to walk the list of suppliers for that device during
runtime suspend and resume.
Add a simple mechanism to detect that case and possibly avoid the
extra unnecessary overhead.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Modify the runtime PM framework to use device links to ensure that
supplier devices will not be suspended if any of their consumer
devices are active.
The idea is to reference count suppliers on the consumer's resume
and drop references to them on its suspend. The information on
whether or not the supplier has been reference counted by the
consumer's (runtime) resume is stored in a new field (rpm_active)
in the link object for each link.
It may be necessary to clean up those references when the
supplier is unbinding and that's why the links whose status is
DEVICE_LINK_SUPPLIER_UNBIND are skipped by the runtime suspend
and resume code.
The above means that if the consumer device is probed in the
runtime-active state, the supplier has to be resumed and reference
counted by device_link_add() so the code works as expected on its
(runtime) suspend. There is a new flag, DEVICE_LINK_RPM_ACTIVE,
to tell device_link_add() about that (in which case the caller
is responsible for making sure that the consumer really will
be runtime-active when runtime PM is enabled for it).
The other new link flag, DEVICE_LINK_PM_RUNTIME, tells the core
whether or not the link should be used for runtime PM at all.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make the device suspend/resume part of the core system
suspend/resume code use device links to ensure that supplier
and consumer devices will be suspended and resumed in the right
order in case of async suspend/resume.
The idea, roughly, is to use dpm_wait() to wait for all consumers
before a supplier device suspend and to wait for all suppliers
before a consumer device resume.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, there is a problem with taking functional dependencies
between devices into account.
What I mean by a "functional dependency" is when the driver of device
B needs device A to be functional and (generally) its driver to be
present in order to work properly. This has certain consequences
for power management (suspend/resume and runtime PM ordering) and
shutdown ordering of these devices. In general, it also implies that
the driver of A needs to be working for B to be probed successfully
and it cannot be unbound from the device before the B's driver.
Support for representing those functional dependencies between
devices is added here to allow the driver core to track them and act
on them in certain cases where applicable.
The argument for doing that in the driver core is that there are
quite a few distinct use cases involving device dependencies, they
are relatively hard to get right in a driver (if one wants to
address all of them properly) and it only gets worse if multiplied
by the number of drivers potentially needing to do it. Morever, at
least one case (asynchronous system suspend/resume) cannot be handled
in a single driver at all, because it requires the driver of A to
wait for B to suspend (during system suspend) and the driver of B to
wait for A to resume (during system resume).
For this reason, represent dependencies between devices as "links",
with the help of struct device_link objects each containing pointers
to the "linked" devices, a list node for each of them, status
information, flags, and an RCU head for synchronization.
Also add two new list heads, representing the lists of links to the
devices that depend on the given one (consumers) and to the devices
depended on by it (suppliers), and a "driver presence status" field
(needed for figuring out initial states of device links) to struct
device.
The entire data structure consisting of all of the lists of link
objects for all devices is protected by a mutex (for link object
addition/removal and for list walks during device driver probing
and removal) and by SRCU (for list walking in other case that will
be introduced by subsequent change sets). If CONFIG_SRCU is not
selected, however, an rwsem is used for protecting the entire data
structure.
In addition, each link object has an internal status field whose
value reflects whether or not drivers are bound to the devices
pointed to by the link or probing/removal of their drivers is in
progress etc. That field is only modified under the device links
mutex, but it may be read outside of it in some cases (introduced by
subsequent change sets), so modifications of it are annotated with
WRITE_ONCE().
New links are added by calling device_link_add() which takes three
arguments: pointers to the devices in question and flags. In
particular, if DL_FLAG_STATELESS is set in the flags, the link status
is not to be taken into account for this link and the driver core
will not manage it. In turn, if DL_FLAG_AUTOREMOVE is set in the
flags, the driver core will remove the link automatically when the
consumer device driver unbinds from it.
One of the actions carried out by device_link_add() is to reorder
the lists used for device shutdown and system suspend/resume to
put the consumer device along with all of its children and all of
its consumers (and so on, recursively) to the ends of those lists
in order to ensure the right ordering between all of the supplier
and consumer devices.
For this reason, it is not possible to create a link between two
devices if the would-be supplier device already depends on the
would-be consumer device as either a direct descendant of it or a
consumer of one of its direct descendants or one of its consumers
and so on.
There are two types of link objects, persistent and non-persistent.
The persistent ones stay around until one of the target devices is
deleted, while the non-persistent ones are removed automatically when
the consumer driver unbinds from its device (ie. they are assumed to
be valid only as long as the consumer device has a driver bound to
it). Persistent links are created by default and non-persistent
links are created when the DL_FLAG_AUTOREMOVE flag is passed
to device_link_add().
Both persistent and non-persistent device links can be deleted
with an explicit call to device_link_del().
Links created without the DL_FLAG_STATELESS flag set are managed
by the driver core using a simple state machine. There are 5 states
each link can be in: DORMANT (unused), AVAILABLE (the supplier driver
is present and functional), CONSUMER_PROBE (the consumer driver is
probing), ACTIVE (both supplier and consumer drivers are present and
functional), and SUPPLIER_UNBIND (the supplier driver is unbinding).
The driver core updates the link state automatically depending on
what happens to the linked devices and for each link state specific
actions are taken in addition to that.
For example, if the supplier driver unbinds from its device, the
driver core will also unbind the drivers of all of its consumers
automatically under the assumption that they cannot function
properly without the supplier. Analogously, the driver core will
only allow the consumer driver to bind to its device if the
supplier driver is present and functional (ie. the link is in
the AVAILABLE state). If that's not the case, it will rely on
the existing deferred probing mechanism to wait for the supplier
driver to become available.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The return from of_count_phandle_with_args can be negative, so we
should avoid kcalloc of a negative count of genpd_power_stat structs
by sanity checking if count is zero or less.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Generic Power Domains currently support turning on/off only in process
context. This prevents the usage of PM domains for domains that could be
powered on/off in a context where IRQs are disabled. Many such domains
exist today and do not get powered off, when the IRQ safe devices in
that domain are powered off, because of this limitation.
However, not all domains can operate in IRQ safe contexts. Genpd
therefore, has to support both cases where the domain may or may not
operate in IRQ safe contexts. Configuring genpd to use an appropriate
lock for that domain, would allow domains that have IRQ safe devices to
runtime suspend and resume, in atomic context.
To achieve domain specific locking, set the domain's ->flag to
GENPD_FLAG_IRQ_SAFE while defining the domain. This indicates that genpd
should use a spinlock instead of a mutex for locking the domain. Locking
is abstracted through genpd_lock() and genpd_unlock() functions that use
the flag to determine the appropriate lock to be used for that domain.
Domains that have lower latency to suspend and resume and can operate
with IRQs disabled may now be able to save power, when the component
devices and sub-domains are idle at runtime.
The restriction this imposes on the domain hierarchy is that non-IRQ
safe domains may not have IRQ-safe subdomains, but IRQ safe domains may
have IRQ safe and non-IRQ safe subdomains and devices.
Signed-off-by: Lina Iyer <lina.iyer@linaro.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Abstract genpd lock/unlock calls, in preparation for domain specific
locks added in the following patches.
Signed-off-by: Lina Iyer <lina.iyer@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Save the fwnode for the genpd state in the state node. PM Domain clients
may use the fwnode to read in the platform specific domain state
properties and associate them with the state.
Signed-off-by: Lina Iyer <lina.iyer@linaro.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch allows domains to define idle states in the DT. SoC's can
define domain idle states in DT using the "domain-idle-states" property
of the domain provider. Add API to read the idle states from DT that can
be set in the genpd object.
This patch is based on the original patch by Marc Titinger.
Signed-off-by: Marc Titinger <mtitinger+renesas@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Lina Iyer <lina.iyer@linaro.org>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Allow PM Domain states to be defined dynamically by the drivers. This
removes the limitation on the maximum number of states possible for a
domain.
Suggested-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Lina Iyer <lina.iyer@linaro.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The exported function pm_children_suspended() has only one caller, which is
the runtime PM internal function, rpm_check_suspend_allowed().
Let's clean-up this code, by removing pm_children_suspended() altogether
and instead do the one-liner check directly in rpm_check_suspend_allowed().
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
These log messages are wrong because _of_get_opp_desc_node() returns
an operating-points-v2 node.
Commit a6eed752f5 ("PM / OPP: passing NULL to PTR_ERR()") fixed
static checker warnings, and reworded the messages at the same time
(but the latter was not mentioned in the git-log).
Restore the correct messages.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Since commit f47b72a15a ("PM / OPP: Move CONFIG_OF dependent code
in a separate file"), this function is defined and called only in
drivers/base/power/opp/of.c .
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* pm-domains:
PM / Domains: Rename pm_genpd_sync_poweron|poweroff()
PM / Domains: Don't measure latency of ->power_on|off() during system PM
PM / Domains: Remove redundant system PM callbacks
PM / Domains: Simplify detaching a device from its genpd
PM / Domains: Allow holes in genpd_data.domains array
PM / Domains: Add support for removing nested PM domains by provider
PM / Domains: Add support for removing PM domains
PM / Domains: Store the provider in the PM domain structure
PM / Domains: Prepare for adding support to remove PM domains
PM / Domains: Verify the PM domain is present when adding a provider
PM / Domains: Don't expose xlate and provider helper functions
PM / Domains: Don't expose generic_pm_domain structure to clients
staging: board: Remove calls to of_genpd_get_from_provider()
ARM: EXYNOS: Remove calls to of_genpd_get_from_provider()
PM / Domains: Add new helper functions for device-tree
PM / Domains: Always enable debugfs support if available
The OPP framework allows each OPP to set a opp-supported-hw property
which provides values that are matched against supported_hw values
provided by the platform to limit support for certain OPPs on specific
hardware. Currently, if the platform does not set supported_hw values,
all OPPs are interpreted as supported, even if they have provided their
own opp-supported-hw values.
If an OPP has provided opp-supported-hw, it is indicating that there is
some specific hardware configuration it is supported by. These constraints
should be honored, and if no supported_hw has been provided by the
platform, there is no way to determine if that OPP is actually supported,
so it should be marked as not supported.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
These are internal static functions to genpd. Let's conform to the naming
rules, by dropping the "pm_" prefix from these.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Measure latency does by itself contribute to an increased latency, thus we
should avoid it when it isn't needed.
Currently genpd measures latencies in the system PM phase for the
->power_on|off() callbacks, except in the syscore case when it's not
allowed to use ktime_get() as timekeeping may be suspended.
Since there should be plenty of occasions during runtime PM to perform
these measurements, let's rely on that and drop them from system PM. This
will also make it consistent for how measurements are done of the runtime
PM callbacks (as those may be invoked during system PM).
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In cases when the PM domain haven't assigned a system PM callback, the PM
core fall-backs to check for the callback at the driver level instead.
This makes it redundant to assign a pm_generic_* helper function to a
corresponding system PM callback at a PM domain level.
Therefore, let's remove these assignments in pm_genpd_init().
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There's no need to validate the PM domain by using genpd_lookup_dev() when
removing the device via genpd's genpd_dev_pm_detach() function. That's
because this function can't be called, unless there is a valid PM domain
for the device.
To simplify the behaviour, let's move code from pm_genpd_remove_device()
into a new internal function, genpd_remove_device(), which is called from
pm_genpd_remove_device() and genpd_dev_pm_detach().
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Lina Iyer <lina.iyer@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When CONFIG_OPTIMIZE_INLINING is set and we are building with -Wmaybe-uninitialized
enabled, we can get a warning for the opp core driver:
drivers/base/power/opp/core.c: In function 'dev_pm_opp_set_rate':
drivers/base/power/opp/core.c:560:8: warning: 'ou_volt_min' may be used uninitialized in this function [-Wmaybe-uninitialized]
This has only now appeared as a result of commit 797da5598f ("PM / devfreq:
Add COMPILE_TEST for build coverage"), which makes the driver visible in
some configurations that didn't have it before.
The warning is a false positive that I got with gcc-6.1.1, but there is
a simple workaround in removing the local variables that we get warnings
for (all three are affected depending on the configuration). This also
makes the code easier to read.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In platforms such as Rockchip's, the array of domains isn't always
filled without holes, as which domains are present depend on the
particular SoC revision.
By allowing holes to be in the array, such SoCs can still use a single
set of constants to index the array of power domains.
Fixes: 0159ec6707 (PM / Domains: Verify the PM domain is present when adding a provider)
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Further testing with false negatives suppressed by commit 293e2421fe
("rcu: Remove superfluous versions of rcu_read_lock_sched_held()")
identified a few more unprotected uses of RCU from the idle loop.
Because RCU actively ignores idle-loop code (for energy-efficiency
reasons, among other things), using RCU from the idle loop can result
in too-short grace periods, in turn resulting in arbitrary misbehavior.
The affected function is rpm_suspend().
The resulting lockdep-RCU splat is as follows:
------------------------------------------------------------------------
Warning from omap3
===============================
[ INFO: suspicious RCU usage. ]
4.6.0-rc5-next-20160426+ #1112 Not tainted
-------------------------------
include/trace/events/rpm.h:63 suspicious rcu_dereference_check() usage!
other info that might help us debug this:
RCU used illegally from idle CPU!
rcu_scheduler_active = 1, debug_locks = 0
RCU used illegally from extended quiescent state!
1 lock held by swapper/0/0:
#0: (&(&dev->power.lock)->rlock){-.-...}, at: [<c052ee24>] __pm_runtime_suspend+0x54/0x84
stack backtrace:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.6.0-rc5-next-20160426+ #1112
Hardware name: Generic OMAP36xx (Flattened Device Tree)
[<c0110308>] (unwind_backtrace) from [<c010c3a8>] (show_stack+0x10/0x14)
[<c010c3a8>] (show_stack) from [<c047fec8>] (dump_stack+0xb0/0xe4)
[<c047fec8>] (dump_stack) from [<c052d7b4>] (rpm_suspend+0x604/0x7e4)
[<c052d7b4>] (rpm_suspend) from [<c052ee34>] (__pm_runtime_suspend+0x64/0x84)
[<c052ee34>] (__pm_runtime_suspend) from [<c04bf3bc>] (omap2_gpio_prepare_for_idle+0x5c/0x70)
[<c04bf3bc>] (omap2_gpio_prepare_for_idle) from [<c01255e8>] (omap_sram_idle+0x140/0x244)
[<c01255e8>] (omap_sram_idle) from [<c0126b48>] (omap3_enter_idle_bm+0xfc/0x1ec)
[<c0126b48>] (omap3_enter_idle_bm) from [<c0601db8>] (cpuidle_enter_state+0x80/0x3d4)
[<c0601db8>] (cpuidle_enter_state) from [<c0183c74>] (cpu_startup_entry+0x198/0x3a0)
[<c0183c74>] (cpu_startup_entry) from [<c0b00c0c>] (start_kernel+0x354/0x3c8)
[<c0b00c0c>] (start_kernel) from [<8000807c>] (0x8000807c)
------------------------------------------------------------------------
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
[ rjw: Subject ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
If a device supports PM domains that are subdomains of another PM
domain, then the PM domains should be removed in reverse order to
ensure that the subdomains are removed first. Furthermore, if there is
more than one provider, then there needs to be a way to remove the
domains in reverse order for a specific provider.
Add the function of_genpd_remove_last() to remove the last PM domain
added by a given PM domain provider and return the generic_pm_domain
structure for the PM domain that was removed.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The genpd framework allows users to add PM domains via the pm_genpd_init()
function, however, there is no corresponding function to remove a PM
domain. For most devices this may be fine as the PM domains are never
removed, however, for devices that wish to populate the PM domains from
within a driver, having the ability to remove a PM domain if the probing
of the device fails or the driver is unloaded is necessary.
Add the function pm_genpd_remove() to remove a PM domain by referencing
it's generic_pm_domain structure. Note that the bulk of the code that
removes the PM domain is placed in a separate local function
genpd_remove() (which is called by pm_genpd_remove()). The code is
structured in this way to prepare for adding another function to remove
a PM domain by provider that will also call genpd_remove(). Note that
users of genpd_remove() must call this function with the mutex,
gpd_list_lock, held.
PM domains can only be removed if the associated provider has been
removed, they are not a parent domain to another PM domain and have no
devices associated with them.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
It is possible that a device has more than one provider of PM domains
and to support the removal of a PM domain by provider, it is necessary
to store a reference to the provider in the PM domain structure.
Therefore, store a reference to the firmware node handle in the PM
domain structure and populate it when providers (only device-tree based
providers are currently supported by PM domains) are registered.
Please note that when removing PM domains, it is necessary to verify
that the PM domain provider has been removed from the list of providers
before the PM domain can be removed. To do this add another member to
the PM domain structure that indicates if the provider is present and
set this member accordingly when providers are added and removed.
Initialise the 'provider' and 'has_provider' members of the
generic_pm_domain structure when a PM domains is added by calling
pm_genpd_init().
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In order to remove PM domains safely from the list of PM domains,
it is necessary to adding locking for the PM domain list around any
places where devices or subdomains are added to a PM domain.
There are places where a reference to a PM domain is obtained via
calling of_genpd_get_from_provider() before adding the device or the
subdomain. In these cases a lock for the PM domain list needs to be
held around the call to of_genpd_get_from_provider() and the call to
add the device/subdomain. To avoid deadlocks by multiple attempts to
obtain the PM domain list lock, add functions genpd_add_device() and
genpd_add_subdomain() which require the user to hold the PM domain
list lock when calling.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When a PM domain provider is added, there is currently no way to tell if
any PM domains associated with the provider are present. Naturally, the
PM domain provider should not be registered if the PM domains have not
been added. Nonetheless, verify that the PM domain(s) associated with a
provider are present when registering the PM domain provider.
This change adds a dependency on the function pm_genpd_present() when
CONFIG_PM_GENERIC_DOMAINS_OF is enabled and so ensure this function is
available when CONFIG_PM_GENERIC_DOMAINS_OF selected.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Functions __of_genpd_xlate_simple(), __of_genpd_xlate_onecell() and
__of_genpd_add_provider() are not used outside of the core generic PM
domain code. Therefore, reduce the number of APIs exposed by making
these static. At the same time don't expose the typedef for
genpd_xlate_t either and make this a local definition as well.
The functions are renamed to follow the naming conventions for static
functions in the generic PM domain core.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There should be no need to expose the generic_pm_domain structure to
clients and this eliminates the need to implement reference counting for
any external reference to a PM domain. Therefore, make the functions
pm_genpd_lookup_dev() and of_genpd_get_from_provider() private to the
PM domain core. The functions are renamed in accordance with the naming
conventions for genpd static functions.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Ideally, if we are returning a reference to a PM domain via a call to
of_genpd_get_from_provider(), then we should keep track of such
references via a reference count. The reference count could then be used
to determine if a PM domain can be safely removed. Alternatively, it is
possible to avoid such external references by providing APIs to access
the PM domain and hence, eliminate any calls to
of_genpd_get_from_provider().
Add new helper functions for adding a device and a subdomain to a PM
domain when using device-tree, so that external calls to
of_genpd_get_from_provider() can be removed.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This commit appends a few _rcuidle suffixes to fix the following
RCU-used-from-idle bug:
> ===============================
> [ INFO: suspicious RCU usage. ]
> 4.6.0-rc5-next-20160426+ #1116 Not tainted
> -------------------------------
> include/trace/events/rpm.h:95 suspicious rcu_dereference_check() usage!
>
> other info that might help us debug this:
>
>
> RCU used illegally from idle CPU!
> rcu_scheduler_active = 1, debug_locks = 0
> RCU used illegally from extended quiescent state!
> 1 lock held by swapper/0/0:
> #0: (&(&dev->power.lock)->rlock){-.-...}, at: [<c052cc2c>] __rpm_callback+0x58/0x60
>
> stack backtrace:
> CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.6.0-rc5-next-20160426+ #1116
> Hardware name: Generic OMAP36xx (Flattened Device Tree)
> [<c0110290>] (unwind_backtrace) from [<c010c3a8>] (show_stack+0x10/0x14)
> [<c010c3a8>] (show_stack) from [<c047fd68>] (dump_stack+0xb0/0xe4)
> [<c047fd68>] (dump_stack) from [<c052d5d0>] (rpm_suspend+0x580/0x768)
> [<c052d5d0>] (rpm_suspend) from [<c052ec58>] (__pm_runtime_suspend+0x64/0x84)
> [<c052ec58>] (__pm_runtime_suspend) from [<c04bf25c>] (omap2_gpio_prepare_for_idle+0x5c/0x70)
> [<c04bf25c>] (omap2_gpio_prepare_for_idle) from [<c0125568>] (omap_sram_idle+0x140/0x244)
> [<c0125568>] (omap_sram_idle) from [<c01269dc>] (omap3_enter_idle_bm+0xfc/0x1ec)
> [<c01269dc>] (omap3_enter_idle_bm) from [<c0601bdc>] (cpuidle_enter_state+0x80/0x3d4)
> [<c0601bdc>] (cpuidle_enter_state) from [<c0183b08>] (cpu_startup_entry+0x198/0x3a0)
> [<c0183b08>] (cpu_startup_entry) from [<c0b00c0c>] (start_kernel+0x354/0x3c8)
> [<c0b00c0c>] (start_kernel) from [<8000807c>] (0x8000807c)
In the immortal words of Steven Rostedt, "*Whack* *Whack* *Whack*!!!"
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
WhACKED-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Debugfs support for PM domains is only enabled if both CONFIG_PM_DEBUG
and CONFIG_PM_ADVANCED_DEBUG are enabled. CONFIG_PM_ADVANCED_DEBUG is
described as "extra PM attributes in sysfs for low-level
debugging/testing" which does not seem related.
Given that the debugfs for PM domains only allows users to view the
state of the PM domains, always enable debugfs support for PM domains
if PM domains and debugfs support is enabled.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- Prevent the low-level assembly hibernate code on x86-64 from
referring to __PAGE_OFFSET directly as a symbol which doesn't work
when the kernel identity mapping base is randomized, in which case
__PAGE_OFFSET is a variable (Rafael Wysocki).
- Avoid selecting CPU_FREQ_STAT by default as the statistics are not
required for proper cpufreq operation (Borislav Petkov).
- Add Skylake-X and Broadwell-X IDs to the intel_pstate's list of
processors where out-of-band (OBB) control of P-states is possible
and if that is in use, intel_pstate should not attempt to manage
P-states (Srinivas Pandruvada).
- Drop some unnecessary checks from the wakeup IRQ handling code in
the PM core (Markus Elfring).
- Reduce the number operating performance point (OPP) lookups in
one of the OPP framework's helper functions (Jisheng Zhang).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=WvPB
-----END PGP SIGNATURE-----
Merge tag 'pm-extra-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more power management updates from Rafael Wysocki:
"A few more fixes and cleanups in the x86-64 low-level hibernation
code, PM core, cpufreq (Kconfig and intel_pstate), and the operating
points framework.
Specifics:
- Prevent the low-level assembly hibernate code on x86-64 from
referring to __PAGE_OFFSET directly as a symbol which doesn't work
when the kernel identity mapping base is randomized, in which case
__PAGE_OFFSET is a variable (Rafael Wysocki).
- Avoid selecting CPU_FREQ_STAT by default as the statistics are not
required for proper cpufreq operation (Borislav Petkov).
- Add Skylake-X and Broadwell-X IDs to the intel_pstate's list of
processors where out-of-band (OBB) control of P-states is possible
and if that is in use, intel_pstate should not attempt to manage
P-states (Srinivas Pandruvada).
- Drop some unnecessary checks from the wakeup IRQ handling code in
the PM core (Markus Elfring).
- Reduce the number operating performance point (OPP) lookups in one
of the OPP framework's helper functions (Jisheng Zhang)"
* tag 'pm-extra-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
x86/power/64: Do not refer to __PAGE_OFFSET from assembly code
cpufreq: Do not default-yes CPU_FREQ_STAT
cpufreq: intel_pstate: Add more out-of-band IDs
PM / OPP: optimize dev_pm_opp_set_rate() performance a bit
PM-wakeup: Delete unnecessary checks before three function calls
Cleanups:
- huge cleanup of rtc-generic and char/genrtc this allowed to cleanup rtc-cmos,
rtc-sh, rtc-m68k, rtc-powerpc and rtc-parisc
- move mn10300 to rtc-cmos
Subsystem:
- fix wakealarms after hibernate
- multiples fixes for rctest
- simplify implementations of .read_alarm
New drivers:
- Maxim MAX6916
Drivers:
- ds1307: fix weekday
- m41t80: add wakeup support
- pcf85063: add support for PCF85063A variant
- rv8803: extend i2c fix and other fixes
- s35390a: fix alarm reading, this fixes instant reboot after shutdown for QNAP
TS-41x
- s3c: clock fixes
-----BEGIN PGP SIGNATURE-----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=rpGB
-----END PGP SIGNATURE-----
Merge tag 'rtc-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"RTC for 4.8
Cleanups:
- huge cleanup of rtc-generic and char/genrtc this allowed to cleanup
rtc-cmos, rtc-sh, rtc-m68k, rtc-powerpc and rtc-parisc
- move mn10300 to rtc-cmos
Subsystem:
- fix wakealarms after hibernate
- multiples fixes for rctest
- simplify implementations of .read_alarm
New drivers:
- Maxim MAX6916
Drivers:
- ds1307: fix weekday
- m41t80: add wakeup support
- pcf85063: add support for PCF85063A variant
- rv8803: extend i2c fix and other fixes
- s35390a: fix alarm reading, this fixes instant reboot after
shutdown for QNAP TS-41x
- s3c: clock fixes"
* tag 'rtc-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (65 commits)
rtc: rv8803: Clear V1F when setting the time
rtc: rv8803: Stop the clock while setting the time
rtc: rv8803: Always apply the I²C workaround
rtc: rv8803: Fix read day of week
rtc: rv8803: Remove the check for valid time
rtc: rv8803: Kconfig: Indicate rx8900 support
rtc: asm9260: remove .owner field for driver
rtc: at91sam9: Fix missing spin_lock_init()
rtc: m41t80: add suspend handlers for alarm IRQ
rtc: m41t80: make it a real error message
rtc: pcf85063: Add support for the PCF85063A device
rtc: pcf85063: fix year range
rtc: hym8563: in .read_alarm set .tm_sec to 0 to signal minute accuracy
rtc: explicitly set tm_sec = 0 for drivers with minute accurancy
rtc: s3c: Add s3c_rtc_{enable/disable}_clk in s3c_rtc_setfreq()
rtc: s3c: Remove unnecessary call to disable already disabled clock
rtc: abx80x: use devm_add_action_or_reset()
rtc: m41t80: use devm_add_action_or_reset()
rtc: fix a typo and reduce three empty lines to one
rtc: s35390a: improve two comments in .set_alarm
...
* pm-sleep:
x86/power/64: Do not refer to __PAGE_OFFSET from assembly code
* pm-cpufreq:
cpufreq: Do not default-yes CPU_FREQ_STAT
cpufreq: intel_pstate: Add more out-of-band IDs
* pm-core:
PM-wakeup: Delete unnecessary checks before three function calls
* pm-opp:
PM / OPP: optimize dev_pm_opp_set_rate() performance a bit
In dev_pm_opp_set_rate(), _find_opp_table() is called 4 times: once by
_get_opp_clk(), once by dev_pm_opp_set_rate() itself, and twice by
dev_pm_opp_find_freq_ceil(). If there are several opp_tables in the
system, three times of opp table finding is a big waste. This patch
reduced the call of _find_opp_table() to twice.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The following functions test whether their argument is NULL
and then return immediately.
* dev_pm_arm_wake_irq
* dev_pm_disarm_wake_irq
* wakeup_source_unregister
Thus the test around the calls is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Pavel Machek <pavel@ucw.cz>
[ rjw: Minor whitespace adjustments ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* pm-core:
PM / runtime: Asynchronous "idle" in pm_runtime_allow()
PM / runtime: print error when activating a child to unactive parent
* pm-clk:
PM / clk: Add support for adding a specific clock from device-tree
PM / clk: export symbols for existing pm_clk_<...> API fcns
* pm-domains:
PM / Domains: Convert pm_genpd_init() to return an error code
PM / Domains: Stop/start devices during system PM suspend/resume in genpd
PM / Domains: Allow runtime PM during system PM phases
PM / Runtime: Avoid resuming devices again in pm_runtime_force_resume()
PM / Domains: Remove redundant pm_request_idle() call in genpd
PM / Domains: Remove redundant wrapper functions for system PM
PM / Domains: Allow genpd to power on during system PM phases
* pm-pci:
PCI / PM: check all fields in pci_set_platform_pm()
Arjan reports that it takes a relatively long time to enable runtime
PM for multiple devices at system startup, because all writes to the
"control" attribute in sysfs are handled synchronously and if the
device is suspended as a result of the write, it will block until
that operation is complete.
That may be avoided by passing the RPM_ASYNC flag to rpm_idle()
in pm_runtime_allow() which will make it execute the device's
"idle" callback asynchronously, so writes to "control" changing
it from "on" to "auto" will return without waiting.
Reported-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
The are already cases when pm_genpd_init() can fail. Currently we hide the
failures instead of propagating an error code, which is a better method.
Moreover, to prepare for future changes like moving away from using a
fixed array-size of the struct genpd_power_state, to instead dynamically
allocate data for it, the pm_genpd_init() API needs to be able to return
an error code, as allocation can fail.
Current users of the pm_genpd_init() is thus requested to start dealing
with error codes. In the transition phase, users will have to live with
only error messages being printed to log.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Some drivers using the PM clocks framework need to add specific clocks
from device-tree using a name by calling the functions
of_clk_get_by_name() and then pm_clk_add_clk(). Rather than having
drivers call both functions, add a helper function of_pm_clk_add_clk()
that will call these functions so drivers can call a single function
to add a specific clock from device-tree.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The code currently silently bails out with -EBUSY if you try to
activate a child to an inactive parent.
This typically happens when you have a runtime suspended parent
and runtime resume your child, but forgot to set .ignore_children
on the parent to true with pm_suspend_ignore_children(dev).
Silently ignoring this error is not good as it gives rise to
other strange behaviour like double-resume of devices after
silently bailing out of the .runtime_resume() callback.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
dev_pm_opp_get_sharing_cpus() returns 0 even in the case when the OPP
core doesn't know whether or not the table is shared. It works on the
majority of platforms, where the OPP table is never created before
invoking the function and then -ENODEV is returned by it.
But in the case of one platform (Jetson TK1) at least, the situation
is a bit different. The OPP table has been created (somehow) before
dev_pm_opp_get_sharing_cpus() is called and it returns 0. Its caller
treats that as 'the CPUs don't share OPPs' and that leads to degraded
performance.
Fix this by converting 'shared_opp' in struct opp_table to an enum
and making dev_pm_opp_get_sharing_cpus() return -EINVAL in case when
the value of that field is "access unknown", so that the caller can
handle it accordingly (cpufreq-dt considers that as 'all CPUs share
the table', for example).
Fixes: 6f707daa38 "PM / OPP: Add dev_pm_opp_get_sharing_cpus()"
Reported-and-tested-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
[ rjw : Subject & changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Not all subsystems/drivers that manages devices attached to a genpd
makes use of the pm_runtime_force_suspend|resume() helper functions
to deal with system PM suspend/resume.
In cases like these and when genpd's ->stop|start() callbacks are
used for the device, invoke the pm_runtime_force_suspend|resume()
helper functions from genpd's "noirq" system PM callbacks. In this
way we make sure to "stop" the device on suspend and to "start" it
on resume.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In cases when a PM domain isn't powered off when genpd's ->prepare()
callback is invoked, genpd runtime resumes and disables runtime PM for the
device. This behaviour was needed when genpd managed intermediate states
during the power off sequence, as to maintain proper low power states of
devices during system PM suspend/resume.
Commit ba2bbfbf63 (PM / Domains: Remove intermediate states from the
power off sequence), enables genpd to improve its behaviour in that
respect.
The PM core disables runtime PM at __device_suspend_late() before it calls
a system PM "late" callback for a device. When resuming a device, after a
corresponding "early" callback has been invoked, the PM core re-enables
runtime PM.
By changing genpd to allow runtime PM according to the same system PM
phases as the PM core, devices can be runtime resumed by their
corresponding subsystem/driver when really needed.
In this way, genpd no longer need to runtime resume the device from its
->prepare() callback. In most cases that avoids unnecessary and energy-
wasting operations of runtime resuming devices that have nothing to do,
only to runtime suspend them shortly after.
Although, because of changing this behaviour in genpd and due to that
genpd powers on the PM domain unconditionally in the system PM resume
"noirq" phase, it could potentially cause a PM domain to stay powered
on even if it's unused after the system has resumed. To avoid this,
schedule a power off work when genpd's system PM ->complete() callback
has been invoked for the last device in the PM domain.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
If the runtime PM status of the device isn't RPM_SUSPENDED, prevent the
pm_runtime_force_resume() from invoking the ->runtime_resume() callback
for the device, as it's not the expected behaviour from the subsystem/driver.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The PM core increases the runtime PM usage count at the system PM prepare
phase. Later when the system resumes, it does a pm_runtime_put() in the
complete phase, which in addition to decrementing the usage count, does
the equivalent of a pm_request_idle().
Therefore the call to pm_request_idle() from within genpd's ->complete()
callback is redundant, so remove it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Due to the previous changes in genpd, which removed the suspend_power_off
flag, several of the system PM callbacks no longer do any additional
checks but only invoke corresponding pm_generic_* helper functions.
To clean up the code, drop these wrapper functions as they have
become redundant. Instead, assign the system PM callbacks directly
to the pm_generic_*() helper functions.
While changing this, it has bocame clear that some of the current
system PM callbacks in genpd invoke wrong driver callbacks. For
example, the genpd's ->restore() callback invokes pm_generic_resume(),
while that should be pm_generic_restore(). Fix that as well.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
If a PM domain is powered off when the first device starts its system PM
prepare phase, genpd prevents any further attempts to power on the PM
domain during the following system PM phases. Not until the system PM
complete phase is finalized for all devices in the PM domain, genpd again
allows it to be powered on.
This behaviour needs to be changed, as a subsystem/driver for a device in
the same PM domain may still need to be able to serve requests in some of
the system PM phases. Accordingly, it may need to runtime resume its
device and thus also request the corresponding PM domain to be powered on.
To deal with these scenarios, let's make the device operational in the
system PM prepare phase by runtime resuming it, no matter if the PM domain
is powered on or off. Changing this also enables us to remove genpd's
suspend_power_off flag, as it's being used to track this condition.
Additionally, we must allow the PM domain to be powered on via runtime PM
during the system PM phases.
This change also requires a fix in the AMD ACP (Audio CoProcessor) drm
driver. It registers a genpd to model the ACP as a PM domain, but
unfortunately it's also abuses genpd's "internal" suspend_power_off flag
to deal with a corner case at system PM resume.
More precisely, the so called SMU block powers on the ACP at system PM
resume, unconditionally if it's being used or not. This may lead to that
genpd's internal status of the power state, may not correctly reflect the
power state of the HW after a system PM resume.
Because of changing the behaviour of genpd, by runtime resuming devices in
the prepare phase, the AMD ACP drm driver no longer have to deal with this
corner case. So let's just drop the related code in this driver.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Acked-by: Maruthi Bayyavarapu <maruthi.bayyavarapu@amd.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
While trying to convert a DMA driver from bool to tristate, we
encountered the following:
ERROR: "pm_clk_add_clk" [drivers/dma/tegra210-adma.ko] undefined!
ERROR: "pm_clk_create" [drivers/dma/tegra210-adma.ko] undefined!
ERROR: "pm_clk_destroy" [drivers/dma/tegra210-adma.ko] undefined!
ERROR: "pm_clk_suspend" [drivers/dma/tegra210-adma.ko] undefined!
ERROR: "pm_clk_resume" [drivers/dma/tegra210-adma.ko] undefined!
Since in principle there is nothing preventing these functions
from being used in modular code as well as builtin, we add the
export of them. We expand the scope to also include:
pm_clk_add
of_pm_clk_add_clks
pm_clk_remove
pm_clk_remove_clk
pm_clk_init
pm_clk_runtime_suspend
pm_clk_runtime_resume
pm_clk_add_notifier
...since these functions are also non-static and presumably form
part of the existing API used by other drivers that may become
modular in the future.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit 3195ef59cb ("x86: Do full rtc synchronization with ntp") had
the side-effect of unconditionally enabling the RTC_LIB symbol on x86,
which in turn disables the selection of the CONFIG_RTC and
CONFIG_GEN_RTC drivers that contain a two older implementations of
the CONFIG_RTC_DRV_CMOS driver.
This removes x86 from the list for genrtc, and changes all references
to the asm/rtc.h header to instead point to the interfaces
from linux/mc146818rtc.h.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Grygorii Strashko reports:
The PM runtime will be left disabled for the device if its
.suspend_late() callback fails and async suspend is not allowed
for this device. In this case device will not be added in
dpm_late_early_list and dpm_resume_early() will ignore this
device, as result PM runtime will be disabled for it forever
(side effect: after 8 subsequent failures for the same device
the PM runtime will be reenabled due to disable_depth overflow).
To fix this problem, add devices to dpm_late_early_list regardless
of whether or not device_suspend_late() returns errors for them.
That will ensure failures in there to be handled consistently for
all devices regardless of their async suspend/resume status.
Reported-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: All applicable <stable@vger.kernel.org>
Recently, a few issues were noticed in the code where CONFIG_OF wasn't
consistently used for many routines. The core file is big enough now and
ifdef hackery makes it less readable.
Move OF-specific code to another file and compile that only if CONFIG_OF
is enabled.
Compile-tested:
- For ARM (exynos) with CONFIG_OF enabled
- For X86 with CONFIG_OF disabled (have to enable CONFIG_PM_OPP separately)
No functional changes.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Regulators are optional for devices using OPPs and the OPP core
shouldn't be printing any errors for such missing regulators.
It was fine before the commit 0c717d0f9c, but that failed to update
this part of the code to remove an 'always true' check and an extra
unwanted print message.
Fix that now.
Fixes: 0c717d0f9c (PM / OPP: Initialize regulator pointer to an error value)
Reported-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Functions dev_pm_opp_of_{cpumask_,}remove_table removes/frees all the
static OPP entries associated with the device and/or all cpus(in case
of cpumask) that are created from DT.
However the OPP entries are populated reading from the firmware or some
different method using dev_pm_opp_add are marked dynamic and can't be
removed using above functions.
This patch adds non DT/OF versions of dev_pm_opp_{cpumask_,}remove_table
to support the above mentioned usecase.
This is in preparation to make use of the same in scpi-cpufreq.c
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The new use of dev_pm_opp_set_sharing_cpus resulted in a harmless compiler
warning with CONFIG_CPUMASK_OFFSTACK=y:
drivers/cpufreq/mvebu-cpufreq.c: In function 'armada_xp_pmsu_cpufreq_init':
include/linux/cpumask.h:550:25: error: passing argument 2 of 'dev_pm_opp_set_sharing_cpus' discards 'const' qualifier from pointer target type [-Werror=discarded-qualifiers]
The problem here is that cpumask_var_t gets passed by reference, but
by declaring a 'const cpumask_var_t' argument, only the pointer is
constant, not the actual mask. This is harmless because the function
does not actually modify the mask.
This patch changes the function prototypes for all of the related functions
to pass a 'struct cpumask *' instead of 'cpumask_var_t', matching what
most other such functions do in the kernel. This lets us mark all the
other similar functions as taking a 'const' mask where possible,
and it avoids the warning without any change in object code.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 947bd567f7 (mvebu: Use dev_pm_opp_set_sharing_cpus() to mark OPP tables as shared)
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
OPP core allows a platform to mark OPP table as shared, when the
platform isn't using operating-points-v2 bindings.
And, so there should be a non DT way of finding out if the OPP table is
shared or not.
This patch adds dev_pm_opp_get_sharing_cpus(), which first tries to get
OPP sharing information from the opp-table (in case it is already marked
as shared), otherwise it uses the existing DT way of finding sharing
information.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
dev_pm_opp_set_sharing_cpus() isn't supposed to update the cpumask
passed as its parameter, and so it should always have been marked
'const'.
Do it now.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit 32e8d689dc (PM / sleep: trace_device_pm_callback coverage in
dpm_prepare/complete) removed all users of this variable but forgot to
remove the variable itself.
Signed-off-by: Thierry Reding <treding@nvidia.com>
[ rjw: Subject ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
As the PM core already have wakeup management during the system PM phase,
it seems reasonable that genpd and its users should be able to rely on
that. Therefore let's remove this from pm_genpd_prepare().
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The PM core increases and decreases the runtime PM usage count in the
system PM prepare phase. This makes some of the pm_runtime_get|put*()
calls in pm_genpd_prepare() redundant, so let's remove them.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
It is entirely possible for of_count_phandle_wit_args to
return a -ve error return value so we need to check for this
otherwise we end up allocating a negative number of clk objects.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
opp core allows OPPs to be explicitly marked as shared from platform
code, in case of operating-point v1 bindings.
Though we do everything fine in that case, we don't set the flag in the
opp-table to indicate that the OPPs are shared. It works fine today as
the flag isn't used anywhere else in the core, but we should be doing
the right thing by marking it set.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Move dev_pm_opp_set_sharing_cpus() towards the end of the file. This
is required for better readability after the next patch is applied,
which adds dev_pm_opp_get_sharing_cpus().
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Few of the routines in cpu.c were missing these, add them.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Don't send -EINVAL and propagate what's received from _find_opp_table().
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
As a part of the ongoing consolidation of genpd, it's become questionable
whether clients actually needs to be able to assign their own set of
->save|restore_state() callbacks. Currently all users copes fine with the
default callbacks, so let's remove the configuration option and stick to
the default ones.
This enables further clarifications of the related code and let's also
rename pm_genpd_default_save|restore_state() into
__genpd_runtime_suspend|resume() to apply the rule of static functionnames
in genpd.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Follow genpd's rule for names of static functions, by renaming
pm_genpd_runtime_suspend|resume() to genpd_runtime_suspend|resume().
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The genpd governor validates the latency constraints to find out whether
it's acceptable to runtime suspend a device. Earlier this validation was
made to know whether it was okay to invoke the ->stop() callback for the
device, hence the governor used the name "stop_ok" for the related
variables.
To clarify the code around this, let's rename these variables from
"stop_ok" to "suspend_ok".
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
As pm_runtime_set_active() may fail because the device's parent isn't
active, we can end up executing the ->runtime_resume() callback for the
device when it isn't allowed.
Fix this by invoking pm_runtime_set_active() before running the callback
and let's also deal with the error code.
Fixes: 37f204164d (PM: Add pm_runtime_suspend|resume_force functions)
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: 3.15+ <stable@vger.kernel.org> # 3.15+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Now wakeirq stops working for device if wakeup option for
this device will be reconfigured through sysfs, like:
echo disabled > /sys/devices/platform/extcon_usb1/power/wakeup
echo enabled > /sys/devices/platform/extcon_usb1/power/wakeup
Once above set of commands is executed the device's wakeup_source
opject will be recreated and dev->power.wakeup->wakeirq field will
contain NULL. As result, device_wakeup_arm_wake_irqs() will not arm
wakeirq for the affected device.
Hece, lets try to fix it in the following way:
check for dev->wakeirq field when device_wakeup_attach() is called
and if !NULL re-attach wakeirq to the device
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The PM clocks framework requires clients to pass either a con-id or a
valid clk pointer in order to add a clock to a device. Add a new
function of_pm_clk_add_clks() to allows device clocks to be retrieved
from device-tree and populated for a given device. Note that it is
not necessary to make the compilation of this new function dependent
upon CONFIG_OF because there are stubs functions for the device-tree
APIs used.
In order to handle errors encountered when adding clocks from
device-tree, add a function pm_clk_remove_clk() to remove any clocks
(using a pointer to the clk structure) that have been added
successfully before the error occurred.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In the function of_genpd_get_from_provider(), we never check to see if
the argument 'genpdspec' is NULL before dereferencing it. Add error
checking to handle any NULL pointers.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit 30e7a65b3f (PM / Domains: Ensure subdomain is not in use
before removing) added a test to ensure that a subdomain is not a
master to another subdomain or if any devices are using the subdomain
before removing. This change incorrectly used the "slave_links" list to
determine if the subdomain is a master to another subdomain, where it
should have been using the "master_links" list instead. The
"slave_links" list will never be empty for a subdomain and so a
subdomain can never be removed. Fix this by testing if the
"master_links" list is empty instead.
Fixes: 30e7a65b3f (PM / Domains: Ensure subdomain is not in use before removing)
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
During runtime resume the return values of the start and restore steps
are ignored. As a result drivers are not notified of runtime resume
failures and can't propagate them up. Fix it by returning an error if
either the start or restore step fails, and clean up properly in the
error path.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
For low-power states, the state index is part of the state, hence join
them with a hyphen in the /sys/kernel/debug/pm_genpd/pm_genpd_summary
output. E.g. "off 0" becomes "off-0".
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The slave domains are no longer aligned with the table header in the
/sys/kernel/debug/pm_genpd/pm_genpd_summary output. Worse, the alignment
differs depending on the actual name of the state.
Format the state name and index into a buffer, and print that like
before to restore alignment.
Use "%u" for unsigned int while we're at it.
Fixes: fc5cbf0c94 (PM / Domains: Support for multiple states)
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Stephen pointed out recently, that few structures always confuse him as
they aren't named properly. And this patch tries to address that:
Names are updated as:
- device_opp or dev_opp -> opp_table
- dev_opp_list -> opp_tables
- dev_opp_list_lock -> opp_table_lock
- device_list_opp -> opp_device (it was never a list, but a structure)
- list_dev -> opp_dev
- And similar changes in comments and function names as well.
This also fixes checkpatch warnings that were generated with this patch.
No functional changes.
Suggested-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Some comments were just copy/pasted from other sections and don't match
to the routines they were added for. Fix them.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
We are currently required to do two checks for regulator pointer:
IS_ERR() and IS_NULL().
And multiple instances are reported, about both of these not being used
consistently and so resulting in crashes.
Fix that by initializing regulator pointer with an error value and
checking it only against an error.
This makes code more consistent and more efficient.
Fixes: 7d34d56ef3 (PM / OPP: Disable OPPs that aren't supported by the regulator)
Reported-and-tested-by: Jon Hunter <jonathanh@nvidia.com>
Reported-and-tested-by: Tony Lindgren <tony@atomide.com>
Reported-and-tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
[ rjw: Initialize to -ENXIO ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Now that all known users have been converted to use state latencies,
we can remove the latency field in the generic_pm_domain structure.
Signed-off-by: Axel Haslam <ahaslam+renesas@baylibre.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Some hardware (eg. OMAP), has the ability to enter different low power
modes for a given power domain. This allows for more fine grained control
over the power state of the platform. As a typical example, some registers
of the hardware may be implemented with retention flip-flops and be able
to retain their state at lower voltages allowing for faster on/off
latencies and an increased window of opportunity to enter an intermediate
low power state other than "off"
When trying to set a power domain to off, the genpd governor will choose
the deepest state that will respect the qos constraints of all the devices
and sub-domains on the power domain. The state chosen by the governor is
saved in the "state_idx" field of the generic_pm_domain structure and
shall be used by the power_off and power_on callbacks to perform the
necessary actions to set the power domain into (and out of) the state
indicated by state_idx.
States must be declared in ascending order from shallowest to deepest,
deepest meaning the state which takes longer to enter and exit.
For platforms that don't declare any states, a single a single "off"
state is used. Once all platforms are converted to use the state array,
the legacy on/off latencies will be removed.
[ Lina: Modified genpd state initialization and remove use of
save_state_latency_ns in genpd timing data ]
Suggested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Lina Iyer <lina.iyer@linaro.org>
Signed-off-by: Axel Haslam <ahaslam+renesas@baylibre.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
We kept u_volt_min/max initialized to 0, when only the target voltage is
present in DT, instead of the target/min/max triplet.
This didn't go well with the regulator framework, as on few calls the
min voltage was set to target and max was set to 0 and so resulted in a
kernel crash like below:
kernel BUG at ../drivers/regulator/core.c:216!
[<c0684af4>] (regulator_check_voltage) from [<c06857ac>] (regulator_set_voltage_unlocked+0x58/0x230)
[<c06857ac>] (regulator_set_voltage_unlocked) from [<c06859ac>] (regulator_set_voltage+0x28/0x54)
[<c06859ac>] (regulator_set_voltage) from [<c0775b28>] (_set_opp_voltage+0x30/0x98)
[<c0775b28>] (_set_opp_voltage) from [<c0776630>] (dev_pm_opp_set_rate+0xf0/0x28c)
[<c0776630>] (dev_pm_opp_set_rate) from [<c096f784>] (__cpufreq_driver_target+0x184/0x2b4)
[<c096f784>] (__cpufreq_driver_target) from [<c0973760>] (dbs_check_cpu+0x1b0/0x1f4)
[<c0973760>] (dbs_check_cpu) from [<c0973f30>] (cpufreq_governor_dbs+0x324/0x5c4)
[<c0973f30>] (cpufreq_governor_dbs) from [<c0970958>] (__cpufreq_governor+0xe4/0x1ec)
[<c0970958>] (__cpufreq_governor) from [<c09711e0>] (cpufreq_init_policy+0x64/0x8c)
[<c09711e0>] (cpufreq_init_policy) from [<c09718cc>] (cpufreq_online+0x2fc/0x708)
[<c09718cc>] (cpufreq_online) from [<c0765ff0>] (subsys_interface_register+0x94/0xd8)
[<c0765ff0>] (subsys_interface_register) from [<c0970530>] (cpufreq_register_driver+0x14c/0x19c)
[<c0970530>] (cpufreq_register_driver) from [<c09746dc>] (dt_cpufreq_probe+0x70/0xec)
[<c09746dc>] (dt_cpufreq_probe) from [<c076907c>] (platform_drv_probe+0x4c/0xb0)
[<c076907c>] (platform_drv_probe) from [<c07678e0>] (driver_probe_device+0x214/0x2c0)
[<c07678e0>] (driver_probe_device) from [<c0767a18>] (__driver_attach+0x8c/0x90)
[<c0767a18>] (__driver_attach) from [<c0765c2c>] (bus_for_each_dev+0x68/0x9c)
[<c0765c2c>] (bus_for_each_dev) from [<c0766d78>] (bus_add_driver+0x1a0/0x218)
[<c0766d78>] (bus_add_driver) from [<c076810c>] (driver_register+0x78/0xf8)
[<c076810c>] (driver_register) from [<c0301d74>] (do_one_initcall+0x90/0x1d8)
[<c0301d74>] (do_one_initcall) from [<c1100e14>] (kernel_init_freeable+0x15c/0x1fc)
[<c1100e14>] (kernel_init_freeable) from [<c0b27a0c>] (kernel_init+0x8/0xf0)
[<c0b27a0c>] (kernel_init) from [<c0307d78>] (ret_from_fork+0x14/0x3c)
Code: e1550004 baffffeb e3a00000 e8bd8070 (e7f001f2)
Fix that by initializing u_volt_min/max to the target voltage in such cases.
Reported-and-tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Fixes: 274659029c (PM / OPP: Add support to parse "operating-points-v2" bindings)
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit 7d34d56ef3 (PM / OPP: Disable OPPs that aren't supported by
the regulator) causes a crash to happen on Tegra124 Jetson TK1 when
using the DFLL clock source for the CPU. The DFLL manages the voltage
itself and so there is no regulator specified for the OPPs and so we
get a crash when we try to dereference the regulator pointer. Fix
this by checking to see if the regulator IS_ERR_OR_NULL before
dereferencing it.
Fixes: 7d34d56ef3 (PM / OPP: Disable OPPs that aren't supported by the regulator)
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Reported-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
[ rjw: Changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Accessing more than one byte from a symbol declared simply 'char' is undefined
behavior, as reported by UBSAN:
UBSAN: Undefined behaviour in drivers/base/power/trace.c:178:18
load of address ffffffff8203fc78 with insufficient space
for an object of type 'char'
Avoid this by declaring the symbols as arrays.
Signed-off-by: Eric Biggers <ebiggers3@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This adds a routine, dev_pm_opp_set_rate(), responsible for configuring
power-supply and clock source for an OPP.
The OPP is found by matching against the target_freq passed to the
routine. This shall replace similar code present in most of the OPP
users and help simplify them a lot.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
OPP core has got almost everything now to manage device's OPP
transitions, the only thing left is device's clk. Get that as well.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
V2 bindings have better support for clock-latency and voltage-tolerance
and doesn't need special care. To use callbacks, like
dev_pm_opp_get_max_{transition|volt}_latency(), irrespective of the
bindings, the core needs to know clock-latency/voltage-tolerance for the
earlier bindings.
This patch reads clock-latency/voltage-tolerance from the device node,
irrespective of the bindings (to keep it simple) and use them only for
V1 bindings.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In few use cases (like: cpufreq), it is desired to get the maximum
latency for changing OPPs. Add support for that.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In few use cases (like: cpufreq), it is desired to get the maximum
voltage latency for changing OPPs. Add support for that.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Disable any OPPs where the connected regulator isn't able to provide the
specified voltage.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This allows the OPP core to request/free the regulator resource,
attached to a device OPP. The regulator device is fetched using the name
provided by the driver, while calling: dev_pm_opp_set_regulator().
This will work for both OPP-v1 and v2 bindings.
This is a preliminary step for moving the OPP switching logic into the
OPP core.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* pm-core:
PM: Avoid false-positive warnings in dev_pm_domain_set()
ACPI / LPSS: set PM domain via helper setter
* pm-domains:
PM / Domains: Silence compiler warning for an unused function
There is a WARN_ON() in dev_pm_domain_set() that triggers on attempts
to set the pm_domain pointer for devices with a driver bound.
However, that WARN_ON() triggers on attempts to clear the pointer
too and the test it uses is based on checking the device's
p->knode_driver pointer which still is set when the device bus
type's/driver's ->remove callback has been executed. This
leads to false-positive warnings when bus type code calls
dev_pm_domain_set() to clear the pm_domain pointer after
invoking the driver's ->remove() callback.
To avoid those false-positives, make dev_pm_domain_set() check
if the pointer passed to it is NULL and skip the warning in
that case.
Fixes: 989561de9b (PM / Domains: add setter for dev.pm_domain)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Sinan Kaya <okaya@codeaurora.org>
Tested-by: Steven Rostedt <rostedt@goodmis.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
The only remaining caller of genpd_poweron() is conditionally compiled
based on CONFIG_PM_GENERIC_DOMAINS_OF, so we get a warning when that is
unset.
By moving the locking/unlocking of the genpd outside genpd_poweron(), thus
to the caller, genpd_poweron() becomes redundant.
Within this context let's then rename the wrapper function,
__genpd_poweron(), to genpd_poweron() as it will then be consistent with
its friend genpd_poweroff().
This change silence the warning about the unused function.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Fixes: ea823c7cbf "PM / Domains: Remove pm_genpd_poweron() API"
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: 4.4+ <stable@vger.kernel.org> # 4.4+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* pm-cpuidle:
cpuidle: coupled: remove unused define cpuidle_coupled_lock
cpuidle: fix fallback mechanism for suspend to idle in absence of enter_freeze
* pm-cpufreq:
cpufreq: cpufreq-dt: avoid uninitialized variable warnings:
cpufreq: pxa2xx: fix pxa_cpufreq_change_voltage prototype
cpufreq: Use list_is_last() to check last entry of the policy list
cpufreq: Fix NULL reference crash while accessing policy->governor_data
* pm-domains:
PM / Domains: Fix typo in comment
PM / Domains: Fix potential deadlock while adding/removing subdomains
PM / domains: fix lockdep issue for all subdomains
* pm-sleep:
PM: APM_EMULATION does not depend on PM
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
We must preserve the same order of how we acquire and release the lock for
genpd, as otherwise we may encounter deadlocks.
The power on phase of a genpd starts by acquiring its lock. Then it walks
the hierarchy of its parent domains to be able to power on these first, as
per design of genpd.
From a locking perspective this means the locks of the parents becomes
acquired after the lock of the subdomain.
Let's fix pm_genpd_add|remove_subdomain() to maintain the same order of
acquiring/releasing the genpd lock as being applied in the power on/off
sequence.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
During genpd_poweron, genpd->lock is acquired recursively for each
parent (master) domain, which are separate objects. This confuses
lockdep, which considers every operation on genpd->lock as being done on
the same lock class. This leads to the following false positive warning:
=============================================
[ INFO: possible recursive locking detected ]
4.4.0-rc4-xu3s #32 Not tainted
---------------------------------------------
swapper/0/1 is trying to acquire lock:
(&genpd->lock){+.+...}, at: [<c0361550>] __genpd_poweron+0x64/0x108
but task is already holding lock:
(&genpd->lock){+.+...}, at: [<c0361af8>] genpd_dev_pm_attach+0x168/0x1b8
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&genpd->lock);
lock(&genpd->lock);
*** DEADLOCK ***
May be due to missing lock nesting notation
3 locks held by swapper/0/1:
#0: (&dev->mutex){......}, at: [<c0350910>] __driver_attach+0x48/0x98
#1: (&dev->mutex){......}, at: [<c0350920>] __driver_attach+0x58/0x98
#2: (&genpd->lock){+.+...}, at: [<c0361af8>] genpd_dev_pm_attach+0x168/0x1b8
stack backtrace:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.4.0-rc4-xu3s #32
Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
[<c0016c98>] (unwind_backtrace) from [<c00139c4>] (show_stack+0x10/0x14)
[<c00139c4>] (show_stack) from [<c0270df0>] (dump_stack+0x84/0xc4)
[<c0270df0>] (dump_stack) from [<c00780b8>] (__lock_acquire+0x1f88/0x215c)
[<c00780b8>] (__lock_acquire) from [<c007886c>] (lock_acquire+0xa4/0xd0)
[<c007886c>] (lock_acquire) from [<c0641f2c>] (mutex_lock_nested+0x70/0x4d4)
[<c0641f2c>] (mutex_lock_nested) from [<c0361550>] (__genpd_poweron+0x64/0x108)
[<c0361550>] (__genpd_poweron) from [<c0361b00>] (genpd_dev_pm_attach+0x170/0x1b8)
[<c0361b00>] (genpd_dev_pm_attach) from [<c03520a8>] (platform_drv_probe+0x2c/0xac)
[<c03520a8>] (platform_drv_probe) from [<c03507d4>] (driver_probe_device+0x208/0x2fc)
[<c03507d4>] (driver_probe_device) from [<c035095c>] (__driver_attach+0x94/0x98)
[<c035095c>] (__driver_attach) from [<c034ec14>] (bus_for_each_dev+0x68/0x9c)
[<c034ec14>] (bus_for_each_dev) from [<c034fec8>] (bus_add_driver+0x1a0/0x218)
[<c034fec8>] (bus_add_driver) from [<c035115c>] (driver_register+0x78/0xf8)
[<c035115c>] (driver_register) from [<c0338488>] (exynos_drm_register_drivers+0x28/0x74)
[<c0338488>] (exynos_drm_register_drivers) from [<c0338594>] (exynos_drm_init+0x6c/0xc4)
[<c0338594>] (exynos_drm_init) from [<c00097f4>] (do_one_initcall+0x90/0x1dc)
[<c00097f4>] (do_one_initcall) from [<c0895e08>] (kernel_init_freeable+0x158/0x1f8)
[<c0895e08>] (kernel_init_freeable) from [<c063ecac>] (kernel_init+0x8/0xe8)
[<c063ecac>] (kernel_init) from [<c000f7d0>] (ret_from_fork+0x14/0x24)
This patch replaces mutex_lock with mutex_lock_nested() and uses
recursion depth to annotate each genpd->lock operation with separate
lockdep subclass.
Reported-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Tested-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* pm-core:
driver core: Avoid NULL pointer dereferences in device_is_bound()
platform: Do not detach from PM domains on shutdown
USB / PM: Allow USB devices to remain runtime-suspended when sleeping
PM / sleep: Go direct_complete if driver has no callbacks
PM / Domains: add setter for dev.pm_domain
device core: add device_is_bound()
* acpi-soc:
PM / clk: don't leave clocks enabled when driver not bound
i2c: dw: Add APM X-Gene ACPI I2C device support
ACPI / APD: Add APM X-Gene ACPI I2C device support
ACPI / LPSS: change 'does not have' to 'has' in comment
Revert "dmaengine: dw: platform: provide platform data for Intel"
dmaengine: dw: return immediately from IRQ when DMA isn't in use
dmaengine: dw: platform: power on device on shutdown
ACPI / LPSS: override power state for LPSS DMA device
ACPI / LPSS: power on when probe() and otherwise when remove()
ACPI / LPSS: do delay for all LPSS devices when D3->D0
ACPI / LPSS: allow to use specific PM domain during ->probe()
Revert "ACPI / LPSS: allow to use specific PM domain during ->probe()"
device core: add BUS_NOTIFY_DRIVER_NOT_BOUND notification
x86/platform/iosf_mbi: Remove duplicate definitions
Conflicts:
drivers/i2c/busses/i2c-designware-platdrv.c
If a suitable prepare callback cannot be found for a given device and
its driver has no PM callbacks at all, assume that it can go direct to
complete when the system goes to sleep.
The reason for this is that there's lots of devices in a system that do
no PM at all and there's no reason for them to prevent their ancestors
to do direct_complete if they can support it.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Adds a function that sets the pointer to dev_pm_domain in struct device
and that warns if the device has already finished probing. The reason
why we want to enforce that is because in the general case that can
cause problems and also that we can simplify code quite a bit if we can
always assume that.
This patch also changes all current code that directly sets the
dev.pm_domain pointer.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There is a new notification BUS_NOTIFY_DRIVER_NOT_BOUND that is issued when
driver fails during binding. In such case pm_clk_notify(), when PM_CLK=n,
leaves clocks enabled. Undo operations that have been done in
BUS_NOTIFY_BIND_DRIVER case.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
sprintf() can access memory outside of the range of the character array,
and is risky in some situations. The driver specified prop_name string
can be longer than NAME_MAX here (only an attacker will do that though)
and so blindly copying it into the character array of size NAME_MAX
isn't safe. Instead we must use snprintf() here.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Set cpu_dev->id in cpumask first when setting up cpumask for CPUs that
share the same OPP table. This might be helpful when handling cpumask
without the original CPU bitfield set.
Signed-off-by: Pi-Cheng Chen <pi-cheng.chen@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The documentation for detach() said attach.
Signed-off-by: Manuel Pégourié-Gonnard <mpg@elzevir.fr>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit 01fb4d3c39 ("PM / OPP: Parse 'opp-<prop>-<name>'
bindings") broke support for parsing standard opp-microvolt and
opp-microamp properties. Fix it by setting 'name' string to
proper value for !prop cases.
Fixes: 01fb4d3c39 ("PM / OPP: Parse 'opp-<prop>-<name> 'bindings")
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Introduce a new runtime PM function, pm_runtime_get_if_in_use(),
that will increment the device's runtime PM usage counter and
return 1 if its status is RPM_ACTIVE and its usage counter
is greater than 0 at the same time (0 will be returned otherwise).
This is useful for things that should only be done if the device
is active (from the runtime PM perspective) and used by somebody
(as indicated by the usage counter) already and they are not worth
bothering otherwise.
Requested-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
OPP bindings (for few properties) allow a platform to choose a
value/range among a set of available options. The options are present as
opp-<prop>-<name>, where the platform needs to supply the <name> string.
The OPP properties which allow such an option are: opp-microvolt and
opp-microamp.
Add support to the OPP-core to parse these bindings, by introducing
dev_pm_opp_{set|put}_prop_name() APIs.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
OPP bindings allow a platform to enable OPPs based on the version of the
hardware they are used for.
Add support to the OPP-core to parse these bindings, by introducing
dev_pm_opp_{set|put}_supported_hw() APIs.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Drivers which can be built as loadable module needs symbols
- pm_genpd_add_device/pm_genpd_remove_device to add/remove devices
to/from genpd. Those drivers create platform devices, which comes
under a powerdomain.
Signed-off-by: Maruthi Bayyavarapu <maruthi.bayyavarapu@amd.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
A runtime PM centric subsystem/driver may typically use the runtime PM
helpers, pm_runtime_force_suspend|resume() in the system PM path. This
means the genpd's runtime PM callbacks might be invoked even when runtime
PM has been disabled for the device.
To properly cope with these and similar scenarios when these helper
functions are used, change genpd to skip validating and measuring the
device PM QOS latency.
This is needed because otherwise genpd may prevent the device to be put
into low power state. If this occurs during system PM, it causes the
sequence to be aborted as a device's system PM callback returns -EBUSY.
Fixes: ba2bbfbf63 (PM / Domains: Remove intermediate states from the power off sequence)
Reported-by: Cao Minh Hiep <cm-hiep@jinso.co.jp>
Reported-by: Harunaga <nx-truong@jinso.co.jp>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Cc: 4.3+ <stable@vger.kernel.org> # 4.3+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* pm-domains:
PM / Domains: Fix bad of_node_put() in failure paths of genpd_dev_pm_attach()
PM / Domains: Validate cases of a non-bound driver in genpd governor
* pm-cpufreq:
cpufreq: use last policy after online for drivers with ->setpolicy
It looks like these meant to be unreffing the
of_parse_phandle_with_args() node, since the error paths above it
don't do of_node_put. That function returns a new ref in pd_args.np,
though, not a new ref on dev->of_node. Also, it would have leaked the
ref in the success case.
Fixes "ERROR: Bad of_node_put()" on bcm2835 in the -EPROBE_DEFER case.
Fixes: aa42240ab2 (PM / Domains: Add generic OF-based PM domain look-up)
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Kevin Hilman <khilman@linaro.org>
Cc: 3.18+ <stable@vger.kernel.org> # 3.18+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Recently genpd removed the requirement of a having a driver bound for its
attached devices to allow genpd to power off. That change should also have
removed a corresponding validation in the governor, let's correct that.
Fixes: 298cd0f088 (PM / Domains: Remove dev->driver check for runtime)
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There are two common expectations among several subsystems/drivers that
deploys runtime PM support, but which isn't met by the driver core.
Expectation 1)
At ->probe() the subsystem/driver expects the runtime PM status of the
device to be RPM_SUSPENDED, which is the initial status being assigned at
device registration.
This expectation is especially common among some of those subsystems/
drivers that manages devices with an attached PM domain, as those requires
the ->runtime_resume() callback at the PM domain level to be invoked
during ->probe().
Moreover these subsystems/drivers entirely relies on runtime PM resources
being managed at the PM domain level, thus don't implement their own set
of runtime PM callbacks.
These are two scenarios that suffers from this unmet expectation.
i) A failed ->probe() sequence requests probe deferral:
->probe()
...
pm_runtime_enable()
pm_runtime_get_sync()
...
err:
pm_runtime_put()
pm_runtime_disable()
...
As there are no guarantees that such sequence turns the runtime PM status
of the device into RPM_SUSPENDED, the re-trying ->probe() may start with
the status in RPM_ACTIVE.
In such case the runtime PM core won't invoke the ->runtime_resume()
callback because of a pm_runtime_get_sync(), as it considers the device to
be already runtime resumed.
ii) A driver re-bind sequence:
At driver unbind, the subsystem/driver's >remove() callback invokes a
sequence of runtime PM APIs, to undo actions during ->probe() and to put
the device into low power state.
->remove()
...
pm_runtime_put()
pm_runtime_disable()
...
Similar as in the failing ->probe() case, this sequence don't guarantee
the runtime PM status of the device to turn into RPM_SUSPENDED.
Trying to re-bind the driver thus causes the same issue as when re-trying
->probe(), in the probe deferral scenario.
Expectation 2)
Drivers that invokes the pm_runtime_irq_safe() API during ->probe(),
triggers the runtime PM core to increase the usage count for the device's
parent and permanently make it runtime resumed.
The usage count is only dropped at device removal, which also allows it to
be runtime suspended again.
A re-trying ->probe() repeats the call to pm_runtime_irq_safe() and thus
once more triggers the usage count of the device's parent to be increased.
This leads to not only an imbalance issue of the usage count of the
device's parent, but also to keep it runtime resumed permanently even if
->probe() fails.
To address these issues, let's change the policy of the driver core to
meet these expectations. More precisely, at ->probe() failures and driver
unbind, restore the initial states of runtime PM.
Although to still allow subsystem's to control PM for devices that doesn't
->probe() successfully, don't restore the initial states unless runtime PM
is disabled.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
