Clean up: this field is no longer used.
xprt_rdma_pad_optimize is also no longer used, but is left in place
because it is part of the kernel/userspace API.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
This is a buffer to be left persistently registered while a
connection is up. Connection tear-down will automatically DMA-unmap,
invalidate, and dereg the MR. A persistently registered buffer is
lower in cost to provide, and it can never be coalesced into the
RDMA segment that carries the data payload.
An RPC that provisions a Write chunk with a non-aligned length now
uses this MR rather than the tail buffer of the RPC's rq_rcv_buf.
Reviewed-By: Tom Talpey <tom@talpey.com>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
The current range of RPC task PIDs is 0..65535. That's not adequate
for distinguishing tasks across multiple rpc_clnts running high
throughput workloads.
To help relieve this situation and to reduce the bottleneck of
having a single atomic for assigning all RPC task PIDs, assign task
PIDs per rpc_clnt.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
The clearing of the XPRT_LOCKED bit has to happen after we clear
xprt->snd_task, but we don't require any extra memory barriers after
that.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
The premise of commit 6f9f17287e ("SUNRPC: Mitigate cond_resched() in
xprt_transmit()") was that cond_resched() is expensive and unnecessary
when there has been just a single send.
The point of cond_resched() is to ensure that tasks that should pre-empt
this one get a chance to do so when it is safe to do so. The code prior
to commit 6f9f17287e failed to take into account that it was keeping a
rpc_task pinned for longer than it needed to, and so rather than doing a
full revert, let's just move the cond_resched.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Jann Horn reported that SO_PEERCRED and SO_PEERGROUPS implementations
are racy, as af_unix can concurrently change sk_peer_pid and sk_peer_cred.
In order to fix this issue, this patch adds a new spinlock that needs
to be used whenever these fields are read or written.
Jann also pointed out that l2cap_sock_get_peer_pid_cb() is currently
reading sk->sk_peer_pid which makes no sense, as this field
is only possibly set by AF_UNIX sockets.
We will have to clean this in a separate patch.
This could be done by reverting b48596d1dc "Bluetooth: L2CAP: Add get_peer_pid callback"
or implementing what was truly expected.
Fixes: 109f6e39fa ("af_unix: Allow SO_PEERCRED to work across namespaces.")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Jann Horn <jannh@google.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
struct dev_addr_list is used for device addresses, unicast addresses
and multicast addresses. The first of those needs special handling
of the main address - netdev->dev_addr points directly the data
of the entry and drivers write to it freely, so we can't maintain
it in the rbtree (for now, at least, to be fixed in net-next).
Current work around sprinkles special handling of the first
address on the list throughout the code but it missed the case
where address is being added. First address will not be visible
during subsequent adds.
Syzbot found a warning where unicast addresses are modified
without holding the rtnl lock, tl;dr is that team generates
the same modification multiple times, not necessarily when
right locks are held.
In the repro we have:
macvlan -> team -> veth
macvlan adds a unicast address to the team. Team then pushes
that address down to its memebers (veths). Next something unrelated
makes team sync member addrs again, and because of the bug
the addr entries get duplicated in the veths. macvlan gets
removed, removes its addr from team which removes only one
of the duplicated addresses from veths. This removal is done
under rtnl. Next syzbot uses iptables to add a multicast addr
to team (which does not hold rtnl lock). Team syncs veth addrs,
but because veths' unicast list still has the duplicate it will
also get sync, even though this update is intended for mc addresses.
Again, uc address updates need rtnl lock, boom.
Reported-by: syzbot+7a2ab2cdc14d134de553@syzkaller.appspotmail.com
Fixes: 406f42fa0d ("net-next: When a bond have a massive amount of VLANs with IPv6 addresses, performance of changing link state, attaching a VRF, changing an IPv6 address, etc. go down dramtically.")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sequence count bridge_mcast_querier::seq is protected by
net_bridge::multicast_lock but seqcount_init() does not associate the
seqcount with the lock. This leads to a warning on PREEMPT_RT because
preemption is still enabled.
Let seqcount_init() associate the seqcount with lock that protects the
write section. Remove lockdep_assert_held_once() because lockdep already checks
whether the associated lock is held.
Fixes: 67b746f94f ("net: bridge: mcast: make sure querier port/address updates are consistent")
Reported-by: Mike Galbraith <efault@gmx.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-by: Mike Galbraith <efault@gmx.de>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Link: https://lore.kernel.org/r/20210928141049.593833-1-bigeasy@linutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Daniel Borkmann says:
====================
pull-request: bpf 2021-09-28
The following pull-request contains BPF updates for your *net* tree.
We've added 10 non-merge commits during the last 14 day(s) which contain
a total of 11 files changed, 139 insertions(+), 53 deletions(-).
The main changes are:
1) Fix MIPS JIT jump code emission for too large offsets, from Piotr Krysiuk.
2) Fix x86 JIT atomic/fetch emission when dst reg maps to rax, from Johan Almbladh.
3) Fix cgroup_sk_alloc corner case when called from interrupt, from Daniel Borkmann.
4) Fix segfault in libbpf's linker for objects without BTF, from Kumar Kartikeya Dwivedi.
5) Fix bpf_jit_charge_modmem for applications with CAP_BPF, from Lorenz Bauer.
6) Fix return value handling for struct_ops BPF programs, from Hou Tao.
7) Various fixes to BPF selftests, from Jiri Benc.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
,
unix_create1() returns NULL on error, and the callers assume that it never
fails for reasons other than out of memory. So, the callers always return
-ENOMEM when unix_create1() fails.
However, it also returns NULL when the number of af_unix sockets exceeds
twice the limit controlled by sysctl: fs.file-max. In this case, the
callers should return -ENFILE like alloc_empty_file().
This patch changes unix_create1() to return the correct error value instead
of NULL on error.
Out of curiosity, the assumption has been wrong since 1999 due to this
change introduced in 2.2.4 [0].
diff -u --recursive --new-file v2.2.3/linux/net/unix/af_unix.c linux/net/unix/af_unix.c
--- v2.2.3/linux/net/unix/af_unix.c Tue Jan 19 11:32:53 1999
+++ linux/net/unix/af_unix.c Sun Mar 21 07:22:00 1999
@@ -388,6 +413,9 @@
{
struct sock *sk;
+ if (atomic_read(&unix_nr_socks) >= 2*max_files)
+ return NULL;
+
MOD_INC_USE_COUNT;
sk = sk_alloc(PF_UNIX, GFP_KERNEL, 1);
if (!sk) {
[0]: https://cdn.kernel.org/pub/linux/kernel/v2.2/patch-2.2.4.gz
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
up->corkflag field can be read or written without any lock.
Annotate accesses to avoid possible syzbot/KCSAN reports.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* potential use-after-free in CCMP/GCMP RX processing
* potential use-after-free in TX A-MSDU processing
* revert to low data rates for no-ack as the commit
broke other things
* limit VHT MCS/NSS in radiotap injection
* drop frames with invalid addresses in IBSS mode
* check rhashtable_init() return value in mesh
* fix potentially unaligned access in mesh
* fix late beacon hrtimer handling in hwsim (syzbot)
* fix documentation for PTK0 rekeying
-----BEGIN PGP SIGNATURE-----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=hQAp
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-net-2021-09-27' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes berg says:
====================
Some fixes:
* potential use-after-free in CCMP/GCMP RX processing
* potential use-after-free in TX A-MSDU processing
* revert to low data rates for no-ack as the commit
broke other things
* limit VHT MCS/NSS in radiotap injection
* drop frames with invalid addresses in IBSS mode
* check rhashtable_init() return value in mesh
* fix potentially unaligned access in mesh
* fix late beacon hrtimer handling in hwsim (syzbot)
* fix documentation for PTK0 rekeying
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When rhashtable_init() fails, it returns -EINVAL.
However, since error return value of rhashtable_init is not checked,
it can cause use of uninitialized pointers.
So, fix unhandled errors of rhashtable_init.
Signed-off-by: MichelleJin <shjy180909@gmail.com>
Link: https://lore.kernel.org/r/20210927033457.1020967-4-shjy180909@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When PN checking is done in mac80211, for fragmentation we need
to copy the PN to the RX struct so we can later use it to do a
comparison, since commit bf30ca922a ("mac80211: check defrag
PN against current frame").
Unfortunately, in that commit I used the 'hdr' variable without
it being necessarily valid, so use-after-free could occur if it
was necessary to reallocate (parts of) the frame.
Fix this by reloading the variable after the code that results
in the reallocations, if any.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=214401.
Cc: stable@vger.kernel.org
Fixes: bf30ca922a ("mac80211: check defrag PN against current frame")
Link: https://lore.kernel.org/r/20210927115838.12b9ac6bb233.I1d066acd5408a662c3b6e828122cd314fcb28cdb@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We observed below report when playing with netlink sock:
UBSAN: shift-out-of-bounds in net/sched/sch_api.c:580:10
shift exponent 249 is too large for 32-bit type
CPU: 0 PID: 685 Comm: a.out Not tainted
Call Trace:
dump_stack_lvl+0x8d/0xcf
ubsan_epilogue+0xa/0x4e
__ubsan_handle_shift_out_of_bounds+0x161/0x182
__qdisc_calculate_pkt_len+0xf0/0x190
__dev_queue_xmit+0x2ed/0x15b0
it seems like kernel won't check the stab log value passing from
user, and will use the insane value later to calculate pkt_len.
This patch just add a check on the size/cell_log to avoid insane
calculation.
Reported-by: Abaci <abaci@linux.alibaba.com>
Signed-off-by: Michael Wang <yun.wang@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS fixes for net
1) ipset limits the max allocatable memory via kvmalloc() to MAX_INT,
from Jozsef Kadlecsik.
2) Check ip_vs_conn_tab_bits value to be in the range specified
in Kconfig, from Andrea Claudi.
3) Initialize fragment offset in ip6tables, from Jeremy Sowden.
4) Make conntrack hash chain length random, from Florian Westphal.
5) Add zone ID to conntrack and NAT hashtuple again, also from Florian.
6) Add selftests for bidirectional zone support and colliding tuples,
from Florian Westphal.
7) Unlink table before synchronize_rcu when cleaning tables with
owner, from Florian.
8) ipset limits the max allocatable memory via kvmalloc() to MAX_INT.
9) Release conntrack entries via workqueue in masquerade, from Florian.
10) Fix bogus net_init in iptables raw table definition, also from Florian.
11) Work around missing softdep in log extensions, from Florian Westphal.
12) Serialize hash resizes and cleanups with mutex, from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/pablo/nf:
netfilter: conntrack: serialize hash resizes and cleanups
netfilter: log: work around missing softdep backend module
netfilter: iptable_raw: drop bogus net_init annotation
netfilter: nf_nat_masquerade: defer conntrack walk to work queue
netfilter: nf_nat_masquerade: make async masq_inet6_event handling generic
netfilter: nf_tables: Fix oversized kvmalloc() calls
netfilter: nf_tables: unlink table before deleting it
selftests: netfilter: add zone stress test with colliding tuples
selftests: netfilter: add selftest for directional zone support
netfilter: nat: include zone id in nat table hash again
netfilter: conntrack: include zone id in tuple hash again
netfilter: conntrack: make max chain length random
netfilter: ip6_tables: zero-initialize fragment offset
ipvs: check that ip_vs_conn_tab_bits is between 8 and 20
netfilter: ipset: Fix oversized kvmalloc() calls
====================
Link: https://lore.kernel.org/r/20210924221113.348767-1-pablo@netfilter.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Multipath RTA_FLOW is embedded in nexthop. Dump it in fib_add_nexthop()
to get the length of rtnexthop correct.
Fixes: b0f6019363 ("ipv4: Refactor nexthop attributes in fib_dump_info")
Signed-off-by: Xiao Liang <shaw.leon@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
current Linux refuses to change the 'backup' bit of MPTCP endpoints, i.e.
using MPTCP_PM_CMD_SET_FLAGS, unless it finds (at least) one subflow that
matches the endpoint address. There is no reason for that, so we can just
ignore the return value of mptcp_nl_addr_backup(). In this way, endpoints
can reconfigure their 'backup' flag even if no MPTCP sockets are open (or
more generally, in case the MP_PRIO message is not sent out).
Fixes: 0f9f696a50 ("mptcp: add set_flags command in PM netlink")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mptcp_token_get_sock() may return a mptcp socket that is in
a different net namespace than the socket that received the token value.
The mptcp syncookie code path had an explicit check for this,
this moves the test into mptcp_token_get_sock() function.
Eventually token.c should be converted to pernet storage, but
such change is not suitable for net tree.
Fixes: 2c5ebd001d ("mptcp: refactor token container")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should always check if skb_header_pointer's return is NULL before
using it, otherwise it may cause null-ptr-deref, as syzbot reported:
KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007]
RIP: 0010:sctp_rcv_ootb net/sctp/input.c:705 [inline]
RIP: 0010:sctp_rcv+0x1d84/0x3220 net/sctp/input.c:196
Call Trace:
<IRQ>
sctp6_rcv+0x38/0x60 net/sctp/ipv6.c:1109
ip6_protocol_deliver_rcu+0x2e9/0x1ca0 net/ipv6/ip6_input.c:422
ip6_input_finish+0x62/0x170 net/ipv6/ip6_input.c:463
NF_HOOK include/linux/netfilter.h:307 [inline]
NF_HOOK include/linux/netfilter.h:301 [inline]
ip6_input+0x9c/0xd0 net/ipv6/ip6_input.c:472
dst_input include/net/dst.h:460 [inline]
ip6_rcv_finish net/ipv6/ip6_input.c:76 [inline]
NF_HOOK include/linux/netfilter.h:307 [inline]
NF_HOOK include/linux/netfilter.h:301 [inline]
ipv6_rcv+0x28c/0x3c0 net/ipv6/ip6_input.c:297
Fixes: 3acb50c18d ("sctp: delay as much as possible skb_linearize")
Reported-by: syzbot+581aff2ae6b860625116@syzkaller.appspotmail.com
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
syzkaller discovered memory leaks [1] that can be reduced to the
following commands:
# ip nexthop add id 1 blackhole
# devlink dev reload pci/0000:06:00.0
As part of the reload flow, mlxsw will unregister its netdevs and then
unregister from the nexthop notification chain. Before unregistering
from the notification chain, mlxsw will receive delete notifications for
nexthop objects using netdevs registered by mlxsw or their uppers. mlxsw
will not receive notifications for nexthops using netdevs that are not
dismantled as part of the reload flow. For example, the blackhole
nexthop above that internally uses the loopback netdev as its nexthop
device.
One way to fix this problem is to have listeners flush their nexthop
tables after unregistering from the notification chain. This is
error-prone as evident by this patch and also not symmetric with the
registration path where a listener receives a dump of all the existing
nexthops.
Therefore, fix this problem by replaying delete notifications for the
listener being unregistered. This is symmetric to the registration path
and also consistent with the netdev notification chain.
The above means that unregister_nexthop_notifier(), like
register_nexthop_notifier(), will have to take RTNL in order to iterate
over the existing nexthops and that any callers of the function cannot
hold RTNL. This is true for mlxsw and netdevsim, but not for the VXLAN
driver. To avoid a deadlock, change the latter to unregister its nexthop
listener without holding RTNL, making it symmetric to the registration
path.
[1]
unreferenced object 0xffff88806173d600 (size 512):
comm "syz-executor.0", pid 1290, jiffies 4295583142 (age 143.507s)
hex dump (first 32 bytes):
41 9d 1e 60 80 88 ff ff 08 d6 73 61 80 88 ff ff A..`......sa....
08 d6 73 61 80 88 ff ff 01 00 00 00 00 00 00 00 ..sa............
backtrace:
[<ffffffff81a6b576>] kmemleak_alloc_recursive include/linux/kmemleak.h:43 [inline]
[<ffffffff81a6b576>] slab_post_alloc_hook+0x96/0x490 mm/slab.h:522
[<ffffffff81a716d3>] slab_alloc_node mm/slub.c:3206 [inline]
[<ffffffff81a716d3>] slab_alloc mm/slub.c:3214 [inline]
[<ffffffff81a716d3>] kmem_cache_alloc_trace+0x163/0x370 mm/slub.c:3231
[<ffffffff82e8681a>] kmalloc include/linux/slab.h:591 [inline]
[<ffffffff82e8681a>] kzalloc include/linux/slab.h:721 [inline]
[<ffffffff82e8681a>] mlxsw_sp_nexthop_obj_group_create drivers/net/ethernet/mellanox/mlxsw/spectrum_router.c:4918 [inline]
[<ffffffff82e8681a>] mlxsw_sp_nexthop_obj_new drivers/net/ethernet/mellanox/mlxsw/spectrum_router.c:5054 [inline]
[<ffffffff82e8681a>] mlxsw_sp_nexthop_obj_event+0x59a/0x2910 drivers/net/ethernet/mellanox/mlxsw/spectrum_router.c:5239
[<ffffffff813ef67d>] notifier_call_chain+0xbd/0x210 kernel/notifier.c:83
[<ffffffff813f0662>] blocking_notifier_call_chain kernel/notifier.c:318 [inline]
[<ffffffff813f0662>] blocking_notifier_call_chain+0x72/0xa0 kernel/notifier.c:306
[<ffffffff8384b9c6>] call_nexthop_notifiers+0x156/0x310 net/ipv4/nexthop.c:244
[<ffffffff83852bd8>] insert_nexthop net/ipv4/nexthop.c:2336 [inline]
[<ffffffff83852bd8>] nexthop_add net/ipv4/nexthop.c:2644 [inline]
[<ffffffff83852bd8>] rtm_new_nexthop+0x14e8/0x4d10 net/ipv4/nexthop.c:2913
[<ffffffff833e9a78>] rtnetlink_rcv_msg+0x448/0xbf0 net/core/rtnetlink.c:5572
[<ffffffff83608703>] netlink_rcv_skb+0x173/0x480 net/netlink/af_netlink.c:2504
[<ffffffff833de032>] rtnetlink_rcv+0x22/0x30 net/core/rtnetlink.c:5590
[<ffffffff836069de>] netlink_unicast_kernel net/netlink/af_netlink.c:1314 [inline]
[<ffffffff836069de>] netlink_unicast+0x5ae/0x7f0 net/netlink/af_netlink.c:1340
[<ffffffff83607501>] netlink_sendmsg+0x8e1/0xe30 net/netlink/af_netlink.c:1929
[<ffffffff832fde84>] sock_sendmsg_nosec net/socket.c:704 [inline]
[<ffffffff832fde84>] sock_sendmsg net/socket.c:724 [inline]
[<ffffffff832fde84>] ____sys_sendmsg+0x874/0x9f0 net/socket.c:2409
[<ffffffff83304a44>] ___sys_sendmsg+0x104/0x170 net/socket.c:2463
[<ffffffff83304c01>] __sys_sendmsg+0x111/0x1f0 net/socket.c:2492
[<ffffffff83304d5d>] __do_sys_sendmsg net/socket.c:2501 [inline]
[<ffffffff83304d5d>] __se_sys_sendmsg net/socket.c:2499 [inline]
[<ffffffff83304d5d>] __x64_sys_sendmsg+0x7d/0xc0 net/socket.c:2499
Fixes: 2a014b200b ("mlxsw: spectrum_router: Add support for nexthop objects")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
WARNING: CPU: 1 PID: 9 at net/mac80211/sta_info.c:554
sta_info_insert_rcu+0x121/0x12a0
Modules linked in:
CPU: 1 PID: 9 Comm: kworker/u8:1 Not tainted 5.14.0-rc7+ #253
Workqueue: phy3 ieee80211_iface_work
RIP: 0010:sta_info_insert_rcu+0x121/0x12a0
...
Call Trace:
ieee80211_ibss_finish_sta+0xbc/0x170
ieee80211_ibss_work+0x13f/0x7d0
ieee80211_iface_work+0x37a/0x500
process_one_work+0x357/0x850
worker_thread+0x41/0x4d0
If an Ad-Hoc node receives packets with invalid source MAC address,
it hits a WARN_ON in sta_info_insert_check(), this can spam the log.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20210827144230.39944-1-yuehaibing@huawei.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In ieee80211_amsdu_aggregate() set a pointer frag_tail point to the
end of skb_shinfo(head)->frag_list, and use it to bind other skb in
the end of this function. But when execute ieee80211_amsdu_aggregate()
->ieee80211_amsdu_realloc_pad()->pskb_expand_head(), the address of
skb_shinfo(head)->frag_list will be changed. However, the
ieee80211_amsdu_aggregate() not update frag_tail after call
pskb_expand_head(). That will cause the second skb can't bind to the
head skb appropriately.So we update the address of frag_tail to fix it.
Fixes: 6e0456b545 ("mac80211: add A-MSDU tx support")
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://lore.kernel.org/r/20210830073240.12736-1-pkshih@realtek.com
[reword comment]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This reverts commit d333322361 ("mac80211: do not use low data rates for
data frames with no ack flag").
Returning false early in rate_control_send_low breaks sending broadcast
packets, since rate control will not select a rate for it.
Before re-introducing a fixed version of this patch, we should probably also
make some changes to rate control to be more conservative in selecting rates
for no-ack packets and also prevent using probing rates on them, since we won't
get any feedback.
Fixes: d333322361 ("mac80211: do not use low data rates for data frames with no ack flag")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20210906083559.9109-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The Linux device model permits both the ->shutdown and ->remove driver
methods to get called during a shutdown procedure. Example: a DSA switch
which sits on an SPI bus, and the SPI bus driver calls this on its
->shutdown method:
spi_unregister_controller
-> device_for_each_child(&ctlr->dev, NULL, __unregister);
-> spi_unregister_device(to_spi_device(dev));
-> device_del(&spi->dev);
So this is a simple pattern which can theoretically appear on any bus,
although the only other buses on which I've been able to find it are
I2C:
i2c_del_adapter
-> device_for_each_child(&adap->dev, NULL, __unregister_client);
-> i2c_unregister_device(client);
-> device_unregister(&client->dev);
The implication of this pattern is that devices on these buses can be
unregistered after having been shut down. The drivers for these devices
might choose to return early either from ->remove or ->shutdown if the
other callback has already run once, and they might choose that the
->shutdown method should only perform a subset of the teardown done by
->remove (to avoid unnecessary delays when rebooting).
So in other words, the device driver may choose on ->remove to not
do anything (therefore to not unregister an MDIO bus it has registered
on ->probe), because this ->remove is actually triggered by the
device_shutdown path, and its ->shutdown method has already run and done
the minimally required cleanup.
This used to be fine until the blamed commit, but now, the following
BUG_ON triggers:
void mdiobus_free(struct mii_bus *bus)
{
/* For compatibility with error handling in drivers. */
if (bus->state == MDIOBUS_ALLOCATED) {
kfree(bus);
return;
}
BUG_ON(bus->state != MDIOBUS_UNREGISTERED);
bus->state = MDIOBUS_RELEASED;
put_device(&bus->dev);
}
In other words, there is an attempt to free an MDIO bus which was not
unregistered. The attempt to free it comes from the devres release
callbacks of the SPI device, which are executed after the device is
unregistered.
I'm not saying that the fact that MDIO buses allocated using devres
would automatically get unregistered wasn't strange. I'm just saying
that the commit didn't care about auditing existing call paths in the
kernel, and now, the following code sequences are potentially buggy:
(a) devm_mdiobus_alloc followed by plain mdiobus_register, for a device
located on a bus that unregisters its children on shutdown. After
the blamed patch, either both the alloc and the register should use
devres, or none should.
(b) devm_mdiobus_alloc followed by plain mdiobus_register, and then no
mdiobus_unregister at all in the remove path. After the blamed
patch, nobody unregisters the MDIO bus anymore, so this is even more
buggy than the previous case which needs a specific bus
configuration to be seen, this one is an unconditional bug.
In this case, DSA falls into category (a), it tries to be helpful and
registers an MDIO bus on behalf of the switch, which might be on such a
bus. I've no idea why it does it under devres.
It does this on probe:
if (!ds->slave_mii_bus && ds->ops->phy_read)
alloc and register mdio bus
and this on remove:
if (ds->slave_mii_bus && ds->ops->phy_read)
unregister mdio bus
I _could_ imagine using devres because the condition used on remove is
different than the condition used on probe. So strictly speaking, DSA
cannot determine whether the ds->slave_mii_bus it sees on remove is the
ds->slave_mii_bus that _it_ has allocated on probe. Using devres would
have solved that problem. But nonetheless, the existing code already
proceeds to unregister the MDIO bus, even though it might be
unregistering an MDIO bus it has never registered. So I can only guess
that no driver that implements ds->ops->phy_read also allocates and
registers ds->slave_mii_bus itself.
So in that case, if unregistering is fine, freeing must be fine too.
Stop using devres and free the MDIO bus manually. This will make devres
stop attempting to free a still registered MDIO bus on ->shutdown.
Fixes: ac3a68d566 ("net: phy: don't abuse devres in devm_mdiobus_register()")
Reported-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the blamed commit, dsa_tree_teardown_switches() was split into two
smaller functions, dsa_tree_teardown_switches and dsa_tree_teardown_ports.
However, the error path of dsa_tree_setup stopped calling dsa_tree_teardown_ports.
Fixes: a57d8c217a ("net: dsa: flush switchdev workqueue before tearing down CPU/DSA ports")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The abort_work is scheduled when a connection was detected to be
out-of-sync after a link failure. The work calls smc_conn_kill(),
which calls smc_close_active_abort() and that might end up calling
smc_close_cancel_work().
smc_close_cancel_work() cancels any pending close_work and tx_work but
needs to release the sock_lock before and acquires the sock_lock again
afterwards. So when the sock_lock was NOT acquired before then it may
be held after the abort_work completes. Thats why the sock_lock is
acquired before the call to smc_conn_kill() in __smc_lgr_terminate(),
but this is missing in smc_conn_abort_work().
Fix that by acquiring the sock_lock first and release it after the
call to smc_conn_kill().
Fixes: b286a0651e ("net/smc: handle incoming CDC validation message")
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Syzbot was able to trigger the following warning [1]
No repro found by syzbot yet but I was able to trigger similar issue
by having 2 scripts running in parallel, changing conntrack hash sizes,
and:
for j in `seq 1 1000` ; do unshare -n /bin/true >/dev/null ; done
It would take more than 5 minutes for net_namespace structures
to be cleaned up.
This is because nf_ct_iterate_cleanup() has to restart everytime
a resize happened.
By adding a mutex, we can serialize hash resizes and cleanups
and also make get_next_corpse() faster by skipping over empty
buckets.
Even without resizes in the picture, this patch considerably
speeds up network namespace dismantles.
[1]
INFO: task syz-executor.0:8312 can't die for more than 144 seconds.
task:syz-executor.0 state:R running task stack:25672 pid: 8312 ppid: 6573 flags:0x00004006
Call Trace:
context_switch kernel/sched/core.c:4955 [inline]
__schedule+0x940/0x26f0 kernel/sched/core.c:6236
preempt_schedule_common+0x45/0xc0 kernel/sched/core.c:6408
preempt_schedule_thunk+0x16/0x18 arch/x86/entry/thunk_64.S:35
__local_bh_enable_ip+0x109/0x120 kernel/softirq.c:390
local_bh_enable include/linux/bottom_half.h:32 [inline]
get_next_corpse net/netfilter/nf_conntrack_core.c:2252 [inline]
nf_ct_iterate_cleanup+0x15a/0x450 net/netfilter/nf_conntrack_core.c:2275
nf_conntrack_cleanup_net_list+0x14c/0x4f0 net/netfilter/nf_conntrack_core.c:2469
ops_exit_list+0x10d/0x160 net/core/net_namespace.c:171
setup_net+0x639/0xa30 net/core/net_namespace.c:349
copy_net_ns+0x319/0x760 net/core/net_namespace.c:470
create_new_namespaces+0x3f6/0xb20 kernel/nsproxy.c:110
unshare_nsproxy_namespaces+0xc1/0x1f0 kernel/nsproxy.c:226
ksys_unshare+0x445/0x920 kernel/fork.c:3128
__do_sys_unshare kernel/fork.c:3202 [inline]
__se_sys_unshare kernel/fork.c:3200 [inline]
__x64_sys_unshare+0x2d/0x40 kernel/fork.c:3200
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
RIP: 0033:0x7f63da68e739
RSP: 002b:00007f63d7c05188 EFLAGS: 00000246 ORIG_RAX: 0000000000000110
RAX: ffffffffffffffda RBX: 00007f63da792f80 RCX: 00007f63da68e739
RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000040000000
RBP: 00007f63da6e8cc4 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 00007f63da792f80
R13: 00007fff50b75d3f R14: 00007f63d7c05300 R15: 0000000000022000
Showing all locks held in the system:
1 lock held by khungtaskd/27:
#0: ffffffff8b980020 (rcu_read_lock){....}-{1:2}, at: debug_show_all_locks+0x53/0x260 kernel/locking/lockdep.c:6446
2 locks held by kworker/u4:2/153:
#0: ffff888010c69138 ((wq_completion)events_unbound){+.+.}-{0:0}, at: arch_atomic64_set arch/x86/include/asm/atomic64_64.h:34 [inline]
#0: ffff888010c69138 ((wq_completion)events_unbound){+.+.}-{0:0}, at: arch_atomic_long_set include/linux/atomic/atomic-long.h:41 [inline]
#0: ffff888010c69138 ((wq_completion)events_unbound){+.+.}-{0:0}, at: atomic_long_set include/linux/atomic/atomic-instrumented.h:1198 [inline]
#0: ffff888010c69138 ((wq_completion)events_unbound){+.+.}-{0:0}, at: set_work_data kernel/workqueue.c:634 [inline]
#0: ffff888010c69138 ((wq_completion)events_unbound){+.+.}-{0:0}, at: set_work_pool_and_clear_pending kernel/workqueue.c:661 [inline]
#0: ffff888010c69138 ((wq_completion)events_unbound){+.+.}-{0:0}, at: process_one_work+0x896/0x1690 kernel/workqueue.c:2268
#1: ffffc9000140fdb0 ((kfence_timer).work){+.+.}-{0:0}, at: process_one_work+0x8ca/0x1690 kernel/workqueue.c:2272
1 lock held by systemd-udevd/2970:
1 lock held by in:imklog/6258:
#0: ffff88807f970ff0 (&f->f_pos_lock){+.+.}-{3:3}, at: __fdget_pos+0xe9/0x100 fs/file.c:990
3 locks held by kworker/1:6/8158:
1 lock held by syz-executor.0/8312:
2 locks held by kworker/u4:13/9320:
1 lock held by syz-executor.5/10178:
1 lock held by syz-executor.4/10217:
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
iptables/nftables has two types of log modules:
1. backend, e.g. nf_log_syslog, which implement the functionality
2. frontend, e.g. xt_LOG or nft_log, which call the functionality
provided by backend based on nf_tables or xtables rule set.
Problem is that the request_module() call to load the backed in
nf_logger_find_get() might happen with nftables transaction mutex held
in case the call path is via nf_tables/nft_compat.
This can cause deadlocks (see 'Fixes' tags for details).
The chosen solution as to let modprobe deal with this by adding 'pre: '
soft dep tag to xt_LOG (to load the syslog backend) and xt_NFLOG (to
load nflog backend).
Eric reports that this breaks on systems with older modprobe that
doesn't support softdeps.
Another, similar issue occurs when someone either insmods xt_(NF)LOG
directly or unloads the backend module (possible if no log frontend
is in use): because the frontend module is already loaded, modprobe is
not invoked again so the softdep isn't evaluated.
Add a workaround: If nf_logger_find_get() returns -ENOENT and call
is not via nft_compat, load the backend explicitly and try again.
Else, let nft_compat ask for deferred request_module via nf_tables
infra.
Softdeps are kept in-place, so with newer modprobe the dependencies
are resolved from userspace.
Fixes: cefa31a9d4 ("netfilter: nft_log: perform module load from nf_tables")
Fixes: a38b5b56d6 ("netfilter: nf_log: add module softdeps")
Reported-and-tested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This is a leftover from the times when this function was wired up via
pernet_operations. Now its called when userspace asks for the table.
With CONFIG_NET_NS=n, iptable_raw_table_init memory has been discarded
already and we get a kernel crash.
Other tables are fine, __net_init annotation was removed already.
Fixes: fdacd57c79 ("netfilter: x_tables: never register tables by default")
Reported-by: youling 257 <youling257@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The ipv4 and device notifiers are called with RTNL mutex held.
The table walk can take some time, better not block other RTNL users.
'ip a' has been reported to block for up to 20 seconds when conntrack table
has many entries and device down events are frequent (e.g., PPP).
Reported-and-tested-by: Martin Zaharinov <micron10@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
masq_inet6_event is called asynchronously from system work queue,
because the inet6 notifier is atomic and nf_iterate_cleanup can sleep.
The ipv4 and device notifiers call nf_iterate_cleanup directly.
This is legal, but these notifiers are called with RTNL mutex held.
A large conntrack table with many devices coming and going will have severe
impact on the system usability, with 'ip a' blocking for several seconds.
This change places the defer code into a helper and makes it more
generic so ipv4 and ifdown notifiers can be converted to defer the
cleanup walk as well in a follow patch.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
syzbot reports following UAF:
BUG: KASAN: use-after-free in memcmp+0x18f/0x1c0 lib/string.c:955
nla_strcmp+0xf2/0x130 lib/nlattr.c:836
nft_table_lookup.part.0+0x1a2/0x460 net/netfilter/nf_tables_api.c:570
nft_table_lookup net/netfilter/nf_tables_api.c:4064 [inline]
nf_tables_getset+0x1b3/0x860 net/netfilter/nf_tables_api.c:4064
nfnetlink_rcv_msg+0x659/0x13f0 net/netfilter/nfnetlink.c:285
netlink_rcv_skb+0x153/0x420 net/netlink/af_netlink.c:2504
Problem is that all get operations are lockless, so the commit_mutex
held by nft_rcv_nl_event() isn't enough to stop a parallel GET request
from doing read-accesses to the table object even after synchronize_rcu().
To avoid this, unlink the table first and store the table objects in
on-stack scratch space.
Fixes: 6001a930ce ("netfilter: nftables: introduce table ownership")
Reported-and-tested-by: syzbot+f31660cf279b0557160c@syzkaller.appspotmail.com
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Similar to the conntrack change, also use the zone id for the nat source
lists if the zone id is valid in both directions.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
commit deedb59039 ("netfilter: nf_conntrack: add direction support for zones")
removed the zone id from the hash value.
This has implications on hash chain lengths with overlapping tuples, which
can hit 64k entries on released kernels, before upper droplimit was added
in d7e7747ac5 ("netfilter: refuse insertion if chain has grown too large").
With that change reverted, test script coming with this series shows
linear insertion time growth:
10000 entries in 3737 ms (now 10000 total, loop 1)
10000 entries in 16994 ms (now 20000 total, loop 2)
10000 entries in 47787 ms (now 30000 total, loop 3)
10000 entries in 72731 ms (now 40000 total, loop 4)
10000 entries in 95761 ms (now 50000 total, loop 5)
10000 entries in 96809 ms (now 60000 total, loop 6)
inserted 60000 entries from packet path in 333825 ms
With d7e7747ac5 in place, the test fails.
There are three supported zone use cases:
1. Connection is in the default zone (zone 0).
This means to special config (the default).
2. Connection is in a different zone (1 to 2**16).
This means rules are in place to put packets in
the desired zone, e.g. derived from vlan id or interface.
3. Original direction is in zone X and Reply is in zone 0.
3) allows to use of the existing NAT port collision avoidance to provide
connectivity to internet/wan even when the various zones have overlapping
source networks separated via policy routing.
In case the original zone is 0 all three cases are identical.
There is no way to place original direction in zone x and reply in
zone y (with y != 0).
Zones need to be assigned manually via the iptables/nftables ruleset,
before conntrack lookup occurs (raw table in iptables) using the
"CT" target conntrack template support
(-j CT --{zone,zone-orig,zone-reply} X).
Normally zone assignment happens based on incoming interface, but could
also be derived from packet mark, vlan id and so on.
This means that when case 3 is used, the ruleset will typically not even
assign a connection tracking template to the "reply" packets, so lookup
happens in zone 0.
However, it is possible that reply packets also match a ct zone
assignment rule which sets up a template for zone X (X > 0) in original
direction only.
Therefore, after making the zone id part of the hash, we need to do a
second lookup using the reply zone id if we did not find an entry on
the first lookup.
In practice, most deployments will either not use zones at all or the
origin and reply zones are the same, no second lookup is required in
either case.
After this change, packet path insertion test passes with constant
insertion times:
10000 entries in 1064 ms (now 10000 total, loop 1)
10000 entries in 1074 ms (now 20000 total, loop 2)
10000 entries in 1066 ms (now 30000 total, loop 3)
10000 entries in 1079 ms (now 40000 total, loop 4)
10000 entries in 1081 ms (now 50000 total, loop 5)
10000 entries in 1082 ms (now 60000 total, loop 6)
inserted 60000 entries from packet path in 6452 ms
Cc: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Similar to commit 67d6d681e1
("ipv4: make exception cache less predictible"):
Use a random drop length to make it harder to detect when entries were
hashed to same bucket list.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The resilient nexthop group torture tests in fib_nexthop.sh exposed a
possible division by zero while replacing a resilient group [1]. The
division by zero occurs when the data path sees a resilient nexthop
group with zero buckets.
The tests replace a resilient nexthop group in a loop while traffic is
forwarded through it. The tests do not specify the number of buckets
while performing the replacement, resulting in the kernel allocating a
stub resilient table (i.e, 'struct nh_res_table') with zero buckets.
This table should never be visible to the data path, but the old nexthop
group (i.e., 'oldg') might still be used by the data path when the stub
table is assigned to it.
Fix this by only assigning the stub table to the old nexthop group after
making sure the group is no longer used by the data path.
Tested with fib_nexthops.sh:
Tests passed: 222
Tests failed: 0
[1]
divide error: 0000 [#1] PREEMPT SMP KASAN
CPU: 0 PID: 1850 Comm: ping Not tainted 5.14.0-custom-10271-ga86eb53057fe #1107
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.14.0-4.fc34 04/01/2014
RIP: 0010:nexthop_select_path+0x2d2/0x1a80
[...]
Call Trace:
fib_select_multipath+0x79b/0x1530
fib_select_path+0x8fb/0x1c10
ip_route_output_key_hash_rcu+0x1198/0x2da0
ip_route_output_key_hash+0x190/0x340
ip_route_output_flow+0x21/0x120
raw_sendmsg+0x91d/0x2e10
inet_sendmsg+0x9e/0xe0
__sys_sendto+0x23d/0x360
__x64_sys_sendto+0xe1/0x1b0
do_syscall_64+0x35/0x80
entry_SYSCALL_64_after_hwframe+0x44/0xae
Cc: stable@vger.kernel.org
Fixes: 283a72a559 ("nexthop: Add implementation of resilient next-hop groups")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The process will cause napi.state to contain NAPI_STATE_SCHED and
not in the poll_list, which will cause napi_disable() to get stuck.
The prefix "NAPI_STATE_" is removed in the figure below, and
NAPI_STATE_HASHED is ignored in napi.state.
CPU0 | CPU1 | napi.state
===============================================================================
napi_disable() | | SCHED | NPSVC
napi_enable() | |
{ | |
smp_mb__before_atomic(); | |
clear_bit(SCHED, &n->state); | | NPSVC
| napi_schedule_prep() | SCHED | NPSVC
| napi_poll() |
| napi_complete_done() |
| { |
| if (n->state & (NPSVC | | (1)
| _BUSY_POLL))) |
| return false; |
| ................ |
| } | SCHED | NPSVC
| |
clear_bit(NPSVC, &n->state); | | SCHED
} | |
| |
napi_schedule_prep() | | SCHED | MISSED (2)
(1) Here return direct. Because of NAPI_STATE_NPSVC exists.
(2) NAPI_STATE_SCHED exists. So not add napi.poll_list to sd->poll_list
Since NAPI_STATE_SCHED already exists and napi is not in the
sd->poll_list queue, NAPI_STATE_SCHED cannot be cleared and will always
exist.
1. This will cause this queue to no longer receive packets.
2. If you encounter napi_disable under the protection of rtnl_lock, it
will cause the entire rtnl_lock to be locked, affecting the overall
system.
This patch uses cmpxchg to implement napi_enable(), which ensures that
there will be no race due to the separation of clear two bits.
Fixes: 2d8bff1269 ("netpoll: Close race condition between poll_one_napi and napi_disable")
Signed-off-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Reviewed-by: Dust Li <dust.li@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 86f8b1c01a ("net: dsa: Do not make user port errors fatal")
decided it was fine to ignore errors on certain ports that fail to
probe, and go on with the ports that do probe fine.
Commit fb6ec87f72 ("net: dsa: Fix type was not set for devlink port")
noticed that devlink_port_type_eth_set(dlp, dp->slave); does not get
called, and devlink notices after a timeout of 3600 seconds and prints a
WARN_ON. So it went ahead to unregister the devlink port. And because
there exists an UNUSED port flavour, we actually re-register the devlink
port as UNUSED.
Commit 08156ba430 ("net: dsa: Add devlink port regions support to
DSA") added devlink port regions, which are set up by the driver and not
by DSA.
When we trigger the devlink port deregistration and reregistration as
unused, devlink now prints another WARN_ON, from here:
devlink_port_unregister:
WARN_ON(!list_empty(&devlink_port->region_list));
So the port still has regions, which makes sense, because they were set
up by the driver, and the driver doesn't know we're unregistering the
devlink port.
Somebody needs to tear them down, and optionally (actually it would be
nice, to be consistent) set them up again for the new devlink port.
But DSA's layering stays in our way quite badly here.
The options I've considered are:
1. Introduce a function in devlink to just change a port's type and
flavour. No dice, devlink keeps a lot of state, it really wants the
port to not be registered when you set its parameters, so changing
anything can only be done by destroying what we currently have and
recreating it.
2. Make DSA cache the parameters passed to dsa_devlink_port_region_create,
and the region returned, keep those in a list, then when the devlink
port unregister needs to take place, the existing devlink regions are
destroyed by DSA, and we replay the creation of new regions using the
cached parameters. Problem: mv88e6xxx keeps the region pointers in
chip->ports[port].region, and these will remain stale after DSA frees
them. There are many things DSA can do, but updating mv88e6xxx's
private pointers is not one of them.
3. Just let the driver do it (i.e. introduce a very specific method
called ds->ops->port_reinit_as_unused, which unregisters its devlink
port devlink regions, then the old devlink port, then registers the
new one, then the devlink port regions for it). While it does work,
as opposed to the others, it's pretty horrible from an API
perspective and we can do better.
4. Introduce a new pair of methods, ->port_setup and ->port_teardown,
which in the case of mv88e6xxx must register and unregister the
devlink port regions. Call these 2 methods when the port must be
reinitialized as unused.
Naturally, I went for the 4th approach.
Fixes: 08156ba430 ("net: dsa: Add devlink port regions support to DSA")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
