Commit Graph

31 Commits

Author SHA1 Message Date
Gustavo A. R. Silva
df561f6688 treewide: Use fallthrough pseudo-keyword
Replace the existing /* fall through */ comments and its variants with
the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary
fall-through markings when it is the case.

[1] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through

Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
2020-08-23 17:36:59 -05:00
Martin Sperl
5e94c3cdaa
spi: bcm2835aux: support effective_speed_hz
Setting spi_transfer->effective_speed_hz in transfer_one so that
it can get used in cs_change_delay configured with delay as a muliple
of SPI clock cycles.

Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/20200709074120.110069-3-mkl@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
2020-07-17 00:30:45 +01:00
Lukas Wunner
b9dd3f6d41
spi: bcm2835aux: Fix controller unregister order
The BCM2835aux SPI driver uses devm_spi_register_master() on bind.
As a consequence, on unbind, __device_release_driver() first invokes
bcm2835aux_spi_remove() before unregistering the SPI controller via
devres_release_all().

This order is incorrect:  bcm2835aux_spi_remove() turns off the SPI
controller, including its interrupts and clock.  The SPI controller
is thus no longer usable.

When the SPI controller is subsequently unregistered, it unbinds all
its slave devices.  If their drivers need to access the SPI bus,
e.g. to quiesce their interrupts, unbinding will fail.

As a rule, devm_spi_register_master() must not be used if the
->remove() hook performs teardown steps which shall be performed
after unbinding of slaves.

Fix by using the non-devm variant spi_register_master().  Note that the
struct spi_master as well as the driver-private data are not freed until
after bcm2835aux_spi_remove() has finished, so accessing them is safe.

Fixes: 1ea29b39f4 ("spi: bcm2835aux: add bcm2835 auxiliary spi device driver")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v4.4+
Cc: Martin Sperl <kernel@martin.sperl.org>
Link: https://lore.kernel.org/r/32f27f4d8242e4d75f9a53f7e8f1f77483b08669.1589557526.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
2020-05-20 15:16:12 +01:00
YueHaibing
d1975d0596
spi: bcm2835aux: use devm_platform_ioremap_resource() to simplify code
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.

Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190904135918.25352-6-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
2019-09-04 17:16:08 +01:00
Stephen Boyd
6b8ac10e0d
spi: Remove dev_err() usage after platform_get_irq()
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.

// <smpl>
@@
expression ret;
struct platform_device *E;
@@

ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);

if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>

While we're here, remove braces on if statements that only have one
statement (manually).

Cc: Mark Brown <broonie@kernel.org>
Cc: linux-spi@vger.kernel.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20190730181557.90391-42-swboyd@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
2019-08-02 12:15:43 +01:00
Mark Brown
4343f61103 Linux 5.2-rc4
-----BEGIN PGP SIGNATURE-----
 
 iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAlz8fAYeHHRvcnZhbGRz
 QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG1asH/3ySguxqtqL1MCBa
 4/SZ37PHeWKMerfX6ZyJdgEqK3B+PWlmuLiOMNK5h2bPLzeQQQAmHU/mfKmpXqgB
 dHwUbG9yNnyUtTfsfRqAnCA6vpuw9Yb1oIzTCVQrgJLSWD0j7scBBvmzYqguOkto
 ThwigLUq3AILr8EfR4rh+GM+5Dn9OTEFAxwil9fPHQo7QoczwZxpURhScT6Co9TB
 DqLA3fvXbBvLs/CZy/S5vKM9hKzC+p39ApFTURvFPrelUVnythAM0dPDJg3pIn5u
 g+/+gDxDFa+7ANxvxO2ng1sJPDqJMeY/xmjJYlYyLpA33B7zLNk2vDHhAP06VTtr
 XCMhQ9s=
 =cb80
 -----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
 
 iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAlz+mPkTHGJyb29uaWVA
 a2VybmVsLm9yZwAKCRAk1otyXVSH0BXUB/95xjqF6hzkrX9vO1ewx58dWoq9g5HL
 ovD61aVBgyaZT2LnUt+iVLag6tdKg6pOVAoJnpEeCbDcMJ3cDawoIXaXnWdO7Npc
 shw75MqHQCyghc5oOuSBc91d/4DKVpy0dSkhTBUmz5Vu7cBnN2imFLwrgViJT2C7
 UsRyAX6AaUV+V52lp/EAklb1SMcgYl3Yn6vA9tHKwsCpSWsCMZz/uxI/TkslnDEx
 VIH6ZUxnZEcyXaGnpKea0TOWMyG/q7gRTPS2NCrapqt1fNdx7D5X7Q4WZWKKVrdn
 6ADQ9YPLSvORTXqDU3CWqHQeJbn/0KUEjOx4xMH8JR4ePc5Xat06dkEN
 =NNyc
 -----END PGP SIGNATURE-----

Merge tag 'v5.2-rc4' into spi-5.3

Linux 5.2-rc4
2019-06-10 18:52:53 +01:00
Thomas Gleixner
c942fddf87 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 157
Based on 3 normalized pattern(s):

  this program is free software you can redistribute it and or modify
  it under the terms of the gnu general public license as published by
  the free software foundation either version 2 of the license or at
  your option any later version this program is distributed in the
  hope that it will be useful but without any warranty without even
  the implied warranty of merchantability or fitness for a particular
  purpose see the gnu general public license for more details

  this program is free software you can redistribute it and or modify
  it under the terms of the gnu general public license as published by
  the free software foundation either version 2 of the license or at
  your option any later version [author] [kishon] [vijay] [abraham]
  [i] [kishon]@[ti] [com] this program is distributed in the hope that
  it will be useful but without any warranty without even the implied
  warranty of merchantability or fitness for a particular purpose see
  the gnu general public license for more details

  this program is free software you can redistribute it and or modify
  it under the terms of the gnu general public license as published by
  the free software foundation either version 2 of the license or at
  your option any later version [author] [graeme] [gregory]
  [gg]@[slimlogic] [co] [uk] [author] [kishon] [vijay] [abraham] [i]
  [kishon]@[ti] [com] [based] [on] [twl6030]_[usb] [c] [author] [hema]
  [hk] [hemahk]@[ti] [com] this program is distributed in the hope
  that it will be useful but without any warranty without even the
  implied warranty of merchantability or fitness for a particular
  purpose see the gnu general public license for more details

extracted by the scancode license scanner the SPDX license identifier

  GPL-2.0-or-later

has been chosen to replace the boilerplate/reference in 1105 file(s).

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.202006027@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-05-30 11:26:37 -07:00
Hoan Nguyen An
bf93b95126
spi: bcm2835aux: Remove spi_alloc_master() error printing
Printing an error on memory allocation failure is unnecessary,
as the memory allocation core code already takes care of that.

Signed-off-by: Hoan Nguyen An <na-hoan@jinso.co.jp>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
2019-05-13 13:13:47 +01:00
YueHaibing
9b186e9a65
spi: bcm2835aux: Fix build error without CONFIG_DEBUG_FS
When building CONFIG_DEBUG_FS is not set
gcc warn this:

drivers/spi/spi-bcm2835aux.c: In function bcm2835aux_spi_probe:
drivers/spi/spi-bcm2835aux.c:591:2: error: too many arguments to function bcm2835aux_debugfs_create
  bcm2835aux_debugfs_create(bs, dev_name(&pdev->dev));
  ^~~~~~~~~~~~~~~~~~~~~~~~~
drivers/spi/spi-bcm2835aux.c:145:13: note: declared here
 static void bcm2835aux_debugfs_create(struct bcm2835aux_spi *bs)

Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 8048d151eb ("spi: bcm2835aux: add driver stats to debugfs")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
2019-04-08 14:06:14 +07:00
kbuild test robot
1a8fa5166e
spi: bcm2835aux: polling_limit_us can be static
Fixes: 5fd917afc4 ("spi: bcm2835aux: make the polling duration limits configurable")
Signed-off-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
2019-04-04 13:00:20 +07:00
Martin Sperl
8048d151eb
spi: bcm2835aux: add driver stats to debugfs
To estimate efficiency add statistics on transfer types
(polling and interrupt) used to debugfs.

Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
2019-04-03 11:32:28 +07:00
Martin Sperl
5fd917afc4
spi: bcm2835aux: make the polling duration limits configurable
Under some circumstances the default 30 us polling limit is not optimal
and may lead to long delays because we are waiting on an interrupt.
with this patch we have the possibility to influence this policy.

So make this limit (in us) configurable via a module parameters
(but also modifyable via /sys/modules/...)

Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
2019-04-03 11:32:17 +07:00
Martin Sperl
ccd978b708
spi: bcm2835aux: setup gpio-cs to output and correct level during setup
Setup gpio-cs to the correct levels during setup and also make the
gpio definitely an output GPIO.

This is transparently fixing some badly configured DTs in the process
where cs-gpio is set but the gpios are still configured with native cs.

It also makes 100% sure that the initial CS levels are as expected -
especially on systems with devices on a bus with mixed CS_HIGH/CS_LOW
settings.

Fixes: 1ea29b39f4 ("spi: bcm2835aux: add bcm2835 auxiliary spi device...")
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
2019-04-03 11:32:13 +07:00
Martin Sperl
519f2c22a6
spi: bcm2835aux: warn in dmesg that native cs is not really supported
From personal bad experience (even as the author of the original driver)
it shows that native-cs is "somewhat" supported by the spi bus driver
when using a buggy device tree.

So make sure that the driver is warning in dmesg about this fact
that we are running in a not supported mode that may have surprizing
limitations.

Fixes: 1ea29b39f4 ("spi: bcm2835aux: add bcm2835 auxiliary spi device...")
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
2019-04-03 11:31:51 +07:00
Martin Sperl
509c583620
spi: bcm2835aux: fix driver to not allow 65535 (=-1) cs-gpios
The original driver by default defines num_chipselects as -1.
This actually allicates an array of 65535 entries in
of_spi_register_master.

There is a side-effect for buggy device trees that (contrary to
dt-binding documentation) have no cs-gpio defined.

This mode was never supported by the driver due to limitations
of native cs and additional code complexity and is explicitly
not stated to be implemented.

To keep backwards compatibility with such buggy DTs we limit
the number of chip_selects to 1, as for all practical purposes
it is only ever realistic to use a single chip select in
native cs mode without negative side-effects.

Fixes: 1ea29b39f4 ("spi: bcm2835aux: add bcm2835 auxiliary spi device...")
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
2019-04-03 11:31:47 +07:00
Martin Sperl
08a8549509
spi: bcm2835aux: remove dead code
Remove dead code that never can get reached, as we limit count to
a max of 3.

Suggested-by: Hubert Denkmair <h.denkmair@intence.de>
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
2019-04-03 11:31:18 +07:00
Martin Sperl
73b114ee7d
spi: bcm2835aux: fix corruptions for longer spi transfers
On long running tests with a mcp2517fd can controller it showed that
on rare occations the data read shows corruptions for longer spi transfers.

Example of a 22 byte transfer:

expected (as captured on logic analyzer):
FF FF 78 00 00 00 08 06 00 00 91 20 77 56 84 85 86 87 88 89 8a 8b

read by the driver:
FF FF 78 00 00 00 08 06 00 00 91 20 77 56 84 88 89 8a 00 00 8b 9b

To fix this use BCM2835_AUX_SPI_STAT_RX_LVL to determine when we may
read data from the fifo reliably without any corruption.

Surprisingly the only values ever empirically read in
BCM2835_AUX_SPI_STAT_RX_LVL are 0x00, 0x10, 0x20 and 0x30.
So whenever the mask is not 0 we can read from the fifo in a safe manner.

The patch has now been tested intensively and we are no longer
able to reproduce the "RX" issue any longer.

Fixes: 1ea29b39f4 ("spi: bcm2835aux: add bcm2835 auxiliary spi device...")
Reported-by: Hubert Denkmair <h.denkmair@intence.de>
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
2019-04-03 11:31:11 +07:00
Martin Sperl
c7de8500fd
spi: bcm2835aux: remove dangerous uncontrolled read of fifo
This read of the fifo is a potential candidate for a race condition
as the spi transfer is not necessarily finished and so can lead to
an early read of the fifo that still misses data.

So it has been removed.

Fixes: 1ea29b39f4 ("spi: bcm2835aux: add bcm2835 auxiliary spi device...")
Suggested-by: Hubert Denkmair <h.denkmair@intence.de>
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
2019-04-03 11:31:06 +07:00
Martin Sperl
7188a6f0ee
spi: bcm2835aux: unifying code between polling and interrupt driven code
Sharing more code between polling and interrupt-driven mode.

Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
2019-04-03 11:31:01 +07:00
YueHaibing
bfc7af6d6d
spi: bcm2835aux: remove unneeded NULL check of devm_clk_get
Fix a static code checker warning:
drivers/spi/spi-bcm2835aux.c:460
 bcm2835aux_spi_probe() warn: passing zero to 'PTR_ERR'

In case of error, the function devm_clk_get() returns ERR_PTR()
and not returns NULL.

Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
2019-01-23 10:31:21 +00:00
Stefan Wahren
22bf6cd2ca
spi: bcm2835: make license text and module license match
The license text is specifying GPL v2 or later but the MODULE_LICENSE
is set to GPL v2 which means GNU Public License v2 only. So choose the
license text as the correct one.

Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Florian Kauer <florian.kauer@koalo.de>
Acked-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
2018-11-14 14:18:18 -08:00
Rob Herring
bc519d9574
spi: bcm2835aux: ensure interrupts are enabled for shared handler
The BCM2835 AUX SPI has a shared interrupt line (with AUX UART).
Downstream fixes this with an AUX irqchip to demux the IRQ sources and a
DT change which breaks compatibility with older kernels. The AUX irqchip
was already rejected for upstream[1] and the DT change would break
working systems if the DTB is updated to a newer one. The latter issue
was brought to my attention by Alex Graf.

The root cause however is a bug in the shared handler. Shared handlers
must check that interrupts are actually enabled before servicing the
interrupt. Add a check that the TXEMPTY or IDLE interrupts are enabled.

[1] https://patchwork.kernel.org/patch/9781221/

Cc: Alexander Graf <agraf@suse.de>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Eric Anholt <eric@anholt.net>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: linux-spi@vger.kernel.org
Cc: linux-rpi-kernel@lists.infradead.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
2018-05-04 08:09:02 +09:00
Trent Piepho
d704afffe6
spi: bcm2835aux: Avoid 64-bit arithmetic in xfer len calc
We want to check for xfers that are over 30 microseconds.  Rather than
find how many µs a xfer will take, instead find how many bytes can be
transferred in 30 µs.  The latter must be less than 32 bits (since our
clock speed is limited to 32 bits), while the former involves 64 bit
quantities and more arithmetic operations.

Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
2018-02-14 16:04:58 +00:00
Mark Brown
6beb9fecbd Merge remote-tracking branches 'spi/topic/acpi', 'spi/topic/axi-engine', 'spi/topic/bcm2835' and 'spi/topic/bcm2835aux' into spi-next 2016-03-11 14:28:25 +07:00
Stephan Olbrich
e9dd4edcc9 spi: bcm2835aux: fix CPOL/CPHA setting
The auxiliary spi supports only CPHA=0 modes as the first bit is
always output to the pin before the first clock cycle. In CPHA=1
modes the first clock edge outputs the second bit hence the slave
can never read the first bit.

Also the CPHA registers switch between clocking data in/out on
rising/falling edge hence depend on the CPOL setting.

Signed-off-by: Stephan Olbrich <stephanolbrich@gmx.de>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
2016-02-15 20:45:47 +00:00
Stephan Olbrich
b4e2adef62 spi: bcm2835aux: set up spi-mode before asserting cs-gpio
When using reverse polarity for clock (spi-cpol) on a device
the clock line gets altered after chip-select has been asserted
resulting in an additional clock beat, which confuses hardware.

This happens due to the fact, the the hardware was initialized
and reset at the begin and end of each transfer which results
in default state for all lines except chip-select which is
handled by the spi-subsystem as gpio-cs is used.

To avoid this situation this patch moves the setup of polarity
(spi-cpol and spi-cpha) outside of the chip-select into
prepare_message, which is run prior to asserting chip-select.

Signed-off-by: Stephan Olbrich <stephanolbrich@gmx.de>
Reviewed-by: Martin Sperl <kernel@martin.sperl.org>
Tested-by: Martin Sperl <kernel@martin.sperl.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
2016-02-15 20:45:19 +00:00
Stephan Olbrich
f29ab1845f spi: bcm2835aux: disable tx fifo empty irq
The tx empty irq can be disabled when all data was copied.
This prevents unnecessary interrupts while the last bytes are sent.

Signed-off-by: Stephan Olbrich <stephanolbrich@gmx.de>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
2016-02-10 19:14:57 +00:00
Stephan Olbrich
fe0e2304f5 spi: bcm2835aux: fix bitmask defines
The bitmasks for txempty and idle interrupts were interchanged.

Signed-off-by: Stephan Olbrich <stephanolbrich@gmx.de>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
2016-02-10 08:02:27 +00:00
Martin Sperl
07bce09e11 spi: bcm2835aux: change initialization order and switch to platform_get_irq
Change the initialization order of the HW so that the interrupt
is only requested after the HW is initialized

Also the use of irq_of_parse_and_map is replaced by platform_get_irq.

Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
2015-10-16 15:35:33 +01:00
Martin Sperl
72aac02b37 spi: bcm2835aux: fixed bad data on longer transfers
There are strange issues with the auxiliary spi device that result
in "lost" data in the RX path if the fifo is filled by too much
(even though the status register is checked if new data can get filled
in).

This has been observed primarily for the interrupt case.
Polling works fine, probably because the RX fifo is pulled immediately
when in the tight polling loop.

For that reason we have to limit the pending bytes to less than 15
when filling the fifo in interrupt mode.

There also was an issue returning the "wrong" last 1/2 bytes
of a transfer when the transfer is not a multiple of 3 bytes.
(this impacted polling and interrupt modes)

Also fixed an overflow in the estimation of the transfer time used
to decide if we run in interrupt or polling mode (found with the
spi-bcm2835.c driver originally).

Reported-by: Georgii Staroselskii <georgii.staroselskii@emlid.com>
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
2015-10-16 15:35:33 +01:00
Martin Sperl
1ea29b39f4 spi: bcm2835aux: add bcm2835 auxiliary spi device driver
The bcm2835 has 2 auxiliary spi bus masters spi1 and spi2.

This implements the driver to enable these devices.

The driver does not implement native chip-selects but uses
the aribtrary GPIO-chip-selects provided by the spi-chipselect.

Note that this driver relies on the fact that
the clock is implemented by the clk-bcm2835-aux driver,
which enables/disables the HW block when requesting/releasing
the clock.

Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
2015-10-07 11:42:57 +01:00