[Why]
pflip interrupt order are mapped 1 to 1 to otg id.
e.g. if irq_src=26 corresponds to otg0 then 27->otg1, 28->otg2...
Linux DM registers pflip interrupts per number of crtcs.
In fused pipe case crtc numbers can be less than otg id.
e.g. if one pipe out of 3(otg#0-2) is fused adev->mode_info.num_crtc=2
so DM only registers irq_src 26,27.
This is a bug since if pipe#2 remains unfused DM never gets
otg2 pflip interrupt (irq_src=28)
That may results in gfx failure due to pflip timeout.
[How]
Register pflip interrupts per max num of otg instead of num_crtc
Signed-off-by: Roman Li <Roman.Li@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Confirmed with hardware team, there is harvesting for gc 10.3.1.
Signed-off-by: Aaron Liu <aaron.liu@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
A number of BIOS versions have a problem with the watermarks table not
being configured properly. This manifests as a very scary looking warning
during resume from s0i3. This should be harmless in most cases and is well
understood, so decrease the assertion to a clearer warning about the problem.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Commit 7f7b4236f2 ("x86/PCI: Ignore E820 reservations for bridge windows
on newer systems") fixes the touchpad not working on laptops like
the Lenovo IdeaPad 3 15IIL05 and the Lenovo IdeaPad 5 14IIL05, as well as
fixing thunderbolt hotplug issues on the Lenovo Yoga C940.
Unfortunately it turns out that this is causing issues with suspend/resume
on Lenovo ThinkPad X1 Carbon Gen 2 laptops. So, per the no regressions
policy, rever this. Note I'm looking into another fix for the issues this
fixed.
Fixes: 7f7b4236f2 ("x86/PCI: Ignore E820 reservations for bridge windows on newer systems")
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=2029207
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The original version of the IORT PMCG definition had an oversight
wherein there was no way to describe the second register page for an
implementation using the recommended RELOC_CTRS feature. Although the
spec was fixed, and the final patches merged to ACPICA and Linux written
against the new version, it seems that some old firmware based on the
original revision has survived and turned up in the wild.
Add a check for the original PMCG definition, and avoid filling in the
second memory resource with nonsense if so. Otherwise it is likely that
something horrible will happen when the PMCG driver attempts to probe.
Reported-by: Michael Petlan <mpetlan@redhat.com>
Fixes: 24e5160493 ("ACPI/IORT: Add support for PMCG")
Cc: <stable@vger.kernel.org> # 5.2.x
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Link: https://lore.kernel.org/r/75628ae41c257fb73588f7bf1c4459160e04be2b.1643916258.git.robin.murphy@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Ensure that NFS clients cannot send file size or offset values that
can cause the NFS server to crash or to return incorrect or
surprising results. In particular, fix how the NFS server handles
values larger than OFFSET_MAX.
-----BEGIN PGP SIGNATURE-----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=64n/
-----END PGP SIGNATURE-----
Merge tag 'nfsd-5.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/cel/linux
Pull more nfsd fixes from Chuck Lever:
"Ensure that NFS clients cannot send file size or offset values that
can cause the NFS server to crash or to return incorrect or surprising
results.
In particular, fix how the NFS server handles values larger than
OFFSET_MAX"
* tag 'nfsd-5.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/cel/linux:
NFSD: Deprecate NFS_OFFSET_MAX
NFSD: Fix offset type in I/O trace points
NFSD: COMMIT operations must not return NFS?ERR_INVAL
NFSD: Clamp WRITE offsets
NFSD: Fix NFSv3 SETATTR/CREATE's handling of large file sizes
NFSD: Fix ia_size underflow
NFSD: Fix the behavior of READ near OFFSET_MAX
Pull crypto fixes from Herbert Xu:
"Fix two regressions:
- Potential boot failure due to missing cryptomgr on initramfs
- Stack overflow in octeontx2"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: api - Move cryptomgr soft dependency into algapi
crypto: octeontx2 - Avoid stack variable overflow
Commit 3ba442d533 ("fs: move binfmt_misc sysctl to its own file") did
not go unnoticed, binfmt-support stopped to work on my Debian system
since v5.17-rc2 (did not check with -rc1).
The existance of the /proc/sys/fs/binfmt_misc is a precondition for
attempting to mount the binfmt_misc fs, which in turn triggers the
autoload of the binfmt_misc module. Without it, no module is loaded and
no binfmt is available at boot.
Building as built-in or manually loading the module and mounting the fs
works fine, it's therefore only a matter of interaction with user-space.
I could try to improve the Debian systemd configuration but I can't say
anything about the other distributions.
This patch restores a working system right after boot.
Fixes: 3ba442d533 ("fs: move binfmt_misc sysctl to its own file")
Signed-off-by: Domenico Andreoli <domenico.andreoli@linux.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Luis Chamberlain <mcgrof@kernel.org>
Reviewed-by: Tong Zhang <ztong0001@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The SIDA MEMOPs must only be used for secure guests, otherwise userspace
can do unwanted memory accesses.
-----BEGIN PGP SIGNATURE-----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=PBt2
-----END PGP SIGNATURE-----
Merge tag 'kvm-s390-kernel-access' from emailed bundle
Pull s390 kvm fix from Christian Borntraeger:
"Add missing check for the MEMOP ioctl
The SIDA MEMOPs must only be used for secure guests, otherwise
userspace can do unwanted memory accesses"
* tag 'kvm-s390-kernel-access' from emailed bundle:
KVM: s390: Return error on SIDA memop on normal guest
NFS_OFFSET_MAX was introduced way back in Linux v2.3.y before there
was a kernel-wide OFFSET_MAX value. As a clean up, replace the last
few uses of it with its generic equivalent, and get rid of it.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
NFSv3 and NFSv4 use u64 offset values on the wire. Record these values
verbatim without the implicit type case to loff_t.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Since, well, forever, the Linux NFS server's nfsd_commit() function
has returned nfserr_inval when the passed-in byte range arguments
were non-sensical.
However, according to RFC 1813 section 3.3.21, NFSv3 COMMIT requests
are permitted to return only the following non-zero status codes:
NFS3ERR_IO
NFS3ERR_STALE
NFS3ERR_BADHANDLE
NFS3ERR_SERVERFAULT
NFS3ERR_INVAL is not included in that list. Likewise, NFS4ERR_INVAL
is not listed in the COMMIT row of Table 6 in RFC 8881.
RFC 7530 does permit COMMIT to return NFS4ERR_INVAL, but does not
specify when it can or should be used.
Instead of dropping or failing a COMMIT request in a byte range that
is not supported, turn it into a valid request by treating one or
both arguments as zero. Offset zero means start-of-file, count zero
means until-end-of-file, so we only ever extend the commit range.
NFS servers are always allowed to commit more and sooner than
requested.
The range check is no longer bounded by NFS_OFFSET_MAX, but rather
by the value that is returned in the maxfilesize field of the NFSv3
FSINFO procedure or the NFSv4 maxfilesize file attribute.
Note that this change results in a new pynfs failure:
CMT4 st_commit.testCommitOverflow : RUNNING
CMT4 st_commit.testCommitOverflow : FAILURE
COMMIT with offset + count overflow should return
NFS4ERR_INVAL, instead got NFS4_OK
IMO the test is not correct as written: RFC 8881 does not allow the
COMMIT operation to return NFS4ERR_INVAL.
Reported-by: Dan Aloni <dan.aloni@vastdata.com>
Cc: stable@vger.kernel.org
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Reviewed-by: Bruce Fields <bfields@fieldses.org>
Ensure that a client cannot specify a WRITE range that falls in a
byte range outside what the kernel's internal types (such as loff_t,
which is signed) can represent. The kiocb iterators, invoked in
nfsd_vfs_write(), should properly limit write operations to within
the underlying file system's s_maxbytes.
Cc: stable@vger.kernel.org
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
iattr::ia_size is a loff_t, so these NFSv3 procedures must be
careful to deal with incoming client size values that are larger
than s64_max without corrupting the value.
Silently capping the value results in storing a different value
than the client passed in which is unexpected behavior, so remove
the min_t() check in decode_sattr3().
Note that RFC 1813 permits only the WRITE procedure to return
NFS3ERR_FBIG. We believe that NFSv3 reference implementations
also return NFS3ERR_FBIG when ia_size is too large.
Cc: stable@vger.kernel.org
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
iattr::ia_size is a loff_t, which is a signed 64-bit type. NFSv3 and
NFSv4 both define file size as an unsigned 64-bit type. Thus there
is a range of valid file size values an NFS client can send that is
already larger than Linux can handle.
Currently decode_fattr4() dumps a full u64 value into ia_size. If
that value happens to be larger than S64_MAX, then ia_size
underflows. I'm about to fix up the NFSv3 behavior as well, so let's
catch the underflow in the common code path: nfsd_setattr().
Cc: stable@vger.kernel.org
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Dan Aloni reports:
> Due to commit 8cfb901528 ("NFS: Always provide aligned buffers to
> the RPC read layers") on the client, a read of 0xfff is aligned up
> to server rsize of 0x1000.
>
> As a result, in a test where the server has a file of size
> 0x7fffffffffffffff, and the client tries to read from the offset
> 0x7ffffffffffff000, the read causes loff_t overflow in the server
> and it returns an NFS code of EINVAL to the client. The client as
> a result indefinitely retries the request.
The Linux NFS client does not handle NFS?ERR_INVAL, even though all
NFS specifications permit servers to return that status code for a
READ.
Instead of NFS?ERR_INVAL, have out-of-range READ requests succeed
and return a short result. Set the EOF flag in the result to prevent
the client from retrying the READ request. This behavior appears to
be consistent with Solaris NFS servers.
Note that NFSv3 and NFSv4 use u64 offset values on the wire. These
must be converted to loff_t internally before use -- an implicit
type cast is not adequate for this purpose. Otherwise VFS checks
against sb->s_maxbytes do not work properly.
Reported-by: Dan Aloni <dan.aloni@vastdata.com>
Cc: stable@vger.kernel.org
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
AER is not backed by a real request, hence we should not incorrectly
assume that when failing to send a nvme command, it is a normal request
but rather check if this is an aer and if so complete the aer (similar
to the normal completion path).
Cc: stable@vger.kernel.org
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Add NVMe request completion trace in nvme_complete_batch_req() because
nvme:nvme_complete_req tracepoint is missing in case of request batched
completion.
Signed-off-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Xin Long says:
====================
vlan: fix a netdev refcnt leak for QinQ
This issue can be simply reproduced by:
# ip link add dummy0 type dummy
# ip link add link dummy0 name dummy0.1 type vlan id 1
# ip link add link dummy0.1 name dummy0.1.2 type vlan id 2
# rmmod 8021q
unregister_netdevice: waiting for dummy0.1 to become free. Usage count = 1
So as to fix it, adjust vlan_dev_uninit() in Patch 1/1 so that it won't
be called twice for the same device, then do the fix in vlan_dev_uninit()
in Patch 2/2.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Shuang Li reported an QinQ issue by simply doing:
# ip link add dummy0 type dummy
# ip link add link dummy0 name dummy0.1 type vlan id 1
# ip link add link dummy0.1 name dummy0.1.2 type vlan id 2
# rmmod 8021q
unregister_netdevice: waiting for dummy0.1 to become free. Usage count = 1
When rmmods 8021q, all vlan devs are deleted from their real_dev's vlan grp
and added into list_kill by unregister_vlan_dev(). dummy0.1 is unregistered
before dummy0.1.2, as it's using for_each_netdev() in __rtnl_kill_links().
When unregisters dummy0.1, dummy0.1.2 is not unregistered in the event of
NETDEV_UNREGISTER, as it's been deleted from dummy0.1's vlan grp. However,
due to dummy0.1.2 still holding dummy0.1, dummy0.1 will keep waiting in
netdev_wait_allrefs(), while dummy0.1.2 will never get unregistered and
release dummy0.1, as it delays dev_put until calling dev->priv_destructor,
vlan_dev_free().
This issue was introduced by Commit 563bcbae3b ("net: vlan: fix a UAF in
vlan_dev_real_dev()"), and this patch is to fix it by moving dev_put() into
vlan_dev_uninit(), which is called after NETDEV_UNREGISTER event but before
netdev_wait_allrefs().
Fixes: 563bcbae3b ("net: vlan: fix a UAF in vlan_dev_real_dev()")
Reported-by: Shuang Li <shuali@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to introduce vlan_dev_free_egress_priority() to
free egress priority for vlan dev, and keep vlan_dev_uninit()
static as .ndo_uninit. It makes the code more clear and safer
when adding new code in vlan_dev_uninit() in the future.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ax25_kill_by_device() will set s->ax25_dev = NULL and
call ax25_disconnect() to change states of ax25_cb and
sock, if we call ax25_bind() before ax25_kill_by_device().
However, if we call ax25_bind() again between the window of
ax25_kill_by_device() and ax25_dev_device_down(), the values
and states changed by ax25_kill_by_device() will be reassigned.
Finally, ax25_dev_device_down() will deallocate net_device.
If we dereference net_device in syscall functions such as
ax25_release(), ax25_sendmsg(), ax25_getsockopt(), ax25_getname()
and ax25_info_show(), a UAF bug will occur.
One of the possible race conditions is shown below:
(USE) | (FREE)
ax25_bind() |
| ax25_kill_by_device()
ax25_bind() |
ax25_connect() | ...
| ax25_dev_device_down()
| ...
| dev_put_track(dev, ...) //FREE
ax25_release() | ...
ax25_send_control() |
alloc_skb() //USE |
the corresponding fail log is shown below:
===============================================================
BUG: KASAN: use-after-free in ax25_send_control+0x43/0x210
...
Call Trace:
...
ax25_send_control+0x43/0x210
ax25_release+0x2db/0x3b0
__sock_release+0x6d/0x120
sock_close+0xf/0x20
__fput+0x11f/0x420
...
Allocated by task 1283:
...
__kasan_kmalloc+0x81/0xa0
alloc_netdev_mqs+0x5a/0x680
mkiss_open+0x6c/0x380
tty_ldisc_open+0x55/0x90
...
Freed by task 1969:
...
kfree+0xa3/0x2c0
device_release+0x54/0xe0
kobject_put+0xa5/0x120
tty_ldisc_kill+0x3e/0x80
...
In order to fix these UAF bugs caused by rebinding operation,
this patch adds dev_hold_track() into ax25_bind() and
corresponding dev_put_track() into ax25_kill_by_device().
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rafael reports that on a system with LX2160A and Marvell DSA switches,
if a reboot occurs while the DSA master (dpaa2-eth) is up, the following
panic can be seen:
systemd-shutdown[1]: Rebooting.
Unable to handle kernel paging request at virtual address 00a0000800000041
[00a0000800000041] address between user and kernel address ranges
Internal error: Oops: 96000004 [#1] PREEMPT SMP
CPU: 6 PID: 1 Comm: systemd-shutdow Not tainted 5.16.5-00042-g8f5585009b24 #32
pc : dsa_slave_netdevice_event+0x130/0x3e4
lr : raw_notifier_call_chain+0x50/0x6c
Call trace:
dsa_slave_netdevice_event+0x130/0x3e4
raw_notifier_call_chain+0x50/0x6c
call_netdevice_notifiers_info+0x54/0xa0
__dev_close_many+0x50/0x130
dev_close_many+0x84/0x120
unregister_netdevice_many+0x130/0x710
unregister_netdevice_queue+0x8c/0xd0
unregister_netdev+0x20/0x30
dpaa2_eth_remove+0x68/0x190
fsl_mc_driver_remove+0x20/0x5c
__device_release_driver+0x21c/0x220
device_release_driver_internal+0xac/0xb0
device_links_unbind_consumers+0xd4/0x100
__device_release_driver+0x94/0x220
device_release_driver+0x28/0x40
bus_remove_device+0x118/0x124
device_del+0x174/0x420
fsl_mc_device_remove+0x24/0x40
__fsl_mc_device_remove+0xc/0x20
device_for_each_child+0x58/0xa0
dprc_remove+0x90/0xb0
fsl_mc_driver_remove+0x20/0x5c
__device_release_driver+0x21c/0x220
device_release_driver+0x28/0x40
bus_remove_device+0x118/0x124
device_del+0x174/0x420
fsl_mc_bus_remove+0x80/0x100
fsl_mc_bus_shutdown+0xc/0x1c
platform_shutdown+0x20/0x30
device_shutdown+0x154/0x330
__do_sys_reboot+0x1cc/0x250
__arm64_sys_reboot+0x20/0x30
invoke_syscall.constprop.0+0x4c/0xe0
do_el0_svc+0x4c/0x150
el0_svc+0x24/0xb0
el0t_64_sync_handler+0xa8/0xb0
el0t_64_sync+0x178/0x17c
It can be seen from the stack trace that the problem is that the
deregistration of the master causes a dev_close(), which gets notified
as NETDEV_GOING_DOWN to dsa_slave_netdevice_event().
But dsa_switch_shutdown() has already run, and this has unregistered the
DSA slave interfaces, and yet, the NETDEV_GOING_DOWN handler attempts to
call dev_close_many() on those slave interfaces, leading to the problem.
The previous attempt to avoid the NETDEV_GOING_DOWN on the master after
dsa_switch_shutdown() was called seems improper. Unregistering the slave
interfaces is unnecessary and unhelpful. Instead, after the slaves have
stopped being uppers of the DSA master, we can now reset to NULL the
master->dsa_ptr pointer, which will make DSA start ignoring all future
notifier events on the master.
Fixes: 0650bf52b3 ("net: dsa: be compatible with masters which unregister on shutdown")
Reported-by: Rafael Richter <rafael.richter@gin.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Originally we proposed a new hdmi-5v-supply regulator reference
for CI20 device tree but that was superseded by a better idea to use
the already defined "ddc-en-gpios" property of the "hdmi-connector".
Since "MIPS: DTS: CI20: Add DT nodes for HDMI setup" has already
been applied to v5.17-rc1, we add this on top.
Fixes: ae1b8d2c2d ("MIPS: DTS: CI20: Add DT nodes for HDMI setup")
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Hardware interrupts are enabled during the pci probe, however,
they are not disabled during pci removal.
Disable all hardware interrupts during pci removal to avoid any
issues.
Fixes: e753774047 ("amd-xgbe: Update PCI support to use new IRQ functions")
Suggested-by: Selwin Sebastian <Selwin.Sebastian@amd.com>
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It would be easy to craft a message containing an illegal binding table
update operation. This is handled correctly by the code, but the
corresponding warning printout is not rate limited as is should be.
We fix this now.
Fixes: b97bf3fd8f ("[TIPC] Initial merge")
Signed-off-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix loading of the driver when built as a module.
Fixes: f160e99462 ("net: phy: Add mdio-aspeed")
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEBsvAIBsPu6mG7thcrX5LkNig010FAmIDdE4THG1rbEBwZW5n
dXRyb25peC5kZQAKCRCtfkuQ2KDTXdbzB/9aYlSVCqS1tKOS57MmXBam1OrD5M6Y
R0PuMISj8zUvwKp/nLfTGG6MyPtlxLh5qK5Wu9Eq38jfKlHh64XhFbmZmVwc34ji
JzZO6znObncaWsDAUSIdv6uDB7OIuGQ94xgUXBvTkXhXnBn9P8kEWPKV6F1jSzGS
fpE3WVlRLq5DT322B51O/QXn4ET9bNacEIX9Y+teU8YkTqRowokkCwTgGt7PHo7M
M2f4ojHGUaABzkpyhK7eUOmGcmZYdQF84MrQhkQ+CF1NRzBnulH6NIJr5/PRCmy0
PWVDfnxBgOjNWSIMwQ9Mwg70GZBEoKlcByYLbU0tkA27CN/1Nwio8RkY
=21SZ
-----END PGP SIGNATURE-----
Merge tag 'linux-can-fixes-for-5.17-20220209' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2022-02-09
this is a pull request of 2 patches for net/master.
Oliver Hartkopp contributes 2 fixes for the CAN ISOTP protocol.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The ax25_disconnect() in ax25_kill_by_device() is not
protected by any locks, thus there is a race condition
between ax25_disconnect() and ax25_destroy_socket().
when ax25->sk is assigned as NULL by ax25_destroy_socket(),
a NULL pointer dereference bug will occur if site (1) or (2)
dereferences ax25->sk.
ax25_kill_by_device() | ax25_release()
ax25_disconnect() | ax25_destroy_socket()
... |
if(ax25->sk != NULL) | ...
... | ax25->sk = NULL;
bh_lock_sock(ax25->sk); //(1) | ...
... |
bh_unlock_sock(ax25->sk); //(2)|
This patch moves ax25_disconnect() into lock_sock(), which can
synchronize with ax25_destroy_socket() in ax25_release().
Fail log:
===============================================================
BUG: kernel NULL pointer dereference, address: 0000000000000088
...
RIP: 0010:_raw_spin_lock+0x7e/0xd0
...
Call Trace:
ax25_disconnect+0xf6/0x220
ax25_device_event+0x187/0x250
raw_notifier_call_chain+0x5e/0x70
dev_close_many+0x17d/0x230
rollback_registered_many+0x1f1/0x950
unregister_netdevice_queue+0x133/0x200
unregister_netdev+0x13/0x20
...
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Antoine Tenart says:
====================
net: fix issues when uncloning an skb dst+metadata
This fixes two issues when uncloning an skb dst+metadata in
tun_dst_unclone; this was initially reported by Vlad Buslov[1]. Because
of the memory leak fixed by patch 2, the issue in patch 1 never happened
in practice.
tun_dst_unclone is called from two different places, one in geneve/vxlan
to handle PMTU and one in net/openvswitch/actions.c where it is used to
retrieve tunnel information. While both Vlad and I tested the former, we
could not for the latter. I did spend quite some time trying to, but
that code path is not easy to trigger. Code inspection shows this should
be fine, the tunnel information (dst+metadata) is uncloned and the skb
it is referenced from is only consumed after all accesses to the tunnel
information are done:
do_execute_actions
output_userspace
dev_fill_metadata_dst <- dst+metadata is uncloned
ovs_dp_upcall
queue_userspace_packet
ovs_nla_put_tunnel_info <- metadata (tunnel info) is accessed
consume_skb <- dst+metadata is freed
Thanks!
Antoine
[1] https://lore.kernel.org/all/ygnhh79yluw2.fsf@nvidia.com/T/#m2f814614a4f5424cea66bbff7297f692b59b69a0
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When uncloning an skb dst and its associated metadata, a new
dst+metadata is allocated and later replaces the old one in the skb.
This is helpful to have a non-shared dst+metadata attached to a specific
skb.
The issue is the uncloned dst+metadata is initialized with a refcount of
1, which is increased to 2 before attaching it to the skb. When
tun_dst_unclone returns, the dst+metadata is only referenced from a
single place (the skb) while its refcount is 2. Its refcount will never
drop to 0 (when the skb is consumed), leading to a memory leak.
Fix this by removing the call to dst_hold in tun_dst_unclone, as the
dst+metadata refcount is already 1.
Fixes: fc4099f172 ("openvswitch: Fix egress tunnel info.")
Cc: Pravin B Shelar <pshelar@ovn.org>
Reported-by: Vlad Buslov <vladbu@nvidia.com>
Tested-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When uncloning an skb dst and its associated metadata a new dst+metadata
is allocated and the tunnel information from the old metadata is copied
over there.
The issue is the tunnel metadata has references to cached dst, which are
copied along the way. When a dst+metadata refcount drops to 0 the
metadata is freed including the cached dst entries. As they are also
referenced in the initial dst+metadata, this ends up in UaFs.
In practice the above did not happen because of another issue, the
dst+metadata was never freed because its refcount never dropped to 0
(this will be fixed in a subsequent patch).
Fix this by initializing the dst cache after copying the tunnel
information from the old metadata to also unshare the dst cache.
Fixes: d71785ffc7 ("net: add dst_cache to ovs vxlan lwtunnel")
Cc: Paolo Abeni <pabeni@redhat.com>
Reported-by: Vlad Buslov <vladbu@nvidia.com>
Tested-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We always assign the default device name as the chip_label in hog
structures which makes it impossible to assign hogs to chips. Let's
first check if a custom label was set and then copy it instead of the
default device name.
Fixes: cb8c474e79 ("gpio: sim: new testing module")
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Commit 43a08c3bda ("can: isotp: isotp_sendmsg(): fix TX buffer concurrent
access in isotp_sendmsg()") introduced a new locking scheme that may render
the userspace application in a locking state when an error is detected.
This issue shows up under high load on simultaneously running isotp channels
with identical configuration which is against the ISO specification and
therefore breaks any reasonable PDU communication anyway.
Fixes: 43a08c3bda ("can: isotp: isotp_sendmsg(): fix TX buffer concurrent access in isotp_sendmsg()")
Link: https://lore.kernel.org/all/20220209073601.25728-1-socketcan@hartkopp.net
Cc: stable@vger.kernel.org
Cc: Ziyang Xuan <william.xuanziyang@huawei.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
When receiving a CAN frame the current code logic does not consider
concurrently receiving processes which do not show up in real world
usage.
Ziyang Xuan writes:
The following syz problem is one of the scenarios. so->rx.len is
changed by isotp_rcv_ff() during isotp_rcv_cf(), so->rx.len equals
0 before alloc_skb() and equals 4096 after alloc_skb(). That will
trigger skb_over_panic() in skb_put().
=======================================================
CPU: 1 PID: 19 Comm: ksoftirqd/1 Not tainted 5.16.0-rc8-syzkaller #0
RIP: 0010:skb_panic+0x16c/0x16e net/core/skbuff.c:113
Call Trace:
<TASK>
skb_over_panic net/core/skbuff.c:118 [inline]
skb_put.cold+0x24/0x24 net/core/skbuff.c:1990
isotp_rcv_cf net/can/isotp.c:570 [inline]
isotp_rcv+0xa38/0x1e30 net/can/isotp.c:668
deliver net/can/af_can.c:574 [inline]
can_rcv_filter+0x445/0x8d0 net/can/af_can.c:635
can_receive+0x31d/0x580 net/can/af_can.c:665
can_rcv+0x120/0x1c0 net/can/af_can.c:696
__netif_receive_skb_one_core+0x114/0x180 net/core/dev.c:5465
__netif_receive_skb+0x24/0x1b0 net/core/dev.c:5579
Therefore we make sure the state changes and data structures stay
consistent at CAN frame reception time by adding a spin_lock in
isotp_rcv(). This fixes the issue reported by syzkaller but does not
affect real world operation.
Fixes: e057dd3fc2 ("can: add ISO 15765-2:2016 transport protocol")
Link: https://lore.kernel.org/linux-can/d7e69278-d741-c706-65e1-e87623d9a8e8@huawei.com/T/
Link: https://lore.kernel.org/all/20220208200026.13783-1-socketcan@hartkopp.net
Cc: stable@vger.kernel.org
Reported-by: syzbot+4c63f36709a642f801c5@syzkaller.appspotmail.com
Reported-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
When looking for a global mac index the extra NFP_TUN_PRE_TUN_IDX_BIT
that gets set if nfp_flower_is_supported_bridge is true is not taken
into account. Consequently the path that should release the ida_index
in cleanup is never triggered, causing messages like:
nfp 0000:02:00.0: nfp: Failed to offload MAC on br-ex.
nfp 0000:02:00.0: nfp: Failed to offload MAC on br-ex.
nfp 0000:02:00.0: nfp: Failed to offload MAC on br-ex.
after NFP_MAX_MAC_INDEX number of reconfigs. Ultimately this lead to
new tunnel flows not being offloaded.
Fix this by unsetting the NFP_TUN_PRE_TUN_IDX_BIT before checking if
the port is of type OTHER.
Fixes: 2e0bc7f3cb ("nfp: flower: encode mac indexes with pre-tunnel rule check")
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20220208101453.321949-1-simon.horman@corigine.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The LiteX driver uses devm io function API which
needs HAS_IOMEM enabled, so add the dependency on HAS_IOMEM.
Fixes: ee7da21ac4 ("net: Add driver for LiteX's LiteETH network interface")
Signed-off-by: Cai Huoqing <cai.huoqing@linux.dev>
Link: https://lore.kernel.org/r/20220208013308.6563-1-cai.huoqing@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If __ibmvnic_open() encounters an error such as when setting link state,
it calls release_resources() which frees the napi structures needlessly.
Instead, have __ibmvnic_open() only clean up the work it did so far (i.e.
disable napi and irqs) and leave the rest to the callers.
If caller of __ibmvnic_open() is ibmvnic_open(), it should release the
resources immediately. If the caller is do_reset() or do_hard_reset(),
they will release the resources on the next reset.
This fixes following crash that occurred when running the drmgr command
several times to add/remove a vnic interface:
[102056] ibmvnic 30000003 env3: Disabling rx_scrq[6] irq
[102056] ibmvnic 30000003 env3: Disabling rx_scrq[7] irq
[102056] ibmvnic 30000003 env3: Replenished 8 pools
Kernel attempted to read user page (10) - exploit attempt? (uid: 0)
BUG: Kernel NULL pointer dereference on read at 0x00000010
Faulting instruction address: 0xc000000000a3c840
Oops: Kernel access of bad area, sig: 11 [#1]
LE PAGE_SIZE=64K MMU=Radix SMP NR_CPUS=2048 NUMA pSeries
...
CPU: 9 PID: 102056 Comm: kworker/9:2 Kdump: loaded Not tainted 5.16.0-rc5-autotest-g6441998e2e37 #1
Workqueue: events_long __ibmvnic_reset [ibmvnic]
NIP: c000000000a3c840 LR: c0080000029b5378 CTR: c000000000a3c820
REGS: c0000000548e37e0 TRAP: 0300 Not tainted (5.16.0-rc5-autotest-g6441998e2e37)
MSR: 8000000000009033 <SF,EE,ME,IR,DR,RI,LE> CR: 28248484 XER: 00000004
CFAR: c0080000029bdd24 DAR: 0000000000000010 DSISR: 40000000 IRQMASK: 0
GPR00: c0080000029b55d0 c0000000548e3a80 c0000000028f0200 0000000000000000
...
NIP [c000000000a3c840] napi_enable+0x20/0xc0
LR [c0080000029b5378] __ibmvnic_open+0xf0/0x430 [ibmvnic]
Call Trace:
[c0000000548e3a80] [0000000000000006] 0x6 (unreliable)
[c0000000548e3ab0] [c0080000029b55d0] __ibmvnic_open+0x348/0x430 [ibmvnic]
[c0000000548e3b40] [c0080000029bcc28] __ibmvnic_reset+0x500/0xdf0 [ibmvnic]
[c0000000548e3c60] [c000000000176228] process_one_work+0x288/0x570
[c0000000548e3d00] [c000000000176588] worker_thread+0x78/0x660
[c0000000548e3da0] [c0000000001822f0] kthread+0x1c0/0x1d0
[c0000000548e3e10] [c00000000000cf64] ret_from_kernel_thread+0x5c/0x64
Instruction dump:
7d2948f8 792307e0 4e800020 60000000 3c4c01eb 384239e0 f821ffd1 39430010
38a0fff6 e92d1100 f9210028 39200000 <e9030010> f9010020 60420000 e9210020
---[ end trace 5f8033b08fd27706 ]---
Fixes: ed651a1087 ("ibmvnic: Updated reset handling")
Reported-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Reviewed-by: Dany Madden <drt@linux.ibm.com>
Link: https://lore.kernel.org/r/20220208001918.900602-1-sukadev@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Vladimir Oltean says:
====================
More DSA fixes for devres + mdiobus_{alloc,register}
The initial patch series "[net,0/2] Fix mdiobus users with devres"
https://patchwork.kernel.org/project/netdevbpf/cover/20210920214209.1733768-1-vladimir.oltean@nxp.com/
fixed some instances where DSA drivers on slow buses (SPI, I2C) trigger
a panic (changed since then to a warn) in mdiobus_free. That was due to
devres calling mdiobus_free() with no prior mdiobus_unregister(), which
again was due to commit ac3a68d566 ("net: phy: don't abuse devres in
devm_mdiobus_register()") by Bartosz Golaszewski.
Rafael Richter and Daniel Klauer report yet another variation on that
theme, but this time it applies to any DSA switch driver, not just those
on buses which have a "->shutdown() calls ->remove() which unregisters
children" sequence.
Their setup is that of an LX2160A DPAA2 SoC driving a Marvell DSA switch
(MDIO). DPAA2 Ethernet drivers probe on the "fsl-mc" bus
(drivers/bus/fsl-mc/fsl-mc-bus.c). This bus is meant to be the
kernel-side representation of the networking objects kept by the
Management Complex (MC) firmware.
The fsl-mc bus driver has this pattern:
static void fsl_mc_bus_shutdown(struct platform_device *pdev)
{
fsl_mc_bus_remove(pdev);
}
which proceeds to remove the children on the bus. Among those children,
the dpaa2-eth network driver.
When dpaa2-eth is a DSA master, this removal of the master on shutdown
trips up the device link created by dsa_master_setup(), and as such, the
Marvell switch is also removed.
From this point on, readers can revisit the description of commits
74b6d7d133 ("net: dsa: realtek: register the MDIO bus under devres")
5135e96a3d ("net: dsa: don't allocate the slave_mii_bus using devres")
since the prerequisites for the BUG_ON in mdiobus_free() have been
accomplished if there is a devres mismatch between mdiobus_alloc() and
mdiobus_register().
Most DSA drivers have this kind of mismatch, and upon my initial
assessment I had not realized the possibility described above, so I
didn't fix it. This patch series walks through all drivers and makes
them use either fully devres, or no devres.
I am aware that there are DSA drivers that are only known to be tested
with a single DSA master, so some patches are probably overkill for
them. But code is copy-pasted from so many sources without fully
understanding the differences, that I think it's better to not leave an
in-tree source of inspiration that may lead to subtle breakage if not
adapted properly.
====================
Link: https://lore.kernel.org/r/20220207161553.579933-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As explained in commits:
74b6d7d133 ("net: dsa: realtek: register the MDIO bus under devres")
5135e96a3d ("net: dsa: don't allocate the slave_mii_bus using devres")
mdiobus_free() will panic when called from devm_mdiobus_free() <-
devres_release_all() <- __device_release_driver(), and that mdiobus was
not previously unregistered.
The GSWIP switch is a platform device, so the initial set of constraints
that I thought would cause this (I2C or SPI buses which call ->remove on
->shutdown) do not apply. But there is one more which applies here.
If the DSA master itself is on a bus that calls ->remove from ->shutdown
(like dpaa2-eth, which is on the fsl-mc bus), there is a device link
between the switch and the DSA master, and device_links_unbind_consumers()
will unbind the GSWIP switch driver on shutdown.
So the same treatment must be applied to all DSA switch drivers, which
is: either use devres for both the mdiobus allocation and registration,
or don't use devres at all.
The gswip driver has the code structure in place for orderly mdiobus
removal, so just replace devm_mdiobus_alloc() with the non-devres
variant, and add manual free where necessary, to ensure that we don't
let devres free a still-registered bus.
Fixes: ac3a68d566 ("net: phy: don't abuse devres in devm_mdiobus_register()")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Nobody in this driver calls mdiobus_unregister(), which is necessary if
mdiobus_register() completes successfully. So if the devres callbacks
that free the mdiobus get invoked (this is the case when unbinding the
driver), mdiobus_free() will BUG if the mdiobus is still registered,
which it is.
My speculation is that this is due to the fact that prior to commit
ac3a68d566 ("net: phy: don't abuse devres in devm_mdiobus_register()")
from June 2020, _devm_mdiobus_free() used to call mdiobus_unregister().
But at the time that the mt7530 support was introduced in May 2021, the
API was already changed. It's therefore likely that the blamed patch was
developed on an older tree, and incorrectly adapted to net-next. This
makes the Fixes: tag correct.
Fix the problem by using the devres variant of mdiobus_register.
Fixes: ba751e28d4 ("net: dsa: mt7530: add interrupt support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As explained in commits:
74b6d7d133 ("net: dsa: realtek: register the MDIO bus under devres")
5135e96a3d ("net: dsa: don't allocate the slave_mii_bus using devres")
mdiobus_free() will panic when called from devm_mdiobus_free() <-
devres_release_all() <- __device_release_driver(), and that mdiobus was
not previously unregistered.
The Seville VSC9959 switch is a platform device, so the initial set of
constraints that I thought would cause this (I2C or SPI buses which call
->remove on ->shutdown) do not apply. But there is one more which
applies here.
If the DSA master itself is on a bus that calls ->remove from ->shutdown
(like dpaa2-eth, which is on the fsl-mc bus), there is a device link
between the switch and the DSA master, and device_links_unbind_consumers()
will unbind the seville switch driver on shutdown.
So the same treatment must be applied to all DSA switch drivers, which
is: either use devres for both the mdiobus allocation and registration,
or don't use devres at all.
The seville driver has a code structure that could accommodate both the
mdiobus_unregister and mdiobus_free calls, but it has an external
dependency upon mscc_miim_setup() from mdio-mscc-miim.c, which calls
devm_mdiobus_alloc_size() on its behalf. So rather than restructuring
that, and exporting yet one more symbol mscc_miim_teardown(), let's work
with devres and replace of_mdiobus_register with the devres variant.
When we use all-devres, we can ensure that devres doesn't free a
still-registered bus (it either runs both callbacks, or none).
Fixes: ac3a68d566 ("net: phy: don't abuse devres in devm_mdiobus_register()")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As explained in commits:
74b6d7d133 ("net: dsa: realtek: register the MDIO bus under devres")
5135e96a3d ("net: dsa: don't allocate the slave_mii_bus using devres")
mdiobus_free() will panic when called from devm_mdiobus_free() <-
devres_release_all() <- __device_release_driver(), and that mdiobus was
not previously unregistered.
The Felix VSC9959 switch is a PCI device, so the initial set of
constraints that I thought would cause this (I2C or SPI buses which call
->remove on ->shutdown) do not apply. But there is one more which
applies here.
If the DSA master itself is on a bus that calls ->remove from ->shutdown
(like dpaa2-eth, which is on the fsl-mc bus), there is a device link
between the switch and the DSA master, and device_links_unbind_consumers()
will unbind the felix switch driver on shutdown.
So the same treatment must be applied to all DSA switch drivers, which
is: either use devres for both the mdiobus allocation and registration,
or don't use devres at all.
The felix driver has the code structure in place for orderly mdiobus
removal, so just replace devm_mdiobus_alloc_size() with the non-devres
variant, and add manual free where necessary, to ensure that we don't
let devres free a still-registered bus.
Fixes: ac3a68d566 ("net: phy: don't abuse devres in devm_mdiobus_register()")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As explained in commits:
74b6d7d133 ("net: dsa: realtek: register the MDIO bus under devres")
5135e96a3d ("net: dsa: don't allocate the slave_mii_bus using devres")
mdiobus_free() will panic when called from devm_mdiobus_free() <-
devres_release_all() <- __device_release_driver(), and that mdiobus was
not previously unregistered.
The Starfighter 2 is a platform device, so the initial set of
constraints that I thought would cause this (I2C or SPI buses which call
->remove on ->shutdown) do not apply. But there is one more which
applies here.
If the DSA master itself is on a bus that calls ->remove from ->shutdown
(like dpaa2-eth, which is on the fsl-mc bus), there is a device link
between the switch and the DSA master, and device_links_unbind_consumers()
will unbind the bcm_sf2 switch driver on shutdown.
So the same treatment must be applied to all DSA switch drivers, which
is: either use devres for both the mdiobus allocation and registration,
or don't use devres at all.
The bcm_sf2 driver has the code structure in place for orderly mdiobus
removal, so just replace devm_mdiobus_alloc() with the non-devres
variant, and add manual free where necessary, to ensure that we don't
let devres free a still-registered bus.
Fixes: ac3a68d566 ("net: phy: don't abuse devres in devm_mdiobus_register()")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As explained in commits:
74b6d7d133 ("net: dsa: realtek: register the MDIO bus under devres")
5135e96a3d ("net: dsa: don't allocate the slave_mii_bus using devres")
mdiobus_free() will panic when called from devm_mdiobus_free() <-
devres_release_all() <- __device_release_driver(), and that mdiobus was
not previously unregistered.
The ar9331 is an MDIO device, so the initial set of constraints that I
thought would cause this (I2C or SPI buses which call ->remove on
->shutdown) do not apply. But there is one more which applies here.
If the DSA master itself is on a bus that calls ->remove from ->shutdown
(like dpaa2-eth, which is on the fsl-mc bus), there is a device link
between the switch and the DSA master, and device_links_unbind_consumers()
will unbind the ar9331 switch driver on shutdown.
So the same treatment must be applied to all DSA switch drivers, which
is: either use devres for both the mdiobus allocation and registration,
or don't use devres at all.
The ar9331 driver doesn't have a complex code structure for mdiobus
removal, so just replace of_mdiobus_register with the devres variant in
order to be all-devres and ensure that we don't free a still-registered
bus.
Fixes: ac3a68d566 ("net: phy: don't abuse devres in devm_mdiobus_register()")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As explained in commits:
74b6d7d133 ("net: dsa: realtek: register the MDIO bus under devres")
5135e96a3d ("net: dsa: don't allocate the slave_mii_bus using devres")
mdiobus_free() will panic when called from devm_mdiobus_free() <-
devres_release_all() <- __device_release_driver(), and that mdiobus was
not previously unregistered.
The mv88e6xxx is an MDIO device, so the initial set of constraints that
I thought would cause this (I2C or SPI buses which call ->remove on
->shutdown) do not apply. But there is one more which applies here.
If the DSA master itself is on a bus that calls ->remove from ->shutdown
(like dpaa2-eth, which is on the fsl-mc bus), there is a device link
between the switch and the DSA master, and device_links_unbind_consumers()
will unbind the Marvell switch driver on shutdown.
systemd-shutdown[1]: Powering off.
mv88e6085 0x0000000008b96000:00 sw_gl0: Link is Down
fsl-mc dpbp.9: Removing from iommu group 7
fsl-mc dpbp.8: Removing from iommu group 7
------------[ cut here ]------------
kernel BUG at drivers/net/phy/mdio_bus.c:677!
Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
Modules linked in:
CPU: 0 PID: 1 Comm: systemd-shutdow Not tainted 5.16.5-00040-gdc05f73788e5 #15
pc : mdiobus_free+0x44/0x50
lr : devm_mdiobus_free+0x10/0x20
Call trace:
mdiobus_free+0x44/0x50
devm_mdiobus_free+0x10/0x20
devres_release_all+0xa0/0x100
__device_release_driver+0x190/0x220
device_release_driver_internal+0xac/0xb0
device_links_unbind_consumers+0xd4/0x100
__device_release_driver+0x4c/0x220
device_release_driver_internal+0xac/0xb0
device_links_unbind_consumers+0xd4/0x100
__device_release_driver+0x94/0x220
device_release_driver+0x28/0x40
bus_remove_device+0x118/0x124
device_del+0x174/0x420
fsl_mc_device_remove+0x24/0x40
__fsl_mc_device_remove+0xc/0x20
device_for_each_child+0x58/0xa0
dprc_remove+0x90/0xb0
fsl_mc_driver_remove+0x20/0x5c
__device_release_driver+0x21c/0x220
device_release_driver+0x28/0x40
bus_remove_device+0x118/0x124
device_del+0x174/0x420
fsl_mc_bus_remove+0x80/0x100
fsl_mc_bus_shutdown+0xc/0x1c
platform_shutdown+0x20/0x30
device_shutdown+0x154/0x330
kernel_power_off+0x34/0x6c
__do_sys_reboot+0x15c/0x250
__arm64_sys_reboot+0x20/0x30
invoke_syscall.constprop.0+0x4c/0xe0
do_el0_svc+0x4c/0x150
el0_svc+0x24/0xb0
el0t_64_sync_handler+0xa8/0xb0
el0t_64_sync+0x178/0x17c
So the same treatment must be applied to all DSA switch drivers, which
is: either use devres for both the mdiobus allocation and registration,
or don't use devres at all.
The Marvell driver already has a good structure for mdiobus removal, so
just plug in mdiobus_free and get rid of devres.
Fixes: ac3a68d566 ("net: phy: don't abuse devres in devm_mdiobus_register()")
Reported-by: Rafael Richter <Rafael.Richter@gin.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Daniel Klauer <daniel.klauer@gin.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Today we have the code to mark connections and sessions
(and tcons) for reconnect clubbed with the code to close
the socket and abort all mids in the same function.
Sometimes, we need to mark connections and sessions
outside cifsd thread. So as a part of this change, I'm
splitting this function into two different functions and
calling them one after the other in cifs_reconnect.
Signed-off-by: Shyam Prasad N <sprasad@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
cifs_mark_tcp_ses_conns_for_reconnect helper function is now
meant to be used by any of the threads to mark a channel
(or all the channels) for reconnect.
Replace all such manual changes to tcpStatus to use this
helper function, which takes care that the right channels,
smb sessions and tcons are marked for reconnect.
Also includes one line minor change
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Shyam Prasad N <sprasad@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
