The RAS Capability Structure has some ancillary information that may be
relevant with respect to AER events, link and protcol error status
registers. Map the RAS Capability Registers in support of defining a
'struct pci_error_handlers' instance for the cxl_pci driver.
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/166974412803.1608150.7096566580400947001.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The RAS Capabilitiy Structure is a CXL Component register capability
block. Unlike the HDM Decoder Capability, it will be referenced by the
cxl_pci driver in response to PCIe AER events. Due to this it is no
longer the case that cxl_map_component_regs() can assume that it should
map all component registers. Plumb a bitmask of capability ids to map
through cxl_map_component_regs().
For symmetry cxl_probe_device_regs() is updated to populate @id in
'struct cxl_reg_map' even though cxl_map_device_regs() does not have a
need to map a subset of the device registers per caller.
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/166974412214.1608150.11487843455070795378.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
A downstream port must be connected to a component register block.
For restricted hosts the base address is determined from the RCRB. The
RCRB is provided by the host's CEDT CHBS entry. Rework CEDT parser to
get the RCRB and add code to extract the component register block from
it.
RCRB's BAR[0..1] point to the component block containing CXL subsystem
component registers. MEMBAR extraction follows the PCI base spec here,
esp. 64 bit extraction and memory range alignment (6.0, 7.5.1.2.1). The
RCRB base address is cached in the cxl_dport per-host bridge so that the
upstream port component registers can be retrieved later by an RCD
(RCIEP) associated with the host bridge.
Note: Right now the component register block is used for HDM decoder
capability only which is optional for RCDs. If unsupported by the RCD,
the HDM init will fail. It is future work to bypass it in this case.
Co-developed-by: Terry Bowman <terry.bowman@amd.com>
Signed-off-by: Terry Bowman <terry.bowman@amd.com>
Signed-off-by: Robert Richter <rrichter@amd.com>
Link: https://lore.kernel.org/r/Y4dsGZ24aJlxSfI1@rric.localdomain
[djbw: introduce devm_cxl_add_rch_dport()]
Link: https://lore.kernel.org/r/166993044524.1882361.2539922887413208807.stgit@dwillia2-xfh.jf.intel.com
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
A "DPA invalidation event" is any scenario where the contents of a DPA
(Device Physical Address) is modified in a way that is incoherent with
CPU caches, or if the HPA (Host Physical Address) to DPA association
changes due to a remapping event.
PMEM security events like Unlock and Passphrase Secure Erase already
manage caches through LIBNVDIMM, so that leaves HPA to DPA remap events
that need cache management by the CXL core. Those only happen when the
boot time CXL configuration has changed. That event occurs when
userspace attaches an endpoint decoder to a region configuration, and
that region is subsequently activated.
The implications of not invalidating caches between remap events is that
reads from the region at different points in time may return different
results due to stale cached data from the previous HPA to DPA mapping.
Without a guarantee that the region contents after cxl_region_probe()
are written before being read (a layering-violation assumption that
cxl_region_probe() can not make) the CXL subsystem needs to ensure that
reads that precede writes see consistent results.
A CONFIG_CXL_REGION_INVALIDATION_TEST option is added to support debug
and unit testing of the CXL implementation in QEMU or other environments
where cpu_cache_has_invalidate_memregion() returns false. This may prove
too restrictive for QEMU where the HDM decoders are emulated, but in
that case the CXL subsystem needs some new mechanism / indication that
the HDM decoder is emulated and not a passthrough of real hardware.
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/166993222098.1995348.16604163596374520890.stgit@dwillia2-xfh.jf.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Now that cxl_nvdimm and cxl_pmem_region objects are torn down
sychronously with the removal of either the bridge, or an endpoint, the
cxl_pmem_wq infrastructure can be jettisoned.
Tested-by: Robert Richter <rrichter@amd.com>
Link: https://lore.kernel.org/r/166993042335.1882361.17022872468068436287.stgit@dwillia2-xfh.jf.intel.com
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The three objects 'struct cxl_nvdimm_bridge', 'struct cxl_nvdimm', and
'struct cxl_pmem_region' manage CXL persistent memory resources. The
bridge represents base platform resources, the nvdimm represents one or
more endpoints, and the region is a collection of nvdimms that
contribute to an assembled address range.
Their relationship is such that a region is torn down if any component
endpoints are removed. All regions and endpoints are torn down if the
foundational bridge device goes down.
A workqueue was deployed to manage these interdependencies, but it is
difficult to reason about, and fragile. A recent attempt to take the CXL
root device lock in the cxl_mem driver was reported by lockdep as
colliding with the flush_work() in the cxl_pmem flows.
Instead of the workqueue, arrange for all pmem/nvdimm devices to be torn
down immediately and hierarchically. A similar change is made to both
the 'cxl_nvdimm' and 'cxl_pmem_region' objects. For bisect-ability both
changes are made in the same patch which unfortunately makes the patch
bigger than desired.
Arrange for cxl_memdev and cxl_region to register a cxl_nvdimm and
cxl_pmem_region as a devres release action of the bridge device.
Additionally, include a devres release action of the cxl_memdev or
cxl_region device that triggers the bridge's release action if an endpoint
exits before the bridge. I.e. this allows either unplugging the bridge,
or unplugging and endpoint to result in the same cleanup actions.
To keep the patch smaller the cleanup of the now defunct workqueue
infrastructure is saved for a follow-on patch.
Tested-by: Robert Richter <rrichter@amd.com>
Link: https://lore.kernel.org/r/166993041773.1882361.16444301376147207609.stgit@dwillia2-xfh.jf.intel.com
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Now that a cxl_nvdimm object can only experience ->remove() via an
unregistration event (because the cxl_nvdimm bind attributes are
suppressed), additional cleanups are possible.
It is already the case that the removal of a cxl_memdev object triggers
->remove() on any associated region. With that mechanism in place there
is no need for the cxl_nvdimm removal to trigger the same. Just rely on
cxl_region_detach() to tear down the whole cxl_pmem_region.
Tested-by: Robert Richter <rrichter@amd.com>
Link: https://lore.kernel.org/r/166993041215.1882361.6321535567798911286.stgit@dwillia2-xfh.jf.intel.com
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
When reviewing the CFMWS parsing code that deals with the HDM decoders,
I noticed a couple of magic numbers. This commit replaces these magic numbers
with constants defined by the CXL 3.0 specification.
v2:
- Change references to CXL 3.0 specification (David)
- CXL_DECODER_MAX_GRANULARITY_ORDER -> CXL_DECODER_MAX_ENCODED_IG (Dan)
Signed-off-by: Adam Manzanares <a.manzanares@samsung.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/20220829220249.243888-1-a.manzanares@samsung.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The function devm_cxl_iomap_block() is only used in the core
code. There are two declarations in header files of it, in
drivers/cxl/core/core.h and drivers/cxl/cxl.h. Remove its unused
declaration in drivers/cxl/cxl.h.
Fixing build error in regs.c found by kernel test robot by including
"core.h" there.
Signed-off-by: Robert Richter <rrichter@amd.com>
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Davidlohr Bueso <dave@stgolabs.net>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Link: https://lore.kernel.org/r/20221018132341.76259-2-rrichter@amd.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
When programming port decode targets, the algorithm wants to ensure that
two devices are compatible to be programmed as peers beneath a given
port. A compatible peer is a target that shares the same dport, and
where that target's interleave position also routes it to the same
dport. Compatibility is determined by the device's interleave position
being >= to distance. For example, if a given dport can only map every
Nth position then positions less than N away from the last target
programmed are incompatible.
The @distance for the host-bridge's cxl_port in a simple dual-ported
host-bridge configuration with 2 direct-attached devices is 1, i.e. An
x2 region divided by 2 dports to reach 2 region targets.
An x4 region under an x2 host-bridge would need 2 intervening switches
where the @distance at the host bridge level is 2 (x4 region divided by
2 switches to reach 4 devices).
However, the distance between peers underneath a single ported
host-bridge is always zero because there is no limit to the number of
devices that can be mapped. In other words, there are no decoders to
program in a passthrough, all descendants are mapped and distance only
starts matters for the intervening descendant ports of the passthrough
port.
Add tracking for the number of dports mapped to a port, and use that to
detect the passthrough case for calculating @distance.
Cc: <stable@vger.kernel.org>
Reported-by: Bobo WL <lmw.bobo@gmail.com>
Reported-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: http://lore.kernel.org/r/20221010172057.00001559@huawei.com
Fixes: 27b3f8d138 ("cxl/region: Program target lists")
Reviewed-by: Vishal Verma <vishal.l.verma@intel.com>
Link: https://lore.kernel.org/r/166752185440.947915.6617495912508299445.stgit@dwillia2-xfh.jf.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
When a cxl_nvdimm object goes through a ->remove() event (device
physically removed, nvdimm-bridge disabled, or nvdimm device disabled),
then any associated regions must also be disabled. As highlighted by the
cxl-create-region.sh test [1], a single device may host multiple
regions, but the driver was only tracking one region at a time. This
leads to a situation where only the last enabled region per nvdimm
device is cleaned up properly. Other regions are leaked, and this also
causes cxl_memdev reference leaks.
Fix the tracking by allowing cxl_nvdimm objects to track multiple region
associations.
Cc: <stable@vger.kernel.org>
Link: https://github.com/pmem/ndctl/blob/main/test/cxl-create-region.sh [1]
Reported-by: Vishal Verma <vishal.l.verma@intel.com>
Fixes: 04ad63f086 ("cxl/region: Introduce cxl_pmem_region objects")
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Vishal Verma <vishal.l.verma@intel.com>
Link: https://lore.kernel.org/r/166752183647.947915.2045230911503793901.stgit@dwillia2-xfh.jf.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Sphinx reported undescribed parameters in cxl_region_params struct:
./drivers/cxl/cxl.h:376: warning: Function parameter or member 'targets' not described in 'cxl_region_params'
./drivers/cxl/cxl.h:376: warning: Function parameter or member 'nr_targets' not described in 'cxl_region_params'
Describe these members.
Fixes: b9686e8c8e ("cxl/region: Enable the assignment of endpoint decoders to regions")
Signed-off-by: Bagas Sanjaya <bagasdotme@gmail.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/20220804075448.98241-3-bagasdotme@gmail.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The kernel enforces that region granularity is >= to the top-level
interleave-granularity for the given CXL window. However, when the CXL
window interleave is x1, i.e. non-interleaved at the host bridge level,
then the specified granularity does not matter. Override the window
specified granularity to the CXL minimum so that any valid region
granularity is >= to the root granularity.
Reported-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Vishal Verma <vishal.l.verma@intel.com>
Reviewed-by: Alison Schofield <alison.schofield@intel.com>
Link: https://lore.kernel.org/r/165853776917.2430596.16823264262010844458.stgit@dwillia2-xfh.jf.intel.com
[djbw: add CXL_DECODER_MIN_GRANULARITY per vishal]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The "ways" variable comes from the user. The ways_to_cxl() function
has an upper bound but it doesn't check for negatives. Make
the "ways" variable an unsigned int to fix this bug.
Fixes: 80d10a6cee ("cxl/region: Add interleave geometry attributes")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/Yueo3NV2hFCXx1iV@kili
[djbw: fixup interleave_ways_store() to only accept unsigned input]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The LIBNVDIMM subsystem is a platform agnostic representation of system
NVDIMM / persistent memory resources. To date, the CXL subsystem's
interaction with LIBNVDIMM has been to register an nvdimm-bridge device
and cxl_nvdimm objects to proxy CXL capabilities into existing LIBNVDIMM
subsystem mechanics.
With regions the approach is the same. Create a new cxl_pmem_region
object to proxy CXL region details into a LIBNVDIMM definition. With
this enabling LIBNVDIMM can partition CXL persistent memory regions with
legacy namespace labels. A follow-on patch will add CXL region label and
CXL namespace label support to persist region configurations across
driver reload / system-reset events.
Co-developed-by: Ben Widawsky <bwidawsk@kernel.org>
Signed-off-by: Ben Widawsky <bwidawsk@kernel.org>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/165784340111.1758207.3036498385188290968.stgit@dwillia2-xfh.jf.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Be careful to only disable cxl_pmem objects related to a given
cxl_nvdimm_bridge. Otherwise, offline_nvdimm_bus() reaches across CXL
domains and disables more than is expected.
Fixes: 21083f5152 ("cxl/pmem: Register 'pmem' / cxl_nvdimm devices")
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/165784339569.1758207.1557084545278004577.stgit@dwillia2-xfh.jf.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The CXL region driver is responsible for routing fully formed CXL
regions to one of libnvdimm, for persistent memory regions, device-dax
for volatile memory regions, or just act as an enumeration placeholder
if the region was setup and configuration locked by platform firmware.
In the platform-firmware-setup case the expectation is that region is
already accounted in the system memory map, i.e. already enabled as
"System RAM".
For now, just attach to CXL regions in the CXL_CONFIG_COMMIT state, and
take no further action.
Given this driver is just a small / simple router, include it in the
core rather than its own module.
Co-developed-by: Ben Widawsky <bwidawsk@kernel.org>
Signed-off-by: Ben Widawsky <bwidawsk@kernel.org>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/20220624041950.559155-18-dan.j.williams@intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
After all the soft validation of the region has completed, convey the
region configuration to hardware while being careful to commit decoders
in specification mandated order. In addition to programming the endpoint
decoder base-address, interleave ways and granularity, the switch
decoder target lists are also established.
While the kernel can enforce spec-mandated commit order, it can not
enforce spec-mandated reset order. For example, the kernel can't stop
someone from removing an endpoint device that is occupying decoderN in a
switch decoder where decoderN+1 is also committed. To reset decoderN,
decoderN+1 must be torn down first. That "tear down the world"
implementation is saved for a follow-on patch.
Callback operations are provided for the 'commit' and 'reset'
operations. While those callbacks may prove useful for CXL accelerators
(Type-2 devices with memory) the primary motivation is to enable a
simple way for cxl_test to intercept those operations.
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/165784338418.1758207.14659830845389904356.stgit@dwillia2-xfh.jf.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Once the region's interleave geometry (ways, granularity, size) is
established and all the endpoint decoder targets are assigned, the next
phase is to program all the intermediate decoders. Specifically, each
CXL switch in the path between the endpoint and its CXL host-bridge
(including the logical switch internal to the host-bridge) needs to have
its decoders programmed and the target list order assigned.
The difficulty in this implementation lies in determining which endpoint
decoder ordering combinations are valid. Consider the cxl_test case of 2
host bridges, each of those host-bridges attached to 2 switches, and
each of those switches attached to 2 endpoints for a potential 8-way
interleave. The x2 interleave at the host-bridge level requires that all
even numbered endpoint decoder positions be located on the "left" hand
side of the topology tree, and the odd numbered positions on the other.
The endpoints that are peers on the same switch need to have a position
that can be routed with a dedicated address bit per-endpoint. See
check_last_peer() for the details.
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/165784337827.1758207.132121746122685208.stgit@dwillia2-xfh.jf.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
CXL regions (interleave sets) are made up of a set of memory devices
where each device maps a portion of the interleave with one of its
decoders (see CXL 2.0 8.2.5.12 CXL HDM Decoder Capability Structure).
As endpoint decoders are identified by a provisioning tool they can be
added to a region provided the region interleave properties are set
(way, granularity, HPA) and DPA has been assigned to the decoder.
The attach event triggers several validation checks, for example:
- is the DPA sized appropriately for the region
- is the decoder reachable via the host-bridges identified by the
region's root decoder
- is the device already active in a different region position slot
- are there already regions with a higher HPA active on a given port
(per CXL 2.0 8.2.5.12.20 Committing Decoder Programming)
...and the attach event affords an opportunity to collect data and
resources relevant to later programming the target lists in switch
decoders, for example:
- allocate a decoder at each cxl_port in the decode chain
- for a given switch port, how many the region's endpoints are hosted
through the port
- how many unique targets (next hops) does a port need to map to reach
those endpoints
The act of reconciling this information and deploying it to the decoder
configuration is saved for a follow-on patch.
Co-developed-by: Ben Widawsky <bwidawsk@kernel.org>
Signed-off-by: Ben Widawsky <bwidawsk@kernel.org>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/165784337277.1758207.4108508181328528703.stgit@dwillia2-xfh.jf.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The ACPI CXL Fixed Memory Window Structure (CFMWS) defines multiple
methods to determine which host bridge provides access to a given
endpoint relative to that device's position in the interleave. The
"Interleave Arithmetic" defines either a "standard modulo" /
round-random algorithm, or "xormap" based algorithm which can be defined
as a non-linear transform. Given that there are already more options
beyond "standard modulo" and that "xormap" may turn out to be ACPI CXL
specific, provide a callback for the region provisioning code to map
endpoint positions back to expected host bridge id (cxl_dport target).
For now just support the simple modulo math case and save the xormap for
a follow-on change.
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/20220624041950.559155-14-dan.j.williams@intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The region provisioning process involves allocating DPA to a set of
endpoint decoders, and HPA plus the region geometry to a region device.
Then the decoder is assigned to the region. At this point several
validation steps can be performed to validate that the decoder is
suitable to participate in the region.
Co-developed-by: Ben Widawsky <bwidawsk@kernel.org>
Signed-off-by: Ben Widawsky <bwidawsk@kernel.org>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/165784336184.1758207.16403282029203949622.stgit@dwillia2-xfh.jf.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
After a region's interleave parameters (ways and granularity) are set,
add a way for regions to allocate HPA (host physical address space) from
the free capacity in their parent root-decoder. The allocator for this
capacity reuses the 'struct resource' based allocator used for
CONFIG_DEVICE_PRIVATE.
Once the tuple of "ways, granularity, [uuid], and size" is set the
region configuration transitions to the CXL_CONFIG_INTERLEAVE_ACTIVE
state which is a precursor to allowing endpoint decoders to be added to
a region.
Co-developed-by: Ben Widawsky <bwidawsk@kernel.org>
Signed-off-by: Ben Widawsky <bwidawsk@kernel.org>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/165784335630.1758207.420216490941955417.stgit@dwillia2-xfh.jf.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Add ABI to allow the number of devices that comprise a region to be
set as well as the interleave granularity for the region.
Signed-off-by: Ben Widawsky <bwidawsk@kernel.org>
[djbw: reword changelog]
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/20220624041950.559155-11-dan.j.williams@intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The process of provisioning a region involves triggering the creation of
a new region object, pouring in the configuration, and then binding that
configured object to the region driver to start its operation. For
persistent memory regions the CXL specification mandates that it
identified by a uuid. Add an ABI for userspace to specify a region's
uuid.
Signed-off-by: Ben Widawsky <bwidawsk@kernel.org>
[djbw: simplify locking]
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/165784334465.1758207.8224025435884752570.stgit@dwillia2-xfh.jf.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
CXL 2.0 allows for dynamic provisioning of new memory regions (system
physical address resources like "System RAM" and "Persistent Memory").
Whereas DDR and PMEM resources are conveyed statically at boot, CXL
allows for assembling and instantiating new regions from the available
capacity of CXL memory expanders in the system.
Sysfs with an "echo $region_name > $create_region_attribute" interface
is chosen as the mechanism to initiate the provisioning process. This
was chosen over ioctl() and netlink() to keep the configuration
interface entirely in a pseudo-fs interface, and it was chosen over
configfs since, aside from this one creation event, the interface is
read-mostly. I.e. configfs supports cases where an object is designed to
be provisioned each boot, like an iSCSI storage target, and CXL region
creation is mostly for PMEM regions which are created usually once
per-lifetime of a server instance. This is an improvement over nvdimm
that pre-created "seed" devices that tended to confuse users looking to
determine which devices are active and which are idle.
Recall that the major change that CXL brings over previous persistent
memory architectures is the ability to dynamically define new regions.
Compare that to drivers like 'nfit' where the region configuration is
statically defined by platform firmware.
Regions are created as a child of a root decoder that encompasses an
address space with constraints. When created through sysfs, the root
decoder is explicit. When created from an LSA's region structure a root
decoder will possibly need to be inferred by the driver.
Upon region creation through sysfs, a vacant region is created with a
unique name. Regions have a number of attributes that must be configured
before the region can be bound to the driver where HDM decoder program
is completed.
An example of creating a new region:
- Allocate a new region name:
region=$(cat /sys/bus/cxl/devices/decoder0.0/create_pmem_region)
- Create a new region by name:
while
region=$(cat /sys/bus/cxl/devices/decoder0.0/create_pmem_region)
! echo $region > /sys/bus/cxl/devices/decoder0.0/create_pmem_region
do true; done
- Region now exists in sysfs:
stat -t /sys/bus/cxl/devices/decoder0.0/$region
- Delete the region, and name:
echo $region > /sys/bus/cxl/devices/decoder0.0/delete_region
Signed-off-by: Ben Widawsky <bwidawsk@kernel.org>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/165784333909.1758207.794374602146306032.stgit@dwillia2-xfh.jf.intel.com
[djbw: simplify locking, reword changelog]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The port scanning algorithm in devm_cxl_enumerate_ports() walks up the
topology and adds cxl_port objects starting from the root down to the
endpoint. When those ports are initially created they know all their
dports, but they do not know the downstream cxl_port instance that
represents the next descendant in the topology. Rework create_endpoint()
into devm_cxl_add_endpoint() that enumerates the downstream cxl_port
topology into each port's 'struct cxl_ep' record for each endpoint it
that the port is an ancestor.
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/20220624041950.559155-7-dan.j.williams@intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Reduce the complexity and the overhead of walking the topology to
determine endpoint connectivity to root decoder interleave
configurations.
Note that cxl_detach_ep(), after it determines that the last @ep has
departed and decides to delete the port, now needs to walk the dport
array with the device_lock() held to remove entries. Previously
list_splice_init() could be used atomically delete all dport entries at
once and then perform entry tear down outside the lock. There is no
list_splice_init() equivalent for the xarray.
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/165784331647.1758207.6345820282285119339.stgit@dwillia2-xfh.jf.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
In preparation for region provisioning that needs to walk the topology
by endpoints, use an xarray to record endpoint interest in a given port.
In addition to being more space and time efficient it also reduces the
complexity of the implementation by moving locking internal to the
xarray implementation. It also allows for a single cxl_ep reference to
be recorded in multiple xarrays.
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/20220624041950.559155-2-dan.j.williams@intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
At the time that cxl_port instances are being created, cache the dport
from the parent port that points to this new child port. This will be
useful for region provisioning when walking the tree to calculate
decoder targets, and saves rewalking the dport list after the fact to
build this information.
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/20220624041950.559155-1-dan.j.williams@intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Recall that the primary role of the cxl_mem driver is to probe if the
given endpoint is connected to a CXL port topology. In that process it
walks its device ancestry to its PCI root port. If that root port is
also a CXL root port then the probe process adds cxl_port object
instances at switch in the path between to the root and the endpoint. As
those cxl_port instances are added, or if a previous enumeration
attempt already created the port, a 'struct cxl_ep' instance is
registered with that port to track the endpoints interested in that
port.
At the time the cxl_ep is registered the downstream egress path from the
port to the endpoint is known. Take the opportunity to record that
information as it will be needed for dynamic programming of decoder
targets during region provisioning.
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/165784329944.1758207.15203961796832072116.stgit@dwillia2-xfh.jf.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The CXL specification enforces that endpoint decoders are committed in
hw instance id order. In preparation for adding dynamic DPA allocation,
record the hw instance id in endpoint decoders, and enforce allocations
to occur in hw instance id order.
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/165784328827.1758207.9627538529944559954.stgit@dwillia2-xfh.jf.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Recall that the Device Physical Address (DPA) space of a CXL Memory
Expander is potentially partitioned into a volatile and persistent
portion. A decoder maps a Host Physical Address (HPA) range to a DPA
range and that translation depends on the value of all previous (lower
instance number) decoders before the current one.
In preparation for allowing dynamic provisioning of regions, decoders
need an ABI to indicate which DPA partition a decoder targets. This ABI
needs to be prepared for the possibility that some other agent committed
and locked a decoder that spans the partition boundary.
Add 'decoderX.Y/mode' to endpoint decoders that indicates which
partition 'ram' / 'pmem' the decoder targets, or 'mixed' if the decoder
currently spans the partition boundary.
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/165603881967.551046.6007594190951596439.stgit@dwillia2-xfh
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
In preparation for provisioning CXL regions, add accounting for the DPA
space consumed by existing regions / decoders. Recall, a CXL region is a
memory range comprised from one or more endpoint devices contributing a
mapping of their DPA into HPA space through a decoder.
Record the DPA ranges covered by committed decoders at initial probe of
endpoint ports relative to a per-device resource tree of the DPA type
(pmem or volatile-ram).
The cxl_dpa_rwsem semaphore is introduced to globally synchronize DPA
state across all endpoints and their decoders at once. The vast majority
of DPA operations are reads as region creation is expected to be as rare
as disk partitioning and volume creation. The device_lock() for this
synchronization is specifically avoided for concern of entangling with
sysfs attribute removal.
Co-developed-by: Ben Widawsky <bwidawsk@kernel.org>
Signed-off-by: Ben Widawsky <bwidawsk@kernel.org>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/165784327682.1758207.7914919426043855876.stgit@dwillia2-xfh.jf.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Previously the target routing specifics of switch decoders and platform
CXL window resource tracking of root decoders were factored out of
'struct cxl_decoder'. While switch decoders translate from SPA to
downstream ports, endpoint decoders translate from SPA to DPA.
This patch, 3 of 3, adds a 'struct cxl_endpoint_decoder' that tracks an
endpoint-specific Device Physical Address (DPA) resource. For now this
just defines ->dpa_res, a follow-on patch will handle requesting DPA
resource ranges from a device-DPA resource tree.
Co-developed-by: Ben Widawsky <bwidawsk@kernel.org>
Signed-off-by: Ben Widawsky <bwidawsk@kernel.org>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/165784327088.1758207.15502834501671201192.stgit@dwillia2-xfh.jf.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Previously the target routing specifics of switch decoders were factored
out of 'struct cxl_decoder' into 'struct cxl_switch_decoder'.
This patch, 2 of 3, adds a 'struct cxl_root_decoder' as a superset of a
switch decoder that also track the associated CXL window platform
resource.
Note that the reason the resource for a given root decoder needs to be
looked up after the fact (i.e. after cxl_parse_cfmws() and
add_cxl_resource()) is because add_cxl_resource() may have merged CXL
windows in order to keep them at the top of the resource tree / decode
hierarchy.
Co-developed-by: Ben Widawsky <bwidawsk@kernel.org>
Signed-off-by: Ben Widawsky <bwidawsk@kernel.org>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/165784326541.1758207.9915663937394448341.stgit@dwillia2-xfh.jf.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Currently 'struct cxl_decoder' contains the superset of attributes
needed for all decoder types. Before more type-specific attributes are
added to the common definition, reorganize 'struct cxl_decoder' into type
specific objects.
This patch, the first of three, factors out a cxl_switch_decoder type.
See the new kdoc for what a 'struct cxl_switch_decoder' represents in a
CXL topology.
Co-developed-by: Ben Widawsky <bwidawsk@kernel.org>
Signed-off-by: Ben Widawsky <bwidawsk@kernel.org>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/165784325340.1758207.5064717153608954960.stgit@dwillia2-xfh.jf.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The per-device CDAT data provides performance data that is relevant for
mapping which CXL devices can participate in which CXL ranges by QTG
(QoS Throttling Group) (per ECN: CXL 2.0 CEDT CFMWS & QTG_DSM) [1]. The
QTG association specified in the ECN is advisory. Until the
cxl_acpi driver grows support for invoking the QTG _DSM method the CDAT
data is only of interest to userspace that may need it for debug
purposes.
Search the DOE mailboxes available, query CDAT data, cache the data and
make it available via a sysfs binary attribute per endpoint at:
/sys/bus/cxl/devices/endpointX/CDAT
...similar to other ACPI-structured table data in
/sys/firmware/ACPI/tables. The CDAT is relative to 'struct cxl_port'
objects since switches in addition to endpoints can host a CDAT
instance. Switch CDAT support is not implemented.
This does not support table updates at runtime. It will always provide
whatever was there when first cached. It is also the case that table
updates are not expected outside of explicit DPA address map affecting
commands like Set Partition with the immediate flag set. Given that the
driver does not support Set Partition with the immediate flag set there
is no current need for update support.
Link: https://www.computeexpresslink.org/spec-landing [1]
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Co-developed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
[djbw: drop in-kernel parsing infra for now, and other minor fixups]
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/20220719205249.566684-7-ira.weiny@intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
While there is a need to go from a LIBNVDIMM 'struct nvdimm' to a CXL
'struct cxl_nvdimm', there is no use case to go the other direction.
Likely this is a leftover from an early version of the referenced commit
before it implemented devm for releasing the created nvdimm.
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/20220624041950.559155-19-dan.j.williams@intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Region creation has need for checking host-bridge connectivity when
adding endpoints to regions. Record, at port creation time, the
host-bridge to provide a useful shortcut from any location in the
topology to the most-significant ancestor.
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/20220624041950.559155-4-dan.j.williams@intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Interleave granularity and ways have CXL specification defined encodings.
Promote the conversion helpers to a common header, and use them to
replace other open-coded instances.
Force caller to consider the error case of the conversion similarly to
other conversion helpers like kstrto*().
Co-developed-by: Ben Widawsky <bwidawsk@kernel.org>
Signed-off-by: Ben Widawsky <bwidawsk@kernel.org>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/165603875016.551046.17236943065932132355.stgit@dwillia2-xfh
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This helper was only used to identify the object type for lockdep
purposes. Now that lockdep support is done with explicit lock classes,
this helper can be dropped.
Reviewed-by: Alison Schofield <alison.schofield@intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Adam Manzanares <a.manzanares@samsung.com>
Link: https://lore.kernel.org/r/165603874340.551046.15491766127759244728.stgit@dwillia2-xfh
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Root decoders are responsible for hosting the available host address
space for endpoints and regions to claim. The tracking of that available
capacity can be done in iomem_resource directly. As a result, root
decoders no longer need to host their own resource tree. The
current ->platform_res attribute was added prematurely.
Otherwise, ->hpa_range fills the role of conveying the current decode
range of the decoder.
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Adam Manzanares <a.manzanares@samsung.com>
Link: https://lore.kernel.org/r/165603873619.551046.791596854070136223.stgit@dwillia2-xfh
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
In preparation for growing a ->dpa_range attribute for endpoint
decoders, rename the current ->decoder_range to the more descriptive
->hpa_range.
Reviewed-by: Alison Schofield <alison.schofield@intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Adam Manzanares <a.manzanares@samsung.com>
Link: https://lore.kernel.org/r/165603872867.551046.2170426227407458814.stgit@dwillia2-xfh
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Save some characters and directly check decoder type rather than port
type. There's no need to check if the port is an endpoint port since, by
this point, cxl_endpoint_decoder_alloc() has a specified type.
Reviewed by: Adam Manzanares <a.manzanares@samsung.com>
Signed-off-by: Ben Widawsky <ben.widawsky@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Now that all CXL subsystem locking is validated with custom lock
classes, there is no need for the custom usage of the lockdep_mutex.
Cc: Alison Schofield <alison.schofield@intel.com>
Cc: Vishal Verma <vishal.l.verma@intel.com>
Cc: Ira Weiny <ira.weiny@intel.com>
Cc: Ben Widawsky <ben.widawsky@intel.com>
Cc: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Link: https://lore.kernel.org/r/165055520383.3745911.53447786039115271.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Recall that a CXL Port is any object that publishes a CXL HDM Decoder
Capability structure. That is Host Bridge and Switches that have been
enabled so far. Now, add decoder support to the 'endpoint' CXL Ports
registered by the cxl_mem driver. They mostly share the same enumeration
as Bridges and Switches, but witout a target list. The target of
endpoint decode is device-internal DPA space, not another downstream
port.
Signed-off-by: Ben Widawsky <ben.widawsky@intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
[djbw: clarify changelog, hookup enumeration in the port driver]
Link: https://lore.kernel.org/r/164386092069.765089.14895687988217608642.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
At this point the subsystem can enumerate all CXL ports (CXL.mem decode
resources in upstream switch ports and host bridges) in a system. The
last mile is connecting those ports to endpoints.
The cxl_mem driver connects an endpoint device to the platform CXL.mem
protoctol decode-topology. At ->probe() time it walks its
device-topology-ancestry and adds a CXL Port object at every Upstream
Port hop until it gets to CXL root. The CXL root object is only present
after a platform firmware driver registers platform CXL resources. For
ACPI based platform this is managed by the ACPI0017 device and the
cxl_acpi driver.
The ports are registered such that disabling a given port automatically
unregisters all descendant ports, and the chain can only be registered
after the root is established.
Given ACPI device scanning may run asynchronously compared to PCI device
scanning the root driver is tasked with rescanning the bus after the
root successfully probes.
Conversely if any ports in a chain between the root and an endpoint
becomes disconnected it subsequently triggers the endpoint to
unregister. Given lock depenedencies the endpoint unregistration happens
in a workqueue asynchronously. If userspace cares about synchronizing
delayed work after port events the /sys/bus/cxl/flush attribute is
available for that purpose.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Ben Widawsky <ben.widawsky@intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
[djbw: clarify changelog, rework hotplug support]
Link: https://lore.kernel.org/r/164398782997.903003.9725273241627693186.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
So far the platorm level CXL resources have been enumerated by the
cxl_acpi driver, and cxl_pci has gathered all the pre-requisite
information it needs to fire up a cxl_mem driver. However, the first
thing the cxl_mem driver will be tasked to do is validate that all the
PCIe Switches in its ancestry also have CXL capabilities and an CXL.mem
link established.
Provide a common mechanism for a CXL.mem endpoint driver to enumerate
all the ancestor CXL ports in the topology and validate CXL.mem
connectivity.
Multiple endpoints may end up racing to establish a shared port in the
topology. This race is resolved via taking the device-lock on a parent
CXL Port before establishing a new child. The winner of the race
establishes the port, the loser simply registers its interest in the
port via 'struct cxl_ep' place-holder reference.
At endpoint teardown the same parent port lock is taken as 'struct
cxl_ep' references are deleted. Last endpoint to drop its reference
unregisters the port.
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/164398731146.902644.1029761300481366248.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Now that dport and decoder enumeration is centralized in the port
driver, the @host argument for these helpers can be made implicit. For
the root port the host is the port's uport device (ACPI0017 for
cxl_acpi), and for all other descendant ports the devm context is the
parent of @port.
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Ben Widawsky <ben.widawsky@intel.com>
Link: https://lore.kernel.org/r/164375043390.484143.17617734732003230076.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The need for a CXL port driver and a dedicated cxl_bus_type is driven by
a need to simultaneously support 2 independent physical memory decode
domains (cache coherent CXL.mem and uncached PCI.mmio) that also
intersect at a single PCIe device node. A CXL Port is a device that
advertises a CXL Component Register block with an "HDM Decoder
Capability Structure".
>From Documentation/driver-api/cxl/memory-devices.rst:
Similar to how a RAID driver takes disk objects and assembles them into
a new logical device, the CXL subsystem is tasked to take PCIe and ACPI
objects and assemble them into a CXL.mem decode topology. The need for
runtime configuration of the CXL.mem topology is also similar to RAID in
that different environments with the same hardware configuration may
decide to assemble the topology in contrasting ways. One may choose
performance (RAID0) striping memory across multiple Host Bridges and
endpoints while another may opt for fault tolerance and disable any
striping in the CXL.mem topology.
The port driver identifies whether an endpoint Memory Expander is
connected to a CXL topology. If an active (bound to the 'cxl_port'
driver) CXL Port is not found at every PCIe Switch Upstream port and an
active "root" CXL Port then the device is just a plain PCIe endpoint
only capable of participating in PCI.mmio and DMA cycles, not CXL.mem
coherent interleave sets.
The 'cxl_port' driver lets the CXL subsystem leverage driver-core
infrastructure for setup and teardown of register resources and
communicating device activation status to userspace. The cxl_bus_type
can rendezvous the async arrival of platform level CXL resources (via
the 'cxl_acpi' driver) with the asynchronous enumeration of Memory
Expander endpoints, while also implementing a hierarchical locking model
independent of the associated 'struct pci_dev' locking model. The
locking for dport and decoder enumeration is now handled in the core
rather than callers.
For now the port driver only enumerates and registers CXL resources
(downstream port metadata and decoder resources) later it will be used
to take action on its decoders in response to CXL.mem region
provisioning requests.
Note1: cxlpci.h has long depended on pci.h, but port.c was the first to
not include pci.h. Carry that dependency in cxlpci.h.
Note2: cxl port enumeration and probing complicates CXL subsystem init
to the point that it helps to have centralized debug logging of probe
events in cxl_bus_probe().
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Ben Widawsky <ben.widawsky@intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Co-developed-by: Dan Williams <dan.j.williams@intel.com>
Link: https://lore.kernel.org/r/164374948116.464348.1772618057599155408.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Unlike the decoder enumeration for "root decoders" described by platform
firmware, standard decoders can be enumerated from the component
registers space once the base address has been identified (via PCI,
ACPI, or another mechanism).
Add common infrastructure for HDM (Host-managed-Device-Memory) Decoder
enumeration and share it between host-bridge, upstream switch port, and
cxl_test defined decoders.
The locking model for switch level decoders is to hold the port lock
over the enumeration. This facilitates moving the dport and decoder
enumeration to a 'port' driver. For now, the only enumerator of decoder
resources is the cxl_acpi root driver.
Co-developed-by: Ben Widawsky <ben.widawsky@intel.com>
Signed-off-by: Ben Widawsky <ben.widawsky@intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/164374688404.395335.9239248252443123526.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The core houses infrastructure for decoder resources. A CXL port's
dports are more closely related to decoder infrastructure than topology
enumeration. Implement generic PCI based dport enumeration in the core,
i.e. arrange for existing root port enumeration from cxl_acpi to share
code with switch port enumeration which just amounts to a small
difference in a pci_walk_bus() invocation once the appropriate 'struct
pci_bus' has been retrieved.
Set the convention that decoder objects are registered after all dports
are enumerated. This enables userspace to know when the CXL core is
finished establishing 'dportX' links underneath the 'portX' object.
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/164368114191.354031.5270501846455462665.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
In preparation for switch port enumeration while also preserving the
potential for multi-domain / multi-root CXL topologies. Introduce a
'struct device' generic mechanism for retrieving a root CXL port, if one
is registered. Note that the only known multi-domain CXL configurations
are running the cxl_test unit test on a system that also publishes an
ACPI0017 device.
With this in hand the nvdimm-bridge lookup can be with
device_find_child() instead of bus_find_device() + custom mocked lookup
infrastructure in cxl_test.
The mechanism looks for a 2nd level port since the root level topology
is platform-firmware specific and the 2nd level down follows standard
PCIe topology expectations. The cxl_acpi 2nd level is associated with a
PCIe Root Port.
Reported-by: Ben Widawsky <ben.widawsky@intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/164367562182.225521.9488555616768096049.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Add a helper for converting a PCI enumerated cxl_port into the pci_bus
that hosts its dports. For switch ports this is trivial, but for root
ports there is no generic way to go from a platform defined host bridge
device, like ACPI0016 to its corresponding pci_bus. Rather than spill
ACPI goop outside of the cxl_acpi driver, just arrange for it to
register an xarray translation from the uport device to the
corresponding pci_bus.
This is in preparation for centralizing dport enumeration in the core.
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Ben Widawsky <ben.widawsky@intel.com>
Link: https://lore.kernel.org/r/164364745633.85488.9744017377155103992.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Lockdep reports:
======================================================
WARNING: possible circular locking dependency detected
5.16.0-rc1+ #142 Tainted: G OE
------------------------------------------------------
cxl/1220 is trying to acquire lock:
ffff979b85475460 (kn->active#144){++++}-{0:0}, at: __kernfs_remove+0x1ab/0x1e0
but task is already holding lock:
ffff979b87ab38e8 (&dev->lockdep_mutex#2/4){+.+.}-{3:3}, at: cxl_remove_ep+0x50c/0x5c0 [cxl_core]
...where cxl_remove_ep() is a helper that wants to delete ports while
holding a lock on the host device for that port. That sets up a lockdep
violation whereby target_list_show() can not rely holding the decoder's
device lock while walking the target_list. Switch to a dedicated seqlock
for this purpose.
Reported-by: Ben Widawsky <ben.widawsky@intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/164367209095.208169.1171673319121271280.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
When CONFIG_PROVE_LOCKING is enabled the 'struct device' definition gets
an additional mutex that is not clobbered by
lockdep_set_novalidate_class() like the typical device_lock(). This
allows for local annotation of subsystem locks with mutex_lock_nested()
per the subsystem's object/lock hierarchy. For CXL, this primarily needs
the ability to lock ports by depth and child objects of ports by their
parent parent-port lock.
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Ben Widawsky <ben.widawsky@intel.com>
Link: https://lore.kernel.org/r/164365853422.99383.1052399160445197427.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
In preparation for proving CXL subsystem usage of the device_lock()
order track the depth of ports with the expectation that shallower port
locks can be held over deeper port locks.
Signed-off-by: Ben Widawsky <ben.widawsky@intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/164298419321.3018233.4469731547378993606.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Add wrappers for the creation of decoder objects at the root level and
switch level, and keep the core helper private to cxl/core/port.c. Root
decoders are static descriptors conveyed from platform firmware (e.g.
ACPI CFMWS). Switch decoders are CXL standard decoders enumerated via
the HDM decoder capability structure. The base address for the HDM
decoder capability structure may be conveyed either by PCIe or platform
firmware (ACPI CEDT.CHBS).
Additionally, the kdoc descriptions for these helpers and their
dependencies is updated.
Signed-off-by: Ben Widawsky <ben.widawsky@intel.com>
[djbw: fixup changelog, clarify kdoc]
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/164366463014.111117.9714595404002687111.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
CXL decoders manage address ranges in a hierarchical fashion whereby a
leaf is a unique subregion of its parent decoder (midlevel or root). It
therefore makes sense to use the resource API for handling this.
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> (v1)
Signed-off-by: Ben Widawsky <ben.widawsky@intel.com>
Link: https://lore.kernel.org/r/164298417191.3018233.5201055578165414714.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Many CXL drivers simply want to register and unregister themselves.
module_driver already supported this. A simple wrapper around that
reduces a decent amount of boilerplate in upcoming patches.
Suggested-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Ben Widawsky <ben.widawsky@intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/164298415591.3018233.13608495220547681412.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This implements the TODO in cxl_acpi for mapping component registers.
cxl_acpi becomes the second consumer of CXL register block enumeration
(cxl_pci being the first). Moving the functionality to cxl_core allows
both of these drivers to use the functionality. Equally importantly it
allows cxl_core to use the functionality in the future.
CXL 2.0 root ports are similar to CXL 2.0 Downstream Ports with the main
distinction being they're a part of the CXL 2.0 host bridge. While
mapping their component registers is not immediately useful for the CXL
drivers, the movement of register block enumeration into core is a vital
step towards HDM decoder programming.
Signed-off-by: Ben Widawsky <ben.widawsky@intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
[djbw: fix cxl_regmap_to_base() failure cases]
Link: https://lore.kernel.org/r/164298415080.3018233.14694957480228676592.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Commit 48667f6761 ("cxl/core: Split decoder setup into alloc + add")
aimed to fix a large stack frame warning but from v5 to v6, it
introduced a new instance of the warning due to allocating
cxld_const_init on the stack, which was done due to the use of const on
the nr_target member of the cxl_decoder struct. With ARCH=arm
allmodconfig minus CONFIG_KASAN:
GCC 11.2.0:
drivers/cxl/core/bus.c: In function ‘cxl_decoder_alloc’:
drivers/cxl/core/bus.c:523:1: error: the frame size of 1032 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
523 | }
| ^
cc1: all warnings being treated as errors
Clang 12.0.1:
drivers/cxl/core/bus.c:486:21: error: stack frame size of 1056 bytes in function 'cxl_decoder_alloc' [-Werror,-Wframe-larger-than=]
struct cxl_decoder *cxl_decoder_alloc(struct cxl_port *port, int nr_targets)
^
1 error generated.
Revert that part of the change, which makes the stack frame of
cxl_decoder_alloc() much more reasonable.
Fixes: 48667f6761 ("cxl/core: Split decoder setup into alloc + add")
Link: https://github.com/ClangBuiltLinux/linux/issues/1539
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20211210213627.2477370-1-nathan@kernel.org
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
A test of the form:
while true; do modprobe -r cxl_pmem; modprobe cxl_pmem; done
May lead to a crash signature of the form:
BUG: unable to handle page fault for address: ffffffffc0660030
#PF: supervisor instruction fetch in kernel mode
#PF: error_code(0x0010) - not-present page
[..]
Workqueue: cxl_pmem 0xffffffffc0660030
RIP: 0010:0xffffffffc0660030
Code: Unable to access opcode bytes at RIP 0xffffffffc0660006.
[..]
Call Trace:
? process_one_work+0x4ec/0x9c0
? pwq_dec_nr_in_flight+0x100/0x100
? rwlock_bug.part.0+0x60/0x60
? worker_thread+0x2eb/0x700
In that report the 0xffffffffc0660030 address corresponds to the former
function address of cxl_nvb_update_state() from a previous load of the
module, not the current address. Fix that by arranging for ->state_work
in the 'struct cxl_nvdimm_bridge' object to be reinitialized on cxl_pmem
module reload.
Details:
Recall that CXL subsystem wants to link a CXL memory expander device to
an NVDIMM sub-hierarchy when both a persistent memory range has been
registered by the CXL platform driver (cxl_acpi) *and* when that CXL
memory expander has published persistent memory capacity (Get Partition
Info). To this end the cxl_nvdimm_bridge driver arranges to rescan the
CXL bus when either of those conditions change. The helper
bus_rescan_devices() can not be called underneath the device_lock() for
any device on that bus, so the cxl_nvdimm_bridge driver uses a workqueue
for the rescan.
Typically a driver allocates driver data to hold a 'struct work_struct'
for a driven device, but for a workqueue that may run after ->remove()
returns, driver data will have been freed. The 'struct
cxl_nvdimm_bridge' object holds the state and work_struct directly.
Unfortunately it was only arranging for that infrastructure to be
initialized once per device creation rather than the necessary once per
workqueue (cxl_pmem_wq) creation.
Introduce is_cxl_nvdimm_bridge() and cxl_nvdimm_bridge_reset() in
support of invalidating stale references to a recently destroyed
cxl_pmem_wq.
Cc: <stable@vger.kernel.org>
Fixes: 8fdcb1704f ("cxl/pmem: Add initial infrastructure for pmem support")
Reported-by: Vishal Verma <vishal.l.verma@intel.com>
Tested-by: Vishal Verma <vishal.l.verma@intel.com>
Link: https://lore.kernel.org/r/163665474585.3505991.8397182770066720755.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
- Fix support for platforms that do not enumerate every ACPI0016 (CXL
Host Bridge) in the CHBS (ACPI Host Bridge Structure).
- Introduce a common pci_find_dvsec_capability() helper, clean up open
coded implementations in various drivers.
- Add 'cxl_test' for regression testing CXL subsystem ABIs. 'cxl_test'
is a module built from tools/testing/cxl/ that mocks up a CXL topology
to augment the nascent support for emulation of CXL devices in QEMU.
- Convert libnvdimm to use the uuid API.
- Complete the definition of CXL namespace labels in libnvdimm.
- Tunnel libnvdimm label operations from nd_ioctl() back to the CXL
mailbox driver. Enable 'ndctl {read,write}-labels' for CXL.
- Continue to sort and refactor functionality into distinct driver and
core-infrastructure buckets. For example, mailbox handling is now a
generic core capability consumed by the PCI and cxl_test drivers.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQSbo+XnGs+rwLz9XGXfioYZHlFsZwUCYYRtyQAKCRDfioYZHlFs
Z7UsAP9DzUN6IWWnYk1R95YXYVxFriRtRsBjujAqTg49EMghawEAoHaA9lxO3Hho
l25TLYUOmB/zFTlUbe6YQptMJZ5YLwY=
=im9j
-----END PGP SIGNATURE-----
Merge tag 'cxl-for-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/cxl/cxl
Pull cxl updates from Dan Williams:
"More preparation and plumbing work in the CXL subsystem.
From an end user perspective the highlight here is lighting up the CXL
Persistent Memory related commands (label read / write) with the
generic ioctl() front-end in LIBNVDIMM.
Otherwise, the ability to instantiate new persistent and volatile
memory regions is still on track for v5.17.
Summary:
- Fix support for platforms that do not enumerate every ACPI0016 (CXL
Host Bridge) in the CHBS (ACPI Host Bridge Structure).
- Introduce a common pci_find_dvsec_capability() helper, clean up
open coded implementations in various drivers.
- Add 'cxl_test' for regression testing CXL subsystem ABIs.
'cxl_test' is a module built from tools/testing/cxl/ that mocks up
a CXL topology to augment the nascent support for emulation of CXL
devices in QEMU.
- Convert libnvdimm to use the uuid API.
- Complete the definition of CXL namespace labels in libnvdimm.
- Tunnel libnvdimm label operations from nd_ioctl() back to the CXL
mailbox driver. Enable 'ndctl {read,write}-labels' for CXL.
- Continue to sort and refactor functionality into distinct driver
and core-infrastructure buckets. For example, mailbox handling is
now a generic core capability consumed by the PCI and cxl_test
drivers"
* tag 'cxl-for-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/cxl/cxl: (34 commits)
ocxl: Use pci core's DVSEC functionality
cxl/pci: Use pci core's DVSEC functionality
PCI: Add pci_find_dvsec_capability to find designated VSEC
cxl/pci: Split cxl_pci_setup_regs()
cxl/pci: Add @base to cxl_register_map
cxl/pci: Make more use of cxl_register_map
cxl/pci: Remove pci request/release regions
cxl/pci: Fix NULL vs ERR_PTR confusion
cxl/pci: Remove dev_dbg for unknown register blocks
cxl/pci: Convert register block identifiers to an enum
cxl/acpi: Do not fail cxl_acpi_probe() based on a missing CHBS
cxl/pci: Disambiguate cxl_pci further from cxl_mem
Documentation/cxl: Add bus internal docs
cxl/core: Split decoder setup into alloc + add
tools/testing/cxl: Introduce a mock memory device + driver
cxl/mbox: Move command definitions to common location
cxl/bus: Populate the target list at decoder create
tools/testing/cxl: Introduce a mocked-up CXL port hierarchy
cxl/pmem: Add support for multiple nvdimm-bridge objects
cxl/pmem: Translate NVDIMM label commands to CXL label commands
...
In addition to carrying @barno, @block_offset, and @reg_type, add @base
to keep all map/unmap parameters in one object. The helpers
cxl_{map,unmap}_regblock() handle adjusting @base to the @block_offset
at map and unmap time.
Document that @base incorporates @block_offset so that downstream
consumers of a mapped cxl_register_map instance do not need perform any
fixups / can use @base directly.
Cc: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/163433497228.889435.11271988238496181536.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Use the newly introduced struct_group_typed() macro to clean up the
declaration of struct cxl_regs.
Cc: Alison Schofield <alison.schofield@intel.com>
Cc: Vishal Verma <vishal.l.verma@intel.com>
Cc: Ira Weiny <ira.weiny@intel.com>
Cc: Ben Widawsky <ben.widawsky@intel.com>
Cc: linux-cxl@vger.kernel.org
Suggested-by: Dan Williams <dan.j.williams@intel.com>
Link: https://lore.kernel.org/lkml/1d9a2e6df2a9a35b2cdd50a9a68cac5991e7e5f0.camel@intel.com
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
The kbuild robot reports:
drivers/cxl/core/bus.c:516:1: warning: stack frame size (1032) exceeds
limit (1024) in function 'devm_cxl_add_decoder'
It is also the case the devm_cxl_add_decoder() is unwieldy to use for
all the different decoder types. Fix the stack usage by splitting the
creation into alloc and add steps. This also allows for context
specific construction before adding.
With the split the caller is responsible for registering a devm callback
to trigger device_unregister() for the decoder rather than it being
implicit in the decoder registration. I.e. the routine that calls alloc
is responsible for calling put_device() if the "add" operation fails.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Nathan Chancellor <nathan@kernel.org>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Ben Widawsky <ben.widawsky@intel.com>
Link: https://lore.kernel.org/r/163225205828.3038145.6831131648369404859.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Introduce an emulated device-set plus driver to register CXL memory
devices, 'struct cxl_memdev' instances, in the mock cxl_test topology.
This enables the development of HDM Decoder (Host-managed Device Memory
Decoder) programming flow (region provisioning) in an environment that
can be updated alongside the kernel as it gains more functionality.
Whereas the cxl_pci module looks for CXL memory expanders on the 'pci'
bus, the cxl_mock_mem module attaches to CXL expanders on the platform
bus emitted by cxl_test.
Acked-by: Ben Widawsky <ben.widawsky@intel.com>
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/163116440099.2460985.10692549614409346604.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
As found by cxl_test, the implementation populated the target_list for
the single dport exceptional case, it missed populating the target_list
for the typical multi-dport case. Root decoders always know their target
list at the beginning of time, and even switch-level decoders should
have a target list of one or more zeros by default, depending on the
interleave-ways setting.
Walk the hosting port's dport list and populate based on the passed in
map.
Move devm_cxl_add_passthrough_decoder() out of line now that it does the
work of generating a target_map.
Before:
$ cat /sys/bus/cxl/devices/root2/decoder*/target_list
0
0
After:
$ cat /sys/bus/cxl/devices/root2/decoder*/target_list
0
0,1,2,3
0
0,1,2,3
Where root2 is a CXL topology root object generated by 'cxl_test'.
Acked-by: Ben Widawsky <ben.widawsky@intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/163116439000.2460985.11713777051267946018.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Create an environment for CXL plumbing unit tests. Especially when it
comes to an algorithm for HDM Decoder (Host-managed Device Memory
Decoder) programming, the availability of an in-kernel-tree emulation
environment for CXL configuration complexity and corner cases speeds
development and deters regressions.
The approach taken mirrors what was done for tools/testing/nvdimm/. I.e.
an external module, cxl_test.ko built out of the tools/testing/cxl/
directory, provides mock implementations of kernel APIs and kernel
objects to simulate a real world device hierarchy.
One feedback for the tools/testing/nvdimm/ proposal was "why not do this
in QEMU?". In fact, the CXL development community has developed a QEMU
model for CXL [1]. However, there are a few blocking issues that keep
QEMU from being a tight fit for topology + provisioning unit tests:
1/ The QEMU community has yet to show interest in merging any of this
support that has had patches on the list since November 2020. So,
testing CXL to date involves building custom QEMU with out-of-tree
patches.
2/ CXL mechanisms like cross-host-bridge interleave do not have a clear
path to be emulated by QEMU without major infrastructure work. This
is easier to achieve with the alloc_mock_res() approach taken in this
patch to shortcut-define emulated system physical address ranges with
interleave behavior.
The QEMU enabling has been critical to get the driver off the ground,
and may still move forward, but it does not address the ongoing needs of
a regression testing environment and test driven development.
This patch adds an ACPI CXL Platform definition with emulated CXL
multi-ported host-bridges. A follow on patch adds emulated memory
expander devices.
Acked-by: Ben Widawsky <ben.widawsky@intel.com>
Reported-by: Vishal Verma <vishal.l.verma@intel.com>
Link: https://lore.kernel.org/r/20210202005948.241655-1-ben.widawsky@intel.com [1]
Link: https://lore.kernel.org/r/163164680798.2831381.838684634806668012.stgit@dwillia2-desk3.amr.corp.intel.com
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
In preparation for a mocked unit test environment for CXL objects, allow
for multiple unique nvdimm-bridge objects.
For now, just allow multiple bridges to be registered. Later, when there
are multiple present, further updates are needed to
cxl_find_nvdimm_bridge() to identify which bridge is associated with
which CXL hierarchy for nvdimm registration.
Note that this does change the kernel device-name for the bridge object.
User space should not have any attachment to the device name at this
point as it is still early days in the CXL driver development.
Acked-by: Ben Widawsky <ben.widawsky@intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/163164647007.2831228.2150246954620721526.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
It is desirable to retain the mappings from the calling function. By
simplifying this code, it will be much more straightforward to do that.
Signed-off-by: Ben Widawsky <ben.widawsky@intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/20210716231548.174778-3-ben.widawsky@intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
While a memX device on /sys/bus/cxl represents a CXL memory expander
control interface, a pmemX device represents the persistent memory
sub-functionality. It bridges the CXL subystem to the libnvdimm nmemX
control interface.
With this skeleton ndctl can now see persistent memory devices on a
"CXL" bus. Later patches add support for translating libnvdimm native
commands to CXL commands.
# ndctl list -BDiu -b CXL
{
"provider":"CXL",
"dev":"ndbus1",
"dimms":[
{
"dev":"nmem1",
"state":"disabled"
},
{
"dev":"nmem0",
"state":"disabled"
}
]
}
Given nvdimm_bus_unregister() removes all devices on an ndbus0 the
cxl_pmem infrastructure needs to arrange ->remove() to be triggered on
cxl_nvdimm devices to keep their enabled state synchronized with the
registration state of their corresponding device on the nvdimm_bus. In
other words, always arrange for cxl_nvdimm_driver.remove() to unregister
nvdimms from an nvdimm_bus ahead of the bus being unregistered.
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/162380012696.3039556.4293801691038740850.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Register an 'nvdimm-bridge' device to act as an anchor for a libnvdimm
bus hierarchy. Also, flesh out the cxl_bus definition to allow a
cxl_nvdimm_bridge_driver to attach to the bridge and trigger the
nvdimm-bus registration.
The creation of the bridge is gated on the detection of a PMEM capable
address space registered to the root. The bridge indirection allows the
libnvdimm module to remain unloaded on platforms without PMEM support.
Given that the probing of ACPI0017 is asynchronous to CXL endpoint
devices, and the expectation that CXL endpoint devices register other
PMEM resources on the 'CXL' nvdimm bus, a workqueue is added. The
workqueue is needed to run bus_rescan_devices() outside of the
device_lock() of the nvdimm-bridge device to rendezvous nvdimm resources
as they arrive. For now only the bus is taken online/offline in the
workqueue.
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/162379909706.2993820.14051258608641140169.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Enable devices on the 'cxl' bus to be attached to drivers. The initial
user of this functionality is a driver for an 'nvdimm-bridge' device
that anchors a libnvdimm hierarchy attached to CXL persistent memory
resources. Other device types that will leverage this include:
cxl_port: map and use component register functionality (HDM Decoders)
cxl_nvdimm: translate CXL memory expander endpoints to libnvdimm
'nvdimm' objects
cxl_region: translate CXL interleave sets to libnvdimm 'region' objects
The pairing of devices to drivers is handled through the cxl_device_id()
matching to cxl_driver.id values. A cxl_device_id() of '0' indicates no
driver support.
In addition to ->match(), ->probe(), and ->remove() support for the
'cxl' bus introduce MODULE_ALIAS_CXL() to autoload modules containing
cxl-drivers. Drivers are added in follow-on changes.
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/162379909190.2993820.6134168109678004186.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The decoder count in the HDM decoder capability structure is an encoded
field. As defined in the spec:
Decoder Count: Reports the number of memory address decoders implemented
by the component.
0 – 1 Decoder
1 – 2 Decoders
2 – 4 Decoders
3 – 6 Decoders
4 – 8 Decoders
5 – 10 Decoders
All other values are reserved
Nothing is actually fixed by this as nothing actually used this mapping
yet.
Cc: Ira Weiny <ira.weiny@intel.com>
Fixes: 08422378c4 ("cxl/pci: Add HDM decoder capabilities")
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Ben Widawsky <ben.widawsky@intel.com>
Link: https://lore.kernel.org/r/20210611190111.121295-1-ben.widawsky@intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
A cxl_decoder is a child of a cxl_port. It represents a hardware decoder
configuration of an upstream port to one or more of its downstream
ports. The decoder is either represented in CXL standard HDM decoder
registers (see CXL 2.0 section 8.2.5.12 CXL HDM Decoder Capability
Structure), or it is a static decode configuration communicated by
platform firmware (see the CXL Early Discovery Table: Fixed Memory
Window Structure).
The firmware described and hardware described decoders differ slightly
leading to 2 different sub-types of decoders, cxl_decoder_root and
cxl_decoder_switch. At the root level the decode capabilities restrict
what can be mapped beneath them. Mid-level switch decoders are
configured for either acclerator (type-2) or memory-expander (type-3)
operation, but they are otherwise agnostic to the type of memory
(volatile vs persistent) being mapped.
Here is an example topology from a single-ported host-bridge environment
without CFMWS decodes enumerated.
/sys/bus/cxl/devices/root0
├── devtype
├── dport0 -> ../../../LNXSYSTM:00/LNXSYBUS:00/ACPI0016:00
├── port1
│ ├── decoder1.0
│ │ ├── devtype
│ │ ├── locked
│ │ ├── size
│ │ ├── start
│ │ ├── subsystem -> ../../../../../../bus/cxl
│ │ ├── target_list
│ │ ├── target_type
│ │ └── uevent
│ ├── devtype
│ ├── dport0 -> ../../../../pci0000:34/0000:34:00.0
│ ├── subsystem -> ../../../../../bus/cxl
│ ├── uevent
│ └── uport -> ../../../../LNXSYSTM:00/LNXSYBUS:00/ACPI0016:00
├── subsystem -> ../../../../bus/cxl
├── uevent
└── uport -> ../../ACPI0017:00
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/162325695128.2293823.17519927266014762694.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
In preparation for infrastructure that enumerates and configures the CXL
decode mechanism of an upstream port to its downstream ports, add a
representation of a CXL downstream port.
On ACPI systems the top-most logical downstream ports in the hierarchy
are the host bridges (ACPI0016 devices) that decode the memory windows
described by the CXL Early Discovery Table Fixed Memory Window
Structures (CEDT.CFMWS).
Reviewed-by: Alison Schofield <alison.schofield@intel.com>
Link: https://lore.kernel.org/r/162325450624.2293126.3533006409920271718.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
While CXL builds upon the PCI software model for enumeration and
endpoint control, a static platform component is required to bootstrap
the CXL memory layout. Similar to how ACPI identifies root-level PCI
memory resources, ACPI data enumerates the address space and interleave
configuration for CXL Memory.
In addition to identifying host bridges, ACPI is responsible for
enumerating the CXL memory space that can be addressed by downstream
decoders. This is similar to the requirement for ACPI to publish
resources via the _CRS method for PCI host bridges. Specifically, ACPI
publishes a table, CXL Early Discovery Table (CEDT), which includes a
list of CXL Memory resources, CXL Fixed Memory Window Structures
(CFMWS).
For now, introduce the core infrastructure for a cxl_port hierarchy
starting with a root level anchor represented by the ACPI0017 device.
Follow on changes model support for the configurable decode capabilities
of cxl_port instances, i.e. CXL switch support.
Co-developed-by: Alison Schofield <alison.schofield@intel.com>
Signed-off-by: Alison Schofield <alison.schofield@intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/162325449515.2293126.15303270193010154608.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
An HDM decoder is defined in the CXL 2.0 specification as a mechanism
that allow devices and upstream ports to claim memory address ranges and
participate in interleave sets. HDM decoder registers are within the
component register block defined in CXL 2.0 8.2.3 CXL 2.0 Component
Registers as part of the CXL.cache and CXL.mem subregion.
The Component Register Block is found via the Register Locator DVSEC
in a similar fashion to how the CXL Device Register Block is found. The
primary difference is the capability id size of the Component Register
Block is a single DWORD instead of 4 DWORDS.
It's now possible to configure a CXL type 3 device's HDM decoder. Such
programming is expected for CXL devices with persistent memory, and hot
plugged CXL devices that participate in CXL.mem with volatile memory.
Add probe and mapping functions for the component register blocks.
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Co-developed-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Co-developed-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Ben Widawsky <ben.widawsky@intel.com>
Link: https://lore.kernel.org/r/20210528004922.3980613-6-ira.weiny@intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The information required to map registers based on capabilities is
contained within the bars themselves. This means the bar must be mapped
to read the information needed and then unmapped to map the individual
parts of the BAR based on capabilities.
Change cxl_setup_device_regs() to return a new cxl_register_map, change
the name to cxl_probe_device_regs(). Allocate and place
cxl_register_maps on a list while processing all of the specified
register blocks.
After probing all the register blocks go back and map smaller registers
blocks based on their capabilities and dispose of the cxl_register_maps.
NOTE: pci_iomap() is not managed automatically via pcim_enable_device()
so be careful to call pci_iounmap() correctly.
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Link: https://lore.kernel.org/r/20210604005036.4187184-1-ira.weiny@intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
While CXL Memory Device endpoints locate the CXL MMIO registers in a PCI
BAR, CXL root bridges have their MMIO base address described by platform
firmware. Refactor the existing register lookup into a generic facility
for endpoints and bridges to share.
Reviewed-by: Ben Widawsky <ben.widawsky@intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/162096972534.1865304.3218686216153688039.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
CXL MMIO register blocks are organized by device type and capabilities.
There are Component registers, Device registers (yes, an ambiguous
name), and Memory Device registers (a specific extension of Device
registers).
It is possible for a given device instance (endpoint or port) to
implement register sets from multiple of the above categories.
The driver code that enumerates and maps the registers is type specific
so it is useful to have a dedicated type and helpers for each block
type.
At the same time, once the registers are mapped the origin type does not
matter. It is overly pedantic to reference the register block type in
code that is using the registers.
In preparation for the endpoint driver to incorporate Component registers
into its MMIO operations reorganize the registers to allow typed
enumeration + mapping, but anonymous usage. With the end state of
'struct cxl_regs' to be:
struct cxl_regs {
union {
struct {
CXL_DEVICE_REGS();
};
struct cxl_device_regs device_regs;
};
union {
struct {
CXL_COMPONENT_REGS();
};
struct cxl_component_regs component_regs;
};
};
With this arrangement the driver can share component init code with
ports, but when using the registers it can directly reference the
component register block type by name without the 'component_regs'
prefix.
So, map + enumerate can be shared across drivers of different CXL
classes e.g.:
void cxl_setup_device_regs(struct device *dev, void __iomem *base,
struct cxl_device_regs *regs);
void cxl_setup_component_regs(struct device *dev, void __iomem *base,
struct cxl_component_regs *regs);
...while inline usage in the driver need not indicate where the
registers came from:
readl(cxlm->regs.mbox + MBOX_OFFSET);
readl(cxlm->regs.hdm + HDM_OFFSET);
...instead of:
readl(cxlm->regs.device_regs.mbox + MBOX_OFFSET);
readl(cxlm->regs.component_regs.hdm + HDM_OFFSET);
This complexity of the definition in .h yields improvement in code
readability in .c while maintaining type-safety for organization of
setup code. It prepares the implementation to maintain organization in
the face of CXL devices that compose register interfaces consisting of
multiple types.
Given that this new container is named 'regs' rename the common register
base pointer @base, and fixup the kernel-doc for the missing @cxlmd
description.
Reviewed-by: Ben Widawsky <ben.widawsky@intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/162096971451.1865304.13540251513463515153.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
In preparation for sharing cxl.h with other generic CXL consumers,
move / consolidate some of the memory device specifics to mem.h.
The motivation for moving out of cxl.h is to maintain least privilege
access to memory-device details since cxl.h is used in multiple files.
The motivation for moving definitions into a new mem.h header is for
code readability and organization. I.e. minimize implementation details
when reading data structures and other definitions.
Reviewed-by: Ben Widawsky <ben.widawsky@intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/162096970932.1865304.14510894426562947262.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
CXL devices identified by the memory-device class code must implement
the Device Command Interface (described in 8.2.9 of the CXL 2.0 spec).
While the driver already maintains a list of commands it supports, there
is still a need to be able to distinguish between commands that the
driver knows about from commands that are optionally supported by the
hardware.
The Command Effects Log (CEL) is specified in the CXL 2.0 specification.
The CEL is one of two types of logs, the other being vendor specific.
They are distinguished in hardware/spec via UUID. The CEL is useful for
2 things:
1. Determine which optional commands are supported by the CXL device.
2. Enumerate any vendor specific commands
The CEL is used by the driver to determine which commands are available
in the hardware and therefore which commands userspace is allowed to
execute. The set of enabled commands might be a subset of commands which
are advertised in UAPI via CXL_MEM_SEND_COMMAND IOCTL.
With the CEL enabling comes a internal flag to indicate a base set of
commands that are enabled regardless of CEL. Such commands are required
for basic interaction with the hardware and thus can be useful in debug
cases, for example if the CEL is corrupted.
The implementation leaves the statically defined table of commands and
supplements it with a bitmap to determine commands that are enabled.
This organization was chosen for the following reasons:
- Smaller memory footprint. Doesn't need a table per device.
- Reduce memory allocation complexity.
- Fixed command IDs to opcode mapping for all devices makes development
and debugging easier.
- Certain helpers are easily achievable, like cxl_for_each_cmd().
Signed-off-by: Ben Widawsky <ben.widawsky@intel.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com> (v2)
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> (v3)
Link: https://lore.kernel.org/r/20210217040958.1354670-7-ben.widawsky@intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Create the /sys/bus/cxl hierarchy to enumerate:
* Memory Devices (per-endpoint control devices)
* Memory Address Space Devices (platform address ranges with
interleaving, performance, and persistence attributes)
* Memory Regions (active provisioned memory from an address space device
that is in use as System RAM or delegated to libnvdimm as Persistent
Memory regions).
For now, only the per-endpoint control devices are registered on the
'cxl' bus. However, going forward it will provide a mechanism to
coordinate cross-device interleave.
Signed-off-by: Ben Widawsky <ben.widawsky@intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> (v2)
Link: https://lore.kernel.org/r/20210217040958.1354670-4-ben.widawsky@intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Provide enough functionality to utilize the mailbox of a memory device.
The mailbox is used to interact with the firmware running on the memory
device. The flow is proven with one implemented command, "identify".
Because the class code has already told the driver this is a memory
device and the identify command is mandatory.
CXL devices contain an array of capabilities that describe the
interactions software can have with the device or firmware running on
the device. A CXL compliant device must implement the device status and
the mailbox capability. Additionally, a CXL compliant memory device must
implement the memory device capability. Each of the capabilities can
[will] provide an offset within the MMIO region for interacting with the
CXL device.
The capabilities tell the driver how to find and map the register space
for CXL Memory Devices. The registers are required to utilize the CXL
spec defined mailbox interface. The spec outlines two mailboxes, primary
and secondary. The secondary mailbox is earmarked for system firmware,
and not handled in this driver.
Primary mailboxes are capable of generating an interrupt when submitting
a background command. That implementation is saved for a later time.
Reported-by: Colin Ian King <colin.king@canonical.com> (coverity)
Reported-by: Dan Carpenter <dan.carpenter@oracle.com> (smatch)
Signed-off-by: Ben Widawsky <ben.widawsky@intel.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com> (v2)
Link: https://www.computeexpresslink.org/download-the-specification
Link: https://lore.kernel.org/r/20210217040958.1354670-3-ben.widawsky@intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
