When an NFC-DEP Initiator receives a frame with
an incorrect CRC or with a parity error, and the
frame is at least 4 bytes long, its supposed to
send a NACK to the Target. The Initiator can
send up to 'N(retry,nack)' consecutive NACKs
where 2 <= 'N(retry,nack)' <= 5. When the limit
is exceeded, a PROTOCOL EXCEPTION is raised.
Any other type of transmission error is to be
ignored and the Initiator should continue
waiting for a new frame. This is described
in section 14.12.5.4 of the NFC Digital Protocol
Spec.
The digital layer's NFC-DEP code doesn't implement
any of this so add it. This support diverges from
the spec in two significant ways:
a) NACKs will be sent for ANY error reported by the
driver except a timeout. This is done because
there is currently no way for the digital layer
to distinguish a CRC or parity error from any
other type of error reported by the driver.
b) All other errors will cause a PROTOCOL EXCEPTION
even frames with CRC errors that are less than 4
bytes.
The value chosen for 'N(retry,nack)' is 2.
Targets do not send NACK PDUs.
Reviewed-by: Thierry Escande <thierry.escande@linux.intel.com>
Tested-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When the peer in an NFC-DEP exchange has a
packet to send that is larger than the local
maximum payload, it sets the 'MI' bit in the
'I' PDU. This indicates that NFC-DEP chaining
is to occur.
When such a PDU is received, the local side
responds with an 'ACK' PDU and this continues
until the peer sends an 'I' PDU with the 'MI'
bit cleared. This indicates that the chaining
sequence is complete and the entire packet has
been transferred.
Receiving chained PDUs is currently not supported
by the digital layer so add that support. When a
chaining sequence is initiated by the peer, the
digital layer will allocate an skb large enough
to hold 8 maximum sized frame payloads. The maximum
payload can range from 64 to 254 bytes so 8 * 254 =
2032 seems like a reasonable compromise between
potentially wasting memory and constantly reallocating
new, larger skbs.
Reviewed-by: Thierry Escande <thierry.escande@linux.intel.com>
Tested-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When the NFC-DEP code is given a packet to send
that is larger than the peer's maximum payload,
its supposed to set the 'MI' bit in the 'I' PDU's
Protocol Frame Byte (PFB). Setting this bit
indicates that NFC-DEP chaining is to occur.
When NFC-DEP chaining is progress, sender 'I' PDUs
are acknowledged with 'ACK' PDUs until the last 'I'
PDU in the chain (which has the 'MI' bit cleared)
is responded to with a normal 'I' PDU. This can
occur while in Initiator mode or in Target mode.
Sender NFC-DEP chaining is currently not implemented
in the digital layer so add that support. Unfortunately,
since sending a frame may require writing the CRC to the
end of the data, the relevant data part of the original
skb must be copied for each intermediate frame.
Reviewed-by: Thierry Escande <thierry.escande@linux.intel.com>
Tested-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The maximum payload for NFC-DEP exchanges (i.e., the
number of bytes between SoD and EoD) is negotiated
using the ATR_REQ, ATR_RES, and PSL_REQ commands.
The valid maximum lengths are 64, 128, 192, and 254
bytes.
Currently, NFC-DEP code assumes that both sides are
always using 254 byte maximums and ignores attempts
by the peer to change it. Instead, implement the
negotiation code, enforce the local maximum when
receiving data from the peer, and don't send payloads
that exceed the remote's maximum. The default local
maximum is 254 bytes.
Reviewed-by: Thierry Escande <thierry.escande@linux.intel.com>
Tested-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
NFC-DEP DEP_REQ and DEP_RES exchanges using 'I'
and 'ACK/NACK' PDUs have a sequence number called
the Packet Number Information (PNI). The PNI
is incremented (modulo 4) after every DEP_REQ/
DEP_RES pair and should be verified by the digital
layer code. That verification isn't always done,
though, so add code to make sure that it is done.
Reviewed-by: Thierry Escande <thierry.escande@linux.intel.com>
Tested-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
According to chapter 14 of the NFC-DEP Digital
Protocol Spec., the NAD byte should never be
present in DEP_REQ or DEP_RES frames. However,
this is not enforced so add that enforcement code.
Reviewed-by: Thierry Escande <thierry.escande@linux.intel.com>
Tested-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When in Target mode, the Initiator specifies whether
subsequent DEP_REQ and DEP_RES frames will include
a DID byte by the value passed in the ATR_REQ. If
the DID value in the ATR_REQ is '0' then no DID
byte will be included. If the DID value is between
'1' and '14' then a DID byte containing the same
value must be included in subsequent DEP_REQ and
DEP_RES frames. Any other DID value is invalid.
This is specified in sections 14.8.1.2 and 14.8.2.2
of the NFC Digital Protocol Spec.
Checking the DID value (if it should be there at all),
is not currently supported by the digital layer's
NFC-DEP code. Add this support by remembering the
DID value in the ATR_REQ, checking the DID value of
received DEP_REQ frames (if it should be there at all),
and including the remembered DID value in DEP_RES
frames when appropriate.
Reviewed-by: Thierry Escande <thierry.escande@linux.intel.com>
Tested-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When in Initiator mode, the digital layer's
NFC-DEP code always sets the Device ID (DID)
value in the ATR_REQ to '0'. This means that
subsequent DEP_REQ and DEP_RES frames must
never include a DID byte. This is specified
in sections 14.8.1.1 and 14.8.2.1 of the NFC
Digital Protocol Spec.
Currently, the digital layer's NFC-DEP code
doesn't enforce this rule so add code to ensure
that there is no DID byte in DEP_RES frames.
Reviewed-by: Thierry Escande <thierry.escande@linux.intel.com>
Tested-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Rearrange some of the code in digital_in_recv_dep_res()
and digital_tg_recv_dep_req() so the initial code looks
similar. The real reason is prepare the code for some
upcoming patches that require these changes.
Reviewed-by: Thierry Escande <thierry.escande@linux.intel.com>
Tested-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When digital_in_send_cmd() or digital_tg_send_cmd()
fail, they do not free the skb that was passed to
them so the routine that allocated the skb should
free it. Currently, there are several routines in
the NFC-DEP code that don't do this so make them.
Reviewed-by: Thierry Escande <thierry.escande@linux.intel.com>
Tested-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This encapsulates all of the skb_copy_datagram_iovec() callers
with call argument signature "skb, offset, msghdr->msg_iov, length".
When we move to iov_iters in the networking, the iov_iter object will
sit in the msghdr.
Having a helper like this means there will be less places to touch
during that transformation.
Based upon descriptions and patch from Al Viro.
Signed-off-by: David S. Miller <davem@davemloft.net>
In NFC Forum NCI specification, some RF Protocol values are
reserved for proprietary use (from 0x80 to 0xfe).
Some CLF vendor may need to use one value within this range
for specific technology.
Furthermore, some CLF may not becompliant with NFC Froum NCI
specification 2.0 and therefore will not support RF Protocol
value 0x06 for PROTOCOL_T5T as mention in a draft specification
and in a recent push.
Adding get_rf_protocol handle to the nci_ops structure will
help to set the correct technology to target.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
NCI RF FRAME interface is used for all kind of tags
except ISODEP ones. So for all other kind of tags the
status byte has to be removed.
Signed-off-by: Vincent Cuissard <cuissard@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
All contexts have to be initiliazed before calling
nfc_register_device otherwise it is possible to call
nci_dev_up before ending the nci_register_device
function. In such case kernel will crash on non
initialized variables.
Signed-off-by: Vincent Cuissard <cuissard@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In order to operate at the fasted bit rate
possible, add initiator-side support for
PSL REQ while in P2P mode. The PSL REQ
will switch the RF technology to 424F
whenever possible.
Reviewed-by: Thierry Escande <thierry.escande@linux.intel.com>
Tested-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Conflicts:
net/6lowpan/iphc.c
Minor conflicts in iphc.c were changes overlapping with some
style cleanups.
John W. Linville says:
====================
Please pull this last(?) batch of wireless change intended for the
3.17 stream...
For the NFC bits, Samuel says:
"This is a rather quiet one, we have:
- A new driver from ST Microelectronics for their NCI ST21NFCB,
including device tree support.
- p2p support for the ST21NFCA driver
- A few fixes an enhancements for the NFC digital laye"
For the Atheros bits, Kalle says:
"Michal and Janusz did some important RX aggregation fixes, basically we
were missing RX reordering altogether. The 10.1 firmware doesn't support
Ad-Hoc mode and Michal fixed ath10k so that it doesn't advertise Ad-Hoc
support with that firmware. Also he implemented a workaround for a KVM
issue."
For the Bluetooth bits, Gustavo and Johan say:
"To quote Gustavo from his previous request:
'Some last minute fixes for -next. We have a fix for a use after free in
RFCOMM, another fix to an issue with ADV_DIRECT_IND and one for ADV_IND with
auto-connection handling. Last, we added support for reading the codec and
MWS setting for controllers that support these features.'
Additionally there are fixes to LE scanning, an update to conform to the 4.1
core specification as well as fixes for tracking the page scan state. All
of these fixes are important for 3.17."
And,
"We've got:
- 6lowpan fixes/cleanups
- A couple crash fixes, one for the Marvell HCI driver and another in LE SMP.
- Fix for an incorrect connected state check
- Fix for the bondable requirement during pairing (an issue which had
crept in because of using "pairable" when in fact the actual meaning
was "bondable" (these have different meanings in Bluetooth)"
Along with those are some late-breaking hardware support patches in
brcmfmac and b43 as well as a stray ath9k patch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The digital layer of the NFC subsystem currently
supports a 'tg_listen_mdaa' driver hook that supports
devices that can do mode detection and automatic
anticollision. However, there are some devices that
can do mode detection but not automatic anitcollision
so add the 'tg_listen_md' hook to support those devices.
In order for the digital layer to get the RF technology
detected by the device from the driver, add the
'tg_get_rf_tech' hook. It is only valid to call this
hook immediately after a successful call to 'tg_listen_md'.
CC: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
stop_poll allows to stop CLF reader polling. Some other operations might be
necessary for some CLF to stop polling. For example in card mode.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add T1T matching with Jewel during notification.
It was causing "the target found does not have the desired protocol"
to show up.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add new "NFC_DIGITAL_FRAMING_*" calls to the digital
layer so the driver can make the necessary adjustments
when performing anticollision while in target mode.
The driver must ensure that the effect of these calls
happens after the following response has been sent but
before reception of the next request begins.
Acked-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Currently, digital_target_found() has a race between
the events started by calling nfc_targets_found()
(which ultimately expect ddev->poll_tech_count to be
zero) and setting ddev->poll_tech_count to zero after
the call to nfc_targets_found(). When the race is
"lost" (i.e., ddev->poll_tech_count is found to not
be zero by the events started by nfc_targets_found()),
an error message is printed and the target is not found.
A similar race exists when digital_tg_recv_atr_req()
calls nfc_tm_activated().
Fix this by first saving the current value of
ddev->poll_tech_count and then clearing it before
calling nfc_targets_found()/nfc_tm_activated().
Clearing ddev->poll_tech_count before calling
nfc_targets_found()/nfc_tm_activated() eliminates
the race. Saving the value is required so it can be
restored when nfc_targets_found()/nfc_tm_activated()
fails and polling needs to continue.
Acked-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In digital_in_recv_sel_res(), the code that determines
the tag type will interpret bits 7:6 (lsb being b1 as
per the Digital Specification) of a SEL RES set to 11b
as a Type 4 tag. This is okay except that the neard
will interpret the same value as an NFC-DEP device
(in src/tag.c:set_tag_type() in the neard source).
Make the digital layer's interpretation match neard's
interpretation by changing the order of the checks in
digital_in_recv_sel_res() so that a value of 11b in
bits 7:6 is interpreted as an NFC-DEP device instead
of a Type 4 tag.
Acked-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
There are several instances where a pskb_copy or __pskb_copy is
immediately followed by an skb_clone.
Add a couple of new functions to allow the copy skb to be allocated
from the fclone cache and thus speed up subsequent skb_clone calls.
Cc: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Marek Lindner <mareklindner@neomailbox.ch>
Cc: Simon Wunderlich <sw@simonwunderlich.de>
Cc: Antonio Quartulli <antonio@meshcoding.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Gustavo Padovan <gustavo@padovan.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Arvid Brodin <arvid.brodin@alten.se>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Pablo Neira Ayuso <pablo@netfilter.org>
Cc: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Cc: Lauro Ramos Venancio <lauro.venancio@openbossa.org>
Cc: Aloisio Almeida Jr <aloisio.almeida@openbossa.org>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Jon Maloy <jon.maloy@ericsson.com>
Cc: Allan Stephens <allan.stephens@windriver.com>
Cc: Andrew Hendry <andrew.hendry@gmail.com>
Cc: Eric Dumazet <edumazet@google.com>
Reviewed-by: Christoph Paasch <christoph.paasch@uclouvain.be>
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change adds some entropy to polling cycles, choosing the next
polling rf technology randomly. This reflects the change done in the
pn533 driver, avoiding possible infinite loop for devices that export 2
targets on 2 different modulations. If the first target is not
readable, we will stay in an error loop for ever.
Signed-off-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The error code returned by digital_in_send_cmd() was not returned by
digital_in_send_atr_req().
Signed-off-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
So that anyone listening on SOCKPROTO_RAW for raw frames will get all
NCI frames, in both directions. This actually implements userspace NFC
NCI sniffing.
It's now up to userspace to decode those frames.
Signed-off-by: Hiren Tandel <hirent@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This allows for a more generic NFC sniffing by using SOCKPROTO_RAW
SOCK_RAW to read RAW NFC frames. This is for sniffing anything but LLCP
(HCI, NCI, etc...).
Signed-off-by: Hiren Tandel <hirent@marvell.com>
Signed-off-by: Rahul Tank <rahult@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
ATR_RES response received within Activation Parameters is already
in correct order. Reversing it fails LLCP magic number check and
so P2P functionality fails.
Signed-off-by: Hiren Tandel <hirent@marvell.com>
Signed-off-by: Rahul Tank <rahult@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
According to section 5.15.1.3 of the NFC Activity
Specification, multiple SENSF_REQ commands can be
received by a target before it receives an ATR_REQ
command. To handle this, add a routine that checks
whether a SENSF_REQ or ATR_REQ has been recieved.
If its a SENSF_REQ, respond appropriately and
continue waiting for a ATR_REQ. If its an ATR_REQ,
handle it as before.
CC: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The check in digital_tg_send_sensf_res() that excludes
the 'RD' field from the SENSF_RES is inverted. The 'RD'
field should be excluded when the SENSF_REQ 'RC' field
is equal to DIGITAL_SENSF_REQ_RC_NONE instead of when
its not equal. This is described in section 6.6.2.11
of the NFC Digital Specification.
CC: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Fixing "sparse: cast to restricted __be16" message when building with
make C=1 CF=-D__CHECK_ENDIAN__
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add support for the ISO/IEC 14443-B protocol and Type 4B tags.
It is expected that there will be only one tag within range so the full
anticollision scheme is not implemented. Only the SENSB_REQ/SENSB_RES
and ATTRIB_REQ/ATTRIB_RES are implemented.
CC: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
load_session allows a CLF to restore the gate <-> pipe table from some
proprietary location.
The main advantage to add this function is to reduce the memory wear by
running pipe creation (and storing) only once.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Extend it up to the maximum FWI value 4949 ms defined by the
ISO14443-3 specification.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Several spots in the kernel perform a sequence like:
skb_queue_tail(&sk->s_receive_queue, skb);
sk->sk_data_ready(sk, skb->len);
But at the moment we place the SKB onto the socket receive queue it
can be consumed and freed up. So this skb->len access is potentially
to freed up memory.
Furthermore, the skb->len can be modified by the consumer so it is
possible that the value isn't accurate.
And finally, no actual implementation of this callback actually uses
the length argument. And since nobody actually cared about it's
value, lots of call sites pass arbitrary values in such as '0' and
even '1'.
So just remove the length argument from the callback, that way there
is no confusion whatsoever and all of these use-after-free cases get
fixed as a side effect.
Based upon a patch by Eric Dumazet and his suggestion to audit this
issue tree-wide.
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the NFC pull request for 3.15. With this one we have:
- Support for ISO 15693 a.k.a. NFC vicinity a.k.a. Type 5 tags. ISO
15693 are long range (1 - 2 meters) vicinity tags/cards. The kernel
now supports those through the NFC netlink and digital APIs.
- Support for TI's trf7970a chipset. This chipset relies on the NFC
digital layer and the driver currently supports type 2, 4A and 5 tags.
- Support for NXP's pn544 secure firmare download. The pn544 C3 chipsets
relies on a different firmware download protocal than the C2 one. We
now support both and use the right one depending on the version we
detect at runtime.
- Support for 4A tags from the NFC digital layer.
- A bunch of cleanups and minor fixes from Axel Lin and Thierry Escande.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=xikL
-----END PGP SIGNATURE-----
Merge tag 'nfc-next-3.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/nfc-next
Samuel Ortiz <sameo@linux.intel.com> says:
"NFC: 3.15: First pull request
This is the NFC pull request for 3.15. With this one we have:
- Support for ISO 15693 a.k.a. NFC vicinity a.k.a. Type 5 tags. ISO
15693 are long range (1 - 2 meters) vicinity tags/cards. The kernel
now supports those through the NFC netlink and digital APIs.
- Support for TI's trf7970a chipset. This chipset relies on the NFC
digital layer and the driver currently supports type 2, 4A and 5 tags.
- Support for NXP's pn544 secure firmare download. The pn544 C3 chipsets
relies on a different firmware download protocal than the C2 one. We
now support both and use the right one depending on the version we
detect at runtime.
- Support for 4A tags from the NFC digital layer.
- A bunch of cleanups and minor fixes from Axel Lin and Thierry Escande."
Signed-off-by: John W. Linville <linville@tuxdriver.com>
nfc_llcp_find_local() does not modify any list entry while iterating the list.
So use list_for_each_entry instead of list_for_each_entry_safe.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This checking is common for all caller, so move the checking to one place.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Without this test, it returns NULL if dev->n_targets is 0 anyway.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
According to the latest draft specification from
the NFC-V committee, ISO/IEC 15693 tags will be
referred to as "Type 5" tags and not "Type V"
tags anymore. Make the code reflect the new
terminology.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This ensures we won't add polling function to the table of polling technologies
for non-supported protocols.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
nfc_find_se() does not modify any list entry while iterating the list.
So use list_for_each_entry instead of list_for_each_entry_safe.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Calling init_completion() once is enough.
Then use reinit_completion() instead in __nci_request() and nci_spi_send().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The check should be for setup function pointer.
This patch fixes NULL pointer dereference issue for NCI
based NFC driver which doesn't define setup handler.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This fixes a memory leak issue that may occur if data sending fails in
initiator mode. The data_exch structure was not released in case of
error.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
There was a missing break making the digital stack configured for
ISO1443 target instead of ISO15693.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When a type 4A target is activated, this change adds the ISO-DEP SoD
when sending frames and removes it when receiving responses. Chaining
is not supported so sent frames are rejected if they exceed remote FSC
bytes.
Signed-off-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This adds support for ATS request and response handling for type 4A tag
activation.
Signed-off-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add ISO/IEC 15693 support by having netlink push the
1-byte DSFID and 8-byte UID tag information upstream.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add support for ISO/IEC 15693 to the digital layer. The code
currently uses single-slot anticollision only since the digital
layer infrastructure only supports one tag per adapter (making
it pointless to do 16-slot anticollision).
The code uses two new framing types:
'NFC_DIGITAL_FRAMING_ISO15693_INVENTORY' and
'NFC_DIGITAL_FRAMING_ISO15693_TVT'. The former is used to
tell the driver to prepare for an Inventory command and the
ensuing anticollision sequence. The latter is used to tell
the driver that the anticollision sequence is over and to
prepare for non-inventory commands.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Pull networking updates from David Miller:
1) BPF debugger and asm tool by Daniel Borkmann.
2) Speed up create/bind in AF_PACKET, also from Daniel Borkmann.
3) Correct reciprocal_divide and update users, from Hannes Frederic
Sowa and Daniel Borkmann.
4) Currently we only have a "set" operation for the hw timestamp socket
ioctl, add a "get" operation to match. From Ben Hutchings.
5) Add better trace events for debugging driver datapath problems, also
from Ben Hutchings.
6) Implement auto corking in TCP, from Eric Dumazet. Basically, if we
have a small send and a previous packet is already in the qdisc or
device queue, defer until TX completion or we get more data.
7) Allow userspace to manage ipv6 temporary addresses, from Jiri Pirko.
8) Add a qdisc bypass option for AF_PACKET sockets, from Daniel
Borkmann.
9) Share IP header compression code between Bluetooth and IEEE802154
layers, from Jukka Rissanen.
10) Fix ipv6 router reachability probing, from Jiri Benc.
11) Allow packets to be captured on macvtap devices, from Vlad Yasevich.
12) Support tunneling in GRO layer, from Jerry Chu.
13) Allow bonding to be configured fully using netlink, from Scott
Feldman.
14) Allow AF_PACKET users to obtain the VLAN TPID, just like they can
already get the TCI. From Atzm Watanabe.
15) New "Heavy Hitter" qdisc, from Terry Lam.
16) Significantly improve the IPSEC support in pktgen, from Fan Du.
17) Allow ipv4 tunnels to cache routes, just like sockets. From Tom
Herbert.
18) Add Proportional Integral Enhanced packet scheduler, from Vijay
Subramanian.
19) Allow openvswitch to mmap'd netlink, from Thomas Graf.
20) Key TCP metrics blobs also by source address, not just destination
address. From Christoph Paasch.
21) Support 10G in generic phylib. From Andy Fleming.
22) Try to short-circuit GRO flow compares using device provided RX
hash, if provided. From Tom Herbert.
The wireless and netfilter folks have been busy little bees too.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2064 commits)
net/cxgb4: Fix referencing freed adapter
ipv6: reallocate addrconf router for ipv6 address when lo device up
fib_frontend: fix possible NULL pointer dereference
rtnetlink: remove IFLA_BOND_SLAVE definition
rtnetlink: remove check for fill_slave_info in rtnl_have_link_slave_info
qlcnic: update version to 5.3.55
qlcnic: Enhance logic to calculate msix vectors.
qlcnic: Refactor interrupt coalescing code for all adapters.
qlcnic: Update poll controller code path
qlcnic: Interrupt code cleanup
qlcnic: Enhance Tx timeout debugging.
qlcnic: Use bool for rx_mac_learn.
bonding: fix u64 division
rtnetlink: add missing IFLA_BOND_AD_INFO_UNSPEC
sfc: Use the correct maximum TX DMA ring size for SFC9100
Add Shradha Shah as the sfc driver maintainer.
net/vxlan: Share RX skb de-marking and checksum checks with ovs
tulip: cleanup by using ARRAY_SIZE()
ip_tunnel: clear IPCB in ip_tunnel_xmit() in case dst_link_failure() is called
net/cxgb4: Don't retrieve stats during recovery
...
Pull trivial tree updates from Jiri Kosina:
"Usual rocket science stuff from trivial.git"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
neighbour.h: fix comment
sched: Fix warning on make htmldocs caused by wait.h
slab: struct kmem_cache is protected by slab_mutex
doc: Fix typo in USB Gadget Documentation
of/Kconfig: Spelling s/one/once/
mkregtable: Fix sscanf handling
lp5523, lp8501: comment improvements
thermal: rcar: comment spelling
treewide: fix comments and printk msgs
IXP4xx: remove '1 &&' from a condition check in ixp4xx_restart()
Documentation: update /proc/uptime field description
Documentation: Fix size parameter for snprintf
arm: fix comment header and macro name
asm-generic: uaccess: Spelling s/a ny/any/
mtd: onenand: fix comment header
doc: driver-model/platform.txt: fix a typo
drivers: fix typo in DEVTMPFS_MOUNT Kconfig help text
doc: Fix typo (acces_process_vm -> access_process_vm)
treewide: Fix typos in printk
drivers/gpu/drm/qxl/Kconfig: reformat the help text
...
This is a follow-up patch to f3d3342602 ("net: rework recvmsg
handler msg_name and msg_namelen logic").
DECLARE_SOCKADDR validates that the structure we use for writing the
name information to is not larger than the buffer which is reserved
for msg->msg_name (which is 128 bytes). Also use DECLARE_SOCKADDR
consistently in sendmsg code paths.
Signed-off-by: Steffen Hurrle <steffen@hurrle.net>
Suggested-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch sets the correct rf tech value and crc functions in target
mode when receiving a PSL_REQ, as done when receiving an ATR_REQ.
Signed-off-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The curr_protocol field of nfc_digital_dev structure used to determine
if a target is currently active was set too soon, immediately when a
target is found. This is not good since there is no other way than
deactivate_target() to reset curr_protocol and if activate_target() is
not called, the target remains active and it's not possible to put the
device in poll mode anymore.
With this patch curr_protocol is set when nfc core activates a target,
puts a device up, or when an ATR_REQ is received in target mode.
Signed-off-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch fixed several typo in printk from various
part of kernel source.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This API can be used by drivers to send their custom
configuration using SET_CONFIG NCI command to the device.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Some drivers require special configuration while initializing.
This patch adds setup handler for this custom configuration.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Local general bytes returned by nfc_get_local_general_bytes()
are already in correct order. We don't need to reverse them.
Remove local_gb[] local array as it's not needed any more.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
nci_close_device() sends nci reset command to the device.
If there is no response for this command, nci request timeout
occurs first and then cmd timeout happens. Because command
timer has started after sending the command.
We are immediately flushing command workqueue after nci
timeout. Later we will try to schedule cmd_work in command
timer which leads to a crash.
Cancel cmd_timer before flushing the workqueue to fix the
problem.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This removes the declaration of NFCID3 size in digital_dep.c and now
uses the one from nfc.h.
This also removes a faulty and unneeded call to max().
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
It's bad to use these macros when not dealing with error code. this
patch changes calls to these macros with correct casts.
Signed-off-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
SE discovery errors are currently overwriting the dev_up() return error.
This is wrong for many reasons:
- We don't want to report an error if we actually brought the device up
but it failed to discover SEs. By doing so we pretend we don't have an
NFC functional device even we do. The only thing we could not do was
checking for SEs availability. This is the false negative case.
- In some cases the actual device power up failed but the SE discovery
succeeded. Userspace then believes the device is up while it's not.
This is the false positive case.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
If MIUX is not present in CONNECT or CC use default MIU value (128)
instead of one announced durring link setup.
This was affecting Bluetooth handover with Android 4.3+ NCI stack.
Signed-off-by: Szymon Janc <szymon.janc@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
If sending was not completed due to low memory condition msg_data
was not free before returning from function.
Signed-off-by: Szymon Janc <szymon.janc@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
If the device is polling, this will trigger a netlink event to notify
userspace about the polling error.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
With commit e29a9e2ae1, we set the active_target pointer from
nfc_dep_link_is_up() in order to support the case where the target
detection and the DEP link setting are done atomically by the driver.
That can only happen in initiator mode, so we need to check for that
otherwise we fail to bring a p2p link in target mode.
Signed-off-by: Arron Wang <arron.wang@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Correct spelling typo in various part of kernel
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Several files refer to an old address for the Free Software Foundation
in the file header comment. Resolve by replacing the address with
the URL <http://www.gnu.org/licenses/> so that we do not have to keep
updating the header comments anytime the address changes.
CC: linux-wireless@vger.kernel.org
CC: Lauro Ramos Venancio <lauro.venancio@openbossa.org>
CC: Aloisio Almeida Jr <aloisio.almeida@openbossa.org>
CC: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch now always passes msg->msg_namelen as 0. recvmsg handlers must
set msg_namelen to the proper size <= sizeof(struct sockaddr_storage)
to return msg_name to the user.
This prevents numerous uninitialized memory leaks we had in the
recvmsg handlers and makes it harder for new code to accidentally leak
uninitialized memory.
Optimize for the case recvfrom is called with NULL as address. We don't
need to copy the address at all, so set it to NULL before invoking the
recvmsg handler. We can do so, because all the recvmsg handlers must
cope with the case a plain read() is called on them. read() also sets
msg_name to NULL.
Also document these changes in include/linux/net.h as suggested by David
Miller.
Changes since RFC:
Set msg->msg_name = NULL if user specified a NULL in msg_name but had a
non-null msg_namelen in verify_iovec/verify_compat_iovec. This doesn't
affect sendto as it would bail out earlier while trying to copy-in the
address. It also more naturally reflects the logic by the callers of
verify_iovec.
With this change in place I could remove "
if (!uaddr || msg_sys->msg_namelen == 0)
msg->msg_name = NULL
".
This change does not alter the user visible error logic as we ignore
msg_namelen as long as msg_name is NULL.
Also remove two unnecessary curly brackets in ___sys_recvmsg and change
comments to netdev style.
Cc: David Miller <davem@davemloft.net>
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Register generic netlink multicast groups as an array with
the family and give them contiguous group IDs. Then instead
of passing the global group ID to the various functions that
send messages, pass the ID relative to the family - for most
families that's just 0 because the only have one group.
This avoids the list_head and ID in each group, adding a new
field for the mcast group ID offset to the family.
At the same time, this allows us to prevent abusing groups
again like the quota and dropmon code did, since we can now
check that a family only uses a group it owns.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This doesn't really change anything, but prepares for the
next patch that will change the APIs to pass the group ID
within the family, rather than the global group ID.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As suggested by David Miller, make genl_register_family_with_ops()
a macro and pass only the array, evaluating ARRAY_SIZE() in the
macro, this is a little safer.
The openvswitch has some indirection, assing ops/n_ops directly in
that code. This might ultimately just assign the pointers in the
family initializations, saving the struct genl_family_and_ops and
code (once mcast groups are handled differently.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that genl_ops are no longer modified in place when
registering, they can be made const. This patch was done
mostly with spatch:
@@
identifier ops;
@@
+const
struct genl_ops ops[] = {
...
};
(except the struct thing in net/openvswitch/datapath.c)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
se_io_cb can be declared static. This fixes the following sparse
warning:
net/nfc/netlink.c:1287:6: warning: symbol 'se_io_cb' was not declared.
Should it be static?
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The NFC Forum NCI specification defines both a hardware and software
protocol when using a SPI physical transport to connect an NFC NCI
Chipset. The hardware requirement is that, after having raised the chip
select line, the SPI driver must wait for an INT line from the NFC
chipset to raise before it sends the data. The chip select must be
raised first though, because this is the signal that the NFC chipset
will detect to wake up and then raise its INT line. If the INT line
doesn't raise in a timely fashion, the SPI driver should abort
operation.
When data is transferred from Device host (DH) to NFC Controller (NFCC),
the signaling sequence is the following:
Data Transfer from DH to NFCC
• 1-Master asserts SPI_CSN
• 2-Slave asserts SPI_INT
• 3-Master sends NCI-over-SPI protocol header and payload data
• 4-Slave deasserts SPI_INT
• 5-Master deasserts SPI_CSN
When data must be transferred from NFCC to DH, things are a little bit
different.
Data Transfer from NFCC to DH
• 1-Slave asserts SPI_INT -> NFC chipset irq handler called -> process
reading from SPI
• 2-Master asserts SPI_CSN
• 3-Master send 2-octet NCI-over-SPI protocol header
• 4-Slave sends 2-octet NCI-over-SPI protocol payload length
• 5-Slave sends NCI-over-SPI protocol payload
• 6-Master deasserts SPI_CSN
In this case, SPI driver should function normally as it does today. Note
that the INT line can and will be lowered anytime between beginning of
step 3 and end of step 5. A low INT is therefore valid after chip select
has been raised.
This would be easily implemented in a single driver. Unfortunately, we
don't write the SPI driver and I had to imagine some workaround trick to
get the SPI and NFC drivers to work in a synchronized fashion. The trick
is the following:
- send an empty spi message: this will raise the chip select line, and
send nothing. We expect the /CS line will stay arisen because we asked
for it in the spi_transfer cs_change field
- wait for a completion, that will be completed by the NFC driver IRQ
handler when it knows we are in the process of sending data (NFC spec
says that we use SPI in a half duplex mode, so we are either sending or
receiving).
- when completed, proceed with the normal data send.
This has been tested and verified to work very consistently on a Nexus
10 (spi-s3c64xx driver). It may not work the same with other spi
drivers.
The previously defined nci_spi_ops{} whose intended purpose were to
address this problem are not used anymore and therefore totally removed.
The nci_spi_send() takes a new optional write_handshake_completion
completion pointer. If non NULL, the nci spi layer will run the above
trick when sending data to the NFC Chip. If NULL, the data is sent
normally all at once and it is then the NFC driver responsibility to
know what it's doing.
Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Previously, nci_spi_recv_frame() would directly transmit incoming frames
to the NCI Core. However, it turns out that some NFC NCI Chips will add
additional proprietary headers that must be handled/removed before NCI
Core gets a chance to handle the frame. With this modification, the chip
phy or driver are now responsible to transmit incoming frames to NCI
Core after proper treatment, and NCI SPI becomes a driver helper instead
of sitting between the NFC driver and NCI Core.
As a general rule in NFC, *_recv_frame() APIs are used to deliver an
incoming frame to an upper layer. To better suit the actual purpose of
nci_spi_recv_frame(), and go along with its nci_spi_send()
counterpart, the function is renamed to nci_spi_read()
The skb is returned as the function result
Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Using ARM compiler, and without zero-ing spi_transfer, spi-s3c64xx
driver would issue abnormal errors due to bpw field value being set to
unexpected value. This structure MUST be set to all zeros except for
those field specifically used.
Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Implementation of the NFC_CMD_SE_IO command for sending ISO7816 APDUs to
NFC embedded secure elements. The reply is forwarded to user space
through NFC_CMD_SE_IO as well.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This was triggered by the following sparse warning:
net/nfc/digital_technology.c:272:20: sparse: cast to restricted __be16
The SENS_RES response must be treated as __le16 with the first byte
received as LSB and the second one as MSB. This is the way neard
handles it in the sens_res field of the nfc_target structure which is
treated as u16 in cpu endianness. So le16_to_cpu() is used on the
received SENS_RES instead of memcpy'ing it.
SENS_RES test macros have also been fixed accordingly.
Signed-off-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In the rawsock data exchange callback, the sk_buff is not freed
on error.
Signed-off-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Fixes sparse hint:
net/nfc/digital_technology.c:640:5: sparse: symbol 'digital_tg_send_sensf_res'
was not declared. Should it be static?
Cc: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
We do not add the newline to the pr_fmt macro, in order to give more
flexibility to the caller and to keep the logging style consistent with
the rest of the NFC and kernel code.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
They can be replaced by the standard pr_err and pr_debug one after
defining the right pr_fmt macro.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Storing the spi device was forgotten in the original implementation,
which would pretty obviously cause some kind of serious crash when
actually trying to send something through that device.
Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This adds support for NFC-DEP target mode for NFC-A and NFC-F
technologies.
If the driver provides it, the stack uses an automatic mode for
technology detection and automatic anti-collision. Otherwise the stack
tries to use non-automatic synchronization and listens for SENS_REQ and
SENSF_REQ commands.
The detection, activation, and data exchange procedures work exactly
the same way as in initiator mode, as described in the previous
commits, except that the digital stack waits for commands and sends
responses back to the peer device.
Signed-off-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This adds support for NFC-DEP protocol in initiator mode for NFC-A and
NFC-F technologies.
When a target is detected, the process flow is as follow:
For NFC-A technology:
1 - The digital stack receives a SEL_RES as the reply of the SEL_REQ
command.
2 - If b7 of SEL_RES is set, the peer device is configure for NFC-DEP
protocol. NFC core is notified through nfc_targets_found().
Execution continues at step 4.
3 - Otherwise, it's a tag and the NFC core is notified. Detection
ends.
4 - The digital stacks sends an ATR_REQ command containing a randomly
generated NFCID3 and the general bytes obtained from the LLCP layer
of NFC core.
For NFC-F technology:
1 - The digital stack receives a SENSF_RES as the reply of the
SENSF_REQ command.
2 - If B1 and B2 of NFCID2 are 0x01 and 0xFE respectively, the peer
device is configured for NFC-DEP protocol. NFC core is notified
through nfc_targets_found(). Execution continues at step 4.
3 - Otherwise it's a type 3 tag. NFC core is notified. Detection
ends.
4 - The digital stacks sends an ATR_REQ command containing the NFC-F
NFCID2 as NFCID3 and the general bytes obtained from the LLCP layer
of NFC core.
For both technologies:
5 - The digital stacks receives the ATR_RES response containing the
NFCID3 and the general bytes of the peer device.
6 - The digital stack notifies NFC core that the DEP link is up through
nfc_dep_link_up().
7 - The NFC core performs data exchange through tm_transceive().
8 - The digital stack sends a DEP_REQ command containing an I PDU with
the data from NFC core.
9 - The digital stack receives a DEP_RES command
10 - If the DEP_RES response contains a supervisor PDU with timeout
extension request (RTOX) the digital stack sends a DEP_REQ
command containing a supervisor PDU acknowledging the RTOX
request. The execution continues at step 9.
11 - If the DEP_RES response contains an I PDU, the response data is
passed back to NFC core through the response callback. The
execution continues at step 8.
Signed-off-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This adds polling support for NFC-F technology at 212 kbits/s and 424
kbits/s. A user space application like neard can send type 3 tag
commands through the NFC core.
Process flow for NFC-F detection is as follow:
1 - The digital stack sends the SENSF_REQ command to the NFC device.
2 - A peer device replies with a SENSF_RES response.
3 - The digital stack notifies the NFC core of the presence of a
target in the operation field and passes the target NFCID2.
This also adds support for CRC calculation of type CRC-F. The CRC
calculation is handled by the digital stack if the NFC device doesn't
support it.
Signed-off-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This adds support for NFC-A technology at 106 kbits/s. The stack can
detect tags of type 1 and 2. There is no support for collision
detection. Tags can be read and written by using a user space
application or a daemon like neard.
The flow of polling operations for NFC-A detection is as follow:
1 - The digital stack sends the SENS_REQ command to the NFC device.
2 - The NFC device receives a SENS_RES response from a peer device and
passes it to the digital stack.
3 - If the SENS_RES response identifies a type 1 tag, detection ends.
NFC core is notified through nfc_targets_found().
4 - Otherwise, the digital stack sets the cascade level of NFCID1 to
CL1 and sends the SDD_REQ command.
5 - The digital stack selects SEL_CMD and SEL_PAR according to the
cascade level and sends the SDD_REQ command.
4 - The digital stack receives a SDD_RES response for the cascade level
passed in the SDD_REQ command.
5 - The digital stack analyses (part of) NFCID1 and verify BCC.
6 - The digital stack sends the SEL_REQ command with the NFCID1
received in the SDD_RES.
6 - The peer device replies with a SEL_RES response
7 - Detection ends if NFCID1 is complete. NFC core notified of new
target by nfc_targets_found().
8 - If NFCID1 is not complete, the cascade level is incremented (up
to and including CL3) and the execution continues at step 5 to
get the remaining bytes of NFCID1.
Once target detection is done, type 1 and 2 tag commands must be
handled by a user space application (i.e neard) through the NFC core.
Responses for type 1 tag are returned directly to user space via NFC
core.
Responses of type 2 commands are handled differently. The digital stack
doesn't analyse the type of commands sent through im_transceive() and
must differentiate valid responses from error ones.
The response process flow is as follow:
1 - If the response length is 16 bytes, it is a valid response of a
READ command. the packet is returned to the NFC core through the
callback passed to im_transceive(). Processing stops.
2 - If the response is 1 byte long and is a ACK byte (0x0A), it is a
valid response of a WRITE command for example. First packet byte
is set to 0 for no-error and passed back to the NFC core.
Processing stops.
3 - Any other response is treated as an error and -EIO error code is
returned to the NFC core through the response callback.
Moreover, since the driver can't differentiate success response from a
NACK response, the digital stack has to handle CRC calculation.
Thus, this patch also adds support for CRC calculation. If the driver
doesn't handle it, the digital stack will calculate CRC and will add it
to sent frames. CRC will also be checked and removed from received
frames. Pointers to the correct CRC calculation functions are stored in
the digital stack device structure when a target is detected. This
avoids the need to check the current target type for every call to
im_transceive() and for every response received from a peer device.
Signed-off-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This implements the mechanism used to send commands to the driver in
initiator mode through in_send_cmd().
Commands are serialized and sent to the driver by using a work item
on the system workqueue. Responses are handled asynchronously by
another work item. Once the digital stack receives the response through
the command_complete callback, the next command is sent to the driver.
This also implements the polling mechanism. It's handled by a work item
cycling on all supported protocols. The start poll command for a given
protocol is sent to the driver using the mechanism described above.
The process continues until a peer is discovered or stop_poll is
called. This patch implements the poll function for NFC-A that sends a
SENS_REQ command and waits for the SENS_RES response.
Signed-off-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This is the initial commit of the NFC Digital Protocol stack
implementation.
It offers an interface for devices that don't have an embedded NFC
Digital protocol stack. The driver instantiates the digital stack by
calling nfc_digital_allocate_device(). Within the nfc_digital_ops
structure, the driver specifies a set of function pointers for driver
operations. These functions must be implemented by the driver and are:
in_configure_hw:
Hardware configuration for RF technology and communication framing in
initiator mode. This is a synchronous function.
in_send_cmd:
Initiator mode data exchange using RF technology and framing previously
set with in_configure_hw. The peer response is returned through
callback cb. If an io error occurs or the peer didn't reply within the
specified timeout (ms), the error code is passed back through the resp
pointer. This is an asynchronous function.
tg_configure_hw:
Hardware configuration for RF technology and communication framing in
target mode. This is a synchronous function.
tg_send_cmd:
Target mode data exchange using RF technology and framing previously
set with tg_configure_hw. The peer next command is returned through
callback cb. If an io error occurs or the peer didn't reply within the
specified timeout (ms), the error code is passed back through the resp
pointer. This is an asynchronous function.
tg_listen:
Put the device in listen mode waiting for data from the peer device.
This is an asynchronous function.
tg_listen_mdaa:
If supported, put the device in automatic listen mode with mode
detection and automatic anti-collision. In this mode, the device
automatically detects the RF technology and executes the
anti-collision detection using the command responses specified in
mdaa_params. The mdaa_params structure contains SENS_RES, NFCID1, and
SEL_RES for 106A RF tech. NFCID2 and system code (sc) for 212F and
424F. The driver returns the NFC-DEP ATR_REQ command through cb. The
digital stack deducts the RF tech by analyzing the SoD of the frame
containing the ATR_REQ command. This is an asynchronous function.
switch_rf:
Turns device radio on or off. The stack does not call explicitly
switch_rf to turn the radio on. A call to in|tg_configure_hw must turn
the device radio on.
abort_cmd:
Discard the last sent command.
Then the driver registers itself against the digital stack by using
nfc_digital_register_device() which in turn registers the digital stack
against the NFC core layer. The digital stack implements common NFC
operations like dev_up(), dev_down(), start_poll(), stop_poll(), etc.
This patch is only a skeleton and NFC operations are just stubs.
Signed-off-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
