According to Timur Tabi
This bug in older U-Boots is definitely PowerPC-specific
So before allowing this driver to be built for platforms other than
PPC32, make sure that we don't accept malformed device trees on those
other platforms.
Suggested-by: Timur Tabi <timur@kernel.org>
Reviewed-by: Timur Tabi <timur@kernel.org>
Acked-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
For this to work correctly on little-endian hosts, don't access the
device-tree properties directly in native endianness, but use the
of_property_read_u32() helper.
Reviewed-by: Timur Tabi <timur@kernel.org>
Acked-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
The Soft UART hack is only needed for some PPC-based SOCs. To allow
building this driver for non-PPC, guard soft_uart_init() and its
helpers by CONFIG_PPC32, and use a no-op soft_uart_init() otherwise.
Reviewed-by: Timur Tabi <timur@kernel.org>
Acked-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
The "soft uart" mechanism is a workaround for a silicon bug which (as
far as I know) only affects some PPC-based SOCs.
The code that determines which microcode blob to request relies on
some powerpc-specific bits (e.g. the mfspr(SPRN_SVR) and hence also
the asm/reg.h header). This makes it a little awkward to allow this
driver to be built for non-PPC based SOCs with a QE, even if they are
not affected by that silicon bug and thus don't need any of the Soft
UART logic.
There's no way around guarding those bits with some ifdeffery, so to
keep that isolated, factor out the
do-we-need-soft-uart-and-if-so-handle-the-firmware to a separate
function, which we can then easily stub out for non-PPC.
Reviewed-by: Timur Tabi <timur@kernel.org>
Acked-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Some ARM-based SOCs (e.g. LS1021A) also have a QUICC engine. As
preparation for allowing this driver to build on ARM, replace the
ppc-specific in_be16() etc. by the qe_io* helpers. Done via
coccinelle.
Reviewed-by: Timur Tabi <timur@kernel.org>
Acked-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
This driver uses #defines from soc/fsl/cpm.h, so instead of relying on
some other header pulling that in, do that explicitly. This is
preparation for allowing this driver to build on ARM.
Reviewed-by: Timur Tabi <timur@kernel.org>
Acked-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Here is the "big" tty and serial driver patches for 5.5-rc1. It's a bit
later in the merge window than normal as I wanted to make sure some
last-minute patches applied to it were all sane. They seem to be :)
There's a lot of little stuff in here, for the tty core, and for lots of
serial drivers:
- reverts of uartlite serial driver patches that were wrong
- msm-serial driver fixes
- serial core updates and fixes
- tty core fixes
- serial driver dma mapping api changes
- lots of other tiny fixes and updates for serial drivers
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXebFIQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylnmACgjfMcfQWa7uC9Q6m2DaQaRMaW6QoAnjg+TgBB
eW9EhvyXL2VbrsuUl+iH
=Am9O
-----END PGP SIGNATURE-----
Merge tag 'tty-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial updates from Greg KH:
"Here is the "big" tty and serial driver patches for 5.5-rc1.
It's a bit later in the merge window than normal as I wanted to make
sure some last-minute patches applied to it were all sane. They seem
to be :)
There's a lot of little stuff in here, for the tty core, and for lots
of serial drivers:
- reverts of uartlite serial driver patches that were wrong
- msm-serial driver fixes
- serial core updates and fixes
- tty core fixes
- serial driver dma mapping api changes
- lots of other tiny fixes and updates for serial drivers
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (58 commits)
Revert "serial/8250: Add support for NI-Serial PXI/PXIe+485 devices"
vcs: prevent write access to vcsu devices
tty: vt: keyboard: reject invalid keycodes
tty: don't crash in tty_init_dev when missing tty_port
serial: stm32: fix clearing interrupt error flags
tty: Fix Kconfig indentation, continued
serial: serial_core: Perform NULL checks for break_ctl ops
tty: remove unused argument from tty_open_by_driver()
tty: Fix Kconfig indentation
{tty: serial, nand: onenand}: samsung: rename to fix build warning
serial: ifx6x60: add missed pm_runtime_disable
serial: pl011: Fix DMA ->flush_buffer()
Revert "serial-uartlite: Move the uart register"
Revert "serial-uartlite: Add get serial id if not provided"
Revert "serial-uartlite: Do not use static struct uart_driver out of probe()"
Revert "serial-uartlite: Add runtime support"
Revert "serial-uartlite: Change logic how console_port is setup"
Revert "serial-uartlite: Use allocated structure instead of static ones"
tty: serial: msm_serial: Use dma_request_chan() directly for channel request
tty: serial: tegra: Use dma_request_chan() directly for channel request
...
-----BEGIN PGP SIGNATURE-----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=uUXw
-----END PGP SIGNATURE-----
Merge tag 'pci-v5.5-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"Enumeration:
- Warn if a host bridge has no NUMA info (Yunsheng Lin)
- Add PCI_STD_NUM_BARS for the number of standard BARs (Denis
Efremov)
Resource management:
- Fix boot-time Embedded Controller GPE storm caused by incorrect
resource assignment after ACPI Bus Check Notification (Mika
Westerberg)
- Protect pci_reassign_bridge_resources() against concurrent
addition/removal (Benjamin Herrenschmidt)
- Fix bridge dma_ranges resource list cleanup (Rob Herring)
- Add "pci=hpmmiosize" and "pci=hpmmioprefsize" parameters to control
the MMIO and prefetchable MMIO window sizes of hotplug bridges
independently (Nicholas Johnson)
- Fix MMIO/MMIO_PREF window assignment that assigned more space than
desired (Nicholas Johnson)
- Only enforce bus numbers from bridge EA if the bridge has EA
devices downstream (Subbaraya Sundeep)
- Consolidate DT "dma-ranges" parsing and convert all host drivers to
use shared parsing (Rob Herring)
Error reporting:
- Restore AER capability after resume (Mayurkumar Patel)
- Add PoisonTLPBlocked AER counter (Rajat Jain)
- Use for_each_set_bit() to simplify AER code (Andy Shevchenko)
- Fix AER kernel-doc (Andy Shevchenko)
- Add "pcie_ports=dpc-native" parameter to allow native use of DPC
even if platform didn't grant control over AER (Olof Johansson)
Hotplug:
- Avoid returning prematurely from sysfs requests to enable or
disable a PCIe hotplug slot (Lukas Wunner)
- Don't disable interrupts twice when suspending hotplug ports (Mika
Westerberg)
- Fix deadlocks when PCIe ports are hot-removed while suspended (Mika
Westerberg)
Power management:
- Remove unnecessary ASPM locking (Bjorn Helgaas)
- Add support for disabling L1 PM Substates (Heiner Kallweit)
- Allow re-enabling Clock PM after it has been disabled (Heiner
Kallweit)
- Add sysfs attributes for controlling ASPM link states (Heiner
Kallweit)
- Remove CONFIG_PCIEASPM_DEBUG, including "link_state" and "clk_ctl"
sysfs files (Heiner Kallweit)
- Avoid AMD FCH XHCI USB PME# from D0 defect that prevents wakeup on
USB 2.0 or 1.1 connect events (Kai-Heng Feng)
- Move power state check out of pci_msi_supported() (Bjorn Helgaas)
- Fix incorrect MSI-X masking on resume and revert related nvme quirk
for Kingston NVME SSD running FW E8FK11.T (Jian-Hong Pan)
- Always return devices to D0 when thawing to fix hibernation with
drivers like mlx4 that used legacy power management (previously we
only did it for drivers with new power management ops) (Dexuan Cui)
- Clear PCIe PME Status even for legacy power management (Bjorn
Helgaas)
- Fix PCI PM documentation errors (Bjorn Helgaas)
- Use dev_printk() for more power management messages (Bjorn Helgaas)
- Apply D2 delay as milliseconds, not microseconds (Bjorn Helgaas)
- Convert xen-platform from legacy to generic power management (Bjorn
Helgaas)
- Removed unused .resume_early() and .suspend_late() legacy power
management hooks (Bjorn Helgaas)
- Rearrange power management code for clarity (Rafael J. Wysocki)
- Decode power states more clearly ("4" or "D4" really refers to
"D3cold") (Bjorn Helgaas)
- Notice when reading PM Control register returns an error (~0)
instead of interpreting it as being in D3hot (Bjorn Helgaas)
- Add missing link delays required by the PCIe spec (Mika Westerberg)
Virtualization:
- Move pci_prg_resp_pasid_required() to CONFIG_PCI_PRI (Bjorn
Helgaas)
- Allow VFs to use PRI (the PF PRI is shared by the VFs, but the code
previously didn't recognize that) (Kuppuswamy Sathyanarayanan)
- Allow VFs to use PASID (the PF PASID capability is shared by the
VFs, but the code previously didn't recognize that) (Kuppuswamy
Sathyanarayanan)
- Disconnect PF and VF ATS enablement, since ATS in PFs and
associated VFs can be enabled independently (Kuppuswamy
Sathyanarayanan)
- Cache PRI and PASID capability offsets (Kuppuswamy Sathyanarayanan)
- Cache the PRI PRG Response PASID Required bit (Bjorn Helgaas)
- Consolidate ATS declarations in linux/pci-ats.h (Krzysztof
Wilczynski)
- Remove unused PRI and PASID stubs (Bjorn Helgaas)
- Removed unnecessary EXPORT_SYMBOL_GPL() from ATS, PRI, and PASID
interfaces that are only used by built-in IOMMU drivers (Bjorn
Helgaas)
- Hide PRI and PASID state restoration functions used only inside the
PCI core (Bjorn Helgaas)
- Add a DMA alias quirk for the Intel VCA NTB (Slawomir Pawlowski)
- Serialize sysfs sriov_numvfs reads vs writes (Pierre Crégut)
- Update Cavium ACS quirk for ThunderX2 and ThunderX3 (George
Cherian)
- Fix the UPDCR register address in the Intel ACS quirk (Steffen
Liebergeld)
- Unify ACS quirk implementations (Bjorn Helgaas)
Amlogic Meson host bridge driver:
- Fix meson PERST# GPIO polarity problem (Remi Pommarel)
- Add DT bindings for Amlogic Meson G12A (Neil Armstrong)
- Fix meson clock names to match DT bindings (Neil Armstrong)
- Add meson support for Amlogic G12A SoC with separate shared PHY
(Neil Armstrong)
- Add meson extended PCIe PHY functions for Amlogic G12A USB3+PCIe
combo PHY (Neil Armstrong)
- Add arm64 DT for Amlogic G12A PCIe controller node (Neil Armstrong)
- Add commented-out description of VIM3 USB3/PCIe mux in arm64 DT
(Neil Armstrong)
Broadcom iProc host bridge driver:
- Invalidate iProc PAXB address mapping before programming it
(Abhishek Shah)
- Fix iproc-msi and mvebu __iomem annotations (Ben Dooks)
Cadence host bridge driver:
- Refactor Cadence PCIe host controller to use as a library for both
host and endpoint (Tom Joseph)
Freescale Layerscape host bridge driver:
- Add layerscape LS1028a support (Xiaowei Bao)
Intel VMD host bridge driver:
- Add VMD bus 224-255 restriction decode (Jon Derrick)
- Add VMD 8086:9A0B device ID (Jon Derrick)
- Remove Keith from VMD maintainer list (Keith Busch)
Marvell ARMADA 3700 / Aardvark host bridge driver:
- Use LTSSM state to build link training flag since Aardvark doesn't
implement the Link Training bit (Remi Pommarel)
- Delay before training Aardvark link in case PERST# was asserted
before the driver probe (Remi Pommarel)
- Fix Aardvark issues with Root Control reads and writes (Remi
Pommarel)
- Don't rely on jiffies in Aardvark config access path since
interrupts may be disabled (Remi Pommarel)
- Fix Aardvark big-endian support (Grzegorz Jaszczyk)
Marvell ARMADA 370 / XP host bridge driver:
- Make mvebu_pci_bridge_emul_ops static (Ben Dooks)
Microsoft Hyper-V host bridge driver:
- Add hibernation support for Hyper-V virtual PCI devices (Dexuan
Cui)
- Track Hyper-V pci_protocol_version per-hbus, not globally (Dexuan
Cui)
- Avoid kmemleak false positive on hv hbus buffer (Dexuan Cui)
Mobiveil host bridge driver:
- Change mobiveil csr_read()/write() function names that conflict
with riscv arch functions (Kefeng Wang)
NVIDIA Tegra host bridge driver:
- Fix Tegra CLKREQ dependency programming (Vidya Sagar)
Renesas R-Car host bridge driver:
- Remove unnecessary header include from rcar (Andrew Murray)
- Tighten register index checking for rcar inbound range programming
(Marek Vasut)
- Fix rcar inbound range alignment calculation to improve packing of
multiple entries (Marek Vasut)
- Update rcar MACCTLR setting to match documentation (Yoshihiro
Shimoda)
- Clear bit 0 of MACCTLR before PCIETCTLR.CFINIT per manual
(Yoshihiro Shimoda)
- Add Marek Vasut and Yoshihiro Shimoda as R-Car maintainers (Simon
Horman)
Rockchip host bridge driver:
- Make rockchip 0V9 and 1V8 power regulators non-optional (Robin
Murphy)
Socionext UniPhier host bridge driver:
- Set uniphier to host (RC) mode always (Kunihiko Hayashi)
Endpoint drivers:
- Fix endpoint driver sign extension problem when shifting page
number to phys_addr_t (Alan Mikhak)
Misc:
- Add NumaChip SPDX header (Krzysztof Wilczynski)
- Replace EXTRA_CFLAGS with ccflags-y (Krzysztof Wilczynski)
- Remove unused includes (Krzysztof Wilczynski)
- Removed unused sysfs attribute groups (Ben Dooks)
- Remove PTM and ASPM dependencies on PCIEPORTBUS (Bjorn Helgaas)
- Add PCIe Link Control 2 register field definitions to replace magic
numbers in AMDGPU and Radeon CIK/SI (Bjorn Helgaas)
- Fix incorrect Link Control 2 Transmit Margin usage in AMDGPU and
Radeon CIK/SI PCIe Gen3 link training (Bjorn Helgaas)
- Use pcie_capability_read_word() instead of pci_read_config_word()
in AMDGPU and Radeon CIK/SI (Frederick Lawler)
- Remove unused pci_irq_get_node() Greg Kroah-Hartman)
- Make asm/msi.h mandatory and simplify PCI_MSI_IRQ_DOMAIN Kconfig
(Palmer Dabbelt, Michal Simek)
- Read all 64 bits of Switchtec part_event_bitmap (Logan Gunthorpe)
- Fix erroneous intel-iommu dependency on CONFIG_AMD_IOMMU (Bjorn
Helgaas)
- Fix bridge emulation big-endian support (Grzegorz Jaszczyk)
- Fix dwc find_next_bit() usage (Niklas Cassel)
- Fix pcitest.c fd leak (Hewenliang)
- Fix typos and comments (Bjorn Helgaas)
- Fix Kconfig whitespace errors (Krzysztof Kozlowski)"
* tag 'pci-v5.5-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (160 commits)
PCI: Remove PCI_MSI_IRQ_DOMAIN architecture whitelist
asm-generic: Make msi.h a mandatory include/asm header
Revert "nvme: Add quirk for Kingston NVME SSD running FW E8FK11.T"
PCI/MSI: Fix incorrect MSI-X masking on resume
PCI/MSI: Move power state check out of pci_msi_supported()
PCI/MSI: Remove unused pci_irq_get_node()
PCI: hv: Avoid a kmemleak false positive caused by the hbus buffer
PCI: hv: Change pci_protocol_version to per-hbus
PCI: hv: Add hibernation support
PCI: hv: Reorganize the code in preparation of hibernation
MAINTAINERS: Remove Keith from VMD maintainer
PCI/ASPM: Remove PCIEASPM_DEBUG Kconfig option and related code
PCI/ASPM: Add sysfs attributes for controlling ASPM link states
PCI: Fix indentation
drm/radeon: Prefer pcie_capability_read_word()
drm/radeon: Replace numbers with PCI_EXP_LNKCTL2 definitions
drm/radeon: Correct Transmit Margin masks
drm/amdgpu: Prefer pcie_capability_read_word()
PCI: uniphier: Set mode register to host mode
drm/amdgpu: Replace numbers with PCI_EXP_LNKCTL2 definitions
...
As part of the cleanup of some remaining y2038 issues, I came to
fs/compat_ioctl.c, which still has a couple of commands that need support
for time64_t.
In completely unrelated work, I spent time on cleaning up parts of this
file in the past, moving things out into drivers instead.
After Al Viro reviewed an earlier version of this series and did a lot
more of that cleanup, I decided to try to completely eliminate the rest
of it and move it all into drivers.
This series incorporates some of Al's work and many patches of my own,
but in the end stops short of actually removing the last part, which is
the scsi ioctl handlers. I have patches for those as well, but they need
more testing or possibly a rewrite.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=lgCl
-----END PGP SIGNATURE-----
Merge tag 'compat-ioctl-5.5' of git://git.kernel.org:/pub/scm/linux/kernel/git/arnd/playground
Pull removal of most of fs/compat_ioctl.c from Arnd Bergmann:
"As part of the cleanup of some remaining y2038 issues, I came to
fs/compat_ioctl.c, which still has a couple of commands that need
support for time64_t.
In completely unrelated work, I spent time on cleaning up parts of
this file in the past, moving things out into drivers instead.
After Al Viro reviewed an earlier version of this series and did a lot
more of that cleanup, I decided to try to completely eliminate the
rest of it and move it all into drivers.
This series incorporates some of Al's work and many patches of my own,
but in the end stops short of actually removing the last part, which
is the scsi ioctl handlers. I have patches for those as well, but they
need more testing or possibly a rewrite"
* tag 'compat-ioctl-5.5' of git://git.kernel.org:/pub/scm/linux/kernel/git/arnd/playground: (42 commits)
scsi: sd: enable compat ioctls for sed-opal
pktcdvd: add compat_ioctl handler
compat_ioctl: move SG_GET_REQUEST_TABLE handling
compat_ioctl: ppp: move simple commands into ppp_generic.c
compat_ioctl: handle PPPIOCGIDLE for 64-bit time_t
compat_ioctl: move PPPIOCSCOMPRESS to ppp_generic
compat_ioctl: unify copy-in of ppp filters
tty: handle compat PPP ioctls
compat_ioctl: move SIOCOUTQ out of compat_ioctl.c
compat_ioctl: handle SIOCOUTQNSD
af_unix: add compat_ioctl support
compat_ioctl: reimplement SG_IO handling
compat_ioctl: move WDIOC handling into wdt drivers
fs: compat_ioctl: move FITRIM emulation into file systems
gfs2: add compat_ioctl support
compat_ioctl: remove unused convert_in_user macro
compat_ioctl: remove last RAID handling code
compat_ioctl: remove /dev/raw ioctl translation
compat_ioctl: remove PCI ioctl translation
compat_ioctl: remove joystick ioctl translation
...
- Protect pci_reassign_bridge_resources() against concurrent
addition/removal (Benjamin Herrenschmidt)
- Fix bridge dma_ranges resource list cleanup (Rob Herring)
- Add PCI_STD_NUM_BARS for the number of standard BARs (Denis Efremov)
- Add "pci=hpmmiosize" and "pci=hpmmioprefsize" parameters to control the
MMIO and prefetchable MMIO window sizes of hotplug bridges
independently (Nicholas Johnson)
- Fix MMIO/MMIO_PREF window assignment that assigned more space than
desired (Nicholas Johnson)
- Only enforce bus numbers from bridge EA if the bridge has EA devices
downstream (Subbaraya Sundeep)
* pci/resource:
PCI: Do not use bus number zero from EA capability
PCI: Avoid double hpmemsize MMIO window assignment
PCI: Add "pci=hpmmiosize" and "pci=hpmmioprefsize" parameters
PCI: Add PCI_STD_NUM_BARS for the number of standard BARs
PCI: Fix missing bridge dma_ranges resource list cleanup
PCI: Protect pci_reassign_bridge_resources() against concurrent addition/removal
New features:
- SECCOMP support
- nommu support
- SBI-less system support
- M-Mode support
- TLB flush optimizations
Other improvements:
- Pass the complete RISC-V ISA string supported by the CPU cores to
userspace, rather than redacting parts of it in the kernel
- Add platform DMA IP block data to the HiFive Unleashed board DT file
- Add Makefile support for BZ2, LZ4, LZMA, LZO kernel image
compression formats, in line with other architectures
Cleanups:
- Remove unnecessary PTE_PARENT_SIZE macro
- Standardize include guard naming across arch/riscv
-----BEGIN PGP SIGNATURE-----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=nbwY
-----END PGP SIGNATURE-----
Merge tag 'riscv/for-v5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V updates from Paul Walmsley:
"New features:
- SECCOMP support
- nommu support
- SBI-less system support
- M-Mode support
- TLB flush optimizations
Other improvements:
- Pass the complete RISC-V ISA string supported by the CPU cores to
userspace, rather than redacting parts of it in the kernel
- Add platform DMA IP block data to the HiFive Unleashed board DT
file
- Add Makefile support for BZ2, LZ4, LZMA, LZO kernel image
compression formats, in line with other architectures
Cleanups:
- Remove unnecessary PTE_PARENT_SIZE macro
- Standardize include guard naming across arch/riscv"
* tag 'riscv/for-v5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux: (22 commits)
riscv: provide a flat image loader
riscv: add nommu support
riscv: clear the instruction cache and all registers when booting
riscv: read the hart ID from mhartid on boot
riscv: provide native clint access for M-mode
riscv: dts: add support for PDMA device of HiFive Unleashed Rev A00
riscv: add support for MMIO access to the timer registers
riscv: implement remote sfence.i using IPIs
riscv: cleanup the default power off implementation
riscv: poison SBI calls for M-mode
riscv: don't allow selecting SBI based drivers for M-mode
RISC-V: Add multiple compression image format.
riscv: clean up the macro format in each header file
riscv: Use PMD_SIZE to replace PTE_PARENT_SIZE
riscv: abstract out CSR names for supervisor vs machine mode
riscv: separate MMIO functions into their own header file
riscv: enter WFI in default_power_off() if SBI does not shutdown
RISC-V: Issue a tlb page flush if possible
RISC-V: Issue a local tlbflush if possible.
RISC-V: Do not invoke SBI call if cpumask is empty
...
Here is the "big" set of driver core patches for 5.5-rc1
There's a few minor cleanups and fixes in here, but the majority of the
patches in here fall into two buckets:
- debugfs api cleanups and fixes
- driver core device link support for boot dependancy issues
The debugfs api cleanups are working to slowly refactor the debugfs apis
so that it is even harder to use incorrectly. That work has been
happening for the past few kernel releases and will continue over time,
it's a long-term project/goal
The driver core device link support missed 5.4 by just a bit, so it's
been sitting and baking for many months now. It's from Saravana Kannan
to help resolve the problems that DT-based systems have at boot time
with dependancy graphs and kernel modules. Turns out that no one has
actually tried to build a generic arm64 kernel with loads of modules and
have it "just work" for a variety of platforms (like a distro kernel)
The big problem turned out to be a lack of depandancy information
between different areas of DT entries, and the work here resolves that
problem and now allows devices to boot properly, and quicker than a
monolith kernel.
All of these patches have been in linux-next for a long time with no
reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXd6m6Q8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yntJQCcCqg6RQ7LTdHuZv1ETeefXlsfk00An1Jtean6
42bWGx52bGFvAcpjWy8R
=P7hq
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the "big" set of driver core patches for 5.5-rc1
There's a few minor cleanups and fixes in here, but the majority of
the patches in here fall into two buckets:
- debugfs api cleanups and fixes
- driver core device link support for boot dependancy issues
The debugfs api cleanups are working to slowly refactor the debugfs
apis so that it is even harder to use incorrectly. That work has been
happening for the past few kernel releases and will continue over
time, it's a long-term project/goal
The driver core device link support missed 5.4 by just a bit, so it's
been sitting and baking for many months now. It's from Saravana Kannan
to help resolve the problems that DT-based systems have at boot time
with dependancy graphs and kernel modules. Turns out that no one has
actually tried to build a generic arm64 kernel with loads of modules
and have it "just work" for a variety of platforms (like a distro
kernel). The big problem turned out to be a lack of dependency
information between different areas of DT entries, and the work here
resolves that problem and now allows devices to boot properly, and
quicker than a monolith kernel.
All of these patches have been in linux-next for a long time with no
reported issues"
* tag 'driver-core-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (68 commits)
tracing: Remove unnecessary DEBUG_FS dependency
of: property: Add device link support for interrupt-parent, dmas and -gpio(s)
debugfs: Fix !DEBUG_FS debugfs_create_automount
of: property: Add device link support for "iommu-map"
of: property: Fix the semantics of of_is_ancestor_of()
i2c: of: Populate fwnode in of_i2c_get_board_info()
drivers: base: Fix Kconfig indentation
firmware_loader: Fix labels with comma for builtin firmware
driver core: Allow device link operations inside sync_state()
driver core: platform: Declare ret variable only once
cpu-topology: declare parse_acpi_topology in <linux/arch_topology.h>
crypto: hisilicon: no need to check return value of debugfs_create functions
driver core: platform: use the correct callback type for bus_find_device
firmware_class: make firmware caching configurable
driver core: Clarify documentation for fwnode_operations.add_links()
mailbox: tegra: Fix superfluous IRQ error message
net: caif: Fix debugfs on 64-bit platforms
mac80211: Use debugfs_create_xul() helper
media: c8sectpfe: no need to check return value of debugfs_create functions
of: property: Add device link support for iommus, mboxes and io-channels
...
Here is the big set of char/misc and other driver patches for 5.5-rc1
Loads of different things in here, this feels like the catch-all of
driver subsystems these days. Full details are in the shortlog, but
nothing major overall, just lots of driver updates and additions.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXd6ewA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymNXACfebVkDrFOH9EqDgFArPvZ1i9EmZ4AoLbE1Wki
ftJApk+Ov1BT2TvClOza
=cXqg
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the big set of char/misc and other driver patches for 5.5-rc1
Loads of different things in here, this feels like the catch-all of
driver subsystems these days. Full details are in the shortlog, but
nothing major overall, just lots of driver updates and additions.
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (198 commits)
char: Fix Kconfig indentation, continued
habanalabs: add more protection of device during reset
habanalabs: flush EQ workers in hard reset
habanalabs: make the reset code more consistent
habanalabs: expose reset counters via existing INFO IOCTL
habanalabs: make code more concise
habanalabs: use defines for F/W files
habanalabs: remove prints on successful device initialization
habanalabs: remove unnecessary checks
habanalabs: invalidate MMU cache only once
habanalabs: skip VA block list update in reset flow
habanalabs: optimize MMU unmap
habanalabs: prevent read/write from/to the device during hard reset
habanalabs: split MMU properties to PCI/DRAM
habanalabs: re-factor MMU masks and documentation
habanalabs: type specific MMU cache invalidation
habanalabs: re-factor memory module code
habanalabs: export uapi defines to user-space
habanalabs: don't print error when queues are full
habanalabs: increase max jobs number to 512
...
This reverts commit fdc2de8712 ("serial/8250:
Add support for NI-Serial PXI/PXIe+485 devices").
The commit fdc2de8712 ("serial/8250: Add support for NI-Serial
PXI/PXIe+485 devices") introduced a breakage on NI-Serial PXI(e)-RS485
devices, RS-232 variants have no issue. The Linux system can enumerate the
NI-Serial PXI(e)-RS485 devices, but it broke the R/W operation on the
ports.
However, the implementation is working on the NI internal Linux RT kernel
but it does not work in the Linux main tree kernel. This is only affecting
NI products, specifically the RS-485 variants. Reverting the upstream
until a proper implementation that can apply to both NI internal Linux
kernel and Linux mainline kernel is figured out.
Signed-off-by: Je Yen Tam <je.yen.tam@ni.com>
Fixes: fdc2de8712 ("serial/8250: Add support for NI-Serial PXI/PXIe+485 devices")
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191127075301.9866-1-je.yen.tam@ni.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit d21b0be246 ("vt: introduce unicode mode for /dev/vcs") guarded
against using devices containing attributes as this is not yet
implemented. It however failed to guard against writes to any devices
as this is also unimplemented.
Reported-by: Or Cohen <orcohen@paloaltonetworks.com>
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
Cc: <stable@vger.kernel.org> # v4.19+
Cc: Jiri Slaby <jslaby@suse.com>
Fixes: d21b0be246 ("vt: introduce unicode mode for /dev/vcs")
Link: https://lore.kernel.org/r/nycvar.YSQ.7.76.1911051030580.30289@knanqh.ubzr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull locking updates from Ingo Molnar:
"The main changes in this cycle were:
- A comprehensive rewrite of the robust/PI futex code's exit handling
to fix various exit races. (Thomas Gleixner et al)
- Rework the generic REFCOUNT_FULL implementation using
atomic_fetch_* operations so that the performance impact of the
cmpxchg() loops is mitigated for common refcount operations.
With these performance improvements the generic implementation of
refcount_t should be good enough for everybody - and this got
confirmed by performance testing, so remove ARCH_HAS_REFCOUNT and
REFCOUNT_FULL entirely, leaving the generic implementation enabled
unconditionally. (Will Deacon)
- Other misc changes, fixes, cleanups"
* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (27 commits)
lkdtm: Remove references to CONFIG_REFCOUNT_FULL
locking/refcount: Remove unused 'refcount_error_report()' function
locking/refcount: Consolidate implementations of refcount_t
locking/refcount: Consolidate REFCOUNT_{MAX,SATURATED} definitions
locking/refcount: Move saturation warnings out of line
locking/refcount: Improve performance of generic REFCOUNT_FULL code
locking/refcount: Move the bulk of the REFCOUNT_FULL implementation into the <linux/refcount.h> header
locking/refcount: Remove unused refcount_*_checked() variants
locking/refcount: Ensure integer operands are treated as signed
locking/refcount: Define constants for saturation and max refcount values
futex: Prevent exit livelock
futex: Provide distinct return value when owner is exiting
futex: Add mutex around futex exit
futex: Provide state handling for exec() as well
futex: Sanitize exit state handling
futex: Mark the begin of futex exit explicitly
futex: Set task::futex_state to DEAD right after handling futex exit
futex: Split futex_mm_release() for exit/exec
exit/exec: Seperate mm_release()
futex: Replace PF_EXITPIDONE with a state
...
Do not try to handle keycodes that are too big, otherwise we risk doing
out-of-bounds writes:
BUG: KASAN: global-out-of-bounds in clear_bit include/asm-generic/bitops-instrumented.h:56 [inline]
BUG: KASAN: global-out-of-bounds in kbd_keycode drivers/tty/vt/keyboard.c:1411 [inline]
BUG: KASAN: global-out-of-bounds in kbd_event+0xe6b/0x3790 drivers/tty/vt/keyboard.c:1495
Write of size 8 at addr ffffffff89a1b2d8 by task syz-executor108/1722
...
kbd_keycode drivers/tty/vt/keyboard.c:1411 [inline]
kbd_event+0xe6b/0x3790 drivers/tty/vt/keyboard.c:1495
input_to_handler+0x3b6/0x4c0 drivers/input/input.c:118
input_pass_values.part.0+0x2e3/0x720 drivers/input/input.c:145
input_pass_values drivers/input/input.c:949 [inline]
input_set_keycode+0x290/0x320 drivers/input/input.c:954
evdev_handle_set_keycode_v2+0xc4/0x120 drivers/input/evdev.c:882
evdev_do_ioctl drivers/input/evdev.c:1150 [inline]
In this case we were dealing with a fuzzed HID device that declared over
12K buttons, and while HID layer should not be reporting to us such big
keycodes, we should also be defensive and reject invalid data ourselves as
well.
Reported-by: syzbot+19340dff067c2d3835c0@syzkaller.appspotmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191122204220.GA129459@dtor-ws
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We currently warn the user when tty->port is not set in tty_init_dev
yet. The warning says that the kernel will crash later. And it really
will only few lines below at:
tty->port->itty = tty;
So be nice and avoid the crash -- return an error instead. And update
the warning.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Link: https://lore.kernel.org/r/20191122101721.7222-1-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The interrupt clear flag register is a "write 1 to clear" register.
So, only writing ones allows to clear flags:
- Replace buggy stm32_clr_bits() by a simple write to clear error flags
- Replace useless read/modify/write stm32_set_bits() routine by a
simple write to clear TC (transfer complete) flag.
Fixes: 4f01d833fd ("serial: stm32: fix rx error handling")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/1574323849-1909-1-git-send-email-fabrice.gasnier@st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adjust indentation from seven spaces to tab (+optional two spaces) as in
coding style with command like:
$ sed -e 's/^ /\t/' -i */Kconfig
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20191121132847.29015-1-krzk@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The argument 'inode' passed to tty_open_by_driver() was not being used.
Remove the extra argument.
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Link: https://lore.kernel.org/r/20191120151709.14148-1-sudipm.mukherjee@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adjust indentation from spaces to tab (+optional two spaces) as in
coding style with command like:
$ sed -e 's/^ /\t/' -i */Kconfig
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20191120133843.13189-1-krzk@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Any arm config which has 'CONFIG_MTD_ONENAND_SAMSUNG=m' and
'CONFIG_SERIAL_SAMSUNG=m' gives a build warning:
warning: same module names found:
drivers/tty/serial/samsung.ko
drivers/mtd/nand/onenand/samsung.ko
Rename both drivers/tty/serial/samsung.c to
drivers/tty/serial/samsung_tty.c and drivers/mtd/nand/onenand/samsung.c
drivers/mtd/nand/onenand/samsung_mtd.c to fix the warning.
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Acked-by: Richard Weinberger <richard@nod.at>
Link: https://lore.kernel.org/r/20191117202435.28127-1-sudipm.mukherjee@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver forgets to call pm_runtime_disable in remove.
Add the missed calls to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191118024833.21587-1-hslester96@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PL011's ->flush_buffer() implementation releases and reacquires the port
lock. Due to a race condition here, data can end up being added to the
circular buffer but neither being discarded nor being sent out. This
leads to, for example, tcdrain(2) waiting indefinitely.
Process A Process B
uart_flush_buffer()
- acquire lock
- circ_clear
- pl011_flush_buffer()
-- release lock
-- dmaengine_terminate_all()
uart_write()
- acquire lock
- add chars to circ buffer
- start_tx()
-- start DMA
- release lock
-- acquire lock
-- turn off DMA
-- release lock
// Data in circ buffer but DMA is off
According to the comment in the code, the releasing of the lock around
dmaengine_terminate_all() is to avoid a deadlock with the DMA engine
callback. However, since the time this code was written, the DMA engine
API documentation seems to have been clarified to say that
dmaengine_terminate_all() (in the identically implemented but
differently named dmaengine_terminate_async() variant) does not wait for
any running complete callback to be completed and can even be called
from a complete callback. So there is no possibility of deadlock if the
DMA engine driver implements this API correctly.
So we should be able to just remove this release and reacquire of the
lock to prevent the aforementioned race condition.
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191118092547.32135-1-vincent.whitchurch@axis.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit f33cf77661.
As Johan says, this driver needs a lot more work and these changes are
only going in the wrong direction:
https://lkml.kernel.org/r/20190523091839.GC568@localhost
Reported-by: Johan Hovold <johan@kernel.org>
Cc: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 62104b280a.
As Johan says, this driver needs a lot more work and these changes are
only going in the wrong direction:
https://lkml.kernel.org/r/20190523091839.GC568@localhost
Reported-by: Johan Hovold <johan@kernel.org>
Cc: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 3b209d253e.
As Johan says, this driver needs a lot more work and these changes are
only going in the wrong direction:
https://lkml.kernel.org/r/20190523091839.GC568@localhost
Reported-by: Johan Hovold <johan@kernel.org>
Cc: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 0379b1163e.
As Johan says, this driver needs a lot more work and these changes are
only going in the wrong direction:
https://lkml.kernel.org/r/20190523091839.GC568@localhost
Reported-by: Johan Hovold <johan@kernel.org>
Cc: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit d338838c09.
As Johan says, this driver needs a lot more work and these changes are
only going in the wrong direction:
https://lkml.kernel.org/r/20190523091839.GC568@localhost
Reported-by: Johan Hovold <johan@kernel.org>
Cc: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit a00d9db895.
As Johan says, this driver needs a lot more work and these changes are
only going in the wrong direction:
https://lkml.kernel.org/r/20190523091839.GC568@localhost
Reported-by: Johan Hovold <johan@kernel.org>
Cc: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When running in M-mode we can't use SBI based drivers. Add a new
CONFIG_RISCV_SBI that drivers that do SBI calls can depend on
instead.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Change logic how console_port is setup by using CON_ENABLED flag
instead of index. There will be unique uart_console
structure that's why code can't use id for console_port
assignment.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Link: https://lore.kernel.org/r/1573555271-2579-1-git-send-email-shubhrajyoti.datta@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Per Documentation/DMA-API-HOWTO.txt,
To unmap a scatterlist, just call:
dma_unmap_sg(dev, sglist, nents, direction);
.. note::
The 'nents' argument to the dma_unmap_sg call must be
the _same_ one you passed into the dma_map_sg call,
it should _NOT_ be the 'count' value _returned_ from the
dma_map_sg call.
However in the driver, priv->nent is directly assigned with value
returned from dma_map_sg, and dma_unmap_sg use priv->nent for unmap,
this breaks the API usage.
So introduce a new entry orig_nent to remember 'nents'.
Fixes: da3564ee02 ("pch_uart: add multi-scatter processing")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/1573623259-6339-1-git-send-email-peng.fan@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dmaengine_prep_slave_sg needs to use sg count returned
by dma_map_sg, not use sport->dma_tx_nents, because the return
value of dma_map_sg is not always same with "nents".
Fixes: b4cdc8f61b ("serial: imx: add DMA support for imx6q")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/1573108875-26530-1-git-send-email-peng.fan@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This means removing support for checking magic in amiserial.c
(SERIAL_PARANOIA_CHECK option), which was checking a magic field which
doesn't currently exist in the struct. That code hasn't built at least
since git.
Removing the definition from the header is safe anyway as that code was
from another driver and not including it.
Signed-off-by: Pascal Terjan <pterjan@google.com>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lore.kernel.org/r/20191105192749.67533-1-pterjan@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dmaengine_prep_slave_sg needs to use sg count returned
by dma_map_sg, not use sport->dma_tx_nents, because the return
value of dma_map_sg is not always same with "nents".
When enabling iommu for lpuart + edma, iommu framework may concatenate
two sgs into one.
Fixes: 6250cc30c4 ("tty: serial: fsl_lpuart: Use scatter/gather DMA for Tx")
Cc: <stable@vger.kernel.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/1572932977-17866-1-git-send-email-peng.fan@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 7726fb53e7.
Jiri writes:
On 24. 09. 19, 11:25, Xiaoming Ni wrote:
> According to the comment of tty_port_destroy():
> When a port was initialized using tty_port_init, one has to destroy
> the port by tty_port_destroy();
It continues with a part saying:
Either indirectly by using tty_port refcounting
(tty_port_put) or directly if refcounting is not used.
So this should be reverted.
Cc: Xiaoming Ni <nixiaoming@huawei.com>
Reported-by: Jiri Slaby <jslaby@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver uses clk_prepare_enable in ulite_probe but uses clk_unprepare
in ulite_remove, which does not match.
Replace clk_unprepare with clk_disable_unprepare to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Link: https://lore.kernel.org/r/20191101085433.10399-1-hslester96@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As platform_get_irq() now prints an error when the interrupt does not
exist, this warnings are printed on bananapi-r2:
[ 4.935780] mt6577-uart 11004000.serial: IRQ index 1 not found
[ 4.962589] 11002000.serial: ttyS1 at MMIO 0x11002000 (irq = 202, base_baud = 1625000) is a ST16650V2
[ 4.972127] mt6577-uart 11002000.serial: IRQ index 1 not found
[ 4.998927] 11003000.serial: ttyS2 at MMIO 0x11003000 (irq = 203, base_baud = 1625000) is a ST16650V2
[ 5.008474] mt6577-uart 11003000.serial: IRQ index 1 not found
Fix this by calling platform_get_irq_optional() instead.
now it looks like this:
[ 4.872751] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
Fixes: 7723f4c5ec ("driver core: platform: Add an error message to platform_get_irq*()")
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191027062117.20389-1-frank-w@public-files.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the commit 7723f4c5ec ("driver core: platform: Add an error message
to platform_get_irq*()") platform_get_irq() started issuing an error message.
Thus, there is no need to have the same in the driver
Fixes: 7723f4c5ec ("driver core: platform: Add an error message to platform_get_irq*()")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191023103558.51862-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
hci_qca interfaces to the wcn3990 via a uart_dm on the msm8998 mtp and
Lenovo Miix 630 laptop. As part of initializing the wcn3990, hci_qca
disables flow, configures the uart baudrate, and then reenables flow - at
which point an event is expected to be received over the uart from the
wcn3990. It is observed that this event comes after the baudrate change
but before hci_qca re-enables flow. This is unexpected, and is a result of
msm_reset() being broken.
According to the uart_dm hardware documentation, it is recommended that
automatic hardware flow control be enabled by setting RX_RDY_CTL. Auto
hw flow control will manage RFR based on the configured watermark. When
there is space to receive data, the hw will assert RFR. When the watermark
is hit, the hw will de-assert RFR.
The hardware documentation indicates that RFR can me manually managed via
CR when RX_RDY_CTL is not set. SET_RFR asserts RFR, and RESET_RFR
de-asserts RFR.
msm_reset() is broken because after resetting the hardware, it
unconditionally asserts RFR via SET_RFR. This enables flow regardless of
the current configuration, and would undo a previous flow disable
operation. It should instead de-assert RFR via RESET_RFR to block flow
until the hardware is reconfigured. msm_serial should rely on the client
to specify that flow should be enabled, either via mctrl() or the termios
structure, and only assert RFR in response to those triggers.
Fixes: 04896a77a9 ("msm_serial: serial driver for MSM7K onboard serial peripheral.")
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Andy Gross <agross@kernel.org>
Link: https://lore.kernel.org/r/20191021154616.25457-1-jeffrey.l.hugo@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The build of xtensa allmodconfig gives warning of:
In function 'get_ports.isra.0':
warning: the frame size of 1040 bytes is larger than 1024 bytes
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Acked-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20191018161712.27807-1-sudipm.mukherjee@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commits adds RS485 support for LPUART hardware that uses 32-bit
registers. These are typically found in i.MX8 processors.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Reviewed-by: Fugang Duan <fugang.duan@nxp.com>
Link: https://lore.kernel.org/r/20191017141428.10330-3-philippe.schenker@toradex.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use define from the 32-bit register description UARTMODIR_* instead of
UARTMODEM_*. The value is the same, so there is no functional change.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Reviewed-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Fugang Duan <fugang.duan@nxp.com>
Link: https://lore.kernel.org/r/20191017141428.10330-2-philippe.schenker@toradex.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
