Same as in tcp_v6_err() and __udp6_lib_err(), there's no need to
hold idev in sctp_v6_err(), so just call __in6_dev_get() instead.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sctp_transport_pl_reset() is called whenever any of these 3 members in
transport is changed:
- probe_interval
- param_flags & SPP_PMTUD_ENABLE
- state == ACTIVE
If all are true, start the PLPMTUD when it's not yet started. If any of
these is false, stop the PLPMTUD when it's already running.
sctp_transport_pl_update() is called when the transport dst has changed.
It will restart the PLPMTUD probe. Again, the pathmtu won't change but
use the dst's mtu until the Search phase is done.
Note that after using PLPMTUD, the pathmtu is only initialized with the
dst mtu when the transport dst changes. At other time it is updated by
pl.pmtu. So sctp_transport_pmtu_check() will be called only when PLPMTUD
is disabled in sctp_packet_config().
After this patch, the PLPMTUD feature from RFC8899 will be activated
and can be used by users.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PLPMTUD will short-circuit the old process for icmp TOOBIG packets.
This part is described in rfc8899#section-4.6.2 (PL_PTB_SIZE =
PTB_SIZE - other_headers_len). Note that from rfc8899#section-5.2
State Machine, each case below is for some specific states only:
a) PL_PTB_SIZE < MIN_PLPMTU || PL_PTB_SIZE >= PROBED_SIZE,
discard it, for any state
b) MIN_PLPMTU < PL_PTB_SIZE < BASE_PLPMTU,
Base -> Error, for Base state
c) BASE_PLPMTU <= PL_PTB_SIZE < PLPMTU,
Search -> Base or Complete -> Base, for Search and Complete states.
d) PLPMTU < PL_PTB_SIZE < PROBED_SIZE,
set pl.probe_size to PL_PTB_SIZE then verify it, for Search state.
The most important one is case d), which will help find the optimal
fast during searching. Like when pathmtu = 1392 for SCTP over IPv4,
the search will be (20 is iphdr_len):
1. probe with 1200 - 20
2. probe with 1232 - 20
3. probe with 1264 - 20
...
7. probe with 1388 - 20
8. probe with 1420 - 20
When sending the probe with 1420 - 20, TOOBIG may come with PL_PTB_SIZE =
1392 - 20. Then it matches case d), and saves some rounds to try with the
1392 - 20 probe. But of course, PLPMTUD doesn't trust TOOBIG packets, and
it will go back to the common searching once the probe with the new size
can't be verified.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As described in rfc8899#section-5.2, when a probe succeeds, there might
be the following state transitions:
- Base -> Search, occurs when probe succeeds with BASE_PLPMTU,
pl.pmtu is not changing,
pl.probe_size increases by SCTP_PL_BIG_STEP,
- Error -> Search, occurs when probe succeeds with BASE_PLPMTU,
pl.pmtu is changed from SCTP_MIN_PLPMTU to SCTP_BASE_PLPMTU,
pl.probe_size increases by SCTP_PL_BIG_STEP.
- Search -> Search Complete, occurs when probe succeeds with the probe
size SCTP_MAX_PLPMTU less than pl.probe_high,
pl.pmtu is not changing, but update *pathmtu* with it,
pl.probe_size is set back to pl.pmtu to double check it.
- Search Complete -> Search, occurs when probe succeeds with the probe
size equal to pl.pmtu,
pl.pmtu is not changing,
pl.probe_size increases by SCTP_PL_MIN_STEP.
So search process can be described as:
1. When it just enters 'Search' state, *pathmtu* is not updated with
pl.pmtu, and probe_size increases by a big step (SCTP_PL_BIG_STEP)
each round.
2. Until pl.probe_high is set when a probe fails, and probe_size
decreases back to pl.pmtu, as described in the last patch.
3. When the probe with the new size succeeds, probe_size changes to
increase by a small step (SCTP_PL_MIN_STEP) due to pl.probe_high
is set.
4. Until probe_size is next to pl.probe_high, the searching finishes and
it goes to 'Complete' state and updates *pathmtu* with pl.pmtu, and
then probe_size is set to pl.pmtu to confirm by once more probe.
5. This probe occurs after "30 * probe_inteval", a much longer time than
that in Search state. Once it is done it goes to 'Search' state again
with probe_size increased by SCTP_PL_MIN_STEP.
As we can see above, during the searching, pl.pmtu changes while *pathmtu*
doesn't. *pathmtu* is only updated when the search finishes by which it
gets an optimal value for it. A big step is used at the beginning until
it gets close to the optimal value, then it changes to a small step until
it has this optimal value.
The small step is also used in 'Complete' until it goes to 'Search' state
again and the probe with 'pmtu + the small step' succeeds, which means a
higher size could be used. Then probe_size changes to increase by a big
step again until it gets close to the next optimal value.
Note that anytime when black hole is detected, it goes directly to 'Base'
state with pl.pmtu set to SCTP_BASE_PLPMTU, as described in the last patch.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The state transition is described in rfc8899#section-5.2,
PROBE_COUNT == MAX_PROBES means the probe fails for MAX times, and the
state transition includes:
- Base -> Error, occurs when BASE_PLPMTU Confirmation Fails,
pl.pmtu is set to SCTP_MIN_PLPMTU,
probe_size is still SCTP_BASE_PLPMTU;
- Search -> Base, occurs when Black Hole Detected,
pl.pmtu is set to SCTP_BASE_PLPMTU,
probe_size is set back to SCTP_BASE_PLPMTU;
- Search Complete -> Base, occurs when Black Hole Detected
pl.pmtu is set to SCTP_BASE_PLPMTU,
probe_size is set back to SCTP_BASE_PLPMTU;
Note a black hole is encountered when a sender is unaware that packets
are not being delivered to the destination endpoint. So it includes the
probe failures with equal probe_size to pl.pmtu, and definitely not
include that with greater probe_size than pl.pmtu. The later one is the
normal probe failure where probe_size should decrease back to pl.pmtu
and pl.probe_high is set. pl.probe_high would be used on HB ACK recv
path in the next patch.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch does exactly what rfc8899#section-6.2.1.2 says:
The SCTP sender needs to be able to determine the total size of a
probe packet. The HEARTBEAT chunk could carry a Heartbeat
Information parameter that includes, besides the information
suggested in [RFC4960], the probe size to help an implementation
associate a HEARTBEAT ACK with the size of probe that was sent. The
sender could also use other methods, such as sending a nonce and
verifying the information returned also contains the corresponding
nonce. The length of the PAD chunk is computed by reducing the
probing size by the size of the SCTP common header and the HEARTBEAT
chunk.
Note that HB ACK chunk will carry back whatever HB chunk carried, including
the probe_size we put it in; We also check hbinfo->probe_size in the HB ACK
against link->pl.probe_size to validate this HB ACK chunk.
v1->v2:
- Remove the unused 'sp' and add static for sctp_packet_bundle_pad().
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are 3 timers described in rfc8899#section-5.1.1:
PROBE_TIMER, PMTU_RAISE_TIMER, CONFIRMATION_TIMER
This patches adds a 'probe_timer' in transport, and it works as either
PROBE_TIMER or PMTU_RAISE_TIMER. At most time, it works as PROBE_TIMER
and expires every a 'probe_interval' time to send the HB probe packet.
When transport pl enters COMPLETE state, it works as PMTU_RAISE_TIMER
and expires in 'probe_interval * 30' time to go back to SEARCH state
and do searching again.
SCTP HB is an acknowledged packet, CONFIRMATION_TIMER is not needed.
The timer will start when transport pl enters BASE state and stop
when it enters DISABLED state.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With this socket option, users can change probe_interval for
a transport, asoc or sock after it's created.
Note that if the change is for an asoc, also apply the change
to each transport in this asoc.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PLPMTUD can be enabled by doing 'sysctl -w net.sctp.probe_interval=n'.
'n' is the interval for PLPMTUD probe timer in milliseconds, and it
can't be less than 5000 if it's not 0.
All asoc/transport's PLPMTUD in a new socket will be enabled by default.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This chunk is defined in rfc4820#section-3, and used to pad an
SCTP packet. The receiver must discard this chunk and continue
processing the rest of the chunks in the packet.
Add it now, as it will be bundled with a heartbeat chunk to probe
pmtu in the following patches.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
proc_dointvec() cannot do min and max check for setting a value
when extra1/extra2 is set, so change it to proc_dointvec_minmax()
for sysctl encap_port.
Fixes: e8a3001c21 ("sctp: add encap_port for netns sock asoc and transport")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to add the missing setting back for asoc encap_port.
Fixes: 8dba29603b ("sctp: add SCTP_REMOTE_UDP_ENCAPS_PORT sockopt")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enable -Wimplicit-fallthrough for Clang, fix a couple
of warnings by explicitly adding a break statement and replacing a
comment with a goto statement instead of letting the code fall through
to the next case.
Link: https://github.com/KSPP/linux/issues/115
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Every protocol has the 'netns_ok' member and it is euqal to 1. The
'if (!prot->netns_ok)' always false in inet_add_protocol().
Signed-off-by: Yejune Deng <yejunedeng@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As Or Cohen described:
If sctp_destroy_sock is called without sock_net(sk)->sctp.addr_wq_lock
held and sp->do_auto_asconf is true, then an element is removed
from the auto_asconf_splist without any proper locking.
This can happen in the following functions:
1. In sctp_accept, if sctp_sock_migrate fails.
2. In inet_create or inet6_create, if there is a bpf program
attached to BPF_CGROUP_INET_SOCK_CREATE which denies
creation of the sctp socket.
This patch is to fix it by moving the auto_asconf init out of
sctp_init_sock(), by which inet_create()/inet6_create() won't
need to operate it in sctp_destroy_sock() when calling
sk_common_release().
It also makes more sense to do auto_asconf init while binding the
first addr, as auto_asconf actually requires an ANY addr bind,
see it in sctp_addr_wq_timeout_handler().
This addresses CVE-2021-23133.
Fixes: 6102365876 ("bpf: Add new cgroup attach type to enable sock modifications")
Reported-by: Or Cohen <orcohen@paloaltonetworks.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit b166a20b07.
This one has to be reverted as it introduced a dead lock, as
syzbot reported:
CPU0 CPU1
---- ----
lock(&net->sctp.addr_wq_lock);
lock(slock-AF_INET6);
lock(&net->sctp.addr_wq_lock);
lock(slock-AF_INET6);
CPU0 is the thread of sctp_addr_wq_timeout_handler(), and CPU1
is that of sctp_close().
The original issue this commit fixed will be fixed in the next
patch.
Reported-by: syzbot+959223586843e69a2674@syzkaller.appspotmail.com
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Normally SCTP_MIB_CURRESTAB is always incremented once asoc enter into
ESTABLISHED from the state < ESTABLISHED and decremented when the asoc
is being deleted.
However, in sctp_sf_do_dupcook_b(), the asoc's state can be changed to
ESTABLISHED from the state >= ESTABLISHED where it shouldn't increment
SCTP_MIB_CURRESTAB. Otherwise, one asoc may increment MIB_CURRESTAB
multiple times but only decrement once at the end.
I was able to reproduce it by using scapy to do the 4-way shakehands,
after that I replayed the COOKIE-ECHO chunk with 'peer_vtag' field
changed to different values, and SCTP_MIB_CURRESTAB was incremented
multiple times and never went back to 0 even when the asoc was freed.
This patch is to fix it by only incrementing SCTP_MIB_CURRESTAB when
the state < ESTABLISHED in sctp_sf_do_dupcook_b().
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reported-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 12dfd78e3a.
This can be reverted as shutdown and cookie_ack chunk are using the
same asoc since commit 35b4f24415 ("sctp: do asoc update earlier
in sctp_sf_do_dupcook_a").
Reported-by: Jere Leppänen <jere.leppanen@nokia.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 7e9269a5ac.
As Jere notice, commit 35b4f24415 ("sctp: do asoc update earlier
in sctp_sf_do_dupcook_a") only keeps the SHUTDOWN and COOKIE-ACK
with the same asoc, not transport. So we have to bring this patch
back.
Reported-by: Jere Leppänen <jere.leppanen@nokia.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The same thing should be done for sctp_sf_do_dupcook_b().
Meanwhile, SCTP_CMD_UPDATE_ASSOC cmd can be removed.
v1->v2:
- Fix the return value in sctp_sf_do_assoc_update().
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This can be reverted as shutdown and cookie_ack chunk are using the
same asoc since the last patch.
This reverts commit 145cb2f717.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's a panic that occurs in a few of envs, the call trace is as below:
[] general protection fault, ... 0x29acd70f1000a: 0000 [#1] SMP PTI
[] RIP: 0010:sctp_ulpevent_notify_peer_addr_change+0x4b/0x1fa [sctp]
[] sctp_assoc_control_transport+0x1b9/0x210 [sctp]
[] sctp_do_8_2_transport_strike.isra.16+0x15c/0x220 [sctp]
[] sctp_cmd_interpreter.isra.21+0x1231/0x1a10 [sctp]
[] sctp_do_sm+0xc3/0x2a0 [sctp]
[] sctp_generate_timeout_event+0x81/0xf0 [sctp]
This is caused by a transport use-after-free issue. When processing a
duplicate COOKIE-ECHO chunk in sctp_sf_do_dupcook_a(), both COOKIE-ACK
and SHUTDOWN chunks are allocated with the transort from the new asoc.
However, later in the sideeffect machine, the old asoc is used to send
them out and old asoc's shutdown_last_sent_to is set to the transport
that SHUTDOWN chunk attached to in sctp_cmd_setup_t2(), which actually
belongs to the new asoc. After the new_asoc is freed and the old asoc
T2 timeout, the old asoc's shutdown_last_sent_to that is already freed
would be accessed in sctp_sf_t2_timer_expire().
Thanks Alexander and Jere for helping dig into this issue.
To fix it, this patch is to do the asoc update first, then allocate
the COOKIE-ACK and SHUTDOWN chunks with the 'updated' old asoc. This
would make more sense, as a chunk from an asoc shouldn't be sent out
with another asoc. We had fixed quite a few issues caused by this.
Fixes: 145cb2f717 ("sctp: Fix bundling of SHUTDOWN with COOKIE-ACK")
Reported-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Reported-by: syzbot+bbe538efd1046586f587@syzkaller.appspotmail.com
Reported-by: Michal Tesar <mtesar@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
- keep the ZC code, drop the code related to reinit
net/bridge/netfilter/ebtables.c
- fix build after move to net_generic
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix the following out-of-bounds warning:
net/sctp/sm_make_chunk.c:3150:4: warning: 'memcpy' offset [17, 28] from the object at 'addr' is out of the bounds of referenced subobject 'v4' with type 'struct sockaddr_in' at offset 0 [-Warray-bounds]
This helps with the ongoing efforts to globally enable -Warray-bounds
and get us closer to being able to tighten the FORTIFY_SOURCE routines
on memcpy().
Link: https://github.com/KSPP/linux/issues/109
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If sctp_destroy_sock is called without sock_net(sk)->sctp.addr_wq_lock
held and sp->do_auto_asconf is true, then an element is removed
from the auto_asconf_splist without any proper locking.
This can happen in the following functions:
1. In sctp_accept, if sctp_sock_migrate fails.
2. In inet_create or inet6_create, if there is a bpf program
attached to BPF_CGROUP_INET_SOCK_CREATE which denies
creation of the sctp socket.
The bug is fixed by acquiring addr_wq_lock in sctp_destroy_sock
instead of sctp_close.
This addresses CVE-2021-23133.
Reported-by: Or Cohen <orcohen@paloaltonetworks.com>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Fixes: 6102365876 ("bpf: Add new cgroup attach type to enable sock modifications")
Signed-off-by: Or Cohen <orcohen@paloaltonetworks.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
MAINTAINERS
- keep Chandrasekar
drivers/net/ethernet/mellanox/mlx5/core/en_main.c
- simple fix + trust the code re-added to param.c in -next is fine
include/linux/bpf.h
- trivial
include/linux/ethtool.h
- trivial, fix kdoc while at it
include/linux/skmsg.h
- move to relevant place in tcp.c, comment re-wrapped
net/core/skmsg.c
- add the sk = sk // sk = NULL around calls
net/tipc/crypto.c
- trivial
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Found by virtue of ipv6 raw sockets not honouring the per-socket
IP{,V6}_FREEBIND setting.
Based on hits found via:
git grep '[.]ip_nonlocal_bind'
We fix both raw ipv6 sockets to honour IP{,V6}_FREEBIND and IP{,V6}_TRANSPARENT,
and we fix sctp sockets to honour IP{,V6}_TRANSPARENT (they already honoured
FREEBIND), and not just the ipv6 'ip_nonlocal_bind' sysctl.
The helper is defined as:
static inline bool ipv6_can_nonlocal_bind(struct net *net, struct inet_sock *inet) {
return net->ipv6.sysctl.ip_nonlocal_bind || inet->freebind || inet->transparent;
}
so this change only widens the accepted opt-outs and is thus a clean bugfix.
I'm not entirely sure what 'fixes' tag to add, since this is AFAICT an ancient bug,
but IMHO this should be applied to stable kernels as far back as possible.
As such I'm adding a 'fixes' tag with the commit that originally added the helper,
which happened in 4.19. Backporting to older LTS kernels (at least 4.9 and 4.14)
would presumably require open-coding it or backporting the helper as well.
Other possibly relevant commits:
v4.18-rc6-1502-g83ba4645152d net: add helpers checking if socket can be bound to nonlocal address
v4.18-rc6-1431-gd0c1f01138c4 net/ipv6: allow any source address for sendmsg pktinfo with ip_nonlocal_bind
v4.14-rc5-271-gb71d21c274ef sctp: full support for ipv6 ip_nonlocal_bind & IP_FREEBIND
v4.7-rc7-1883-g9b9742022888 sctp: support ipv6 nonlocal bind
v4.1-12247-g35a256fee52c ipv6: Nonlocal bind
Cc: Lorenzo Colitti <lorenzo@google.com>
Fixes: 83ba464515 ("net: add helpers checking if socket can be bound to nonlocal address")
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Reviewed-By: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify "unkown" to "unknown" in net/sctp/sm_make_chunk.c and
Modify "orginal" to "original" in net/sctp/socket.c.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Lu Wei <luwei32@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
s/simulataneous/simultaneous/ ....in three dirrent places.
s/tempory/temporary/
s/interpeter/interpreter/
Signed-off-by: Bhaskar Chowdhury <unixbhaskar@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sk's sk_route_caps is set in sctp_packet_config, and later it
only needs to change when traversing the transport_list in a loop,
as the dst might be changed in the tx path.
So move sk_route_caps check and set into sctp_outq_flush_transports
from sctp_packet_transmit. This also fixes a dst leak reported by
Chen Yi:
https://bugzilla.kernel.org/show_bug.cgi?id=212227
As calling sk_setup_caps() in sctp_packet_transmit may also set the
sk_route_caps for the ctrl sock in a netns. When the netns is being
deleted, the ctrl sock's releasing is later than dst dev's deleting,
which will cause this dev's deleting to hang and dmesg error occurs:
unregister_netdevice: waiting for xxx to become free. Usage count = 1
Reported-by: Chen Yi <yiche@redhat.com>
Fixes: bcd623d8e9 ("sctp: call sk_setup_caps in sctp_packet_transmit instead")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix typo of 'overflow' for comment in sctp_tsnmap_check().
Reported-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Drew Fustini <drew@beagleboard.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sctp transport seq_file iterators take a reference to the transport
in the ->start and ->next functions and releases the reference in the
->show function. The preferred handling for such resources is to
release them in the subsequent ->next or ->stop function call.
Since Commit 1f4aace60b ("fs/seq_file.c: simplify seq_file iteration
code and interface") there is no guarantee that ->show will be called
after ->next, so this function can now leak references.
So move the sctp_transport_put() call to ->next and ->stop.
Fixes: 1f4aace60b ("fs/seq_file.c: simplify seq_file iteration code and interface")
Reported-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
It makes more sense to clear NETIF_F_SG instead of set it when
calling skb_segment() in sctp_gso_segment(), since SCTP GSO is
using head_skb's fraglist, of which all frags are linear skbs.
This will make SCTP GSO code more understandable.
Suggested-by: Alexander Duyck <alexander.duyck@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A call trace was found in Hangbin's Codenomicon testing with debug kernel:
[ 2615.981988] ODEBUG: free active (active state 0) object type: timer_list hint: sctp_generate_proto_unreach_event+0x0/0x3a0 [sctp]
[ 2615.995050] WARNING: CPU: 17 PID: 0 at lib/debugobjects.c:328 debug_print_object+0x199/0x2b0
[ 2616.095934] RIP: 0010:debug_print_object+0x199/0x2b0
[ 2616.191533] Call Trace:
[ 2616.194265] <IRQ>
[ 2616.202068] debug_check_no_obj_freed+0x25e/0x3f0
[ 2616.207336] slab_free_freelist_hook+0xeb/0x140
[ 2616.220971] kfree+0xd6/0x2c0
[ 2616.224293] rcu_do_batch+0x3bd/0xc70
[ 2616.243096] rcu_core+0x8b9/0xd00
[ 2616.256065] __do_softirq+0x23d/0xacd
[ 2616.260166] irq_exit+0x236/0x2a0
[ 2616.263879] smp_apic_timer_interrupt+0x18d/0x620
[ 2616.269138] apic_timer_interrupt+0xf/0x20
[ 2616.273711] </IRQ>
This is because it holds asoc when transport->proto_unreach_timer starts
and puts asoc when the timer stops, and without holding transport the
transport could be freed when the timer is still running.
So fix it by holding/putting transport instead for proto_unreach_timer
in transport, just like other timers in transport.
v1->v2:
- Also use sctp_transport_put() for the "out_unlock:" path in
sctp_generate_proto_unreach_event(), as Marcelo noticed.
Fixes: 50b5d6ad63 ("sctp: Fix a race between ICMP protocol unreachable and connect()")
Reported-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Link: https://lore.kernel.org/r/102788809b554958b13b95d33440f5448113b8d6.1605331373.git.lucien.xin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
inet(6)_skb_parm was removed from sctp_input_cb by Commit a1dd2cf2f1
("sctp: allow changing transport encap_port by peer packets"), as it
thought sctp_input_cb->header is not used any more in SCTP.
syzbot reported a crash:
[ ] BUG: KASAN: use-after-free in decode_session6+0xe7c/0x1580
[ ]
[ ] Call Trace:
[ ] <IRQ>
[ ] dump_stack+0x107/0x163
[ ] kasan_report.cold+0x1f/0x37
[ ] decode_session6+0xe7c/0x1580
[ ] __xfrm_policy_check+0x2fa/0x2850
[ ] sctp_rcv+0x12b0/0x2e30
[ ] sctp6_rcv+0x22/0x40
[ ] ip6_protocol_deliver_rcu+0x2e8/0x1680
[ ] ip6_input_finish+0x7f/0x160
[ ] ip6_input+0x9c/0xd0
[ ] ipv6_rcv+0x28e/0x3c0
It was caused by sctp_input_cb->header/IP6CB(skb) still used in sctp rx
path decode_session6() but some members overwritten by sctp6_rcv().
This patch is to fix it by bring inet(6)_skb_parm back to sctp_input_cb
and not overwriting it in sctp4/6_rcv() and sctp_udp_rcv().
Reported-by: syzbot+5be8aebb1b7dfa90ef31@syzkaller.appspotmail.com
Fixes: a1dd2cf2f1 ("sctp: allow changing transport encap_port by peer packets")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Link: https://lore.kernel.org/r/136c1a7a419341487c504be6d1996928d9d16e02.1604472932.git.lucien.xin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit 978aa04741 ("sctp: fix some type cast warnings introduced since
very beginning")' broke err reading from sctp_arg, because it reads the
value as 32-bit integer, although the value is stored as 16-bit integer.
Later this value is passed to the userspace in 16-bit variable, thus the
user always gets 0 on big-endian platforms. Fix it by reading the __u16
field of sctp_arg union, as reading err field would produce a sparse
warning.
Fixes: 978aa04741 ("sctp: fix some type cast warnings introduced since very beginning")
Signed-off-by: Petr Malat <oss@malat.biz>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Link: https://lore.kernel.org/r/20201030132633.7045-1-oss@malat.biz
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch is to enable udp tunneling socks by calling
sctp_udp_sock_start() in sctp_ctrlsock_init(), and
sctp_udp_sock_stop() in sctp_ctrlsock_exit().
Also add sysctl udp_port to allow changing the listening
sock's port by users.
Wit this patch, the whole sctp over udp feature can be
enabled and used.
v1->v2:
- Also update ctl_sock udp_port in proc_sctp_do_udp_port()
where netns udp_port gets changed.
v2->v3:
- Call htons() when setting sk udp_port from netns udp_port.
v3->v4:
- Not call sctp_udp_sock_start() when new_value is 0.
- Add udp_port entry in ip-sysctl.rst.
v4->v5:
- Not call sctp_udp_sock_start/stop() in sctp_ctrlsock_init/exit().
- Improve the description of udp_port in ip-sysctl.rst.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This is from Section 4 of draft-tuexen-tsvwg-sctp-udp-encaps-cons-03,
and it requires responding with an abort chunk with an error cause
when the udp source port of the received init chunk doesn't match the
encap port of the transport.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch is to add the function to make the abort chunk with
the error cause for new encapsulation port restart, defined
on Section 4.4 in draft-tuexen-tsvwg-sctp-udp-encaps-cons-03.
v1->v2:
- no change.
v2->v3:
- no need to call htons() when setting nep.cur_port/new_port.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This one basically does the similar things in sctp_v6_xmit as does for
udp4 sock in the last patch, just note that:
1. label needs to be calculated, as it's the param of
udp_tunnel6_xmit_skb().
2. The 'nocheck' param of udp_tunnel6_xmit_skb() is false, as
required by RFC.
v1->v2:
- Use sp->udp_port instead in sctp_v6_xmit(), which is more safe.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch does what the rfc6951#section-5.3 says for ipv4:
"Within the UDP header, the source port MUST be the local UDP
encapsulation port number of the SCTP stack, and the destination port
MUST be the remote UDP encapsulation port number maintained for the
association and the destination address to which the packet is sent
(see Section 5.1).
Because the SCTP packet is the UDP payload, the length of the UDP
packet MUST be the length of the SCTP packet plus the size of the UDP
header.
The SCTP checksum MUST be computed for IPv4 and IPv6, and the UDP
checksum SHOULD be computed for IPv4 and IPv6."
Some places need to be adjusted in sctp_packet_transmit():
1. For non-gso packets, when transport's encap_port is set, sctp
checksum has to be done in sctp_packet_pack(), as the outer
udp will use ip_summed = CHECKSUM_PARTIAL to do the offload
setting for checksum.
2. Delay calling dst_clone() and skb_dst_set() for non-udp packets
until sctp_v4_xmit(), as for udp packets, skb_dst_set() is not
needed before calling udp_tunnel_xmit_skb().
then in sctp_v4_xmit():
1. Go to udp_tunnel_xmit_skb() only when transport->encap_port and
net->sctp.udp_port both are set, as these are one for dst port
and another for src port.
2. For gso packet, SKB_GSO_UDP_TUNNEL_CSUM is set for gso_type, and
with this udp checksum can be done in __skb_udp_tunnel_segment()
for each segments after the sctp gso.
3. inner_mac_header and inner_transport_header are set, as these
will be needed in __skb_udp_tunnel_segment() to find the right
headers.
4. df and ttl are calculated, as these are the required params by
udp_tunnel_xmit_skb().
5. nocheck param has to be false, as "the UDP checksum SHOULD be
computed for IPv4 and IPv6", says in rfc6951#section-5.3.
v1->v2:
- Use sp->udp_port instead in sctp_v4_xmit(), which is more safe.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
sk_setup_caps() was originally called in Commit 90017accff ("sctp:
Add GSO support"), as:
"We have to refresh this in case we are xmiting to more than one
transport at a time"
This actually happens in the loop of sctp_outq_flush_transports(),
and it shouldn't be tied to gso, so move it out of gso part and
before sctp_packet_pack().
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
sctp_mtu_payload() is for calculating the frag size before making
chunks from a msg. So we should only add udphdr size to overhead
when udp socks are listening, as only then sctp can handle the
incoming sctp over udp packets and outgoing sctp over udp packets
will be possible.
Note that we can't do this according to transport->encap_port, as
different transports may be set to different values, while the
chunks were made before choosing the transport, we could not be
able to meet all rfc6951#section-5.6 recommends.
v1->v2:
- Add udp_port for sctp_sock to avoid a potential race issue, it
will be used in xmit path in the next patch.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As rfc6951#section-5.4 says:
"After finding the SCTP association (which
includes checking the verification tag), the UDP source port MUST be
stored as the encapsulation port for the destination address the SCTP
packet is received from (see Section 5.1).
When a non-encapsulated SCTP packet is received by the SCTP stack,
the encapsulation of outgoing packets belonging to the same
association and the corresponding destination address MUST be
disabled."
transport encap_port should be updated by a validated incoming packet's
udp src port.
We save the udp src port in sctp_input_cb->encap_port, and then update
the transport in two places:
1. right after vtag is verified, which is required by RFC, and this
allows the existent transports to be updated by the chunks that
can only be processed on an asoc.
2. right before processing the 'init' where the transports are added,
and this allows building a sctp over udp connection by client with
the server not knowing the remote encap port.
3. when processing ootb_pkt and creating the temporary transport for
the reply pkt.
Note that sctp_input_cb->header is removed, as it's not used any more
in sctp.
v1->v2:
- Change encap_port as __be16 for sctp_input_cb.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch is to implement:
rfc6951#section-6.1: Get or Set the Remote UDP Encapsulation Port Number
with the param of the struct:
struct sctp_udpencaps {
sctp_assoc_t sue_assoc_id;
struct sockaddr_storage sue_address;
uint16_t sue_port;
};
the encap_port of sock, assoc or transport can be changed by users,
which also means it allows the different transports of the same asoc
to have different encap_port value.
v1->v2:
- no change.
v2->v3:
- fix the endian warning when setting values between encap_port and
sue_port.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
encap_port is added as per netns/sock/assoc/transport, and the
latter one's encap_port inherits the former one's by default.
The transport's encap_port value would mostly decide if one
packet should go out with udp encapsulated or not.
This patch also allows users to set netns' encap_port by sysctl.
v1->v2:
- Change to define encap_port as __be16 for sctp_sock, asoc and
transport.
v2->v3:
- No change.
v3->v4:
- Add 'encap_port' entry in ip-sysctl.rst.
v4->v5:
- Improve the description of encap_port in ip-sysctl.rst.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As it says in rfc6951#section-5.5:
"When receiving ICMP or ICMPv6 response packets, there might not be
enough bytes in the payload to identify the SCTP association that the
SCTP packet triggering the ICMP or ICMPv6 packet belongs to. If a
received ICMP or ICMPv6 packet cannot be related to a specific SCTP
association or the verification tag cannot be verified, it MUST be
discarded silently. In particular, this means that the SCTP stack
MUST NOT rely on receiving ICMP or ICMPv6 messages. Implementation
constraints could prevent processing received ICMP or ICMPv6
messages."
ICMP or ICMPv6 packets need to be handled, and this is implemented by
udp encap sock .encap_err_lookup function.
The .encap_err_lookup function is called in __udp(6)_lib_err_encap()
to confirm this path does need to be updated. For sctp, what we can
do here is check if the corresponding asoc and transport exist.
Note that icmp packet process for sctp over udp is done by udp sock
.encap_err_lookup(), and it means for now we can't do as much as
sctp_v4/6_err() does. Also we can't do the two mappings mentioned
in rfc6951#section-5.5.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch is to add the udp6 sock part in sctp_udp_sock_start/stop().
udp_conf.use_udp6_rx_checksums is set to true, as:
"The SCTP checksum MUST be computed for IPv4 and IPv6, and the UDP
checksum SHOULD be computed for IPv4 and IPv6"
says in rfc6951#section-5.3.
v1->v2:
- Add pr_err() when fails to create udp v6 sock.
- Add #if IS_ENABLED(CONFIG_IPV6) not to create v6 sock when ipv6 is
disabled.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch is to add the functions to create/release udp4 sock,
and set the sock's encap_rcv to process the incoming udp encap
sctp packets. In sctp_udp_rcv(), as we can see, all we need to
do is fix the transport header for sctp_rcv(), then it would
implement the part of rfc6951#section-5.4:
"When an encapsulated packet is received, the UDP header is removed.
Then, the generic lookup is performed, as done by an SCTP stack
whenever a packet is received, to find the association for the
received SCTP packet"
Note that these functions will be called in the last patch of
this patchset when enabling this feature.
v1->v2:
- Add pr_err() when fails to create udp v4 sock.
v2->v3:
- Add 'select NET_UDP_TUNNEL' in sctp Kconfig.
v3->v4:
- No change.
v4->v5:
- Change to set udp_port to 0 by default.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
For the gso of sctp over udp packets, sctp_gso_segment() will be called in
skb_udp_tunnel_segment(), we need to set transport_header to sctp header.
As all the current HWs can't handle both crc checksum and udp checksum at
the same time, the crc checksum has to be done in sctp_gso_segment() by
removing the NETIF_F_SCTP_CRC flag from the features.
Meanwhile, if the HW can't do udp checksum, csum and csum_start has to be
set correctly, and udp checksum will be done in __skb_udp_tunnel_segment()
by calling gso_make_checksum().
Thanks to Paolo, Marcelo and Guillaume for helping with this one.
v1->v2:
- no change.
v2->v3:
- remove the he NETIF_F_SCTP_CRC flag from the features.
- set csum and csum_start in sctp_gso_make_checksum().
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Small conflict around locking in rxrpc_process_event() -
channel_lock moved to bundle in next, while state lock
needs _bh() from net.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Two minor conflicts:
1) net/ipv4/route.c, adding a new local variable while
moving another local variable and removing it's
initial assignment.
2) drivers/net/dsa/microchip/ksz9477.c, overlapping changes.
One pretty prints the port mode differently, whilst another
changes the driver to try and obtain the port mode from
the port node rather than the switch node.
Signed-off-by: David S. Miller <davem@davemloft.net>
When calculating ancestor_size with IPv6 enabled, simply using
sizeof(struct ipv6_pinfo) doesn't account for extra bytes needed for
alignment in the struct sctp6_sock. On x86, there aren't any extra
bytes, but on ARM the ipv6_pinfo structure is aligned on an 8-byte
boundary so there were 4 pad bytes that were omitted from the
ancestor_size calculation. This would lead to corruption of the
pd_lobby pointers, causing an oops when trying to free the sctp
structure on socket close.
Fixes: 636d25d557 ("sctp: not copy sctp_sock pd_lobby in sctp_copy_descendant")
Signed-off-by: Henry Ptasinski <hptasinski@google.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We got slightly different patches removing a double word
in a comment in net/ipv4/raw.c - picked the version from net.
Simple conflict in drivers/net/ethernet/ibm/ibmvnic.c. Use cached
values instead of VNIC login response buffer (following what
commit 507ebe6444 ("ibmvnic: Fix use-after-free of VNIC login
response buffer") did).
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pull networking fixes from David Miller:
1) Use netif_rx_ni() when necessary in batman-adv stack, from Jussi
Kivilinna.
2) Fix loss of RTT samples in rxrpc, from David Howells.
3) Memory leak in hns_nic_dev_probe(), from Dignhao Liu.
4) ravb module cannot be unloaded, fix from Yuusuke Ashizuka.
5) We disable BH for too lokng in sctp_get_port_local(), add a
cond_resched() here as well, from Xin Long.
6) Fix memory leak in st95hf_in_send_cmd, from Dinghao Liu.
7) Out of bound access in bpf_raw_tp_link_fill_link_info(), from
Yonghong Song.
8) Missing of_node_put() in mt7530 DSA driver, from Sumera
Priyadarsini.
9) Fix crash in bnxt_fw_reset_task(), from Michael Chan.
10) Fix geneve tunnel checksumming bug in hns3, from Yi Li.
11) Memory leak in rxkad_verify_response, from Dinghao Liu.
12) In tipc, don't use smp_processor_id() in preemptible context. From
Tuong Lien.
13) Fix signedness issue in mlx4 memory allocation, from Shung-Hsi Yu.
14) Missing clk_disable_prepare() in gemini driver, from Dan Carpenter.
15) Fix ABI mismatch between driver and firmware in nfp, from Louis
Peens.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (110 commits)
net/smc: fix sock refcounting in case of termination
net/smc: reset sndbuf_desc if freed
net/smc: set rx_off for SMCR explicitly
net/smc: fix toleration of fake add_link messages
tg3: Fix soft lockup when tg3_reset_task() fails.
doc: net: dsa: Fix typo in config code sample
net: dp83867: Fix WoL SecureOn password
nfp: flower: fix ABI mismatch between driver and firmware
tipc: fix shutdown() of connectionless socket
ipv6: Fix sysctl max for fib_multipath_hash_policy
drivers/net/wan/hdlc: Change the default of hard_header_len to 0
net: gemini: Fix another missing clk_disable_unprepare() in probe
net: bcmgenet: fix mask check in bcmgenet_validate_flow()
amd-xgbe: Add support for new port mode
net: usb: dm9601: Add USB ID of Keenetic Plus DSL
vhost: fix typo in error message
net: ethernet: mlx4: Fix memory allocation in mlx4_buddy_init()
pktgen: fix error message with wrong function name
net: ethernet: ti: am65-cpsw: fix rmii 100Mbit link mode
cxgb4: fix thermal zone device registration
...
Drop the repeated word "an".
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Vlad Yasevich <vyasevich@gmail.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Cc: linux-sctp@vger.kernel.org
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drop the repeated words "for", "that", and "a".
Change "his" to "this".
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Vlad Yasevich <vyasevich@gmail.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Cc: linux-sctp@vger.kernel.org
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drop the repeated words "of" and "that".
Add some punctuation for readability.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Vlad Yasevich <vyasevich@gmail.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Cc: linux-sctp@vger.kernel.org
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drop the repeated word "the".
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Vlad Yasevich <vyasevich@gmail.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Cc: linux-sctp@vger.kernel.org
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drop the repeated word "of".
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Vlad Yasevich <vyasevich@gmail.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Cc: linux-sctp@vger.kernel.org
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drop the repeated word "the" and "now".
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Vlad Yasevich <vyasevich@gmail.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Cc: linux-sctp@vger.kernel.org
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drop the repeated word "the" in two places.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Vlad Yasevich <vyasevich@gmail.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Cc: linux-sctp@vger.kernel.org
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
With disabling bh in the whole sctp_get_port_local(), when
snum == 0 and too many ports have been used, the do-while
loop will take the cpu for a long time and cause cpu stuck:
[ ] watchdog: BUG: soft lockup - CPU#11 stuck for 22s!
[ ] RIP: 0010:native_queued_spin_lock_slowpath+0x4de/0x940
[ ] Call Trace:
[ ] _raw_spin_lock+0xc1/0xd0
[ ] sctp_get_port_local+0x527/0x650 [sctp]
[ ] sctp_do_bind+0x208/0x5e0 [sctp]
[ ] sctp_autobind+0x165/0x1e0 [sctp]
[ ] sctp_connect_new_asoc+0x355/0x480 [sctp]
[ ] __sctp_connect+0x360/0xb10 [sctp]
There's no need to disable bh in the whole function of
sctp_get_port_local. So fix this cpu stuck by removing
local_bh_disable() called at the beginning, and using
spin_lock_bh() instead.
The same thing was actually done for inet_csk_get_port() in
Commit ea8add2b19 ("tcp/dccp: better use of ephemeral
ports in bind()").
Thanks to Marcelo for pointing the buggy code out.
v1->v2:
- use cond_resched() to yield cpu to other tasks if needed,
as Eric noticed.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reported-by: Ying Xu <yinxu@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The number of output and input streams was never being reduced, eg when
processing received INIT or INIT_ACK chunks.
The effect is that DATA chunks can be sent with invalid stream ids
and then discarded by the remote system.
Fixes: 2075e50caf ("sctp: convert to genradix")
Signed-off-by: David Laight <david.laight@aculab.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As said by Linus:
A symmetric naming is only helpful if it implies symmetries in use.
Otherwise it's actively misleading.
In "kzalloc()", the z is meaningful and an important part of what the
caller wants.
In "kzfree()", the z is actively detrimental, because maybe in the
future we really _might_ want to use that "memfill(0xdeadbeef)" or
something. The "zero" part of the interface isn't even _relevant_.
The main reason that kzfree() exists is to clear sensitive information
that should not be leaked to other future users of the same memory
objects.
Rename kzfree() to kfree_sensitive() to follow the example of the recently
added kvfree_sensitive() and make the intention of the API more explicit.
In addition, memzero_explicit() is used to clear the memory to make sure
that it won't get optimized away by the compiler.
The renaming is done by using the command sequence:
git grep -w --name-only kzfree |\
xargs sed -i 's/kzfree/kfree_sensitive/'
followed by some editing of the kfree_sensitive() kerneldoc and adding
a kzfree backward compatibility macro in slab.h.
[akpm@linux-foundation.org: fs/crypto/inline_crypt.c needs linux/slab.h]
[akpm@linux-foundation.org: fix fs/crypto/inline_crypt.c some more]
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: David Howells <dhowells@redhat.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Cc: James Morris <jmorris@namei.org>
Cc: "Serge E. Hallyn" <serge@hallyn.com>
Cc: Joe Perches <joe@perches.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: "Jason A . Donenfeld" <Jason@zx2c4.com>
Link: http://lkml.kernel.org/r/20200616154311.12314-3-longman@redhat.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The UDP reuseport conflict was a little bit tricky.
The net-next code, via bpf-next, extracted the reuseport handling
into a helper so that the BPF sk lookup code could invoke it.
At the same time, the logic for reuseport handling of unconnected
sockets changed via commit efc6b6f6c3
which changed the logic to carry on the reuseport result into the
rest of the lookup loop if we do not return immediately.
This requires moving the reuseport_has_conns() logic into the callers.
While we are here, get rid of inline directives as they do not belong
in foo.c files.
The other changes were cases of more straightforward overlapping
modifications.
Signed-off-by: David S. Miller <davem@davemloft.net>
The variable status is being initialized with a value that is never read
and it is being updated later with a new value. The initialization is
redundant and can be removed. Also put the variable declarations into
reverse christmas tree order.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This sockopt accepts two kinds of parameters, using struct
sctp_sack_info and struct sctp_assoc_value. The mentioned commit didn't
notice an implicit cast from the smaller (latter) struct to the bigger
one (former) when copying the data from the user space, which now leads
to an attempt to write beyond the buffer (because it assumes the storing
buffer is bigger than the parameter itself).
Fix it by allocating a sctp_sack_info on stack and filling it out based
on the small struct for the compat case.
Changelog stole from an earlier patch from Marcelo Ricardo Leitner.
Fixes: ebb25defdc ("sctp: pass a kernel pointer to sctp_setsockopt_delayed_ack")
Reported-by: syzbot+0e4699d000d8b874d8dc@syzkaller.appspotmail.com
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rework the remaining setsockopt code to pass a sockptr_t instead of a
plain user pointer. This removes the last remaining set_fs(KERNEL_DS)
outside of architecture specific code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Stefan Schmidt <stefan@datenfreihafen.org> [ieee802154]
Acked-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When adding a stream with stream reconf, the new stream firstly is in
CLOSED state but new out chunks can still be enqueued. Then once gets
the confirmation from the peer, the state will change to OPEN.
However, if the peer denies, it needs to roll back the stream. But when
doing that, it only sets the stream outcnt back, and the chunks already
in the new stream don't get purged. It caused these chunks can still be
dequeued in sctp_outq_dequeue_data().
As its stream is still in CLOSE, the chunk will be enqueued to the head
again by sctp_outq_head_data(). This chunk will never be sent out, and
the chunks after it can never be dequeued. The assoc will be 'hung' in
a dead loop of sending this chunk.
To fix it, this patch is to purge these chunks already in the new
stream by calling sctp_stream_shrink_out() when failing to do the
addstream reconf.
Fixes: 11ae76e67a ("sctp: implement receiver-side procedures for the Reconf Response Parameter")
Reported-by: Ying Xu <yinxu@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's not necessary to go list_for_each for outq->out_chunk_list
when new outcnt >= old outcnt, as no chunk with higher sid than
new (outcnt - 1) exists in the outqueue.
While at it, also move the list_for_each code in a new function
sctp_stream_shrink_out(), which will be used in the next patch.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is just used once, and a direct return for the redirect to the AF
case is much easier to follow than jumping to the end of a very long
function.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer. Adapt sctp_setsockopt to use a
kzfree for this case.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch from kzfree to sctp_setsockopt_auth_key + kfree to prepare for
moving the kfree to common code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename sctp_setsockopt_bindx_kernel back to sctp_setsockopt_bindx,
and use the kernel pointer that sctp_setsockopt has available instead of
directly handling the user pointer in the old sctp_setsockopt_bindx.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prepare for for moving the copy_from_user from the individual sockopts
to the main setsockopt helper. As of this commit the kopt variable
is not used yet, but the following commits will start using it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Handle the few cases that need special treatment in-line using
in_compat_syscall(). This also removes all the now unused
compat_{get,set}sockopt methods.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Handle the few cases that need special treatment in-line using
in_compat_syscall().
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the compat handling to sock_common_{get,set}sockopt instead,
keyed of in_compat_syscall(). This allow to remove the now unused
->compat_{get,set}sockopt methods from struct proto_ops.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Acked-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a socket is set ipv6only, it will still send IPv4 addresses in the
INIT and INIT_ACK packets. This potentially misleads the peer into using
them, which then would cause association termination.
The fix is to not add IPv4 addresses to ipv6only sockets.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reported-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Tested-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 84af7a6194 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.
This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.
There are a variety of indentation styles found.
a) 4 spaces + '---help---'
b) 7 spaces + '---help---'
c) 8 spaces + '---help---'
d) 1 space + 1 tab + '---help---'
e) 1 tab + '---help---' (correct indentation)
f) 1 tab + 1 space + '---help---'
g) 1 tab + 2 spaces + '---help---'
In order to convert all of them to 1 tab + 'help', I ran the
following commend:
$ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Pull networking updates from David Miller:
1) Allow setting bluetooth L2CAP modes via socket option, from Luiz
Augusto von Dentz.
2) Add GSO partial support to igc, from Sasha Neftin.
3) Several cleanups and improvements to r8169 from Heiner Kallweit.
4) Add IF_OPER_TESTING link state and use it when ethtool triggers a
device self-test. From Andrew Lunn.
5) Start moving away from custom driver versions, use the globally
defined kernel version instead, from Leon Romanovsky.
6) Support GRO vis gro_cells in DSA layer, from Alexander Lobakin.
7) Allow hard IRQ deferral during NAPI, from Eric Dumazet.
8) Add sriov and vf support to hinic, from Luo bin.
9) Support Media Redundancy Protocol (MRP) in the bridging code, from
Horatiu Vultur.
10) Support netmap in the nft_nat code, from Pablo Neira Ayuso.
11) Allow UDPv6 encapsulation of ESP in the ipsec code, from Sabrina
Dubroca. Also add ipv6 support for espintcp.
12) Lots of ReST conversions of the networking documentation, from Mauro
Carvalho Chehab.
13) Support configuration of ethtool rxnfc flows in bcmgenet driver,
from Doug Berger.
14) Allow to dump cgroup id and filter by it in inet_diag code, from
Dmitry Yakunin.
15) Add infrastructure to export netlink attribute policies to
userspace, from Johannes Berg.
16) Several optimizations to sch_fq scheduler, from Eric Dumazet.
17) Fallback to the default qdisc if qdisc init fails because otherwise
a packet scheduler init failure will make a device inoperative. From
Jesper Dangaard Brouer.
18) Several RISCV bpf jit optimizations, from Luke Nelson.
19) Correct the return type of the ->ndo_start_xmit() method in several
drivers, it's netdev_tx_t but many drivers were using
'int'. From Yunjian Wang.
20) Add an ethtool interface for PHY master/slave config, from Oleksij
Rempel.
21) Add BPF iterators, from Yonghang Song.
22) Add cable test infrastructure, including ethool interfaces, from
Andrew Lunn. Marvell PHY driver is the first to support this
facility.
23) Remove zero-length arrays all over, from Gustavo A. R. Silva.
24) Calculate and maintain an explicit frame size in XDP, from Jesper
Dangaard Brouer.
25) Add CAP_BPF, from Alexei Starovoitov.
26) Support terse dumps in the packet scheduler, from Vlad Buslov.
27) Support XDP_TX bulking in dpaa2 driver, from Ioana Ciornei.
28) Add devm_register_netdev(), from Bartosz Golaszewski.
29) Minimize qdisc resets, from Cong Wang.
30) Get rid of kernel_getsockopt and kernel_setsockopt in order to
eliminate set_fs/get_fs calls. From Christoph Hellwig.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2517 commits)
selftests: net: ip_defrag: ignore EPERM
net_failover: fixed rollback in net_failover_open()
Revert "tipc: Fix potential tipc_aead refcnt leak in tipc_crypto_rcv"
Revert "tipc: Fix potential tipc_node refcnt leak in tipc_rcv"
vmxnet3: allow rx flow hash ops only when rss is enabled
hinic: add set_channels ethtool_ops support
selftests/bpf: Add a default $(CXX) value
tools/bpf: Don't use $(COMPILE.c)
bpf, selftests: Use bpf_probe_read_kernel
s390/bpf: Use bcr 0,%0 as tail call nop filler
s390/bpf: Maintain 8-byte stack alignment
selftests/bpf: Fix verifier test
selftests/bpf: Fix sample_cnt shared between two threads
bpf, selftests: Adapt cls_redirect to call csum_level helper
bpf: Add csum_level helper for fixing up csum levels
bpf: Fix up bpf_skb_adjust_room helper's skb csum setting
sfc: add missing annotation for efx_ef10_try_update_nic_stats_vf()
crypto/chtls: IPv6 support for inline TLS
Crypto/chcr: Fixes a coccinile check error
Crypto/chcr: Fixes compilations warnings
...
Pull crypto updates from Herbert Xu:
"API:
- Introduce crypto_shash_tfm_digest() and use it wherever possible.
- Fix use-after-free and race in crypto_spawn_alg.
- Add support for parallel and batch requests to crypto_engine.
Algorithms:
- Update jitter RNG for SP800-90B compliance.
- Always use jitter RNG as seed in drbg.
Drivers:
- Add Arm CryptoCell driver cctrng.
- Add support for SEV-ES to the PSP driver in ccp"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (114 commits)
crypto: hisilicon - fix driver compatibility issue with different versions of devices
crypto: engine - do not requeue in case of fatal error
crypto: cavium/nitrox - Fix a typo in a comment
crypto: hisilicon/qm - change debugfs file name from qm_regs to regs
crypto: hisilicon/qm - add DebugFS for xQC and xQE dump
crypto: hisilicon/zip - add debugfs for Hisilicon ZIP
crypto: hisilicon/hpre - add debugfs for Hisilicon HPRE
crypto: hisilicon/sec2 - add debugfs for Hisilicon SEC
crypto: hisilicon/qm - add debugfs to the QM state machine
crypto: hisilicon/qm - add debugfs for QM
crypto: stm32/crc32 - protect from concurrent accesses
crypto: stm32/crc32 - don't sleep in runtime pm
crypto: stm32/crc32 - fix multi-instance
crypto: stm32/crc32 - fix run-time self test issue.
crypto: stm32/crc32 - fix ext4 chksum BUG_ON()
crypto: hisilicon/zip - Use temporary sqe when doing work
crypto: hisilicon - add device error report through abnormal irq
crypto: hisilicon - remove codes of directly report device errors through MSI
crypto: hisilicon - QM memory management optimization
crypto: hisilicon - unify initial value assignment into QM
...
xdp_umem.c had overlapping changes between the 64-bit math fix
for the calculation of npgs and the removal of the zerocopy
memory type which got rid of the chunk_size_nohdr member.
The mlx5 Kconfig conflict is a case where we just take the
net-next copy of the Kconfig entry dependency as it takes on
the ESWITCH dependency by one level of indirection which is
what the 'net' conflicting change is trying to ensure.
Signed-off-by: David S. Miller <davem@davemloft.net>
The SCTP protocol allows to bind multiple address to a socket. That
feature is currently only exposed as a socket option. Add a bind_add
method struct proto that allows to bind additional addresses, and
switch the dlm code to use the method instead of going through the
socket option from kernel space.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split out a sctp_setsockopt_bindx_kernel that takes a kernel pointer
to the sockaddr and make sctp_setsockopt_bindx a small wrapper around
it. This prepares for adding a new bind_add proto op.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure SCTP_ADDR_{MADE_PRIM,ADDED} are sent only for associations
that have been established.
These events are described in rfc6458#section-6.1
SCTP_PEER_ADDR_CHANGE:
This tag indicates that an address that is
part of an existing association has experienced a change of
state (e.g., a failure or return to service of the reachability
of an endpoint via a specific transport address).
Signed-off-by: Jonas Falkevik <jonas.falkevik@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
change typo in function name "nofity" to "notify"
sctp_ulpevent_nofity_peer_addr_change ->
sctp_ulpevent_notify_peer_addr_change
Signed-off-by: Jonas Falkevik <jonas.falkevik@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change 'handeled' to 'handled' in the Kconfig help for SCTP.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MSCC bug fix in 'net' had to be slightly adjusted because the
register accesses are done slightly differently in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit bdf6fa52f0 ("sctp: handle association restarts when the
socket is closed.") starts shutdown when an association is restarted,
if in SHUTDOWN-PENDING state and the socket is closed. However, the
rationale stated in that commit applies also when in SHUTDOWN-SENT
state - we don't want to move an association to ESTABLISHED state when
the socket has been closed, because that results in an association
that is unreachable from user space.
The problem scenario:
1. Client crashes and/or restarts.
2. Server (using one-to-one socket) calls close(). SHUTDOWN is lost.
3. Client reconnects using the same addresses and ports.
4. Server's association is restarted. The association and the socket
move to ESTABLISHED state, even though the server process has
closed its descriptor.
Also, after step 4 when the server process exits, some resources are
leaked in an attempt to release the underlying inet sock structure in
ESTABLISHED state:
IPv4: Attempt to release TCP socket in state 1 00000000377288c7
Fix by acting the same way as in SHUTDOWN-PENDING state. That is, if
an association is restarted in SHUTDOWN-SENT state and the socket is
closed, then start shutdown and don't move the association or the
socket to ESTABLISHED state.
Fixes: bdf6fa52f0 ("sctp: handle association restarts when the socket is closed.")
Signed-off-by: Jere Leppänen <jere.leppanen@nokia.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This BUG halt was reported a while back, but the patch somehow got
missed:
PID: 2879 TASK: c16adaa0 CPU: 1 COMMAND: "sctpn"
#0 [f418dd28] crash_kexec at c04a7d8c
#1 [f418dd7c] oops_end at c0863e02
#2 [f418dd90] do_invalid_op at c040aaca
#3 [f418de28] error_code (via invalid_op) at c08631a5
EAX: f34baac0 EBX: 00000090 ECX: f418deb0 EDX: f5542950 EBP: 00000000
DS: 007b ESI: f34ba800 ES: 007b EDI: f418dea0 GS: 00e0
CS: 0060 EIP: c046fa5e ERR: ffffffff EFLAGS: 00010286
#4 [f418de5c] add_timer at c046fa5e
#5 [f418de68] sctp_do_sm at f8db8c77 [sctp]
#6 [f418df30] sctp_primitive_SHUTDOWN at f8dcc1b5 [sctp]
#7 [f418df48] inet_shutdown at c080baf9
#8 [f418df5c] sys_shutdown at c079eedf
#9 [f418df70] sys_socketcall at c079fe88
EAX: ffffffda EBX: 0000000d ECX: bfceea90 EDX: 0937af98
DS: 007b ESI: 0000000c ES: 007b EDI: b7150ae4
SS: 007b ESP: bfceea7c EBP: bfceeaa8 GS: 0033
CS: 0073 EIP: b775c424 ERR: 00000066 EFLAGS: 00000282
It appears that the side effect that starts the shutdown timer was processed
multiple times, which can happen as multiple paths can trigger it. This of
course leads to the BUG halt in add_timer getting called.
Fix seems pretty straightforward, just check before the timer is added if its
already been started. If it has mod the timer instead to min(current
expiration, new expiration)
Its been tested but not confirmed to fix the problem, as the issue has only
occured in production environments where test kernels are enjoined from being
installed. It appears to be a sane fix to me though. Also, recentely,
Jere found a reproducer posted on list to confirm that this resolves the
issues
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Vlad Yasevich <vyasevich@gmail.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: jere.leppanen@nokia.com
CC: marcelo.leitner@gmail.com
CC: netdev@vger.kernel.org
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To prepare removing the global routing_ioctl hack start lifting the code
into a newly added ipv6 ->compat_ioctl handler.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of manually allocating a 'struct shash_desc' on the stack and
calling crypto_shash_digest(), switch to using the new helper function
crypto_shash_tfm_digest() which does this for us.
Cc: linux-sctp@vger.kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pull in Christoph Hellwig's series that changes the sysctl's ->proc_handler
methods to take kernel pointers instead. It gets rid of the set_fs address
space overrides used by BPF. As per discussion, pull in the feature branch
into bpf-next as it relates to BPF sysctl progs.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20200427071508.GV23230@ZenIV.linux.org.uk/T/
Instead of having all the sysctl handlers deal with user pointers, which
is rather hairy in terms of the BPF interaction, copy the input to and
from userspace in common code. This also means that the strings are
always NUL-terminated by the common code, making the API a little bit
safer.
As most handler just pass through the data to one of the common handlers
a lot of the changes are mechnical.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Andrey Ignatov <rdna@fb.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
