sd_set_power_mode() in derived module drivers/mmc/host/rtsx_usb_sdmmc.c
acquires dev_mutex and then calls pm_runtime_get_sync() to make sure the
device is awake while initializing a newly inserted card. Once it is
called during suspending state and explicitly before rtsx_usb_suspend()
acquires the same dev_mutex, both routine deadlock and further hang the
driver because pm_runtime_get_sync() waits the pending PM operations.
Fix this by using an empty suspend method. mmc_core always turns the
LED off after a request is done and thus it is ok to remove the only
rtsx_usb_turn_off_led() here.
Cc: <stable@vger.kernel.org> # v3.16+
Fixes: 730876be25 ("mfd: Add realtek USB card reader driver")
Signed-off-by: Roger Tseng <rogerable@realtek.com>
[Lee: Removed newly unused variable]
Signed-off-by: Lee Jones <lee.jones@linaro.org>
If we don't tell regmap-irq that our first status
register is at offset 1, it will try to read offset
zero, which is the chipid register.
Fixes: 44b4dc6 mfd: tps65218: Add driver for the TPS65218 PMIC
Cc: <stable@vger.kernel.org> # v3.15+
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
STATUS register can be modified by the HW, so we
should bypass cache because of that.
In the case of INT[12] registers, they are the ones
that actually clear the IRQ source at the time they
are read. If we rely on the cache for them, we will
never be able to clear the interrupt, which will cause
our IRQ line to be disabled due to IRQ throttling.
Fixes: 44b4dc6 mfd: tps65218: Add driver for the TPS65218 PMIC
Cc: <stable@vger.kernel.org> # v3.15+
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Allow multiple DA9052 regulators be registered by registering with
PLATFORM_DEVID_AUTO instead of PLATFORM_DEVID_NONE.
The subdevices are currently registered with PLATFORM_DEVID_NONE, which
will cause a name collision on the platform bus when multiple regulators
are registered:
[ 0.128855] da9052-regulator da9052-regulator: invalid regulator ID specified
[ 0.128973] da9052-regulator: probe of da9052-regulator failed with error -22
[ 0.129148] ------------[ cut here ]------------
[ 0.129200] WARNING: CPU: 0 PID: 1 at fs/sysfs/dir.c:31 sysfs_warn_dup+0x5c/0x7c()
[ 0.129233] sysfs: cannot create duplicate filename '/devices/platform/soc/60000000.aips/63fc8000.i2c/i2c-0/0-0048/da9052-regulator
...
[ 0.132891] ------------[ cut here ]------------
[ 0.132924] WARNING: CPU: 0 PID: 1 at lib/kobject.c:240 kobject_add_internal+0x24c/0x2cc()
[ 0.132957] kobject_add_internal failed for da9052-regulator with -EEXIST, don't try to register things with the same name in the same directory.
...
[ 0.137000] da9052 0-0048: mfd_add_devices failed: -17
[ 0.138486] da9052: probe of 0-0048 failed with error -17
Based on the fix done by Johan Hovold at commit b668422872 ("mfd:
viperboard: Fix platform-device id collision").
Tested on a imx53-qsb board, where multiple DA9053 regulators can be
successfully probed.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
On 64-bit, relocation is not required unless the load address gets
changed. Without this, relocations do unexpected things when the kernel
is above 4G.
Reported-by: Baoquan He <bhe@redhat.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Tested-by: Thomas D. <whissi@whissi.de>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Jan Beulich <JBeulich@suse.com>
Cc: Junjie Mao <eternal.n08@gmail.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/20150116005146.GA4212@www.outflux.net
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
As dts files have been reorganised under vendor subdirs, dtb files
cannot be removed with "make distclean" now. Thus, this patch moves
dtb files under archclean rule and removes unnecessary entries.
Cc: Robert Richter <rrichter@cavium.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Jungseok Lee <jungseoklee85@gmail.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Xen overrides __acpi_register_gsi and leaves __acpi_unregister_gsi as is.
That means, an IRQ allocated by acpi_register_gsi_xen_hvm() or
acpi_register_gsi_xen() will be freed by acpi_unregister_gsi_ioapic(),
which may cause undesired effects. So override __acpi_unregister_gsi to
NULL for safety.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Tested-by: Sander Eikelenboom <linux@eikelenboom.it>
Cc: Tony Luck <tony.luck@intel.com>
Cc: xen-devel@lists.xenproject.org
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Graeme Gregory <graeme.gregory@linaro.org>
Cc: Lv Zheng <lv.zheng@intel.com>
Link: http://lkml.kernel.org/r/1421720467-7709-4-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Xen pciback driver assumes that pci_dev->irq won't change after calling
pci_disable_device(). But commit cffe0a2b5a
("x86, irq: Keep balance of IOAPIC pin reference count") frees irq
resources and resets pci_dev->irq to zero when pci_disable_device() is
called.
So this is a hotfix for 3.19 to avoid resetting pci_dev->irq, and
another proper fix will be prepared for next merging window.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Tested-by: Sander Eikelenboom <linux@eikelenboom.it>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Len Brown <lenb@kernel.org>
Link: http://lkml.kernel.org/r/1421720467-7709-3-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Currently Xen Domain0 has special treatment for ACPI SCI interrupt,
that is initialize irq for ACPI SCI at early stage in a special way as:
xen_init_IRQ()
->pci_xen_initial_domain()
->xen_setup_acpi_sci()
Allocate and initialize irq for ACPI SCI
Function xen_setup_acpi_sci() calls acpi_gsi_to_irq() to get an irq
number for ACPI SCI. But unfortunately acpi_gsi_to_irq() depends on
IOAPIC irqdomains through following path
acpi_gsi_to_irq()
->mp_map_gsi_to_irq()
->mp_map_pin_to_irq()
->check IOAPIC irqdomain
For PV domains, it uses Xen event based interrupt manangement and
doesn't make uses of native IOAPIC, so no irqdomains created for IOAPIC.
This causes Xen domain0 fail to install interrupt handler for ACPI SCI
and all ACPI events will be lost. Please refer to:
https://lkml.org/lkml/2014/12/19/178
So the fix is to get rid of special treatment for ACPI SCI, just treat
ACPI SCI as normal GSI interrupt as:
acpi_gsi_to_irq()
->acpi_register_gsi()
->acpi_register_gsi_xen()
->xen_register_gsi()
With above change, there's no need for xen_setup_acpi_sci() anymore.
The above change also works with bare metal kernel too.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Tested-by: Sander Eikelenboom <linux@eikelenboom.it>
Cc: Tony Luck <tony.luck@intel.com>
Cc: xen-devel@lists.xenproject.org
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Len Brown <len.brown@intel.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Link: http://lkml.kernel.org/r/1421720467-7709-2-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
- Fix two deadlocks around the pin control mutexes,
a long-standing issue that manifest itself in
plug/unplug of pin controllers. (Tagged for stable.)
- Handle an error path with zero functions in the
Qualcomm pin controller.
- Drop a bogus second GPIO chip added in the Lantiq
driver.
- Fix sudden IRQ loss on Rockchip pin controllers.
- Register the GIT tree in MAINTAINERS.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=YGym
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v3.19-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
"Here is a (hopefully final) slew of pin control fixes for the v3.19
series. The deadlock fix is kind of serious and tagged for stable,
the rest is business as usual.
- Fix two deadlocks around the pin control mutexes, a long-standing
issue that manifest itself in plug/unplug of pin controllers.
(Tagged for stable.)
- Handle an error path with zero functions in the Qualcomm pin
controller.
- Drop a bogus second GPIO chip added in the Lantiq driver.
- Fix sudden IRQ loss on Rockchip pin controllers.
- Register the GIT tree in MAINTAINERS"
* tag 'pinctrl-v3.19-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: MAINTAINERS: add git tree reference
pinctrl: qcom: Don't iterate past end of function array
pinctrl: lantiq: remove bogus of_gpio_chip_add
pinctrl: Fix two deadlocks
pinctrl: rockchip: Avoid losing interrupts when supporting both edges
Convert file->f_dentry->d_inode to file_inode() so as to get layered
filesystems right.
Found with: git grep '[.>]f_dentry'
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
This can happen if a multipathed device uses DIX and another path is
added via an adapter that does not support it. Multipath should not
allow this path to be added, but we should not depend upon that to avoid
crashing.
Signed-off-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Currently PWM functionality is broken on mx25 due to the wrong assignment of the
PWM "per" clock.
According to Documentation/devicetree/bindings/clock/imx25-clock.txt:
pwm_ipg_per 52
,so update the pwm "per" to use 'pwm_ipg_per' instead of 'per10' clock.
With this change PWM can work fine on mx25.
Cc: <stable@vger.kernel.org>
Reported-by: Carlos Soto <csotoalonso@gmail.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Pull networking fixes from David Miller:
1) Socket addresses returned in the error queue need to be fully
initialized before being passed on to userspace, fix from Willem de
Bruijn.
2) Interrupt handling fixes to davinci_emac driver from Tony Lindgren.
3) Fix races between receive packet steering and cpu hotplug, from Eric
Dumazet.
4) Allowing netlink sockets to subscribe to unknown multicast groups
leads to crashes, don't allow it. From Johannes Berg.
5) One to many socket races in SCTP fixed by Daniel Borkmann.
6) Put in a guard against the mis-use of ipv6 atomic fragments, from
Hagen Paul Pfeifer.
7) Fix promisc mode and ethtool crashes in sh_eth driver, from Ben
Hutchings.
8) NULL deref and double kfree fix in sxgbe driver from Girish K.S and
Byungho An.
9) cfg80211 deadlock fix from Arik Nemtsov.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (36 commits)
s2io: use snprintf() as a safety feature
r8152: remove sram_read
r8152: remove generic_ocp_read before writing
bgmac: activate irqs only if there is nothing to poll
bgmac: register napi before the device
sh_eth: Fix ethtool operation crash when net device is down
sh_eth: Fix promiscuous mode on chips without TSU
ipv6: stop sending PTB packets for MTU < 1280
net: sctp: fix race for one-to-many sockets in sendmsg's auto associate
genetlink: synchronize socket closing and family removal
genetlink: disallow subscribing to unknown mcast groups
genetlink: document parallel_ops
net: rps: fix cpu unplug
net: davinci_emac: Add support for emac on dm816x
net: davinci_emac: Fix ioremap for devices with MDIO within the EMAC address space
net: davinci_emac: Fix incomplete code for getting the phy from device tree
net: davinci_emac: Free clock after checking the frequency
net: davinci_emac: Fix runtime pm calls for davinci_emac
net: davinci_emac: Fix hangs with interrupts
ip: zero sockaddr returned on error queue
...
Pull crypto fix from Herbert Xu:
"This fixes a regression that arose from the change to add a crypto
prefix to module names which was done to prevent the loading of
arbitrary modules through the Crypto API.
In particular, a number of modules were missing the crypto prefix
which meant that they could no longer be autoloaded"
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: add missing crypto module aliases
The kallsyms routines (module_symbol_name, lookup_module_* etc) disable
preemption to walk the modules rather than taking the module_mutex:
this is because they are used for symbol resolution during oopses.
This works because there are synchronize_sched() and synchronize_rcu()
in the unload and failure paths. However, there's one case which doesn't
have that: the normal case where module loading succeeds, and we free
the init section.
We don't want a synchronize_rcu() there, because it would slow down
module loading: this bug was introduced in 2009 to speed module
loading in the first place.
Thus, we want to do the free in an RCU callback. We do this in the
simplest possible way by allocating a new rcu_head: if we put it in
the module structure we'd have to worry about that getting freed.
Reported-by: Rui Xiang <rui.xiang@huawei.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Nothing needs the module pointer any more, and the next patch will
call it from RCU, where the module itself might no longer exist.
Removing the arg is the safest approach.
This just codifies the use of the module_alloc/module_free pattern
which ftrace and bpf use.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Chris Metcalf <cmetcalf@ezchip.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: x86@kernel.org
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: linux-cris-kernel@axis.com
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: nios2-dev@lists.rocketboards.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: sparclinux@vger.kernel.org
Cc: netdev@vger.kernel.org
Archs have been abusing module_free() to clean up their arch-specific
allocations. Since module_free() is also (ab)used by BPF and trace code,
let's keep it to simple allocations, and provide a hook called before
that.
This means that avr32, ia64, parisc and s390 no longer need to implement
their own module_free() at all. avr32 doesn't need module_finalize()
either.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Chris Metcalf <cmetcalf@ezchip.com>
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-ia64@vger.kernel.org
Cc: linux-parisc@vger.kernel.org
Cc: linux-s390@vger.kernel.org
ignore_lockdep is uninitialized, and sysfs_attr_init() doesn't initialize
it, so memset to 0.
Reported-by: Huang Ying <ying.huang@intel.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
"sp->desc[i]" has 25 characters. "dev->name" has 15 characters. If we
used all 15 characters then the sprintf() would overflow.
I changed the "sprintf(sp->name, "%s Neterion %s"" to snprintf(), as
well, even though it can't overflow just to be consistent.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The legacy interrupts on omap4 got broken when gic got changed to
use irq_domain_add_linear() instead of the irq_domain_add_legacy(). We
still have the hardcoded legacy IRQ numbers in use in several places,
most notably the in the legacy DMA. It took a while to figure out
what the problem was and how it should be fixed for the -rc series.
Also include is a regression fix for the dra7 dwc3 suspend.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=lpO3
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.19/gic-regression-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Merge "Urgent omap4 legacy interrupt regression fix for v3.19-rc series" from
Tony Lindgren:
A rather urgent pull request to fix omap4 legacy interrupts.
The legacy interrupts on omap4 got broken when gic got changed to
use irq_domain_add_linear() instead of the irq_domain_add_legacy(). We
still have the hardcoded legacy IRQ numbers in use in several places,
most notably the in the legacy DMA. It took a while to figure out
what the problem was and how it should be fixed for the -rc series.
Also include is a regression fix for the dra7 dwc3 suspend.
* tag 'omap-for-v3.19/gic-regression-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP: Work around hardcoded interrupts
arm: boot: dts: dra7: enable dwc3 suspend PHY quirk
Signed-off-by: Olof Johansson <olof@lixom.net>
On Armada XP, 375 and 38x the MBus window 13 has the remap capability,
like windows 0 to 7. However, the mvebu-mbus driver isn't currently
taking into account this special case, which means that when window 13
is actually used, the remap registers are left to 0, making the device
using this MBus window unavailable.
As a minimal fix for stable, don't use window 13. A full fix will
follow later.
Fixes: fddddb52a6 ("bus: introduce an Marvell EBU MBus driver")
Cc: <stable@vger.kernel.org> # v3.10+
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Hayes Wang says:
====================
r8152: couldn't read OCP_SRAM_DATA
Read OCP_SRAM_DATA would read additional bytes and may let
the hw abnormal.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Read OCP register 0xa43a~0xa43b would clear some flags which the hw
would use, and it may let the device lost. However, the unit of
reading is 4 bytes. That is, it would read 0xa438~0xa43b when calling
sram_read() to read OCP_SRAM_DATA.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For ocp_write_word() and ocp_write_byte(), there is a generic_ocp_read()
which is used to read the whole 4 byte data, keep the unchanged bytes,
and modify the expected bytes. However, the "byen" could be used to
determine which bytes of the 4 bytes to write, so the action could be
removed.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Suppress the following warning displayed on building 32bit (i686) kernel.
===============================================================================
...
CC [M] fs/btrfs/extent_io.o
fs/btrfs/extent_io.c: In function ‘btrfs_free_io_failure_record’:
fs/btrfs/extent_io.c:2193:13: warning: cast to pointer from integer of
different size [-Wint-to-pointer-cast]
failrec = (struct io_failure_record *)state->private;
...
===============================================================================
Signed-off-by: Satoru Takeuchi <takeuchi_satoru@jp.fujitsu.com>
Reported-by: Chris Murphy <chris@colorremedies.com>
Signed-off-by: Chris Mason <clm@fb.com>
When removing a block group we were deleting it from its space_info's
ro_bgs list without the correct protection - the space info's spinlock.
Fix this by doing the list delete while holding the spinlock of the
corresponding space info, which is the correct lock for any operation
on that list.
This issue was introduced in the 3.19 kernel by the following change:
Btrfs: move read only block groups onto their own list V2
commit 633c0aad4c
I ran into a kernel crash while a task was running statfs, which iterates
the space_info->ro_bgs list while holding the space info's spinlock,
and another task was deleting it from the same list, without holding that
spinlock, as part of the block group remove operation (while running the
function btrfs_remove_block_group). This happened often when running the
stress test xfstests/generic/038 I recently made.
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Chris Mason <clm@fb.com>
The address that should be freed is not 'ppath' but 'path'.
Signed-off-by: Tsutomu Itoh <t-itoh@jp.fujitsu.com>
Reviewed-by: Miao Xie <miaoxie@huawei.com>
Signed-off-by: Chris Mason <clm@fb.com>
The version merged to 3.19 did not handle errors from start_trancaction
and could pass an invalid pointer to commit_transaction.
Fixes: 6b5fe46dfa ("btrfs: do commit in sync_fs if there are pending changes")
Reported-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Chris Mason <clm@fb.com>
Hauke Mehrtens says:
====================
bgmac: some fixes to napi usage
I compared the napi documentation with the bgmac driver and found some
problems in that driver. These two patches should fix the problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
IRQs should only get activated when there is nothing to poll in the
queue any more and to after every poll.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
napi should get registered before the netdev and not after.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings says:
====================
sh_eth fixes
I'm currently looking at Ethernet support on the R-Car H2 chip,
reviewing and testing the sh_eth driver. Here are fixes for two fairly
obvious bugs in the driver; I will probably have some more later.
These are not tested on any of the other supported chips.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver connects and disconnects the PHY device whenever the
net device is brought up and down. The ethtool get_settings,
set_settings and nway_reset operations will dereference a null
or dangling pointer if called while it is down.
I think it would be preferable to keep the PHY connected, but there
may be good reasons not to.
As an immediate fix for this bug:
- Set the phydev pointer to NULL after disconnecting the PHY
- Change those three operations to return -ENODEV while the PHY is
not connected
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently net_device_ops::set_rx_mode is only implemented for
chips with a TSU (multiple address table). However we do need
to turn the PRM (promiscuous) flag on and off for other chips.
- Remove the unlikely() from the TSU functions that we may safely
call for chips without a TSU
- Make setting of the MCT flag conditional on the tsu capability flag
- Rename sh_eth_set_multicast_list() to sh_eth_set_rx_mode() and plumb
it into both net_device_ops structures
- Remove the previously-unreachable branch in sh_eth_rx_mode() that
would otherwise reset the flags to defaults for non-TSU chips
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reduce the attack vector and stop generating IPv6 Fragment Header for
paths with an MTU smaller than the minimum required IPv6 MTU
size (1280 byte) - called atomic fragments.
See IETF I-D "Deprecating the Generation of IPv6 Atomic Fragments" [1]
for more information and how this "feature" can be misused.
[1] https://tools.ietf.org/html/draft-ietf-6man-deprecate-atomfrag-generation-00
Signed-off-by: Fernando Gont <fgont@si6networks.com>
Signed-off-by: Hagen Paul Pfeifer <hagen@jauu.net>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible for ata_sff_flush_pio_task() to set ap->hsm_task_state to
HSM_ST_IDLE in between the time __ata_sff_port_intr() checks for HSM_ST_IDLE
and before it calls ata_sff_hsm_move() causing ata_sff_hsm_move() to BUG().
This problem is hard to reproduce making this patch hard to verify, but this
fix will prevent the race.
I have not been able to reproduce the problem, but here is a crash dump from
a 2.6.32 kernel.
On examining the ata port's state, its hsm_task_state field has a value of HSM_ST_IDLE:
crash> struct ata_port.hsm_task_state ffff881c1121c000
hsm_task_state = 0
Normally, this should not be possible as ata_sff_hsm_move() was called from ata_sff_host_intr(),
which checks hsm_task_state and won't call ata_sff_hsm_move() if it has a HSM_ST_IDLE value.
PID: 11053 TASK: ffff8816e846cae0 CPU: 0 COMMAND: "sshd"
#0 [ffff88008ba03960] machine_kexec at ffffffff81038f3b
#1 [ffff88008ba039c0] crash_kexec at ffffffff810c5d92
#2 [ffff88008ba03a90] oops_end at ffffffff8152b510
#3 [ffff88008ba03ac0] die at ffffffff81010e0b
#4 [ffff88008ba03af0] do_trap at ffffffff8152ad74
#5 [ffff88008ba03b50] do_invalid_op at ffffffff8100cf95
#6 [ffff88008ba03bf0] invalid_op at ffffffff8100bf9b
[exception RIP: ata_sff_hsm_move+317]
RIP: ffffffff813a77ad RSP: ffff88008ba03ca0 RFLAGS: 00010097
RAX: 0000000000000000 RBX: ffff881c1121dc60 RCX: 0000000000000000
RDX: ffff881c1121dd10 RSI: ffff881c1121dc60 RDI: ffff881c1121c000
RBP: ffff88008ba03d00 R8: 0000000000000000 R9: 000000000000002e
R10: 000000000001003f R11: 000000000000009b R12: ffff881c1121c000
R13: 0000000000000000 R14: 0000000000000050 R15: ffff881c1121dd78
ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018
#7 [ffff88008ba03d08] ata_sff_host_intr at ffffffff813a7fbd
#8 [ffff88008ba03d38] ata_sff_interrupt at ffffffff813a821e
#9 [ffff88008ba03d78] handle_IRQ_event at ffffffff810e6ec0
--- <IRQ stack> ---
[exception RIP: pipe_poll+48]
RIP: ffffffff81192780 RSP: ffff880f26d459b8 RFLAGS: 00000246
RAX: 0000000000000000 RBX: ffff880f26d459c8 RCX: 0000000000000000
RDX: 0000000000000001 RSI: 0000000000000000 RDI: ffff881a0539fa80
RBP: ffffffff8100bb8e R8: ffff8803b23324a0 R9: 0000000000000000
R10: ffff880f26d45dd0 R11: 0000000000000008 R12: ffffffff8109b646
R13: ffff880f26d45948 R14: 0000000000000246 R15: 0000000000000246
ORIG_RAX: ffffffffffffff10 CS: 0010 SS: 0018
RIP: 00007f26017435c3 RSP: 00007fffe020c420 RFLAGS: 00000206
RAX: 0000000000000017 RBX: ffffffff8100b072 RCX: 00007fffe020c45c
RDX: 00007f2604a3f120 RSI: 00007f2604a3f140 RDI: 000000000000000d
RBP: 0000000000000000 R8: 00007fffe020e570 R9: 0101010101010101
R10: 0000000000000000 R11: 0000000000000246 R12: 00007fffe020e5f0
R13: 00007fffe020e5f4 R14: 00007f26045f373c R15: 00007fffe020e5e0
ORIG_RAX: 0000000000000017 CS: 0033 SS: 002b
Somewhere between the ata_sff_hsm_move() check and the ata_sff_host_intr() check, the value changed.
On examining the other cpus to see what else was running, another cpu was running the error handler
routines:
PID: 326 TASK: ffff881c11014aa0 CPU: 1 COMMAND: "scsi_eh_1"
#0 [ffff88008ba27e90] crash_nmi_callback at ffffffff8102fee6
#1 [ffff88008ba27ea0] notifier_call_chain at ffffffff8152d515
#2 [ffff88008ba27ee0] atomic_notifier_call_chain at ffffffff8152d57a
#3 [ffff88008ba27ef0] notify_die at ffffffff810a154e
#4 [ffff88008ba27f20] do_nmi at ffffffff8152b1db
#5 [ffff88008ba27f50] nmi at ffffffff8152aaa0
[exception RIP: _spin_lock_irqsave+47]
RIP: ffffffff8152a1ff RSP: ffff881c11a73aa0 RFLAGS: 00000006
RAX: 0000000000000001 RBX: ffff881c1121deb8 RCX: 0000000000000000
RDX: 0000000000000246 RSI: 0000000000000020 RDI: ffff881c122612d8
RBP: ffff881c11a73aa0 R8: ffff881c17083800 R9: 0000000000000000
R10: 0000000000000000 R11: 0000000000000000 R12: ffff881c1121c000
R13: 000000000000001f R14: ffff881c1121dd50 R15: ffff881c1121dc60
ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0000
--- <NMI exception stack> ---
#6 [ffff881c11a73aa0] _spin_lock_irqsave at ffffffff8152a1ff
#7 [ffff881c11a73aa8] ata_exec_internal_sg at ffffffff81396fb5
#8 [ffff881c11a73b58] ata_exec_internal at ffffffff81397109
#9 [ffff881c11a73bd8] atapi_eh_request_sense at ffffffff813a34eb
Before it tried to acquire a spinlock, ata_exec_internal_sg() called ata_sff_flush_pio_task().
This function will set ap->hsm_task_state to HSM_ST_IDLE, and has no locking around setting this
value. ata_sff_flush_pio_task() can then race with the interrupt handler and potentially set
HSM_ST_IDLE at a fatal moment, which will trigger a kernel BUG.
v2: Fixup comment in ata_sff_flush_pio_task()
tj: Further updated comment. Use ap->lock instead of shost lock and
use the [un]lock_irq variant instead of the irqsave/restore one.
Signed-off-by: David Milburn <dmilburn@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
Ronny reports: https://bugzilla.kernel.org/show_bug.cgi?id=87101
"Since commit 8a4aeec8d "libata/ahci: accommodate tag ordered
controllers" the access to the harddisk on the first SATA-port is
failing on its first access. The access to the harddisk on the
second port is working normal.
When reverting the above commit, access to both harddisks is working
fine again."
Maintain tag ordered submission as the default, but allow sata_sil24 to
continue with the old behavior.
Cc: <stable@vger.kernel.org>
Cc: Tejun Heo <tj@kernel.org>
Reported-by: Ronny Hegewald <Ronny.Hegewald@online.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Fixes a case where we call vmw_fifo_idle() from within a wait function with
task state !TASK_RUNNING, which is illegal.
In addition, make the locking fine-grained, so that it is performed once
for every read- and write operation. This is of course more costly, but we
don't perform much register access in the timing critical paths anyway. Instead
we have the extra benefit of being sure that we don't forget the hw lock around
register accesses. I think currently the kms code was quite buggy w r t this.
This fixes Red Hat Bugzilla Bug 1180796
Cc: stable@vger.kernel.org
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Jakob Bornecrantz <jakob@vmware.com>
Reference my pinctrl GIT tree @kernel.org
Reported-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Timur reports that this code crashes if nfunctions is 0. Fix the
loop iteration to only consider valid elements of the functions
array.
Reported-by: Timur Tabi <timur@codeaurora.org>
Cc: Pramod Gurav <pramod.gurav@smartplayin.com>
Cc: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Cc: Ivan T. Ivanov <iivanov@mm-sol.com>
Cc: Andy Gross <agross@codeaurora.org>
Fixes: 327455817a "pinctrl: qcom: Add support for reset for apq8064"
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
sparse complains about
include/trace/events/kvm.h:163:1: error: directive in argument list
include/trace/events/kvm.h:167:1: error: directive in argument list
include/trace/events/kvm.h:169:1: error: directive in argument list
and sparse is right. Preprocessing directives in an argument of a
macro are undefined behaviour as of C99 6.10.3p11.
Lets use an indirection to fix this.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Fixes a race condition in abort handling that was injected
when multiple interrupt support was added. When only a single
interrupt is present, the adapter guarantees it will send
responses for aborted commands prior to the response for the
abort command itself. With multiple interrupts, these responses
generally come back on different interrupts, so we need to
ensure the abort thread waits until the aborted command is
complete so we don't perform a double completion. This race
condition was being hit frequently in environments which
were triggering command timeouts, which was resulting in
a double completion causing a kernel oops.
Cc: <stable@vger.kernel.org>
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Reviewed-by: Wendy Xiong <wenxiong@linux.vnet.ibm.com>
Tested-by: Wendy Xiong <wenxiong@linux.vnet.ibm.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
It really needs to check that src is non-directory *and* use
{un,}lock_two_nodirectories(). As it is, it's trivial to cause
double-lock (ioctl(fd, CIFS_IOC_COPYCHUNK_FILE, fd)) and if the
last argument is an fd of directory, we are asking for trouble
by violating the locking order - all directories go before all
non-directories. If the last argument is an fd of parent
directory, it has 50% odds of locking child before parent,
which will cause AB-BA deadlock if we race with unlink().
Cc: stable@vger.kernel.org @ 3.13+
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
that have been around forever in the GPIO subsystem, most of them
also tagged for stable:
- A large slew of fixes from Johan Hovold who is finally testing and
reviewing the removal path of the GPIO drivers.
- Fix of_get_named_gpiod_flags() so it works as expected.
- Fix an IRQ handling bug in the crystalcove driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ekXq
-----END PGP SIGNATURE-----
Merge tag 'gpio-v3.19-4' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"Here is a set of fixes that mainly appeared when Johan Hovold started
exercising the removal path of the GPIO library, dealing with
hotplugging of GPIO controllers. Details from tag:
A slew of fixes dealing with some irritating bugs (non-regressions)
that have been around forever in the GPIO subsystem, most of them also
tagged for stable:
- A large slew of fixes from Johan Hovold who is finally testing and
reviewing the removal path of the GPIO drivers.
- Fix of_get_named_gpiod_flags() so it works as expected.
- Fix an IRQ handling bug in the crystalcove driver"
* tag 'gpio-v3.19-4' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpiolib: of: Correct error handling in of_get_named_gpiod_flags
gpio: sysfs: fix gpio attribute-creation race
gpio: sysfs: fix gpio device-attribute leak
gpio: sysfs: fix gpio-chip device-attribute leak
gpio: unregister gpiochip device before removing it
gpio: fix sleep-while-atomic in gpiochip_remove
gpio: fix memory leak and sleep-while-atomic
gpio: clean up gpiochip_add error handling
gpio: fix gpio-chip list corruption
gpio: fix memory and reference leaks in gpiochip_add error path
gpio: crystalcove: use handle_nested_irq
Pull input subsystem fixes from Dmitry Torokhov.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: uinput - fix ioctl nr overflow for UI_GET_SYSNAME/VERSION
Input: I8042 - add Acer Aspire 7738 to the nomux list
Input: elantech - support new ICs types for version 4
Input: i8042 - reset keyboard to fix Elantech touchpad detection
MAINTAINERS: remove Dmitry Torokhov's alternate address