Now that usb-storage has a target_alloc() routine, this patch (as1508)
moves some existing target-specific code out of the slave_alloc()
routine to where it really belongs.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1507) adds a skip_vpd_pages flag to struct scsi_device
and a no_report_luns flag to struct scsi_target. The first is used to
control whether sd will look at VPD pages for information on block
provisioning, limits, and characteristics. The second prevents
scsi_report_lun_scan() from issuing a REPORT LUNS command.
The patch also modifies usb-storage to set the new flag bits for all
USB devices and targets, and to stop adjusting the scsi_level value.
Historically we have seen that USB mass-storage devices often don't
support VPD pages or REPORT LUNS properly. Until now we have avoided
these things by setting the scsi_level to SCSI_2 for all USB devices.
But this has the side effect of storing the LUN bits into the second
byte of each CDB, and now we have a report of a device which doesn't
like that. The best solution is to stop abusing scsi_level and
instead have separate flags for VPD pages and REPORT LUNS.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Perry Wagle <wagle@mac.com>
CC: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Just run into the following:
- new disk arrived in the system
- udev couldn't wait to get its hands on to to run ata_id /dev/sda
- this sent the cdb 0xa1 to the device.
- my UAS-gadget recevied the cdb and had no idea what to do with it. It
decided to send a status URB back with sense set to invalid opcode.
- the host side received it status and completed the scsi command.
- the host sent another scsi with 4kib data buffer
- Now I was confused why the data transfer is only 512 bytes instead of
4kib since the host is always allocating the complete transfer in one
go.
- Finally the system crashed while walking through the sg list.
This patch adds three new flags in order to distinguish between DATA
URB completed and outstanding. If we receive status before data, we
cancel data and let data complete the command.
This solves the problem for IN and OUT transfers but does not work for
BIDI.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
The protocol specific structures and defines which are used by UAS are
moved into a header files by this patch so it can be accessed by the UAS
gadget as well.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
The UAS driver requires SG support by the HCD operating the device. This
patch stops UAS from operating on a HCD without sg support and prints a
message to let him know.
The spec says:
|For [USB2] backward compatibility, the device shall present [BOT] as
|alternate interface zero (primary) and [UAS] as alternate interface one
|(secondary). A device which does not need backward compatibility with
|[BOT] shall present [UAS] as alternate interface zero. In [USB2]
|systems, the [BOT] driver or an associated filter driver may need to
|issue a SET INTERFACE request for alternate interface one and then allow
|the [UAS] driver to load.
If the user used usb_modeswitch to switch to UAS then he can go back to
BOT or use a different HCD. In case UAS is the only interface then there
is currently no way out.
In future usb_sg_wait() should be extended to provide a non-blocking
interface so it can work with the UAS driver.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJO8x85AAoJEHuW6BYqjPXRXWgQAI/+xBuTNKwfe/zAcIYxH1I5
Lq3jQaaqZ/TYWMZH2BwHYPXLLayLpHyvYSmub4hJm9okPp/iWJeE6nnYg8Ige8CD
jmpGa8p25pvdP+Rn8GW0EVIA+X0ZVdUV1llz88+21piY4ydobBQOtUtXAIl5jsBv
EVjqCZ6kmn0X7utdutpTHQ421/5k/9x5bh7mHOQTLiMcouXDyA/KVYjet4DVt5PU
Umqrk+uOMUjnygShRZ3C+FLBi/cfJ2jKUQo34dJbhxtD4hZyDe3CXM0UKnvZ5dso
EAykudlN32L29vT000F5KCocEUjQfnqvlBKK+acI7gvdmHCerDn0X/luHx/skSQV
li+pqCqfcfnX6Xg68WWLod9xrt5TtUlD1vAwhvi+ObDIFcVkCqLIdD5lBl+pZz3s
L2j/NgxVkAEVr4VotCNCHCAw17nWYSyle7Px5rLzU1+gfRFTGXiepBxnp52ZPXFf
l+rM+U+OZzrEtuXQq2AEIqh07G4EeovEigWB2v0Eyl77ZmE+SprMHoFVLTtB5Xqc
iau4YMG3nuJdIEyxIHMTrIX91iEgKFfo2Zc030GIe1EH7Gllr8VSYnoQLZf6/tF7
D4NzlqAVQUd6RIDlwQn6XpOGm4FLMF0rJL+Di3QqZ1vk/CRfSmGPSP7mFLbaCNOg
YhMYuzWknxi80kYRMZgy
=GTUe
-----END PGP SIGNATURE-----
Merge tag 'uas_for_sarah' of git://linutronix.de/users/bigeasy/linux into for-uas-next
Merge UAS bug fixes from Sebastian Andrzej Siewior, including some patches of
mine that he signed.
UAS fixes for Sarah
Enable usb-storage support dynamic id again by using a fixed id entry
that describes a device using the Bulk-Only transport with the
Transparent SCSI protocol.
Signed-off-by: Huajun Li <huajun.li.lee@gmail.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Storage subdrivers, like alauda, datafab and others, don't support
dynamic id currently, and it needs lots of work but with very little
gain to enable the feature, so disable them in the patch.
Signed-off-by: Huajun Li <huajun.li.lee@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (53 commits)
Kconfig: acpi: Fix typo in comment.
misc latin1 to utf8 conversions
devres: Fix a typo in devm_kfree comment
btrfs: free-space-cache.c: remove extra semicolon.
fat: Spelling s/obsolate/obsolete/g
SCSI, pmcraid: Fix spelling error in a pmcraid_err() call
tools/power turbostat: update fields in manpage
mac80211: drop spelling fix
types.h: fix comment spelling for 'architectures'
typo fixes: aera -> area, exntension -> extension
devices.txt: Fix typo of 'VMware'.
sis900: Fix enum typo 'sis900_rx_bufer_status'
decompress_bunzip2: remove invalid vi modeline
treewide: Fix comment and string typo 'bufer'
hyper-v: Update MAINTAINERS
treewide: Fix typos in various parts of the kernel, and fix some comments.
clockevents: drop unknown Kconfig symbol GENERIC_CLOCKEVENTS_MIGR
gpio: Kconfig: drop unknown symbol 'CS5535_GPIO'
leds: Kconfig: Fix typo 'D2NET_V2'
sound: Kconfig: drop unknown symbol ARCH_CLPS7500
...
Fix up trivial conflicts in arch/powerpc/platforms/40x/Kconfig (some new
kconfig additions, close to removed commented-out old ones)
* 'pm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (76 commits)
PM / Hibernate: Implement compat_ioctl for /dev/snapshot
PM / Freezer: fix return value of freezable_schedule_timeout_killable()
PM / shmobile: Allow the A4R domain to be turned off at run time
PM / input / touchscreen: Make st1232 use device PM QoS constraints
PM / QoS: Introduce dev_pm_qos_add_ancestor_request()
PM / shmobile: Remove the stay_on flag from SH7372's PM domains
PM / shmobile: Don't include SH7372's INTCS in syscore suspend/resume
PM / shmobile: Add support for the sh7372 A4S power domain / sleep mode
PM: Drop generic_subsys_pm_ops
PM / Sleep: Remove forward-only callbacks from AMBA bus type
PM / Sleep: Remove forward-only callbacks from platform bus type
PM: Run the driver callback directly if the subsystem one is not there
PM / Sleep: Make pm_op() and pm_noirq_op() return callback pointers
PM/Devfreq: Add Exynos4-bus device DVFS driver for Exynos4210/4212/4412.
PM / Sleep: Merge internal functions in generic_ops.c
PM / Sleep: Simplify generic system suspend callbacks
PM / Hibernate: Remove deprecated hibernation snapshot ioctls
PM / Sleep: Fix freezer failures due to racy usermodehelper_is_disabled()
ARM: S3C64XX: Implement basic power domain support
PM / shmobile: Use common always on power domain governor
...
Fix up trivial conflict in fs/xfs/xfs_buf.c due to removal of unused
XBT_FORCE_SLEEP bit
This resolves the conflict in the arch/arm/mach-s3c64xx/s3c6400.c file,
and it fixes the build error in the arch/x86/kernel/microcode_core.c
file, that the merge did not catch.
The microcode_core.c patch was provided by Stephen Rothwell
<sfr@canb.auug.org.au> who was invaluable in the merge issues involved
with the large sysdev removal process in the driver-core tree.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The status/sense URB is allocated on per-command basis. A read/write
looks the following way on a stream-less connection:
- send cmd tag X, queue status
- receive status, oh it is a read for tag X. queue status & read
- receive read
- receive status, oh I'm done for tag X. Cool call complete and free
status urb.
This block repeats itself 1:1 for further commands and looks great so
far. Lets take a look now what happens if we do allow multiple commands:
- send cmd tag X, queue statusX (belongs to the command with the X tag)
- send cmd tag Y, queue statusY (belongs to the command with the Y tag)
- receive statusX, oh it is a read for tag X. queue statusX & a read
- receive read
- receive statusY, oh I'm done for tag X. Cool call complete and free statusY.
- receive statusX, oh it is a read for tag Y. queue statusY & before we
queue the read the the following message can be observed:
|sd 0:0:0:0: [sda] sense urb submission failure
followed by a second attempt with the same result.
In order to address this problem we will use only one status URB for
each scsi host in case we don't have stream support (as suggested by
Matthew). This URB is requeued until the device removed. Nothing changes
on stream based endpoints.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
In "usb/uas: use unique tags for all LUNs" we make sure to create unique
tags across all LUNs. This patch uses scsi_host_find_tag() to obtain the
correct command which is associated with the tag.
The following changes are required:
- don't use sdev->current_cmnd anymore
Since we can have devices which don't support command queueing we must
ensure that we can tell the two commands apart. Even if a device
supports comand queuing we send the INQUIRY command "untagged" for
LUN1 while we can send a tagged command to LUN0 at the same time.
devinfo->cmnd is used for stashing the one "untagged" command.
- tag number is altered. If stream support is used then the tag number
must match the stream number. Therefore we can't use tag 0 and must
start at tag 1.
In case we have untagged commands (at least the first command) we must
be able to distinguish between command tag 0 (which becomes 1) and
untagged command (which becomes curently also 1).
The following tag numbers are used:
0: never
1: for untagged commands (devinfo->cmnd)
2+: tagged commands.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
I observed that on a device with multiple LUNs UAS was re-using the same
tag number for requests which were issued at the same time to both LUNs.
This patch uses scsi_init_shared_tag_map() to use unique tags for all
LUNs. With this patch I haven't seen the same tag number during the init
sequence anymore. Tag 1 is used for devices which do not adverise
command queueing.
This patch initilizes the queue before adding the scsi host like the
other two user in tree.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
In the UAS status URB completion handler, we need to free the URB, no
matter what happens. Fix a bug where we would leak the URB (and its
buffer) if we couldn't find a SCSI command that is associated with this
status phase.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
UAS can work with either USB 3.0 devices that support bulk streams, or
USB 2.0 devices that do not support bulk streams. When we're working
with a non-streams device, we need to be able to uniquely identify a
SCSI command with a tag in the IU. Devices will barf and abort all
queued commands if they find a duplicate tag.
uas_queuecommand_lck() sets cmdinfo->stream to zero if the device
doesn't support streams, which is later passed into uas_alloc_cmd_urb()
as the variable stream. This means the UAS driver was setting the tag
in all commands to zero for non-stream devices. So the UAS driver won't
currently work with USB 2.0 devices.
Use the SCSI command tag instead of the stream ID for the command IU
tag. We have to add one to the SCSI command tag because SCSI tags are
zero-based, but stream IDs are one-based, and the command tag must match
the stream ID that we're queueing the data IUs for. Untagged SCSI
commands use stream ID 1.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
If the original submission (or allocation) of the URBs for a SCSI
command fails, the UAS driver sticks the command structure in a
workqueue and schedules uas_do_work() to run. That function removes the
entire queue before walking across it and attempting to resubmit.
Unfortunately, if the second submission fails, we will leak memory
(because an allocated URB was not submitted) and possibly leave the SCSI
command partially enqueued on some of the stream rings. Fix this by
checking whether the second submission failed and re-queueing the
command to the UAS workqueue and scheduling it.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
* master: (848 commits)
SELinux: Fix RCU deref check warning in sel_netport_insert()
binary_sysctl(): fix memory leak
mm/vmalloc.c: remove static declaration of va from __get_vm_area_node
ipmi_watchdog: restore settings when BMC reset
oom: fix integer overflow of points in oom_badness
memcg: keep root group unchanged if creation fails
nilfs2: potential integer overflow in nilfs_ioctl_clean_segments()
nilfs2: unbreak compat ioctl
cpusets: stall when updating mems_allowed for mempolicy or disjoint nodemask
evm: prevent racing during tfm allocation
evm: key must be set once during initialization
mmc: vub300: fix type of firmware_rom_wait_states module parameter
Revert "mmc: enable runtime PM by default"
mmc: sdhci: remove "state" argument from sdhci_suspend_host
x86, dumpstack: Fix code bytes breakage due to missing KERN_CONT
IB/qib: Correct sense on freectxts increment and decrement
RDMA/cma: Verify private data length
cgroups: fix a css_set not found bug in cgroup_attach_proc
oprofile: Fix uninitialized memory access when writing to writing to oprofilefs
Revert "xen/pv-on-hvm kexec: add xs_reset_watches to shutdown watches from old kernel"
...
Conflicts:
kernel/cgroup_freezer.c
Kingston DT 101 G2 replies a wrong tag while transporting, add an
unusal_devs entry to ignore the tag validation.
Signed-off-by: Qinglin Ye <yestyle@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This pulls in the latest USB bugfixes and helps a few of the drivers
merge nicer in the future due to changes in both branches.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'pm-freezer' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/misc: (24 commits)
freezer: fix wait_event_freezable/__thaw_task races
freezer: kill unused set_freezable_with_signal()
dmatest: don't use set_freezable_with_signal()
usb_storage: don't use set_freezable_with_signal()
freezer: remove unused @sig_only from freeze_task()
freezer: use lock_task_sighand() in fake_signal_wake_up()
freezer: restructure __refrigerator()
freezer: fix set_freezable[_with_signal]() race
freezer: remove should_send_signal() and update frozen()
freezer: remove now unused TIF_FREEZE
freezer: make freezing() test freeze conditions in effect instead of TIF_FREEZE
cgroup_freezer: prepare for removal of TIF_FREEZE
freezer: clean up freeze_processes() failure path
freezer: kill PF_FREEZING
freezer: test freezable conditions while holding freezer_lock
freezer: make freezing indicate freeze condition in effect
freezer: use dedicated lock instead of task_lock() + memory barrier
freezer: don't distinguish nosig tasks on thaw
freezer: remove racy clear_freeze_flag() and set PF_NOFREEZE on dead tasks
freezer: rename thaw_process() to __thaw_task() and simplify the implementation
...
The current implementation of set_freezable_with_signal() is buggy and
tricky to get right. usb-storage is the only user and its use can be
avoided trivially.
All usb-storage wants is to be able to sleep with timeout and get
woken up if freezing() becomes true. This can be trivially
implemented by doing interruptible wait w/ freezing() included in the
wait condition. There's no reason to use set_freezable_with_signal().
Perform interruptible wait on freezing() instead of using
set_freezable_with_signal(), which is scheduled for removal.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Seth Forshee <seth.forshee@canonical.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
This converts the drivers in drivers/usb/* to use the
module_usb_driver() macro which makes the code smaller and a bit
simpler.
Added bonus is that it removes some unneeded kernel log messages about
drivers loading and/or unloading.
Cc: Simon Arlott <cxacru@fire.lp0.eu>
Cc: Duncan Sands <duncan.sands@free.fr>
Cc: Matthieu CASTET <castet.matthieu@free.fr>
Cc: Stanislaw Gruszka <stf_xl@wp.pl>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: Oliver Neukum <oliver@neukum.name>
Cc: Juergen Stuber <starblue@users.sourceforge.net>
Cc: Cesar Miquel <miquel@df.uba.ar>
Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Cc: Matthew Wilcox <willy@linux.intel.com>
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Lucas De Marchi <lucas.demarchi@profusion.mobi>
Cc: Michael Hund <mhund@ld-didactic.de>
Cc: Zack Parsons <k3bacon@gmail.com>
Cc: Melchior FRANZ <mfranz@aon.at>
Cc: Tomoki Sekiyama <tomoki.sekiyama@gmail.com>
Cc: Dan Carpenter <error27@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use kmemdup rather than duplicating its implementation
The semantic patch that makes this change is available
in scripts/coccinelle/api/memdup.cocci.
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix the following sparse warning:
| drivers/usb/storage/shuttle_usbat.c:173:22: warning:
| symbol 'usbat_usb_ids' was not declared. Should
| it be static?
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix the following sparse warning:
| drivers/usb/storage/sddr55.c:51:22: warning: symbol
| 'sddr55_usb_ids' was not declared. Should it
| be static?
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix the following sparse warning:
| drivers/usb/storage/sddr09.c:74:22: warning: symbol
| 'sddr09_usb_ids' was not declared. Should it
| be static?
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix the following sparse warnings:
| drivers/usb/storage/realtek_cr.c:821:6: warning: symbol
| 'rts51x_invoke_transport' was not declared. Should
| it be static?
|
| drivers/usb/storage/realtek_cr.c:980:5: warning: symbol
| 'realtek_cr_suspend' was not declared. Should it
| be static?
|
| drivers/usb/storage/realtek_cr.c:518:23: warning: cast
| truncates bits from constant value (fe47 becomes 47)
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix the following sparse warning:
| drivers/usb/storage/onetouch.c:72:22: warning: symbol
| 'onetouch_usb_ids' was not declared. Should it
| be static?
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix the following sparse warning:
| drivers/usb/storage/karma.c:62:22: warning: symbol
| 'karma_usb_ids' was not declared. Should it
| be static?
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix the following sparse warning:
| drivers/usb/storage/jumpshot.c:74:22: warning: symbol
| 'jumpshot_usb_ids' was not declared. Should it
| be static?
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix the following sparse warning:
| drivers/usb/storage/freecom.c:122:22: warning: symbol
| 'freecom_usb_ids' was not declared. Should it
| be static?
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix the following sparse warning:
| drivers/usb/storage/freecom.c:122:22: warning: symbol
| 'freecom_usb_ids' was not declared. Should it
| be static?
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix the following sparse warnings:
| drivers/usb/storage/ene_ub6250.c:45:22: warning: symbol
| 'ene_ub6250_usb_ids' was not declared. Should it
| be static?
|
| drivers/usb/storage/ene_ub6250.c:780:5: warning: symbol
| 'ms_lib_alloc_logicalmap' was not declared. Should it
| be static?
|
| drivers/usb/storage/ene_ub6250.c:2251:5: warning: symbol
| 'ms_scsi_irp' was not declared. Should it be static?
|
| drivers/usb/storage/ene_ub6250.c:638:29: warning: right shift by bigger
| than source value
|
| drivers/usb/storage/ene_ub6250.c:639:29: warning: right shift by bigger
| than source value
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix the following sparse warning:
| drivers/usb/storage/datafab.c:91:22: warning: symbol
| 'datafab_usb_ids' was not declared. Should it
| be static?
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix the following sparse warning:
| drivers/usb/storage/cypress_atacb.c:46:22: warning:
| symbol 'cypress_usb_ids' was not declared. Should
| it be static?
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix the following warning:
| drivers/usb/storage/alauda.c:142:22: warning: symbol
| 'alauda_usb_ids' was not declared. Should it
| be static?
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix the following compile warning:
| drivers/usb/storage/ene_ub6250.c: In function ‘ms_scsi_write’:
| drivers/usb/storage/ene_ub6250.c:1728:6: warning: ‘result’ may \
| be used uninitialized in this function [-Wuninitialized]
| drivers/usb/storage/ene_ub6250.c:1795:77: warning: ‘offset’ may \
| be used uninitialized in this function [-Wuninitialized]
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The 8020i protocol (also 8070i and QIC-157) uses 12-byte commands;
shorter commands must be padded. Simon Detheridge reports that his
3-TB USB disk drive claims to use the 8020i protocol (which is
normally meant for ATAPI devices like CD drives), and because of its
large size, the disk drive requires the use of 16-byte commands.
However the usb_stor_pad12_command() routine in usb-storage always
sets the command length to 12, making the drive impossible to use.
Since the SFF-8020i specification allows for 16-byte commands in
future extensions, we may as well accept them. This patch (as1490)
changes usb_stor_pad12_command() to leave commands larger than 12
bytes alone rather than truncating them.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Simon Detheridge <simon@widgit.com>
CC: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
With module.h being implicitly everywhere via device.h, the absence
of explicitly including something for EXPORT_SYMBOL went unnoticed.
Since we are heading to fix things up and clean module.h from the
device.h file, we need to explicitly include these files now.
Use the lightweight version of the header that has just THIS_MODULE
and EXPORT_SYMBOL variants.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The situation up to this point meant that module.h was pretty
much everywhere, regardless of whether you asked for it or not.
We are fixing that, so give the USB folks who want it an actual
include of it.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
* 'usb-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (260 commits)
usb: renesas_usbhs: fixup inconsistent return from usbhs_pkt_push()
usb/isp1760: Allow to optionally trigger low-level chip reset via GPIOLIB.
USB: gadget: midi: memory leak in f_midi_bind_config()
USB: gadget: midi: fix range check in f_midi_out_open()
QE/FHCI: fixed the CONTROL bug
usb: renesas_usbhs: tidyup for smatch warnings
USB: Fix USB Kconfig dependency problem on 85xx/QoirQ platforms
EHCI: workaround for MosChip controller bug
usb: gadget: file_storage: fix race on unloading
USB: ftdi_sio.c: Use ftdi async_icount structure for TIOCMIWAIT, as in other drivers
USB: ftdi_sio.c:Fill MSR fields of the ftdi async_icount structure
USB: ftdi_sio.c: Fill LSR fields of the ftdi async_icount structure
USB: ftdi_sio.c:Fill TX field of the ftdi async_icount structure
USB: ftdi_sio.c: Fill the RX field of the ftdi async_icount structure
USB: ftdi_sio.c: Basic icount infrastructure for ftdi_sio
usb/isp1760: Let OF bindings depend on general CONFIG_OF instead of PPC_OF .
USB: ftdi_sio: Support TI/Luminary Micro Stellaris BD-ICDI Board
USB: Fix runtime wakeup on OHCI
xHCI/USB: Make xHCI driver have a BOS descriptor.
usb: gadget: add new usb gadget for ACM and mass storage
...
After auto-delink command is triggered, the CSW won't be sent back
to host side, in which scenario, the USB Mass Storage driver will
wait for the completion of the URB for MAX_SCHEDULE_TIMEOUT.
Signed-off-by: edwin_rong <edwin_rong@realsil.com.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A typo in the configuration variable name prevents from activating the
USB autosuspend on the device.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It was pointed out by 'make versioncheck' that linux/version.h was not
always being included where needed and sometimes included needlessly
in drivers/usb/.
This patch fixes up the includes.
For the UVC gadget driver bits, this was ACK'ed by Laurent Pinchart.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
