When starting aggregation, the code checks the status of the queue
allocated to the aggregation tid, which might not yet be allocated
and thus the queue index may be invalid.
Fix this by reserving a new queue in case the queue id is invalid.
While at it, clean up some unreachable code (a condition that is
already handled earlier) and remove all the non-DQA comments since
non-DQA mode is no longer supported.
Fixes: cf961e1662 ("iwlwifi: mvm: support dqa-mode agg on non-shared queue")
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If the driver failed to resume from D3, it is possible that it has
no valid aux station. In such case, fw restart will end up in sending
station related commands with an invalid station id, which will
result in an assert.
Fix this by allocating a new station id for the aux station if it
does not have a valid id even in the case of fw restart.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When a queue is reserved for aggregation, the queue id is assigned
to the tid_data. This is fine since iwl_mvm_sta_tx_agg_oper()
takes care of allocating the queue before actual tx starts.
When the reservation is cancelled (e.g. when the AP declined the
aggregation request) the tid_data is not cleared. As a result,
following tx for this tid was trying to use an unallocated queue.
Fix this by setting the txq_id for the tid to invalid when unreserving
the queue.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
After switching to a new channel, driver schedules session protection
time event in order to hear the beacon on the new channel.
The duration of the protection is two beacon intervals.
However, since we start to switch slightly before beacon with count 1, in
case we don't hear (or AP doesn't transmit) the very first beacon on the
new channel the protection ends without hearing any beacon at all.
At this stage the switch is not complete, the queues are closed and the
interface doesn't have quota yet or TBTT events. As the result, we are
stuck forever waiting for iwl_mvm_post_channel_switch() to be called.
Fix this by increasing the protection time to be 3 beacon intervals and
in addition drop the connection if the time event ends before we got any
beacon.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We shouldn't allow a tunnel to have IP_MAX_MTU as MTU, because
another IPv6 header is going on top of our packets. Without this
patch, we might end up building packets bigger than IP_MAX_MTU.
Fixes: b96f9afee4 ("ipv4/6: use core net MTU range checking")
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Acked-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
In vti6_link_config(), if MTU is already given on link creation
or change, validate and use it instead of recomputing it. To do
that, we need to propagate the knowledge that MTU was set by
userspace all the way down to vti6_link_config().
To keep this simple, vti6_dev_init() sets the new 'keep_mtu'
argument of vti6_link_config() to true: on initialization, we
don't have convenient access to netlink attributes there, but we
will anyway check whether dev->mtu is set in vti6_link_config().
If it's non-zero, it was set to the value of the IFLA_MTU
attribute during creation. Otherwise, determine a reasonable
value.
Fixes: ed1efb2aef ("ipv6: Add support for IPsec virtual tunnel interfaces")
Fixes: 53c81e95df ("ip6_vti: adjust vti mtu according to mtu of lower device")
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Acked-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
If a lower device is found, we don't need to subtract
LL_MAX_HEADER to calculate our MTU: just use its MTU, the link
layer headers are already taken into account by it.
If the lower device is not found, start from ETH_DATA_LEN
instead, and only in this case subtract a worst-case
LL_MAX_HEADER.
We then need to subtract our additional IPv6 header from the
calculation.
While at it, note that vti6 doesn't have a hardware header, so
it doesn't need to set dev->hard_header_len. And as
vti6_link_config() now always sets the MTU, there's no need to
set a default value in vti6_dev_setup().
This makes the behaviour consistent with IPv4 vti, after
commit a32452366b ("vti4: Don't count header length twice."),
which was accidentally reverted by merge commit f895f0cfbb
("Merge branch 'master' of
git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec").
While commit 53c81e95df ("ip6_vti: adjust vti mtu according to
mtu of lower device") improved on the original situation, this
was still not ideal. As reported in that commit message itself,
if we start from an underlying veth MTU of 9000, we end up with
an MTU of 8832, that is, 9000 - LL_MAX_HEADER - sizeof(ipv6hdr).
This should simply be 8880, or 9000 - sizeof(ipv6hdr) instead:
we found the lower device (veth) and we know we don't have any
additional link layer header, so there's no need to subtract an
hypothetical worst-case number.
Fixes: 53c81e95df ("ip6_vti: adjust vti mtu according to mtu of lower device")
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Acked-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Don't hardcode a MTU value on vti tunnel initialization,
ip_tunnel_newlink() is able to deal with this already. See also
commit ffc2b6ee41 ("ip_gre: fix IFLA_MTU ignored on NEWLINK").
Fixes: 1181412c1a ("net/ipv4: VTI support new module for ip_vti.")
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Acked-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Otherwise, it's possible to specify invalid MTU values directly
on creation of a link (via 'ip link add'). This is already
prevented on subsequent MTU changes by commit b96f9afee4
("ipv4/6: use core net MTU range checking").
Fixes: c544193214 ("GRE: Refactor GRE tunneling code.")
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Acked-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
This re-introduces the effect of commit a32452366b ("vti4:
Don't count header length twice.") which was accidentally
reverted by merge commit f895f0cfbb ("Merge branch 'master' of
git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec").
The commit message from Steffen Klassert said:
We currently count the size of LL_MAX_HEADER and struct iphdr
twice for vti4 devices, this leads to a wrong device mtu.
The size of LL_MAX_HEADER and struct iphdr is already counted in
ip_tunnel_bind_dev(), so don't do it again in vti_tunnel_init().
And this is still the case now: ip_tunnel_bind_dev() already
accounts for the header length of the link layer (not
necessarily LL_MAX_HEADER, if the output device is found), plus
one IP header.
For example, with a vti device on top of veth, with MTU of 1500,
the existing implementation would set the initial vti MTU to
1332, accounting once for LL_MAX_HEADER (128, included in
hard_header_len by vti) and twice for the same IP header (once
from hard_header_len, once from ip_tunnel_bind_dev()).
It should instead be 1480, because ip_tunnel_bind_dev() is able
to figure out that the output device is veth, so no additional
link layer header is attached, and will properly count one
single IP header.
The existing issue had the side effect of avoiding PMTUD for
most xfrm policies, by arbitrarily lowering the initial MTU.
However, the only way to get a consistent PMTU value is to let
the xfrm PMTU discovery do its course, and commit d6af1a31cc
("vti: Add pmtu handling to vti_xmit.") now takes care of local
delivery cases where the application ignores local socket
notifications.
Fixes: b9959fd3b0 ("vti: switch to new ip tunnel code")
Fixes: f895f0cfbb ("Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec")
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Acked-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
The #sound-dai-cells DT property is required to describe link between
the HDMI IP block and the SoC's audio subsystem.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
When unbinding/removing the driver, we will run into the following warnings:
[ 259.655198] fec 400d1000.ethernet: 400d1000.ethernet supply phy not found, using dummy regulator
[ 259.665065] fec 400d1000.ethernet: Unbalanced pm_runtime_enable!
[ 259.672770] fec 400d1000.ethernet (unnamed net_device) (uninitialized): Invalid MAC address: 00:00:00:00:00:00
[ 259.683062] fec 400d1000.ethernet (unnamed net_device) (uninitialized): Using random MAC address: f2:3e:93:b7:29:c1
[ 259.696239] libphy: fec_enet_mii_bus: probed
Avoid these warnings by balancing the runtime PM calls during fec_drv_remove().
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull x86/pti updates from Thomas Gleixner:
"Another set of melted spectrum updates:
- Iron out the last late microcode loading issues by actually
checking whether new microcode is present and preventing the CPU
synchronization to run into a timeout induced hang.
- Remove Skylake C2 from the microcode blacklist according to the
latest Intel documentation
- Fix the VM86 POPF emulation which traps if VIP is set, but VIF is
not. Enhance the selftests to catch that kind of issue
- Annotate indirect calls/jumps for objtool on 32bit. This is not a
functional issue, but for consistency sake its the right thing to
do.
- Fix a jump label build warning observed on SPARC64 which uses 32bit
storage for the code location which is casted to 64 bit pointer w/o
extending it to 64bit first.
- Add two new cpufeature bits. Not really an urgent issue, but
provides them for both x86 and x86/kvm work. No impact on the
current kernel"
* 'x86-pti-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/microcode: Fix CPU synchronization routine
x86/microcode: Attempt late loading only when new microcode is present
x86/speculation: Remove Skylake C2 from Speculation Control microcode blacklist
jump_label: Fix sparc64 warning
x86/speculation, objtool: Annotate indirect calls/jumps for objtool on 32-bit kernels
x86/vm86/32: Fix POPF emulation
selftests/x86/entry_from_vm86: Add test cases for POPF
selftests/x86/entry_from_vm86: Exit with 1 if we fail
x86/cpufeatures: Add Intel PCONFIG cpufeature
x86/cpufeatures: Add Intel Total Memory Encryption cpufeature
Pull x86 fix from Thomas Gleixner:
"A single fix for vmalloc_fault() which uses p*d_huge() unconditionally
whether CONFIG_HUGETLBFS is set or not. In case of CONFIG_HUGETLBFS=n
this results in a crash as p*d_huge() returns 0 in that case"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mm: Fix vmalloc_fault to use pXd_large
Pull irq fixes from Thomas Gleixner:
"Three fixes for irq chip drivers:
- Make sure the allocations in the GIC-V3 ITS driver are large enough
to accomodate the interrupt space
- Fix a misplaced __iomem annotation which causes a splat of 26
sparse warnings
- Remove an unused function in the IMX GPCV2 driver which causes
build warnings"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/irq-imx-gpcv2: Remove unused function
irqchip/gic-v3-its: Ensure nr_ites >= nr_lpis
irqchip/gic-v3-its: Fix misplaced __iomem annotations
Pull EFI fix from Thomas Gleixner:
"A single fix to prevent partially initialized pointers in mixed mode
(64bit kernel on 32bit UEFI)"
* 'efi-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi/libstub/tpm: Initialize pointer variables to zero for mixed mode
lockups on POWER9.
* ARM: locking fix, reset fix, GICv2 multi-source SGI injection fix,
GICv2-on-v3 MMIO synchronization fix, make the console less verbose.
* x86: fix device passthrough on AMD SME.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJariCQAAoJEL/70l94x66D6j4H/iS51f1EFRjTXbM+/D0BxpOD
hTz3tiV4JNezwXkxm9FMr7e5sfONTsqZodzCeXbz9XRmb6lwkEIbaPC4G2ALJeBH
V1Gpy2NsoBNCaU6Ci7SGqs1PG7wmG1tGMkzgkUoi2mwJRbA7UfnPmL1bTRESc4/w
oYN5xPj1/bLYWnok2cEJevND2VUTy+/dazpm+9gZzHqeoBnRRhhNluLW11A7yi2U
mSxAZrCH8X9EejIEhU8jAah4PYZ9tP8TmvUcnAPYpNgDh2JH6tlkGAYSbpadiCvf
FJNhtev67uDL1jPzqQJLNo5Z04cg06M+9cYqrLD1q287LXsKs+LHXJY/AI56oIM=
=YHkv
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
"PPC:
- fix bug leading to lost IPIs and smp_call_function_many() lockups
on POWER9
ARM:
- locking fix
- reset fix
- GICv2 multi-source SGI injection fix
- GICv2-on-v3 MMIO synchronization fix
- make the console less verbose.
x86:
- fix device passthrough on AMD SME"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86: Fix device passthrough when SME is active
kvm: arm/arm64: vgic-v3: Tighten synchronization for guests using v2 on v3
KVM: arm/arm64: vgic: Don't populate multiple LRs with the same vintid
KVM: arm/arm64: Reduce verbosity of KVM init log
KVM: arm/arm64: Reset mapped IRQs on VM reset
KVM: arm/arm64: Avoid vcpu_load for other vcpu ioctls than KVM_RUN
KVM: arm/arm64: vgic: Add missing irq_lock to vgic_mmio_read_pending
KVM: PPC: Book3S HV: Fix trap number return from __kvmppc_vcore_entry
batadv_check_unicast_ttvn may redirect a packet to itself or another
originator. This involves rewriting the ttvn and the destination address in
the batadv unicast header. These field were not yet pulled (with skb rcsum
update) and thus any change to them also requires a change in the receive
checksum.
Reported-by: Matthias Schiffer <mschiffer@universe-factory.net>
Fixes: a73105b8d4 ("batman-adv: improved client announcement mechanism")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
'Commit 45dac1d6ea ("vmxnet3: Changes for vmxnet3 adapter version 2
(fwd)")' introduced a flag "lro" in structure vmxnet3_adapter which is
used to indicate whether LRO is enabled or not. However, the patch
did not set the flag and hence it was never exercised.
So, when LRO is enabled, it resulted in poor TCP performance due to
delayed acks. This issue is seen with packets which are larger than
the mss getting a delayed ack rather than an immediate ack, thus
resulting in high latency.
This patch removes the lro flag and directly uses device features
against NETIF_F_LRO to check if lro is enabled.
Fixes: 45dac1d6ea ("vmxnet3: Changes for vmxnet3 adapter version 2 (fwd)")
Reported-by: Rachel Lunnon <rachel_lunnon@stormagic.com>
Signed-off-by: Ronak Doshi <doshir@vmware.com>
Acked-by: Shrikrishna Khare <skhare@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The field txNumDeferred is used by the driver to keep track of the number
of packets it has pushed to the emulation. The driver increments it on
pushing the packet to the emulation and the emulation resets it to 0 at
the end of the transmit.
There is a possibility of a race either when (a) ESX is under heavy load or
(b) workload inside VM is of low packet rate.
This race results in xmit hangs when network coalescing is disabled. This
change creates a local copy of txNumDeferred and uses it to perform ring
arithmetic.
Reported-by: Noriho Tanaka <ntanaka@vmware.com>
Signed-off-by: Ronak Doshi <doshir@vmware.com>
Acked-by: Shrikrishna Khare <skhare@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Davide Caratti says:
====================
net/sched: fix NULL dereference in the error path of .init()
with several TC actions it's possible to see NULL pointer dereference,
when the .init() function calls tcf_idr_alloc(), fails at some point and
then calls tcf_idr_release(): this series fixes all them introducing
non-NULL tests in the .cleanup() function.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
According to AM335x TRM[1] 14.3.6.2, AM437x TRM[2] 15.3.6.2 and
DRA7 TRM[3] 24.11.4.8.7.3.3, in-band mode in EXT_EN(bit18) register is only
available when PHY is configured in RGMII mode with 10Mbps speed. It will
cause some networking issues without RGMII mode, such as carrier sense
errors and low throughput. TI also mentioned this issue in their forum[4].
This patch adds the check mechanism for PHY interface with RGMII interface
type, the in-band mode can only be set in RGMII mode with 10Mbps speed.
References:
[1]: https://www.ti.com/lit/ug/spruh73p/spruh73p.pdf
[2]: http://www.ti.com/lit/ug/spruhl7h/spruhl7h.pdf
[3]: http://www.ti.com/lit/ug/spruic2b/spruic2b.pdf
[4]: https://e2e.ti.com/support/arm/sitara_arm/f/791/p/640765/2392155
Suggested-by: Holsety Chen (陳憲輝) <Holsety.Chen@moxa.com>
Signed-off-by: SZ Lin (林上智) <sz.lin@moxa.com>
Signed-off-by: Schuyler Patton <spatton@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver implementation returns support for private flags, while
no private flags are present. When asked for the number of private
flags it returns the number of statistic flag names.
Fix this by returning EOPNOTSUPP for not implemented ethtool flags.
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 9ffcc3725f ("mlxsw: spectrum: Allow packets to be trapped
from any PG") I fixed a problem where packets could not be trapped to
the CPU due to exceeded shared buffer quotas. The mentioned commit
explains the problem in detail.
The problem was fixed by assigning a minimum quota for the CPU port and
the traffic class used for scheduling traffic to the CPU.
However, commit 117b0dad2d ("mlxsw: Create a different trap group list
for each device") assigned different traffic classes to different
packet types and rendered the fix useless.
Fix the problem by assigning a minimum quota for the CPU port and all
the traffic classes that are currently in use.
Fixes: 117b0dad2d ("mlxsw: Create a different trap group list for each device")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Eddie Shklaer <eddies@mellanox.com>
Tested-by: Eddie Shklaer <eddies@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
syzbot reported one use-after-free in pfifo_fast_enqueue() [1]
Issue here is that we can not reuse skb after a successful skb_array_produce()
since another cpu might have consumed it already.
I believe a similar problem exists in try_bulk_dequeue_skb_slow()
in case we put an skb into qdisc_enqueue_skb_bad_txq() for lockless qdisc.
[1]
BUG: KASAN: use-after-free in qdisc_pkt_len include/net/sch_generic.h:610 [inline]
BUG: KASAN: use-after-free in qdisc_qstats_cpu_backlog_inc include/net/sch_generic.h:712 [inline]
BUG: KASAN: use-after-free in pfifo_fast_enqueue+0x4bc/0x5e0 net/sched/sch_generic.c:639
Read of size 4 at addr ffff8801cede37e8 by task syzkaller717588/5543
CPU: 1 PID: 5543 Comm: syzkaller717588 Not tainted 4.16.0-rc4+ #265
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:17 [inline]
dump_stack+0x194/0x24d lib/dump_stack.c:53
print_address_description+0x73/0x250 mm/kasan/report.c:256
kasan_report_error mm/kasan/report.c:354 [inline]
kasan_report+0x23c/0x360 mm/kasan/report.c:412
__asan_report_load4_noabort+0x14/0x20 mm/kasan/report.c:432
qdisc_pkt_len include/net/sch_generic.h:610 [inline]
qdisc_qstats_cpu_backlog_inc include/net/sch_generic.h:712 [inline]
pfifo_fast_enqueue+0x4bc/0x5e0 net/sched/sch_generic.c:639
__dev_xmit_skb net/core/dev.c:3216 [inline]
Fixes: c5ad119fb6 ("net: sched: pfifo_fast use skb_array")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot+ed43b6903ab968b16f54@syzkaller.appspotmail.com
Cc: John Fastabend <john.fastabend@gmail.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Just when I had decided that flush_cache_range() was always called with
a valid context, Helge reported two cases where the
"BUG_ON(!vma->vm_mm->context);" was hit on the phantom buildd:
kernel BUG at /mnt/sdb6/linux/linux-4.15.4/arch/parisc/kernel/cache.c:587!
CPU: 1 PID: 3254 Comm: kworker/1:2 Tainted: G D 4.15.0-1-parisc64-smp #1 Debian 4.15.4-1+b1
Workqueue: events free_ioctx
IAOQ[0]: flush_cache_range+0x164/0x168
IAOQ[1]: flush_cache_page+0x0/0x1c8
RP(r2): unmap_page_range+0xae8/0xb88
Backtrace:
[<00000000404a6980>] unmap_page_range+0xae8/0xb88
[<00000000404a6ae0>] unmap_single_vma+0xc0/0x188
[<00000000404a6cdc>] zap_page_range_single+0x134/0x1f8
[<00000000404a702c>] unmap_mapping_range+0x1cc/0x208
[<0000000040461518>] truncate_pagecache+0x98/0x108
[<0000000040461624>] truncate_setsize+0x9c/0xb8
[<00000000405d7f30>] put_aio_ring_file+0x80/0x100
[<00000000405d803c>] aio_free_ring+0x8c/0x290
[<00000000405d82c0>] free_ioctx+0x80/0x180
[<0000000040284e6c>] process_one_work+0x21c/0x668
[<00000000402854c4>] worker_thread+0x20c/0x778
[<0000000040291d44>] kthread+0x2d4/0x2e0
[<0000000040204020>] end_fault_vector+0x20/0xc0
This indicates that we need to handle the no context case in
flush_cache_range() as we do in flush_cache_mm().
In thinking about this, I realized that we don't need to flush the TLB
when there is no context. So, I added context checks to the large flush
cases in flush_cache_mm() and flush_cache_range(). The large flush case
occurs frequently in flush_cache_mm() and the change should improve fork
performance.
The v2 version of this change removes the BUG_ON from flush_cache_page()
by skipping the TLB flush when there is no context. I also added code
to flush the TLB in flush_cache_mm() and flush_cache_range() when we
have a context that's not current. Now all three routines handle TLB
flushes in a similar manner.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Cc: stable@vger.kernel.org # 4.9+
Signed-off-by: Helge Deller <deller@gmx.de>
-----BEGIN PGP SIGNATURE-----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=bXFe
-----END PGP SIGNATURE-----
Merge tag 'for-4.16-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
"There's an important revert in this pull request that needs to go to
stable as it causes a corruption on big endian machines.
The other fix is for FIEMAP incorrectly reporting shared extents
before a sync and one fix for a crash in raid56.
So far we got only one report about the BE corruption, the stable
kernels were out for like a week, so hopefully the scope of the damage
is low"
* tag 'for-4.16-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
Revert "btrfs: use proper endianness accessors for super_copy"
btrfs: add missing initialization in btrfs_check_shared
btrfs: Fix NULL pointer exception in find_bio_stripe
Emanuel reported an issue with a hang during microcode update because my
dumb idea to use one atomic synchronization variable for both rendezvous
- before and after update - was simply bollocks:
microcode: microcode_reload_late: late_cpus: 4
microcode: __reload_late: cpu 2 entered
microcode: __reload_late: cpu 1 entered
microcode: __reload_late: cpu 3 entered
microcode: __reload_late: cpu 0 entered
microcode: __reload_late: cpu 1 left
microcode: Timeout while waiting for CPUs rendezvous, remaining: 1
CPU1 above would finish, leave and the others will still spin waiting for
it to join.
So do two synchronization atomics instead, which makes the code a lot more
straightforward.
Also, since the update is serialized and it also takes quite some time per
microcode engine, increase the exit timeout by the number of CPUs on the
system.
That's ok because the moment all CPUs are done, that timeout will be cut
short.
Furthermore, panic when some of the CPUs timeout when returning from a
microcode update: we can't allow a system with not all cores updated.
Also, as an optimization, do not do the exit sync if microcode wasn't
updated.
Reported-by: Emanuel Czirai <xftroxgpx@protonmail.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Emanuel Czirai <xftroxgpx@protonmail.com>
Tested-by: Ashok Raj <ashok.raj@intel.com>
Tested-by: Tom Lendacky <thomas.lendacky@amd.com>
Link: https://lkml.kernel.org/r/20180314183615.17629-2-bp@alien8.de
Return UCODE_NEW from the scanning functions to denote that new microcode
was found and only then attempt the expensive synchronization dance.
Reported-by: Emanuel Czirai <xftroxgpx@protonmail.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Emanuel Czirai <xftroxgpx@protonmail.com>
Tested-by: Ashok Raj <ashok.raj@intel.com>
Tested-by: Tom Lendacky <thomas.lendacky@amd.com>
Link: https://lkml.kernel.org/r/20180314183615.17629-1-bp@alien8.de
-----BEGIN PGP SIGNATURE-----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=lSpS
-----END PGP SIGNATURE-----
Merge tag 'drm-fixes-for-v4.16-rc6' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"i915, amd and nouveau fixes.
i915:
- backlight fix for some panels
- pm fix
- fencing fix
- some GVT fixes
amdgpu:
- backlight fix across suspend/resume
- object destruction ordering issue fix
- displayport fix
nouveau:
- two backlight fixes
- fix for some lockups
Pretty quiet week, seems like everyone was fixing backlights"
* tag 'drm-fixes-for-v4.16-rc6' of git://people.freedesktop.org/~airlied/linux:
drm/nouveau/bl: fix backlight regression
drm/nouveau/bl: Fix oops on driver unbind
drm/nouveau/mmu: ALIGN_DOWN correct variable
drm/i915/gvt: fix user copy warning by whitelist workload rb_tail field
drm/i915/gvt: Correct the privilege shadow batch buffer address
drm/amdgpu/dce: Don't turn off DP sink when disconnected
drm/amdgpu: save/restore backlight level in legacy dce code
drm/radeon: fix prime teardown order
drm/amdgpu: fix prime teardown order
drm/i915: Kick the rps worker when changing the boost frequency
drm/i915: Only prune fences after wait-for-all
drm/i915: Enable VBT based BL control for DP
drm/i915/gvt: keep oa config in shadow ctx
drm/i915/gvt: Add runtime_pm_get/put into gvt_switch_mmio
Checking for 0 is insufficient: when an SKB without a batadv header, but
with a VLAN header is received, hdr_size will be 4, making the following
code interpret the Ethernet header as a batadv header.
Fixes: be1db4f661 ("batman-adv: make the Distributed ARP Table vlan aware")
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
batadv_check_unicast_ttvn() calls skb_cow(), so pointers into the SKB data
must be (re)set after calling it. The ethhdr variable is dropped
altogether.
Fixes: 7cdcf6dddc ("batman-adv: add UNICAST_4ADDR packet type")
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The MDIO busses are switch properties and so should be inside the
switch node. Fix the examples in the binding document.
Reported-by: 尤晓杰 <yxj790222@163.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Fixes: a3c53be55c ("net: dsa: mv88e6xxx: Support multiple MDIO busses")
Signed-off-by: David S. Miller <davem@davemloft.net>
When errors are enqueued to the error queue via sock_queue_err_skb()
function, it is possible that the waiting application is not notified.
Calling 'sk->sk_data_ready()' would not notify applications that
selected only POLLERR events in poll() (for example).
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reported-by: Randy E. Witt <randy.e.witt@intel.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
nlmsg_multicast() consumes always the skb, thus the original skb must be
freed only when this function is called with a clone.
Fixes: cb9f7a9a5c ("netlink: ensure to loop over all netns in genlmsg_multicast_allns()")
Reported-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Link updates were not reported to qedr correctly.
Leading to cases where a link could be down, but qedr
would see it as up.
In addition, once qede was loaded, link state would be up,
regardless of the actual link state.
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Kalderon says:
====================
qed: iWARP related fixes
This series contains two fixes related to iWARP flow.
====================
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
FW workaround. The iWARP LL2 connection did not expect TCP packets
to arrive on it's connection. The fix drops any non-tcp packets
Fixes b5c29ca ("qed: iWARP CM - setup a ll2 connection for handling
SYN packets")
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a corner case in the MPA unalign flow where a FPDU header is
split over two tcp segments. The length of the first fragment in this
case was not initialized properly and should be '1'
Fixes: c7d1d839 ("qed: Add support for MPA header being split over two tcp packets")
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Free memory by calling put_device(), if afiucv_iucv_init is not
successful.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need for complex checking between the last consumed index
and current consumed index, a simple subtraction will do.
This also eliminates the possibility of a permanent transmit queue stall
under the following conditions:
- one CPU bursts ring->size worth of traffic (up to 256 buffers), to the
point where we run out of free descriptors, so we stop the transmit
queue at the end of bcm_sysport_xmit()
- because of our locking, we have the transmit process disable
interrupts which means we can be blocking the TX reclamation process
- when TX reclamation finally runs, we will be computing the difference
between ring->c_index (last consumed index by SW) and what the HW
reports through its register
- this register is masked with (ring->size - 1) = 0xff, which will lead
to stripping the upper bits of the index (register is 16-bits wide)
- we will be computing last_tx_cn as 0, which means there is no work to
be done, and we never wake-up the transmit queue, leaving it
permanently disabled
A practical example is e.g: ring->c_index aka last_c_index = 12, we
pushed 256 entries, HW consumer index = 268, we mask it with 0xff = 12,
so last_tx_cn == 0, nothing happens.
Fixes: 80105befdb ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Need to lock lower socket in order to provide mutual exclusion
with kcm_unattach.
v2: Add Reported-by for syzbot
Fixes: ab7ac4eb98 ("kcm: Kernel Connection Multiplexor module")
Reported-by: syzbot+ea75c0ffcd353d32515f064aaebefc5279e6161e@syzkaller.appspotmail.com
Signed-off-by: Tom Herbert <tom@quantonium.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
