The FWNMI code uses a global buffer without any locks to read the RTAS error
information. If two CPUs take a machine check at once then we will corrupt
this buffer.
Since most FWNMI rtas messages are not of the extended type, we can create a
64bit percpu buffer and use it where possible. If we do receive an extended
RTAS log then we fall back to the old behaviour of using the global buffer.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Rework pseries machine check handler:
- If MSR_RI isn't set, we cannot recover even if the machine check was fully
recovered
- Rename nonfatal to recovered
- Handle RTAS_DISP_LIMITED_RECOVERY
- Use BUS_MCEERR_AR instead of BUS_ADRERR
- Don't check all the RTAS error log fields when receiving a synchronous
machine check. Recent versions of the pseries firmware do not fill them
in during a machine check and instead send a follow up error log with
the detailed information. If we see a synchronous machine check, and we
came from userspace then kill the task.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If a machine check comes from userspace we send a SIGBUS to the task and
fail to printk anything.
If we are taking machine checks due to bad hardware we want to know about
it right away. Furthermore if we don't complain loudly then it will look
a lot like a bug in the userspace application, potentially causing a lot
of confusion.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We are calling debugger_fault_handler twice in machine_check_exception.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Newer versions of the System p firwmare send a partial RTAS error log in the
machine check handler with a more detailed response appearing sometime later
via check event.
This means at machine check time we do not have enough information to
ascertain exactly what went on. Furthermore, I have found the RTAS error
logs in the machine check handler contain no useful information, so halting on
them makes little sense. If we want to halt it would make more sense to do
it following the error log received sometime later via check event.
In light of this, never halt the error log in the pseries machine
check handler.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We should never force MSR_RI on. If we take a machine check with MSR_RI off
then we have no chance of recovering safely.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We were printing 64 bits of DSISR in show_regs even though it is 32 bit.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We should disable ftrace during kexec, some of the tracers are very invasive
and we do not want them going off while doing the low level work of swapping
one kernel out for another. This mirrors what we do on x86.
Even though we cannot return from a kexec on powerpc (since we do not implement
CONFIG_KEXEC_JUMP), add the restore code in case we do one day.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Use the crash handler hooks to run the SPU stop code, just like we do for
ehea and cell RAS code.
While I'm here I noticed "CPUSs reliabally"
so fix the spelling MISTAKESs reliabally.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We check for a valid handler before calling ppc_md.machine_kexec_prepare
so we can just remove these empty handlers.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
There's no need to initialise ppc_md.machine_kexec and
ppc_md.machine_kexec_prepare to the default handlers.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
No one uses ppc_md.machine_crash_shutdown, so remove it.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
No one uses ppc_md.machine_kexec, so remove it.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
No one uses ppc_md.machine_kexec_cleanup, so remove it.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Move all the kexec handlers together.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
With cmwq, there's no reason to use a separate workqueue in
cpufreq_spudemand. Use system_wq instead. The work items are already
sync canceled on stop, so it's already guaranteed that no work is
running when spu_gov_exit() is entered.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: Dave Jones <davej@redhat.com>
Cc: cpufreq@vger.kernel.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Simplify read file operation for /proc/powerpc/rtas/* interface
by using simple_read_from_buffer.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Simplify several write fileoperations for spufs by using
simple_write_to_buffer().
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
32-bit variant of the previous patch for 64-bit:
<<
When an interrupt occurs in userspace, we can call trace_hardirqs_on/off()
With one level stack. But if we have irqsoff tracing enabled,
it checks both CALLER_ADDR0 and CALLER_ADDR1. The second call
goes two stack frames up. If this is from user space, then there may
not exist a second stack....
>>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When an interrupt occurs in userspace, we can call trace_hardirqs_on/off()
With one level stack. But if we have irqsoff tracing enabled,
it checks both CALLER_ADDR0 and CALLER_ADDR1. The second call
goes two stack frames up. If this is from user space, then there may
not exist a second stack.
Add a second stack when calling trace_hardirqs_on/off() otherwise
the following oops might occur:
Oops: Kernel access of bad area, sig: 11 [#1]
PREEMPT SMP NR_CPUS=2 PA Semi PWRficient
last sysfs file: /sys/block/sda/size
Modules linked in: ohci_hcd ehci_hcd usbcore
NIP: c0000000000e1c00 LR: c0000000000034d4 CTR: 000000011012c440
REGS: c00000003e2f3af0 TRAP: 0300 Not tainted (2.6.37-rc6+)
MSR: 9000000000001032 <ME,IR,DR> CR: 48044444 XER: 20000000
DAR: 00000001ffb9db50, DSISR: 0000000040000000
TASK = c00000003e1a00a0[2088] 'emacs' THREAD: c00000003e2f0000 CPU: 1
GPR00: 0000000000000001 c00000003e2f3d70 c00000000084e0d0 c0000000008816e8
GPR04: 000000001034c678 000000001032e8f9 0000000010336540 0000000040020000
GPR08: 0000000040020000 00000001ffb9db40 c00000003e2f3e30 0000000060000000
GPR12: 100000000000f032 c00000000fff0280 000000001032e8c9 0000000000000008
GPR16: 00000000105be9c0 00000000105be950 00000000105be9b0 00000000105be950
GPR20: 00000000ffb9dc50 00000000ffb9dbf0 00000000102f0000 00000000102f0000
GPR24: 00000000102e0000 00000000102f0000 0000000010336540 c0000000009ded38
GPR28: 00000000102e0000 c0000000000034d4 c0000000007ccb10 c00000003e2f3d70
NIP [c0000000000e1c00] .trace_hardirqs_off+0xb0/0x1d0
LR [c0000000000034d4] decrementer_common+0xd4/0x100
Call Trace:
[c00000003e2f3d70] [c00000003e2f3e30] 0xc00000003e2f3e30 (unreliable)
[c00000003e2f3e30] [c0000000000034d4] decrementer_common+0xd4/0x100
Instruction dump:
81690000 7f8b0000 419e0018 f84a0028 60000000 60000000 60000000 e95f0000
80030000 e92a0000 eb6301f8 2f800000 <eb890010> 41fe00dc a06d000a eb1e8050
---[ end trace 4ec7fd2be9240928 ]---
Reported-by: Joerg Sommer <joerg@alea.gnuu.de>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When we create an alternative feature section, the else case must be the
same size or smaller than the body. This is because when we patch the
else case in we just overwrite the body, so there must be room.
Up to now we just did this by inspection, but it's quite easy to enforce
it in the assembler, so we should.
The only change is to add the ifgt block, but that effects the alignment
of the tabs and so the whole macro is modified.
Also add a test, but #if 0 it because we don't want to break the build.
Anyone who's modifying the feature macros should enable the test.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
smp: Allow on_each_cpu() to be called while early_boot_irqs_disabled status to init/main.c
lockdep: Move early boot local IRQ enable/disable status to init/main.c
* akpm:
kernel/smp.c: consolidate writes in smp_call_function_interrupt()
kernel/smp.c: fix smp_call_function_many() SMP race
memcg: correctly order reading PCG_USED and pc->mem_cgroup
backlight: fix 88pm860x_bl macro collision
drivers/leds/ledtrig-gpio.c: make output match input, tighten input checking
MAINTAINERS: update Atmel AT91 entry
mm: fix truncate_setsize() comment
memcg: fix rmdir, force_empty with THP
memcg: fix LRU accounting with THP
memcg: fix USED bit handling at uncharge in THP
memcg: modify accounting function for supporting THP better
fs/direct-io.c: don't try to allocate more than BIO_MAX_PAGES in a bio
mm: compaction: prevent division-by-zero during user-requested compaction
mm/vmscan.c: remove duplicate include of compaction.h
memblock: fix memblock_is_region_memory()
thp: keep highpte mapped until it is no longer needed
kconfig: rename CONFIG_EMBEDDED to CONFIG_EXPERT
The meaning of CONFIG_EMBEDDED has long since been obsoleted; the option
is used to configure any non-standard kernel with a much larger scope than
only small devices.
This patch renames the option to CONFIG_EXPERT in init/Kconfig and fixes
references to the option throughout the kernel. A new CONFIG_EMBEDDED
option is added that automatically selects CONFIG_EXPERT when enabled and
can be used in the future to isolate options that should only be
considered for embedded systems (RISC architectures, SLOB, etc).
Calling the option "EXPERT" more accurately represents its intention: only
expert users who understand the impact of the configuration changes they
are making should enable it.
Reviewed-by: Ingo Molnar <mingo@elte.hu>
Acked-by: David Woodhouse <david.woodhouse@intel.com>
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: Greg KH <gregkh@suse.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Robin Holt <holt@sgi.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
virtio: remove virtio-pci root device
LGUEST_GUEST: fix unmet direct dependencies (VIRTUALIZATION && VIRTIO)
lguest: compile fixes
lguest: Use this_cpu_ops
lguest: document --rng in example Launcher
lguest: example launcher to use guard pages, drop PROT_EXEC, fix limit logic
lguest: --username and --chroot options
Fix sparse warning for non-ANSI function declaration:
arch/x86/xen/irq.c:129:30: warning: non-ANSI function declaration of function 'xen_init_irq_ops'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
During early boot, local IRQ is disabled until IRQ subsystem is
properly initialized. During this time, no one should enable
local IRQ and some operations which usually are not allowed with
IRQ disabled, e.g. operations which might sleep or require
communications with other processors, are allowed.
lockdep tracked this with early_boot_irqs_off/on() callbacks.
As other subsystems need this information too, move it to
init/main.c and make it generally available. While at it,
toggle the boolean to early_boot_irqs_disabled instead of
enabled so that it can be initialized with %false and %true
indicates the exceptional condition.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Pekka Enberg <penberg@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
LKML-Reference: <20110120110635.GB6036@htj.dyndns.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Honor the kconfig menu hierarchy to remove kconfig dependency warnings:
VIRTIO and VIRTIO_RING are subordinate to VIRTUALIZATION.
warning: (LGUEST_GUEST) selects VIRTIO which has unmet direct dependencies (VIRTUALIZATION)
warning: (LGUEST_GUEST && VIRTIO_PCI && VIRTIO_BALLOON) selects VIRTIO_RING which has unmet direct dependencies (VIRTUALIZATION && VIRTIO)
Reported-by: Toralf F_rster <toralf.foerster@gmx.de>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
arch/x86/lguest/boot.c: In function ‘lguest_init_IRQ’:
arch/x86/lguest/boot.c:824: error: macro "__this_cpu_write" requires 2 arguments, but only 1 given
arch/x86/lguest/boot.c:824: error: ‘__this_cpu_write’ undeclared (first use in this function)
arch/x86/lguest/boot.c:824: error: (Each undeclared identifier is reported only once
arch/x86/lguest/boot.c:824: error: for each function it appears in.)
drivers/lguest/x86/core.c: In function ‘copy_in_guest_info’:
drivers/lguest/x86/core.c:94: error: lvalue required as left operand of assignment
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Commit a4f740cf, "of/flattree: Add of_flat_dt_match() helper function"
introduced build failures in arch/powerpc/platform/83xx by mistyping
'static' as 'struct' in the compatible string list, and omitting a few
semicolons. This patch fixes it.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
In order to be able to suppress the use of SRAT tables that
32-bit Linux can't deal with (in one case known to lead to a
non-bootable system, unless disabling ACPI altogether), move the
"numa=" option handling to common code.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Reviewed-by: Thomas Renninger <trenn@suse.de>
Cc: Tejun Heo <tj@kernel.org>
Cc: Thomas Renninger <trenn@suse.de>
LKML-Reference: <4D36B581020000780002D0FF@vpn.id2.novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This reverts commit 86b1e8dd83 ("x86: Make relocatable kernel work with
new binutils").
Markus Trippelsdorf reported a boot failure caused by this patch.
The real solution to the original patch will likely involve an
arch-generic solution to define an overlaid jiffies_64 and jiffies
variables.
Until that's done and tested on all architectures revert this commit to
solve the regression.
Reported-and-bisected-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Acked-by: "H. Peter Anvin" <hpa@zytor.com>
Cc: Shaohua Li <shaohua.li@intel.com>
Cc: "Lu, Hongjiu" <hongjiu.lu@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>,
Cc: Sam Ravnborg <sam@ravnborg.org>
LKML-Reference: <4D36A759.60704@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Clear irqstack thread_info
x86: Make relocatable kernel work with new binutils
* 'upstream' of git://git.linux-mips.org/pub/scm/upstream-linus: (26 commits)
MIPS: Malta: enable Cirrus FB console
MIPS: add CONFIG_VIRTUALIZATION for virtio support
MIPS: Implement __read_mostly
MIPS: ath79: add common WMAC device for AR913X based boards
MIPS: ath79: Add initial support for the Atheros AP81 reference board
MIPS: ath79: add common SPI controller device
SPI: Add SPI controller driver for the Atheros AR71XX/AR724X/AR913X SoCs
MIPS: ath79: add common GPIO buttons device
MIPS: ath79: add common watchdog device
MIPS: ath79: add common GPIO LEDs device
MIPS: ath79: add initial support for the Atheros PB44 reference board
MIPS: ath79: utilize the MIPS multi-machine support
MIPS: ath79: add GPIOLIB support
MIPS: Add initial support for the Atheros AR71XX/AR724X/AR931X SoCs
MIPS: jump label: Add MIPS support.
MIPS: Use WARN() in uasm for better diagnostics.
MIPS: Optimize TLB handlers for Octeon CPUs
MIPS: Add LDX and LWX instructions to uasm.
MIPS: Use BBIT instructions in TLB handlers
MIPS: Declare uasm bbit0 and bbit1 functions.
...
While most users of a physical Malta board are using the serial port
as the console, a lot of QEMU users would prefer to interact with a
graphical console. Enable the Cirrus FB support in the Malta default
configuration to make that possible. Note that the default console will
still be the serial port, users have to pass "console=tty0" to the
kernel to use the Cirrus FB.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2001/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add CONFIG_VIRTUALIZATION to the MIPS architecture and include the
the virtio code there. Used to enable the virtio drivers under QEMU.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2002/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Just do what everyone else is doing by placing __read_mostly things in
the .data.read_mostly section.
mips_io_port_base can not be read-only (const) and writable
(__read_mostly) at the same time. One of them has to go, so I chose
to eliminate the __read_mostly. It will still get stuck in a portion
of memory that is not adjacent to things that are written, and thus
not be on a dirty cache line, for whatever that is worth.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/1702/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add common platform_device and helper code to make the registration
of the built-in wireless MAC easier on the Atheros AR9130/AR9132
based boards. Also register the WMAC device on the AR81 board.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: Imre Kaloz <kaloz@openwrt.org>,
Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Cc: Cliff Holden <Cliff.Holden@Atheros.com>
Cc: Kathy Giori <Kathy.Giori@Atheros.com>
Patchwork: https://patchwork.linux-mips.org/patch/1962/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Several boards are using the built-in SPI controller of the
AR71XX/AR724X/AR913X SoCs. This patch adds common platform_device
and helper code to register it. Additionally, the patch registers
the SPI bus on the PB44 board.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: Imre Kaloz <kaloz@openwrt.org>
Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Cc: Cliff Holden <Cliff.Holden@Atheros.com>
Cc: Kathy Giori <Kathy.Giori@Atheros.com>
Patchwork: https://patchwork.linux-mips.org/patch/1956/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The Atheros AR71XX/AR724X/AR913X SoCs have a built-in SPI controller. This
patch implements a driver for that.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: spi-devel-general@lists.sourceforge.net
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: linux-mips@linux-mips.org
Cc: Imre Kaloz <kaloz@openwrt.org>
Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Cc: Cliff Holden <Cliff.Holden@Atheros.com>
Cc: Kathy Giori <Kathy.Giori@Atheros.com>
Patchwork: https://patchwork.linux-mips.org/patch/1960/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Almost all boards have one or more push buttons connected to GPIO lines.
This patch adds common code to register a platform_device for them.
The patch also adds support for the buttons on the PB44 board.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Cc: Cliff Holden <Cliff.Holden@Atheros.com>
Cc: Kathy Giori <Kathy.Giori@Atheros.com>
Patchwork: https://patchwork.linux-mips.org/patch/1954/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
All supported SoCs have a built-in hardware watchdog driver. This patch
registers a platform_device for that to make it usable.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Cc: Cliff Holden <Cliff.Holden@Atheros.com>
Cc: Kathy Giori <Kathy.Giori@Atheros.com>
Patchwork: https://patchwork.linux-mips.org/patch/1955/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Almost all boards have one or more LEDs connected to GPIO lines. This
patch adds common code to register a platform_device for them.
The patch also adds support for the LEDs on the PB44 board.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Cc: Cliff Holden <Cliff.Holden@Atheros.com>
Cc: Kathy Giori <Kathy.Giori@Atheros.com>
Patchwork: https://patchwork.linux-mips.org/patch/1953/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch adds initial support for various Atheros SoCs based on the
MIPS 24Kc core. The following models are supported at the moment:
- AR7130
- AR7141
- AR7161
- AR9130
- AR9132
- AR7240
- AR7241
- AR7242
The current patch contains minimal support only, but the resulting
kernel can boot into user-space with using of an initramfs image on
various boards which are using these SoCs. Support for more built-in
devices and individual boards will be implemented in further patches.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Cc: Cliff Holden <Cliff.Holden@Atheros.com>
Cc: Kathy Giori <Kathy.Giori@Atheros.com>
Patchwork: https://patchwork.linux-mips.org/patch/1947/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
In order not to be left behind, we add jump label support for MIPS.
Tested on 64-bit big endian (Octeon), and 32-bit little endian
(malta/qemu).
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Jason Baron <jbaron@redhat.com>
Patchwork: https://patchwork.linux-mips.org/patch/1923/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
On the off chance that uasm ever warns about overflow, there is no way
to know what the offending instruction is.
Change the printks to WARNs, so we can get a nice stack trace. It has
the added benefit of being much more noticeable than the short single
line warning message, so is less likely to be ignored.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1905/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Octeon can use scratch registers in the TLB handlers. Octeon II can
use LDX instructions.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1904/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
If the CPU supports BBIT0 and BBIT1, use them in TLB handlers as they
are more efficient than an AND followed by an branch and then
restoring the clobbered register.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1873/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
these are already defined, but declaring them allow them to be used
outside of uasm.c.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1872/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch adds a generic solution to support multiple machines based on
a given SoC within a single kernel image. It is implemented already for
several other architectures but MIPS has no generic support for that yet.
[Ralf: This competes with DT but DT is a much more complex solution and this
code has been used by OpenWRT for a long time so for now DT is a bad reason
to stop the merge but longer term this should be migrated to DT.]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: kaloz@openwrt.org
Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Cc: Cliff Holden <Cliff.Holden@Atheros.com>
Patchwork: https://patchwork.linux-mips.org/patch/1814/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu: (25 commits)
m68knommu: fix broken setting of irq_chip and handler
m68knommu: switch to using -mcpu= flags for ColdFire targets
m68knommu: arch/m68knommu/Kconfig whitespace cleanup
m68knommu: create optimal separate instruction and data cache for ColdFire
m68knommu: support ColdFire caches that do copyback and write-through
m68knommu: support version 2 ColdFire split cache
m68knommu: make cache push code ColdFire generic
m68knommu: clean up ColdFire cache control code
m68knommu: move inclusion of ColdFire v4 cache registers
m68knommu: merge bit definitions for version 3 ColdFire cache controller
m68knommu: create bit definitions for the version 2 ColdFire cache controller
m68knommu: remove empty __iounmap() it is no used
m68knommu: remove kernel_map() code, it is not used
m68knommu: remove do_page_fault(), it is not used
m68knommu: use user stack pointer hardware on some ColdFire cores
m68knommu: remove command line printing DEBUG
m68knommu: remove fasthandler interrupt code
m68knommu: move UART addressing to part specific includes
m68knommu: fix clock rate value reported for ColdFire 54xx parts
m68knommu: move ColdFire CPU names into their headers
...
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf tools: Fix tracepoint id to string perf.data header table
perf tools: Fix handling of wildcards in tracepoint event selectors
powerpc: perf: Fix frequency calculation for overflowing counters
Mathias Merz reported that v2.6.37 failed to boot on his
system.
Make sure that the thread_info part of the irqstack is
initialized to zeroes.
Reported-and-Tested-by: Matthias Merz <linux@merz-ka.de>
Signed-off-by: Brian Gerst <brgerst@gmail.com>
Acked-by: Pekka Enberg <penberg@kernel.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
LKML-Reference: <AANLkTimyKXfJ1x8tgwrr1hYnNLrPfgE1NTe4z7L6tUDm@mail.gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The CONFIG_RELOCATABLE=y option is broken with new binutils, which will make
boot panic.
According to Lu Hongjiu, the affected binutils are from 2.20.51.0.12 to
2.21.51.0.3, which are release since Oct 22 this year. At least ubuntu 10.10 is
using such binutils. See:
http://sourceware.org/bugzilla/show_bug.cgi?id=12327
The reason of the boot panic is that we have 'jiffies = jiffies_64;' in
vmlinux.lds.S. The jiffies isn't in any section. In kernel build, there is
warning saying jiffies is an absolute address and can't be relocatable. At
runtime, jiffies will have virtual address 0.
Signed-off-by: Shaohua Li<shaohua.li@intel.com>
Cc: Lu Hongjiu<hongjiu.lu@intel.com>
Cc: Huang Ying <ying.huang@intel.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
LKML-Reference: <1295312269.1949.725.camel@sli10-conroe>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* git://git.infradead.org/mtd-2.6: (59 commits)
mtd: mtdpart: disallow reading OOB past the end of the partition
mtd: pxa3xx_nand: NULL dereference in pxa3xx_nand_probe
UBI: use mtd->writebufsize to set minimal I/O unit size
mtd: initialize writebufsize in the MTD object of a partition
mtd: onenand: add mtd->writebufsize initialization
mtd: nand: add mtd->writebufsize initialization
mtd: cfi: add writebufsize initialization
mtd: add writebufsize field to mtd_info struct
mtd: OneNAND: OMAP2/3: prevent regulator sleeping while OneNAND is in use
mtd: OneNAND: add enable / disable methods to onenand_chip
mtd: m25p80: Fix JEDEC ID for AT26DF321
mtd: txx9ndfmc: limit transfer bytes to 512 (ECC provides 6 bytes max)
mtd: cfi_cmdset_0002: add support for Samsung K8D3x16UxC NOR chips
mtd: cfi_cmdset_0002: add support for Samsung K8D6x16UxM NOR chips
mtd: nand: ams-delta: drop omap_read/write, use ioremap
mtd: m25p80: add debugging trace in sst_write
mtd: nand: ams-delta: select for built-in by default
mtd: OneNAND: lighten scary initial bad block messages
mtd: OneNAND: OMAP2/3: add support for command line partitioning
mtd: nand: rearrange ONFI revision checking, add ONFI 2.3
...
Fix up trivial conflict in drivers/mtd/Kconfig as per DavidW.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mattst88/alpha-2.6:
alpha: fix WARN_ON in __local_bh_enable()
alpha: fix breakage caused by df9ee29270
alpha: add GENERIC_HARDIRQS_NO__DO_IRQ to Kconfig
alpha/osf_sys: remove unused MAX_SELECT_SECONDS
alpha: change to new Makefile flag variables
alpha: kill off alpha_do_IRQ
alpha: irq clean up
alpha: use set_irq_chip and push down __do_IRQ to the machine types
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx: (63 commits)
ARM: PL08x: cleanup comments
Update CONFIG_MD_RAID6_PQ to CONFIG_RAID6_PQ in drivers/dma/iop-adma.c
ARM: PL08x: fix a warning
Fix dmaengine_submit() return type
dmaengine: at_hdmac: fix race while monitoring channel status
dmaengine: at_hdmac: flags located in first descriptor
dmaengine: at_hdmac: use subsys_initcall instead of module_init
dmaengine: at_hdmac: no need set ACK in new descriptor
dmaengine: at_hdmac: trivial add precision to unmapping comment
dmaengine: at_hdmac: use dma_address to program DMA hardware
pch_dma: support new device ML7213 IOH
ARM: PL08x: prevent dma_set_runtime_config() reconfiguring memcpy channels
ARM: PL08x: allow dma_set_runtime_config() to return errors
ARM: PL08x: fix locking between prepare function and submit function
ARM: PL08x: introduce 'phychan_hold' to hold on to physical channels
ARM: PL08x: put txd's on the pending list in pl08x_tx_submit()
ARM: PL08x: rename 'desc_list' as 'pend_list'
ARM: PL08x: implement unmapping of memcpy buffers
ARM: PL08x: store prep_* flags in async_tx structure
ARM: PL08x: shrink srcbus/dstbus in txd structure
...
When profiling a benchmark that is almost 100% userspace, I noticed some wildly
inaccurate profiles that showed almost all time spent in the kernel.
Closer examination shows we were programming a tiny number of cycles into the
PMU after each overflow (about ~200 away from the next overflow). This gets us
stuck in a loop which we eventually break out of by throttling the PMU (there
are regular throttle/unthrottle events in the log).
It looks like we aren't setting event->hw.last_period to something same and the
frequency to period calculations in perf are going haywire.
With the following patch we find the correct period after a few interrupts and
stay there. I also see no more throttle events.
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
LKML-Reference: <20110117161742.5feb3761@kryten>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Interrupts ought to be disabled _before_ irq_enter().
Signed-off-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: Matt Turner <mattst88@monolith.freenet-rz.de>
Commit df9ee29270 made arch_local_irq_save and arch_local_irq_restore
static inline which with -Werror trips up on __set_hae() and _set_hae()
which are extern inline. The naive solution is to make __set_hae() and
set_hae() static inline but for reasons described in commit d559d4a24a
this breaks the generic kernel build. Instead, since this is architecture
specific code, this patch hard wires in the architecture specific method
f disabling and enabling interrupts.
Tested-by: Michael Cree <mcree@orcon.net.nz>
Signed-off-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: Matt Turner <mattst88@gmail.com>
Remove the leftover from the commit 14e2acd868 ("select:
fix alpha OSF wrapper").
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Matt Turner <mattst88@gmail.com>
Good riddance... Nuke a pile of redundant handlers that the
generic code takes care of as well.
Tested-by: Michael Cree <mcree@orcon.net.nz>
Signed-off-by: Kyle McMartin <kyle@redhat.com>
Signed-off-by: Matt Turner <mattst88@gmail.com>
Stop touching irq_desc[irq] directly, instead use accessor
functions provided. Use irq_has_action instead of directly
testing the irq_desc.
Tested-by: Michael Cree <mcree@orcon.net.nz>
Signed-off-by: Kyle McMartin <kyle@redhat.com>
Signed-off-by: Matt Turner <mattst88@gmail.com>
Also kill superfluous IRQ_DISABLED initialization, since that's the
default state of the irq_desc[i].status field.
Tested-by: Michael Cree <mcree@orcon.net.nz>
Signed-off-by: Kyle McMartin <kyle@redhat.com>
Signed-off-by: Matt Turner <mattst88@gmail.com>
On PARISC, we have an include of linux/mm.h inside our asm/pgtable.h, so
this patch
commit 14fd403f21
Author: Andrea Arcangeli <aarcange@redhat.com>
Date: Thu Jan 13 15:46:37 2011 -0800
thp: export maybe_mkwrite
causes us an unsatisfiable use of pte_mkwrite in linux/mm.h.
The fix is to avoid including linux/mm.h in our pgtable.h, which
unbreaks the build.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Function ptep_test_and_clear_young have had wrong the first argument.
It is also necessary to add __HAVE macros for ptep_test_and_clear_young and
ptep_get_and_clear functions.
Error log:
In file included from linux/arch/microblaze/include/asm/pgtable.h:570,
from arch/microblaze/mm/pgtable.c:35:
include/asm-generic/pgtable.h:23: error: conflicting types for 'ptep_test_and_clear_young'
linux/arch/microblaze/include/asm/pgtable.h:449: error:
previous definition of 'ptep_test_and_clear_young' was here
include/asm-generic/pgtable.h:73: error: redefinition of 'ptep_get_and_clear'
linux/arch/microblaze/include/asm/pgtable.h:462: error:
previous definition of 'ptep_get_and_clear' was here
Signed-off-by: Michal Simek <monstr@monstr.eu>
Add missing linux/pagemap.h to solve compilation error.
Error log:
In file included from linux/arch/microblaze/include/asm/tlb.h:17,
from mm/pgtable-generic.c:9:
include/asm-generic/tlb.h: In function 'tlb_flush_mmu':
include/asm-generic/tlb.h:76: error: implicit declaration of function 'release_pages'
include/asm-generic/tlb.h: In function 'tlb_remove_page':
include/asm-generic/tlb.h:105: error: implicit declaration of function 'page_cache_release'
Signed-off-by: Michal Simek <monstr@monstr.eu>
The physical address is never used by the device tree code when
allocating memory for unflattening. Change the architecture's alloc
hook to return the virutal address instead.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
rcu: avoid pointless blocked-task warnings
rcu: demote SRCU_SYNCHRONIZE_DELAY from kernel-parameter status
rtmutex: Fix comment about why new_owner can be NULL in wake_futex_pi()
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, olpc: Add missing Kconfig dependencies
x86, mrst: Set correct APB timer IRQ affinity for secondary cpu
x86: tsc: Fix calibration refinement conditionals to avoid divide by zero
x86, ia64, acpi: Clean up x86-ism in drivers/acpi/numa.c
* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
timekeeping: Make local variables static
time: Rename misnamed minsec argument of clocks_calc_mult_shift()
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
tracing: Remove syscall_exit_fields
tracing: Only process module tracepoints once
perf record: Add "nodelay" mode, disabled by default
perf sched: Fix list of events, dropping unsupported ':r' modifier
Revert "perf tools: Emit clearer message for sys_perf_event_open ENOENT return"
perf top: Fix annotate segv
perf evsel: Fix order of event list deletion
* 'fixes' of master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: fix missing branch in __error_a
ARM: fix /proc/$PID/stack on SMP
ARM: Fix build regression on SA11x0, PXA, and H720x targets
ARM: 6625/1: use memblock memory regions for "System RAM" I/O resources
ARM: fix wrongly patched constants
ARM: 6624/1: fix dependency for CONFIG_SMP_ON_UP
ARM: 6623/1: Thumb-2: Fix out-of-range offset for Thumb-2 in proc-v7.S
ARM: 6622/1: fix dma_unmap_sg() documentation
ARM: 6621/1: bitops: remove condition code clobber for CLZ
ARM: 6620/1: Change misleading warning when CONFIG_CMDLINE_FORCE is used
ARM: 6619/1: nommu: avoid mapping vectors page when !CONFIG_MMU
ARM: sched_clock: make minsec argument to clocks_calc_mult_shift() zero
ARM: sched_clock: allow init_sched_clock() to be called early
ARM: integrator: fix compile warning in cpu.c
ARM: 6616/1: Fix ep93xx-fb init/exit annotations
ARM: twd: fix display of twd frequency
ARM: udelay: prevent math rounding resulting in short udelays
on Parisc, we have an include of linux/mm.h inside our asm/pgtable.h, so
this patch
commit 14fd403f21
Author: Andrea Arcangeli <aarcange@redhat.com>
Date: Thu Jan 13 15:46:37 2011 -0800
thp: export maybe_mkwrite
Causes us an unsatisfiable use of pte_mkwrite in linux/mm.h
The fix is obviously not to include linux/mm.h in our pgtable.h, which
unbreaks the build.
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Remove the broken line wrapping handling in pdc_iodc_print().
It is broken in 3 ways :
- It doesn't keep track of the current screen position, it just
assumes that the new buffer will be printed at the begining of the
screen.
- It doesn't take in account that non printable characters won't
increase the current position on the screen.
- And last but not least, it triggers a kernel panic if a backspace
is the first char in the provided buffer :
Backtrace:
[<0000000040128ec4>] pdc_console_write+0x44/0x78
[<0000000040128f18>] pdc_console_tty_write+0x20/0x38
[<000000004032f1ac>] n_tty_write+0x2a4/0x550
[<000000004032b158>] tty_write+0x1e0/0x2d8
[<00000000401bb420>] vfs_write+0xb8/0x188
[<00000000401bb630>] sys_write+0x68/0xb8
[<0000000040104eb8>] syscall_exit+0x0/0x14
Most terminals handle the line wrapping just fine. I've confirmed that
it works correctly on a C8000 with both vga and serial output.
Signed-off-by: Guy Martin <gmsoft@tuxicoman.be>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
When DEBUG_LL is not set, we don't want __error_a re-entering
__lookup_machine_type - we want it to go to the error function. This
used to be the case before we reorganized the layout for hotplug cpu,
as we used to fall through to __error. With the changed layout, we
need an explicit branch here instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
