Manually tracking an active collection to set collection parents is not
necessary, we just have to look one step back into the collection stack
to find the correct parent.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
A Goodix touchpad doesn't work. Touching the touchpad can trigger IRQ
but there's no input event from HID subsystem.
Turns out it reports some invalid data:
[ 22.136630] i2c_hid i2c-DELL091F:00: input: 0b 00 01 00 00 00 00 00 00 00 00
After some trial and error, it's another device that doesn't work well
with ON/SLEEP commands. Disable runtime PM to fix the issue.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Previously, the pointer to the parent collection was stored. If a device
exceeds 16 collections (HID_DEFAULT_NUM_COLLECTIONS), the array to store
the collections is reallocated, the pointer to the parent collection becomes
invalid.
Replace the pointers with an index-based lookup into the collections array.
Fixes: c53431eb69 ("HID: core: store the collections as a basic tree")
Reported-by: Pandruvada, Srinivas <srinivas.pandruvada@intel.com>
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Tested-by: Kyle Pelton <kyle.d.pelton@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Pull HID updates from Jiri Kosina:
- high-resolution scrolling support that gracefully handles differences
between MS and Logitech implementations in HW, from Peter Hutterer
and Harry Cutts
- MSI IRQ support for intel-ish driver, from Song Hongyan
- support for new hardware (Cougar 700K, Odys Winbook 13, ASUS FX503VD,
ASUS T101HA) from Daniel M. Lambea, Hans de Goede and Aleix Roca
Nonell
- other small assorted fixups
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid: (22 commits)
HID: i2c-hid: Add Odys Winbook 13 to descriptor override
HID: lenovo: Add checks to fix of_led_classdev_register
HID: intel-ish-hid: add MSI interrupt support
HID: debug: Change to use DEFINE_SHOW_ATTRIBUTE macro
HID: doc: fix wrong data structure reference for UHID_OUTPUT
HID: intel-ish-hid: fixes incorrect error handling
HID: asus: Add support for the ASUS T101HA keyboard dock
HID: logitech: Use LDJ_DEVICE macro for existing Logitech mice
HID: logitech: Enable high-resolution scrolling on Logitech mice
HID: logitech: Add function to enable HID++ 1.0 "scrolling acceleration"
HID: logitech-hidpp: fix typo, hiddpp to hidpp
HID: input: use the Resolution Multiplier for high-resolution scrolling
HID: core: process the Resolution Multiplier
HID: core: store the collections as a basic tree
Input: add `REL_WHEEL_HI_RES` and `REL_HWHEEL_HI_RES`
HID: input: support Microsoft wireless radio control hotkey
HID: use macros in IS_INPUT_APPLICATION
HID: asus: Add support for the ASUS FX503VD laptop
HID: asus: Add event handler to catch unmapped Asus Vendor UsagePage codes
HID: cougar: Add support for Cougar 700K Gaming Keyboard
...
The Odys Winbook 13 uses a SIPODEV SP1064 touchpad, which does not
supply descriptors, add this to the DMI descriptor override list, fixing
the touchpad not working.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1526312
Reported-by: Rene Wagner <redhatbugzilla@callerid.de>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
In lenovo_probe_tpkbd(), the function of_led_classdev_register() could
return an error value that is unchecked. The fix adds these checks.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Core changes:
- Some core changes are already in outside of this pull
request as they came through the regulator tree, most
notably devm_gpiod_unhinge() that removes devres refcount
management from a GPIO descriptor. This is needed in
subsystems such as regulators where the regulator core
need to take over the reference counting and lifecycle
management for a GPIO descriptor.
- We dropped devm_gpiochip_remove() and devm_gpio_chip_match()
as nothing needs it. We can bring it back if need be.
- Add a global TODO so people see where we are going. This
helps setting the direction now that we are two GPIO
maintainers.
- Handle the MMC CD/WP properties in the device tree core.
(The bulk of patches activating this code is already
merged through the MMC/SD tree.)
- Augment gpiochip_request_own_desc() to pass a flag so
we as gpiochips can request lines as active low or open
drain etc even from ourselves.
New drivers:
- New driver for Cadence GPIO blocks.
- New driver for Atmel SAMA5D2 PIOBU GPIO lines.
Driver improvements:
- A major refactoring of the PCA953x driver - this driver has
been around for ages, and is now modernized to reduce code
duplication that has stacked up and is using regmap to read
write and cache registers.
- Intel drivers are now maintained in a separate tree and
start with a round of cleanups and unifications.
-----BEGIN PGP SIGNATURE-----
iQIcBAABAgAGBQJcJJcmAAoJEEEQszewGV1zdCoQAMSLPh+4QdYLFS3ZmnsPvZkg
Zkz94RVT+uLLmHpR8XBl0wl4mmYCiwB50IwsXwlvJGceSXjCn6hLg9BZBP5hFMCb
yFk3fgXQSh7TOnpjgbCWSssCjpejQ0cOb/2nWHz5s/fbYKYlh3VXckW9hhW+R+b3
6+Mno1SzmBkpVVQ21ISlZeLoNDynkCW6DfjiKMuHAyxzxa0oZ9Qid+tnVDnQM4rD
rCnvYLuvxlXw97W+LI7AU9KoCITdO+2M/0dtGVEEYKfHseRReSy2Oo3nlqCglygX
cNkBe9RYU1CJdas1P/c18wjDAqWp/pbugzHDkYF5Y3tBtB2rQSftjtnQngiVMXMt
De7ejPvL7/OLECvI2WUD6y9NAduw/HE4FO8BBdn0gP/a9svJpVZ993yPd3F9n7EZ
ZIBpycDZVtkcE7dwQgek17bFILRY5nBBMB9oCLL2wk48qdmjpcAbxVfGSsYOe6wO
+cZRZuj/eR3i9gHRugfFx7Evoc7l4erihTpES/YAy3De1s3uV8KjT4zE7Jh+M9LW
GM797BcXJJeb5toC7HZ/G2UAVMyWEhY0n7PGG616CS8IrzmzIZpJOL9kUVOWPb0F
9CPt6qhVbUl9rxp1H/Z3TxvYqIw6icn/z5YewZxLU1zaBlpE3jc7PhZb5hOGnFUf
/DWwe4n99JsjHTrGx1ra
=05LW
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.21-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.21 kernel series.
Core changes:
- Some core changes are already in outside of this pull request as
they came through the regulator tree, most notably
devm_gpiod_unhinge() that removes devres refcount management from a
GPIO descriptor. This is needed in subsystems such as regulators
where the regulator core need to take over the reference counting
and lifecycle management for a GPIO descriptor.
- We dropped devm_gpiochip_remove() and devm_gpio_chip_match() as
nothing needs it. We can bring it back if need be.
- Add a global TODO so people see where we are going. This helps
setting the direction now that we are two GPIO maintainers.
- Handle the MMC CD/WP properties in the device tree core. (The bulk
of patches activating this code is already merged through the
MMC/SD tree.)
- Augment gpiochip_request_own_desc() to pass a flag so we as
gpiochips can request lines as active low or open drain etc even
from ourselves.
New drivers:
- New driver for Cadence GPIO blocks.
- New driver for Atmel SAMA5D2 PIOBU GPIO lines.
Driver improvements:
- A major refactoring of the PCA953x driver - this driver has been
around for ages, and is now modernized to reduce code duplication
that has stacked up and is using regmap to read write and cache
registers.
- Intel drivers are now maintained in a separate tree and start with
a round of cleanups and unifications"
* tag 'gpio-v4.21-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (99 commits)
gpio: sama5d2-piobu: Depend on OF_GPIO
gpio: Add Cadence GPIO driver
dt-bindings: gpio: Add bindings for Cadence GPIO
gpiolib-acpi: remove unused variable 'err', cleans up build warning
gpio: mxs: read pin level directly instead of using .get
gpio: aspeed: remove duplicated statement
gpio: add driver for SAMA5D2 PIOBU pins
dt-bindings: arm: atmel: describe SECUMOD usage as a GPIO controller
gpio/mmc/of: Respect polarity in the device tree
dt-bindings: gpio: rcar: Add r8a774c0 (RZ/G2E) support
memory: omap-gpmc: Get the header of the enum
ARM: omap1: Fix new user of gpiochip_request_own_desc()
gpio: pca953x: Add regmap dependency for PCA953x driver
gpio: raspberrypi-exp: decrease refcount on firmware dt node
gpiolib: Fix return value of gpio_to_desc() stub if !GPIOLIB
gpio: pca953x: Restore registers after suspend/resume cycle
gpio: pca953x: Zap single use of pca953x_read_single()
gpio: pca953x: Zap ad-hoc reg_output cache
gpio: pca953x: Zap ad-hoc reg_direction cache
gpio: pca953x: Perform basic regmap conversion
...
Now ish hid ipc only support sideband interrupt but on some platforms
they use MSI interrupt.
In order to make the interrupt type coverage all the scenario add
single MSI interrupt support, it can match all interrupt types.
Signed-off-by: Song Hongyan <hongyan.song@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The memory chunk allocated by hid_allocate_device() should be released
by hid_destroy_device(), not kfree().
Fixes: 0b28cb4bcb1("HID: intel-ish-hid: ISH HID client driver")
Signed-off-by: Pan Bian <bianpan2016@163.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The ASUS T101HA keyboard dock generates HID events using the ASUS vendor
specific UsagePage 0xff31. In consequence, some multimedia keys such as
brightness up and down are not working with hid-generic.
This commit adds the T101HA dock into the supported device list of the
hid-asus driver. It also prevents the dock's integrated touchpad to be
bound with hid-asus given that it is already working fine with
hid-multitouch.
Signed-off-by: Aleix Roca Nonell <kernelrocks@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Before things go out of hand, make it possible to pass
flags when requesting "own" descriptors from a gpio_chip.
This is necessary if the chip wants to request a GPIO with
active low semantics, for example.
Cc: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Roger Quadros <rogerq@ti.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pull HID subsystem fixes from Jiri Kosina:
- two device-specific quirks from Hans de Goede and Nic Soudée
- reintroduction of (mistakenly remocved) ABS_RESERVED from Peter
Hutterer
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid:
Input: restore EV_ABS ABS_RESERVED
HID: quirks: fix RetroUSB.com devices
HID: ite: Add USB id match for another ITE based keyboard rfkill key quirk
Signed-off-by: Harry Cutts <hcutts@chromium.org>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Verified-by: Harry Cutts <hcutts@chromium.org>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
There are three features used by various Logitech mice for
high-resolution scrolling: the scrolling acceleration bit in HID++ 1.0,
and the x2120 and x2121 features in HID++ 2.0 and above. This patch
supports all three, and uses the multiplier reported by the mouse for
the HID++ 2.0+ features.
The full list of product IDs of mice which support high-resolution
scrolling was provided by Logitech, but the patch was tested using the
following mice (using the Unifying receiver):
* HID++ 1.0: Anywhere MX, Performance MX
* x2120: M560
* x2121: MX Anywhere 2, MX Master 2S
This patch is a combinations of the now-reverted commits 1ff2e1a44e,
d56ca9855b, 5fe2ccbef9, 044ee89028 together with some extra bits for the
directional and timeout-based reset.
The previous patch series was in hid-input, it appears this remainder
handling is logitech-specific and was moved to hid-logitech-hidpp.c and
renamed accordingly.
Signed-off-by: Harry Cutts <hcutts@chromium.org>
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Verified-by: Harry Cutts <hcutts@chromium.org>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
"Scrolling acceleration" is a bit of a misnomer: it doesn't deal with
acceleration at all. However, that's the name used in Logitech's spec,
so I used it here.
Signed-off-by: Harry Cutts <hcutts@chromium.org>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Verified-by: Harry Cutts <hcutts@chromium.org>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Verified-by: Harry Cutts <hcutts@chromium.org>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Windows uses a magic number of 120 for a wheel click. High-resolution
scroll wheels are supposed to use a fraction of 120 to signal smaller
scroll steps. This is implemented by the Resolution Multiplier in the
device itself.
If the multiplier is present in the report descriptor, set it to the
logical max and then use the resolution multiplier to calculate the
high-resolution events. This is the recommendation by Microsoft, see
http://msdn.microsoft.com/en-us/windows/hardware/gg487477.aspx
Note that all mice encountered so far have a logical min/max of 0/1, so
it's a binary "yes or no" to high-res scrolling anyway.
To make userspace simpler, always enable the REL_WHEEL_HI_RES bit. Where
the device doesn't support high-resolution scrolling, the value for the
high-res data will simply be a multiple of 120 every time. For userspace,
if REL_WHEEL_HI_RES is available that is the one to be used.
Potential side-effect: a device with a Resolution Multiplier applying to
other Input items will have those items set to the logical max as well.
This cannot easily be worked around but it is doubtful such devices exist.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Verified-by: Harry Cutts <hcutts@chromium.org>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
The Resolution Multiplier is a feature report that modifies the value of
Usages within the same Logical Collection. If the multiplier is set to
anything but 1, the hardware reports (value * multiplier) for the same amount
of physical movement, i.e. the value we receive in the kernel is
pre-multiplied.
The hardware may either send a single (value * multiplier), or by sending
multiplier as many reports with the same value, or a combination of these two
options. For example, when the Microsoft Sculpt Ergonomic mouse Resolution
Multiplier is set to 12, the Wheel sends out 12 for every detent but AC Pan
sends out a value of 3 at 4 times the frequency.
The effective multiplier is based on the physical min/max of the multiplier
field, a logical min/max of [0,1] with a physical min/max of [1,8] means the
multiplier is either 1 or 8.
The Resolution Multiplier was introduced for high-resolution scrolling in
Windows Vista and is commonly used on Microsoft mice.
The recommendation for the Resolution Multiplier is to default to 1 for
backwards compatibility. This patch adds an arbitrary upper limit at 255. The
only known use case for the Resolution Multiplier is for scroll wheels where the
multiplier has to be a fraction of 120 to work with Windows.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Verified-by: Harry Cutts <hcutts@chromium.org>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
For each collection parsed, store a pointer to the parent collection
(if any). This makes it a lot easier to look up which collection(s)
any given item is part of
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Verified-by: Harry Cutts <hcutts@chromium.org>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
SNES RetroPort and RetroPad register only 4 gamepad buttons
when they should register all 8 buttons. This is described here:
https://ask.fedoraproject.org/en/question/128102
This is happening because of:
Commit 190d7f02ce ("HID: input: do not increment usages when
duplicate is found")
Here, I add the quirk HID_QUIRK_INCREMENT_USAGE_ON_DUPLICATE
(created for backward compatibility with the change in 190d7f02ce)
for the two products.
Tested with both RetroPort and RetroPad.
Cc: stable@vger.kernel.org # v4.18+
Signed-off-by: Nic Soudée <nsoudee@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Pull input updates from Dmitry Torokhov:
"Mostly new IDs for Elan/Synaptics touchpads, plus a few small fixups"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: omap-keypad - fix keyboard debounce configuration
Input: xpad - quirk all PDP Xbox One gamepads
Input: synaptics - enable SMBus for HP 15-ay000
Input: synaptics - add PNP ID for ThinkPad P50 to SMBus
Input: elan_i2c - add ACPI ID for Lenovo IdeaPad 330-15ARR
Input: elan_i2c - add support for ELAN0621 touchpad
Input: hyper-v - fix wakeup from suspend-to-idle
Input: atkbd - clean up indentation issue
Input: st1232 - convert to SPDX identifiers
Input: migor_ts - convert to SPDX identifiers
Input: dt-bindings - fix a typo in file input-reset.txt
Input: cros_ec_keyb - fix button/switch capability reports
Input: elan_i2c - add ELAN0620 to the ACPI table
Input: matrix_keypad - check for errors from of_get_named_gpio()
Here are some small IIO and Staging driver fixes for 4.20-rc5.
Nothing major, the IIO fix ended up touching the HID drivers at the same
time, but the HID maintainer acked it. The staging fixes are all minor
patches for reported issues and regressions, full details are in the
shortlog.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXAFeeA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykZSQCgm8wafCzK2b9YjeUmAxFJQCKkK7YAnjHSqa8N
FwSpP/zei0mtZgw6Rzj9
=cBhw
-----END PGP SIGNATURE-----
Merge tag 'staging-4.20-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging and IIO driver fixes from Greg KH:
"Here are some small IIO and staging driver fixes for 4.20-rc5.
Nothing major, the IIO fix ended up touching the HID drivers at the
same time, but the HID maintainer acked it. The staging fixes are all
minor patches for reported issues and regressions, full details are in
the shortlog.
All of these have been in linux-next for a while with no reported
issues"
* tag 'staging-4.20-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
iio/hid-sensors: Fix IIO_CHAN_INFO_RAW returning wrong values for signed numbers
staging: vchiq_arm: fix compat VCHIQ_IOC_AWAIT_COMPLETION
staging: mt7621-pinctrl: fix uninitialized variable ngroups
staging: rtl8723bs: Add missing return for cfg80211_rtw_get_station
staging: most: use format specifier "%s" in snprintf
staging: rtl8723bs: Fix incorrect sense of ether_addr_equal
staging: mt7621-dma: fix potentially dereferencing uninitialized 'tx_desc'
staging: comedi: clarify/unify macros for NI macro-defined terminals
drivers: staging: cedrus: find ctx before dereferencing it ctx
staging: rtl8723bs: Fix the return value in case of error in 'rtw_wx_read32()'
staging: comedi: ni_mio_common: scale ao INSN_CONFIG_GET_CMD_TIMING_CONSTRAINTS
iio:st_magn: Fix enable device after trigger
The ASUS FX503VD laptop uses an USB keyboard with several hotkeys
which use the Asus Vendor specific UsagePage.
This uses two usage-codes within the page which have not been seen
before, 0x7c for its mic-mute hotkey and 0x99 for Fn+F5 which has
a "fan" symbol as hotkey symbol on the keyb. we map this to KEY_PROG4
(PROG1-PROG3 are already used).
This commit adds the mappings for the 2 new usage codes and the USB-ids
for this keyboard to the hid-asus driver.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Various Asus devices generate HID events using the Asus Vendor specific
UsagePage 0xff31 and hid-asus will map these in its input_mapping for all
devices to which it binds (independent of any quirks).
Add an event callback which check for unmapped (because sofar unknown)
usages within the Asus Vendor UsagePage and log a warning for these.
The purpose of this patch is to help debugging / find such unmapped codes
and add them to the asus_input_mapping() function.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
The 258a:6a88 keyboard-dock shipped with the Prowise PT301 tablet is
likely another ITE based design. The controller die is directly bonded
to the PCB with a blob of black glue on top so there are no markings and
the 258a vendor-id used is unknown anywhere. But the keyboard has the
exact same hotkeys mapped to Fn+F1 - F10 as the other ITE8595 keyboard
I have *and* it has the same quirky behavior wrt the rfkill hotkey.
Either way as said this keyboard has the same quirk for its rfkill /
airplane mode hotkey as the ITE 8595 chip, it only sends a single release
event when pressed and released, it never sends a press event.
This commit adds the 258a:6a88 USB id to the hid-ite id-table, fixing
the rfkill key not working on this keyboard.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
* st_magn
- Avoid an ordering issue that lead to large numbers of unhandled
interrupts whilst enabling buffered capture.
* hid-sensors
- Fix a long running problem with signed values reading wrong from
sysfs on these sensors. It appears people were only using the
buffered interface. These typically occur in laptops so chances
are everyone was using the sensor-proxy which will use the buffered
interface by default.
-----BEGIN PGP SIGNATURE-----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=nVLE
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-4.20a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First set of IIO fixes for the 4.20 cycle.
* st_magn
- Avoid an ordering issue that lead to large numbers of unhandled
interrupts whilst enabling buffered capture.
* hid-sensors
- Fix a long running problem with signed values reading wrong from
sysfs on these sensors. It appears people were only using the
buffered interface. These typically occur in laptops so chances
are everyone was using the sensor-proxy which will use the buffered
interface by default.
* tag 'iio-fixes-for-4.20a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio:
iio/hid-sensors: Fix IIO_CHAN_INFO_RAW returning wrong values for signed numbers
iio:st_magn: Fix enable device after trigger
This reverts commit 1ff2e1a44e.
It turns out the current API is not that compatible with
some Microsoft mice, so better start again from scratch.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Harry Cutts <hcutts@chromium.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Jiri Kosina <jkosina@suse.cz>
This reverts commit 051dc9b057.
It turns out the current API is not that compatible with
some Microsoft mice, so better start again from scratch.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Harry Cutts <hcutts@chromium.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Jiri Kosina <jkosina@suse.cz>
This reverts commit d56ca9855b.
It turns out the current API is not that compatible with
some Microsoft mice, so better start again from scratch.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Harry Cutts <hcutts@chromium.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Jiri Kosina <jkosina@suse.cz>
This reverts commit 3fe1d6bbcd.
It turns out the current API is not that compatible with
some Microsoft mice, so better start again from scratch.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Harry Cutts <hcutts@chromium.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Jiri Kosina <jkosina@suse.cz>
This reverts commit 5fe2ccbef9.
It turns out the current API is not that compatible with
some Microsoft mice, so better start again from scratch.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Harry Cutts <hcutts@chromium.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Jiri Kosina <jkosina@suse.cz>
This reverts commit 044ee89028.
It turns out the current API is not that compatible with
some Microsoft mice, so better start again from scratch.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Harry Cutts <hcutts@chromium.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Add USB ID 060b:700a to the list of valid USB IDS for the
cougar hid driver.
Signed-off-by: Daniel M. Lambea <dmlambea@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
The PixArt OEM mice are known for disconnecting every minute in
runlevel 1 or 3 if they are not always polled. So add quirk
ALWAYS_POLL for two Primax mice as well.
0x4e22 is the Dell MS111-P and 0x4d0f is the unbranded HP Portia
mouse HP 697738-001. Both were built until approx. 2014.
Those were the standard mice from those vendors and are still
around - even as new old stock.
Reference: https://github.com/sriemer/fix-linux-mouse/issues/11
Signed-off-by: Sebastian Parschauer <sparschauer@suse.de>
CC: stable@vger.kernel.org
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
LG touchscreen (1fd2:8001) stops working after reboot:
[ 4.859153] i2c_hid i2c-SAPS2101:00: i2c_hid_get_input: incomplete report (64/66)
[ 4.936070] i2c_hid i2c-SAPS2101:00: i2c_hid_get_input: incomplete report (64/66)
[ 9.948224] i2c_hid i2c-SAPS2101:00: failed to reset device.
The device in question stops working after receives SLEEP, ON, SLEEP
commands in a short period. The scenario is like this:
- Once the desktop session closes, it also closed the hid device, so the
device gets runtime suspended and receives a SLEEP command.
- Before calling shutdown callback, it gets runtime resumed and received
an ON command.
- In the shutdown callback, it receives another SLEEP command.
I failed to find a reliable interval between ON/SLEEP commands that can
make it work, so let's simply disable runtime PM for the device.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Cirque Touchpad/Pointstick combo is similar to Alps devices, it requires
MT_CLS_WIN_8_DUAL to expose its pointstick as a mouse.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Previously, when a HID client such as the Steam Client was running, this
driver disabled its input device to avoid doubling the input events.
While it worked mostly fine, some games got confused by the idle gamepad,
and switched to two player mode, or asked the user to choose which gamepad
to use. Other games just crashed, probably a bug in Unity [1].
With this commit, when a HID client starts, the input device is removed;
when the HID client ends the input device is recreated.
[1]: https://github.com/ValveSoftware/steam-for-linux/issues/5645
Signed-off-by: Rodrigo Rivas Costa <rodrigorivascosta@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This reverts commit 336fd4f5f2.
Please note that `strlcpy()` does *NOT* do what you think it does.
strlcpy() *ALWAYS* reads the full input string, regardless of the
'length' parameter. That is, if the input is not zero-terminated,
strlcpy() will *READ* beyond input boundaries. It does this, because it
always returns the size it *would* copy if the target was big enough,
not the truncated size it actually copied.
The original code was perfectly fine. The hid device is
zero-initialized and the strncpy() functions copied up to n-1
characters. The result is always zero-terminated this way.
This is the third time someone tried to replace strncpy with strlcpy in
this function, and gets it wrong. I now added a comment that should at
least make people reconsider.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When a UHID_CREATE command is written to the uhid char device, a
copy_from_user() is done from a user pointer embedded in the command.
When the address limit is KERNEL_DS, e.g. as is the case during
sys_sendfile(), this can read from kernel memory. Alternatively,
information can be leaked from a setuid binary that is tricked to write
to the file descriptor. Therefore, forbid UHID_CREATE in these cases.
No other commands in uhid_char_write() are affected by this bug and
UHID_CREATE is marked as "obsolete", so apply the restriction to
UHID_CREATE only rather than to uhid_char_write() entirely.
Thanks to Dmitry Vyukov for adding uhid definitions to syzkaller and to
Jann Horn for commit 9da3f2b740 ("x86/fault: BUG() when uaccess
helpers fault on kernel addresses"), allowing this bug to be found.
Reported-by: syzbot+72473edc9bf4eb1c6556@syzkaller.appspotmail.com
Fixes: d365c6cfd3 ("HID: uhid: add UHID_CREATE and UHID_DESTROY events")
Cc: <stable@vger.kernel.org> # v3.6+
Cc: Jann Horn <jannh@google.com>
Cc: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Reviewed-by: Jann Horn <jannh@google.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Before this commit sensor_hub_input_attr_get_raw_value() failed to take
the signedness of 16 and 8 bit values into account, returning e.g.
65436 instead of -100 for the z-axis reading of an accelerometer.
This commit adds a new is_signed parameter to the function and makes all
callers pass the appropriate value for this.
While at it, this commit also fixes up some neighboring lines where
statements were needlessly split over 2 lines to improve readability.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
It makes little sense but still possible to put Hyper-V guests into
suspend-to-idle state. To wake them up two wakeup sources were registered
in the past: hyperv-keyboard and hid-hyperv. However, since
commit eed4d47efe ("ACPI / sleep: Ignore spurious SCI wakeups from
suspend-to-idle") pm_wakeup_event() from these devices is ignored. Switch
to pm_wakeup_hard_event() API as these devices are actually the only
possible way to wakeup Hyper-V guests.
Fixes: eed4d47efe (ACPI / sleep: Ignore spurious SCI wakeups from suspend-to-idle)
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: K. Y. Srinivasan <kys@microsoft.com>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
lockdep is much more powerful enforcing the locking rules than code comments,
so let's switch to it.
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Motorola/Zebra Symbol DS4308-HD is a handheld USB barcode scanner
which does not have a battery, but reports one anyway that always has
capacity 2.
Let's apply the IGNORE quirk to prevent it from being treated like a
power supply so that userspaces don't get confused that this
accessory is almost out of power and warn the user that they need to charge
their wired barcode scanner.
Reported here: https://bugs.chromium.org/p/chromium/issues/detail?id=804720
Signed-off-by: Benson Leung <bleung@chromium.org>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
asus_wmi_evaluate_method() is an empty dummy function when CONFIG_ASUS_WMI
is disabled, or not reachable from a built-in device driver. This leads to
a theoretical evaluation of an uninitialized variable that the compiler
complains about, failing to check that the hardcoded return value makes
this an unreachable code path:
In file included from include/linux/printk.h:336,
from include/linux/kernel.h:14,
from include/linux/list.h:9,
from include/linux/dmi.h:5,
from drivers/hid/hid-asus.c:29:
drivers/hid/hid-asus.c: In function 'asus_input_configured':
include/linux/dynamic_debug.h:135:3: error: 'value' may be used uninitialized in this function [-Werror=maybe-uninitialized]
__dynamic_dev_dbg(&descriptor, dev, fmt, \
^~~~~~~~~~~~~~~~~
drivers/hid/hid-asus.c:359:6: note: 'value' was declared here
u32 value;
^~~~~
With an extra IS_ENABLED() check, the warning goes away.
Fixes: 3b692c55e5 ("HID: asus: only support backlight when it's not driven by WMI")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Pull in a merge commit that brought in 3b692c55e5 ("HID: asus: only
support backlight when it's not driven by WMI") so that fixup could be
applied on top of it.
Move the Dell dcdbas and dell_rbu drivers into platform/drivers/x86 as
they are closely coupled with other drivers in this location.
Improve _init* usage for acerhdf and fix some usage issues with messages
and module parameters.
Simplify asus-wmi by calling ACPI/WMI methods directly, eliminating
workqueue overhead, eliminate double reporting of keyboard backlight.
Fix wake from USB failure on Bay Trail devices (intel_int0002_vgpio).
Notify intel_telemetry users when IPC1 device is not enabled.
Update various drivers with new laptop model IDs.
Update several intel drivers to use SPDX identifers and order headers
alphabetically.
The following is an automated git shortlog grouped by driver:
Add Intel AtomISP2 dummy / power-management driver:
- Add Intel AtomISP2 dummy / power-management driver
lg-laptop:
- Add LG Gram laptop special features driver
HID:
- asus: only support backlight when it's not driven by WMI
MAINTAINERS:
- intel_telemetry: Update maintainers info
- intel_pmc_core: Update MAINTAINERS
- Update maintainer for dcdbas and dell_rbu
- Use my infradead account exclusively for PDx86 work
acerhdf:
- restructure to allow large BIOS table be __initconst
- mark appropriate content with __init prefix
- Add BIOS entry for Gateway LT31 v1.3307
- Remove cut-and-paste trap from instructions
- Enable ability to list supported systems
- clarify modinfo messages for BIOS override
asus-wmi:
- export function for evaluating WMI methods
- Only notify kbd LED hw_change by fn-key pressed
- Simplify the keyboard brightness updating process
firmware:
- dcdbas: include linux/io.h
- dcdbas: Move dcdbas to drivers/platform/x86
- dell_rbu: Move dell_rbu to drivers/platform/x86
- dcdbas: Add support for WSMT ACPI table
- dell_rbu: Make payload memory uncachable
ideapad-laptop:
- Add Y530-15ICH to no_hw_rfkill
- Use __func__ instead of read_ec_cmd in pr_err
intel-hid:
- Convert to use SPDX identifier
intel-ips:
- Convert to use SPDX identifier
intel-rst:
- Convert to use SPDX identifier
- Sort headers alphabetically
intel-smartconnect:
- Convert to use SPDX identifier
- Sort headers alphabetically
intel-wmi-thunderbolt:
- Add dynamic debugging
- Convert to use SPDX identifier
intel_bxtwc_tmu:
- Convert to use SPDX identifier
intel_cht_int33fe:
- Convert to use SPDX identifier
intel_chtdc_ti_pwrbtn:
- Add SPDX identifier
intel_int0002_vgpio:
- Convert to use SPDX identifier
- Implement irq_set_wake
- Enable the driver on Bay Trail platforms
intel_menlow:
- Convert to use SPDX identifier
- Sort headers alphabetically
intel_mid_powerbtn:
- Convert to use SPDX identifier
- Remove unnecessary init.h inclusion
- Get rid of custom ICPU() macro
intel_mid_thermal:
- Convert to use SPDX identifier
- Sort headers alphabetically
intel_oaktrail:
- Convert to use SPDX identifier
- Sort headers alphabetically
intel_pmc:
- Convert to use SPDX identifier
- Sort headers alphabetically
intel_punit_ipc:
- Convert to use SPDX identifier
- Sort headers alphabetically
intel_scu_ipc:
- Convert to use SPDX identifier
- Sort headers alphabetically
intel_telemetry:
- Get rid of custom macro
- report debugfs failure
- Convert to use SPDX identifier
intel_turbo_max_3:
- Convert to use SPDX identifier
- Sort headers alphabetically
mlx-platform:
- Properly use mlxplat_mlxcpld_msn201x_items
touchscreen_dmi:
- Add min-x and min-y settings for various models
- Add info for the Onda V80 Plus v3 tablet
- Add info for the Trekstor Primetab T13B tablet
- Add info for the Trekstor Primebook C11 convertible
tracing:
- Trivia spelling fix containerof() -> container_of()
wmi:
- declare device_type structure as constant
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJb2mDCAAoJEKbMaAwKp364KdkH/Rar8cenw7uFeVzT5o4fGzTn
0Oo1Pnwh+hPgmQwmf8O/mHsa/1Zb9nX4nNLU/ysDUjAAZ9wZLoB57HlImQquPA74
c8lXTz5MVF140WB1f1Ck5PmeonJR2Xve7HTYCoBmGo71jOxHxCgJbp1Giiho0Imd
3NXzzahEnAiy/L5PhqqYTmIfTeAHQ2Fo7GkHCjMnS20FP2fBtvPrc7db03F+FZ4y
QTfbT0oR42NdeW21AbCRGY3P47axB3xDJX4LOYrb4uo4CIzd1yatlHk407NRRyv8
pab6aeJR23FouA/tcvv+T36D3vqRw78e6BWdoyowWOd7CUOgjtSC3lKGzfT6hSY=
=0BDZ
-----END PGP SIGNATURE-----
Merge tag 'platform-drivers-x86-v4.20-1' of git://git.infradead.org/linux-platform-drivers-x86
Pull x86 platform driver updates from Darren Hart:
- Move the Dell dcdbas and dell_rbu drivers into platform/drivers/x86
as they are closely coupled with other drivers in this location.
- Improve _init* usage for acerhdf and fix some usage issues with
messages and module parameters.
- Simplify asus-wmi by calling ACPI/WMI methods directly, eliminating
workqueue overhead, eliminate double reporting of keyboard backlight.
- Fix wake from USB failure on Bay Trail devices (intel_int0002_vgpio).
- Notify intel_telemetry users when IPC1 device is not enabled.
- Update various drivers with new laptop model IDs.
- Update several intel drivers to use SPDX identifers and order headers
alphabetically.
* tag 'platform-drivers-x86-v4.20-1' of git://git.infradead.org/linux-platform-drivers-x86: (64 commits)
HID: asus: only support backlight when it's not driven by WMI
platform/x86: asus-wmi: export function for evaluating WMI methods
platform/x86: asus-wmi: Only notify kbd LED hw_change by fn-key pressed
platform/x86: wmi: declare device_type structure as constant
platform/x86: ideapad: Add Y530-15ICH to no_hw_rfkill
platform/x86: Add Intel AtomISP2 dummy / power-management driver
platform/x86: touchscreen_dmi: Add min-x and min-y settings for various models
platform/x86: touchscreen_dmi: Add info for the Onda V80 Plus v3 tablet
platform/x86: touchscreen_dmi: Add info for the Trekstor Primetab T13B tablet
platform/x86: intel_telemetry: Get rid of custom macro
platform/x86: intel_telemetry: report debugfs failure
MAINTAINERS: intel_telemetry: Update maintainers info
platform/x86: Add LG Gram laptop special features driver
platform/x86: asus-wmi: Simplify the keyboard brightness updating process
platform/x86: touchscreen_dmi: Add info for the Trekstor Primebook C11 convertible
platform/x86: mlx-platform: Properly use mlxplat_mlxcpld_msn201x_items
MAINTAINERS: intel_pmc_core: Update MAINTAINERS
firmware: dcdbas: include linux/io.h
platform/x86: intel-wmi-thunderbolt: Add dynamic debugging
platform/x86: intel-wmi-thunderbolt: Convert to use SPDX identifier
...
The Asus GL502VSK has the same 0B05:1837 keyboard as we've seen in
several Republic of Gamers laptops.
However, in this model, the keybard backlight control exposed by hid-asus
has no effect on the keyboard backlight. Instead, the keyboard
backlight is correctly driven by asus-wmi.
With two keyboard backlight devices available (and only the acer-wmi
one working), GNOME is picking the wrong one to drive in the UI.
Avoid this problem by not creating the backlight interface when we
detect a WMI-driven keyboard backlight.
We have also tested Asus GL702VMK which does have the hid-asus
backlight present, and it still works fine with this patch (WMI method
call returns UNSUPPORTED_METHOD).
A direct "depends on ASUS_WMI" is intentionally avoided so that HID_ASUS
users who have ASUS_WMI=n will not quietly lose their HID_ASUS driver on
a kernel upgrade.
Signed-off-by: Daniel Drake <drake@endlessm.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
