New FIFO flow control feature was added in PPv23.
PPv2 FIFO polled by HW and trigger pause frame if FIFO
fill level is below threshold.
FIFO HW flow control enabled with CM3 RXQ&BM flow
control with ethtool.
Current FIFO thresholds is:
9KB for port with maximum speed 10Gb/s port
4KB for port with maximum speed 5Gb/s port
2KB for port with maximum speed 1Gb/s port
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Acked-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PP2v23 hardware supports a feature allowing to double the
size of BPPI by decreasing number of pools from 16 to 8.
Increasing of BPPI size protect BM drop from BPPI underrun.
Underrun could occurred due to stress on DDR and as result slow buffer
transition from BPPE to BPPI.
New BPPI threshold recommended by spec is:
BPPI low threshold - 640 buffers
BPPI high threshold - 832 buffers
Supported only in PPv23.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Acked-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add ethtool flow control configuration support.
Tx flow control retrieved correctly by ethtool get function.
FW per port ethtool configuration capability added.
Patch also takes care about mtu change procedure, if PPv2 switch
BM pools during mtu change.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Acked-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds RXQ flow control configurations.
Flow control disabled by default.
Minimum ring size limited to 1024 descriptors.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Acked-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables global flow control in FW and in the phylink validate mask.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Acked-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The firmware needs to monitor the RX Non-occupied descriptor
bits for flow control to move to XOFF mode.
These bits need to be unmasked to be functional, but they will
not raise interrupts as we leave the RX exception summary
bit in MVPP2_ISR_RX_TX_MASK_REG clear.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Acked-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Flow Control periodic timer would be used if port in
XOFF to transmit periodic XOFF frames.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Acked-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
BM pool and RXQ size increased to support Firmware Flow Control.
Minimum depletion thresholds to support FC are 1024 buffers.
BM pool size increased to 2048 to have some 1024 buffers
space between depletion thresholds and BM pool size.
Jumbo frames require a 9888B buffer, so memory requirements
for data buffers increased from 7MB to 24MB.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Acked-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add PPv23 version definition.
PPv23 is new packet processor in CP115.
Everything that supported by PPv22, also supported by PPv23.
No functional changes in this stage.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Acked-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we have PP2v1 and PP2v2 hw-versions, with some different
handlers depending upon condition hw_version = MVPP21/MVPP22.
In a future there will be also PP2v3. Let's use now the generic
"if equal/notEqual MVPP21" for all cases instead of "if MVPP22".
This patch does not change any functionality.
It is not intended to introduce PP2v3.
It just modifies MVPP21/MVPP22 check-condition
bringing it to generic and unified form correct for new-code
introducing and PP2v3 net-next generation.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Acked-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds CM3 memory map.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This entry used when skipping the parser needed,
for example, the custom header pretended to ethernet header.
Suggested-by: Liron Himi <liron@marvell.com>
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Last TCAM data contains TCAM enable bit.
It should be written after SRAM data before entry enabled.
Fixes: 3f518509de ("ethernet: Add new driver for Marvell Armada 375 network unit")
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Link: https://lore.kernel.org/r/1612172139-28343-1-git-send-email-stefanc@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Daniel Borkmann says:
====================
pull-request: bpf-next 2021-01-16
1) Extend atomic operations to the BPF instruction set along with x86-64 JIT support,
that is, atomic{,64}_{xchg,cmpxchg,fetch_{add,and,or,xor}}, from Brendan Jackman.
2) Add support for using kernel module global variables (__ksym externs in BPF
programs) retrieved via module's BTF, from Andrii Nakryiko.
3) Generalize BPF stackmap's buildid retrieval and add support to have buildid
stored in mmap2 event for perf, from Jiri Olsa.
4) Various fixes for cross-building BPF sefltests out-of-tree which then will
unblock wider automated testing on ARM hardware, from Jean-Philippe Brucker.
5) Allow to retrieve SOL_SOCKET opts from sock_addr progs, from Daniel Borkmann.
6) Clean up driver's XDP buffer init and split into two helpers to init per-
descriptor and non-changing fields during processing, from Lorenzo Bianconi.
7) Minor misc improvements to libbpf & bpftool, from Ian Rogers.
* https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (41 commits)
perf: Add build id data in mmap2 event
bpf: Add size arg to build_id_parse function
bpf: Move stack_map_get_build_id into lib
bpf: Document new atomic instructions
bpf: Add tests for new BPF atomic operations
bpf: Add bitwise atomic instructions
bpf: Pull out a macro for interpreting atomic ALU operations
bpf: Add instructions for atomic_[cmp]xchg
bpf: Add BPF_FETCH field / create atomic_fetch_add instruction
bpf: Move BPF_STX reserved field check into BPF_STX verifier code
bpf: Rename BPF_XADD and prepare to encode other atomics in .imm
bpf: x86: Factor out a lookup table for some ALU opcodes
bpf: x86: Factor out emission of REX byte
bpf: x86: Factor out emission of ModR/M for *(reg + off)
tools/bpftool: Add -Wall when building BPF programs
bpf, libbpf: Avoid unused function warning on bpf_tail_call_static
selftests/bpf: Install btf_dump test cases
selftests/bpf: Fix installation of urandom_read
selftests/bpf: Move generated test files to $(TEST_GEN_FILES)
selftests/bpf: Fix out-of-tree build
...
====================
Link: https://lore.kernel.org/r/20210116012922.17823-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Patch didn't fix any issue, just improve parse flow
and align ipv4 parse flow with ipv6 parse flow.
Currently ipv4 kenguru parser first check IP protocol(TCP/UDP)
and then destination IP address.
Patch introduce reverse ipv4 parse, first destination IP address parsed
and only then IP protocol.
This would allow extend capability for packet L4 parsing and align ipv4
parsing flow with ipv6.
Suggested-by: Liron Himi <liron@marvell.com>
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Link: https://lore.kernel.org/r/1610289059-14962-1-git-send-email-stefanc@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Packet Processor hardware not connected to MAC flow control unit and
cannot support TX flow control.
This patch disable flow control support.
Fixes: 3f518509de ("ethernet: Add new driver for Marvell Armada 375 network unit")
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Acked-by: Marcin Wojtas <mw@semihalf.com>
Link: https://lore.kernel.org/r/1610306582-16641-1-git-send-email-stefanc@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The packet coalescing interrupt threshold has separated registers
for different aggregated/cpu (sw-thread). The required value should
be loaded for every thread but not only for 1 current cpu.
Fixes: 213f428f50 ("net: mvpp2: add support for TX interrupts and RX queue distribution modes")
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Link: https://lore.kernel.org/r/1608748521-11033-1-git-send-email-stefanc@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
During GoP port 2 Networking Complex Control mode of operation configurations,
also GoP port 3 mode of operation was wrongly set.
Patch removes these configurations.
Fixes: f84bf386f3 ("net: mvpp2: initialize the GoP")
Acked-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Link: https://lore.kernel.org/r/1608462149-1702-1-git-send-email-stefanc@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Current PPPoE+IPv6 entry is jumping to 'next-hdr'
field and not to 'DIP' field as done for IPv4.
Fixes: 3f518509de ("ethernet: Add new driver for Marvell Armada 375 network unit")
Reported-by: Liron Himi <lironh@marvell.com>
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Link: https://lore.kernel.org/r/1608230266-22111-1-git-send-email-stefanc@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Issue:
Flow control frame used to pause GoP(MAC) was delivered to the CPU
and created a load on the CPU. Since XOFF/XON frames are used only
by MAC, these frames should be dropped inside MAC.
Fix:
According to 802.3-2012 - IEEE Standard for Ethernet pause frame
has unique destination MAC address 01-80-C2-00-00-01.
Add TCAM parser entry to track and drop pause frames by destination MAC.
Fixes: 3f518509de ("ethernet: Add new driver for Marvell Armada 375 network unit")
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Link: https://lore.kernel.org/r/1608229817-21951-1-git-send-email-stefanc@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Force link UP can be enabled by bootloader during tftpboot
and breaks NFS support.
Force link UP disabled during port init procedure.
Fixes: f84bf386f3 ("net: mvpp2: initialize the GoP")
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Acked-by: Marcin Wojtas <mw@semihalf.com>
Link: https://lore.kernel.org/r/1608216735-14501-1-git-send-email-stefanc@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Alexei Starovoitov says:
====================
pull-request: bpf-next 2020-12-03
The main changes are:
1) Support BTF in kernel modules, from Andrii.
2) Introduce preferred busy-polling, from Björn.
3) bpf_ima_inode_hash() and bpf_bprm_opts_set() helpers, from KP Singh.
4) Memcg-based memory accounting for bpf objects, from Roman.
5) Allow bpf_{s,g}etsockopt from cgroup bind{4,6} hooks, from Stanislav.
* https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (118 commits)
selftests/bpf: Fix invalid use of strncat in test_sockmap
libbpf: Use memcpy instead of strncpy to please GCC
selftests/bpf: Add fentry/fexit/fmod_ret selftest for kernel module
selftests/bpf: Add tp_btf CO-RE reloc test for modules
libbpf: Support attachment of BPF tracing programs to kernel modules
libbpf: Factor out low-level BPF program loading helper
bpf: Allow to specify kernel module BTFs when attaching BPF programs
bpf: Remove hard-coded btf_vmlinux assumption from BPF verifier
selftests/bpf: Add CO-RE relocs selftest relying on kernel module BTF
selftests/bpf: Add support for marking sub-tests as skipped
selftests/bpf: Add bpf_testmod kernel module for testing
libbpf: Add kernel module BTF support for CO-RE relocations
libbpf: Refactor CO-RE relocs to not assume a single BTF object
libbpf: Add internal helper to load BTF data by FD
bpf: Keep module's btf_data_size intact after load
bpf: Fix bpf_put_raw_tracepoint()'s use of __module_address()
selftests/bpf: Add Userspace tests for TCP_WINDOW_CLAMP
bpf: Adds support for setting window clamp
samples/bpf: Fix spelling mistake "recieving" -> "receiving"
bpf: Fix cold build of test_progs-no_alu32
...
====================
Link: https://lore.kernel.org/r/20201204021936.85653-1-alexei.starovoitov@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix to return negative error code -ENOENT from invalid configuration
error handling case instead of 0, as done elsewhere in this function.
Fixes: 4bb0432628 ("net: mvpp2: phylink support")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20201203141806.37966-1-wanghai38@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add napi_id to the xdp_rxq_info structure, and make sure the XDP
socket pick up the napi_id in the Rx path. The napi_id is used to find
the corresponding NAPI structure for socket busy polling.
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/bpf/20201130185205.196029-7-bjorn.topel@gmail.com
Tx/Rx FIFO is a HW resource limited by total size, but shared
by all ports of same CP110 and impacting port-performance.
Do not divide the FIFO for ports which are not enabled in DTS,
so active ports could have more FIFO.
No change in FIFO allocation if all 3 ports on the communication
processor enabled in DTS.
The active port mapping should be done in probe before FIFO-init.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/1606154073-28267-1-git-send-email-stefanc@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
rivers/net/ethernet/marvell/mvpp2/mvpp2_main.c:7084:36: warning: ‘mvpp2_acpi_match’ defined but not used [-Wunused-const-variable=]
7084 | static const struct acpi_device_id mvpp2_acpi_match[] = {
| ^~~~~~~~~~~~~~~~
Wrap the definition inside #ifdef/#endif.
Compile tested only.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Richard Cochran points out that SKBTX_IN_PROGRESS should be set when
the skbuff is queued for timestamping. Add this.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the functions mvpp2_isr_handle_xlg() and
mvpp2_isr_handle_gmac_internal(), the bool variable link is assigned a
true value in the case that a given bit of val is set. However, if the
bit is unset, no value is assigned to link and it is then passed to
mvpp2_isr_handle_link() without being initialised. Fix by assigning to
link the value of the bit test.
Build-tested on x86.
Fixes: 36cfd3a6e5 ("net: mvpp2: restructure "link status" interrupt handling")
Signed-off-by: Alex Dewar <alex.dewar90@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for timestamping transmit packets. We allocate SYNC
messages to queue 1, every other message to queue 0.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for receive timestamping. When enabled, the hardware adds
a timestamp into the receive queue descriptor for all received packets
with no filtering. Hence, we can only support NONE or ALL receive
filter modes.
The timestamp in the receive queue contains two bit sof seconds and
the full nanosecond timestamp. This has to be merged with the remainder
of the seconds from the TAI clock to arrive at a full timestamp before
we can convert it to a ktime for the skb hardware timestamp field.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the TAI block in the mvpp2.2 hardware.
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check the first level interrupt status registers to determine how to
further process the port interrupt. We will need this to know whether
to invoke the link status processing and/or the PTP processing for
both XLG and GMAC.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The link interrupt is used for way more than just the link status; it
comes from a collection of units to do with the port. The Marvell
documentation describes the interrupt as "GOP port X interrupt".
Since we are adding PTP support, and the PTP interrupt uses this,
rename it to be more inline with the documentation.
This interrupt is also mis-named in the DT binding, but we leave that
alone.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "link status" interrupt is used for more than just link status.
Restructure mvpp2_link_status_isr() so we can add additional handling.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
We got slightly different patches removing a double word
in a comment in net/ipv4/raw.c - picked the version from net.
Simple conflict in drivers/net/ethernet/ibm/ibmvnic.c. Use cached
values instead of VNIC login response buffer (following what
commit 507ebe6444 ("ibmvnic: Fix use-after-free of VNIC login
response buffer") did).
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Split the XLG and GMAC PCS implementations and switch between them
during the mac_prepare() method.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert mvpp2 to phylink's new pcs support.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the GMAC reset handling into mac_prepare() / mac_finish()
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ensure that the port is forced down while reconfiguring, controlling
this via mac_prepare() and mac_finish() so that it is down while we
are configuring our (future) PCS.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert mvpp2 to use the mac_prepare() and mac_finish() methods in
preparation to converting mvpp2 to split-PCS support.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tidy up the ACPI hack so that we can minimise the function prototypes
for this. This avoids adding further prototypes unnecessarily.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf-next 2020-08-04
The following pull-request contains BPF updates for your *net-next* tree.
We've added 73 non-merge commits during the last 9 day(s) which contain
a total of 135 files changed, 4603 insertions(+), 1013 deletions(-).
The main changes are:
1) Implement bpf_link support for XDP. Also add LINK_DETACH operation for the BPF
syscall allowing processes with BPF link FD to force-detach, from Andrii Nakryiko.
2) Add BPF iterator for map elements and to iterate all BPF programs for efficient
in-kernel inspection, from Yonghong Song and Alexei Starovoitov.
3) Separate bpf_get_{stack,stackid}() helpers for perf events in BPF to avoid
unwinder errors, from Song Liu.
4) Allow cgroup local storage map to be shared between programs on the same
cgroup. Also extend BPF selftests with coverage, from YiFei Zhu.
5) Add BPF exception tables to ARM64 JIT in order to be able to JIT BPF_PROBE_MEM
load instructions, from Jean-Philippe Brucker.
6) Follow-up fixes on BPF socket lookup in combination with reuseport group
handling. Also add related BPF selftests, from Jakub Sitnicki.
7) Allow to use socket storage in BPF_PROG_TYPE_CGROUP_SOCK-typed programs for
socket create/release as well as bind functions, from Stanislav Fomichev.
8) Fix an info leak in xsk_getsockopt() when retrieving XDP stats via old struct
xdp_statistics, from Peilin Ye.
9) Fix PT_REGS_RC{,_CORE}() macros in libbpf for MIPS arch, from Jerry Crunchtime.
10) Extend BPF kernel test infra with skb->family and skb->{local,remote}_ip{4,6}
fields and allow user space to specify skb->dev via ifindex, from Dmitry Yakunin.
11) Fix a bpftool segfault due to missing program type name and make it more robust
to prevent them in future gaps, from Quentin Monnet.
12) Consolidate cgroup helper functions across selftests and fix a v6 localhost
resolver issue, from John Fastabend.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
