When building with -Wincompatible-function-pointer-types-strict, a
warning designed to catch potential kCFI failures at build time rather
than run time due to incorrect function pointer types, there is a
warning due to a mismatch between the type of the mode parameter in
ptp_ocp_dpll_mode_get() vs. what the function pointer prototype for
->mode_get() in 'struct dpll_device_ops' expects.
drivers/ptp/ptp_ocp.c:4353:14: error: incompatible function pointer types initializing 'int (*)(const struct dpll_device *, void *, enum dpll_mode *, struct netlink_ext_ack *)' with an expression of type 'int (const struct dpll_device *, void *, u32 *, struct netlink_ext_ack *)' (aka 'int (const struct dpll_device *, void *, unsigned int *, struct netlink_ext_ack *)') [-Werror,-Wincompatible-function-pointer-types-strict]
4353 | .mode_get = ptp_ocp_dpll_mode_get,
| ^~~~~~~~~~~~~~~~~~~~~
1 error generated.
Change the type of the mode parameter in ptp_ocp_dpll_mode_get() to
clear up the warning and avoid kCFI failures at run time.
Fixes: 09eeb3aecc ("ptp_ocp: implement DPLL ops")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20231002-net-wifpts-dpll_mode_get-v1-1-a356a16413cf@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There is a copy and paste error so this uses a valid pointer instead of
an error pointer.
Fixes: 09eeb3aecc ("ptp_ocp: implement DPLL ops")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Link: https://lore.kernel.org/r/5c581336-0641-48bd-88f7-51984c3b1f79@moroto.mountain
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When device_add() fails, ptp_ocp_dev_release() will be called
after put_device(). Therefore, it seems that the
ptp_ocp_dev_release() before put_device() is redundant.
Fixes: 773bda9649 ("ptp: ocp: Expose various resources on the timecard.")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Reviewed-by: Vadim Feodrenko <vadim.fedorenko@linux.dev>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement basic DPLL operations in ptp_ocp driver as the
simplest example of using new subsystem.
Signed-off-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are several cases where virtual net devices may benefit from
having a PTP clock, and these have to do with testing. I can see at
least netdevsim and veth as potential users of a common mock-up PTP
hardware clock driver.
The proposed idea is to create an object which emulates PTP clock
operations on top of the unadjustable CLOCK_MONOTONIC_RAW plus a
software-controlled time domain via a timecounter/cyclecounter and then
link that PHC to the netdevsim device.
The driver is fully functional for its intended purpose, and it
successfully passes the PTP selftests.
$ cd tools/testing/selftests/ptp/
$ ./phc.sh /dev/ptp2
TEST: settime [ OK ]
TEST: adjtime [ OK ]
TEST: adjfreq [ OK ]
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20230807193324.4128292-7-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Link: https://lore.kernel.org/r/20230714174922.4063153-1-robh@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The .adjphase operation is an operation that is implemented only by certain
PHCs. The sysfs device attribute node for querying the maximum phase
adjustment supported should not be exposed on devices that do not support
.adjphase.
Fixes: c3b60ab7a4 ("ptp: Add .getmaxphase callback to ptp_clock_info")
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Reported-by: Nathan Chancellor <nathan@kernel.org>
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Reported-by: Linux Kernel Functional Testing <lkft@linaro.org>
Link: https://lore.kernel.org/netdev/20230627162146.GA114473@dev-arch.thelio-3990X/
Link: https://lore.kernel.org/all/CA+G9fYtKCZeAUTtwe69iK8Xcz1mOKQzwcy49wd+imZrfj6ifXA@mail.gmail.com/
Tested-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Petr Vorel <pvorel@suse.cz>
Message-ID: <20230627232139.213130-1-rrameshbabu@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add a function that advertises a maximum offset of zero supported by
ptp_clock_info .adjphase in the OCP null ptp implementation.
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Jonathan Lemon <jonathan.lemon@gmail.com>
Cc: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Acked-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Signed-off-by: David S. Miller <davem@davemloft.net>
Advertise the maximum offset the .adjphase callback is capable of
supporting in nanoseconds for IDT devices.
Refactor the negation of the offset stored in the register to be after the
boundary check of the offset value rather than before. Boundary check based
on the intended value rather than its device-specific representation.
Depend on ptp_clock_adjtime for handling out-of-range offsets.
ptp_clock_adjtime returns -ERANGE instead of clamping out-of-range offsets.
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Min Li <min.li.xe@renesas.com>
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Advertise the maximum offset the .adjphase callback is capable of
supporting in nanoseconds for IDT ClockMatrix devices. Depend on
ptp_clock_adjtime for handling out-of-range offsets. ptp_clock_adjtime
returns -ERANGE instead of clamping out-of-range offsets.
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Vincent Cheng <vincent.cheng.xh@renesas.com>
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enables advertisement of the maximum offset supported by the phase control
functionality of PHCs. The callback is used to return an error if an offset
not supported by the PHC is used in ADJ_OFFSET. The ioctls
PTP_CLOCK_GETCAPS and PTP_CLOCK_GETCAPS2 now advertise the maximum offset a
PHC's phase control functionality is capable of supporting. Introduce new
sysfs node, max_phase_adjustment.
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Maciek Machnikowski <maciek@machnikowski.net>
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MIPS Boston board, which is using MIPS_GENERIC kernel is using
EG20T PCH and thus need this driver.
Dependency of PCH_GBE, PTP_1588_CLOCK_PCH is also fixed for
MIPS_GENERIC.
Note that CONFIG_PCH_GBE is selected in arch/mips/configs/generic/
board-boston.config for a while, some how it's never wired up
in Kconfig.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230607055953.34110-1-jiaxun.yang@flygoat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Here is the large set of driver core changes for 6.4-rc1.
Once again, a busy development cycle, with lots of changes happening in
the driver core in the quest to be able to move "struct bus" and "struct
class" into read-only memory, a task now complete with these changes.
This will make the future rust interactions with the driver core more
"provably correct" as well as providing more obvious lifetime rules for
all busses and classes in the kernel.
The changes required for this did touch many individual classes and
busses as many callbacks were changed to take const * parameters
instead. All of these changes have been submitted to the various
subsystem maintainers, giving them plenty of time to review, and most of
them actually did so.
Other than those changes, included in here are a small set of other
things:
- kobject logging improvements
- cacheinfo improvements and updates
- obligatory fw_devlink updates and fixes
- documentation updates
- device property cleanups and const * changes
- firwmare loader dependency fixes.
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZEp7Sw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykitQCfamUHpxGcKOAGuLXMotXNakTEsxgAoIquENm5
LEGadNS38k5fs+73UaxV
=7K4B
-----END PGP SIGNATURE-----
Merge tag 'driver-core-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the large set of driver core changes for 6.4-rc1.
Once again, a busy development cycle, with lots of changes happening
in the driver core in the quest to be able to move "struct bus" and
"struct class" into read-only memory, a task now complete with these
changes.
This will make the future rust interactions with the driver core more
"provably correct" as well as providing more obvious lifetime rules
for all busses and classes in the kernel.
The changes required for this did touch many individual classes and
busses as many callbacks were changed to take const * parameters
instead. All of these changes have been submitted to the various
subsystem maintainers, giving them plenty of time to review, and most
of them actually did so.
Other than those changes, included in here are a small set of other
things:
- kobject logging improvements
- cacheinfo improvements and updates
- obligatory fw_devlink updates and fixes
- documentation updates
- device property cleanups and const * changes
- firwmare loader dependency fixes.
All of these have been in linux-next for a while with no reported
problems"
* tag 'driver-core-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (120 commits)
device property: make device_property functions take const device *
driver core: update comments in device_rename()
driver core: Don't require dynamic_debug for initcall_debug probe timing
firmware_loader: rework crypto dependencies
firmware_loader: Strip off \n from customized path
zram: fix up permission for the hot_add sysfs file
cacheinfo: Add use_arch[|_cache]_info field/function
arch_topology: Remove early cacheinfo error message if -ENOENT
cacheinfo: Check cache properties are present in DT
cacheinfo: Check sib_leaf in cache_leaves_are_shared()
cacheinfo: Allow early level detection when DT/ACPI info is missing/broken
cacheinfo: Add arm64 early level initializer implementation
cacheinfo: Add arch specific early level initializer
tty: make tty_class a static const structure
driver core: class: remove struct class_interface * from callbacks
driver core: class: mark the struct class in struct class_interface constant
driver core: class: make class_register() take a const *
driver core: class: mark class_release() as taking a const *
driver core: remove incorrect comment for device_create*
MIPS: vpe-cmp: remove module owner pointer from struct class usage.
...
We need the fixes in here for testing, as well as the driver core
changes for documentation updates to build on.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Conflicts:
drivers/net/ethernet/mediatek/mtk_ppe.c
3fbe4d8c0e ("net: ethernet: mtk_eth_soc: ppe: add support for flow accounting")
924531326e ("net: ethernet: mtk_eth_soc: add missing ppe cache flush when deleting a flow")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Adding a DFL (Device Feature List) device driver of ToD device for
Intel FPGA cards.
The Intel FPGA Time of Day(ToD) IP within the FPGA DFL bus is exposed
as PTP Hardware clock(PHC) device to the Linux PTP stack to synchronize
the system clock to its ToD information using phc2sys utility of the
Linux PTP stack. The DFL is a hardware List within FPGA, which defines
a linked list of feature headers within the device MMIO space to provide
an extensible way of adding subdevice features.
Signed-off-by: Raghavendra Khadatare <raghavendrax.anand.khadatare@intel.com>
Signed-off-by: Tianfei Zhang <tianfei.zhang@intel.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230328142455.481146-1-tianfei.zhang@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Smatch complains that:
drivers/ptp/ptp_qoriq.c ptp_qoriq_probe()
warn: 'base' from ioremap() not released.
Fix this by revising the parameter from 'ptp_qoriq->base' to 'base'.
This is only a bug if ptp_qoriq_init() returns on the
first -ENODEV error path.
For other error paths ptp_qoriq->base and base are the same.
And this change makes the code more readable.
Fixes: 7f4399ba40 ("ptp_qoriq: fix NULL access if ptp dt node missing")
Signed-off-by: SongJingyi <u201912584@hust.edu.cn>
Reviewed-by: Dan Carpenter <error27@gmail.com>
Reviewed-by: Dongliang Mu <dzm91@hust.edu.cn>
Link: https://lore.kernel.org/r/20230324031406.1895159-1-u201912584@hust.edu.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
KVM_HC_CLOCK_PAIRING currently fails inside SEV-SNP guests because the
guest passes an address to static data to the host. In confidential
computing the host can't access arbitrary guest memory so handling the
hypercall runs into an "rmpfault". To make the hypercall work, the guest
needs to explicitly mark the memory as decrypted. Do that in
kvm_arch_ptp_init(), but retain the previous behavior for
non-confidential guests to save us from having to allocate memory.
Add a new arch-specific function (kvm_arch_ptp_exit()) to free the
allocation and mark the memory as encrypted again.
Signed-off-by: Jeremi Piotrowski <jpiotrowski@linux.microsoft.com>
Link: https://lore.kernel.org/r/20230308150531.477741-1-jpiotrowski@linux.microsoft.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The module pointer in class_create() never actually did anything, and it
shouldn't have been requred to be set as a parameter even if it did
something. So just remove it and fix up all callers of the function in
the kernel tree at the same time.
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Link: https://lore.kernel.org/r/20230313181843.1207845-4-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to manually set the owner of a struct class, as the
registering function does it automatically, so remove all of the
explicit settings from various drivers that did so as it is unneeded.
This allows us to remove this pointer entirely from this structure going
forward.
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Link: https://lore.kernel.org/r/20230313181843.1207845-2-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it might not be relevant here). This
also fixes !CONFIG_OF error:
drivers/ptp/ptp_ines.c:783:34: error: ‘ines_ptp_ctrl_of_match’ defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Link: https://lore.kernel.org/r/20230312132637.352755-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Flashing firmware via devlink flash was failing on PTP OCP devices
because it is using Quad SPI mode, but the driver was not properly
behaving. With force_irq flag landed it now can be fixed.
Signed-off-by: Vadim Fedorenko <vadfed@meta.com>
Link: https://lore.kernel.org/r/20230309105421.2953451-1-vadfed@meta.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
vclocks were using spinlocks to protect access to its timecounter and
cyclecounter. Access to timecounter/cyclecounter is backed by the same
driver callbacks that are used for non-virtual PHCs, but the usage of
the spinlock imposes a new limitation that didn't exist previously: now
they're called in atomic context so they mustn't sleep.
Some drivers like sfc or ice may sleep on these callbacks, causing
errors like "BUG: scheduling while atomic: ptp5/25223/0x00000002"
Fix it replacing the vclock's spinlock by a mutex. It fix the mentioned
bug and it doesn't introduce longer delays.
I've tested synchronizing various different combinations of clocks:
- vclock->sysclock
- sysclock->vclock
- vclock->vclock
- hardware PHC in different NIC -> vclock
- created 4 vclocks and launch 4 parallel phc2sys processes with
lockdep enabled
In all cases, comparing the delays reported by phc2sys, they are in the
same range of values than before applying the patch.
Link: https://lore.kernel.org/netdev/69d0ff33-bd32-6aa5-d36c-fbdc3c01337c@redhat.com/
Fixes: 5d43f951b1 ("ptp: add ptp virtual clock driver framework")
Reported-by: Yalin Li <yalli@redhat.com>
Suggested-by: Richard Cochran <richardcochran@gmail.com>
Tested-by: Miroslav Lichvar <mlichvar@redhat.com>
Signed-off-by: Íñigo Huguet <ihuguet@redhat.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Link: https://lore.kernel.org/r/20230221130616.21837-1-ihuguet@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
1588 driver loses about 1us in adjtime operation at PTP slave
This is because adjtime operation uses a slow non-atomic tmr_cnt_read()
followed by tmr_cnt_write() operation.
In the above sequence, since the timer counter operation keeps
incrementing, it leads to latency. The tmr_offset register
(which is added to TMR_CNT_H/L register giving the current time)
must be programmed with the delta nanoseconds.
Signed-off-by: Nikhil Gupta <nikhil.gupta@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20230119204034.7969-1-nikhil.gupta@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Core
----
- Allow live renaming when an interface is up
- Add retpoline wrappers for tc, improving considerably the
performances of complex queue discipline configurations.
- Add inet drop monitor support.
- A few GRO performance improvements.
- Add infrastructure for atomic dev stats, addressing long standing
data races.
- De-duplicate common code between OVS and conntrack offloading
infrastructure.
- A bunch of UBSAN_BOUNDS/FORTIFY_SOURCE improvements.
- Netfilter: introduce packet parser for tunneled packets
- Replace IPVS timer-based estimators with kthreads to scale up
the workload with the number of available CPUs.
- Add the helper support for connection-tracking OVS offload.
BPF
---
- Support for user defined BPF objects: the use case is to allocate
own objects, build own object hierarchies and use the building
blocks to build own data structures flexibly, for example, linked
lists in BPF.
- Make cgroup local storage available to non-cgroup attached BPF
programs.
- Avoid unnecessary deadlock detection and failures wrt BPF task
storage helpers.
- A relevant bunch of BPF verifier fixes and improvements.
- Veristat tool improvements to support custom filtering, sorting,
and replay of results.
- Add LLVM disassembler as default library for dumping JITed code.
- Lots of new BPF documentation for various BPF maps.
- Add bpf_rcu_read_{,un}lock() support for sleepable programs.
- Add RCU grace period chaining to BPF to wait for the completion
of access from both sleepable and non-sleepable BPF programs.
- Add support storing struct task_struct objects as kptrs in maps.
- Improve helper UAPI by explicitly defining BPF_FUNC_xxx integer
values.
- Add libbpf *_opts API-variants for bpf_*_get_fd_by_id() functions.
Protocols
---------
- TCP: implement Protective Load Balancing across switch links.
- TCP: allow dynamically disabling TCP-MD5 static key, reverting
back to fast[er]-path.
- UDP: Introduce optional per-netns hash lookup table.
- IPv6: simplify and cleanup sockets disposal.
- Netlink: support different type policies for each generic
netlink operation.
- MPTCP: add MSG_FASTOPEN and FastOpen listener side support.
- MPTCP: add netlink notification support for listener sockets
events.
- SCTP: add VRF support, allowing sctp sockets binding to VRF
devices.
- Add bridging MAC Authentication Bypass (MAB) support.
- Extensions for Ethernet VPN bridging implementation to better
support multicast scenarios.
- More work for Wi-Fi 7 support, comprising conversion of all
the existing drivers to internal TX queue usage.
- IPSec: introduce a new offload type (packet offload) allowing
complete header processing and crypto offloading.
- IPSec: extended ack support for more descriptive XFRM error
reporting.
- RXRPC: increase SACK table size and move processing into a
per-local endpoint kernel thread, reducing considerably the
required locking.
- IEEE 802154: synchronous send frame and extended filtering
support, initial support for scanning available 15.4 networks.
- Tun: bump the link speed from 10Mbps to 10Gbps.
- Tun/VirtioNet: implement UDP segmentation offload support.
Driver API
----------
- PHY/SFP: improve power level switching between standard
level 1 and the higher power levels.
- New API for netdev <-> devlink_port linkage.
- PTP: convert existing drivers to new frequency adjustment
implementation.
- DSA: add support for rx offloading.
- Autoload DSA tagging driver when dynamically changing protocol.
- Add new PCP and APPTRUST attributes to Data Center Bridging.
- Add configuration support for 800Gbps link speed.
- Add devlink port function attribute to enable/disable RoCE and
migratable.
- Extend devlink-rate to support strict prioriry and weighted fair
queuing.
- Add devlink support to directly reading from region memory.
- New device tree helper to fetch MAC address from nvmem.
- New big TCP helper to simplify temporary header stripping.
New hardware / drivers
----------------------
- Ethernet:
- Marvel Octeon CNF95N and CN10KB Ethernet Switches.
- Marvel Prestera AC5X Ethernet Switch.
- WangXun 10 Gigabit NIC.
- Motorcomm yt8521 Gigabit Ethernet.
- Microchip ksz9563 Gigabit Ethernet Switch.
- Microsoft Azure Network Adapter.
- Linux Automation 10Base-T1L adapter.
- PHY:
- Aquantia AQR112 and AQR412.
- Motorcomm YT8531S.
- PTP:
- Orolia ART-CARD.
- WiFi:
- MediaTek Wi-Fi 7 (802.11be) devices.
- RealTek rtw8821cu, rtw8822bu, rtw8822cu and rtw8723du USB
devices.
- Bluetooth:
- Broadcom BCM4377/4378/4387 Bluetooth chipsets.
- Realtek RTL8852BE and RTL8723DS.
- Cypress.CYW4373A0 WiFi + Bluetooth combo device.
Drivers
-------
- CAN:
- gs_usb: bus error reporting support.
- kvaser_usb: listen only and bus error reporting support.
- Ethernet NICs:
- Intel (100G):
- extend action skbedit to RX queue mapping.
- implement devlink-rate support.
- support direct read from memory.
- nVidia/Mellanox (mlx5):
- SW steering improvements, increasing rules update rate.
- Support for enhanced events compression.
- extend H/W offload packet manipulation capabilities.
- implement IPSec packet offload mode.
- nVidia/Mellanox (mlx4):
- better big TCP support.
- Netronome Ethernet NICs (nfp):
- IPsec offload support.
- add support for multicast filter.
- Broadcom:
- RSS and PTP support improvements.
- AMD/SolarFlare:
- netlink extened ack improvements.
- add basic flower matches to offload, and related stats.
- Virtual NICs:
- ibmvnic: introduce affinity hint support.
- small / embedded:
- FreeScale fec: add initial XDP support.
- Marvel mv643xx_eth: support MII/GMII/RGMII modes for Kirkwood.
- TI am65-cpsw: add suspend/resume support.
- Mediatek MT7986: add RX wireless wthernet dispatch support.
- Realtek 8169: enable GRO software interrupt coalescing per
default.
- Ethernet high-speed switches:
- Microchip (sparx5):
- add support for Sparx5 TC/flower H/W offload via VCAP.
- Mellanox mlxsw:
- add 802.1X and MAC Authentication Bypass offload support.
- add ip6gre support.
- Embedded Ethernet switches:
- Mediatek (mtk_eth_soc):
- improve PCS implementation, add DSA untag support.
- enable flow offload support.
- Renesas:
- add rswitch R-Car Gen4 gPTP support.
- Microchip (lan966x):
- add full XDP support.
- add TC H/W offload via VCAP.
- enable PTP on bridge interfaces.
- Microchip (ksz8):
- add MTU support for KSZ8 series.
- Qualcomm 802.11ax WiFi (ath11k):
- support configuring channel dwell time during scan.
- MediaTek WiFi (mt76):
- enable Wireless Ethernet Dispatch (WED) offload support.
- add ack signal support.
- enable coredump support.
- remain_on_channel support.
- Intel WiFi (iwlwifi):
- enable Wi-Fi 7 Extremely High Throughput (EHT) PHY capabilities.
- 320 MHz channels support.
- RealTek WiFi (rtw89):
- new dynamic header firmware format support.
- wake-over-WLAN support.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
-----BEGIN PGP SIGNATURE-----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=CbJC
-----END PGP SIGNATURE-----
Merge tag 'net-next-6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Paolo Abeni:
"Core:
- Allow live renaming when an interface is up
- Add retpoline wrappers for tc, improving considerably the
performances of complex queue discipline configurations
- Add inet drop monitor support
- A few GRO performance improvements
- Add infrastructure for atomic dev stats, addressing long standing
data races
- De-duplicate common code between OVS and conntrack offloading
infrastructure
- A bunch of UBSAN_BOUNDS/FORTIFY_SOURCE improvements
- Netfilter: introduce packet parser for tunneled packets
- Replace IPVS timer-based estimators with kthreads to scale up the
workload with the number of available CPUs
- Add the helper support for connection-tracking OVS offload
BPF:
- Support for user defined BPF objects: the use case is to allocate
own objects, build own object hierarchies and use the building
blocks to build own data structures flexibly, for example, linked
lists in BPF
- Make cgroup local storage available to non-cgroup attached BPF
programs
- Avoid unnecessary deadlock detection and failures wrt BPF task
storage helpers
- A relevant bunch of BPF verifier fixes and improvements
- Veristat tool improvements to support custom filtering, sorting,
and replay of results
- Add LLVM disassembler as default library for dumping JITed code
- Lots of new BPF documentation for various BPF maps
- Add bpf_rcu_read_{,un}lock() support for sleepable programs
- Add RCU grace period chaining to BPF to wait for the completion of
access from both sleepable and non-sleepable BPF programs
- Add support storing struct task_struct objects as kptrs in maps
- Improve helper UAPI by explicitly defining BPF_FUNC_xxx integer
values
- Add libbpf *_opts API-variants for bpf_*_get_fd_by_id() functions
Protocols:
- TCP: implement Protective Load Balancing across switch links
- TCP: allow dynamically disabling TCP-MD5 static key, reverting back
to fast[er]-path
- UDP: Introduce optional per-netns hash lookup table
- IPv6: simplify and cleanup sockets disposal
- Netlink: support different type policies for each generic netlink
operation
- MPTCP: add MSG_FASTOPEN and FastOpen listener side support
- MPTCP: add netlink notification support for listener sockets events
- SCTP: add VRF support, allowing sctp sockets binding to VRF devices
- Add bridging MAC Authentication Bypass (MAB) support
- Extensions for Ethernet VPN bridging implementation to better
support multicast scenarios
- More work for Wi-Fi 7 support, comprising conversion of all the
existing drivers to internal TX queue usage
- IPSec: introduce a new offload type (packet offload) allowing
complete header processing and crypto offloading
- IPSec: extended ack support for more descriptive XFRM error
reporting
- RXRPC: increase SACK table size and move processing into a
per-local endpoint kernel thread, reducing considerably the
required locking
- IEEE 802154: synchronous send frame and extended filtering support,
initial support for scanning available 15.4 networks
- Tun: bump the link speed from 10Mbps to 10Gbps
- Tun/VirtioNet: implement UDP segmentation offload support
Driver API:
- PHY/SFP: improve power level switching between standard level 1 and
the higher power levels
- New API for netdev <-> devlink_port linkage
- PTP: convert existing drivers to new frequency adjustment
implementation
- DSA: add support for rx offloading
- Autoload DSA tagging driver when dynamically changing protocol
- Add new PCP and APPTRUST attributes to Data Center Bridging
- Add configuration support for 800Gbps link speed
- Add devlink port function attribute to enable/disable RoCE and
migratable
- Extend devlink-rate to support strict prioriry and weighted fair
queuing
- Add devlink support to directly reading from region memory
- New device tree helper to fetch MAC address from nvmem
- New big TCP helper to simplify temporary header stripping
New hardware / drivers:
- Ethernet:
- Marvel Octeon CNF95N and CN10KB Ethernet Switches
- Marvel Prestera AC5X Ethernet Switch
- WangXun 10 Gigabit NIC
- Motorcomm yt8521 Gigabit Ethernet
- Microchip ksz9563 Gigabit Ethernet Switch
- Microsoft Azure Network Adapter
- Linux Automation 10Base-T1L adapter
- PHY:
- Aquantia AQR112 and AQR412
- Motorcomm YT8531S
- PTP:
- Orolia ART-CARD
- WiFi:
- MediaTek Wi-Fi 7 (802.11be) devices
- RealTek rtw8821cu, rtw8822bu, rtw8822cu and rtw8723du USB
devices
- Bluetooth:
- Broadcom BCM4377/4378/4387 Bluetooth chipsets
- Realtek RTL8852BE and RTL8723DS
- Cypress.CYW4373A0 WiFi + Bluetooth combo device
Drivers:
- CAN:
- gs_usb: bus error reporting support
- kvaser_usb: listen only and bus error reporting support
- Ethernet NICs:
- Intel (100G):
- extend action skbedit to RX queue mapping
- implement devlink-rate support
- support direct read from memory
- nVidia/Mellanox (mlx5):
- SW steering improvements, increasing rules update rate
- Support for enhanced events compression
- extend H/W offload packet manipulation capabilities
- implement IPSec packet offload mode
- nVidia/Mellanox (mlx4):
- better big TCP support
- Netronome Ethernet NICs (nfp):
- IPsec offload support
- add support for multicast filter
- Broadcom:
- RSS and PTP support improvements
- AMD/SolarFlare:
- netlink extened ack improvements
- add basic flower matches to offload, and related stats
- Virtual NICs:
- ibmvnic: introduce affinity hint support
- small / embedded:
- FreeScale fec: add initial XDP support
- Marvel mv643xx_eth: support MII/GMII/RGMII modes for Kirkwood
- TI am65-cpsw: add suspend/resume support
- Mediatek MT7986: add RX wireless wthernet dispatch support
- Realtek 8169: enable GRO software interrupt coalescing per
default
- Ethernet high-speed switches:
- Microchip (sparx5):
- add support for Sparx5 TC/flower H/W offload via VCAP
- Mellanox mlxsw:
- add 802.1X and MAC Authentication Bypass offload support
- add ip6gre support
- Embedded Ethernet switches:
- Mediatek (mtk_eth_soc):
- improve PCS implementation, add DSA untag support
- enable flow offload support
- Renesas:
- add rswitch R-Car Gen4 gPTP support
- Microchip (lan966x):
- add full XDP support
- add TC H/W offload via VCAP
- enable PTP on bridge interfaces
- Microchip (ksz8):
- add MTU support for KSZ8 series
- Qualcomm 802.11ax WiFi (ath11k):
- support configuring channel dwell time during scan
- MediaTek WiFi (mt76):
- enable Wireless Ethernet Dispatch (WED) offload support
- add ack signal support
- enable coredump support
- remain_on_channel support
- Intel WiFi (iwlwifi):
- enable Wi-Fi 7 Extremely High Throughput (EHT) PHY capabilities
- 320 MHz channels support
- RealTek WiFi (rtw89):
- new dynamic header firmware format support
- wake-over-WLAN support"
* tag 'net-next-6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2002 commits)
ipvs: fix type warning in do_div() on 32 bit
net: lan966x: Remove a useless test in lan966x_ptp_add_trap()
net: ipa: add IPA v4.7 support
dt-bindings: net: qcom,ipa: Add SM6350 compatible
bnxt: Use generic HBH removal helper in tx path
IPv6/GRO: generic helper to remove temporary HBH/jumbo header in driver
selftests: forwarding: Add bridge MDB test
selftests: forwarding: Rename bridge_mdb test
bridge: mcast: Support replacement of MDB port group entries
bridge: mcast: Allow user space to specify MDB entry routing protocol
bridge: mcast: Allow user space to add (*, G) with a source list and filter mode
bridge: mcast: Add support for (*, G) with a source list and filter mode
bridge: mcast: Avoid arming group timer when (S, G) corresponds to a source
bridge: mcast: Add a flag for user installed source entries
bridge: mcast: Expose __br_multicast_del_group_src()
bridge: mcast: Expose br_multicast_new_group_src()
bridge: mcast: Add a centralized error path
bridge: mcast: Place netlink policy before validation functions
bridge: mcast: Split (*, G) and (S, G) addition into different functions
bridge: mcast: Do not derive entry type from its filter mode
...
The driver name is available in device_driver::name. Right now,
drivers still have to report this piece of information themselves in
their devlink_ops::info_get callback function.
In order to factorize code, make devlink_nl_info_fill() add the driver
name attribute.
Now that the core sets the driver name attribute, drivers are not
supposed to call devlink_info_driver_name_put() anymore. Remove
devlink_info_driver_name_put() and clean-up all the drivers using this
function in their callback.
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Tested-by: Ido Schimmel <idosch@nvidia.com> # mlxsw
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
PEROUT_ENABLE_OUTPUT_MASK was there to allow us to enable/disable
all the perout pins. But it is not standard procedure, we will
have to discard it.
Signed-off-by: Min Li <min.li.xe@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
82P33 family of chips can trigger TOD read/write by external
signal from one of the IN12/13/14 pins, which are set user
space programs by calling PTP_PIN_SETFUNC through ptp_ioctl
Signed-off-by: Min Li <min.li.xe@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For bus-based driver, device removal is implemented as:
1 device_remove()->
2 bus->remove()->
3 driver->remove()
Driver core needs no inform from callee(bus driver) about the
result of remove callback. In that case, commit fc7a6209d5
("bus: Make remove callback return void") forces bus_type::remove
be void-returned.
Now we have the situation that both 1 & 2 of calling chain are
void-returned, so it does not make much sense for 3(driver->remove)
to return non-void to its caller.
So the basic idea behind this change is making remove() callback of
any bus-based driver to be void-returned.
This change, for itself, is for device drivers based on acpi-bus.
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Lee Jones <lee@kernel.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dawei Li <set_pte_at@outlook.com>
Reviewed-by: Maximilian Luz <luzmaximilian@gmail.com> # for drivers/platform/surface/*
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Now that all drivers have been converted to .adjfine, we can remove the
.adjfreq from the interface structure.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert all remaining drivers that still use .adjfreq to the newer .adjfine
implementation. These drivers are not straightforward, as they use
non-standard methods of programming their hardware. They are all converted
to use scaled_ppm_to_ppb to get the parts per billion value that their
logic depends on.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Cc: Ariel Elior <aelior@marvell.com>
Cc: Sudarsana Kalluru <skalluru@marvell.com>
Cc: Manish Chopra <manishc@marvell.com>
Cc: Derek Chickles <dchickles@marvell.com>
Cc: Satanand Burla <sburla@marvell.com>
Cc: Felix Manlunas <fmanlunas@marvell.com>
Cc: Raju Rangoju <rajur@chelsio.com>
Cc: Joakim Zhang <qiangqing.zhang@nxp.com>
Cc: Edward Cree <ecree.xilinx@gmail.com>
Cc: Martin Habets <habetsm.xilinx@gmail.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ptp_phc implementation of .adjfreq is implemented in terms of a
straight forward "base * ppb / 1 billion" calculation.
Convert this to the newer .adjfine, updating the driver to use the recently
introduced adjust_by_scaled_ppm helper function.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A few PTP drivers implement a .adjfreq handler which indicates the
operation is not supported. Convert all of these to .adjfine.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: Wei Liu <wei.liu@kernel.org>
Cc: Dexuan Cui <decui@microsoft.com>
Cc: Vivek Thampi <vithampi@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously there was a fallback mode to flash firmware image without
proper header. But now we have different supported vendors and flashing
wrong image could destroy the hardware. Remove fallback mode and force
header check. Both vendors have published firmware images with headers.
Acked-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: Vadim Fedorenko <vadfed@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Orolia card has disciplining configuration and temperature table
stored in EEPROM. This patch exposes them as binary attributes to
have read and write access.
Acked-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Co-developed-by: Charles Parent <charles.parent@orolia2s.com>
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: Vadim Fedorenko <vadfed@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ART card provides interface to access to serial port of miniature atomic
clock found on the card. Add support for this device and configure it
during init phase.
Acked-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Co-developed-by: Charles Parent <charles.parent@orolia2s.com>
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: Vadim Fedorenko <vadfed@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This brings in the Orolia timecard support from the GitHub repository.
The card uses different drivers to provide access to i2c EEPROM and
firmware SPI flash. And it also has a bit different EEPROM map, but
other parts of the code are the same and could be reused.
Co-developed-by: Charles Parent <charles.parent@orolia2s.com>
Acked-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: Vadim Fedorenko <vadfed@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce structure to hold serial port line number and the baud rate
it supports.
Acked-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: Vadim Fedorenko <vadfed@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use ida_alloc_xxx()/ida_free() instead of
ida_simple_get()/ida_simple_remove().
The latter is deprecated and more verbose.
Signed-off-by: Bo Liu <liubo03@inspur.com>
Link: https://lore.kernel.org/r/20220926012744.3363-1-liubo03@inspur.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We have already a helper to get the first child device, use it and
drop custom approach.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Vadim Fedorenko <vadfed@fb.com>
Link: https://lore.kernel.org/r/20220921141005.2443-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Here is the set of SPDX comment updates for 6.0-rc1.
Nothing huge here, just a number of updated SPDX license tags and
cleanups based on the review of a number of common patterns in GPLv2
boilerplate text. Also included in here are a few other minor updates,
2 USB files, and one Documentation file update to get the SPDX lines
correct.
All of these have been in the linux-next tree for a very long time.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYupz3g8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynPUgCgslaf2ssCgW5IeuXbhla+ZBRAzisAnjVgOvLN
4AKdqbiBNlFbCroQwmeQ
=v1sg
-----END PGP SIGNATURE-----
Merge tag 'spdx-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx
Pull SPDX updates from Greg KH:
"Here is the set of SPDX comment updates for 6.0-rc1.
Nothing huge here, just a number of updated SPDX license tags and
cleanups based on the review of a number of common patterns in GPLv2
boilerplate text.
Also included in here are a few other minor updates, two USB files,
and one Documentation file update to get the SPDX lines correct.
All of these have been in the linux-next tree for a very long time"
* tag 'spdx-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx: (28 commits)
Documentation: samsung-s3c24xx: Add blank line after SPDX directive
x86/crypto: Remove stray comment terminator
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_406.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_398.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_391.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_390.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_385.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_320.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_319.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_318.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_298.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_292.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_179.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_168.RULE (part 2)
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_168.RULE (part 1)
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_160.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_152.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_149.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_147.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_133.RULE
...
The crc16() function is used to check the firmware validity, but
the library was not explicitly selected.
Fixes: 3c3673bde5 ("ptp: ocp: Add firmware header checks")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Acked-by: Vadim Fedorenko <vadfed@fb.com>
Link: https://lore.kernel.org/r/20220726220604.1339972-1-jonathan.lemon@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
While here it may be no difference, the kcalloc() has some checks
against overflow and it's logically correct to call it for an array.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Vadim Fedorenko <vfedorenko@novek.ru>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Cleaning up driver data is actually already handled by driver core,
so there is no need to do it manually.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Vadim Fedorenko <vfedorenko@novek.ru>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since platform_device_unregister() is NULL-aware, we don't need to duplicate
this check. Remove it and fold the rest of the code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Vadim Fedorenko <vfedorenko@novek.ru>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently we are using BIT(), but GENMASK(). Make use of the latter one
as well (far less error-prone, far more concise).
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Vadim Fedorenko <vfedorenko@novek.ru>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Based on the normalized pattern:
this program is free software you can redistribute it and/or modify it
under the terms of the gnu general public license as published by the
free software foundation version 2 this program is distributed as is
without any warranty of any kind whether express or implied without
even the implied warranty of merchantability or fitness for a
particular purpose see the gnu general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference.
Reviewed-by: Allison Randal <allison@lohutok.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Right now it's possible to flash any kind of binary via devlink and
break the card easily. This diff adds an optional header check when
installing the firmware.
Signed-off-by: Vadim Fedorenko <vadfed@fb.com>
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The NTL timecard design has a PPS1 selector which selects the
the PPS source automatically, according to Section 1.9 of the
documentation.
If there is a SMA PPS input detected:
- send signal to MAC and PPS slave selector.
If there is a MAC PPS input detected:
- send GNSS1 to the MAC
- send MAC to the PPS slave
If there is a GNSS1 input detected:
- send GNSS1 to the MAC
- send GNSS1 to the PPS slave.MAC
Change the debugfs summary so it reflects the correct mapping,
for assistance in debugging. No functional change.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Create an .init function for the op vector, and a corresponding
wrapper function, for different sma mapping setups.
Add a default_fcn to the sma information, and use it when displaying
information for pins which have fixed functions.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Move the SMA get and set functions into an operations vector for
different boards.
Create wrappers for the accessor functions.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The ocp selectors are all constant, so label them as such.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Group the sma input/output tables together and select the correct
group from the bp information. This allows adding new groups with
different sma mappings.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Preparse the firmware image information into loader/tag/version,
and set the fw capabilities based on the tag/version.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Celestica is producing card with their own vendor id and device id.
Add these ids to driver to support this card.
Signed-off-by: Vadim Fedorenko <vadfed@fb.com>
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
These #ifdefs are not required, so remove them.
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use 'resource_size_t' instead of 'unsigned long' when computing the
pci start address, for the benefit of 32-bit platforms.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In the detach path, the driver calls sysfs_remove_group() for the
groups it believes has been registered. However, if the group was
never previously registered, then this causes a splat.
Instead, compute the groups that should be registered in advance,
and then call sysfs_create_groups(), which registers them all at once.
Update the error handling appropriately.
Fixes: c205d53c49 ("ptp: ocp: Add firmware capability bits for feature gating")
Reported-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Link: https://lore.kernel.org/r/20220517214600.10606-1-jonathan.lemon@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use TOD_READ_SECONDARY for extts to keep TOD_READ_PRIMARY
for gettime and settime exclusively. Before this change,
TOD_READ_PRIMARY was used for both extts and gettime/settime,
which would result in changing TOD read/write triggers between
operations. Using TOD_READ_SECONDARY would make extts
independent of gettime/settime operation
Signed-off-by: Min Li <min.li.xe@renesas.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Link: https://lore.kernel.org/r/1652712427-14703-1-git-send-email-min.li.xe@renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
delta_ns is a s64, but it was being passed ptp_ocp_adjtime_coarse
as an u64. Also, it turns out that timespec64_add_ns() only handles
positive values, so perform the math with set_normalized_timespec().
Fixes: 90f8f4c0e3 ("ptp: ocp: Add ptp_ocp_adjtime_coarse for large adjustments")
Suggested-by: Vadim Fedorenko <vfedorenko@novek.ru>
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Acked-by: Vadim Fedorenko <vfedorenko@novek.ru>
Link: https://lore.kernel.org/r/20220513225231.1412-1-jonathan.lemon@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ptp_convert_timestamp() is called in the RX path of network messages.
The current implementation takes ~5000ns on 1.2GHz A53. This is too much
for the hot path of packet processing.
Introduce hash table for fast vclock lookup in ptp_convert_timestamp().
The execution time of ptp_convert_timestamp() is reduced to ~700ns on
1.2GHz A53.
Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
ptp_convert_timestamp() converts only the timestamp hwtstamp, which is
a field of the argument with the type struct skb_shared_hwtstamps *. So
a pointer to the hwtstamp field of this structure is sufficient.
Rework ptp_convert_timestamp() to use an argument of type ktime_t *.
This allows to add additional timestamp manipulation stages before the
call of ptp_convert_timestamp().
Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
ptp vclocks require a free running time for their timecounter.
Currently only a physical clock forced to free running is supported.
If vclocks are used, then the physical clock cannot be synchronized
anymore. The synchronized time is not available in hardware in this
case. As a result, timed transmission with TAPRIO hardware support
is not possible anymore.
If hardware would support a free running time additionally to the
physical clock, then the physical clock does not need to be forced to
free running. Thus, the physical clocks can still be synchronized
while vclocks are in use.
The physical clock could be used to synchronize the time domain of the
TSN network and trigger TAPRIO. In parallel vclocks can be used to
synchronize other time domains.
Introduce support for a free running cycle counter called cycles to
physical clocks. Rework ptp vclocks to use this free running cycle
counter. Default implementation is based on time of physical clock.
Thus, behavior of ptp vclocks based on physical clocks without free
running cycle counter is identical to previous behavior.
Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The initial code used roundup() to round the starting time to
a multiple of a period. This generated an error on 32-bit
systems, so was replaced with DIV_ROUND_UP_ULL().
However, this truncates to 32-bits on a 64-bit system. Replace
with DIV64_U64_ROUND_UP() instead.
Fixes: b325af3cfa ("ptp: ocp: Add signal generators and update sysfs nodes")
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Link: https://lore.kernel.org/r/20220506223739.1930-2-jonathan.lemon@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
nvmem_device_find returns a valid pointer or IS_ERR().
Handle this properly.
Fixes: 0cfcdd1ebc ("ptp: ocp: add nvmem interface for accessing eeprom")
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Link: https://lore.kernel.org/r/20220329160354.4035-1-jonathan.lemon@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This code is fine, but it's easier to review if we use snprintf()
instead of sprintf().
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Link: https://lore.kernel.org/r/20220318074723.GA6617@kili
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
An earlier patch mistakenly changed these variables from u32 to u16,
leading to unintended truncation. Restore the original logic.
Fixes: a509a7c61e ("ptp: ocp: Add support for selectable SMA directions.")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Link: https://lore.kernel.org/r/20220316165347.599154-1-jonathan.lemon@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The timecard now has 4 general purpose timestampers.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Input signals can be steered to any of the frequency counters.
The counter measures the frequency over a number of seconds:
echo 0 > freq1/seconds = turns off measurement
echo 1 > freq1/seconds = sets period & turns on measurment.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The signal generators can be programmed either via the sysfs
file or through a PTP_CLK_REQ_PEROUT ioctl request.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Newer firmware provides 4 programmable signal generators, add
support for those here. The signal generators provide the
ability to set the period, duty cycle, phase offset, and polarity,
with new values defaulting to prior values.
The period and phase offset are specified in nanoseconds.
E.g: period [duty [phase [polarity]]]
echo 500000000 > signal # 1/2 second period
echo 1000000 40 100 > signal # 1ms period, 40% on, offset 100ns
echo 0 > signal # turn off generator
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the ability to group sysfs nodes behind a firmware feature
check. This way non-present sysfs attributes are omitted on
older firmware, which does not have newer features.
This will be used in the upcoming patches which adds more
features to the timecard.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As there are may be 2 GNSS outputs, rename the first one for clarity.
This also works around a parsing issue when specifying selectors.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for the "IN: None" selector, which disables
the input on a sma pin. This should be compatible with old firmware
(the firmware will ignore it if not supported).
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Assuming the firmware allows it, the direction of each SMA connector
is no longer fixed. Handle remapping directions for each pin.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The serial port driver attempts to test for correct THRE behavior
on startup. However, it does this by disabling interrupts, and
then intentionally trying to trigger an interrupt in order to see
if the IIR bit is set in the UART.
However, in this FPGA design, the UART interrupt is generated
through the MSI vector, so when interrupts are re-enabled after
the test, the DMAR-IR reports an unhandled IRTE entry, since
no irq handler is installed at this point - it is installed
after the test.
This only happens on the /second/ open of the UART, since on the
first open, the x86_vector has installed and activated by the
driver probe, and is correctly handled. When the serial port is
closed for the first time, this vector is deactivated and removed,
leading to this error.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Link: https://lore.kernel.org/r/20220309223427.34745-1-jonathan.lemon@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
rsmu (Renesas Synchronization Management Unit ) driver is located in
drivers/mfd and responsible for creating multiple devices including
idt82p33 phc, which will then use the exposed regmap and mutex
handle to access i2c/spi bus.
Signed-off-by: Min Li <min.li.xe@renesas.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Link: https://lore.kernel.org/r/1646748651-16811-1-git-send-email-min.li.xe@renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Cache the firmware version when the card is initialized,
and use this field to populate the devlink firmware information.
The cached firmware version will be used for feature gating in
upcoming patches.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the at24 drivers for the eeprom, and use the accessors
via the nvmem API instead of direct i2c accesses. This makes
things cleaner.
Add an eeprom map table which specifies where the pre-defined
information is located. Retrieve the information and and export
it via the devlink interface.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When devlink_register() was removed from the error path, the
corresponding label was not updated. Rename the label for
readability puposes, no functional change.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Link: https://lore.kernel.org/r/20220308000458.2166-1-jonathan.lemon@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The > ARRAY_SIZE() needs to be >= ARRAY_SIZE() to prevent an out of
bounds access.
Fixes: 9f492c4cb2 ("ptp: ocp: add TOD debug information")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Link: https://lore.kernel.org/r/20220307141318.GA18867@kili
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
utc_tai_offset is used to correct IRIG, DCF and NMEA outputs and is
set during initialisation but is not corrected during leap second
announce event. Add watchdog code to control this correction.
Signed-off-by: Vadim Fedorenko <vadfed@fb.com>
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TOD correction register is used to compensate for leap seconds in
different domains. Export it as an attribute with write access.
Signed-off-by: Vadim Fedorenko <vadfed@fb.com>
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Monitoring of clock variance could be done through checking
the offset and the drift updates that are applied to atomic
clocks. Expose these values as attributes for the timecard.
Signed-off-by: Vadim Fedorenko <vadfed@fb.com>
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TOD information is currently displayed only on module load,
which doesn't provide updated information as the system runs.
Create a debug file which provides the current TOD status information,
and move the information display there.
Signed-off-by: Vadim Fedorenko <vadfed@fb.com>
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ("ptp: ocp: Have FPGA fold in ns adjustment for adjtime."), the
ns adjustment was written to the FPGA register, so the clock could
accurately perform adjustments.
However, the adjtime() call passes in a s64, while the clock adjustment
registers use a s32. When trying to perform adjustments with a large
value (37 sec), things fail.
Examine the incoming delta, and if larger than 1 sec, use the original
(coarse) adjustment method. If smaller than 1 sec, then allow the
FPGA to fold in the changes over a 1 second window.
Fixes: 6d59d4fa17 ("ptp: ocp: Have FPGA fold in ns adjustment for adjtime.")
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Link: https://lore.kernel.org/r/20220228203957.367371-1-jonathan.lemon@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The default values for hooks in the driver.pm are NULLs.
Hence drop unused pch_pm_ops.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220207210730.75252-6-andriy.shevchenko@linux.intel.com
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This makes the error handling much more simpler than open-coding everything
and in addition makes the probe function smaller an tidier.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220207210730.75252-5-andriy.shevchenko@linux.intel.com
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Eliminate some boilerplate code by using module_pci_driver() instead of
init/exit, and, if needed, moving the salient bits from init into probe.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220207210730.75252-4-andriy.shevchenko@linux.intel.com
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There is already helper functions to do 64-bit I/O on 32-bit machines or
buses, thus we don't need to reinvent the wheel.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220207210730.75252-3-andriy.shevchenko@linux.intel.com
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
