mirror of
https://mirrors.bfsu.edu.cn/git/linux.git
synced 2024-11-11 21:38:32 +08:00
ac8813c0ab
445 Commits
| Author | SHA1 | Message | Date | |
|---|---|---|---|---|
Gal Pressman
|
f8e82440d9 |
ptp: ptp_ines: Remove setting of RX software timestamp
The responsibility for reporting of RX software timestamp has moved to the core layer (see __ethtool_get_ts_info()), remove usage from the device drivers. Reviewed-by: Carolina Jubran <cjubran@nvidia.com> Reviewed-by: Rahul Rameshbabu <rrameshbabu@nvidia.com> Signed-off-by: Gal Pressman <gal@nvidia.com> Link: https://patch.msgid.link/20240906144632.404651-17-gal@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> |
||
Mahesh Bandewar
|
c259acab83 |
ptp/ioctl: support MONOTONIC{,_RAW} timestamps for PTP_SYS_OFFSET_EXTENDED
The ability to read the PHC (Physical Hardware Clock) alongside multiple system clocks is currently dependent on the specific hardware architecture. This limitation restricts the use of PTP_SYS_OFFSET_PRECISE to certain hardware configurations. The generic soultion which would work across all architectures is to read the PHC along with the latency to perform PHC-read as offered by PTP_SYS_OFFSET_EXTENDED which provides pre and post timestamps. However, these timestamps are currently limited to the CLOCK_REALTIME timebase. Since CLOCK_REALTIME is affected by NTP (or similar time synchronization services), it can experience significant jumps forward or backward. This hinders the precise latency measurements that PTP_SYS_OFFSET_EXTENDED is designed to provide. This problem could be addressed by supporting MONOTONIC_RAW timestamps within PTP_SYS_OFFSET_EXTENDED. Unlike CLOCK_REALTIME or CLOCK_MONOTONIC, the MONOTONIC_RAW timebase is unaffected by NTP adjustments. This enhancement can be implemented by utilizing one of the three reserved words within the PTP_SYS_OFFSET_EXTENDED struct to pass the clock-id for timestamps. The current behavior aligns with clock-id for CLOCK_REALTIME timebase (value of 0), ensuring backward compatibility of the UAPI. Signed-off-by: Mahesh Bandewar <maheshb@google.com> Signed-off-by: Vadim Fedorenko <vadfed@meta.com> Signed-off-by: David S. Miller <davem@davemloft.net> |
||
Vadim Fedorenko
|
aa05fe67bc |
ptp: ocp: Improve PCIe delay estimation
The PCIe bus can be pretty busy during boot and probe function can see excessive delays. Let's find the minimal value out of several tests and use it as estimated value. Signed-off-by: Vadim Fedorenko <vadim.fedorenko@linux.dev> Link: https://patch.msgid.link/20240905140028.560454-1-vadim.fedorenko@linux.dev Signed-off-by: Jakub Kicinski <kuba@kernel.org> |
||
Jakub Kicinski
|
502cc061de |
Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Cross-merge networking fixes after downstream PR. Conflicts: drivers/net/phy/phy_device.c |
||
Chen Ni
|
335cc75ce3 |
ptp: ptp_idt82p33: Convert comma to semicolon
Replace comma between expressions with semicolons. Using a ',' in place of a ';' can have unintended side effects. Although that is not the case here, it is seems best to use ';' unless ',' is intended. Found by inspection. No functional change intended. Compile tested only. Signed-off-by: Chen Ni <nichen@iscas.ac.cn> Acked-by: Richard Cochran <richardcochran@gmail.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20240904015003.1065872-1-nichen@iscas.ac.cn Signed-off-by: Paolo Abeni <pabeni@redhat.com> |
||
Vadim Fedorenko
|
82ace0c8fe |
ptp: ocp: adjust sysfs entries to expose tty information
Implement additional attribute group to expose serial port information.
Fixes tag points to the commit which introduced the change in serial
port subsystem and made it impossible to use symlinks.
Fixes:
|
||
|
Vadim Fedorenko
|
d7875b4b07 |
ptp: ocp: convert serial ports to array
Simplify serial port management code by using array of ports and helpers to get the name of the port. This change is needed to make the next patch simplier. Signed-off-by: Vadim Fedorenko <vadfed@meta.com> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Paolo Abeni <pabeni@redhat.com> |
||
Linus Torvalds
|
51835949dd |
Networking changes for 6.11. Not much excitement - a handful of large
patchsets (devmem among them) did not make it in time.
Core & protocols
----------------
- Use local_lock in addition to local_bh_disable() to protect per-CPU
resources in networking, a step closer for local_bh_disable() not
to act as a big lock on PREEMPT_RT.
- Use flex array for netdevice priv area, ensure its cache alignment.
- Add a sysctl knob to allow user to specify a default rto_min at socket
init time. Bit of a big hammer but multiple companies were
independently carrying such patch downstream so clearly it's useful.
- Support scheduling transmission of packets based on CLOCK_TAI.
- Un-pin TCP TIMEWAIT timer to avoid it firing on CPUs later cordoned off
using cpusets.
- Support multiple L2TPv3 UDP tunnels using the same 5-tuple address.
- Allow configuration of multipath hash seed, to both allow synchronizing
hashing of two routers, and preventing partial accidental sync.
- Improve TCP compliance with RFC 9293 for simultaneous connect().
- Support sending NAT keepalives in IPsec ESP in UDP states. Userspace
IKE daemon had to do this before, but the kernel can better keep
track of it.
- Support sending supervision HSR frames with MAC addresses stored in
ProxyNodeTable when RedBox (i.e. HSR-SAN) is enabled.
- Introduce IPPROTO_SMC for selecting SMC when socket is created.
- Allow UDP GSO transmit from devices with no checksum offload.
- openvswitch: add packet sampling via psample, separating the sampled
traffic from "upcall" packets sent to user space for forwarding.
- nf_tables: shrink memory consumption for transaction objects.
Things we sprinkled into general kernel code
--------------------------------------------
- Power Sequencing subsystem (used by Qualcomm Bluetooth driver
for QCA6390).
- Add IRQ information in sysfs for auxiliary bus.
- Introduce guard definition for local_lock.
- Add aligned flavor of __cacheline_group_{begin, end}() markings for
grouping fields in structures.
BPF
---
- Notify user space (via epoll) when a struct_ops object is getting
detached/unregistered.
- Add new kfuncs for a generic, open-coded bits iterator.
- Enable BPF programs to declare arrays of kptr, bpf_rb_root, and
bpf_list_head.
- Support resilient split BTF which cuts down on duplication and makes
BTF as compact as possible WRT BTF from modules.
- Add support for dumping kfunc prototypes from BTF which enables both
detecting as well as dumping compilable prototypes for kfuncs.
- riscv64 BPF JIT improvements in particular to add 12-argument support
for BPF trampolines and to utilize bpf_prog_pack for the latter.
- Add the capability to offload the netfilter flowtable in XDP layer
through kfuncs.
Driver API
----------
- Allow users to configure IRQ tresholds between which automatic IRQ
moderation can choose.
- Expand Power Sourcing (PoE) status with power, class and failure
reason. Support setting power limits.
- Track additional RSS contexts in the core, make sure configuration
changes don't break them.
- Support IPsec crypto offload for IPv6 ESP and IPv4 UDP-encapsulated ESP
data paths.
- Support updating firmware on SFP modules.
Tests and tooling
-----------------
- mptcp: use net/lib.sh to manage netns.
- TCP-AO and TCP-MD5: replace debug prints used by tests with
tracepoints.
- openvswitch: make test self-contained (don't depend on OvS CLI tools).
Drivers
-------
- Ethernet high-speed NICs:
- Broadcom (bnxt):
- increase the max total outstanding PTP TX packets to 4
- add timestamping statistics support
- implement netdev_queue_mgmt_ops
- support new RSS context API
- Intel (100G, ice, idpf):
- implement FEC statistics and dumping signal quality indicators
- support E825C products (with 56Gbps PHYs)
- nVidia/Mellanox:
- support HW-GRO
- mlx4/mlx5: support per-queue statistics via netlink
- obey the max number of EQs setting in sub-functions
- AMD/Solarflare:
- support new RSS context API
- AMD/Pensando:
- ionic: rework fix for doorbell miss to lower overhead
and skip it on new HW
- Wangxun:
- txgbe: support Flow Director perfect filters
- Ethernet NICs consumer, embedded and virtual:
- Add driver for Tehuti Networks TN40xx chips
- Add driver for Meta's internal NIC chips
- Add driver for Ethernet MAC on Airoha EN7581 SoCs
- Add driver for Renesas Ethernet-TSN devices
- Google cloud vNIC:
- flow steering support
- Microsoft vNIC:
- support page sizes other than 4KB on ARM64
- vmware vNIC:
- support latency measurement (update to version 9)
- VirtIO net:
- support for Byte Queue Limits
- support configuring thresholds for automatic IRQ moderation
- support for AF_XDP Rx zero-copy
- Synopsys (stmmac):
- support for STM32MP13 SoC
- let platforms select the right PCS implementation
- TI:
- icssg-prueth: add multicast filtering support
- icssg-prueth: enable PTP timestamping and PPS
- Renesas:
- ravb: improve Rx performance 30-400% by using page pool,
theaded NAPI and timer-based IRQ coalescing
- ravb: add MII support for R-Car V4M
- Cadence (macb):
- macb: add ARP support to Wake-On-LAN
- Cortina:
- use phylib for RX and TX pause configuration
- Ethernet switches:
- nVidia/Mellanox:
- support configuration of multipath hash seed
- report more accurate max MTU
- use page_pool to improve Rx performance
- MediaTek:
- mt7530: add support for bridge port isolation
- Qualcomm:
- qca8k: add support for bridge port isolation
- Microchip:
- lan9371/2: add 100BaseTX PHY support
- NXP:
- vsc73xx: implement VLAN operations
- Ethernet PHYs:
- aquantia: enable support for aqr115c
- aquantia: add support for PHY LEDs
- realtek: add support for rtl8224 2.5Gbps PHY
- xpcs: add memory-mapped device support
- add BroadR-Reach link mode and support in Broadcom's PHY driver
- CAN:
- add document for ISO 15765-2 protocol support
- mcp251xfd: workaround for erratum DS80000789E, use timestamps
to catch when device returns incorrect FIFO status
- WiFi:
- mac80211/cfg80211:
- parse Transmit Power Envelope (TPE) data in mac80211 instead of
in drivers
- improvements for 6 GHz regulatory flexibility
- multi-link improvements
- support multiple radios per wiphy
- remove DEAUTH_NEED_MGD_TX_PREP flag
- Intel (iwlwifi):
- bump FW API to 91 for BZ/SC devices
- report 64-bit radiotap timestamp
- enable P2P low latency by default
- handle Transmit Power Envelope (TPE) advertised by AP
- remove support for older FW for new devices
- fast resume (keeping the device configured)
- mvm: re-enable Multi-Link Operation (MLO)
- aggregation (A-MSDU) optimizations
- MediaTek (mt76):
- mt7925 Multi-Link Operation (MLO) support
- Qualcomm (ath10k):
- LED support for various chipsets
- Qualcomm (ath12k):
- remove unsupported Tx monitor handling
- support channel 2 in 6 GHz band
- support Spatial Multiplexing Power Save (SMPS) in 6 GHz band
- supprt multiple BSSID (MBSSID) and Enhanced Multi-BSSID
Advertisements (EMA)
- support dynamic VLAN
- add panic handler for resetting the firmware state
- DebugFS support for datapath statistics
- WCN7850: support for Wake on WLAN
- Microchip (wilc1000):
- read MAC address during probe to make it visible to user space
- suspend/resume improvements
- TI (wl18xx):
- support newer firmware versions
- RealTek (rtw89):
- preparation for RTL8852BE-VT support
- Wake on WLAN support for WiFi 6 chips
- 36-bit PCI DMA support
- RealTek (rtlwifi):
- RTL8192DU support
- Broadcom (brcmfmac):
- Management Frame Protection support (to enable WPA3)
- Bluetooth:
- qualcomm: use the power sequencer for QCA6390
- btusb: mediatek: add ISO data transmission functions
- hci_bcm4377: add BCM4388 support
- btintel: add support for BlazarU core
- btintel: add support for Whale Peak2
- btnxpuart: add support for AW693 A1 chipset
- btnxpuart: add support for IW615 chipset
- btusb: add Realtek RTL8852BE support ID 0x13d3:0x3591
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=opz8
-----END PGP SIGNATURE-----
Merge tag 'net-next-6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Not much excitement - a handful of large patchsets (devmem among them)
did not make it in time.
Core & protocols:
- Use local_lock in addition to local_bh_disable() to protect per-CPU
resources in networking, a step closer for local_bh_disable() not
to act as a big lock on PREEMPT_RT
- Use flex array for netdevice priv area, ensure its cache alignment
- Add a sysctl knob to allow user to specify a default rto_min at
socket init time. Bit of a big hammer but multiple companies were
independently carrying such patch downstream so clearly it's useful
- Support scheduling transmission of packets based on CLOCK_TAI
- Un-pin TCP TIMEWAIT timer to avoid it firing on CPUs later cordoned
off using cpusets
- Support multiple L2TPv3 UDP tunnels using the same 5-tuple address
- Allow configuration of multipath hash seed, to both allow
synchronizing hashing of two routers, and preventing partial
accidental sync
- Improve TCP compliance with RFC 9293 for simultaneous connect()
- Support sending NAT keepalives in IPsec ESP in UDP states.
Userspace IKE daemon had to do this before, but the kernel can
better keep track of it
- Support sending supervision HSR frames with MAC addresses stored in
ProxyNodeTable when RedBox (i.e. HSR-SAN) is enabled
- Introduce IPPROTO_SMC for selecting SMC when socket is created
- Allow UDP GSO transmit from devices with no checksum offload
- openvswitch: add packet sampling via psample, separating the
sampled traffic from "upcall" packets sent to user space for
forwarding
- nf_tables: shrink memory consumption for transaction objects
Things we sprinkled into general kernel code:
- Power Sequencing subsystem (used by Qualcomm Bluetooth driver for
QCA6390) [ Already merged separately - Linus ]
- Add IRQ information in sysfs for auxiliary bus
- Introduce guard definition for local_lock
- Add aligned flavor of __cacheline_group_{begin, end}() markings for
grouping fields in structures
BPF:
- Notify user space (via epoll) when a struct_ops object is getting
detached/unregistered
- Add new kfuncs for a generic, open-coded bits iterator
- Enable BPF programs to declare arrays of kptr, bpf_rb_root, and
bpf_list_head
- Support resilient split BTF which cuts down on duplication and
makes BTF as compact as possible WRT BTF from modules
- Add support for dumping kfunc prototypes from BTF which enables
both detecting as well as dumping compilable prototypes for kfuncs
- riscv64 BPF JIT improvements in particular to add 12-argument
support for BPF trampolines and to utilize bpf_prog_pack for the
latter
- Add the capability to offload the netfilter flowtable in XDP layer
through kfuncs
Driver API:
- Allow users to configure IRQ tresholds between which automatic IRQ
moderation can choose
- Expand Power Sourcing (PoE) status with power, class and failure
reason. Support setting power limits
- Track additional RSS contexts in the core, make sure configuration
changes don't break them
- Support IPsec crypto offload for IPv6 ESP and IPv4 UDP-encapsulated
ESP data paths
- Support updating firmware on SFP modules
Tests and tooling:
- mptcp: use net/lib.sh to manage netns
- TCP-AO and TCP-MD5: replace debug prints used by tests with
tracepoints
- openvswitch: make test self-contained (don't depend on OvS CLI
tools)
Drivers:
- Ethernet high-speed NICs:
- Broadcom (bnxt):
- increase the max total outstanding PTP TX packets to 4
- add timestamping statistics support
- implement netdev_queue_mgmt_ops
- support new RSS context API
- Intel (100G, ice, idpf):
- implement FEC statistics and dumping signal quality indicators
- support E825C products (with 56Gbps PHYs)
- nVidia/Mellanox:
- support HW-GRO
- mlx4/mlx5: support per-queue statistics via netlink
- obey the max number of EQs setting in sub-functions
- AMD/Solarflare:
- support new RSS context API
- AMD/Pensando:
- ionic: rework fix for doorbell miss to lower overhead and
skip it on new HW
- Wangxun:
- txgbe: support Flow Director perfect filters
- Ethernet NICs consumer, embedded and virtual:
- Add driver for Tehuti Networks TN40xx chips
- Add driver for Meta's internal NIC chips
- Add driver for Ethernet MAC on Airoha EN7581 SoCs
- Add driver for Renesas Ethernet-TSN devices
- Google cloud vNIC:
- flow steering support
- Microsoft vNIC:
- support page sizes other than 4KB on ARM64
- vmware vNIC:
- support latency measurement (update to version 9)
- VirtIO net:
- support for Byte Queue Limits
- support configuring thresholds for automatic IRQ moderation
- support for AF_XDP Rx zero-copy
- Synopsys (stmmac):
- support for STM32MP13 SoC
- let platforms select the right PCS implementation
- TI:
- icssg-prueth: add multicast filtering support
- icssg-prueth: enable PTP timestamping and PPS
- Renesas:
- ravb: improve Rx performance 30-400% by using page pool,
theaded NAPI and timer-based IRQ coalescing
- ravb: add MII support for R-Car V4M
- Cadence (macb):
- macb: add ARP support to Wake-On-LAN
- Cortina:
- use phylib for RX and TX pause configuration
- Ethernet switches:
- nVidia/Mellanox:
- support configuration of multipath hash seed
- report more accurate max MTU
- use page_pool to improve Rx performance
- MediaTek:
- mt7530: add support for bridge port isolation
- Qualcomm:
- qca8k: add support for bridge port isolation
- Microchip:
- lan9371/2: add 100BaseTX PHY support
- NXP:
- vsc73xx: implement VLAN operations
- Ethernet PHYs:
- aquantia: enable support for aqr115c
- aquantia: add support for PHY LEDs
- realtek: add support for rtl8224 2.5Gbps PHY
- xpcs: add memory-mapped device support
- add BroadR-Reach link mode and support in Broadcom's PHY driver
- CAN:
- add document for ISO 15765-2 protocol support
- mcp251xfd: workaround for erratum DS80000789E, use timestamps to
catch when device returns incorrect FIFO status
- WiFi:
- mac80211/cfg80211:
- parse Transmit Power Envelope (TPE) data in mac80211 instead
of in drivers
- improvements for 6 GHz regulatory flexibility
- multi-link improvements
- support multiple radios per wiphy
- remove DEAUTH_NEED_MGD_TX_PREP flag
- Intel (iwlwifi):
- bump FW API to 91 for BZ/SC devices
- report 64-bit radiotap timestamp
- enable P2P low latency by default
- handle Transmit Power Envelope (TPE) advertised by AP
- remove support for older FW for new devices
- fast resume (keeping the device configured)
- mvm: re-enable Multi-Link Operation (MLO)
- aggregation (A-MSDU) optimizations
- MediaTek (mt76):
- mt7925 Multi-Link Operation (MLO) support
- Qualcomm (ath10k):
- LED support for various chipsets
- Qualcomm (ath12k):
- remove unsupported Tx monitor handling
- support channel 2 in 6 GHz band
- support Spatial Multiplexing Power Save (SMPS) in 6 GHz band
- supprt multiple BSSID (MBSSID) and Enhanced Multi-BSSID
Advertisements (EMA)
- support dynamic VLAN
- add panic handler for resetting the firmware state
- DebugFS support for datapath statistics
- WCN7850: support for Wake on WLAN
- Microchip (wilc1000):
- read MAC address during probe to make it visible to user space
- suspend/resume improvements
- TI (wl18xx):
- support newer firmware versions
- RealTek (rtw89):
- preparation for RTL8852BE-VT support
- Wake on WLAN support for WiFi 6 chips
- 36-bit PCI DMA support
- RealTek (rtlwifi):
- RTL8192DU support
- Broadcom (brcmfmac):
- Management Frame Protection support (to enable WPA3)
- Bluetooth:
- qualcomm: use the power sequencer for QCA6390
- btusb: mediatek: add ISO data transmission functions
- hci_bcm4377: add BCM4388 support
- btintel: add support for BlazarU core
- btintel: add support for Whale Peak2
- btnxpuart: add support for AW693 A1 chipset
- btnxpuart: add support for IW615 chipset
- btusb: add Realtek RTL8852BE support ID 0x13d3:0x3591"
* tag 'net-next-6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1589 commits)
eth: fbnic: Fix spelling mistake "tiggerring" -> "triggering"
tcp: Replace strncpy() with strscpy()
wifi: ath12k: fix build vs old compiler
tcp: Don't access uninit tcp_rsk(req)->ao_keyid in tcp_create_openreq_child().
eth: fbnic: Write the TCAM tables used for RSS control and Rx to host
eth: fbnic: Add L2 address programming
eth: fbnic: Add basic Rx handling
eth: fbnic: Add basic Tx handling
eth: fbnic: Add link detection
eth: fbnic: Add initial messaging to notify FW of our presence
eth: fbnic: Implement Rx queue alloc/start/stop/free
eth: fbnic: Implement Tx queue alloc/start/stop/free
eth: fbnic: Allocate a netdevice and napi vectors with queues
eth: fbnic: Add FW communication mechanism
eth: fbnic: Add message parsing for FW messages
eth: fbnic: Add register init to set PCIe/Ethernet device config
eth: fbnic: Allocate core device specific structures and devlink interface
eth: fbnic: Add scaffolding for Meta's NIC driver
PCI: Add Meta Platforms vendor ID
net/sched: cls_flower: propagate tca[TCA_OPTIONS] to NL_REQ_ATTR_CHECK
...
|
||
Kory Maincent
|
2111375b85 |
net: Add struct kernel_ethtool_ts_info
In prevision to add new UAPI for hwtstamp we will be limited to the struct ethtool_ts_info that is currently passed in fixed binary format through the ETHTOOL_GET_TS_INFO ethtool ioctl. It would be good if new kernel code already started operating on an extensible kernel variant of that structure, similar in concept to struct kernel_hwtstamp_config vs struct hwtstamp_config. Since struct ethtool_ts_info is in include/uapi/linux/ethtool.h, here we introduce the kernel-only structure in include/linux/ethtool.h. The manual copy is then made in the function called by ETHTOOL_GET_TS_INFO. Acked-by: Shannon Nelson <shannon.nelson@amd.com> Acked-by: Alexandra Winter <wintera@linux.ibm.com> Signed-off-by: Kory Maincent <kory.maincent@bootlin.com> Link: https://patch.msgid.link/20240709-feature_ptp_netnext-v17-6-b5317f50df2a@bootlin.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> |
||
Alexey Makhalov
|
54651bb4dc |
ptp/vmware: Use VMware hypercall API
Switch from VMWARE_HYPERCALL macro to vmware_hypercall API. Eliminate arch specific code. No functional changes intended. Signed-off-by: Alexey Makhalov <alexey.makhalov@broadcom.com> Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de> Link: https://lore.kernel.org/r/20240613191650.9913-3-alexey.makhalov@broadcom.com |
||
Dan Carpenter
|
81d23d2a24 |
ptp: fix integer overflow in max_vclocks_store
On 32bit systems, the "4 * max" multiply can overflow. Use kcalloc()
to do the allocation to prevent this.
Fixes:
|
||
Karol Kolacinski
|
323a359f9b |
ptp: Fix error message on failed pin verification
On failed verification of PTP clock pin, error message prints channel
number instead of pin index after "pin", which is incorrect.
Fix error message by adding channel number to the message and printing
pin number instead of channel number.
Fixes:
|
||
|
Linus Torvalds
|
1b294a1f35 |
Networking changes for 6.10.
Core & protocols
----------------
- Complete rework of garbage collection of AF_UNIX sockets.
AF_UNIX is prone to forming reference count cycles due to fd passing
functionality. New method based on Tarjan's Strongly Connected Components
algorithm should be both faster and remove a lot of workarounds
we accumulated over the years.
- Add TCP fraglist GRO support, allowing chaining multiple TCP packets
and forwarding them together. Useful for small switches / routers which
lack basic checksum offload in some scenarios (e.g. PPPoE).
- Support using SMP threads for handling packet backlog i.e. packet
processing from software interfaces and old drivers which don't
use NAPI. This helps move the processing out of the softirq jumble.
- Continue work of converting from rtnl lock to RCU protection.
Don't require rtnl lock when reading: IPv6 routing FIB, IPv6 address
labels, netdev threaded NAPI sysfs files, bonding driver's sysfs files,
MPLS devconf, IPv4 FIB rules, netns IDs, tcp metrics, TC Qdiscs,
neighbor entries, ARP entries via ioctl(SIOCGARP), a lot of the link
information available via rtnetlink.
- Small optimizations from Eric to UDP wake up handling, memory accounting,
RPS/RFS implementation, TCP packet sizing etc.
- Allow direct page recycling in the bulk API used by XDP, for +2% PPS.
- Support peek with an offset on TCP sockets.
- Add MPTCP APIs for querying last time packets were received/sent/acked,
and whether MPTCP "upgrade" succeeded on a TCP socket.
- Add intra-node communication shortcut to improve SMC performance.
- Add IPv6 (and IPv{4,6}-over-IPv{4,6}) support to the GTP protocol driver.
- Add HSR-SAN (RedBOX) mode of operation to the HSR protocol driver.
- Add reset reasons for tracing what caused a TCP reset to be sent.
- Introduce direction attribute for xfrm (IPSec) states.
State can be used either for input or output packet processing.
Things we sprinkled into general kernel code
--------------------------------------------
- Add bitmap_{read,write}(), bitmap_size(), expose BYTES_TO_BITS().
This required touch-ups and renaming of a few existing users.
- Add Endian-dependent __counted_by_{le,be} annotations.
- Make building selftests "quieter" by printing summaries like
"CC object.o" rather than full commands with all the arguments.
Netfilter
---------
- Use GFP_KERNEL to clone elements, to deal better with OOM situations
and avoid failures in the .commit step.
BPF
---
- Add eBPF JIT for ARCv2 CPUs.
- Support attaching kprobe BPF programs through kprobe_multi link in
a session mode, meaning, a BPF program is attached to both function entry
and return, the entry program can decide if the return program gets
executed and the entry program can share u64 cookie value with return
program. "Session mode" is a common use-case for tetragon and bpftrace.
- Add the ability to specify and retrieve BPF cookie for raw tracepoint
programs in order to ease migration from classic to raw tracepoints.
- Add an internal-only BPF per-CPU instruction for resolving per-CPU
memory addresses and implement support in x86, ARM64 and RISC-V JITs.
This allows inlining functions which need to access per-CPU state.
- Optimize x86 BPF JIT's emit_mov_imm64, and add support for various
atomics in bpf_arena which can be JITed as a single x86 instruction.
Support BPF arena on ARM64.
- Add a new bpf_wq API for deferring events and refactor process-context
bpf_timer code to keep common code where possible.
- Harden the BPF verifier's and/or/xor value tracking.
- Introduce crypto kfuncs to let BPF programs call kernel crypto APIs.
- Support bpf_tail_call_static() helper for BPF programs with GCC 13.
- Add bpf_preempt_{disable,enable}() kfuncs in order to allow a BPF
program to have code sections where preemption is disabled.
Driver API
----------
- Skip software TC processing completely if all installed rules are
marked as HW-only, instead of checking the HW-only flag rule by rule.
- Add support for configuring PoE (Power over Ethernet), similar to
the already existing support for PoDL (Power over Data Line) config.
- Initial bits of a queue control API, for now allowing a single queue
to be reset without disturbing packet flow to other queues.
- Common (ethtool) statistics for hardware timestamping.
Tests and tooling
-----------------
- Remove the need to create a config file to run the net forwarding tests
so that a naive "make run_tests" can exercise them.
- Define a method of writing tests which require an external endpoint
to communicate with (to send/receive data towards the test machine).
Add a few such tests.
- Create a shared code library for writing Python tests. Expose the YAML
Netlink library from tools/ to the tests for easy Netlink access.
- Move netfilter tests under net/, extend them, separate performance tests
from correctness tests, and iron out issues found by running them
"on every commit".
- Refactor BPF selftests to use common network helpers.
- Further work filling in YAML definitions of Netlink messages for:
nftables, team driver, bonding interfaces, vlan interfaces, VF info,
TC u32 mark, TC police action.
- Teach Python YAML Netlink to decode attribute policies.
- Extend the definition of the "indexed array" construct in the specs
to cover arrays of scalars rather than just nests.
- Add hyperlinks between definitions in generated Netlink docs.
Drivers
-------
- Make sure unsupported flower control flags are rejected by drivers,
and make more drivers report errors directly to the application rather
than dmesg (large number of driver changes from Asbjørn Sloth Tønnesen).
- Ethernet high-speed NICs:
- Broadcom (bnxt):
- support multiple RSS contexts and steering traffic to them
- support XDP metadata
- make page pool allocations more NUMA aware
- Intel (100G, ice, idpf):
- extract datapath code common among Intel drivers into a library
- use fewer resources in switchdev by sharing queues with the PF
- add PFCP filter support
- add Ethernet filter support
- use a spinlock instead of HW lock in PTP clock ops
- support 5 layer Tx scheduler topology
- nVidia/Mellanox:
- 800G link modes and 100G SerDes speeds
- per-queue IRQ coalescing configuration
- Marvell Octeon:
- support offloading TC packet mark action
- Ethernet NICs consumer, embedded and virtual:
- stop lying about skb->truesize in USB Ethernet drivers, it messes up
TCP memory calculations
- Google cloud vNIC:
- support changing ring size via ethtool
- support ring reset using the queue control API
- VirtIO net:
- expose flow hash from RSS to XDP
- per-queue statistics
- add selftests
- Synopsys (stmmac):
- support controllers which require an RX clock signal from the MII
bus to perform their hardware initialization
- TI:
- icssg_prueth: support ICSSG-based Ethernet on AM65x SR1.0 devices
- icssg_prueth: add SW TX / RX Coalescing based on hrtimers
- cpsw: minimal XDP support
- Renesas (ravb):
- support describing the MDIO bus
- Realtek (r8169):
- add support for RTL8168M
- Microchip Sparx5:
- matchall and flower actions mirred and redirect
- Ethernet switches:
- nVidia/Mellanox:
- improve events processing performance
- Marvell:
- add support for MV88E6250 family internal PHYs
- Microchip:
- add DCB and DSCP mapping support for KSZ switches
- vsc73xx: convert to PHYLINK
- Realtek:
- rtl8226b/rtl8221b: add C45 instances and SerDes switching
- Many driver changes related to PHYLIB and PHYLINK deprecated API cleanup.
- Ethernet PHYs:
- Add a new driver for Airoha EN8811H 2.5 Gigabit PHY.
- micrel: lan8814: add support for PPS out and external timestamp trigger
- WiFi:
- Disable Wireless Extensions (WEXT) in all Wi-Fi 7 devices drivers.
Modern devices can only be configured using nl80211.
- mac80211/cfg80211
- handle color change per link for WiFi 7 Multi-Link Operation
- Intel (iwlwifi):
- don't support puncturing in 5 GHz
- support monitor mode on passive channels
- BZ-W device support
- P2P with HE/EHT support
- re-add support for firmware API 90
- provide channel survey information for Automatic Channel Selection
- MediaTek (mt76):
- mt7921 LED control
- mt7925 EHT radiotap support
- mt7920e PCI support
- Qualcomm (ath11k):
- P2P support for QCA6390, WCN6855 and QCA2066
- support hibernation
- ieee80211-freq-limit Device Tree property support
- Qualcomm (ath12k):
- refactoring in preparation of multi-link support
- suspend and hibernation support
- ACPI support
- debugfs support, including dfs_simulate_radar support
- RealTek:
- rtw88: RTL8723CS SDIO device support
- rtw89: RTL8922AE Wi-Fi 7 PCI device support
- rtw89: complete features of new WiFi 7 chip 8922AE including
BT-coexistence and Wake-on-WLAN
- rtw89: use BIOS ACPI settings to set TX power and channels
- rtl8xxxu: enable Management Frame Protection (MFP) support
- Bluetooth:
- support for Intel BlazarI and Filmore Peak2 (BE201)
- support for MediaTek MT7921S SDIO
- initial support for Intel PCIe BT driver
- remove HCI_AMP support
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEE6jPA+I1ugmIBA4hXMUZtbf5SIrsFAmZD6sQACgkQMUZtbf5S
IrtLYw/+I73ePGIye37o2jpbodcLAUZVfF3r6uYUzK8hokEcKD0QVJa9w7PizLZ3
UO45ClOXFLJCkfP4reFenLfxGCel2AJI+F7VFl2xaO2XgrcH/lnVrHqKZEAEXjls
KoYMnShIolv7h2MKP6hHtyTi2j1wvQUKsZC71o9/fuW+4fUT8gECx1YtYcL73wrw
gEMdlUgBYC3jiiCUHJIFX6iPJ2t/TC+q1eIIF2K/Osrk2kIqQhzoozcL4vpuAZQT
99ljx/qRelXa8oppDb7nM5eulg7WY8ZqxEfFZphTMC5nLEGzClxuOTTl2kDYI/D/
UZmTWZDY+F5F0xvNk2gH84qVJXBOVDoobpT7hVA/tDuybobc/kvGDzRayEVqVzKj
Q0tPlJs+xBZpkK5TVnxaFLJVOM+p1Xosxy3kNVXmuYNBvT/R89UbJiCrUKqKZF+L
z/1mOYUv8UklHqYAeuJSptHvqJjTGa/fsEYP7dAUBbc1N2eVB8mzZ4mgU5rYXbtC
E6UXXiWnoSRm8bmco9QmcWWoXt5UGEizHSJLz6t1R5Df/YmXhWlytll5aCwY1ksf
FNoL7S4u7AZThL1Nwi7yUs4CAjhk/N4aOsk+41S0sALCx30BJuI6UdesAxJ0lu+Z
fwCQYbs27y4p7mBLbkYwcQNxAxGm7PSK4yeyRIy2njiyV4qnLf8=
=EsC2
-----END PGP SIGNATURE-----
Merge tag 'net-next-6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Core & protocols:
- Complete rework of garbage collection of AF_UNIX sockets.
AF_UNIX is prone to forming reference count cycles due to fd
passing functionality. New method based on Tarjan's Strongly
Connected Components algorithm should be both faster and remove a
lot of workarounds we accumulated over the years.
- Add TCP fraglist GRO support, allowing chaining multiple TCP
packets and forwarding them together. Useful for small switches /
routers which lack basic checksum offload in some scenarios (e.g.
PPPoE).
- Support using SMP threads for handling packet backlog i.e. packet
processing from software interfaces and old drivers which don't use
NAPI. This helps move the processing out of the softirq jumble.
- Continue work of converting from rtnl lock to RCU protection.
Don't require rtnl lock when reading: IPv6 routing FIB, IPv6
address labels, netdev threaded NAPI sysfs files, bonding driver's
sysfs files, MPLS devconf, IPv4 FIB rules, netns IDs, tcp metrics,
TC Qdiscs, neighbor entries, ARP entries via ioctl(SIOCGARP), a lot
of the link information available via rtnetlink.
- Small optimizations from Eric to UDP wake up handling, memory
accounting, RPS/RFS implementation, TCP packet sizing etc.
- Allow direct page recycling in the bulk API used by XDP, for +2%
PPS.
- Support peek with an offset on TCP sockets.
- Add MPTCP APIs for querying last time packets were received/sent/acked
and whether MPTCP "upgrade" succeeded on a TCP socket.
- Add intra-node communication shortcut to improve SMC performance.
- Add IPv6 (and IPv{4,6}-over-IPv{4,6}) support to the GTP protocol
driver.
- Add HSR-SAN (RedBOX) mode of operation to the HSR protocol driver.
- Add reset reasons for tracing what caused a TCP reset to be sent.
- Introduce direction attribute for xfrm (IPSec) states. State can be
used either for input or output packet processing.
Things we sprinkled into general kernel code:
- Add bitmap_{read,write}(), bitmap_size(), expose BYTES_TO_BITS().
This required touch-ups and renaming of a few existing users.
- Add Endian-dependent __counted_by_{le,be} annotations.
- Make building selftests "quieter" by printing summaries like
"CC object.o" rather than full commands with all the arguments.
Netfilter:
- Use GFP_KERNEL to clone elements, to deal better with OOM
situations and avoid failures in the .commit step.
BPF:
- Add eBPF JIT for ARCv2 CPUs.
- Support attaching kprobe BPF programs through kprobe_multi link in
a session mode, meaning, a BPF program is attached to both function
entry and return, the entry program can decide if the return
program gets executed and the entry program can share u64 cookie
value with return program. "Session mode" is a common use-case for
tetragon and bpftrace.
- Add the ability to specify and retrieve BPF cookie for raw
tracepoint programs in order to ease migration from classic to raw
tracepoints.
- Add an internal-only BPF per-CPU instruction for resolving per-CPU
memory addresses and implement support in x86, ARM64 and RISC-V
JITs. This allows inlining functions which need to access per-CPU
state.
- Optimize x86 BPF JIT's emit_mov_imm64, and add support for various
atomics in bpf_arena which can be JITed as a single x86
instruction. Support BPF arena on ARM64.
- Add a new bpf_wq API for deferring events and refactor
process-context bpf_timer code to keep common code where possible.
- Harden the BPF verifier's and/or/xor value tracking.
- Introduce crypto kfuncs to let BPF programs call kernel crypto
APIs.
- Support bpf_tail_call_static() helper for BPF programs with GCC 13.
- Add bpf_preempt_{disable,enable}() kfuncs in order to allow a BPF
program to have code sections where preemption is disabled.
Driver API:
- Skip software TC processing completely if all installed rules are
marked as HW-only, instead of checking the HW-only flag rule by
rule.
- Add support for configuring PoE (Power over Ethernet), similar to
the already existing support for PoDL (Power over Data Line)
config.
- Initial bits of a queue control API, for now allowing a single
queue to be reset without disturbing packet flow to other queues.
- Common (ethtool) statistics for hardware timestamping.
Tests and tooling:
- Remove the need to create a config file to run the net forwarding
tests so that a naive "make run_tests" can exercise them.
- Define a method of writing tests which require an external endpoint
to communicate with (to send/receive data towards the test
machine). Add a few such tests.
- Create a shared code library for writing Python tests. Expose the
YAML Netlink library from tools/ to the tests for easy Netlink
access.
- Move netfilter tests under net/, extend them, separate performance
tests from correctness tests, and iron out issues found by running
them "on every commit".
- Refactor BPF selftests to use common network helpers.
- Further work filling in YAML definitions of Netlink messages for:
nftables, team driver, bonding interfaces, vlan interfaces, VF
info, TC u32 mark, TC police action.
- Teach Python YAML Netlink to decode attribute policies.
- Extend the definition of the "indexed array" construct in the specs
to cover arrays of scalars rather than just nests.
- Add hyperlinks between definitions in generated Netlink docs.
Drivers:
- Make sure unsupported flower control flags are rejected by drivers,
and make more drivers report errors directly to the application
rather than dmesg (large number of driver changes from Asbjørn
Sloth Tønnesen).
- Ethernet high-speed NICs:
- Broadcom (bnxt):
- support multiple RSS contexts and steering traffic to them
- support XDP metadata
- make page pool allocations more NUMA aware
- Intel (100G, ice, idpf):
- extract datapath code common among Intel drivers into a library
- use fewer resources in switchdev by sharing queues with the PF
- add PFCP filter support
- add Ethernet filter support
- use a spinlock instead of HW lock in PTP clock ops
- support 5 layer Tx scheduler topology
- nVidia/Mellanox:
- 800G link modes and 100G SerDes speeds
- per-queue IRQ coalescing configuration
- Marvell Octeon:
- support offloading TC packet mark action
- Ethernet NICs consumer, embedded and virtual:
- stop lying about skb->truesize in USB Ethernet drivers, it
messes up TCP memory calculations
- Google cloud vNIC:
- support changing ring size via ethtool
- support ring reset using the queue control API
- VirtIO net:
- expose flow hash from RSS to XDP
- per-queue statistics
- add selftests
- Synopsys (stmmac):
- support controllers which require an RX clock signal from the
MII bus to perform their hardware initialization
- TI:
- icssg_prueth: support ICSSG-based Ethernet on AM65x SR1.0 devices
- icssg_prueth: add SW TX / RX Coalescing based on hrtimers
- cpsw: minimal XDP support
- Renesas (ravb):
- support describing the MDIO bus
- Realtek (r8169):
- add support for RTL8168M
- Microchip Sparx5:
- matchall and flower actions mirred and redirect
- Ethernet switches:
- nVidia/Mellanox:
- improve events processing performance
- Marvell:
- add support for MV88E6250 family internal PHYs
- Microchip:
- add DCB and DSCP mapping support for KSZ switches
- vsc73xx: convert to PHYLINK
- Realtek:
- rtl8226b/rtl8221b: add C45 instances and SerDes switching
- Many driver changes related to PHYLIB and PHYLINK deprecated API
cleanup
- Ethernet PHYs:
- Add a new driver for Airoha EN8811H 2.5 Gigabit PHY.
- micrel: lan8814: add support for PPS out and external timestamp trigger
- WiFi:
- Disable Wireless Extensions (WEXT) in all Wi-Fi 7 devices
drivers. Modern devices can only be configured using nl80211.
- mac80211/cfg80211
- handle color change per link for WiFi 7 Multi-Link Operation
- Intel (iwlwifi):
- don't support puncturing in 5 GHz
- support monitor mode on passive channels
- BZ-W device support
- P2P with HE/EHT support
- re-add support for firmware API 90
- provide channel survey information for Automatic Channel Selection
- MediaTek (mt76):
- mt7921 LED control
- mt7925 EHT radiotap support
- mt7920e PCI support
- Qualcomm (ath11k):
- P2P support for QCA6390, WCN6855 and QCA2066
- support hibernation
- ieee80211-freq-limit Device Tree property support
- Qualcomm (ath12k):
- refactoring in preparation of multi-link support
- suspend and hibernation support
- ACPI support
- debugfs support, including dfs_simulate_radar support
- RealTek:
- rtw88: RTL8723CS SDIO device support
- rtw89: RTL8922AE Wi-Fi 7 PCI device support
- rtw89: complete features of new WiFi 7 chip 8922AE including
BT-coexistence and Wake-on-WLAN
- rtw89: use BIOS ACPI settings to set TX power and channels
- rtl8xxxu: enable Management Frame Protection (MFP) support
- Bluetooth:
- support for Intel BlazarI and Filmore Peak2 (BE201)
- support for MediaTek MT7921S SDIO
- initial support for Intel PCIe BT driver
- remove HCI_AMP support"
* tag 'net-next-6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1827 commits)
selftests: netfilter: fix packetdrill conntrack testcase
net: gro: fix napi_gro_cb zeroed alignment
Bluetooth: btintel_pcie: Refactor and code cleanup
Bluetooth: btintel_pcie: Fix warning reported by sparse
Bluetooth: hci_core: Fix not handling hdev->le_num_of_adv_sets=1
Bluetooth: btintel: Fix compiler warning for multi_v7_defconfig config
Bluetooth: btintel_pcie: Fix compiler warnings
Bluetooth: btintel_pcie: Add *setup* function to download firmware
Bluetooth: btintel_pcie: Add support for PCIe transport
Bluetooth: btintel: Export few static functions
Bluetooth: HCI: Remove HCI_AMP support
Bluetooth: L2CAP: Fix div-by-zero in l2cap_le_flowctl_init()
Bluetooth: qca: Fix error code in qca_read_fw_build_info()
Bluetooth: hci_conn: Use __counted_by() and avoid -Wfamnae warning
Bluetooth: btintel: Add support for Filmore Peak2 (BE201)
Bluetooth: btintel: Add support for BlazarI
LE Create Connection command timeout increased to 20 secs
dt-bindings: net: bluetooth: Add MediaTek MT7921S SDIO Bluetooth
Bluetooth: compute LE flow credits based on recvbuf space
Bluetooth: hci_sync: Use cmd->num_cis instead of magic number
...
|
||
|
Jakub Kicinski
|
654de42f3f |
Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Merge in late fixes to prepare for the 6.10 net-next PR. Signed-off-by: Jakub Kicinski <kuba@kernel.org> |
||
|
Vadim Fedorenko
|
a2c7897795 |
ptp: ocp: fix DPLL functions
In ptp_ocp driver pin actions assume sma_nr starts with 1, but for DPLL
subsystem callback 0-based index was used. Fix it providing proper index.
Fixes:
|
||
Uwe Kleine-König
|
145473b295 |
ptp: ptp_qoriq: Convert to platform remove callback returning void
The .remove() callback for a platform driver returns an int which makes many driver authors wrongly assume it's possible to do error handling by returning an error code. However the value returned is ignored (apart from emitting a warning) and this typically results in resource leaks. To improve here there is a quest to make the remove callback return void. In the first step of this quest all drivers are converted to .remove_new(), which already returns void. Eventually after all drivers are converted, .remove_new() will be renamed to .remove(). Trivially convert this driver from always returning zero in the remove callback to the void returning variant. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Acked-by: Richard Cochran <richardcochran@gmail.com> Link: https://lore.kernel.org/r/477c6995046eee729447d4f88bf042c7577fe100.1712734365.git.u.kleine-koenig@pengutronix.de Signed-off-by: Jakub Kicinski <kuba@kernel.org> |
||
|
Uwe Kleine-König
|
cff5236946 |
ptp: ptp_ines: Convert to platform remove callback returning void
The .remove() callback for a platform driver returns an int which makes many driver authors wrongly assume it's possible to do error handling by returning an error code. However the value returned is ignored (apart from emitting a warning) and this typically results in resource leaks. To improve here there is a quest to make the remove callback return void. In the first step of this quest all drivers are converted to .remove_new(), which already returns void. Eventually after all drivers are converted, .remove_new() will be renamed to .remove(). Trivially convert this driver from always returning zero in the remove callback to the void returning variant. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Acked-by: Richard Cochran <richardcochran@gmail.com> Link: https://lore.kernel.org/r/2cc6c137dd43444abb5bdb53693713f7c2c08b71.1712734365.git.u.kleine-koenig@pengutronix.de Signed-off-by: Jakub Kicinski <kuba@kernel.org> |
||
|
Uwe Kleine-König
|
740c031861 |
ptp: ptp_idt82p33: Convert to platform remove callback returning void
The .remove() callback for a platform driver returns an int which makes many driver authors wrongly assume it's possible to do error handling by returning an error code. However the value returned is ignored (apart from emitting a warning) and this typically results in resource leaks. To improve here there is a quest to make the remove callback return void. In the first step of this quest all drivers are converted to .remove_new(), which already returns void. Eventually after all drivers are converted, .remove_new() will be renamed to .remove(). Trivially convert this driver from always returning zero in the remove callback to the void returning variant. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Acked-by: Richard Cochran <richardcochran@gmail.com> Link: https://lore.kernel.org/r/5807d0b11214b35f48908fd35cbb7b31b7655ba6.1712734365.git.u.kleine-koenig@pengutronix.de Signed-off-by: Jakub Kicinski <kuba@kernel.org> |
||
|
Uwe Kleine-König
|
5c025082f8 |
ptp: ptp_dte: Convert to platform remove callback returning void
The .remove() callback for a platform driver returns an int which makes many driver authors wrongly assume it's possible to do error handling by returning an error code. However the value returned is ignored (apart from emitting a warning) and this typically results in resource leaks. To improve here there is a quest to make the remove callback return void. In the first step of this quest all drivers are converted to .remove_new(), which already returns void. Eventually after all drivers are converted, .remove_new() will be renamed to .remove(). Trivially convert this driver from always returning zero in the remove callback to the void returning variant. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Acked-by: Richard Cochran <richardcochran@gmail.com> Link: https://lore.kernel.org/r/e8a0de7e8e6d642242350360a938132c7ba0488e.1712734365.git.u.kleine-koenig@pengutronix.de Signed-off-by: Jakub Kicinski <kuba@kernel.org> |
||
|
Uwe Kleine-König
|
32080ec2db |
ptp: ptp_clockmatrix: Convert to platform remove callback returning void
The .remove() callback for a platform driver returns an int which makes many driver authors wrongly assume it's possible to do error handling by returning an error code. However the value returned is ignored (apart from emitting a warning) and this typically results in resource leaks. To improve here there is a quest to make the remove callback return void. In the first step of this quest all drivers are converted to .remove_new(), which already returns void. Eventually after all drivers are converted, .remove_new() will be renamed to .remove(). Trivially convert this driver from always returning zero in the remove callback to the void returning variant. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Acked-by: Richard Cochran <richardcochran@gmail.com> Link: https://lore.kernel.org/r/0f0f5680c1a2a3ef19975935a2c6828a98bc4d25.1712734365.git.u.kleine-koenig@pengutronix.de Signed-off-by: Jakub Kicinski <kuba@kernel.org> |
||
Krzysztof Kozlowski
|
cd3eda2e35 |
ptp: vmw: drop owner assignment
ACPI bus core already sets the .owner, so driver does not need to. Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> |
||
|
Linus Torvalds
|
9187210eee |
Networking changes for 6.9.
Core & protocols
----------------
- Large effort by Eric to lower rtnl_lock pressure and remove locks:
- Make commonly used parts of rtnetlink (address, route dumps etc.)
lockless, protected by RCU instead of rtnl_lock.
- Add a netns exit callback which already holds rtnl_lock,
allowing netns exit to take rtnl_lock once in the core
instead of once for each driver / callback.
- Remove locks / serialization in the socket diag interface.
- Remove 6 calls to synchronize_rcu() while holding rtnl_lock.
- Remove the dev_base_lock, depend on RCU where necessary.
- Support busy polling on a per-epoll context basis. Poll length
and budget parameters can be set independently of system defaults.
- Introduce struct net_hotdata, to make sure read-mostly global config
variables fit in as few cache lines as possible.
- Add optional per-nexthop statistics to ease monitoring / debug
of ECMP imbalance problems.
- Support TCP_NOTSENT_LOWAT in MPTCP.
- Ensure that IPv6 temporary addresses' preferred lifetimes are long
enough, compared to other configured lifetimes, and at least 2 sec.
- Support forwarding of ICMP Error messages in IPSec, per RFC 4301.
- Add support for the independent control state machine for bonding
per IEEE 802.1AX-2008 5.4.15 in addition to the existing coupled
control state machine.
- Add "network ID" to MCTP socket APIs to support hosts with multiple
disjoint MCTP networks.
- Re-use the mono_delivery_time skbuff bit for packets which user
space wants to be sent at a specified time. Maintain the timing
information while traversing veth links, bridge etc.
- Take advantage of MSG_SPLICE_PAGES for RxRPC DATA and ACK packets.
- Simplify many places iterating over netdevs by using an xarray
instead of a hash table walk (hash table remains in place, for
use on fastpaths).
- Speed up scanning for expired routes by keeping a dedicated list.
- Speed up "generic" XDP by trying harder to avoid large allocations.
- Support attaching arbitrary metadata to netconsole messages.
Things we sprinkled into general kernel code
--------------------------------------------
- Enforce VM_IOREMAP flag and range in ioremap_page_range and introduce
VM_SPARSE kind and vm_area_[un]map_pages (used by bpf_arena).
- Rework selftest harness to enable the use of the full range of
ksft exit code (pass, fail, skip, xfail, xpass).
Netfilter
---------
- Allow userspace to define a table that is exclusively owned by a daemon
(via netlink socket aliveness) without auto-removing this table when
the userspace program exits. Such table gets marked as orphaned and
a restarting management daemon can re-attach/regain ownership.
- Speed up element insertions to nftables' concatenated-ranges set type.
Compact a few related data structures.
BPF
---
- Add BPF token support for delegating a subset of BPF subsystem
functionality from privileged system-wide daemons such as systemd
through special mount options for userns-bound BPF fs to a trusted
& unprivileged application.
- Introduce bpf_arena which is sparse shared memory region between BPF
program and user space where structures inside the arena can have
pointers to other areas of the arena, and pointers work seamlessly
for both user-space programs and BPF programs.
- Introduce may_goto instruction that is a contract between the verifier
and the program. The verifier allows the program to loop assuming it's
behaving well, but reserves the right to terminate it.
- Extend the BPF verifier to enable static subprog calls in spin lock
critical sections.
- Support registration of struct_ops types from modules which helps
projects like fuse-bpf that seeks to implement a new struct_ops type.
- Add support for retrieval of cookies for perf/kprobe multi links.
- Support arbitrary TCP SYN cookie generation / validation in the TC
layer with BPF to allow creating SYN flood handling in BPF firewalls.
- Add code generation to inline the bpf_kptr_xchg() helper which
improves performance when stashing/popping the allocated BPF objects.
Wireless
--------
- Add SPP (signaling and payload protected) AMSDU support.
- Support wider bandwidth OFDMA, as required for EHT operation.
Driver API
----------
- Major overhaul of the Energy Efficient Ethernet internals to support
new link modes (2.5GE, 5GE), share more code between drivers
(especially those using phylib), and encourage more uniform behavior.
Convert and clean up drivers.
- Define an API for querying per netdev queue statistics from drivers.
- IPSec: account in global stats for fully offloaded sessions.
- Create a concept of Ethernet PHY Packages at the Device Tree level,
to allow parameterizing the existing PHY package code.
- Enable Rx hashing (RSS) on GTP protocol fields.
Misc
----
- Improvements and refactoring all over networking selftests.
- Create uniform module aliases for TC classifiers, actions,
and packet schedulers to simplify creating modprobe policies.
- Address all missing MODULE_DESCRIPTION() warnings in networking.
- Extend the Netlink descriptions in YAML to cover message encapsulation
or "Netlink polymorphism", where interpretation of nested attributes
depends on link type, classifier type or some other "class type".
Drivers
-------
- Ethernet high-speed NICs:
- Add a new driver for Marvell's Octeon PCI Endpoint NIC VF.
- Intel (100G, ice, idpf):
- support E825-C devices
- nVidia/Mellanox:
- support devices with one port and multiple PCIe links
- Broadcom (bnxt):
- support n-tuple filters
- support configuring the RSS key
- Wangxun (ngbe/txgbe):
- implement irq_domain for TXGBE's sub-interrupts
- Pensando/AMD:
- support XDP
- optimize queue submission and wakeup handling (+17% bps)
- optimize struct layout, saving 28% of memory on queues
- Ethernet NICs embedded and virtual:
- Google cloud vNIC:
- refactor driver to perform memory allocations for new queue
config before stopping and freeing the old queue memory
- Synopsys (stmmac):
- obey queueMaxSDU and implement counters required by 802.1Qbv
- Renesas (ravb):
- support packet checksum offload
- suspend to RAM and runtime PM support
- Ethernet switches:
- nVidia/Mellanox:
- support for nexthop group statistics
- Microchip:
- ksz8: implement PHY loopback
- add support for KSZ8567, a 7-port 10/100Mbps switch
- PTP:
- New driver for RENESAS FemtoClock3 Wireless clock generator.
- Support OCP PTP cards designed and built by Adva.
- CAN:
- Support recvmsg() flags for own, local and remote traffic
on CAN BCM sockets.
- Support for esd GmbH PCIe/402 CAN device family.
- m_can:
- Rx/Tx submission coalescing
- wake on frame Rx
- WiFi:
- Intel (iwlwifi):
- enable signaling and payload protected A-MSDUs
- support wider-bandwidth OFDMA
- support for new devices
- bump FW API to 89 for AX devices; 90 for BZ/SC devices
- MediaTek (mt76):
- mt7915: newer ADIE version support
- mt7925: radio temperature sensor support
- Qualcomm (ath11k):
- support 6 GHz station power modes: Low Power Indoor (LPI),
Standard Power) SP and Very Low Power (VLP)
- QCA6390 & WCN6855: support 2 concurrent station interfaces
- QCA2066 support
- Qualcomm (ath12k):
- refactoring in preparation for Multi-Link Operation (MLO) support
- 1024 Block Ack window size support
- firmware-2.bin support
- support having multiple identical PCI devices (firmware needs to
have ATH12K_FW_FEATURE_MULTI_QRTR_ID)
- QCN9274: support split-PHY devices
- WCN7850: enable Power Save Mode in station mode
- WCN7850: P2P support
- RealTek:
- rtw88: support for more rtw8811cu and rtw8821cu devices
- rtw89: support SCAN_RANDOM_SN and SET_SCAN_DWELL
- rtlwifi: speed up USB firmware initialization
- rtwl8xxxu:
- RTL8188F: concurrent interface support
- Channel Switch Announcement (CSA) support in AP mode
- Broadcom (brcmfmac):
- per-vendor feature support
- per-vendor SAE password setup
- DMI nvram filename quirk for ACEPC W5 Pro
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=oY52
-----END PGP SIGNATURE-----
Merge tag 'net-next-6.9' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Core & protocols:
- Large effort by Eric to lower rtnl_lock pressure and remove locks:
- Make commonly used parts of rtnetlink (address, route dumps
etc) lockless, protected by RCU instead of rtnl_lock.
- Add a netns exit callback which already holds rtnl_lock,
allowing netns exit to take rtnl_lock once in the core instead
of once for each driver / callback.
- Remove locks / serialization in the socket diag interface.
- Remove 6 calls to synchronize_rcu() while holding rtnl_lock.
- Remove the dev_base_lock, depend on RCU where necessary.
- Support busy polling on a per-epoll context basis. Poll length and
budget parameters can be set independently of system defaults.
- Introduce struct net_hotdata, to make sure read-mostly global
config variables fit in as few cache lines as possible.
- Add optional per-nexthop statistics to ease monitoring / debug of
ECMP imbalance problems.
- Support TCP_NOTSENT_LOWAT in MPTCP.
- Ensure that IPv6 temporary addresses' preferred lifetimes are long
enough, compared to other configured lifetimes, and at least 2 sec.
- Support forwarding of ICMP Error messages in IPSec, per RFC 4301.
- Add support for the independent control state machine for bonding
per IEEE 802.1AX-2008 5.4.15 in addition to the existing coupled
control state machine.
- Add "network ID" to MCTP socket APIs to support hosts with multiple
disjoint MCTP networks.
- Re-use the mono_delivery_time skbuff bit for packets which user
space wants to be sent at a specified time. Maintain the timing
information while traversing veth links, bridge etc.
- Take advantage of MSG_SPLICE_PAGES for RxRPC DATA and ACK packets.
- Simplify many places iterating over netdevs by using an xarray
instead of a hash table walk (hash table remains in place, for use
on fastpaths).
- Speed up scanning for expired routes by keeping a dedicated list.
- Speed up "generic" XDP by trying harder to avoid large allocations.
- Support attaching arbitrary metadata to netconsole messages.
Things we sprinkled into general kernel code:
- Enforce VM_IOREMAP flag and range in ioremap_page_range and
introduce VM_SPARSE kind and vm_area_[un]map_pages (used by
bpf_arena).
- Rework selftest harness to enable the use of the full range of ksft
exit code (pass, fail, skip, xfail, xpass).
Netfilter:
- Allow userspace to define a table that is exclusively owned by a
daemon (via netlink socket aliveness) without auto-removing this
table when the userspace program exits. Such table gets marked as
orphaned and a restarting management daemon can re-attach/regain
ownership.
- Speed up element insertions to nftables' concatenated-ranges set
type. Compact a few related data structures.
BPF:
- Add BPF token support for delegating a subset of BPF subsystem
functionality from privileged system-wide daemons such as systemd
through special mount options for userns-bound BPF fs to a trusted
& unprivileged application.
- Introduce bpf_arena which is sparse shared memory region between
BPF program and user space where structures inside the arena can
have pointers to other areas of the arena, and pointers work
seamlessly for both user-space programs and BPF programs.
- Introduce may_goto instruction that is a contract between the
verifier and the program. The verifier allows the program to loop
assuming it's behaving well, but reserves the right to terminate
it.
- Extend the BPF verifier to enable static subprog calls in spin lock
critical sections.
- Support registration of struct_ops types from modules which helps
projects like fuse-bpf that seeks to implement a new struct_ops
type.
- Add support for retrieval of cookies for perf/kprobe multi links.
- Support arbitrary TCP SYN cookie generation / validation in the TC
layer with BPF to allow creating SYN flood handling in BPF
firewalls.
- Add code generation to inline the bpf_kptr_xchg() helper which
improves performance when stashing/popping the allocated BPF
objects.
Wireless:
- Add SPP (signaling and payload protected) AMSDU support.
- Support wider bandwidth OFDMA, as required for EHT operation.
Driver API:
- Major overhaul of the Energy Efficient Ethernet internals to
support new link modes (2.5GE, 5GE), share more code between
drivers (especially those using phylib), and encourage more
uniform behavior. Convert and clean up drivers.
- Define an API for querying per netdev queue statistics from
drivers.
- IPSec: account in global stats for fully offloaded sessions.
- Create a concept of Ethernet PHY Packages at the Device Tree level,
to allow parameterizing the existing PHY package code.
- Enable Rx hashing (RSS) on GTP protocol fields.
Misc:
- Improvements and refactoring all over networking selftests.
- Create uniform module aliases for TC classifiers, actions, and
packet schedulers to simplify creating modprobe policies.
- Address all missing MODULE_DESCRIPTION() warnings in networking.
- Extend the Netlink descriptions in YAML to cover message
encapsulation or "Netlink polymorphism", where interpretation of
nested attributes depends on link type, classifier type or some
other "class type".
Drivers:
- Ethernet high-speed NICs:
- Add a new driver for Marvell's Octeon PCI Endpoint NIC VF.
- Intel (100G, ice, idpf):
- support E825-C devices
- nVidia/Mellanox:
- support devices with one port and multiple PCIe links
- Broadcom (bnxt):
- support n-tuple filters
- support configuring the RSS key
- Wangxun (ngbe/txgbe):
- implement irq_domain for TXGBE's sub-interrupts
- Pensando/AMD:
- support XDP
- optimize queue submission and wakeup handling (+17% bps)
- optimize struct layout, saving 28% of memory on queues
- Ethernet NICs embedded and virtual:
- Google cloud vNIC:
- refactor driver to perform memory allocations for new queue
config before stopping and freeing the old queue memory
- Synopsys (stmmac):
- obey queueMaxSDU and implement counters required by 802.1Qbv
- Renesas (ravb):
- support packet checksum offload
- suspend to RAM and runtime PM support
- Ethernet switches:
- nVidia/Mellanox:
- support for nexthop group statistics
- Microchip:
- ksz8: implement PHY loopback
- add support for KSZ8567, a 7-port 10/100Mbps switch
- PTP:
- New driver for RENESAS FemtoClock3 Wireless clock generator.
- Support OCP PTP cards designed and built by Adva.
- CAN:
- Support recvmsg() flags for own, local and remote traffic on CAN
BCM sockets.
- Support for esd GmbH PCIe/402 CAN device family.
- m_can:
- Rx/Tx submission coalescing
- wake on frame Rx
- WiFi:
- Intel (iwlwifi):
- enable signaling and payload protected A-MSDUs
- support wider-bandwidth OFDMA
- support for new devices
- bump FW API to 89 for AX devices; 90 for BZ/SC devices
- MediaTek (mt76):
- mt7915: newer ADIE version support
- mt7925: radio temperature sensor support
- Qualcomm (ath11k):
- support 6 GHz station power modes: Low Power Indoor (LPI),
Standard Power) SP and Very Low Power (VLP)
- QCA6390 & WCN6855: support 2 concurrent station interfaces
- QCA2066 support
- Qualcomm (ath12k):
- refactoring in preparation for Multi-Link Operation (MLO)
support
- 1024 Block Ack window size support
- firmware-2.bin support
- support having multiple identical PCI devices (firmware needs
to have ATH12K_FW_FEATURE_MULTI_QRTR_ID)
- QCN9274: support split-PHY devices
- WCN7850: enable Power Save Mode in station mode
- WCN7850: P2P support
- RealTek:
- rtw88: support for more rtw8811cu and rtw8821cu devices
- rtw89: support SCAN_RANDOM_SN and SET_SCAN_DWELL
- rtlwifi: speed up USB firmware initialization
- rtwl8xxxu:
- RTL8188F: concurrent interface support
- Channel Switch Announcement (CSA) support in AP mode
- Broadcom (brcmfmac):
- per-vendor feature support
- per-vendor SAE password setup
- DMI nvram filename quirk for ACEPC W5 Pro"
* tag 'net-next-6.9' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2255 commits)
nexthop: Fix splat with CONFIG_DEBUG_PREEMPT=y
nexthop: Fix out-of-bounds access during attribute validation
nexthop: Only parse NHA_OP_FLAGS for dump messages that require it
nexthop: Only parse NHA_OP_FLAGS for get messages that require it
bpf: move sleepable flag from bpf_prog_aux to bpf_prog
bpf: hardcode BPF_PROG_PACK_SIZE to 2MB * num_possible_nodes()
selftests/bpf: Add kprobe multi triggering benchmarks
ptp: Move from simple ida to xarray
vxlan: Remove generic .ndo_get_stats64
vxlan: Do not alloc tstats manually
devlink: Add comments to use netlink gen tool
nfp: flower: handle acti_netdevs allocation failure
net/packet: Add getsockopt support for PACKET_COPY_THRESH
net/netlink: Add getsockopt support for NETLINK_LISTEN_ALL_NSID
selftests/bpf: Add bpf_arena_htab test.
selftests/bpf: Add bpf_arena_list test.
selftests/bpf: Add unit tests for bpf_arena_alloc/free_pages
bpf: Add helper macro bpf_addr_space_cast()
libbpf: Recognize __arena global variables.
bpftool: Recognize arena map type
...
|
||
|
Kory Maincent
|
f095fefacd |
ptp: Move from simple ida to xarray
Move from simple ida to xarray for storing and loading the ptp_clock pointer. This prepares support for future hardware timestamp selection by being able to link the ptp clock index to its pointer. Signed-off-by: Kory Maincent <kory.maincent@bootlin.com> Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Link: https://lore.kernel.org/r/20240311144730.1239594-1-kory.maincent@bootlin.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> |
||
Ricardo B. Marliere
|
c057eddcb4 |
ptp: make ptp_class constant
Since commit
|
||
|
Uwe Kleine-König
|
60d06425e0 |
ptp: fc3: Convert to platform remove callback returning void
The .remove() callback for a platform driver returns an int which makes many driver authors wrongly assume it's possible to do error handling by returning an error code. However the value returned is ignored (apart from emitting a warning) and this typically results in resource leaks. To improve here there is a quest to make the remove callback return void. In the first step of this quest all drivers are converted to .remove_new(), which already returns void. Eventually after all drivers are converted, .remove_new() will be renamed to .remove(). Trivially convert this driver from always returning zero in the remove callback to the void returning variant. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://lore.kernel.org/r/20240304091325.717546-2-u.kleine-koenig@pengutronix.de Signed-off-by: Jakub Kicinski <kuba@kernel.org> |
||
Sagi Maimon
|
ef61f5528f |
ptp: ocp: add Adva timecard support
Adding support for the Adva timecard. The card uses different drivers to provide access to the firmware SPI flash (Altera based). Other parts of the code are the same and could be reused. Signed-off-by: Sagi Maimon <maimon.sagi@gmail.com> Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev> Link: https://lore.kernel.org/r/20240205153046.3642-1-maimon.sagi@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> |
||
Peter Hilber
|
b152688c91 |
treewide: Remove system_counterval_t.cs, which is never read
The clocksource pointer in struct system_counterval_t is not evaluated any more. Remove the code setting the member, and the member itself. Signed-off-by: Peter Hilber <peter.hilber@opensynergy.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Link: https://lore.kernel.org/r/20240201010453.2212371-8-peter.hilber@opensynergy.com |
||
|
Peter Hilber
|
9be3b2f057 |
ptp/kvm, arm_arch_timer: Set system_counterval_t.cs_id to constant
Identify the clocksources used by ptp_kvm by setting the clocksource ID enum constants. This avoids dereferencing struct clocksource. Once the system_counterval_t.cs member will be removed, this will also avoid the need to obtain clocksource pointers from kvm_arch_ptp_get_crosststamp(). The clocksource IDs are associated to timestamps requested from the KVM hypervisor, so the proper clocksource ID is known at the ptp_kvm request site. While at it, also make the ptp_kvm_get_time_fn() 'ret' variable type int as that's what the function return value is. Signed-off-by: Peter Hilber <peter.hilber@opensynergy.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Link: https://lore.kernel.org/r/20240201010453.2212371-6-peter.hilber@opensynergy.com |
||
|
Peter Hilber
|
576bd4962f |
x86/kvm, ptp/kvm: Add clocksource ID, set system_counterval_t.cs_id
Add a clocksource ID for the x86 kvmclock. Also, for ptp_kvm, set the recently added struct system_counterval_t member cs_id to the clocksource ID (x86 kvmclock or ARM Generic Timer). In the future, get_device_system_crosststamp() will compare the clocksource ID in struct system_counterval_t, rather than the clocksource. For now, to avoid touching too many subsystems at once, extract the clocksource ID from the clocksource. The clocksource dereference will be removed once everything is converted over.. Signed-off-by: Peter Hilber <peter.hilber@opensynergy.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Link: https://lore.kernel.org/r/20240201010453.2212371-5-peter.hilber@opensynergy.com |
||
Jiri Pirko
|
e2ca9e7584 |
dpll: extend lock_status_get() op by status error and expose to user
Pass additional argunent status_error over lock_status_get() so drivers can fill it up. In case they do, expose the value over previously introduced attribute to user. Do it only in case the current lock_status is either "unlocked" or "holdover". Signed-off-by: Jiri Pirko <jiri@nvidia.com> Acked-by: Vadim Fedorenko <vadim.fedorenko@linux.dev> Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: Paolo Abeni <pabeni@redhat.com> |
||
Min Li
|
1ddfecafab |
ptp: add FemtoClock3 Wireless as ptp hardware clock
The RENESAS FemtoClock3 Wireless is a high-performance jitter attenuator, frequency translator, and clock synthesizer. The device is comprised of 3 digital PLLs (DPLL) to track CLKIN inputs and three independent low phase noise fractional output dividers (FOD) that output low phase noise clocks. FemtoClock3 supports one Time Synchronization (Time Sync) channel to enable an external processor to control the phase and frequency of the Time Sync channel and to take phase measurements using the TDC. Intended applications are synchronization using the precision time protocol (PTP) and synchronization with 0.5 Hz and 1 Hz signals from GNSS. Signed-off-by: Min Li <min.li.xe@renesas.com> Acked-by: Lee Jones <lee@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> |
||
|
Min Li
|
ea1cc3ee34 |
ptp: introduce PTP_CLOCK_EXTOFF event for the measured external offset
This change is for the PHC devices that can measure the phase offset between PHC signal and the external signal, such as the 1PPS signal of GNSS. Reporting PTP_CLOCK_EXTOFF to user space will be piggy-backed to the existing ptp_extts_event so that application such as ts2phc can poll the external offset the same way as extts. Hence, ts2phc can use the offset to achieve the alignment between PHC and the external signal by the help of either SW or HW filters. Signed-off-by: Min Li <min.li.xe@renesas.com> Acked-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> |
||
Li Zhijian
|
8d0293302d |
drivers/ptp: Convert snprintf to sysfs_emit
Per filesystems/sysfs.rst, show() should only use sysfs_emit() or sysfs_emit_at() when formatting the value to be returned to user space. coccinelle complains that there are still a couple of functions that use snprintf(). Convert them to sysfs_emit(). > ./drivers/ptp/ptp_sysfs.c:27:8-16: WARNING: please use sysfs_emit No functional change intended Signed-off-by: Li Zhijian <lizhijian@fujitsu.com> Acked-by: Richard Cochran <richardcochran@gmail.com> Link: https://lore.kernel.org/r/20240125015329.123023-1-lizhijian@fujitsu.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> |
||
|
Jakub Kicinski
|
e63c1822ac |
Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Cross-merge networking fixes after downstream PR. Conflicts: drivers/net/ethernet/broadcom/bnxt/bnxt.c |
||
Andy Shevchenko
|
07938d774f |
ptp: ocp: Use DEFINE_RES_*() in place
There is no need to have an intermediate functions as DEFINE_RES_*() macros are represented by compound literals. Just use them in place. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev> Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> |
||
|
Sagi Maimon
|
97417cd79c |
ptp: ocp: fix bug in unregistering the DPLL subsystem
When unregistering the DPLL subsystem the priv pointer is different then
the one used for registration which cause failure in unregistering.
Fixes:
|
||
|
Jiri Pirko
|
4f7aa122bc |
dpll: remove leftover mode_supported() op and use mode_get() instead
Mode supported is currently reported to the user exactly the same, as the current mode. That's because mode changing is not implemented. Remove the leftover mode_supported() op and use mode_get() to fill up the supported mode exposed to user. One, if even, mode changing is going to be introduced, this could be very easily taken back. In the meantime, prevent drivers form implementing this in wrong way (as for example recent netdevsim implementation attempt intended to do). Signed-off-by: Jiri Pirko <jiri@nvidia.com> Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> |
||
|
Kory Maincent
|
446e230582 |
net: Convert PHYs hwtstamp callback to use kernel_hwtstamp_config
The PHYs hwtstamp callback are still getting the timestamp config from ifreq and using copy_from/to_user. Get rid of these functions by using timestamp configuration in parameter. This also allow to move on to kernel_hwtstamp_config and be similar to net devices using the new ndo_hwstamp_get/set. This adds the possibility to manipulate the timestamp configuration from the kernel which was not possible with the copy_from/to_user. Signed-off-by: Kory Maincent <kory.maincent@bootlin.com> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> |
||
Eric Dumazet
|
73bde5a329 |
ptp: annotate data-race around q->head and q->tail
As I was working on a syzbot report, I found that KCSAN would
probably complain that reading q->head or q->tail without
barriers could lead to invalid results.
Add corresponding READ_ONCE() and WRITE_ONCE() to avoid
load-store tearing.
Fixes:
|
||
|
Jakub Kicinski
|
4b3812d90b |
Revert "ptp: Fixes a null pointer dereference in ptp_ioctl"
This reverts commit |
||
Yuran Pereira
|
8a4f030dbc |
ptp: Fixes a null pointer dereference in ptp_ioctl
Syzkaller found a null pointer dereference in ptp_ioctl
originating from the lack of a null check for tsevq.
```
general protection fault, probably for non-canonical
address 0xdffffc000000020b: 0000 [#1] PREEMPT SMP KASAN
KASAN: probably user-memory-access in range
[0x0000000000001058-0x000000000000105f]
CPU: 0 PID: 5053 Comm: syz-executor353 Not tainted
6.6.0-syzkaller-10396-g4652b8e4f3ff #0
Hardware name: Google Google Compute Engine/Google Compute Engine,
BIOS Google 10/09/2023
RIP: 0010:ptp_ioctl+0xcb7/0x1d10 drivers/ptp/ptp_chardev.c:476
...
Call Trace:
<TASK>
posix_clock_ioctl+0xf8/0x160 kernel/time/posix-clock.c:86
vfs_ioctl fs/ioctl.c:51 [inline]
__do_sys_ioctl fs/ioctl.c:871 [inline]
__se_sys_ioctl fs/ioctl.c:857 [inline]
__x64_sys_ioctl+0x18f/0x210 fs/ioctl.c:857
do_syscall_x64 arch/x86/entry/common.c:51 [inline]
do_syscall_64+0x3f/0x110 arch/x86/entry/common.c:82
entry_SYSCALL_64_after_hwframe+0x63/0x6b
```
This patch fixes the issue by adding a check for tsevq and
ensuring ptp_ioctl returns with an error if tsevq is null.
Reported-by: syzbot+8a78ecea7ac1a2ea26e5@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=8a78ecea7ac1a2ea26e5
Fixes:
|
||
Edward Adam Davis
|
1bea2c3e6d |
ptp: fix corrupted list in ptp_open
There is no lock protection when writing ptp->tsevqs in ptp_open() and
ptp_release(), which can cause data corruption, use spin lock to avoid this
issue.
Moreover, ptp_release() should not be used to release the queue in ptp_read(),
and it should be deleted altogether.
Acked-by: Richard Cochran <richardcochran@gmail.com>
Reported-and-tested-by: syzbot+df3f3ef31f60781fa911@syzkaller.appspotmail.com
Fixes:
|
||
|
Edward Adam Davis
|
b714ca2ccf |
ptp: ptp_read should not release queue
Firstly, queue is not the memory allocated in ptp_read;
Secondly, other processes may block at ptp_read and wait for conditions to be
met to perform read operations.
Acked-by: Richard Cochran <richardcochran@gmail.com>
Reported-and-tested-by: syzbot+df3f3ef31f60781fa911@syzkaller.appspotmail.com
Fixes:
|
||
|
Dan Carpenter
|
75a384ceda |
ptp: prevent string overflow
The ida_alloc_max() function can return up to INT_MAX so this buffer is
not large enough. Also use snprintf() for extra safety.
Fixes:
|
||
Xabier Marquiegui
|
403376ddb4 |
ptp: add debugfs interface to see applied channel masks
Use debugfs to be able to view channel mask applied to every timestamp event queue. Every time the device is opened, a new entry is created in `$DEBUGFS_MOUNTPOINT/ptpN/$INSTANCE_ADDRESS/mask`. The mask value can be viewed grouped in 32bit decimal values using cat, or converted to hexadecimal with the included `ptpchmaskfmt.sh` script. 32 bit values are listed from least significant to most significant. Signed-off-by: Xabier Marquiegui <reibax@gmail.com> Suggested-by: Vinicius Costa Gomes <vinicius.gomes@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> |
||
|
Xabier Marquiegui
|
c5a445b1e9 |
ptp: support event queue reader channel masks
On systems with multiple timestamp event channels, some readers might want to receive only a subset of those channels. Add the necessary modifications to support timestamp event channel filtering, including two IOCTL operations: - Clear all channels - Enable one channel The mask modification operations will be applied exclusively on the event queue assigned to the file descriptor used on the IOCTL operation, so the typical procedure to have a reader receiving only a subset of the enabled channels would be: - Open device file - ioctl: clear all channels - ioctl: enable one channel - start reading Calling the enable one channel ioctl more than once will result in multiple enabled channels. Signed-off-by: Xabier Marquiegui <reibax@gmail.com> Suggested-by: Richard Cochran <richardcochran@gmail.com> Suggested-by: Vinicius Costa Gomes <vinicius.gomes@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> |
||
|
Xabier Marquiegui
|
8f5de6fb24 |
ptp: support multiple timestamp event readers
Use linked lists to create one event queue per open file. This enables simultaneous readers for timestamp event queues. Signed-off-by: Xabier Marquiegui <reibax@gmail.com> Suggested-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> |
||
|
Xabier Marquiegui
|
d26ab5a35a |
ptp: Replace timestamp event queue with linked list
Introduce linked lists to access the timestamp event queue. Signed-off-by: Xabier Marquiegui <reibax@gmail.com> Suggested-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> |
||
|
Xabier Marquiegui
|
60c6946675 |
posix-clock: introduce posix_clock_context concept
Add the necessary structure to support custom private-data per posix-clock user. The previous implementation of posix-clock assumed all file open instances need access to the same clock structure on private_data. The need for individual data structures per file open instance has been identified when developing support for multiple timestamp event queue users for ptp_clock. Signed-off-by: Xabier Marquiegui <reibax@gmail.com> Suggested-by: Richard Cochran <richardcochran@gmail.com> Suggested-by: Vinicius Costa Gomes <vinicius.gomes@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> |
||
|
Jakub Kicinski
|
2606cf059c |
Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Cross-merge networking fixes after downstream PR. No conflicts (or adjacent changes of note). Signed-off-by: Jakub Kicinski <kuba@kernel.org> |