Currently, all harts have to jump Linux in RISC-V. This complicates the
multi-stage boot process as every transient stage also has to ensure all
harts enter to that stage and jump to Linux afterwards. It also obstructs
a clean Kexec implementation.
SBI HSM extension provides alternate solutions where only a single hart
need to boot and enter Linux. The booting hart can bring up secondary
harts one by one afterwards.
Add SBI HSM based cpu_ops that implements an ordered booting method in
RISC-V. This change is also backward compatible with older firmware not
implementing HSM extension. If a latest kernel is used with older
firmware, it will continue to use the default spinning booting method.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
All SBI related extensions will not be implemented in sbi.c to avoid
bloating. Thus, sbi_err_map_linux_errno() will be used in other files
implementing that specific extension.
Export the function so that it can be used later.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Currently, all non-booting harts start booting after the booting hart
updates the per-hart stack pointer. This is done in a way that, it's
difficult to implement any other booting method without breaking the
backward compatibility.
Define a cpu_ops method that allows to introduce other booting methods
in future. Modify the current booting method to be compatible with
cpu_ops.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
The secondary hart booting and relocation code are under .init section.
As a result, it will be freed once kernel booting is done. However,
ordered booting protocol and CPU hotplug always requires these functions
to be present to bringup harts after initial kernel boot.
Move the required functions to a different section and make sure that
they are in memory within first 2MB offset as trampoline page directory
only maps first 2MB.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Few v0.1 SBI calls are being replaced by new SBI calls that follows v0.2
calling convention.
Implement the replacement extensions and few additional new SBI function calls
that makes way for a better SBI interface in future.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
We now have SBI v0.2 which is more scalable and extendable to handle
future needs for RISC-V supervisor interfaces.
Introduce a new config and move all SBI v0.1 code under that config.
This allows to implement the new replacement SBI extensions cleanly
and remove v0.1 extensions easily in future. Currently, the config
is enabled by default. Once all M-mode software, with v0.1, is no
longer in use, this config option and all relevant code can be easily
removed.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
The SBI v0.2 introduces a base extension which is backward compatible
with v0.1. Implement all helper functions and minimum required SBI
calls from v0.2 for now. All other base extension function will be
added later as per need.
As v0.2 calling convention is backward compatible with v0.1, remove
the v0.1 helper functions and just use v0.2 calling convention.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Palmer Dabbelt <palmerdabbelt@google.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Treewide:
- Cleanup of setup_irq() which is not longer required because the
memory allocator is available early. Most cleanup changes come
through the various maintainer trees, so the final removal of
setup_irq() is postponed towards the end of the merge window.
Core:
- Protection against unsafe invocation of interrupt handlers and unsafe
interrupt injection including a fixup of the offending PCI/AER error
injection mechanism.
Invoking interrupt handlers from arbitrary contexts, i.e. outside of
an actual interrupt, can cause inconsistent state on the fragile
x86 interrupt affinity changing hardware trainwreck.
Drivers:
- Second wave of support for the new ARM GICv4.1
- Multi-instance support for Xilinx and PLIC interrupt controllers
- CPU-Hotplug support for PLIC
- The obligatory new driver for X1000 TCU
- Enhancements, cleanups and fixes all over the place
-----BEGIN PGP SIGNATURE-----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=DZ/G
-----END PGP SIGNATURE-----
Merge tag 'irq-core-2020-03-30' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq updates from Thomas Gleixner:
"Updates for the interrupt subsystem:
Treewide:
- Cleanup of setup_irq() which is not longer required because the
memory allocator is available early.
Most cleanup changes come through the various maintainer trees, so
the final removal of setup_irq() is postponed towards the end of
the merge window.
Core:
- Protection against unsafe invocation of interrupt handlers and
unsafe interrupt injection including a fixup of the offending
PCI/AER error injection mechanism.
Invoking interrupt handlers from arbitrary contexts, i.e. outside
of an actual interrupt, can cause inconsistent state on the
fragile x86 interrupt affinity changing hardware trainwreck.
Drivers:
- Second wave of support for the new ARM GICv4.1
- Multi-instance support for Xilinx and PLIC interrupt controllers
- CPU-Hotplug support for PLIC
- The obligatory new driver for X1000 TCU
- Enhancements, cleanups and fixes all over the place"
* tag 'irq-core-2020-03-30' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (58 commits)
unicore32: Replace setup_irq() by request_irq()
sh: Replace setup_irq() by request_irq()
hexagon: Replace setup_irq() by request_irq()
c6x: Replace setup_irq() by request_irq()
alpha: Replace setup_irq() by request_irq()
irqchip/gic-v4.1: Eagerly vmap vPEs
irqchip/gic-v4.1: Add VSGI property setup
irqchip/gic-v4.1: Add VSGI allocation/teardown
irqchip/gic-v4.1: Move doorbell management to the GICv4 abstraction layer
irqchip/gic-v4.1: Plumb set_vcpu_affinity SGI callbacks
irqchip/gic-v4.1: Plumb get/set_irqchip_state SGI callbacks
irqchip/gic-v4.1: Plumb mask/unmask SGI callbacks
irqchip/gic-v4.1: Add initial SGI configuration
irqchip/gic-v4.1: Plumb skeletal VSGI irqchip
irqchip/stm32: Retrigger both in eoi and unmask callbacks
irqchip/gic-v3: Move irq_domain_update_bus_token to after checking for NULL domain
irqchip/xilinx: Do not call irq_set_default_host()
irqchip/xilinx: Enable generic irq multi handler
irqchip/xilinx: Fill error code when irq domain registration fails
irqchip/xilinx: Add support for multiple instances
...
On strict kernel memory permission, the ftrace have to change the
permission of text for dynamic patching the intructions. Use
riscv_patch_text_nosync() to patch code instead of probe_kernel_write.
Signed-off-by: Zong Li <zong.li@sifive.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
On strict kernel memory permission, we couldn't patch code without
writable permission. Preserve two holes in fixmap area, so we can map
the kernel code temporarily to fixmap area, then patch the instructions.
We need two pages here because we support the compressed instruction, so
the instruction might be align to 2 bytes. When patching the 32-bit
length instruction which is 2 bytes alignment, it will across two pages.
Introduce two interfaces to patch kernel code:
riscv_patch_text_nosync:
- patch code without synchronization, it's caller's responsibility to
synchronize all CPUs if needed.
riscv_patch_text:
- patch code and always synchronize with stop_machine()
Signed-off-by: Zong Li <zong.li@sifive.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Extract the calculation of instruction length for common use.
Signed-off-by: Zong Li <zong.li@sifive.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
The kernel mapping will tried to optimize its mapping by using bigger
size. In rv64, it tries to use PMD_SIZE, and tryies to use PGDIR_SIZE in
rv32. To ensure that the start address of these sections could fit the
mapping entry size, make them align to the biggest alignment.
Define a macro SECTION_ALIGN because the HPAGE_SIZE or PMD_SIZE, etc.,
are invisible in linker script.
This patch is prepared for STRICT_KERNEL_RWX support.
Signed-off-by: Zong Li <zong.li@sifive.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Move EXCEPTION_TABLE immediately after RO_DATA. Make it easy to set the
attribution of the sections which should be read-only at a time.
Add _data to specify the start of data section with write permission.
This patch is prepared for STRICT_KERNEL_RWX support.
Signed-off-by: Zong Li <zong.li@sifive.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
This patch fixes the IPI(inner processor interrupt) missing issue. It
failed because it used hartid_mask to iterate for_each_cpu(), however the
cpu_mask and hartid_mask may not be always the same. It will never send the
IPI to hartid 4 because it will be skipped in for_each_cpu loop in my case.
We can reproduce this case in Qemu sifive_u machine by this command.
qemu-system-riscv64 -nographic -smp 5 -m 1G -M sifive_u -kernel \
arch/riscv/boot/loader
It will hang in csd_lock_wait(csd) because the csd_unlock(csd) is not
called. It is not called because hartid 4 doesn't receive the IPI to
release this lock. The caller hart doesn't send the IPI to hartid 4 is
because of hartid 4 is skipped in for_each_cpu(). It will be skipped is
because "(cpu) < nr_cpu_ids" is not true. The hartid is 4 and nr_cpu_ids
is 4. Therefore it should use cpumask in for_each_cpu() instead of
hartid_mask.
/* Send a message to all CPUs in the map */
arch_send_call_function_ipi_mask(cfd->cpumask_ipi);
if (wait) {
for_each_cpu(cpu, cfd->cpumask) {
call_single_data_t *csd;
csd = per_cpu_ptr(cfd->csd, cpu);
csd_lock_wait(csd);
}
}
for ((cpu) = -1; \
(cpu) = cpumask_next((cpu), (mask)), \
(cpu) < nr_cpu_ids;)
It could boot to login console after this patch applied.
Fixes: b2d36b5668f6 ("riscv: provide native clint access for M-mode")
Signed-off-by: Greentime Hu <greentime.hu@sifive.com>
Reviewed-by: Palmer Dabbelt <palmerdabbelt@google.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Currently, PLIC threshold is only initialized once in the beginning.
However, threshold can be set to disabled if a CPU is marked offline with
CPU hotplug feature. This will not allow to change the irq affinity to a
CPU that just came online.
Add PLIC specific CPU hotplug callbacks and enable the threshold when a CPU
comes online. Take this opportunity to move the external interrupt enable
code from trap init to PLIC driver as well. On cpu offline path, the driver
performs the exact opposite operations i.e. disable the interrupt and
the threshold.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Anup Patel <anup@brainfault.org>
Link: https://lore.kernel.org/r/20200302231146.15530-2-atish.patra@wdc.com
If secure_computing() rejected a system call, we were previously setting
the system call number to -1, to indicate to later code that the syscall
failed. However, if something (e.g. a user notification) was sleeping, and
received a signal, we may set a0 to -ERESTARTSYS and re-try the system call
again.
In this case, seccomp "denies" the syscall (because of the signal), and we
would set a7 to -1, thus losing the value of the system call we want to
restart.
Instead, let's return -1 from do_syscall_trace_enter() to indicate that the
syscall was rejected, so we don't clobber the value in case of -ERESTARTSYS
or whatever.
This commit fixes the user_notification_signal seccomp selftest on riscv to
no longer hang. That test expects the system call to be re-issued after the
signal, and it wasn't due to the above bug. Now that it is, everything
works normally.
Note that in the ptrace (tracer) case, the tracer can set the register
values to whatever they want, so we still need to keep the code that
handles out-of-bounds syscalls. However, we can drop the comment.
We can also drop syscall_set_nr(), since it is no longer used anywhere, and
the code that re-loads the value in a7 because of it.
Reported in: https://lore.kernel.org/bpf/CAEn-LTp=ss0Dfv6J00=rCAy+N78U2AmhqJNjfqjr2FDpPYjxEQ@mail.gmail.com/
Reported-by: David Abdurachmanov <david.abdurachmanov@gmail.com>
Signed-off-by: Tycho Andersen <tycho@tycho.ws>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
These are only used once, and when reading the code I've always found them to
be more of a headache than a benefit. While they were never worth removing
before, LLVM's integrated assembler doesn't support LOCAL so rather that trying
to figure out how to refactor the macros it seems saner to just inline them.
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
GCC allows users to hint to the register allocation that a variable should be
placed in a register by using a syntax along the lines of
function(...) {
register long in_REG __asm__("REG");
}
We've abused this a bit throughout the RISC-V port to access fixed registers
directly as C variables. In practice it's never going to blow up because GCC
isn't going to allocate these registers, but it's not a well defined syntax so
we really shouldn't be relying upon this. Luckily there is a very similar but
well defined syntax that allows us to still access these registers directly as
C variables, which is to simply declare the register variables globally. For
fixed variables this doesn't change the ABI.
LLVM disallows this ambiguous syntax, so this isn't just strictly a formatting
change.
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
I don't know why we were doing this, as it's been there since the beginning.
After d841f729e655 ("riscv: force hart_lottery to put in .sdata section") my
guess would be that it made the kernel boot and we forgot to fix it more
cleanly.
The default .bss segment already contains the .sbss section, so we don't need
to do anything additional to ensure the symbols in .sbss continue to work.
Tested-by: Zong Li <zong.li@sifive.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
In PIC code model, the zero initialized data always be put in .bss
section, so when building kernel as PIE, the hart_lottery won't present
in small data section, and it causes more than one harts to get the
lottery, because the main hart clears the content of .bss section
immediately after it getting the lottery.
Signed-off-by: Zong Li <zong.li@sifive.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
[Palmer: added a comment]
Reviewed-by: Palmer Dabbelt <palmerdabbelt@google.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
The compiler uses the PIC-relative method to access static variables
instead of GOT when the code model is PIC. Therefore, the limitation of
the access range from the instruction to the symbol address is +-2GB.
Under this circumstance, the kernel cannot load a kernel module if this
module has static per-CPU symbols declared by DEFINE_PER_CPU(). The reason
is that kernel relocates the .data..percpu section of the kernel module to
the end of kernel's .data..percpu. Hence, the distance between the per-CPU
symbols and the instruction will exceed the 2GB limits. To solve this
problem, the kernel should place the loaded module in the memory area
[&_end-2G, VMALLOC_END].
Signed-off-by: Vincent Chen <vincent.chen@sifive.com>
Suggested-by: Alexandre Ghiti <alex@ghiti.fr>
Suggested-by: Anup Patel <anup@brainfault.org>
Tested-by: Alexandre Ghiti <alex@ghiti.fr>
Tested-by: Carlos de Paula <me@carlosedp.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Historically, we have been enabling all interrupts for each
HART in trap_init(). Ideally, we should only enable M-mode
interrupts for M-mode kernel and S-mode interrupts for S-mode
kernel in trap_init().
Currently, we get suprious S-mode interrupts on Kendryte K210
board running M-mode NO-MMU kernel because we are enabling all
interrupts in trap_init(). To fix this, we only enable software
and external interrupt in trap_init(). In future, trap_init()
will only enable software interrupt and PLIC driver will enable
external interrupt using CPU notifiers.
Fixes: a4c3733d32 ("riscv: abstract out CSR names for supervisor vs machine mode")
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
Tested-by: Palmer Dabbelt <palmerdabbelt@google.com> [QMEU virt machine with SMP]
[Palmer: Move the Fixes up to a newer commit]
Reviewed-by: Palmer Dabbelt <palmerdabbelt@google.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
When the kernel is running in S-mode, the expectation is that the
bootloader or SBI layer will configure the PMP to allow the kernel to
access physical memory. But, when the kernel is running in M-mode and is
started with the ELF "loader", there's probably no bootloader or SBI layer
involved to configure the PMP. Thus, we need to configure the PMP
ourselves to enable the kernel to access all regions.
Signed-off-by: Greentime Hu <greentime.hu@sifive.com>
Reviewed-by: Palmer Dabbelt <palmerdabbelt@google.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
This tag contains a handful of patches that I'd like to target for this merge
window:
* Support for kasan.
* 32-bit physical addresses on rv32i-based systems.
* Support for CONFIG_DEBUG_VIRTUAL
* DT entry for the FU540 GPIO controller, which has recently had a device
driver merged.
These boot a buildroot-based system on QEMU's virt board for me.
-----BEGIN PGP SIGNATURE-----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=W7f7
-----END PGP SIGNATURE-----
Merge tag 'riscv-for-linus-5.6-mw0' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V updates from Palmer Dabbelt:
"This contains a handful of patches for this merge window:
- Support for kasan
- 32-bit physical addresses on rv32i-based systems
- Support for CONFIG_DEBUG_VIRTUAL
- DT entry for the FU540 GPIO controller, which has recently had a
device driver merged
These boot a buildroot-based system on QEMU's virt board for me"
* tag 'riscv-for-linus-5.6-mw0' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: dts: Add DT support for SiFive FU540 GPIO driver
riscv: mm: add support for CONFIG_DEBUG_VIRTUAL
riscv: keep 32-bit kernel to 32-bit phys_addr_t
kasan: Add riscv to KASAN documentation.
riscv: Add KASAN support
kasan: No KASAN's memmove check if archs don't have it.
Here are the big set of tty and serial driver updates for 5.6-rc1
Included in here are:
- dummy_con cleanups (touches lots of arch code)
- sysrq logic cleanups (touches lots of serial drivers)
- samsung driver fixes (wasn't really being built)
- conmakeshash move to tty subdir out of scripts
- lots of small tty/serial driver updates
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXjFRBg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yn2VACgkge7vTeUNeZFc+6F4NWphAQ5tCQAoK/MMbU6
0O8ef7PjFwCU4s227UTv
=6m40
-----END PGP SIGNATURE-----
Merge tag 'tty-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here are the big set of tty and serial driver updates for 5.6-rc1
Included in here are:
- dummy_con cleanups (touches lots of arch code)
- sysrq logic cleanups (touches lots of serial drivers)
- samsung driver fixes (wasn't really being built)
- conmakeshash move to tty subdir out of scripts
- lots of small tty/serial driver updates
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (140 commits)
tty: n_hdlc: Use flexible-array member and struct_size() helper
tty: baudrate: SPARC supports few more baud rates
tty: baudrate: Synchronise baud_table[] and baud_bits[]
tty: serial: meson_uart: Add support for kernel debugger
serial: imx: fix a race condition in receive path
serial: 8250_bcm2835aux: Document struct bcm2835aux_data
serial: 8250_bcm2835aux: Use generic remapping code
serial: 8250_bcm2835aux: Allocate uart_8250_port on stack
serial: 8250_bcm2835aux: Suppress register_port error on -EPROBE_DEFER
serial: 8250_bcm2835aux: Suppress clk_get error on -EPROBE_DEFER
serial: 8250_bcm2835aux: Fix line mismatch on driver unbind
serial_core: Remove unused member in uart_port
vt: Correct comment documenting do_take_over_console()
vt: Delete comment referencing non-existent unbind_con_driver()
arch/xtensa/setup: Drop dummy_con initialization
arch/x86/setup: Drop dummy_con initialization
arch/unicore32/setup: Drop dummy_con initialization
arch/sparc/setup: Drop dummy_con initialization
arch/sh/setup: Drop dummy_con initialization
arch/s390/setup: Drop dummy_con initialization
...
Pull scheduler updates from Ingo Molnar:
"These were the main changes in this cycle:
- More -rt motivated separation of CONFIG_PREEMPT and
CONFIG_PREEMPTION.
- Add more low level scheduling topology sanity checks and warnings
to filter out nonsensical topologies that break scheduling.
- Extend uclamp constraints to influence wakeup CPU placement
- Make the RT scheduler more aware of asymmetric topologies and CPU
capacities, via uclamp metrics, if CONFIG_UCLAMP_TASK=y
- Make idle CPU selection more consistent
- Various fixes, smaller cleanups, updates and enhancements - please
see the git log for details"
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (58 commits)
sched/fair: Define sched_idle_cpu() only for SMP configurations
sched/topology: Assert non-NUMA topology masks don't (partially) overlap
idle: fix spelling mistake "iterrupts" -> "interrupts"
sched/fair: Remove redundant call to cpufreq_update_util()
sched/psi: create /proc/pressure and /proc/pressure/{io|memory|cpu} only when psi enabled
sched/fair: Fix sgc->{min,max}_capacity calculation for SD_OVERLAP
sched/fair: calculate delta runnable load only when it's needed
sched/cputime: move rq parameter in irqtime_account_process_tick
stop_machine: Make stop_cpus() static
sched/debug: Reset watchdog on all CPUs while processing sysrq-t
sched/core: Fix size of rq::uclamp initialization
sched/uclamp: Fix a bug in propagating uclamp value in new cgroups
sched/fair: Load balance aggressively for SCHED_IDLE CPUs
sched/fair : Improve update_sd_pick_busiest for spare capacity case
watchdog: Remove soft_lockup_hrtimer_cnt and related code
sched/rt: Make RT capacity-aware
sched/fair: Make EAS wakeup placement consider uclamp restrictions
sched/fair: Make task_fits_capacity() consider uclamp restrictions
sched/uclamp: Rename uclamp_util_with() into uclamp_rq_util_with()
sched/uclamp: Make uclamp util helpers use and return UL values
...
This patch ports the feature Kernel Address SANitizer (KASAN).
Note: The start address of shadow memory is at the beginning of kernel
space, which is 2^64 - (2^39 / 2) in SV39. The size of the kernel space is
2^38 bytes so the size of shadow memory should be 2^38 / 8. Thus, the
shadow memory would not overlap with the fixmap area.
There are currently two limitations in this port,
1. RV64 only: KASAN need large address space for extra shadow memory
region.
2. KASAN can't debug the modules since the modules are allocated in VMALLOC
area. We mapped the shadow memory, which corresponding to VMALLOC area, to
the kasan_early_shadow_page because we don't have enough physical space for
all the shadow memory corresponding to VMALLOC area.
Signed-off-by: Nick Hu <nickhu@andestech.com>
Reported-by: Greentime Hu <green.hu@gmail.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Temporary files used in the VDSO build process linger on even after make
mrproper: vdso-dummy.o.tmp, vdso.so.dbg.tmp.
Delete them once they're no longer needed.
Signed-off-by: Ilie Halip <ilie.halip@gmail.com>
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
The code in secondary_park is currently placed in the .init section. The
kernel reclaims and clears this code when it finishes booting. That
causes the cores parked in it to go to somewhere unpredictable, so we
move this function out of init to make sure the cores stay looping there.
The instruction bgeu a0, t0, .Lsecondary_park may have "a relocation
truncated to fit" issue during linking time. It is because that sections
are too far to jump. Let's use tail to jump to the .Lsecondary_park.
Signed-off-by: Greentime Hu <greentime.hu@sifive.com>
Reviewed-by: Anup Patel <anup.patel@sifive.com>
Cc: Andreas Schwab <schwab@suse.de>
Cc: stable@vger.kernel.org
Fixes: 76d2a0493a ("RISC-V: Init and Halt Code")
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
con_init in tty/vt.c will now set conswitchp to dummy_con if it's unset.
Drop it from arch setup code.
Signed-off-by: Arvind Sankar <nivedita@alum.mit.edu>
Link: https://lore.kernel.org/r/20191218214506.49252-19-nivedita@alum.mit.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Two fixes for RISC-V:
- Clear FP registers during boot when FP support is present, rather than
when they aren't present
- Move the header files associated with the SiFive L2 cache controller
to drivers/soc (where the code was recently moved)
-----BEGIN PGP SIGNATURE-----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=qvPe
-----END PGP SIGNATURE-----
Merge tag 'riscv/for-v5.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V fixes from Paul Walmsley:
"Two fixes for RISC-V:
- Clear FP registers during boot when FP support is present, rather
than when they aren't present
- Move the header files associated with the SiFive L2 cache
controller to drivers/soc (where the code was recently moved)"
* tag 'riscv/for-v5.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: Fixup obvious bug for fp-regs reset
riscv: move sifive_l2_cache.h to include/soc
CSR_MISA is defined in Privileged Architectures' spec: 3.1.1 Machine
ISA Register misa. Every bit:1 indicate a feature, so we should beqz
reset_done when there is no F/D bit in csr_misa register.
Signed-off-by: Guo Ren <ren_guo@c-sky.com>
[paul.walmsley@sifive.com: fix typo in commit message]
Fixes: 9e80635619 ("riscv: clear the instruction cache and all registers when booting")
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
"IRQ_TIMER", used in the arch/riscv CSR header file, is a sufficiently
generic macro name that it's used by several source files across the
Linux code base. Some of these other files ultimately include the
arch/riscv CSR include file, causing collisions. Fix by prefixing the
RISC-V csr.h IRQ_ macro names with an RV_ prefix.
Fixes: a4c3733d32 ("riscv: abstract out CSR names for supervisor vs machine mode")
Reported-by: Olof Johansson <olof@lixom.net>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
The condition should be logical NOT to assign the hook address to parent
address. Because the return value 0 of function_graph_enter upon
success.
Fixes: e949b6db51 (riscv/function_graph: Simplify with function_graph_enter())
Signed-off-by: Zong Li <zong.li@sifive.com>
Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Cc: stable@vger.kernel.org
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Running "stress-ng --enosys 4 -t 20 -v" showed a large number of kernel oops
with "Unable to handle kernel paging request at virtual address" message. This
happens when enosys stressor starts testing random non-valid syscalls.
I forgot to redirect any syscall below -1 to sys_ni_syscall.
With the patch kernel oops messages are gone while running stress-ng enosys
stressor.
Signed-off-by: David Abdurachmanov <david.abdurachmanov@sifive.com>
Fixes: 5340627e3f ("riscv: add support for SECCOMP and SECCOMP_FILTER")
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
When support for !MMU was added, the declaration of
__asm_copy_to_user() & __asm_copy_from_user() were #ifdefed
out hence their EXPORT_SYMBOL() give an error message like:
.../riscv_ksyms.c:13:15: error: '__asm_copy_to_user' undeclared here
.../riscv_ksyms.c:14:15: error: '__asm_copy_from_user' undeclared here
Since these symbols are not defined with !MMU it's wrong to export them.
Same for __clear_user() (even though this one is also declared in
include/asm-generic/uaccess.h and thus doesn't give an error message).
Fix this by doing the EXPORT_SYMBOL() directly where these symbols
are defined: inside lib/uaccess.S itself.
Fixes: 6bd33e1ece ("riscv: fix compile failure with EXPORT_SYMBOL() & !MMU")
Reported-by: kbuild test robot <lkp@intel.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
This patch fixes that the sscratch register clearing in M-mode. It cleared
sscratch register in M-mode, but it should clear mscratch register. That will
cause kernel trap if the CPU core doesn't support S-mode when trying to access
sscratch.
Fixes: 9e80635619 ("riscv: clear the instruction cache and all registers when booting")
Signed-off-by: Greentime Hu <greentime.hu@sifive.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
CONFIG_PREEMPTION is selected by CONFIG_PREEMPT and by CONFIG_PREEMPT_RT.
Both PREEMPT and PREEMPT_RT require the same functionality which today
depends on CONFIG_PREEMPT.
Switch the entry code over to use CONFIG_PREEMPTION.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Paul Walmsley <paul.walmsley@sifive.com> # for arch/riscv
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: linux-riscv@lists.infradead.org
Link: https://lore.kernel.org/r/20191015191821.11479-17-bigeasy@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
New features:
- SECCOMP support
- nommu support
- SBI-less system support
- M-Mode support
- TLB flush optimizations
Other improvements:
- Pass the complete RISC-V ISA string supported by the CPU cores to
userspace, rather than redacting parts of it in the kernel
- Add platform DMA IP block data to the HiFive Unleashed board DT file
- Add Makefile support for BZ2, LZ4, LZMA, LZO kernel image
compression formats, in line with other architectures
Cleanups:
- Remove unnecessary PTE_PARENT_SIZE macro
- Standardize include guard naming across arch/riscv
-----BEGIN PGP SIGNATURE-----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=nbwY
-----END PGP SIGNATURE-----
Merge tag 'riscv/for-v5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V updates from Paul Walmsley:
"New features:
- SECCOMP support
- nommu support
- SBI-less system support
- M-Mode support
- TLB flush optimizations
Other improvements:
- Pass the complete RISC-V ISA string supported by the CPU cores to
userspace, rather than redacting parts of it in the kernel
- Add platform DMA IP block data to the HiFive Unleashed board DT
file
- Add Makefile support for BZ2, LZ4, LZMA, LZO kernel image
compression formats, in line with other architectures
Cleanups:
- Remove unnecessary PTE_PARENT_SIZE macro
- Standardize include guard naming across arch/riscv"
* tag 'riscv/for-v5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux: (22 commits)
riscv: provide a flat image loader
riscv: add nommu support
riscv: clear the instruction cache and all registers when booting
riscv: read the hart ID from mhartid on boot
riscv: provide native clint access for M-mode
riscv: dts: add support for PDMA device of HiFive Unleashed Rev A00
riscv: add support for MMIO access to the timer registers
riscv: implement remote sfence.i using IPIs
riscv: cleanup the default power off implementation
riscv: poison SBI calls for M-mode
riscv: don't allow selecting SBI based drivers for M-mode
RISC-V: Add multiple compression image format.
riscv: clean up the macro format in each header file
riscv: Use PMD_SIZE to replace PTE_PARENT_SIZE
riscv: abstract out CSR names for supervisor vs machine mode
riscv: separate MMIO functions into their own header file
riscv: enter WFI in default_power_off() if SBI does not shutdown
RISC-V: Issue a tlb page flush if possible
RISC-V: Issue a local tlbflush if possible.
RISC-V: Do not invoke SBI call if cpumask is empty
...
Pull x86 asm updates from Ingo Molnar:
"The main changes in this cycle were:
- Cross-arch changes to move the linker sections for NOTES and
EXCEPTION_TABLE into the RO_DATA area, where they belong on most
architectures. (Kees Cook)
- Switch the x86 linker fill byte from x90 (NOP) to 0xcc (INT3), to
trap jumps into the middle of those padding areas instead of
sliding execution. (Kees Cook)
- A thorough cleanup of symbol definitions within x86 assembler code.
The rather randomly named macros got streamlined around a
(hopefully) straightforward naming scheme:
SYM_START(name, linkage, align...)
SYM_END(name, sym_type)
SYM_FUNC_START(name)
SYM_FUNC_END(name)
SYM_CODE_START(name)
SYM_CODE_END(name)
SYM_DATA_START(name)
SYM_DATA_END(name)
etc - with about three times of these basic primitives with some
label, local symbol or attribute variant, expressed via postfixes.
No change in functionality intended. (Jiri Slaby)
- Misc other changes, cleanups and smaller fixes"
* 'x86-asm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (67 commits)
x86/entry/64: Remove pointless jump in paranoid_exit
x86/entry/32: Remove unused resume_userspace label
x86/build/vdso: Remove meaningless CFLAGS_REMOVE_*.o
m68k: Convert missed RODATA to RO_DATA
x86/vmlinux: Use INT3 instead of NOP for linker fill bytes
x86/mm: Report actual image regions in /proc/iomem
x86/mm: Report which part of kernel image is freed
x86/mm: Remove redundant address-of operators on addresses
xtensa: Move EXCEPTION_TABLE to RO_DATA segment
powerpc: Move EXCEPTION_TABLE to RO_DATA segment
parisc: Move EXCEPTION_TABLE to RO_DATA segment
microblaze: Move EXCEPTION_TABLE to RO_DATA segment
ia64: Move EXCEPTION_TABLE to RO_DATA segment
h8300: Move EXCEPTION_TABLE to RO_DATA segment
c6x: Move EXCEPTION_TABLE to RO_DATA segment
arm64: Move EXCEPTION_TABLE to RO_DATA segment
alpha: Move EXCEPTION_TABLE to RO_DATA segment
x86/vmlinux: Move EXCEPTION_TABLE to RO_DATA segment
x86/vmlinux: Actually use _etext for the end of the text segment
vmlinux.lds.h: Allow EXCEPTION_TABLE to live in RO_DATA
...
-----BEGIN PGP SIGNATURE-----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=QCEy
-----END PGP SIGNATURE-----
Merge tag 'printk-for-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/pmladek/printk
Pull printk updates from Petr Mladek:
- Allow to print symbolic error names via new %pe modifier.
- Use pr_warn() instead of the remaining pr_warning() calls. Fix
formatting of the related lines.
- Add VSPRINTF entry to MAINTAINERS.
* tag 'printk-for-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/pmladek/printk: (32 commits)
checkpatch: don't warn about new vsprintf pointer extension '%pe'
MAINTAINERS: Add VSPRINTF
tools lib api: Renaming pr_warning to pr_warn
ASoC: samsung: Use pr_warn instead of pr_warning
lib: cpu_rmap: Use pr_warn instead of pr_warning
trace: Use pr_warn instead of pr_warning
dma-debug: Use pr_warn instead of pr_warning
vgacon: Use pr_warn instead of pr_warning
fs: afs: Use pr_warn instead of pr_warning
sh/intc: Use pr_warn instead of pr_warning
scsi: Use pr_warn instead of pr_warning
platform/x86: intel_oaktrail: Use pr_warn instead of pr_warning
platform/x86: asus-laptop: Use pr_warn instead of pr_warning
platform/x86: eeepc-laptop: Use pr_warn instead of pr_warning
oprofile: Use pr_warn instead of pr_warning
of: Use pr_warn instead of pr_warning
macintosh: Use pr_warn instead of pr_warning
idsn: Use pr_warn instead of pr_warning
ide: Use pr_warn instead of pr_warning
crypto: n2: Use pr_warn instead of pr_warning
...
The kernel runs in M-mode without using page tables, and thus can't run
bare metal without help from additional firmware.
Most of the patch is just stubbing out code not needed without page
tables, but there is an interesting detail in the signals implementation:
- The normal RISC-V syscall ABI only implements rt_sigreturn as VDSO
entry point, but the ELF VDSO is not supported for nommu Linux.
We instead copy the code to call the syscall onto the stack.
In addition to enabling the nommu code a new defconfig for a small
kernel image that can run in nommu mode on qemu is also provided, to run
a kernel in qemu you can use the following command line:
qemu-system-riscv64 -smp 2 -m 64 -machine virt -nographic \
-kernel arch/riscv/boot/loader \
-drive file=rootfs.ext2,format=raw,id=hd0 \
-device virtio-blk-device,drive=hd0
Contains contributions from Damien Le Moal <Damien.LeMoal@wdc.com>.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Anup Patel <anup@brainfault.org>
[paul.walmsley@sifive.com: updated to apply; add CONFIG_MMU guards
around PCI_IOBASE definition to fix build issues; fixed checkpatch
issues; move the PCI_IO_* and VMEMMAP address space macros along
with the others; resolve sparse warning]
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
When we get booted we want a clear slate without any leaks from previous
supervisors or the firmware. Flush the instruction cache and then clear
all registers to known good values. This is really important for the
upcoming nommu support that runs on M-mode, but can't really harm when
running in S-mode either. Vaguely based on the concepts from opensbi.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
When in M-Mode, we can use the mhartid CSR to get the ID of the running
HART. Doing so, direct M-Mode boot without firmware is possible.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
RISC-V has the concept of a cpu level interrupt controller. The
interface for it is split between a standardized part that is exposed
as bits in the mstatus/sstatus register and the mie/mip/sie/sip
CRS. But the bit to actually trigger IPIs is not standardized and
just mentioned as implementable using MMIO.
Add support for IPIs using MMIO using the SiFive clint layout (which
is also shared by Ariane, Kendryte and the Qemu virt platform).
Additionally the MMIO block also supports the time value and timer
compare registers, so they are also set up using the same OF node.
Support for other layouts should also be relatively easy to add in the
future.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Anup Patel <anup@brainfault.org>
[paul.walmsley@sifive.com: update include guard format; fix checkpatch
issues; minor commit message cleanup]
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Move the sbi poweroff to a separate function and file that is only
compiled if CONFIG_SBI is set.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
[paul.walmsley@sifive.com: split the WFI fix into a separate patch]
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Many of the privileged CSRs exist in a supervisor and machine version
that are used very similarly. Provide versions of the CSR names and
fields that map to either the S-mode or M-mode variant depending on
a new CONFIG_RISCV_M_MODE kconfig symbol.
Contains contributions from Damien Le Moal <Damien.LeMoal@wdc.com>
and Paul Walmsley <paul.walmsley@sifive.com>.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de> # for drivers/clocksource, drivers/irqchip
[paul.walmsley@sifive.com: updated to apply]
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Provide a new default fallback power off that just sits in a wfi loop
to save some power.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
[paul.walmsley@sifive.com: split the WFI fix apart from the
nommu-related default_power_off() changes]
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
This patch was extensively tested on Fedora/RISCV (applied by default on
top of 5.2-rc7 kernel for <2 months). The patch was also tested with 5.3-rc
on QEMU and SiFive Unleashed board.
libseccomp (userspace) was rebased:
https://github.com/seccomp/libseccomp/pull/134
Fully passes libseccomp regression testing (simulation and live).
There is one failing kernel selftest: global.user_notification_signal
v1 -> v2:
- return immediately if secure_computing(NULL) returns -1
- fixed whitespace issues
- add missing seccomp.h
- remove patch #2 (solved now)
- add riscv to seccomp kernel selftest
Signed-off-by: David Abdurachmanov <david.abdurachmanov@sifive.com>
Cc: keescook@chromium.org
Cc: me@carlosedp.com
Tested-by: Carlos de Paula <me@carlosedp.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/linux-riscv/CAEn-LTp=ss0Dfv6J00=rCAy+N78U2AmhqJNjfqjr2FDpPYjxEQ@mail.gmail.com/
Link: https://lore.kernel.org/linux-riscv/CAJr-aD=UnCN9E_mdVJ2H5nt=6juRSWikZnA5HxDLQxXLbsRz-w@mail.gmail.com/
[paul.walmsley@sifive.com: cleaned up Cc: lines; fixed spelling and
checkpatch issues; updated to apply]
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
/proc/cpuinfo should just print all the isa string as an information
instead of determining what is supported or not. ELF hwcap can be
used by the userspace to figure out that.
Simplify the isa string printing by removing the unsupported isa string
print and all related code.
The relevant discussion can be found at
http://lists.infradead.org/pipermail/linux-riscv/2019-September/006702.html
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: http://lists.infradead.org/pipermail/linux-riscv/2019-September/006702.html
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Rather than adding prototypes for C functions called only by assembly
code, mark them as __visible. This avoids adding prototypes that will
never be used by the callers. Resolves the following sparse warnings:
arch/riscv/kernel/irq.c:27:29: warning: symbol 'do_IRQ' was not declared. Should it be static?
arch/riscv/kernel/ptrace.c:151:6: warning: symbol 'do_syscall_trace_enter' was not declared. Should it be static?
arch/riscv/kernel/ptrace.c:165:6: warning: symbol 'do_syscall_trace_exit' was not declared. Should it be static?
arch/riscv/kernel/signal.c:295:17: warning: symbol 'do_notify_resume' was not declared. Should it be static?
arch/riscv/kernel/traps.c:92:1: warning: symbol 'do_trap_unknown' was not declared. Should it be static?
arch/riscv/kernel/traps.c:94:1: warning: symbol 'do_trap_insn_misaligned' was not declared. Should it be static?
arch/riscv/kernel/traps.c:96:1: warning: symbol 'do_trap_insn_fault' was not declared. Should it be static?
arch/riscv/kernel/traps.c:98:1: warning: symbol 'do_trap_insn_illegal' was not declared. Should it be static?
arch/riscv/kernel/traps.c💯1: warning: symbol 'do_trap_load_misaligned' was not declared. Should it be static?
arch/riscv/kernel/traps.c:102:1: warning: symbol 'do_trap_load_fault' was not declared. Should it be static?
arch/riscv/kernel/traps.c:104:1: warning: symbol 'do_trap_store_misaligned' was not declared. Should it be static?
arch/riscv/kernel/traps.c:106:1: warning: symbol 'do_trap_store_fault' was not declared. Should it be static?
arch/riscv/kernel/traps.c:108:1: warning: symbol 'do_trap_ecall_u' was not declared. Should it be static?
arch/riscv/kernel/traps.c:110:1: warning: symbol 'do_trap_ecall_s' was not declared. Should it be static?
arch/riscv/kernel/traps.c:112:1: warning: symbol 'do_trap_ecall_m' was not declared. Should it be static?
arch/riscv/kernel/traps.c:124:17: warning: symbol 'do_trap_break' was not declared. Should it be static?
arch/riscv/kernel/smpboot.c:136:24: warning: symbol 'smp_callin' was not declared. Should it be static?
Based on a suggestion from Luc Van Oostenryck.
This version includes changes based on feedback from Christoph Hellwig
<hch@lst.de>.
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de> # for do_syscall_trace_*
The __user annotations were removed from the {save,restore}_fp_state()
function signatures by commit 007f5c3589 ("Refactor FPU code in
signal setup/return procedures"), but should be present, and sparse
warns when they are not applied. Add them back in.
This change should have no functional impact.
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Fixes: 007f5c3589 ("Refactor FPU code in signal setup/return procedures")
Cc: Alan Kao <alankao@andestech.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
sparse identifies several missing prototypes caused by missing
preprocessor include directives:
arch/riscv/kernel/cpufeature.c:16:6: warning: symbol 'has_fpu' was not declared. Should it be static?
arch/riscv/kernel/process.c:26:6: warning: symbol 'arch_cpu_idle' was not declared. Should it be static?
arch/riscv/kernel/reset.c:15:6: warning: symbol 'pm_power_off' was not declared. Should it be static?
arch/riscv/kernel/syscall_table.c:15:6: warning: symbol 'sys_call_table' was not declared. Should it be static?
arch/riscv/kernel/traps.c:149:13: warning: symbol 'trap_init' was not declared. Should it be static?
arch/riscv/kernel/vdso.c:54:5: warning: symbol 'arch_setup_additional_pages' was not declared. Should it be static?
arch/riscv/kernel/smp.c:64:6: warning: symbol 'arch_match_cpu_phys_id' was not declared. Should it be static?
arch/riscv/kernel/module-sections.c:89:5: warning: symbol 'module_frob_arch_sections' was not declared. Should it be static?
arch/riscv/mm/context.c:42:6: warning: symbol 'switch_mm' was not declared. Should it be static?
Fix by including the appropriate header files in the appropriate
source files.
This patch should have no functional impact.
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Several functions and arrays which are only used in the files in which
they are declared are missing "static" qualifiers. Warnings for these
symbols are reported by sparse:
arch/riscv/kernel/vdso.c:28:18: warning: symbol 'vdso_data' was not declared. Should it be static?
arch/riscv/mm/sifive_l2_cache.c:145:12: warning: symbol 'sifive_l2_init' was not declared. Should it be static?
Resolve these warnings by marking them as static.
This version incorporates feedback from Greentime Hu
<greentime.hu@sifive.com>.
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Greentime Hu <greentime.hu@sifive.com>
Add prototypes for assembly language functions defined in head.S,
and include these prototypes into C source files that call those
functions.
This patch resolves the following warnings from sparse:
arch/riscv/kernel/setup.c:39:10: warning: symbol 'hart_lottery' was not declared. Should it be static?
arch/riscv/kernel/setup.c:42:13: warning: symbol 'parse_dtb' was not declared. Should it be static?
arch/riscv/kernel/smpboot.c:33:6: warning: symbol '__cpu_up_stack_pointer' was not declared. Should it be static?
arch/riscv/kernel/smpboot.c:34:6: warning: symbol '__cpu_up_task_pointer' was not declared. Should it be static?
arch/riscv/mm/fault.c:25:17: warning: symbol 'do_page_fault' was not declared. Should it be static?
This change should have no functional impact.
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
If we always compile the get_break_insn_length inline function we can
remove the ifdefs and let dead code elimination take care of the warn
branch that is now unreadable because the report_bug stub always
returns BUG_TRAP_TYPE_BUG.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
As said in commit f2c2cbcc35 ("powerpc: Use pr_warn instead of
pr_warning"), removing pr_warning so all logging messages use a
consistent <prefix>_warn style. Let's do it.
Link: http://lkml.kernel.org/r/20191018031850.48498-4-wangkefeng.wang@huawei.com
To: linux-kernel@vger.kernel.org
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Acked-by: Palmer Dabbelt <palmer@sifive.com>
Reviewed-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Since the enabling and disabling of IRQs within preempt_schedule_irq()
is contained in a need_resched() loop, we don't need the outer arch
code loop.
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Valentin Schneider <valentin.schneider@arm.com>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: linux-riscv@lists.infradead.org
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
For the kernel space, all ebreak instructions are determined at compile
time because the kernel space debugging module is currently unsupported.
Hence, it should be treated as a bug if an ebreak instruction which does
not belong to BUG_TRAP_TYPE_WARN or BUG_TRAP_TYPE_BUG is executed in
kernel space. For the userspace, debugging module or user problem may
intentionally insert an ebreak instruction to trigger a SIGTRAP signal.
To approach the above two situations, the do_trap_break() will direct
the BUG_TRAP_TYPE_NONE ebreak exception issued in kernel space to die()
and will send a SIGTRAP to the trapped process only when the ebreak is
in userspace.
Signed-off-by: Vincent Chen <vincent.chen@sifive.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
[paul.walmsley@sifive.com: fixed checkpatch issue]
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
On RISC-V, when the kernel runs code on behalf of a user thread, and the
kernel executes a WARN() or WARN_ON(), the user thread will be sent
a bogus SIGTRAP. Fix the RISC-V kernel code to not send a SIGTRAP when
a WARN()/WARN_ON() is executed.
Signed-off-by: Vincent Chen <vincent.chen@sifive.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
[paul.walmsley@sifive.com: fixed subject]
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
When the CONFIG_GENERIC_BUG is disabled by disabling CONFIG_BUG, if a
kernel thread is trapped by BUG(), the whole system will be in the
loop that infinitely handles the ebreak exception instead of entering the
die function. To fix this problem, the do_trap_break() will always call
the die() to deal with the break exception as the type of break is
BUG_TRAP_TYPE_BUG.
Signed-off-by: Vincent Chen <vincent.chen@sifive.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
This is almost entirely a comment. The bug is unlikely to manifest on
existing hardware because there is a timeout on load reservations, but
manifests on QEMU because there is no timeout.
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
When the handle_exception function addresses an exception, the interrupts
will be unconditionally enabled after finishing the context save. However,
It may erroneously enable the interrupts if the interrupts are disabled
before entering the handle_exception.
For example, one of the WARN_ON() condition is satisfied in the scheduling
where the interrupt is disabled and rq.lock is locked. The WARN_ON will
trigger a break exception and the handle_exception function will enable the
interrupts before entering do_trap_break function. During the procedure, if
a timer interrupt is pending, it will be taken when interrupts are enabled.
In this case, it may cause a deadlock problem if the rq.lock is locked
again in the timer ISR.
Hence, the handle_exception() can only enable interrupts when the state of
sstatus.SPIE is 1.
This patch is tested on HiFive Unleashed board.
Signed-off-by: Vincent Chen <vincent.chen@sifive.com>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
[paul.walmsley@sifive.com: updated to apply]
Fixes: bcae803a21 ("RISC-V: Enable IRQ during exception handling")
Cc: David Abdurachmanov <david.abdurachmanov@sifive.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Export a few symbols used by kvm module. Without this, kvm cannot
be compiled as a module.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Alexander Graf <graf@amazon.com>
[paul.walmsley@sifive.com: updated to apply; clarified short patch
description]
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Harts with id greater than or equal to CONFIG_NR_CPUS need to be
disabled. But the kernel can pick any hart as the main hart. So,
before picking the main hart, the kernel must disable harts with ids
greater than or equal to CONFIG_NR_CPUS.
Signed-off-by: Xiang Wang <merle@hardenedlinux.org>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
[paul.walmsley@sifive.com: updated to apply; cleaned up patch
description]
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Add the following new features:
- Generic CPU topology description support for DT-based platforms,
including ARM64, ARM and RISC-V.
- Sparsemem support
- Perf callchain support
- SiFive PLIC irqchip modifications, in preparation for M-mode Linux
and clean up the code base:
- Clean up chip-specific register (CSR) manipulation code, IPIs, TLB
flushing, and the RISC-V CPU-local timer code
- Kbuild cleanup from one of the Kbuild maintainers
-----BEGIN PGP SIGNATURE-----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=N9WW
-----END PGP SIGNATURE-----
Merge tag 'riscv/for-v5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V updates from Paul Walmsley:
"Add the following new features:
- Generic CPU topology description support for DT-based platforms,
including ARM64, ARM and RISC-V.
- Sparsemem support
- Perf callchain support
- SiFive PLIC irqchip modifications, in preparation for M-mode Linux
and clean up the code base:
- Clean up chip-specific register (CSR) manipulation code, IPIs, TLB
flushing, and the RISC-V CPU-local timer code
- Kbuild cleanup from one of the Kbuild maintainers"
[ The CPU topology parts came in through the arm64 tree with a shared
branch - Linus ]
* tag 'riscv/for-v5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
irqchip/sifive-plic: set max threshold for ignored handlers
riscv: move the TLB flush logic out of line
riscv: don't use the rdtime(h) pseudo-instructions
riscv: cleanup riscv_cpuid_to_hartid_mask
riscv: optimize send_ipi_single
riscv: cleanup send_ipi_mask
riscv: refactor the IPI code
riscv: Add support for libdw
riscv: Add support for perf registers sampling
riscv: Add perf callchain support
riscv: add arch/riscv/Kbuild
RISC-V: Implement sparsemem
riscv: Using CSR numbers to access CSRs
- 52-bit virtual addressing in the kernel
- New ABI to allow tagged user pointers to be dereferenced by syscalls
- Early RNG seeding by the bootloader
- Improve robustness of SMP boot
- Fix TLB invalidation in light of recent architectural clarifications
- Support for i.MX8 DDR PMU
- Remove direct LSE instruction patching in favour of static keys
- Function error injection using kprobes
- Support for the PPTT "thread" flag introduced by ACPI 6.3
- Move PSCI idle code into proper cpuidle driver
- Relaxation of implicit I/O memory barriers
- Build with RELR relocations when toolchain supports them
- Numerous cleanups and non-critical fixes
-----BEGIN PGP SIGNATURE-----
iQFEBAABCgAuFiEEPxTL6PPUbjXGY88ct6xw3ITBYzQFAl1yYREQHHdpbGxAa2Vy
bmVsLm9yZwAKCRC3rHDchMFjNAM3CAChqDFQkryXoHwdeEcaukMRVNxtxOi4pM4g
5xqkb7PoqRJssIblsuhaXjrSD97yWCgaqCmFe6rKoes++lP4bFcTe22KXPPyPBED
A+tK4nTuKKcZfVbEanUjI+ihXaHJmKZ/kwAxWsEBYZ4WCOe3voCiJVNO2fHxqg1M
8TskZ2BoayTbWMXih0eJg2MCy/xApBq4b3nZG4bKI7Z9UpXiKN1NYtDh98ZEBK4V
d/oNoHsJ2ZvIQsztoBJMsvr09DTCazCijWZiECadm6l41WEPFizngrACiSJLLtYo
0qu4qxgg9zgFlvBCRQmIYSggTuv35RgXSfcOwChmW5DUjHG+f9GK
=Ru4B
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Will Deacon:
"Although there isn't tonnes of code in terms of line count, there are
a fair few headline features which I've noted both in the tag and also
in the merge commits when I pulled everything together.
The part I'm most pleased with is that we had 35 contributors this
time around, which feels like a big jump from the usual small group of
core arm64 arch developers. Hopefully they all enjoyed it so much that
they'll continue to contribute, but we'll see.
It's probably worth highlighting that we've pulled in a branch from
the risc-v folks which moves our CPU topology code out to where it can
be shared with others.
Summary:
- 52-bit virtual addressing in the kernel
- New ABI to allow tagged user pointers to be dereferenced by
syscalls
- Early RNG seeding by the bootloader
- Improve robustness of SMP boot
- Fix TLB invalidation in light of recent architectural
clarifications
- Support for i.MX8 DDR PMU
- Remove direct LSE instruction patching in favour of static keys
- Function error injection using kprobes
- Support for the PPTT "thread" flag introduced by ACPI 6.3
- Move PSCI idle code into proper cpuidle driver
- Relaxation of implicit I/O memory barriers
- Build with RELR relocations when toolchain supports them
- Numerous cleanups and non-critical fixes"
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (114 commits)
arm64: remove __iounmap
arm64: atomics: Use K constraint when toolchain appears to support it
arm64: atomics: Undefine internal macros after use
arm64: lse: Make ARM64_LSE_ATOMICS depend on JUMP_LABEL
arm64: asm: Kill 'asm/atomic_arch.h'
arm64: lse: Remove unused 'alt_lse' assembly macro
arm64: atomics: Remove atomic_ll_sc compilation unit
arm64: avoid using hard-coded registers for LSE atomics
arm64: atomics: avoid out-of-line ll/sc atomics
arm64: Use correct ll/sc atomic constraints
jump_label: Don't warn on __exit jump entries
docs/perf: Add documentation for the i.MX8 DDR PMU
perf/imx_ddr: Add support for AXI ID filtering
arm64: kpti: ensure patched kernel text is fetched from PoU
arm64: fix fixmap copy for 16K pages and 48-bit VA
perf/smmuv3: Validate groups for global filtering
perf/smmuv3: Validate group size
arm64: Relax Documentation/arm64/tagged-pointers.rst
arm64: kvm: Replace hardcoded '1' with SYS_PAR_EL1_F
arm64: mm: Ignore spurious translation faults taken from the kernel
...
Part of the intention during the definition of the RISC-V kernel image
header was to lay the groundwork for a future merge with the ARM64
image header. One error during my original review was not noticing
that the RISC-V header's "magic" field was at a different size and
position than the ARM64's "magic" field. If the existing ARM64 Image
header parsing code were to attempt to parse an existing RISC-V kernel
image header format, it would see a magic number 0. This is
undesirable, since it's our intention to align as closely as possible
with the ARM64 header format. Another problem was that the original
"res3" field was not being initialized correctly to zero.
Address these issues by creating a 32-bit "magic2" field in the RISC-V
header which matches the ARM64 "magic" field. RISC-V binaries will
store "RSC\x05" in this field. The intention is that the use of the
existing 64-bit "magic" field in the RISC-V header will be deprecated
over time. Increment the minor version number of the file format to
indicate this change, and update the documentation accordingly. Fix
the assembler directives in head.S to ensure that reserved fields are
properly zero-initialized.
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Reported-by: Palmer Dabbelt <palmer@sifive.com>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
Cc: Atish Patra <atish.patra@wdc.com>
Cc: Karsten Merker <merker@debian.org>
Link: https://lore.kernel.org/linux-riscv/194c2f10c9806720623430dbf0cc59a965e50448.camel@wdc.com/T/#u
Link: https://lore.kernel.org/linux-riscv/mhng-755b14c4-8f35-4079-a7ff-e421fd1b02bc@palmer-si-x1e/T/#t
Move the initial clearing of the mask from the callers to
riscv_cpuid_to_hartid_mask, and remove the unused !CONFIG_SMP stub.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Don't go through send_ipi_mask, but just set the op bit and then pass
a simple generated hartid mask directly to sbi_send_ipi.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
[paul.walmsley@sifive.com: minor patch description fixes]
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Use the special barriers for atomic bitops to make the intention
a little more clear, and use riscv_cpuid_to_hartid_mask instead of
open coding it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
This prepares for adding native non-SBI IPI code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
This patch implements the perf registers sampling and validation API
for the riscv arch. The valid registers and their register ID are
defined in perf_regs.h. Perf tool can backtrace in userspace with
unwind library and the registers/user stack dump support.
Signed-off-by: Mao Han <han_mao@c-sky.com>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: linux-riscv <linux-riscv@lists.infradead.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Guo Ren <guoren@kernel.org>
Tested-by: Greentime Hu <greentime.hu@sifive.com>
[paul.walmsley@sifive.com: minor patch description fix]
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
This patch add support for perf callchain sampling on riscv platforms.
The return address of leaf function is retrieved from pt_regs as
it is not saved in the outmost frame.
Signed-off-by: Mao Han <han_mao@c-sky.com>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: linux-riscv <linux-riscv@lists.infradead.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Guo Ren <guoren@kernel.org>
Tested-by: Greentime Hu <greentime.hu@sifive.com>
[paul.walmsley@sifive.com: fixed some 'checkpatch.pl --strict' issues;
fixed patch description spelling]
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Since commit a3182c91ef ("RISC-V: Access CSRs using CSR numbers"),
we should prefer accessing CSRs using their CSR numbers, but there
are several leftovers like sstatus / sptbr we missed.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
The following two reasons cause FP registers are sometimes not
initialized before starting the user program.
1. Currently, the FP context is initialized in flush_thread() function
and we expect these initial values to be restored to FP register when
doing FP context switch. However, the FP context switch only occurs in
switch_to function. Hence, if this process does not be scheduled out
and scheduled in before entering the user space, the FP registers
have no chance to initialize.
2. In flush_thread(), the state of reg->sstatus.FS inherits from the
parent. Hence, the state of reg->sstatus.FS may be dirty. If this
process is scheduled out during flush_thread() and initializing the
FP register, the fstate_save() in switch_to will corrupt the FP context
which has been initialized until flush_thread().
To solve the 1st case, the initialization of the FP register will be
completed in start_thread(). It makes sure all FP registers are initialized
before starting the user program. For the 2nd case, the state of
reg->sstatus.FS in start_thread will be set to SR_FS_OFF to prevent this
process from corrupting FP context in doing context save. The FP state is
set to SR_FS_INITIAL in start_trhead().
Signed-off-by: Vincent Chen <vincent.chen@sifive.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Fixes: 7db91e57a0 ("RISC-V: Task implementation")
Cc: stable@vger.kernel.org
[paul.walmsley@sifive.com: fixed brace alignment issue reported by
checkpatch]
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Pull in generic CPU topology changes from Paul Walmsley (RISC-V).
* tag 'common/for-v5.4-rc1/cpu-topology' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
MAINTAINERS: Add an entry for generic architecture topology
base: arch_topology: update Kconfig help description
RISC-V: Parse cpu topology during boot.
arm: Use common cpu_topology structure and functions.
cpu-topology: Move cpu topology code to common code.
dt-binding: cpu-topology: Move cpu-map to a common binding.
Documentation: DT: arm: add support for sockets defining package boundaries
This patch fix following perf record error by linking vdso.so with
build id.
perf.data perf.data.old
[ perf record: Woken up 1 times to write data ]
free(): double free detected in tcache 2
Aborted
perf record use filename__read_build_id(util/symbol-minimal.c) to get
build id when libelf is not supported. When vdso.so is linked without
build id, the section size of PT_NOTE will be zero, buf size will
realloc to zero and cause memory corruption.
Signed-off-by: Mao Han <han_mao@c-sky.com>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Currently, there are no topology defined for RISC-V.
Parse the cpu-map node from device tree and setup the
cpu topology.
CPU topology after applying the patch.
$cat /sys/devices/system/cpu/cpu2/topology/core_siblings_list
0-3
$cat /sys/devices/system/cpu/cpu3/topology/core_siblings_list
0-3
$cat /sys/devices/system/cpu/cpu3/topology/physical_package_id
0
$cat /sys/devices/system/cpu/cpu3/topology/core_id
3
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
- Hugepage support
- "Image" header support for RISC-V kernel binaries, compatible with
the current ARM64 "Image" header
- Initial page table setup now split into two stages
- CONFIG_SOC support (starting with SiFive SoCs)
- Avoid reserving memory between RAM start and the kernel in setup_bootmem()
- Enable high-res timers and dynamic tick in the RV64 defconfig
- Remove long-deprecated gate area stubs
- MAINTAINERS updates to switch to the newly-created shared RISC-V git
tree, and to fix a get_maintainers.pl issue for patches involving
SiFive E-mail addresses
Also, one integration fix to resolve a build problem introduced during
in the v5.3-rc1 merge window:
- Fix build break after macro-to-function conversion in
asm-generic/cacheflush.h
-----BEGIN PGP SIGNATURE-----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=SVSp
-----END PGP SIGNATURE-----
Merge tag 'riscv/for-v5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V updates from Paul Walmsley:
- Hugepage support
- "Image" header support for RISC-V kernel binaries, compatible with
the current ARM64 "Image" header
- Initial page table setup now split into two stages
- CONFIG_SOC support (starting with SiFive SoCs)
- Avoid reserving memory between RAM start and the kernel in
setup_bootmem()
- Enable high-res timers and dynamic tick in the RV64 defconfig
- Remove long-deprecated gate area stubs
- MAINTAINERS updates to switch to the newly-created shared RISC-V git
tree, and to fix a get_maintainers.pl issue for patches involving
SiFive E-mail addresses
Also, one integration fix to resolve a build problem introduced during
in the v5.3-rc1 merge window:
- Fix build break after macro-to-function conversion in
asm-generic/cacheflush.h
* tag 'riscv/for-v5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: fix build break after macro-to-function conversion in generic cacheflush.h
RISC-V: Add an Image header that boot loader can parse.
RISC-V: Setup initial page tables in two stages
riscv: remove free_initrd_mem
riscv: ccache: Remove unused variable
riscv: Introduce huge page support for 32/64bit kernel
x86, arm64: Move ARCH_WANT_HUGE_PMD_SHARE config in arch/Kconfig
RISC-V: Fix memory reservation in setup_bootmem()
riscv: defconfig: enable SOC_SIFIVE
riscv: select SiFive platform drivers with SOC_SIFIVE
arch: riscv: add config option for building SiFive's SoC resource
riscv: Remove gate area stubs
MAINTAINERS: change the arch/riscv git tree to the new shared tree
MAINTAINERS: don't automatically patches involving SiFive to the linux-riscv list
RISC-V: defconfig: Enable NO_HZ_IDLE and HIGH_RES_TIMERS
Currently, the last stage boot loaders such as U-Boot can accept only
uImage which is an unnecessary additional step in automating boot
process.
Add an image header that boot loader understands and boot Linux from
flat Image directly.
This header is based on ARM64 boot image header and provides an
opportunity to combine both ARM64 & RISC-V image headers in future.
Also make sure that PE/COFF header can co-exist in the same image so
that EFI stub can be supported for RISC-V in future. EFI specification
needs PE/COFF image header in the beginning of the kernel image in order
to load it as an EFI application. In order to support EFI stub, code0
should be replaced with "MZ" magic string and res4(at offset 0x3c)
should point to the rest of the PE/COFF header (which will be added
during EFI support).
Tested on both QEMU and HiFive Unleashed using OpenSBI + U-Boot + Linux.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Karsten Merker <merker@debian.org>
Tested-by: Karsten Merker <merker@debian.org> (QEMU+OpenSBI+U-Boot)
Tested-by: Kevin Hilman <khilman@baylibre.com> (OpenSBI + U-Boot + Linux)
[paul.walmsley@sifive.com: fixed whitespace in boot-image-header.txt;
converted structure comment to kernel-doc format and added some detail]
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Currently, the setup_vm() does initial page table setup in one-shot
very early before enabling MMU. Due to this, the setup_vm() has to map
all possible kernel virtual addresses since it does not know size and
location of RAM. This means we have kernel mappings for non-existent
RAM and any buggy driver (or kernel) code doing out-of-bound access
to RAM will not fault and cause underterministic behaviour.
Further, the setup_vm() creates PMD mappings (i.e. 2M mappings) for
RV64 systems. This means for PAGE_OFFSET=0xffffffe000000000 (i.e.
MAXPHYSMEM_128GB=y), the setup_vm() will require 129 pages (i.e.
516 KB) of memory for initial page tables which is never freed. The
memory required for initial page tables will further increase if
we chose a lower value of PAGE_OFFSET (e.g. 0xffffff0000000000)
This patch implements two-staged initial page table setup, as follows:
1. Early (i.e. setup_vm()): This stage maps kernel image and DTB in
a early page table (i.e. early_pg_dir). The early_pg_dir will be used
only by boot HART so it can be freed as-part of init memory free-up.
2. Final (i.e. setup_vm_final()): This stage maps all possible RAM
banks in the final page table (i.e. swapper_pg_dir). The boot HART
will start using swapper_pg_dir at the end of setup_vm_final(). All
non-boot HARTs directly use the swapper_pg_dir created by boot HART.
We have following advantages with this new approach:
1. Kernel mappings for non-existent RAM don't exists anymore.
2. Memory consumed by initial page tables is now indpendent of the
chosen PAGE_OFFSET.
3. Memory consumed by initial page tables on RV64 system is 2 pages
(i.e. 8 KB) which has significantly reduced and these pages will be
freed as-part of the init memory free-up.
The patch also provides a foundation for implementing strict kernel
mappings where we protect kernel text and rodata using PTE permissions.
Suggested-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Anup Patel <anup.patel@wdc.com>
[paul.walmsley@sifive.com: updated to apply; fixed a checkpatch warning]
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Pull force_sig() argument change from Eric Biederman:
"A source of error over the years has been that force_sig has taken a
task parameter when it is only safe to use force_sig with the current
task.
The force_sig function is built for delivering synchronous signals
such as SIGSEGV where the userspace application caused a synchronous
fault (such as a page fault) and the kernel responded with a signal.
Because the name force_sig does not make this clear, and because the
force_sig takes a task parameter the function force_sig has been
abused for sending other kinds of signals over the years. Slowly those
have been fixed when the oopses have been tracked down.
This set of changes fixes the remaining abusers of force_sig and
carefully rips out the task parameter from force_sig and friends
making this kind of error almost impossible in the future"
* 'siginfo-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace: (27 commits)
signal/x86: Move tsk inside of CONFIG_MEMORY_FAILURE in do_sigbus
signal: Remove the signal number and task parameters from force_sig_info
signal: Factor force_sig_info_to_task out of force_sig_info
signal: Generate the siginfo in force_sig
signal: Move the computation of force into send_signal and correct it.
signal: Properly set TRACE_SIGNAL_LOSE_INFO in __send_signal
signal: Remove the task parameter from force_sig_fault
signal: Use force_sig_fault_to_task for the two calls that don't deliver to current
signal: Explicitly call force_sig_fault on current
signal/unicore32: Remove tsk parameter from __do_user_fault
signal/arm: Remove tsk parameter from __do_user_fault
signal/arm: Remove tsk parameter from ptrace_break
signal/nds32: Remove tsk parameter from send_sigtrap
signal/riscv: Remove tsk parameter from do_trap
signal/sh: Remove tsk parameter from force_sig_info_fault
signal/um: Remove task parameter from send_sigtrap
signal/x86: Remove task parameter from send_sigtrap
signal: Remove task parameter from force_sig_mceerr
signal: Remove task parameter from force_sig
signal: Remove task parameter from force_sigsegv
...
Since commit a6c19dfe39 ("arm64,ia64,ppc,s390,sh,tile,um,x86,mm:
remove default gate area"), which predates riscv's inclusion in
Linux by almost three years, the default behavior wrt the gate area
is sane. Remove riscv's gate area stubs.
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: linux-riscv@lists.infradead.org
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Another round of SPDX updates for 5.2-rc6
Here is what I am guessing is going to be the last "big" SPDX update for
5.2. It contains all of the remaining GPLv2 and GPLv2+ updates that
were "easy" to determine by pattern matching. The ones after this are
going to be a bit more difficult and the people on the spdx list will be
discussing them on a case-by-case basis now.
Another 5000+ files are fixed up, so our overall totals are:
Files checked: 64545
Files with SPDX: 45529
Compared to the 5.1 kernel which was:
Files checked: 63848
Files with SPDX: 22576
This is a huge improvement.
Also, we deleted another 20000 lines of boilerplate license crud, always
nice to see in a diffstat.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXQyQYA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymnGQCghETUBotn1p3hTjY56VEs6dGzpHMAnRT0m+lv
kbsjBGEJpLbMRB2krnaU
=RMcT
-----END PGP SIGNATURE-----
Merge tag 'spdx-5.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx
Pull still more SPDX updates from Greg KH:
"Another round of SPDX updates for 5.2-rc6
Here is what I am guessing is going to be the last "big" SPDX update
for 5.2. It contains all of the remaining GPLv2 and GPLv2+ updates
that were "easy" to determine by pattern matching. The ones after this
are going to be a bit more difficult and the people on the spdx list
will be discussing them on a case-by-case basis now.
Another 5000+ files are fixed up, so our overall totals are:
Files checked: 64545
Files with SPDX: 45529
Compared to the 5.1 kernel which was:
Files checked: 63848
Files with SPDX: 22576
This is a huge improvement.
Also, we deleted another 20000 lines of boilerplate license crud,
always nice to see in a diffstat"
* tag 'spdx-5.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx: (65 commits)
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 507
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 506
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 505
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 504
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 503
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 502
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 501
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 500
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 499
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 498
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 497
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 496
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 495
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 491
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 490
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 489
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 488
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 487
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 486
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 485
...
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not see http www gnu org
licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 503 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Enrico Weigelt <info@metux.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190602204653.811534538@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This tag contains fixes, defconfig, and DT data changes for the v5.2-rc
series. The fixes are relatively straightforward:
- Addition of a TLB fence in the vmalloc_fault path, so the CPU doesn't
enter an infinite page fault loop;
- Readdition of the pm_power_off export, so device drivers that
reassign it can now be built as modules;
- A udelay() fix for RV32, fixing a miscomputation of the delay time;
- Removal of deprecated smp_mb__*() barriers.
The tag also adds initial DT data infrastructure for arch/riscv, along
with initial data for the SiFive FU540-C000 SoC and the corresponding
HiFive Unleashed board.
We also update the RV64 defconfig to include some core drivers for the
FU540 in the build.
-----BEGIN PGP SIGNATURE-----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=aotJ
-----END PGP SIGNATURE-----
Merge tag 'riscv-for-v5.2/fixes-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V fixes from Paul Walmsley:
"This contains fixes, defconfig, and DT data changes for the v5.2-rc
series.
The fixes are relatively straightforward:
- Addition of a TLB fence in the vmalloc_fault path, so the CPU
doesn't enter an infinite page fault loop
- Readdition of the pm_power_off export, so device drivers that
reassign it can now be built as modules
- A udelay() fix for RV32, fixing a miscomputation of the delay time
- Removal of deprecated smp_mb__*() barriers
This also adds initial DT data infrastructure for arch/riscv, along
with initial data for the SiFive FU540-C000 SoC and the corresponding
HiFive Unleashed board.
We also update the RV64 defconfig to include some core drivers for the
FU540 in the build"
* tag 'riscv-for-v5.2/fixes-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: remove unused barrier defines
riscv: mm: synchronize MMU after pte change
riscv: dts: add initial board data for the SiFive HiFive Unleashed
riscv: dts: add initial support for the SiFive FU540-C000 SoC
dt-bindings: riscv: convert cpu binding to json-schema
dt-bindings: riscv: sifive: add YAML documentation for the SiFive FU540
arch: riscv: add support for building DTB files from DT source data
riscv: Fix udelay in RV32.
riscv: export pm_power_off again
RISC-V: defconfig: enable clocks, serial console
Commit bf0102a0fd ("riscv: call pm_power_off from machine_halt /
machine_power_off") removed the export of pm_power_off, but it is used by
several modules:
ERROR: "pm_power_off" [drivers/mfd/rk808.ko] undefined!
ERROR: "pm_power_off" [drivers/mfd/max8907.ko] undefined!
ERROR: "pm_power_off" [drivers/mfd/axp20x.ko] undefined!
ERROR: "pm_power_off" [drivers/char/ipmi/ipmi_poweroff.ko] undefined!
Signed-off-by: Andreas Schwab <schwab@suse.de>
Fixes: bf0102a0fd ("riscv: call pm_power_off from machine_halt / machine_power_off")
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation version 2 this program is distributed
in the hope that it will be useful but without any warranty without
even the implied warranty of merchantability or fitness for a
particular purpose see the gnu general public license for more
details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 97 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141901.025053186@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 655 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070034.575739538@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 3 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version [author] [kishon] [vijay] [abraham]
[i] [kishon]@[ti] [com] this program is distributed in the hope that
it will be useful but without any warranty without even the implied
warranty of merchantability or fitness for a particular purpose see
the gnu general public license for more details
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version [author] [graeme] [gregory]
[gg]@[slimlogic] [co] [uk] [author] [kishon] [vijay] [abraham] [i]
[kishon]@[ti] [com] [based] [on] [twl6030]_[usb] [c] [author] [hema]
[hk] [hemahk]@[ti] [com] this program is distributed in the hope
that it will be useful but without any warranty without even the
implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1105 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.202006027@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As synchronous exceptions really only make sense against the current
task (otherwise how are you synchronous) remove the task parameter
from from force_sig_fault to make it explicit that is what is going
on.
The two known exceptions that deliver a synchronous exception to a
stopped ptraced task have already been changed to
force_sig_fault_to_task.
The callers have been changed with the following emacs regular expression
(with obvious variations on the architectures that take more arguments)
to avoid typos:
force_sig_fault[(]\([^,]+\)[,]\([^,]+\)[,]\([^,]+\)[,]\W+current[)]
->
force_sig_fault(\1,\2,\3)
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Update the calls of force_sig_fault that pass in a variable that is
set to current earlier to explicitly use current.
This is to make the next change that removes the task parameter
from force_sig_fault easier to verify.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
The do_trap function is always called with tsk == current.
Make that obvious by removing the tsk parameter.
This also makes it clear that do_trap calls force_sig_fault
on the current task.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
All of the remaining callers pass current into force_sig so
remove the task parameter to make this obvious and to make
misuse more difficult in the future.
This also makes it clear force_sig passes current into force_sig_info.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not see the file copying or write to the free
software foundation inc
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 12 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190523091651.231300438@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch set contains an assortment of RISC-V related patches that I'd
like to target for the 5.2 merge window. Most of the patches are
cleanups, but there are a handful of user-visible changes:
* The nosmp and nr_cpus command-line arguments are now supported, which
work like normal.
* The SBI console no longer installs itself as a preferred console, we
rely on standard mechanisms (/chosen, command-line, hueristics)
instead.
* sfence_remove_sfence_vma{,_asid} now pass their arguments along to the
SBI call.
* Modules now support BUG().
* A missing sfence.vma during boot has been added. This bug only
manifests during boot.
* The arch/riscv support for SiFive's L2 cache controller has been
merged, which should un-block the EDAC framework work.
I've only tested this on QEMU again, as I didn't have time to get things
running on the Unleashed. The latest master from this morning merges in
cleanly and passes the tests as well.
This patch set rebased my "5.2 MW, Part 1" patch set which includes an
erronous empty file. It's also a rebase of my "5.2 MW, Part 2" patch
set, in which I managed to create another file while attempting to
remove the empty file.
Sorry for all the noise!
-----BEGIN PGP SIGNATURE-----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=mZwx
-----END PGP SIGNATURE-----
Merge tag 'riscv-for-linus-5.2-mw2' of git://git.kernel.org/pub/scm/linux/kernel/git/palmer/riscv-linux
Pull RISC-V updates from Palmer Dabbelt:
"This contains an assortment of RISC-V related patches that I'd like to
target for the 5.2 merge window. Most of the patches are cleanups, but
there are a handful of user-visible changes:
- The nosmp and nr_cpus command-line arguments are now supported,
which work like normal.
- The SBI console no longer installs itself as a preferred console,
we rely on standard mechanisms (/chosen, command-line, hueristics)
instead.
- sfence_remove_sfence_vma{,_asid} now pass their arguments along to
the SBI call.
- Modules now support BUG().
- A missing sfence.vma during boot has been added. This bug only
manifests during boot.
- The arch/riscv support for SiFive's L2 cache controller has been
merged, which should un-block the EDAC framework work.
I've only tested this on QEMU again, as I didn't have time to get
things running on the Unleashed. The latest master from this morning
merges in cleanly and passes the tests as well"
* tag 'riscv-for-linus-5.2-mw2' of git://git.kernel.org/pub/scm/linux/kernel/git/palmer/riscv-linux: (31 commits)
riscv: fix locking violation in page fault handler
RISC-V: sifive_l2_cache: Add L2 cache controller driver for SiFive SoCs
RISC-V: Add DT documentation for SiFive L2 Cache Controller
RISC-V: Avoid using invalid intermediate translations
riscv: Support BUG() in kernel module
riscv: Add the support for c.ebreak check in is_valid_bugaddr()
riscv: support trap-based WARN()
riscv: fix sbi_remote_sfence_vma{,_asid}.
riscv: move switch_mm to its own file
riscv: move flush_icache_{all,mm} to cacheflush.c
tty: Don't force RISCV SBI console as preferred console
RISC-V: Access CSRs using CSR numbers
RISC-V: Add interrupt related SCAUSE defines in asm/csr.h
RISC-V: Use tabs to align macro values in asm/csr.h
RISC-V: Fix minor checkpatch issues.
RISC-V: Support nr_cpus command line option.
RISC-V: Implement nosmp commandline option.
RISC-V: Add RISC-V specific arch_match_cpu_phys_id
riscv: vdso: drop unnecessary cc-ldoption
riscv: call pm_power_off from machine_halt / machine_power_off
...
The kernel module is loaded into vmalloc region which is located below
to the PAGE_OFFSET. Hence the condition, pc < PAGE_OFFSET, in the
is_valid_bugaddr() will filter out all trap exceptions triggered
by kernel module. To support BUG() in kernel module, the condition is
changed to pc < VMALLOC_START.
Signed-off-by: Vincent Chen <vincentc@andestech.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
The macro __BUG_INSN currently is defined as the "ebreak" opcode.
The is_valid_bugaddr() function compares the instruction pointed to by
$sepc with macro __BUG_INSN to check whether the current trap exception
is caused by an "ebreak" instruction. However, this check flow is possibly
erroneous because if C extension is supported, the expected trap
instruction "ebreak" is possibly translated to "c.ebreak" by the assembler.
Therefore, it requires a mechanism to distinguish the length of the
instruction in $spec and compare it to the correct trap instruction.
Signed-off-by: Vincent Chen <vincentc@andestech.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Currently, flush_icache_all is macro-expanded into a SBI call, yet no
asm/sbi.h is included in asm/cacheflush.h. This could be moved to
mm/cacheflush.c instead (SBI call will dominate performance-wise and
there is no worry to not have it inlined.
Currently, flush_icache_mm stays in kernel/smp.c, which looks like a
hack to prevent it from being compiled when CONFIG_SMP=n. It should
also be in mm/cacheflush.c.
Signed-off-by: Gary Guo <gary@garyguo.net>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
We should prefer accessing CSRs using their CSR numbers because:
1. It compiles fine with older toolchains.
2. We can use latest CSR names in #define macro names of CSR numbers
as-per RISC-V spec.
3. We can access newly added CSRs even if toolchain does not recognize
newly addes CSRs by name.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
This patch adds SCAUSE interrupt flag and SCAUSE interrupt related
defines to asm/csr.h. We also use these defines in kernel/irq.c and
express SIE/SIP flags in-terms of SCAUSE interrupt causes.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
While working on the patches, I found some minor checkpatch issues.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
If nr_cpus command line option is set, maximum possible cpu should be
set to that value.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
nosmp command line option sets max_cpus to zero. No secondary harts
will boot if this is enabled. But present cpu mask will still point to
all possible masks.
Fix present cpu mask for nosmp usecase.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
OF/DT core has a hook for architecture specific logical cpuid to hartid
mapping. By implementing this, we can pass the logical cpu id to cpu
node parsing functions.
Fix the instances where logical cpuid is expected as an argument in
of_get_cpu_node.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Towards the goal of removing cc-ldoption, it seems that --hash-style=
was added to binutils 2.17.50.0.2 in 2006. The minimal required version
of binutils for the kernel according to
Documentation/process/changes.rst is 2.20.
Link: https://gcc.gnu.org/ml/gcc/2007-01/msg01141.html
Cc: clang-built-linux@googlegroups.com
Suggested-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
This way any override of pm_power_off also affects the halt path and
we don't need additional infrastructure for it.
Also remove the pm_power_off export - at least for now we don't have
any modular drivers overriding it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
This has been helpful when debugging my pending nommu port.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Nick Kossifidis <mick@ics.forth.gr>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
HAVE_FUNCTION_GRAPH_RET_ADDR_PTR is always defined for RISC-V.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
No need to pass the hartid, and the dtb address passed is a physical
address, so don't pretend it is a kernel pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
We don't need THREAD_SIZE in asm-offsets.c as we can just calculate
the value of init_thread_union + THREAD_SIZE using cpp, just like
we do a few lines above.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Just in case an old interrupt is pending make sure we clear everything
asserted before this kernel started. Based on similar M-mode code in
opensbi.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Nick Kossifidis <mick@ics.forth.gr>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
The function of do_notify_resume called by entry.S could be entered
in loop when SIGPENDING was setted again before sret. So we must add
prevent code to make syscall restart (regs->sepc -= 0x4) or it may
re-execute unexpected instructions.
Just like in_syscall & forget_syscall used by arm.
Signed-off-by: Guo Ren <ren_guo@c-sky.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Terminating the last trace entry with ULONG_MAX is a completely pointless
exercise and none of the consumers can rely on it because it's
inconsistently implemented across architectures. In fact quite some of the
callers remove the entry and adjust stack_trace.nr_entries afterwards.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Alexander Potapenko <glider@google.com>
Cc: linux-riscv@lists.infradead.org
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Link: https://lkml.kernel.org/r/20190410103644.131061192@linutronix.de
IS_ENABLED should generally use CONFIG_ prefaced symbols and
it doesn't appear as if there is a CMODEL_MEDLOW define.
Signed-off-by: Joe Perches <joe@perches.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
The Linux RISC-V 32bit kernel is broken after we moved setup_vm() from
kernel/setup.c to mm/init.c because Linux RISC-V 32bit kernel by default
uses cmodel=medlow which results in a non-position-independent setup_vm().
This patch fixes Linux RISC-V 32bit kernel booting by:
1. Forcing cmodel=medany for mm/init.c
2. Moving remaing MM-related stuff va_pa_offset, pfn_base and
empty_zero_page from kernel/setup.c to mm/init.c
Further, the setup_vm() cannot handle GCC instrumentation for FTRACE so
we disable it for mm/init.c by not using "-pg" compiler flag.
Fixes: 6f1e9e946f ("RISC-V: Move setup_vm() to mm/init.c")
Suggested-by: Christoph Hellwig <hch@lst.de>
Suggested-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Mike Rapoport <rppt@linux.ibm.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
This contains the vast majority of the RISC-V patches for this merge
window. It includes:
* A handful of cleanups to our kernel prints, most of which are things I
should have caught the first time.
* We now provide an HWCAP that contains the ISA extensions that all
enabled processors support, as supposed to just looking at the first
enabled processor.
* We no longer spin forever waiting for all harts to boot.
* A fixmap implementation, which is coupled to some cleanups in our MM
code.
The only outstanding patches I know of right now are Vincent Chen's
patches to fix c.ebreak handling in the kernel, the v2 of which was
posted this morning. I'd like those in the MW, but I didn't want to
hold up everything else. The patch set is based on top of my last fixes
submission, but I've tested it with a conflict-free merge from v5.0.
I'm doing this rather than my "just go rebase everything" flow due to a
discussion with Linus, but if I misunderstood then just let me know and
I'll do something else. It's also the first time I've taken a PR into
my own tree, so let me know if I screwed that one up.
I've used my standard testing flow (QEMU in Fedora), but now that we're
starting to get the kernel in better shape I think it's time to impose
some more testing here -- specifically I'm going to require that patches
boot on the HiFive Unleashed because we're getting to the point where we
can actually expect that to work. I haven't done that for this tag, but
I'm going to do it for future ones.
I know the board is a bit expensive and not everyone has one, but if
I've sent you a free one and your patches break the boot then I'm going
to yell at you :). If you don't have one then please indicate how you
tested in your cover letter, and if you have a board then please add
your Tested-by to patches if they work for your testing flow.
-----BEGIN PGP SIGNATURE-----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=6gjG
-----END PGP SIGNATURE-----
Merge tag 'riscv-for-linus-5.1-mw0' of git://git.kernel.org/pub/scm/linux/kernel/git/palmer/riscv-linux
Pull RISC-V updates from Palmer Dabbelt:
"This contains the vast majority of the RISC-V patches for this merge
window. It includes:
- A handful of cleanups to our kernel prints, most of which are
things I should have caught the first time.
- We now provide an HWCAP that contains the ISA extensions that all
enabled processors support, as supposed to just looking at the
first enabled processor.
- We no longer spin forever waiting for all harts to boot.
- A fixmap implementation, which is coupled to some cleanups in our
MM code.
The only outstanding patches I know of right now are Vincent Chen's
patches to fix c.ebreak handling in the kernel, the v2 of which was
posted this morning. I'd like those in the MW, but I didn't want to
hold up everything else. The patch set is based on top of my last
fixes submission, but I've tested it with a conflict-free merge from
v5.0. I'm doing this rather than my "just go rebase everything" flow
due to a discussion with Linus, but if I misunderstood then just let
me know and I'll do something else. It's also the first time I've
taken a PR into my own tree, so let me know if I screwed that one up.
I've used my standard testing flow (QEMU in Fedora), but now that
we're starting to get the kernel in better shape I think it's time to
impose some more testing here -- specifically I'm going to require
that patches boot on the HiFive Unleashed because we're getting to the
point where we can actually expect that to work. I haven't done that
for this tag, but I'm going to do it for future ones.
I know the board is a bit expensive and not everyone has one, but if
I've sent you a free one and your patches break the boot then I'm
going to yell at you :). If you don't have one then please indicate
how you tested in your cover letter, and if you have a board then
please add your Tested-by to patches if they work for your testing
flow"
* tag 'riscv-for-linus-5.1-mw0' of git://git.kernel.org/pub/scm/linux/kernel/git/palmer/riscv-linux:
arch: riscv: fix logic error in parse_dtb
RISC-V: Assign hwcap as per comman capabilities.
RISC-V: Compare cpuid with NR_CPUS before mapping.
RISC-V: Allow hartid-to-cpuid function to fail.
RISC-V: Remove NR_CPUs check during hartid search from DT
RISC-V: Move cpuid to hartid mapping to SMP.
RISC-V: Do not wait indefinitely in __cpu_up
RISC-V: Free-up initrd in free_initrd_mem()
RISC-V: Implement compile-time fixed mappings
RISC-V: Move setup_vm() to mm/init.c
RISC-V: Move setup_bootmem() to mm/init.c
RISC-V: Setup init_mm before parse_early_param()
riscv: remove the HAVE_KPROBES option
riscv: use for_each_of_cpu_node iterator
riscv: treat cpu devicetree nodes without status as enabled
riscv: fix riscv_of_processor_hartid() comment
riscv: use pr_info and friends
riscv: add missing newlines to printk messages
Merge misc updates from Andrew Morton:
- a few misc things
- ocfs2 updates
- most of MM
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (159 commits)
tools/testing/selftests/proc/proc-self-syscall.c: remove duplicate include
proc: more robust bulk read test
proc: test /proc/*/maps, smaps, smaps_rollup, statm
proc: use seq_puts() everywhere
proc: read kernel cpu stat pointer once
proc: remove unused argument in proc_pid_lookup()
fs/proc/thread_self.c: code cleanup for proc_setup_thread_self()
fs/proc/self.c: code cleanup for proc_setup_self()
proc: return exit code 4 for skipped tests
mm,mremap: bail out earlier in mremap_to under map pressure
mm/sparse: fix a bad comparison
mm/memory.c: do_fault: avoid usage of stale vm_area_struct
writeback: fix inode cgroup switching comment
mm/huge_memory.c: fix "orig_pud" set but not used
mm/hotplug: fix an imbalance with DEBUG_PAGEALLOC
mm/memcontrol.c: fix bad line in comment
mm/cma.c: cma_declare_contiguous: correct err handling
mm/page_ext.c: fix an imbalance with kmemleak
mm/compaction: pass pgdat to too_many_isolated() instead of zone
mm: remove zone_lru_lock() function, access ->lru_lock directly
...
The VDSO is part of the kernel image and therefore the struct pages are
marked as reserved during boot.
As we install a special mapping, the actual struct pages will never be
exposed to MM via the page tables. We can therefore leave the pages
marked as reserved.
Link: http://lkml.kernel.org/r/20190114125903.24845-5-david@redhat.com
Signed-off-by: David Hildenbrand <david@redhat.com>
Acked-by: Palmer Dabbelt <palmer@sifive.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: Tobias Klauser <tklauser@distanz.ch>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Matthew Wilcox <willy@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull year 2038 updates from Thomas Gleixner:
"Another round of changes to make the kernel ready for 2038. After lots
of preparatory work this is the first set of syscalls which are 2038
safe:
403 clock_gettime64
404 clock_settime64
405 clock_adjtime64
406 clock_getres_time64
407 clock_nanosleep_time64
408 timer_gettime64
409 timer_settime64
410 timerfd_gettime64
411 timerfd_settime64
412 utimensat_time64
413 pselect6_time64
414 ppoll_time64
416 io_pgetevents_time64
417 recvmmsg_time64
418 mq_timedsend_time64
419 mq_timedreceiv_time64
420 semtimedop_time64
421 rt_sigtimedwait_time64
422 futex_time64
423 sched_rr_get_interval_time64
The syscall numbers are identical all over the architectures"
* 'timers-2038-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (36 commits)
riscv: Use latest system call ABI
checksyscalls: fix up mq_timedreceive and stat exceptions
unicore32: Fix __ARCH_WANT_STAT64 definition
asm-generic: Make time32 syscall numbers optional
asm-generic: Drop getrlimit and setrlimit syscalls from default list
32-bit userspace ABI: introduce ARCH_32BIT_OFF_T config option
compat ABI: use non-compat openat and open_by_handle_at variants
y2038: add 64-bit time_t syscalls to all 32-bit architectures
y2038: rename old time and utime syscalls
y2038: remove struct definition redirects
y2038: use time32 syscall names on 32-bit
syscalls: remove obsolete __IGNORE_ macros
y2038: syscalls: rename y2038 compat syscalls
x86/x32: use time64 versions of sigtimedwait and recvmmsg
timex: change syscalls to use struct __kernel_timex
timex: use __kernel_timex internally
sparc64: add custom adjtimex/clock_adjtime functions
time: fix sys_timer_settime prototype
time: Add struct __kernel_timex
time: make adjtime compat handling available for 32 bit
...
This patchset does:
1. Moves MM related code from kernel/setup.c to mm/init.c
2. Implements compile-time fixed mappings
Using fixed mappings, we get earlyprints even without SBI calls.
For example, we can now use kernel parameter
"earlycon=uart8250,mmio,0x10000000"
to get early prints on QEMU virt machine without using SBI calls.
The patchset is tested on QEMU virt machine.
Palmer: It looks like some of the code movement here conflicted with the
patches to move hartid handling around. As far as I can tell the only
changed code was in smp_setup_processor_id(), and I've kept the one in
smp.c.
The function early_init_dt_scan returns true if a DTB was detected.
Fixes: 8fd6e05c74 ("arch: riscv: support kernel command line forcing when no DTB passed")
Signed-off-by: Andreas Schwab <schwab@suse.de>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Paul Walmsley <paul.walmsley@sifive.com>
Tested-by: Paul Walmsley <paul.walmsley@sifive.com> # FU540 HiFive-U BBL
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Currently, we set hwcap based on first valid hart from DT. This may not
be correct always as that hart might not be current booting cpu or may
have a different capability.
Set hwcap as the capabilities supported by all possible harts with "okay"
status.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
We should never have a cpuid greater that NR_CPUS. Compare with NR_CPUS
before creating the mapping between logical and physical CPU ids. This
is also mandatory as NR_CPUS check is removed from
riscv_of_processor_hartid.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
It is perfectly okay to call riscv_hartid_to_cpuid for a hartid that is
not mapped with an CPU id. It can happen if the calling functions
retrieves the hartid from DT. However, that hartid was never brought
online by the firmware or kernel for any reasons.
No need to BUG() in the above case. A negative error return is
sufficient and the calling function should check for the return value
always.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
In non-smp configuration, hartid can be higher that NR_CPUS.
riscv_of_processor_hartid should not be compared to hartid to NR_CPUS in
that case. Moreover, this function checks all the DT properties of a
hart node. NR_CPUS comparison seems out of place.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Currently, logical CPU id to physical hartid mapping is defined for both
smp and non-smp configurations. This is not required as we need this
only for smp configuration. The mapping function can define directly
boot_cpu_hartid for non-smp use case.
The reverse mapping function i.e. hartid to cpuid can be called for any
valid but not booted harts. So it should return default cpu 0 only if it
is a boot hartid.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
In SMP path, __cpu_up waits for other CPU to come online indefinitely.
This is wrong as other CPU might be disabled in machine mode and
possible CPU is set to the cpus present in DT.
Introduce a completion variable and waits only for a second.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
This is a follow-up to the y2038 syscall patches already merged in the tip
tree. As the final 32-bit RISC-V syscall ABI is still being decided on,
this is the last chance to make a few corrections to leave out interfaces
based on 32-bit time_t along with the old off_t and rlimit types.
The series achieves this in a few steps:
- A couple of bug fixes for minor regressions I introduced
in the original series
- A couple of older patches from Yury Norov that I had never
merged in the past, these fix up the openat/open_by_handle_at and
getrlimit/setrlimit syscalls to disallow the old versions of off_t
and rlimit.
- Hiding the deprecated system calls behind an #ifdef in
include/uapi/asm-generic/unistd.h
- Change arch/riscv to drop all these ABIs.
Originally, the plan was to also leave these out on C-Sky, but that now
has a glibc port that uses the older interfaces, so we need to leave
them in place.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABCAAGBQJcdEhGAAoJEGCrR//JCVInQuUQAN+mRFzRXAqhbpb63/vYGJei
nmDqB+SoxzaIKAIGAVIdMGUoFxBrY1oyS4m6/a9lzQ9G4aSkr0PruZnUID+vIo2h
rj+3FBlB/c9nvW+NG8iEtVadlRbTmoRILCWpvgIuLNd6fwvNzP3V4uu6a1QRIMx4
aUCWQfhzv18kW1EAPIroPA1gEL2HKbhDdEuN2V0SKnsKNiWkHQeswWQFAYpLgT36
eZ+L52lh+miEdtBxycxJ5lh3KsWO4dPImh+QHONZgeB9iS8v47K0R6ONKm4NMeQV
5KW55pepUq1uQUdEU9KRrh2krMih2IJbOQoN2lvb2ao5UG6erHbj0N55RQym5gSC
+TrvP3dnqfohh9hWdHDwME+5OTeOM+8SUMRnaZBJKuywzo7W1ceLpf+KZjwlk2s5
AgEX67fKrUbtBfTgVhzlYhJLWcgSD1yt64ed5SF15c5M3JZhkK8cd50dB9pM2/YB
o9VbijkYwb2KyCNUiV3nghgiiqcROvOIO7PK6z3XFFiRm/Gn2CgNZyZa7c4+Vgrr
PM/DmDvCdFqYnqBOlV2ilCLigKGN0JgwzMXnbQU77d71Yg7Bco8e/yqSucSilp2d
lEv44extu9FINWXIqvWEjRqdSq+sNgj21VSp6Zu/GaTgNCQKac2wsAZtnQgnslko
knKwwp525fjqnJEDd1aH
=/iFA
-----END PGP SIGNATURE-----
Merge tag 'y2038-syscall-abi' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/playground into timers/2038
Pull additional syscall ABI cleanup for y2038 from Arnd Bergmann:
This is a follow-up to the y2038 syscall patches already merged in the tip
tree. As the final 32-bit RISC-V syscall ABI is still being decided on,
this is the last chance to make a few corrections to leave out interfaces
based on 32-bit time_t along with the old off_t and rlimit types.
The series achieves this in a few steps:
- A couple of bug fixes for minor regressions I introduced
in the original series
- A couple of older patches from Yury Norov that I had never
merged in the past, these fix up the openat/open_by_handle_at and
getrlimit/setrlimit syscalls to disallow the old versions of off_t
and rlimit.
- Hiding the deprecated system calls behind an #ifdef in
include/uapi/asm-generic/unistd.h
- Change arch/riscv to drop all these ABIs.
Originally, the plan was to also leave these out on C-Sky, but that now
has a glibc port that uses the older interfaces, so we need to leave
them in place.
We don't yet have an upstream glibc port for riscv, so there is no user
space for the existing ABI, and we can remove the definitions for 32-bit
time_t, off_t and struct resource and system calls based on them,
including the vdso.
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The setup_vm() is responsible for setting up initial page table hence
should be placed in mm/init.c.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
The setup_bootmem() mainly populates memblocks and does early memory
reservations. The right location for this function is mm/init.c. It
calls setup_initrd() so we move that as well.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
Reviewed-by: Mike Rapoport <rppt@linux.ibm.com>
We should setup init_mm before doing parse_early_param() in setup_arch()
to be consistent with setup_arch() of other architectures such as x86,
ARM, and ARM64.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
Use the new for_each_of_cpu_node() helper to iterate over cpu nodes
instead of open coding. Note that this will allow matching also on the
node name instead of the (for FDT) deprecated device_type property.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Follow the Linux convention and treat devicetree nodes without a status
property as enabled rather than disabled, while also allowing "ok" as a
shorthand for "okay".
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Paul Walmsley <paul.walmsley@sifive.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
The riscv_of_processor_hartid() helper returns -ENODEV when the
specified node isn't an enabled and valid RISC-V hart node.
Also drop the unnecessary parenthesis around errno defines.
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Paul Walmsley <paul.walmsley@sifive.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Use the pr_info and pr_err macros instead of printk with explicit log
levels.
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Paul Walmsley <paul.walmsley@sifive.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Add missing newline characters to printk messages.
Also replace two pr_warning with the shorter pr_warn, and fix up the
tense of one error message while at it.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
At least BBL relies on the flat binaries containing all the bytes in the
actual image to exist in the file. Before this revert the flat images
dropped the trailing zeros, which caused BBL to put its copy of the
device tree where Linux thought the BSS was, which wreaks all sorts of
havoc. Manifesting the bug is a bit subtle because BBL aligns
everything to 2MiB page boundaries, but with large enough kernels you're
almost certain to get bitten by the bug.
While moving the sections around isn't a great long-term fix, it will at
least avoid producing broken images.
This reverts commit 22e6a2e14c.
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
max_low_pfn should be pfn_size not byte_size.
Signed-off-by: Guo Ren <ren_guo@c-sky.com>
Signed-off-by: Mao Han <mao_han@c-sky.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
The cond_resched() can be used to yield the CPU resource if
CONFIG_PREEMPT is not defined. Otherwise, cond_resched() is a dummy
function. In order to avoid kernel thread occupying entire CPU,
when CONFIG_PREEMPT=y, the kernel thread needs to follow the
rescheduling mechanism like a user thread.
Signed-off-by: Vincent Chen <vincentc@andestech.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
This is sort of a mix between a new feature and a bug fix. I've managed
to screw up merging this patch set a handful of times but I think it's
OK this time around. The main new feature here is audit support for
RISC-V, with some fixes to audit-related bugs that cropped up along the
way:
* The addition of NR_syscalls into unistd.h, which is necessary for
CONFIG_FTRACE_SYSCALLS.
* The definition of CREATE_TRACE_POINTS so
__tracepoint_sys_{enter,exit} get defined.
* A fix for trace_sys_exit() so we can enable
CONFIG_HAVE_SYSCALL_TRACEPOINTS.
Define CREATE_TRACE_POINTS in order to create functions and structures
for the trace events. This is needed if HAVE_SYSCALL_TRACEPOINTS and
CONFIG_FTRACE_SYSCALLS are enabled, otherwise we get linking errors:
[..]
MODPOST vmlinux.o
kernel/trace/trace_syscalls.o: In function `.L0 ':
trace_syscalls.c:(.text+0x1152): undefined reference to `__tracepoint_sys_enter'
trace_syscalls.c:(.text+0x126c): undefined reference to `__tracepoint_sys_enter'
trace_syscalls.c:(.text+0x1328): undefined reference to `__tracepoint_sys_enter'
trace_syscalls.c:(.text+0x14aa): undefined reference to `__tracepoint_sys_enter'
trace_syscalls.c:(.text+0x1684): undefined reference to `__tracepoint_sys_exit'
trace_syscalls.c:(.text+0x17a0): undefined reference to `__tracepoint_sys_exit'
trace_syscalls.c:(.text+0x185c): undefined reference to `__tracepoint_sys_exit'
trace_syscalls.c:(.text+0x19de): undefined reference to `__tracepoint_sys_exit'
arch/riscv/kernel/ptrace.o: In function `.L0 ':
ptrace.c:(.text+0x4dc): undefined reference to `__tracepoint_sys_enter'
ptrace.c:(.text+0x632): undefined reference to `__tracepoint_sys_exit'
make: *** [Makefile:1036: vmlinux] Error 1
Signed-off-by: David Abdurachmanov <david.abdurachmanov@gmail.com>
Fixes: b78002b395b4 ("riscv: add HAVE_SYSCALL_TRACEPOINTS to Kconfig")
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
This patch adds auditing functions on entry to and exit from every system
call invocation.
Signed-off-by: David Abdurachmanov <david.abdurachmanov@gmail.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
On RISC-V (riscv) audit is supported through generic lib/audit.c.
The patch adds required arch specific definitions.
Signed-off-by: David Abdurachmanov <david.abdurachmanov@gmail.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
This patch supports dynamic generate got and plt sections mechanism on
rv32. It contains the modification as follows:
- Always enable MODULE_SECTIONS (both rv64 and rv32)
- Change the fixed size type.
This patch had been tested by following modules:
btrfs 6795991 0 - Live 0xa544b000
test_static_keys 17304 0 - Live 0xa28be000
zstd_compress 1198986 1 btrfs, Live 0xa2a25000
zstd_decompress 608112 1 btrfs, Live 0xa24e7000
lzo 8787 0 - Live 0xa2049000
xor 27461 1 btrfs, Live 0xa2041000
zram 78849 0 - Live 0xa2276000
netdevsim 55909 0 - Live 0xa202d000
tun 211534 0 - Live 0xa21b5000
fuse 566049 0 - Live 0xa25fb000
nfs_layout_flexfiles 192597 0 - Live 0xa229b000
ramoops 74895 0 - Live 0xa2019000
xfs 3973221 0 - Live 0xa507f000
libcrc32c 3053 2 btrfs,xfs, Live 0xa34af000
lzo_compress 17302 2 btrfs,lzo, Live 0xa347d000
lzo_decompress 7178 2 btrfs,lzo, Live 0xa3451000
raid6_pq 142086 1 btrfs, Live 0xa33a4000
reed_solomon 31022 1 ramoops, Live 0xa31eb000
test_bitmap 3734 0 - Live 0xa31af000
test_bpf 1588736 0 - Live 0xa2c11000
test_kmod 41161 0 - Live 0xa29f8000
test_module 1356 0 - Live 0xa299e000
test_printf 6024 0 [permanent], Live 0xa2971000
test_static_key_base 5797 1 test_static_keys, Live 0xa2931000
test_user_copy 4382 0 - Live 0xa28c9000
xxhash 70501 2 zstd_compress,zstd_decompress, Live 0xa2055000
Signed-off-by: Zong Li <zong@andestech.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Add IPI_CPU_STOP message and use it in smp_send_stop to stop other cpus,
but not itself. Mark cpu offline on reception of IPI_CPU_STOP.
Signed-off-by: Andreas Schwab <schwab@suse.de>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
CONFIG_CMDLINE_FORCE doesn't work on RISC-V when no DTB is passed into
the kernel. This is because the code that forces the kernel command
line only runs if a valid DTB is present at boot. During debugging,
it's useful to have the ability to force kernel command lines even
when no DTB is present. This patch adds support for doing so.
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: linux-riscv@lists.infradead.org
Cc: linux-kernel@vger.kernel.org (open list)
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
The objcopy only emits loadable sections when creating flat kernel
Image. To have minimal possible size of flat kernel Image, we should
have all non-loadable sections after loadable sections.
Currently, execption table section (loadable section) is after BSS
section (non-loadable section) in the RISC-V vmlinux.lds.S. This
is not optimal for having minimal flat kernel Image size hence this
patch makes BSS section as the last section in RISC-V vmlinux.lds.S.
In addition, we make BSS section aligned to 16byte instead of PAGE
aligned which further reduces flat kernel Image size by few KBs.
The flat kernel Image size of Linux-4.20-rc4 using GCC 8.2.0 is
8819980 bytes with current RISC-V vmlinux.lds.S and it reduces to
7991740 bytes with this patch applied. In summary, this patch reduces
Linux-4.20-rc4 flat kernel Image size by 809 KB.
Signed-off-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Nobody has actually used the type (VERIFY_READ vs VERIFY_WRITE) argument
of the user address range verification function since we got rid of the
old racy i386-only code to walk page tables by hand.
It existed because the original 80386 would not honor the write protect
bit when in kernel mode, so you had to do COW by hand before doing any
user access. But we haven't supported that in a long time, and these
days the 'type' argument is a purely historical artifact.
A discussion about extending 'user_access_begin()' to do the range
checking resulted this patch, because there is no way we're going to
move the old VERIFY_xyz interface to that model. And it's best done at
the end of the merge window when I've done most of my merges, so let's
just get this done once and for all.
This patch was mostly done with a sed-script, with manual fix-ups for
the cases that weren't of the trivial 'access_ok(VERIFY_xyz' form.
There were a couple of notable cases:
- csky still had the old "verify_area()" name as an alias.
- the iter_iov code had magical hardcoded knowledge of the actual
values of VERIFY_{READ,WRITE} (not that they mattered, since nothing
really used it)
- microblaze used the type argument for a debug printout
but other than those oddities this should be a total no-op patch.
I tried to fix up all architectures, did fairly extensive grepping for
access_ok() uses, and the changes are trivial, but I may have missed
something. Any missed conversion should be trivially fixable, though.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now that we have earlycon support in the SBI console driver there is no
reason to have our arch-specific early printk support. This patch set
turns on SBI earlycon support and removes the old early printk.
Noticed while building kernel-4.20.0-0.rc5.git2.1.fc30 for
Fedora 30/RISCV.
[..]
BUILDSTDERR: arch/riscv/kernel/ftrace.c: In function 'prepare_ftrace_return':
BUILDSTDERR: arch/riscv/kernel/ftrace.c:135:6: warning: unused variable 'err' [-Wunused-variable]
BUILDSTDERR: int err;
BUILDSTDERR: ^~~
[..]
Signed-off-by: David Abdurachmanov <david.abdurachmanov@gmail.com>
Fixes: e949b6db51 ("riscv/function_graph: Simplify with function_graph_enter()")
Reviewed-by: Olof Johansson <olof@lixom.net>
Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Fix of_node* refcount at various places by using of_node_put.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
The EARLY_PRINTK using SBI console calls is not required
any more because we now have RISC-V SBI support in generic
earlycon framework.
Signed-off-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
was introduced by a patch that tried to fix one bug, but by doing so created
another bug. As both bugs corrupt the output (but they do not crash the
kernel), I decided to fix the design such that it could have both bugs
fixed. The original fix, fixed time reporting of the function graph tracer
when doing a max_depth of one. This was code that can test how much the
kernel interferes with userspace. But in doing so, it could corrupt the time
keeping of the function profiler.
The issue is that the curr_ret_stack variable was being used for two
different meanings. One was to keep track of the stack pointer on the
ret_stack (shadow stack used by the function graph tracer), and the other
use case was the graph call depth. Although, the two may be closely
related, where they got updated was the issue that lead to the two different
bugs that required the two use cases to be updated differently.
The big issue with this fix is that it requires changing each architecture.
The good news is, I was able to remove a lot of code that was duplicated
within the architectures and place it into a single location. Then I could
make the fix in one place.
I pushed this code into linux-next to let it settle over a week, and before
doing so, I cross compiled all the affected architectures to make sure that
they built fine.
In the mean time, I also pulled in a patch that fixes the sched_switch
previous tasks state output, that was not actually correct.
-----BEGIN PGP SIGNATURE-----
iIoEABYIADIWIQRRSw7ePDh/lE+zeZMp5XQQmuv6qgUCW/4NPhQccm9zdGVkdEBn
b29kbWlzLm9yZwAKCRAp5XQQmuv6qnWAAQCyUIRLgYImr81eTl52lxNRsULk+aiI
U29kRFWWU0c40AEA1X9sDF0MgOItbRGfZtnHTZEousXRDaDf4Fge2kF7Egg=
=liQ0
-----END PGP SIGNATURE-----
Merge tag 'trace-v4.20-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
"While rewriting the function graph tracer, I discovered a design flaw
that was introduced by a patch that tried to fix one bug, but by doing
so created another bug.
As both bugs corrupt the output (but they do not crash the kernel), I
decided to fix the design such that it could have both bugs fixed. The
original fix, fixed time reporting of the function graph tracer when
doing a max_depth of one. This was code that can test how much the
kernel interferes with userspace. But in doing so, it could corrupt
the time keeping of the function profiler.
The issue is that the curr_ret_stack variable was being used for two
different meanings. One was to keep track of the stack pointer on the
ret_stack (shadow stack used by the function graph tracer), and the
other use case was the graph call depth. Although, the two may be
closely related, where they got updated was the issue that lead to the
two different bugs that required the two use cases to be updated
differently.
The big issue with this fix is that it requires changing each
architecture. The good news is, I was able to remove a lot of code
that was duplicated within the architectures and place it into a
single location. Then I could make the fix in one place.
I pushed this code into linux-next to let it settle over a week, and
before doing so, I cross compiled all the affected architectures to
make sure that they built fine.
In the mean time, I also pulled in a patch that fixes the sched_switch
previous tasks state output, that was not actually correct"
* tag 'trace-v4.20-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
sched, trace: Fix prev_state output in sched_switch tracepoint
function_graph: Have profiler use curr_ret_stack and not depth
function_graph: Reverse the order of pushing the ret_stack and the callback
function_graph: Move return callback before update of curr_ret_stack
function_graph: Use new curr_ret_depth to manage depth instead of curr_ret_stack
function_graph: Make ftrace_push_return_trace() static
sparc/function_graph: Simplify with function_graph_enter()
sh/function_graph: Simplify with function_graph_enter()
s390/function_graph: Simplify with function_graph_enter()
riscv/function_graph: Simplify with function_graph_enter()
powerpc/function_graph: Simplify with function_graph_enter()
parisc: function_graph: Simplify with function_graph_enter()
nds32: function_graph: Simplify with function_graph_enter()
MIPS: function_graph: Simplify with function_graph_enter()
microblaze: function_graph: Simplify with function_graph_enter()
arm64: function_graph: Simplify with function_graph_enter()
ARM: function_graph: Simplify with function_graph_enter()
x86/function_graph: Simplify with function_graph_enter()
function_graph: Create function_graph_enter() to consolidate architecture code
The function_graph_enter() function does the work of calling the function
graph hook function and the management of the shadow stack, simplifying the
work done in the architecture dependent prepare_ftrace_return().
Have riscv use the new code, and remove the shadow stack management as well as
having to set up the trace structure.
This is needed to prepare for a fix of a design bug on how the curr_ret_stack
is used.
Cc: Greentime Hu <greentime@andestech.com>
Cc: Alan Kao <alankao@andestech.com>
Cc: stable@kernel.org
Fixes: 03274a3ffb ("tracing/fgraph: Adjust fgraph depth before calling trace return callback")
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
Reviewed-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Removes the warning about an unsupported ISA when reading /proc/cpuinfo
on QEMU. The "S" extension is not being returned as it is not accessible
from userspace.
Signed-off-by: Patrick Stählin <me@packi.ch>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
This patch extends Linux RISC-V build system to build and install:
Image - Flat uncompressed kernel image
Image.gz - Flat and GZip compressed kernel image
Quiet a few bootloaders (such as Uboot, UEFI, etc) are capable of
booting flat and compressed kernel images. In case of Uboot, booting
Image or Image.gz is achieved using bootm command.
The flat and uncompressed kernel image (i.e. Image) is very useful
in pre-silicon developent and testing because we can create back-door
HEX files for RAM on FPGAs from Image.
Signed-off-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Fixes:
arch/riscv/kernel/module.c: In function 'apply_r_riscv_32_rela':
./include/linux/kern_levels.h:5:18: warning: format '%llx' expects argument of type 'long long unsigned int', but argument 3 has type 'Elf32_Addr' {aka 'unsigned int'} [-Wformat=]
arch/riscv/kernel/module.c:23:27: note: format string is defined here
arch/riscv/kernel/module.c: In function 'apply_r_riscv_pcrel_hi20_rela':
./include/linux/kern_levels.h:5:18: warning: format '%llx' expects argument of type 'long long unsigned int', but argument 3 has type 'Elf32_Addr' {aka 'unsigned int'} [-Wformat=]
arch/riscv/kernel/module.c:104:23: note: format string is defined here
arch/riscv/kernel/module.c: In function 'apply_r_riscv_hi20_rela':
./include/linux/kern_levels.h:5:18: warning: format '%llx' expects argument of type 'long long unsigned int', but argument 3 has type 'Elf32_Addr' {aka 'unsigned int'} [-Wformat=]
arch/riscv/kernel/module.c:146:23: note: format string is defined here
arch/riscv/kernel/module.c: In function 'apply_r_riscv_got_hi20_rela':
./include/linux/kern_levels.h:5:18: warning: format '%llx' expects argument of type 'long long unsigned int', but argument 3 has type 'Elf32_Addr' {aka 'unsigned int'} [-Wformat=]
arch/riscv/kernel/module.c:190:60: note: format string is defined here
arch/riscv/kernel/module.c: In function 'apply_r_riscv_call_plt_rela':
./include/linux/kern_levels.h:5:18: warning: format '%llx' expects argument of type 'long long unsigned int', but argument 3 has type 'Elf32_Addr' {aka 'unsigned int'} [-Wformat=]
arch/riscv/kernel/module.c:214:24: note: format string is defined here
arch/riscv/kernel/module.c: In function 'apply_r_riscv_call_rela':
./include/linux/kern_levels.h:5:18: warning: format '%llx' expects argument of type 'long long unsigned int', but argument 3 has type 'Elf32_Addr' {aka 'unsigned int'} [-Wformat=]
arch/riscv/kernel/module.c:236:23: note: format string is defined here
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
On the Hifive-U platform, cpu 0 is a masked cpu with less capabilities
than the other cpus. Ignore it for the purpose of determining the
hardware capabilities of the system.
Signed-off-by: Andreas Schwab <schwab@suse.de>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
This patch series now has evolved to contain several related changes.
1. Updated the assorted cleanup series by Palmer.
The original cleanup patch series can be found here.
http://lists.infradead.org/pipermail/linux-riscv/2018-August/001232.html
2. Implemented decoupling linux logical CPU ids from hart id.
Some of the work has been inspired from ARM64.
Tested on QEMU & HighFive Unleashed board with/without SMP enabled.
3. Included Anup's cleanup and IPI stat patch.
All the patch series have been combined to avoid conflicts as a lot of
common code is changed different patch sets. Atish has mostly addressed
review comments and fixed checkpatch errors from Palmer's and Anup's
series.
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
This patch set fixes up various failures in the RV32I port. The fixes
are all nominally independent, but are really only testable together
because the RV32I port fails to build without all of them. The patch
set includes:
* The removal of tishift on RV32I targets, as 128-bit integers are not
supported by the toolchain.
* The removal of swiotlb from RV32I targets, since all physical
addresses can be mapped by all hardware on all existing RV32I targets.
* The addition of ummodi3 and udivmoddi4 from an old version of GCC that
was licensed under GPLv2 as generic code, along with their use on
RV32I targets.
* A fix to our page alignment logic within ioremap for RV32I targets.
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
This patchset adds an option, CONFIG_FPU, to enable/disable floating-
point support within the kernel. The kernel's new behavior will be as
follows:
* with CONFIG_FPU=y
All FPU codes are reserved. If no FPU is found during booting, a
global flag will be set, and those functions will be bypassed with
condition check to that flag.
* with CONFIG_FPU=n
No floating-point instructions in kernel and all related settings
are excluded.
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
This export is not only not needed, but also breaks symbol versioning
due to being an undeclared assembly export.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Add a variable and a macro to describe FP registers, assuming only D is
supported. FP code is conditional on CONFIG_FPU. The FP regs and FCSR
are copied separately to avoid copying struct padding. Tested by hand and
with the gdb testsuite.
Signed-off-by: Jim Wilson <jimw@sifive.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
The RISC-V Linux port doesn't support systems that have the F extension
but don't have the D extension -- we actually don't support systems
without D either, but Alan's patch set is rectifying that soon. For now
I think we can leave this in a semi-broken state and just wait for
Alan's patch set to get merged for proper non-FPU support -- the patch
set is starting to look good, so doing something in-between doesn't seem
like it's worth the work.
I don't think it's worth fretting about support for systems with F but
not D for now: our glibc ABIs are IMAC and IMAFDC so they probably won't
end up being popular. We can always extend this in the future.
CC: Alan Kao <alankao@andestech.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
These are just hard coded in the RISC-V port, which doesn't make any
sense. We should probably be setting these from device tree entries
when they exist, but for now I think it's saner to just leave them all
as their default values.
Reviewed-by: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
This patch provides arch_show_interrupts() implementation to
show IPI stats via /proc/interrupts.
Now the contents of /proc/interrupts" will look like below:
CPU0 CPU1 CPU2 CPU3
8: 17 7 6 14 SiFive PLIC 8 virtio0
10: 10 10 9 11 SiFive PLIC 10 ttyS0
IPI0: 170 673 251 79 Rescheduling interrupts
IPI1: 1 12 27 1 Function call interrupts
Signed-off-by: Anup Patel <anup@brainfault.org>
[Atish - Fixed checkpatch errors]
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
Changes since v2:
- Remove use of IPI_CALL_WAKEUP because it's being removed
Changes since v1:
- Add stub inline show_ipi_stats() function for !CONFIG_SMP
- Make ipi_names[] dynamically sized at compile time
- Minor beautification of ipi_names[] using tabs
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Currently, /proc/cpuinfo show logical CPU ID as Hart ID which
is in-correct. This patch shows CPU ID and Hart ID separately
in /proc/cpuinfo using cpuid_to_hardid_map().
With this patch, contents of /proc/cpuinfo looks as follows:
processor : 0
hart : 1
isa : rv64imafdc
mmu : sv48
processor : 1
hart : 0
isa : rv64imafdc
mmu : sv48
processor : 2
hart : 2
isa : rv64imafdc
mmu : sv48
processor : 3
hart : 3
isa : rv64imafdc
mmu : sv48
Signed-off-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Setup the cpu_logical_map during boot. Moreover, every SBI call
and PLIC context are based on the physical hartid. Use the logical
CPU to hartid mapping to pass correct hartid to respective functions.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Currently, both Linux CPU id and hart id are same.
This is not recommended as it will lead to discontinuous CPU
indexing in Linux. Moreover, kdump kernel will run from CPU0
which would be absent if we follow existing scheme.
Implement a logical mapping between Linux CPU id and hart
id to decouple these two. Always mark the boot processor as
CPU0 and all other CPUs get the logical CPU id based on their
booting order.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
The secondary harts spin on couple of per cpu variables until both of
these are non-zero so it's not necessary to have any ordering here.
However, WRITE_ONCE should be used to avoid tearing.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
commit f1f1007644 ("mm: add new mmgrab() helper") added a
helper that we missed out on.
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
The old name was a bit odd.
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
It's a bit confusing exactly what this function does: it actually
returns the hartid of an OF processor node, failing with -1 on invalid
nodes. I've changed the name to _hartid() in order to make that a bit
more clear, as well as adding a comment.
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
[Atish: code comment formatting update]
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Currently, irq is enabled before preemption disabling happens.
If the scheduler fired right here and cpu is scheduled then it
may blow up.
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
[Atish: Commit text and code comment formatting update]
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
We shouldn't be directly passing device tree values to userspace, both
because there could be mistakes in device trees and because the kernel
doesn't support arbitrary ISAs.
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
[Atish: checkpatch fix and code comment formatting update]
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
These are just hard coded in the RISC-V port, which doesn't make any
sense. We should probably be setting these from device tree entries
when they exist, but for now I think it's saner to just leave them all
as their default values.
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
The scause is already part of pt_regs so no need to pass
scause as separate arg to do_IRQ().
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Only RV64 supports swiotlb. On RV32, it don't select the SWIOTLB.
Signed-off-by: Zong Li <zong@andestech.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
