When add one disk to array, the md_reap_sync_thread is responsible
to activate the spare and set In_sync flag for the new member in
spare_active().
But if raid1 has one member disk A, and disk B is added to the array.
Then we offline A before all the datas are synchronized from A to B,
obviously B doesn't have the latest data as A, but B is still marked
with In_sync flag.
So let's not call spare_active under the condition, otherwise B is
still showed with 'U' state which is not correct.
Signed-off-by: Guoqing Jiang <guoqing.jiang@cloud.ionos.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
When a disk is added to array, the following path is called in mdadm.
Manage_subdevs -> sysfs_freeze_array
-> Manage_add
-> sysfs_set_str(&info, NULL, "sync_action","idle")
Then from kernel side, Manage_add invokes the path (add_new_disk ->
validate_super = super_1_validate) to set In_sync flag.
Since In_sync means "device is in_sync with rest of array", and the new
added disk need to resync thread to help the synchronization of data.
And md_reap_sync_thread would call spare_active to set In_sync for the
new added disk finally. So don't set In_sync if array is in frozen.
Signed-off-by: Guoqing Jiang <guoqing.jiang@cloud.ionos.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
When the 'last' device in a RAID1 or RAID10 reports an error,
we do not mark it as failed. This would serve little purpose
as there is no risk of losing data beyond that which is obviously
lost (as there is with RAID5), and there could be other sectors
on the device which are readable, and only readable from this device.
This in general this maximises access to data.
However the current implementation also stops an admin from removing
the last device by direct action. This is rarely useful, but in many
case is not harmful and can make automation easier by removing special
cases.
Also, if an attempt to write metadata fails the device must be marked
as faulty, else an infinite loop will result, attempting to update
the metadata on all non-faulty devices.
So add 'fail_last_dev' member to 'struct mddev', then we can bypasses
the 'last disk' checks for RAID1 and RAID10, and control the behavior
per array by change sysfs node.
Signed-off-by: NeilBrown <neilb@suse.de>
[add sysfs node for fail_last_dev by Guoqing]
Signed-off-by: Guoqing Jiang <guoqing.jiang@cloud.ionos.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
Instead of linear approach to calculate power of 10, use generic int_pow()
which does it better.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
Pull percpu updates from Dennis Zhou:
"This includes changes to let percpu_ref release the backing percpu
memory earlier after it has been switched to atomic in cases where the
percpu ref is not revived.
This will help recycle percpu memory earlier in cases where the
refcounts are pinned for prolonged periods of time"
* 'for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/dennis/percpu:
percpu_ref: release percpu memory early without PERCPU_REF_ALLOW_REINIT
md: initialize percpu refcounters using PERCU_REF_ALLOW_REINIT
io_uring: initialize percpu refcounters using PERCU_REF_ALLOW_REINIT
percpu_ref: introduce PERCPU_REF_ALLOW_REINIT flag
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl0Os1seHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGtx4H/j6i482XzcGFKTBm
A7mBoQpy+kLtoUov4EtBAR62OuwI8rsahW9di37QKndPoQrczWaKBmr3De6LCdPe
v3pl3O6wBbvH5ru+qBPFX9PdNbDvimEChh7LHxmMxNQq3M+AjZAZVJyfpoiFnx35
Fbge+LZaH/k8HMwZmkMr5t9Mpkip715qKg2o9Bua6dkH0AqlcpLlC8d9a+HIVw/z
aAsyGSU8jRwhoAOJsE9bJf0acQ/pZSqmFp0rDKqeFTSDMsbDRKLGq/dgv4nW0RiW
s7xqsjb/rdcvirRj3rv9+lcTVkOtEqwk0PVdL9WOf7g4iYrb3SOIZh8ZyViaDSeH
VTS5zps=
=huBY
-----END PGP SIGNATURE-----
Merge tag 'v5.2-rc6' into for-5.3/block
Merge 5.2-rc6 into for-5.3/block, so we get the same page merge leak
fix. Otherwise we end up having conflicts with future patches between
for-5.3/block and master that touch this area. In particular, it makes
the bio_full() fix hard to backport to stable.
* tag 'v5.2-rc6': (482 commits)
Linux 5.2-rc6
Revert "iommu/vt-d: Fix lock inversion between iommu->lock and device_domain_lock"
Bluetooth: Fix regression with minimum encryption key size alignment
tcp: refine memory limit test in tcp_fragment()
x86/vdso: Prevent segfaults due to hoisted vclock reads
SUNRPC: Fix a credential refcount leak
Revert "SUNRPC: Declare RPC timers as TIMER_DEFERRABLE"
net :sunrpc :clnt :Fix xps refcount imbalance on the error path
NFS4: Only set creation opendata if O_CREAT
ARM: 8867/1: vdso: pass --be8 to linker if necessary
KVM: nVMX: reorganize initial steps of vmx_set_nested_state
KVM: PPC: Book3S HV: Invalidate ERAT when flushing guest TLB entries
habanalabs: use u64_to_user_ptr() for reading user pointers
nfsd: replace Jeff by Chuck as nfsd co-maintainer
inet: clear num_timeout reqsk_alloc()
PCI/P2PDMA: Ignore root complex whitelist when an IOMMU is present
net: mvpp2: debugfs: Add pmap to fs dump
ipv6: Default fib6_type to RTN_UNICAST when not set
net: hns3: Fix inconsistent indenting
net/af_iucv: always register net_device notifier
...
Now, there are two places need to consider about
the failure of destroy bitmap, so move the common
part between bitmap_abort and abort label.
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
Previously, we called rdev_init_wb to avoid potential data
inconsistency when array is created.
Now, we need to call the function and create mempool if a
device is added or just be flaged as "writemostly". So
mddev_create_wb_pool is introduced and called accordingly.
And for safety reason, we mark implicit GFP_NOIO allocation
scope for create mempool during mddev_suspend/mddev_resume.
And mempool should be removed conversely after remove a
member device or its's "writemostly" flag, which is done
by call mddev_destroy_wb_pool.
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
For write-behind mode, we think write IO is complete once it has
reached all the non-writemostly devices. It works fine for single
queue devices.
But for multiqueue device, if there are lots of IOs come from upper
layer, then the write-behind device could issue those IOs to different
queues, depends on the each queue's delay, so there is no guarantee
that those IOs can arrive in order.
To address the issue, we need to check the collision among write
behind IOs, we can only continue without collision, otherwise wait
for the completion of previous collisioned IO.
And WBCollision is introduced for multiqueue device which is worked
under write-behind mode.
But this patch doesn't handle below cases which could have the data
inconsistency issue as well, these cases will be handled in later
patches.
1. modify max_write_behind by write backlog node.
2. add or remove array's bitmap dynamically.
3. the change of member disk.
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
Stopping external metadata arrays during resync/recovery causes
retries, loop of interrupting and starting reconstruction, until it
hit at good moment to stop completely. While these retries
curr_mark_cnt can be small- especially on HDD drives, so subtraction
result can be smaller than 0. However it is casted to uint without
checking. As a result of it the status bar in /proc/mdstat while stopping
is strange (it jumps between 0% and 99%).
The real problem occurs here after commit 72deb455b5 ("block: remove
CONFIG_LBDAF"). Sector_div() macro has been changed, now the
divisor is casted to uint32. For db = -8 the divisior(db/32-1) becomes 0.
Check if db value can be really counted and replace these macro by
div64_u64() inline.
Signed-off-by: Mariusz Tkaczyk <mariusz.tkaczyk@intel.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
This patch fix a spelling typo and add necessary space for code.
In addition, the patch get rid of the unnecessary 'if'.
Signed-off-by: Yufen Yu <yuyufen@huawei.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Commit c42d324099
("md: return -ENODEV if rdev has no mddev assigned") changed
rdev_attr_store to return -ENODEV when rdev->mddev is NULL, now do the
same to rdev_attr_show.
Signed-off-by: Marcos Paulo de Souza <marcos.souza.org@gmail.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 or at your option any
later version you should have received a copy of the gnu general
public license for example usr src linux copying if not write to the
free software foundation inc 675 mass ave cambridge ma 02139 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 20 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190520170858.552543146@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Percpu reference counters should now be initialized with the
PERCPU_REF_ALLOW_REINIT in order to allow switching them to the
percpu mode from the atomic mode.
To make percpu_ref_switch_to_percpu() call in set_in_sync()
succeed,let's initialize percpu refcounters with the
PERCU_REF_ALLOW_REINIT flag.
Signed-off-by: Roman Gushchin <guro@fb.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Dennis Zhou <dennis@kernel.org>
Mdadm expects that setting drive as faulty will fail with -EBUSY only if
this operation will cause RAID to be failed. If this happens, it will
try to stop the array. Currently -EBUSY might also be returned if rdev
is in the middle of the removal process - for example there is a race
with mdmon that already requested the drive to be failed/removed.
If rdev does not contain mddev, return -ENODEV instead, so the caller
can distinguish between those two cases and behave accordingly.
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: Pawel Baldysiak <pawel.baldysiak@intel.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
Sparse complains that it has no external declaration, and it turns out
that it is never even used outside of md.c. So just mark it static
and drop the export.
Acked-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Song Liu <songliubraving@fb.com>
If we want to convert from a little endian format we need to cast
to a little endian type, otherwise sparse will be unhappy.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Song Liu <songliubraving@fb.com>
If we want to convert from a little endian format we need to cast
to a little endian type, otherwise sparse will be unhappy.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Song Liu <songliubraving@fb.com>
The on-disk value is little endian and we need to convert it to
native endian before storing the value in the in-core structure.
Fixes: 7564beda19 ("md-cluster/raid10: support add disk under grow mode")
Cc: <stable@vger.kernel.org> # 4.20+
Acked-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Song Liu <songliubraving@fb.com>
When doing re-add, we need to ensure rdev->mddev->pers is not NULL,
which can avoid potential NULL pointer derefence in fallowing
add_bound_rdev().
Fixes: a6da4ef85c ("md: re-add a failed disk")
Cc: Xiao Ni <xni@redhat.com>
Cc: NeilBrown <neilb@suse.com>
Cc: <stable@vger.kernel.org> # 4.4+
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: Yufen Yu <yuyufen@huawei.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
Currently support for 64-bit sector_t and blkcnt_t is optional on 32-bit
architectures. These types are required to support block device and/or
file sizes larger than 2 TiB, and have generally defaulted to on for
a long time. Enabling the option only increases the i386 tinyconfig
size by 145 bytes, and many data structures already always use
64-bit values for their in-core and on-disk data structures anyway,
so there should not be a large change in dynamic memory usage either.
Dropping this option removes a somewhat weird non-default config that
has cause various bugs or compiler warnings when actually used.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This reverts commit 5a409b4f56.
This patch has two problems.
1/ it make multiple calls to submit_bio() from inside a make_request_fn.
The bios thus submitted will be queued on current->bio_list and not
submitted immediately. As the bios are allocated from a mempool,
this can theoretically result in a deadlock - all the pool of requests
could be in various ->bio_list queues and a subsequent mempool_alloc
could block waiting for one of them to be released.
2/ It aims to handle a case when there are many concurrent flush requests.
It handles this by submitting many requests in parallel - all of which
are identical and so most of which do nothing useful.
It would be more efficient to just send one lower-level request, but
allow that to satisfy multiple upper-level requests.
Fixes: 5a409b4f56 ("MD: fix lock contention for flush bios")
Cc: <stable@vger.kernel.org> # v4.19+
Tested-by: Xiao Ni <xni@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
bio_alloc_bioset returns a bio pointer or NULL, so we can avoid storing
the returned data into a new variable.
Acked-by: Guoqing Jiang <gqjiang@suse.com>
Acked-by: Artur Paszkiewicz <artur.paszkiewicz@intel.com>
Signed-off-by: Marcos Paulo de Souza <marcos.souza.org@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pull the pending 4.21 changes for md from Shaohua.
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/shli/md:
md: fix raid10 hang issue caused by barrier
raid10: refactor common wait code from regular read/write request
md: remvoe redundant condition check
lib/raid6: add option to skip algo benchmarking
lib/raid6: sort algos in rough performance order
lib/raid6: check for assembler SSSE3 support
lib/raid6: avoid __attribute_const__ redefinition
lib/raid6: add missing include for raid6test
md: remove set but not used variable 'bi_rdev'
mempool_destroy() can handle NULL pointer correctly,
so there is no need to check NULL pointer before calling
mempool_destroy().
Signed-off-by: Chengguang Xu <cgxu519@gmx.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/md/md.c: In function 'md_integrity_add_rdev':
drivers/md/md.c:2149:24: warning:
variable 'bi_rdev' set but not used [-Wunused-but-set-variable]
It not used any more after commit
1501efadc5 ("md/raid: only permit hot-add of compatible integrity profiles")
Signed-off-by: Yue Haibing <yuehaibing@huawei.com>
Signed-off-by: Shaohua Li <shli@fb.com>
All of part_stat_* and related methods are used with preempt disabled,
so there is no need to pass cpu around to allow of them. Just call
smp_processor_id() as needed.
Suggested-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
flush_pool is leaked when flush bio size is zero
Fixes: 5a409b4f56 ("MD: fix lock contention for flush bios")
Signed-off-by: David Jeffery <djeffery@redhat.com>
Signed-off-by: Xiao Ni <xni@redhat.com>
Signed-off-by: Shaohua Li <shli@fb.com>
I noticed kmemleak report memory leak when run create/stop
md in a loop, backtrace:
[<000000001ca975e7>] mempool_create_node+0x86/0xd0
[<0000000095576bcd>] md_run+0x1057/0x1410 [md_mod]
[<000000007b45c5fc>] do_md_run+0x15/0x130 [md_mod]
[<000000001ede9ec0>] md_ioctl+0x1f49/0x25d0 [md_mod]
[<000000004142cacf>] blkdev_ioctl+0x680/0xd00
The root cause is we alloc mddev->flush_pool and
mddev->flush_bio_pool in md_run, but from do_md_stop
will not call into md_stop but __md_stop, move the
mempool_destroy to __md_stop fixes the problem for me.
The bug was introduced in 5a409b4f56, the fixes should go to
4.18+
Fixes: 5a409b4f56 ("MD: fix lock contention for flush bios")
Signed-off-by: Jack Wang <jinpu.wang@profitbricks.com>
Reviewed-by: Xiao Ni <xni@redhat.com>
Signed-off-by: Shaohua Li <shli@fb.com>
We need to continue the reshaping if it was interrupted in
original node. So original node should call resync_bitmap
in case reshaping is aborted.
Then BITMAP_NEEDS_SYNC message is broadcasted to other nodes,
node which continues the reshaping should restart reshape from
mddev->reshape_position instead of from the first beginning.
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
remove_and_add_spares is not needed if reshape is
happening in another node, because raid10_add_disk
called inside raid10_start_reshape would handle the
role changes of disk. Plus, remove_and_add_spares
can't deal with the role change due to reshape.
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
We need to change the capacity in all nodes after one node
finishs reshape. And as we did before, we can't change the
capacity directly in md_do_sync, instead, the capacity should
be only changed in update_size or received CHANGE_CAPACITY
msg.
So master node calls update_size after completes reshape in
md_reap_sync_thread, but we need to skip ops->update_size if
MD_CLOSING is set since reshaping could not be finish.
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
For clustered raid10 scenario, we need to let all the nodes
know about that a new disk is added to the array, and the
reshape caused by add new member just need to be happened in
one node, but other nodes should know about the change.
Since reshape means read data from somewhere (which is already
used by array) and write data to unused region. Obviously, it
is awful if one node is reading data from address while another
node is writing to the same address. Considering we have
implemented suspend writes in the resyncing area, so we can
just broadcast the reading address to other nodes to avoid the
trouble.
For master node, it would call reshape_request then update sb
during the reshape period. To avoid above trouble, we call
resync_info_update to send RESYNC message in reshape_request.
Then from slave node's view, it receives two type messages:
1. RESYNCING message
Slave node add the address (where master node reading data from)
to suspend list.
2. METADATA_UPDATED message
Once slave nodes know the reshaping is started in master node,
it is time to update reshape position and call start_reshape to
follow master node's step. After reshape is done, only reshape
position is need to be updated, so the majority task of reshaping
is happened on the master node.
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Commit d595567dc4 (MD: fix invalid stored role for a disk) broke linear
hotadd. Let's only fix the role for disks in raid1/10.
Based on Guoqing's original patch.
Reported-by: kernel test robot <rong.a.chen@intel.com>
Cc: Gioh Kim <gi-oh.kim@profitbricks.com>
Cc: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Commit 35bfc52187 ("md: allow metadata update while suspending.")
added support for allowing md_check_recovery() to still perform
metadata updates while the array is entering the 'suspended' state.
This is needed to allow the processes of entering the state to
complete.
Unfortunately, the patch doesn't really work. The test for
"mddev->suspended" at the start of md_check_recovery() means that the
function doesn't try to do anything at all while entering suspend.
This patch moves the code of updating the metadata while suspending to
*before* the test on mddev->suspended.
Reported-by: Jeff Mahoney <jeffm@suse.com>
Fixes: 35bfc52187 ("md: allow metadata update while suspending.")
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
If we change the number of array's device after device is removed from array,
then add the device back to array, we can see that device is added as active
role instead of spare which we expected.
Please see the below link for details:
https://marc.info/?l=linux-raid&m=153736982015076&w=2
This is caused by that we prefer to use device's previous role which is
recorded by saved_raid_disk, but we should respect the new number of
conf->raid_disks since it could be changed after device is removed.
Reported-by: Gioh Kim <gi-oh.kim@profitbricks.com>
Tested-by: Gioh Kim <gi-oh.kim@profitbricks.com>
Acked-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Pull input updates from Dmitry Torokhov:
- a new driver for Rohm BU21029 touch controller
- new bitmap APIs: bitmap_alloc, bitmap_zalloc and bitmap_free
- updates to Atmel, eeti. pxrc and iforce drivers
- assorted driver cleanups and fixes.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (57 commits)
MAINTAINERS: Add PhoenixRC Flight Controller Adapter
Input: do not use WARN() in input_alloc_absinfo()
Input: mark expected switch fall-throughs
Input: raydium_i2c_ts - use true and false for boolean values
Input: evdev - switch to bitmap API
Input: gpio-keys - switch to bitmap_zalloc()
Input: elan_i2c_smbus - cast sizeof to int for comparison
bitmap: Add bitmap_alloc(), bitmap_zalloc() and bitmap_free()
md: Avoid namespace collision with bitmap API
dm: Avoid namespace collision with bitmap API
Input: pm8941-pwrkey - add resin entry
Input: pm8941-pwrkey - abstract register offsets and event code
Input: iforce - reorganize joystick configuration lists
Input: atmel_mxt_ts - move completion to after config crc is updated
Input: atmel_mxt_ts - don't report zero pressure from T9
Input: atmel_mxt_ts - zero terminate config firmware file
Input: atmel_mxt_ts - refactor config update code to add context struct
Input: atmel_mxt_ts - config CRC may start at T71
Input: atmel_mxt_ts - remove unnecessary debug on ENOMEM
Input: atmel_mxt_ts - remove duplicate setup of ABS_MT_PRESSURE
...
Pull MD updates from Shaohua Li:
"A few MD fixes for 4.19-rc1:
- several md-cluster fixes from Guoqing
- a data corruption fix from BingJing
- other cleanups"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/shli/md:
md/raid5: fix data corruption of replacements after originals dropped
drivers/md/raid5: Do not disable irq on release_inactive_stripe_list() call
drivers/md/raid5: Use irqsave variant of atomic_dec_and_lock()
md/r5cache: remove redundant pointer bio
md-cluster: don't send msg if array is closing
md-cluster: show array's status more accurate
md-cluster: clear another node's suspend_area after the copy is finished
bitmap API (include/linux/bitmap.h) has 'bitmap' prefix for its methods.
On the other hand MD bitmap API is special case.
Adding 'md' prefix to it to avoid name space collision.
No functional changes intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Shaohua Li <shli@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The function name mentioned doesn't exist, and the code next to it
doesn't match the description either.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Add and use a new op_stat_group() function for indexing partition stat
fields rather than indexing them by rq_data_dir() or bio_data_dir().
This function works similarly to op_is_sync() in that it takes the
request::cmd_flags or bio::bi_opf flags and determines which stats
should et updated.
In addition, the second parameter to generic_start_io_acct() and
generic_end_io_acct() is now a REQ_OP rather than simply a read or
write bit and it uses op_stat_group() on the parameter to determine
the stat group.
Note that the partition in_flight counts are not part of the per-cpu
statistics and as such are not indexed via this function. It's now
indexed by op_is_write().
tj: Refreshed on top of v4.17. Updated to pass around REQ_OP.
Signed-off-by: Michael Callahan <michaelcallahan@fb.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Joshua Morris <josh.h.morris@us.ibm.com>
Cc: Philipp Reisner <philipp.reisner@linbit.com>
Cc: Matias Bjorling <mb@lightnvm.io>
Cc: Kent Overstreet <kent.overstreet@gmail.com>
Cc: Alasdair Kergon <agk@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Add a part_stat_read_accum macro to genhd.h to read and sum across
field entries. For example to sum up the number read and write
sectors completed. In addition to being ar reasonable cleanup by
itself this will make it easier to add new stat fields in the future.
tj: Refreshed on top of v4.17.
Signed-off-by: Michael Callahan <michaelcallahan@fb.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
When resync or recovery is happening in one node,
other nodes don't show the appropriate info now.
For example, when create an array in master node
without "--assume-clean", then assemble the array
in slave nodes, you can see "resync=PENDING" when
read /proc/mdstat in slave nodes. However, the info
is confusing since "PENDING" status is introduced
for start array in read-only mode.
We introduce RESYNCING_REMOTE flag to indicate that
resync thread is running in remote node. The flags
is set when node receive RESYNCING msg. And we clear
the REMOTE flag in following cases:
1. resync or recover is finished in master node,
which means slaves receive msg with both lo
and hi are set to 0.
2. node continues resync/recovery in recover_bitmaps.
3. when resync_finish is called.
Then we show accurate information in status_resync
by check REMOTE flags and with other conditions.
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Pull MD updates from Shaohua Li:
"A few fixes of MD for this merge window. Mostly bug fixes:
- raid5 stripe batch fix from Amy
- Read error handling for raid1 FailFast device from Gioh
- raid10 recovery NULL pointer dereference fix from Guoqing
- Support write hint for raid5 stripe cache from Mariusz
- Fixes for device hot add/remove from Neil and Yufen
- Improve flush bio scalability from Xiao"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/shli/md:
MD: fix lock contention for flush bios
md/raid5: Assigning NULL to sh->batch_head before testing bit R5_Overlap of a stripe
md/raid1: add error handling of read error from FailFast device
md: fix NULL dereference of mddev->pers in remove_and_add_spares()
raid5: copy write hint from origin bio to stripe
md: fix two problems with setting the "re-add" device state.
raid10: check bio in r10buf_pool_free to void NULL pointer dereference
md: fix an error code format and remove unsed bio_sector
Previously, mddev_put() had a couple different paths for freeing a
mddev, due to the fact that the kobject wasn't initialized when the
mddev was first allocated. If we move the kobject_init() to when it's
first allocated and just use kobject_add() later, we can clean all this
up.
This also removes a hack in mddev_put() to avoid freeing biosets under a
spinlock, which involved copying biosets on the stack after the reset
bioset_init() changes.
Signed-off-by: Kent Overstreet <kent.overstreet@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
There is a lock contention when there are many processes which send flush bios
to md device. eg. Create many lvs on one raid device and mkfs.xfs on each lv.
Now it just can handle flush request sequentially. It needs to wait mddev->flush_bio
to be NULL, otherwise get mddev->lock.
This patch remove mddev->flush_bio and handle flush bio asynchronously.
I did a test with command dbench -s 128 -t 300. This is the test result:
=================Without the patch============================
Operation Count AvgLat MaxLat
--------------------------------------------------
Flush 11165 167.595 5879.560
Close 107469 1.391 2231.094
LockX 384 0.003 0.019
Rename 5944 2.141 1856.001
ReadX 208121 0.003 0.074
WriteX 98259 1925.402 15204.895
Unlink 25198 13.264 3457.268
UnlockX 384 0.001 0.009
FIND_FIRST 47111 0.012 0.076
SET_FILE_INFORMATION 12966 0.007 0.065
QUERY_FILE_INFORMATION 27921 0.004 0.085
QUERY_PATH_INFORMATION 124650 0.005 5.766
QUERY_FS_INFORMATION 22519 0.003 0.053
NTCreateX 141086 4.291 2502.812
Throughput 3.7181 MB/sec (sync open) 128 clients 128 procs max_latency=15204.905 ms
=================With the patch============================
Operation Count AvgLat MaxLat
--------------------------------------------------
Flush 4500 174.134 406.398
Close 48195 0.060 467.062
LockX 256 0.003 0.029
Rename 2324 0.026 0.360
ReadX 78846 0.004 0.504
WriteX 66832 562.775 1467.037
Unlink 5516 3.665 1141.740
UnlockX 256 0.002 0.019
FIND_FIRST 16428 0.015 0.313
SET_FILE_INFORMATION 6400 0.009 0.520
QUERY_FILE_INFORMATION 17865 0.003 0.089
QUERY_PATH_INFORMATION 47060 0.078 416.299
QUERY_FS_INFORMATION 7024 0.004 0.032
NTCreateX 55921 0.854 1141.452
Throughput 11.744 MB/sec (sync open) 128 clients 128 procs max_latency=1467.041 ms
The test is done on raid1 disk with two rotational disks
V5: V4 is more complicated than the version with memory pool. So revert to the memory pool
version
V4: use address of fbio to do hash to choose free flush info.
V3:
Shaohua suggests mempool is overkill. In v3 it allocs memory during creating raid device
and uses a simple bitmap to record which resource is free.
Fix a bug from v2. It should set flush_pending to 1 at first.
V2:
Neil pointed out two problems. One is counting error problem and another is return value
when allocat memory fails.
1. counting error problem
This isn't safe. It is only safe to call rdev_dec_pending() on rdevs
that you previously called
atomic_inc(&rdev->nr_pending);
If an rdev was added to the list between the start and end of the flush,
this will do something bad.
Now it doesn't use bio_chain. It uses specified call back function for each
flush bio.
2. Returned on IO error when kmalloc fails is wrong.
I use mempool suggested by Neil in V2
3. Fixed some places pointed by Guoqing
Suggested-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Xiao Ni <xni@redhat.com>
Signed-off-by: Shaohua Li <shli@fb.com>
We met NULL pointer BUG as follow:
[ 151.760358] BUG: unable to handle kernel NULL pointer dereference at 0000000000000060
[ 151.761340] PGD 80000001011eb067 P4D 80000001011eb067 PUD 1011ea067 PMD 0
[ 151.762039] Oops: 0000 [#1] SMP PTI
[ 151.762406] Modules linked in:
[ 151.762723] CPU: 2 PID: 3561 Comm: mdadm-test Kdump: loaded Not tainted 4.17.0-rc1+ #238
[ 151.763542] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1.fc26 04/01/2014
[ 151.764432] RIP: 0010:remove_and_add_spares.part.56+0x13c/0x3a0
[ 151.765061] RSP: 0018:ffffc90001d7fcd8 EFLAGS: 00010246
[ 151.765590] RAX: 0000000000000000 RBX: ffff88013601d600 RCX: 0000000000000000
[ 151.766306] RDX: 0000000000000000 RSI: ffff88013601d600 RDI: ffff880136187000
[ 151.767014] RBP: ffff880136187018 R08: 0000000000000003 R09: 0000000000000051
[ 151.767728] R10: ffffc90001d7fed8 R11: 0000000000000000 R12: ffff88013601d600
[ 151.768447] R13: ffff8801298b1300 R14: ffff880136187000 R15: 0000000000000000
[ 151.769160] FS: 00007f2624276700(0000) GS:ffff88013ae80000(0000) knlGS:0000000000000000
[ 151.769971] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 151.770554] CR2: 0000000000000060 CR3: 0000000111aac000 CR4: 00000000000006e0
[ 151.771272] Call Trace:
[ 151.771542] md_ioctl+0x1df2/0x1e10
[ 151.771906] ? __switch_to+0x129/0x440
[ 151.772295] ? __schedule+0x244/0x850
[ 151.772672] blkdev_ioctl+0x4bd/0x970
[ 151.773048] block_ioctl+0x39/0x40
[ 151.773402] do_vfs_ioctl+0xa4/0x610
[ 151.773770] ? dput.part.23+0x87/0x100
[ 151.774151] ksys_ioctl+0x70/0x80
[ 151.774493] __x64_sys_ioctl+0x16/0x20
[ 151.774877] do_syscall_64+0x5b/0x180
[ 151.775258] entry_SYSCALL_64_after_hwframe+0x44/0xa9
For raid6, when two disk of the array are offline, two spare disks can
be added into the array. Before spare disks recovery completing,
system reboot and mdadm thinks it is ok to restart the degraded
array by md_ioctl(). Since disks in raid6 is not only_parity(),
raid5_run() will abort, when there is no PPL feature or not setting
'start_dirty_degraded' parameter. Therefore, mddev->pers is NULL.
But, mddev->raid_disks has been set and it will not be cleared when
raid5_run abort. md_ioctl() can execute cmd 'HOT_REMOVE_DISK' to
remove a disk by mdadm, which will cause NULL pointer dereference
in remove_and_add_spares() finally.
Signed-off-by: Yufen Yu <yuyufen@huawei.com>
Signed-off-by: Shaohua Li <shli@fb.com>
If "re-add" is written to the "state" file for a device
which is faulty, this has an effect similar to removing
and re-adding the device. It should take up the
same slot in the array that it previously had, and
an accelerated (e.g. bitmap-based) rebuild should happen.
The slot that "it previously had" is determined by
rdev->saved_raid_disk.
However this is not set when a device fails (only when a device
is added), and it is cleared when resync completes.
This means that "re-add" will normally work once, but may not work a
second time.
This patch includes two fixes.
1/ when a device fails, record the ->raid_disk value in
->saved_raid_disk before clearing ->raid_disk
2/ when "re-add" is written to a device for which
->saved_raid_disk is not set, fail.
I think this is suitable for stable as it can
cause re-adding a device to be forced to do a full
resync which takes a lot longer and so puts data at
more risk.
Cc: <stable@vger.kernel.org> (v4.1)
Fixes: 97f6cd39da ("md-cluster: re-add capabilities")
Signed-off-by: NeilBrown <neilb@suse.com>
Reviewed-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Device could become faulty when clustered array handling
METADATA_UPDATED msg, so we don't need to call read_rdev
for this device.
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=RVhK
-----END PGP SIGNATURE-----
Merge tag 'for-4.17/block-20180402' of git://git.kernel.dk/linux-block
Pull block layer updates from Jens Axboe:
"It's a pretty quiet round this time, which is nice. This contains:
- series from Bart, cleaning up the way we set/test/clear atomic
queue flags.
- series from Bart, fixing races between gendisk and queue
registration and removal.
- set of bcache fixes and improvements from various folks, by way of
Michael Lyle.
- set of lightnvm updates from Matias, most of it being the 1.2 to
2.0 transition.
- removal of unused DIO flags from Nikolay.
- blk-mq/sbitmap memory ordering fixes from Omar.
- divide-by-zero fix for BFQ from Paolo.
- minor documentation patches from Randy.
- timeout fix from Tejun.
- Alpha "can't write a char atomically" fix from Mikulas.
- set of NVMe fixes by way of Keith.
- bsg and bsg-lib improvements from Christoph.
- a few sed-opal fixes from Jonas.
- cdrom check-disk-change deadlock fix from Maurizio.
- various little fixes, comment fixes, etc from various folks"
* tag 'for-4.17/block-20180402' of git://git.kernel.dk/linux-block: (139 commits)
blk-mq: Directly schedule q->timeout_work when aborting a request
blktrace: fix comment in blktrace_api.h
lightnvm: remove function name in strings
lightnvm: pblk: remove some unnecessary NULL checks
lightnvm: pblk: don't recover unwritten lines
lightnvm: pblk: implement 2.0 support
lightnvm: pblk: implement get log report chunk
lightnvm: pblk: rename ppaf* to addrf*
lightnvm: pblk: check for supported version
lightnvm: implement get log report chunk helpers
lightnvm: make address conversions depend on generic device
lightnvm: add support for 2.0 address format
lightnvm: normalize geometry nomenclature
lightnvm: complete geo structure with maxoc*
lightnvm: add shorten OCSSD version in geo
lightnvm: add minor version to generic geometry
lightnvm: simplify geometry structure
lightnvm: pblk: refactor init/exit sequences
lightnvm: Avoid validation of default op value
lightnvm: centralize permission check for lightnvm ioctl
...
This patch has been generated as follows:
for verb in set_unlocked clear_unlocked set clear; do
replace-in-files queue_flag_${verb} blk_queue_flag_${verb%_unlocked} \
$(git grep -lw queue_flag_${verb} drivers block/bsg*)
done
Except for protecting all queue flag changes with the queue lock
this patch does not change any functionality.
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: Shaohua Li <shli@fb.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Remove the disk, partition and bdi sysfs attributes before cleaning up
the request queue associated with the disk.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Joseph Qi <joseph.qi@linux.alibaba.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Cc: Shaohua Li <shli@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
There is a potential deadlock if mount/umount happens when
raid5_finish_reshape() tries to grow the size of emulated disk.
How the deadlock happens?
1) The raid5 resync thread finished reshape (expanding array).
2) The mount or umount thread holds VFS sb->s_umount lock and tries to
write through critical data into raid5 emulated block device. So it
waits for raid5 kernel thread handling stripes in order to finish it
I/Os.
3) In the routine of raid5 kernel thread, md_check_recovery() will be
called first in order to reap the raid5 resync thread. That is,
raid5_finish_reshape() will be called. In this function, it will try
to update conf and call VFS revalidate_disk() to grow the raid5
emulated block device. It will try to acquire VFS sb->s_umount lock.
The raid5 kernel thread cannot continue, so no one can handle mount/
umount I/Os (stripes). Once the write-through I/Os cannot be finished,
mount/umount will not release sb->s_umount lock. The deadlock happens.
The raid5 kernel thread is an emulated block device. It is responible to
handle I/Os (stripes) from upper layers. The emulated block device
should not request any I/Os on itself. That is, it should not call VFS
layer functions. (If it did, it will try to acquire VFS locks to
guarantee the I/Os sequence.) So we have the resync thread to send
resync I/O requests and to wait for the results.
For solving this potential deadlock, we can put the size growth of the
emulated block device as the final step of reshape thread.
2017/12/29:
Thanks to Guoqing Jiang <gqjiang@suse.com>,
we confirmed that there is the same deadlock issue in raid10. It's
reproducible and can be fixed by this patch. For raid10.c, we can remove
the similar code to prevent deadlock as well since they has been called
before.
Reported-by: Alex Wu <alexwu@synology.com>
Reviewed-by: Alex Wu <alexwu@synology.com>
Reviewed-by: Chung-Chiang Cheng <cccheng@synology.com>
Signed-off-by: BingJing Chang <bingjingc@synology.com>
Signed-off-by: Shaohua Li <sh.li@alibaba-inc.com>
The locking protocols in md assume that a device will
never be removed from an array during resync/recovery/reshape.
When that isn't happening, rcu or reconfig_mutex is needed
to protect an rdev pointer while taking a refcount. When
it is happening, that protection isn't needed.
Unfortunately there are cases were remove_and_add_spares() is
called when recovery might be happening: is state_store(),
slot_store() and hot_remove_disk().
In each case, this is just an optimization, to try to expedite
removal from the personality so the device can be removed from
the array. If resync etc is happening, we just have to wait
for md_check_recover to find a suitable time to call
remove_and_add_spares().
This optimization and not essential so it doesn't
matter if it fails.
So change remove_and_add_spares() to abort early if
resync/recovery/reshape is happening, unless it is called
from md_check_recovery() as part of a newly started recovery.
The parameter "this" is only NULL when called from
md_check_recovery() so when it is NULL, there is no need to abort.
As this can result in a NULL dereference, the fix is suitable
for -stable.
cc: yuyufen <yuyufen@huawei.com>
Cc: Tomasz Majchrzak <tomasz.majchrzak@intel.com>
Fixes: 8430e7e0af ("md: disconnect device from personality before trying to remove it.")
Cc: stable@ver.kernel.org (v4.8+)
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <sh.li@alibaba-inc.com>
If no metadata devices are configured on raid1/4/5/6/10
(e.g. via dm-raid), md_write_start() unconditionally waits
for superblocks to be written thus deadlocking.
Fix introduces mddev->has_superblocks bool, defines it in md_run()
and checks for it in md_write_start() to conditionally avoid waiting.
Once on it, check for non-existing superblocks in md_super_write().
Link: https://bugzilla.kernel.org/show_bug.cgi?id=198647
Fixes: cc27b0c78c ("md: fix deadlock between mddev_suspend() and md_write_start()")
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Shaohua Li <sh.li@alibaba-inc.com>
This is the mindless scripted replacement of kernel use of POLL*
variables as described by Al, done by this script:
for V in IN OUT PRI ERR RDNORM RDBAND WRNORM WRBAND HUP RDHUP NVAL MSG; do
L=`git grep -l -w POLL$V | grep -v '^t' | grep -v /um/ | grep -v '^sa' | grep -v '/poll.h$'|grep -v '^D'`
for f in $L; do sed -i "-es/^\([^\"]*\)\(\<POLL$V\>\)/\\1E\\2/" $f; done
done
with de-mangling cleanups yet to come.
NOTE! On almost all architectures, the EPOLL* constants have the same
values as the POLL* constants do. But they keyword here is "almost".
For various bad reasons they aren't the same, and epoll() doesn't
actually work quite correctly in some cases due to this on Sparc et al.
The next patch from Al will sort out the final differences, and we
should be all done.
Scripted-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull MD updates from Shaohua Li:
"Some small fixes for MD:
- fix raid5-cache potential problems if raid5 cache isn't fully
recovered
- fix a wait-within-wait warning in raid1/10
- make raid5-PPL support disks with writeback cache enabled"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/shli/md:
raid5-ppl: PPL support for disks with write-back cache enabled
md/r5cache: print more info of log recovery
md/raid1,raid10: silence warning about wait-within-wait
md: introduce new personality funciton start()
Pull poll annotations from Al Viro:
"This introduces a __bitwise type for POLL### bitmap, and propagates
the annotations through the tree. Most of that stuff is as simple as
'make ->poll() instances return __poll_t and do the same to local
variables used to hold the future return value'.
Some of the obvious brainos found in process are fixed (e.g. POLLIN
misspelled as POLL_IN). At that point the amount of sparse warnings is
low and most of them are for genuine bugs - e.g. ->poll() instance
deciding to return -EINVAL instead of a bitmap. I hadn't touched those
in this series - it's large enough as it is.
Another problem it has caught was eventpoll() ABI mess; select.c and
eventpoll.c assumed that corresponding POLL### and EPOLL### were
equal. That's true for some, but not all of them - EPOLL### are
arch-independent, but POLL### are not.
The last commit in this series separates userland POLL### values from
the (now arch-independent) kernel-side ones, converting between them
in the few places where they are copied to/from userland. AFAICS, this
is the least disruptive fix preserving poll(2) ABI and making epoll()
work on all architectures.
As it is, it's simply broken on sparc - try to give it EPOLLWRNORM and
it will trigger only on what would've triggered EPOLLWRBAND on other
architectures. EPOLLWRBAND and EPOLLRDHUP, OTOH, are never triggered
at all on sparc. With this patch they should work consistently on all
architectures"
* 'misc.poll' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (37 commits)
make kernel-side POLL... arch-independent
eventpoll: no need to mask the result of epi_item_poll() again
eventpoll: constify struct epoll_event pointers
debugging printk in sg_poll() uses %x to print POLL... bitmap
annotate poll(2) guts
9p: untangle ->poll() mess
->si_band gets POLL... bitmap stored into a user-visible long field
ring_buffer_poll_wait() return value used as return value of ->poll()
the rest of drivers/*: annotate ->poll() instances
media: annotate ->poll() instances
fs: annotate ->poll() instances
ipc, kernel, mm: annotate ->poll() instances
net: annotate ->poll() instances
apparmor: annotate ->poll() instances
tomoyo: annotate ->poll() instances
sound: annotate ->poll() instances
acpi: annotate ->poll() instances
crypto: annotate ->poll() instances
block: annotate ->poll() instances
x86: annotate ->poll() instances
...
In order to provide data consistency with PPL for disks with write-back
cache enabled all data has to be flushed to disks before next PPL
entry. The disks to be flushed are marked in the bitmap. It's modified
under a mutex and it's only read after PPL io unit is submitted.
A limitation of 64 disks in the array has been introduced to keep data
structures and implementation simple. RAID5 arrays with so many disks are
not likely due to high risk of multiple disks failure. Such restriction
should not be a real life limitation.
With write-back cache disabled next PPL entry is submitted when data write
for current one completes. Data flush defers next log submission so trigger
it when there are no stripes for handling found.
As PPL assures all data is flushed to disk at request completion, just
acknowledge flush request when PPL is enabled.
Signed-off-by: Tomasz Majchrzak <tomasz.majchrzak@intel.com>
Signed-off-by: Shaohua Li <sh.li@alibaba-inc.com>
In do_md_run(), md threads should not wake up until the array is fully
initialized in md_run(). However, in raid5_run(), raid5-cache may wake
up mddev->thread to flush stripes that need to be written back. This
design doesn't break badly right now. But it could lead to bad bug in
the future.
This patch tries to resolve this problem by splitting start up work
into two personality functions, run() and start(). Tasks that do not
require the md threads should go into run(), while task that require
the md threads go into start().
r5l_load_log() is moved to raid5_start(), so it is not called until
the md threads are started in do_md_run().
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Shaohua Li <shli@fb.com>
There is a small window near the end of md_do_sync where mddev->curr_resync
can be equal to MaxSector.
If status_resync is called during this window, the resulting /proc/mdstat
output contains a HUGE number of = signs due to the very large curr_resync:
Personalities : [raid1]
md123 : active raid1 sdd3[2] sdb3[0]
204736 blocks super 1.0 [2/1] [U_]
[=====================================================================
... (82 MB more) ...
================>] recovery =429496729.3% (9223372036854775807/204736)
finish=0.2min speed=12796K/sec
bitmap: 0/1 pages [0KB], 65536KB chunk
Modify status_resync to ensure the resync variable doesn't exceed
the array's max_sectors.
Signed-off-by: Nate Dailey <nate.dailey@stratus.com>
Acked-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Pull more block layer updates from Jens Axboe:
"A followup pull request, with some parts that either needed a bit more
testing before going in, merge sync, or just later arriving fixes.
This contains:
- Timer related updates from Kees. These were purposefully delayed
since I didn't want to pull in a later v4.14-rc tag to my block
tree.
- ide-cd prep sense buffer fix from Bart. Also delayed, as not to
clash with the late fix we put into 4.14-rc.
- Small BFQ updates series from Luca and Paolo.
- Single nvmet fix from James, fixing a non-functional case there.
- Bio fast clone fix from Michael, which made bcache return the wrong
data for some cases.
- Legacy IO path regression hang fix from Ming"
* 'for-linus' of git://git.kernel.dk/linux-block:
bio: ensure __bio_clone_fast copies bi_partno
nvmet_fc: fix better length checking
block: wake up all tasks blocked in get_request()
block, bfq: move debug blkio stats behind CONFIG_DEBUG_BLK_CGROUP
block, bfq: update blkio stats outside the scheduler lock
block, bfq: add missing invocations of bfqg_stats_update_io_add/remove
doc, block, bfq: update max IOPS sustainable with BFQ
ide: Make ide_cdrom_prep_fs() initialize the sense buffer pointer
md: Convert timers to use timer_setup()
block: swim3: Convert timers to use timer_setup()
block/aoe: Convert timers to use timer_setup()
amifloppy: Convert timers to use timer_setup()
block/floppy: Convert callback to pass timer_list
Summary of modules changes for the 4.15 merge window:
- Treewide module_param_call() cleanup, fix up set/get function
prototype mismatches, from Kees Cook
- Minor code cleanups
Signed-off-by: Jessica Yu <jeyu@kernel.org>
-----BEGIN PGP SIGNATURE-----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=c8vb
-----END PGP SIGNATURE-----
Merge tag 'modules-for-v4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/jeyu/linux
Pull module updates from Jessica Yu:
"Summary of modules changes for the 4.15 merge window:
- treewide module_param_call() cleanup, fix up set/get function
prototype mismatches, from Kees Cook
- minor code cleanups"
* tag 'modules-for-v4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/jeyu/linux:
module: Do not paper over type mismatches in module_param_call()
treewide: Fix function prototypes for module_param_call()
module: Prepare to convert all module_param_call() prototypes
kernel/module: Delete an error message for a failed memory allocation in add_module_usage()
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Kent Overstreet <kent.overstreet@gmail.com>
Cc: Shaohua Li <shli@kernel.org>
Cc: Alasdair Kergon <agk@redhat.com>
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: dm-devel@redhat.com
Cc: linux-bcache@vger.kernel.org
Cc: linux-raid@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Michael Lyle <mlyle@lyle.org>
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pull MD update from Shaohua Li:
"This update mostly includes bug fixes:
- md-cluster now supports raid10 from Guoqing
- raid5 PPL fixes from Artur
- badblock regression fix from Bo
- suspend hang related fixes from Neil
- raid5 reshape fixes from Neil
- raid1 freeze deadlock fix from Nate
- memleak fixes from Zdenek
- bitmap related fixes from Me and Tao
- other fixes and cleanups"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/shli/md: (33 commits)
md: free unused memory after bitmap resize
md: release allocated bitset sync_set
md/bitmap: clear BITMAP_WRITE_ERROR bit before writing it to sb
md: be cautious about using ->curr_resync_completed for ->recovery_offset
badblocks: fix wrong return value in badblocks_set if badblocks are disabled
md: don't check MD_SB_CHANGE_CLEAN in md_allow_write
md-cluster: update document for raid10
md: remove redundant variable q
raid1: remove obsolete code in raid1_write_request
md-cluster: Use a small window for raid10 resync
md-cluster: Suspend writes in RAID10 if within range
md-cluster/raid10: set "do_balance = 0" if area is resyncing
md: use lockdep_assert_held
raid1: prevent freeze_array/wait_all_barriers deadlock
md: use TASK_IDLE instead of blocking signals
md: remove special meaning of ->quiesce(.., 2)
md: allow metadata update while suspending.
md: use mddev_suspend/resume instead of ->quiesce()
md: move suspend_hi/lo handling into core md code
md: don't call bitmap_create() while array is quiesced.
...
Patch fixes kmemleak on md_stop() path used likely only by dm-raid wrapper.
Code of md is using mddev_put() where both bitsets are released however this
freeing is not shared.
Also set NULL to bio_set and sync_set pointers just like mddev_put is
doing.
Signed-off-by: Zdenek Kabelac <zkabelac@redhat.com>
Signed-off-by: Shaohua Li <shli@fb.com>
The ->recovery_offset shows how much of a non-InSync device is actually
in sync - how much has been recoveryed.
When performing a recovery, ->curr_resync and ->curr_resync_completed
follow the device address being recovered and so can be used to update
->recovery_offset.
When performing a reshape, ->curr_resync* might follow the device
addresses (raid5) or might follow array addresses (raid10), so cannot
in general be used to set ->recovery_offset. When reshaping backwards,
->curre_resync* measures from the *end* of the array-or-device, so is
particularly unhelpful.
So change the common code in md.c to only use ->curr_resync_complete
for the simple recovery case, and add code to raid5.c to update
->recovery_offset during a forwards reshape.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Only MD_SB_CHANGE_PENDING should be used to wait for transition from
clean to dirty. Checking also MD_SB_CHANGE_CLEAN is unnecessary and can
race with e.g. md_do_sync(). This sporadically causes a hang when
changing consistency policy during resync:
INFO: task mdadm:6183 blocked for more than 30 seconds.
Not tainted 4.14.0-rc3+ #391
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
mdadm D12752 6183 6022 0x00000000
Call Trace:
__schedule+0x93f/0x990
schedule+0x6b/0x90
md_allow_write+0x100/0x130 [md_mod]
? do_wait_intr_irq+0x90/0x90
resize_stripes+0x3a/0x5b0 [raid456]
? kernfs_fop_write+0xbe/0x180
raid5_change_consistency_policy+0xa6/0x200 [raid456]
consistency_policy_store+0x2e/0x70 [md_mod]
md_attr_store+0x90/0xc0 [md_mod]
sysfs_kf_write+0x42/0x50
kernfs_fop_write+0x119/0x180
__vfs_write+0x28/0x110
? rcu_sync_lockdep_assert+0x12/0x60
? __sb_start_write+0x15a/0x1c0
? vfs_write+0xa3/0x1a0
vfs_write+0xb4/0x1a0
SyS_write+0x49/0xa0
entry_SYSCALL_64_fastpath+0x18/0xad
Fixes: 2214c260c7 ("md: don't return -EAGAIN in md_allow_write for external metadata arrays")
Cc: <stable@vger.kernel.org>
Signed-off-by: Artur Paszkiewicz <artur.paszkiewicz@intel.com>
Signed-off-by: Shaohua Li <shli@fb.com>
The '2' argument means "wake up anything that is waiting".
This is an inelegant part of the design and was added
to help support management of suspend_lo/suspend_hi setting.
Now that suspend_lo/hi is managed in mddev_suspend/resume,
that need is gone.
These is still a couple of places where we call 'quiesce'
with an argument of '2', but they can safely be changed to
call ->quiesce(.., 1); ->quiesce(.., 0) which
achieve the same result at the small cost of pausing IO
briefly.
This removes a small "optimization" from suspend_{hi,lo}_store,
but it isn't clear that optimization served a useful purpose.
The code now is a lot clearer.
Suggested-by: Shaohua Li <shli@kernel.org>
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
There are various deadlocks that can occur
when a thread holds reconfig_mutex and calls
->quiesce(mddev, 1).
As some write request block waiting for
metadata to be updated (e.g. to record device
failure), and as the md thread updates the metadata
while the reconfig mutex is held, holding the mutex
can stop write requests completing, and this prevents
->quiesce(mddev, 1) from completing.
->quiesce() is now usually called from mddev_suspend(),
and it is always called with reconfig_mutex held. So
at this time it is safe for the thread to update metadata
without explicitly taking the lock.
So add 2 new flags, one which says the unlocked updates is
allowed, and one which ways it is happening. Then allow it
while the quiesce completes, and then wait for it to finish.
Reported-and-tested-by: Xiao Ni <xni@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
mddev_suspend() is a more general interface than
calling ->quiesce() and is so more extensible. A
future patch will make use of this.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
responding to ->suspend_lo and ->suspend_hi is similar
to responding to ->suspended. It is best to wait in
the common core code without incrementing ->active_io.
This allows mddev_suspend()/mddev_resume() to work while
requests are waiting for suspend_lo/hi to change.
This is will be important after a subsequent patch
which uses mddev_suspend() to synchronize updating for
suspend_lo/hi.
So move the code for testing suspend_lo/hi out of raid1.c
and raid5.c, and place it in md.c
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
bitmap_create() allocates memory with GFP_KERNEL and
so can wait for IO.
If called while the array is quiesced, it could wait indefinitely
for write out to the array - deadlock.
So call bitmap_create() before quiescing the array.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Most often mddev_suspend() is called with
reconfig_mutex held. Make this a requirement in
preparation a subsequent patch. Also require
reconfig_mutex to be held for mddev_resume(),
partly for symmetry and partly to guarantee
no races with incr/decr of mddev->suspend.
Taking the mutex in r5c_disable_writeback_async() is
a little tricky as this is called from a work queue
via log->disable_writeback_work, and flush_work()
is called on that while holding ->reconfig_mutex.
If the work item hasn't run before flush_work()
is called, the work function will not be able to
get the mutex.
So we use mddev_trylock() inside the wait_event() call, and have that
abort when conf->log is set to NULL, which happens before
flush_work() is called.
We wait in mddev->sb_wait and ensure this is woken
when any of the conditions change. This requires
waking mddev->sb_wait in mddev_unlock(). This is only
like to trigger extra wake_ups of threads that needn't
be woken when metadata is being written, and that
doesn't happen often enough that the cost would be
noticeable.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Having both a bitmap and a journal is pointless.
Attempting to do so can corrupt the bitmap if the journal
replay happens before the bitmap is initialized.
Rather than try to avoid this corruption, simply
refuse to allow arrays with both a bitmap and a journal.
So:
- if raid5_run sees both are present, fail.
- if adding a bitmap finds a journal is present, fail
- if adding a journal finds a bitmap is present, fail.
Cc: stable@vger.kernel.org (4.10+)
Signed-off-by: NeilBrown <neilb@suse.com>
Tested-by: Joshua Kinard <kumba@gentoo.org>
Acked-by: Joshua Kinard <kumba@gentoo.org>
Signed-off-by: Shaohua Li <shli@fb.com>
Several function prototypes for the set/get functions defined by
module_param_call() have a slightly wrong argument types. This fixes
those in an effort to clean up the calls when running under type-enforced
compiler instrumentation for CFI. This is the result of running the
following semantic patch:
@match_module_param_call_function@
declarer name module_param_call;
identifier _name, _set_func, _get_func;
expression _arg, _mode;
@@
module_param_call(_name, _set_func, _get_func, _arg, _mode);
@fix_set_prototype
depends on match_module_param_call_function@
identifier match_module_param_call_function._set_func;
identifier _val, _param;
type _val_type, _param_type;
@@
int _set_func(
-_val_type _val
+const char * _val
,
-_param_type _param
+const struct kernel_param * _param
) { ... }
@fix_get_prototype
depends on match_module_param_call_function@
identifier match_module_param_call_function._get_func;
identifier _val, _param;
type _val_type, _param_type;
@@
int _get_func(
-_val_type _val
+char * _val
,
-_param_type _param
+const struct kernel_param * _param
) { ... }
Two additional by-hand changes are included for places where the above
Coccinelle script didn't notice them:
drivers/platform/x86/thinkpad_acpi.c
fs/lockd/svc.c
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Jessica Yu <jeyu@kernel.org>
Please do not apply this to mainline directly, instead please re-run the
coccinelle script shown below and apply its output.
For several reasons, it is desirable to use {READ,WRITE}_ONCE() in
preference to ACCESS_ONCE(), and new code is expected to use one of the
former. So far, there's been no reason to change most existing uses of
ACCESS_ONCE(), as these aren't harmful, and changing them results in
churn.
However, for some features, the read/write distinction is critical to
correct operation. To distinguish these cases, separate read/write
accessors must be used. This patch migrates (most) remaining
ACCESS_ONCE() instances to {READ,WRITE}_ONCE(), using the following
coccinelle script:
----
// Convert trivial ACCESS_ONCE() uses to equivalent READ_ONCE() and
// WRITE_ONCE()
// $ make coccicheck COCCI=/home/mark/once.cocci SPFLAGS="--include-headers" MODE=patch
virtual patch
@ depends on patch @
expression E1, E2;
@@
- ACCESS_ONCE(E1) = E2
+ WRITE_ONCE(E1, E2)
@ depends on patch @
expression E;
@@
- ACCESS_ONCE(E)
+ READ_ONCE(E)
----
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: davem@davemloft.net
Cc: linux-arch@vger.kernel.org
Cc: mpe@ellerman.id.au
Cc: shuah@kernel.org
Cc: snitzer@redhat.com
Cc: thor.thayer@linux.intel.com
Cc: tj@kernel.org
Cc: viro@zeniv.linux.org.uk
Cc: will.deacon@arm.com
Link: http://lkml.kernel.org/r/1508792849-3115-19-git-send-email-paulmck@linux.vnet.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Motivated by the desire to illiminate the imprecise nature of
DM-specific patches being unnecessarily sent to both the MD maintainer
and mailing-list. Which is born out of the fact that DM files also
reside in drivers/md/
Now all MD-specific files in drivers/md/ start with either "raid" or
"md-" and the MAINTAINERS file has been updated accordingly.
Shaohua: don't change module name
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Since commit 4ad23a9764 ("MD: use per-cpu counter for writes_pending"),
the wait_queue is only got invoked if THREAD_WAKEUP is not set previously.
With above change, I can see process_metadata_update could always hang on
the wait queue, because mddev->thread could stay on 'D' status and the
THREAD_WAKEUP flag is not cleared since there are lots of place to wake up
mddev->thread. Then deadlock happened as follows:
linux175:~ # ps aux|grep md|grep D
root 20117 0.0 0.0 0 0 ? D 03:45 0:00 [md0_raid1]
root 20125 0.0 0.0 0 0 ? D 03:45 0:00 [md0_cluster_rec]
linux175:~ # cat /proc/20117/stack
[<ffffffffa0635604>] dlm_lock_sync+0x94/0xd0 [md_cluster]
[<ffffffffa0635674>] lock_token+0x34/0xd0 [md_cluster]
[<ffffffffa0635804>] metadata_update_start+0x64/0x110 [md_cluster]
[<ffffffffa04d985b>] md_update_sb.part.58+0x9b/0x860 [md_mod]
[<ffffffffa04da035>] md_update_sb+0x15/0x30 [md_mod]
[<ffffffffa04dc066>] md_check_recovery+0x266/0x490 [md_mod]
[<ffffffffa06450e2>] raid1d+0x42/0x810 [raid1]
[<ffffffffa04d2252>] md_thread+0x122/0x150 [md_mod]
[<ffffffff81091741>] kthread+0x101/0x140
linux175:~ # cat /proc/20125/stack
[<ffffffffa0636679>] recv_daemon+0x3f9/0x5c0 [md_cluster]
[<ffffffffa04d2252>] md_thread+0x122/0x150 [md_mod]
[<ffffffff81091741>] kthread+0x101/0x140
So let's revert the part of code in the commit to resovle the problem since
we can't get lots of benefits of previous change.
Fixes: 4ad23a9764 ("MD: use per-cpu counter for writes_pending")
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
A recent patch aimed to cause md_write_start() to fail (rather than
block) when the mddev was suspending, so as to avoid deadlocks.
Unfortunately the test in wait_event() was wrong, and it didn't change
behaviour at all.
We wait_event() must wait until the metadata is written OR the array is
suspending.
Fixes: cc27b0c78c ("md: fix deadlock between mddev_suspend() and md_write_start()")
Cc: stable@vger.kernel.org
Reported-by: Xiao Ni <xni@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
md_submit_flush_data calls pers->make_request, which missed the suspend check.
Fix it with the new md_handle_request API.
Reported-by: Nate Dailey <nate.dailey@stratus.com>
Tested-by: Nate Dailey <nate.dailey@stratus.com>
Fix: cc27b0c78c79(md: fix deadlock between mddev_suspend() and md_write_start())
Cc: stable@vger.kernel.org
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
With commit cc27b0c78c, pers->make_request could bail out without handling
the bio. If that happens, we should retry. The commit fixes md_make_request
but not other call sites. Separate the request handling part, so other call
sites can use it.
Reported-by: Nate Dailey <nate.dailey@stratus.com>
Fix: cc27b0c78c79(md: fix deadlock between mddev_suspend() and md_write_start())
Cc: stable@vger.kernel.org
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Pull MD updates from Shaohua Li:
"This update mainly fixes bugs:
- Make raid5 ppl support several ppl from Pawel
- Several raid5-cache bug fixes from Song
- Bitmap fixes from Neil and Me
- One raid1/10 regression fix since 4.12 from Me
- Other small fixes and cleanup"
* tag 'md/4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shli/md:
md/bitmap: disable bitmap_resize for file-backed bitmaps.
raid5-ppl: Recovery support for multiple partial parity logs
md: Runtime support for multiple ppls
md/raid0: attach correct cgroup info in bio
lib/raid6: align AVX512 constants to 512 bits, not bytes
raid5: remove raid5_build_block
md/r5cache: call mddev_lock/unlock() in r5c_journal_mode_show
md: replace seq_release_private with seq_release
md: notify about new spare disk in the container
md/raid1/10: reset bio allocated from mempool
md/raid5: release/flush io in raid5_do_work()
md/bitmap: copy correct data for bitmap super
Pull block layer updates from Jens Axboe:
"This is the first pull request for 4.14, containing most of the code
changes. It's a quiet series this round, which I think we needed after
the churn of the last few series. This contains:
- Fix for a registration race in loop, from Anton Volkov.
- Overflow complaint fix from Arnd for DAC960.
- Series of drbd changes from the usual suspects.
- Conversion of the stec/skd driver to blk-mq. From Bart.
- A few BFQ improvements/fixes from Paolo.
- CFQ improvement from Ritesh, allowing idling for group idle.
- A few fixes found by Dan's smatch, courtesy of Dan.
- A warning fixup for a race between changing the IO scheduler and
device remova. From David Jeffery.
- A few nbd fixes from Josef.
- Support for cgroup info in blktrace, from Shaohua.
- Also from Shaohua, new features in the null_blk driver to allow it
to actually hold data, among other things.
- Various corner cases and error handling fixes from Weiping Zhang.
- Improvements to the IO stats tracking for blk-mq from me. Can
drastically improve performance for fast devices and/or big
machines.
- Series from Christoph removing bi_bdev as being needed for IO
submission, in preparation for nvme multipathing code.
- Series from Bart, including various cleanups and fixes for switch
fall through case complaints"
* 'for-4.14/block' of git://git.kernel.dk/linux-block: (162 commits)
kernfs: checking for IS_ERR() instead of NULL
drbd: remove BIOSET_NEED_RESCUER flag from drbd_{md_,}io_bio_set
drbd: Fix allyesconfig build, fix recent commit
drbd: switch from kmalloc() to kmalloc_array()
drbd: abort drbd_start_resync if there is no connection
drbd: move global variables to drbd namespace and make some static
drbd: rename "usermode_helper" to "drbd_usermode_helper"
drbd: fix race between handshake and admin disconnect/down
drbd: fix potential deadlock when trying to detach during handshake
drbd: A single dot should be put into a sequence.
drbd: fix rmmod cleanup, remove _all_ debugfs entries
drbd: Use setup_timer() instead of init_timer() to simplify the code.
drbd: fix potential get_ldev/put_ldev refcount imbalance during attach
drbd: new disk-option disable-write-same
drbd: Fix resource role for newly created resources in events2
drbd: mark symbols static where possible
drbd: Send P_NEG_ACK upon write error in protocol != C
drbd: add explicit plugging when submitting batches
drbd: change list_for_each_safe to while(list_first_entry_or_null)
drbd: introduce drbd_recv_header_maybe_unplug
...
Increase PPL area to 1MB and use it as circular buffer to store PPL. The
entry with highest generation number is the latest one. If PPL to be
written is larger then space left in a buffer, rewind the buffer to the
start (don't wrap it).
Signed-off-by: Pawel Baldysiak <pawel.baldysiak@intel.com>
Signed-off-by: Artur Paszkiewicz <artur.paszkiewicz@intel.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Since commit f15146380d ("fs: seq_file - add event counter to simplify
poll() support"), md.c code has been no longer used the private field of
the struct seq_file, but seq_release_private() has been continued to be
used to release the allocated seq_file. This seems to have been
forgotten. So convert it to use seq_release() instead of
seq_release_private().
Signed-off-by: Cihangir Akturk <cakturk@gmail.com>
Signed-off-by: Shaohua Li <shli@fb.com>
In case of external metadata arrays spare disks are added to containers
first. mdadm keeps monitoring /proc/mdstat output and when spare disk is
available, it moves it from the container to the array. The problem is
there is no notification of new spare disk in the container and mdadm
waits a long time (until timeout) before it takes the action.
Signed-off-by: Alexey Obitotskiy <aleksey.obitotskiy@intel.com>
Signed-off-by: Shaohua Li <shli@fb.com>
This way we don't need a block_device structure to submit I/O. The
block_device has different life time rules from the gendisk and
request_queue and is usually only available when the block device node
is open. Other callers need to explicitly create one (e.g. the lightnvm
passthrough code, or the new nvme multipathing code).
For the actual I/O path all that we need is the gendisk, which exists
once per block device. But given that the block layer also does
partition remapping we additionally need a partition index, which is
used for said remapping in generic_make_request.
Note that all the block drivers generally want request_queue or
sometimes the gendisk, so this removes a layer of indirection all
over the stack.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
->safemode should be triggered by mdadm for external metadaa array, otherwise
array's state confuses mdadm.
Fixes: 33182d15c6bf(md: always clear ->safemode when md_check_recovery gets the mddev lock.)
Cc: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
md_write_start() needs to clear the in_sync flag is it is set, or if
there might be a race with set_in_sync() such that the later will
set it very soon. In the later case it is sufficient to take the
spinlock to synchronize with set_in_sync(), and then set the flag
if needed.
The current test is incorrect.
It should be:
if "flag is set" or "race is possible"
"flag is set" is trivially "mddev->in_sync".
"race is possible" should be tested by "mddev->sync_checkers".
If sync_checkers is 0, then there can be no race. set_in_sync() will
wait in percpu_ref_switch_to_atomic_sync() for an RCU grace period,
and as md_write_start() holds the rcu_read_lock(), set_in_sync() will
be sure ot see the update to writes_pending.
If sync_checkers is > 0, there could be race. If md_write_start()
happened entirely between
if (!mddev->in_sync &&
percpu_ref_is_zero(&mddev->writes_pending)) {
and
mddev->in_sync = 1;
in set_in_sync(), then it would not see that is_sync had been set,
and set_in_sync() would not see that writes_pending had been
incremented.
This bug means that in_sync is sometimes not set when it should be.
Consequently there is a small chance that the array will be marked as
"clean" when in fact it is inconsistent.
Fixes: 4ad23a9764 ("MD: use per-cpu counter for writes_pending")
cc: stable@vger.kernel.org (v4.12+)
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
If ->safemode == 1, md_check_recovery() will try to get the mddev lock
and perform various other checks.
If mddev->in_sync is zero, it will call set_in_sync, and clear
->safemode. However if mddev->in_sync is not zero, ->safemode will not
be cleared.
When md_check_recovery() drops the mddev lock, the thread is woken
up again. Normally it would just check if there was anything else to
do, find nothing, and go to sleep. However as ->safemode was not
cleared, it will take the mddev lock again, then wake itself up
when unlocking.
This results in an infinite loop, repeatedly calling
md_check_recovery(), which RCU or the soft-lockup detector
will eventually complain about.
Prior to commit 4ad23a9764 ("MD: use per-cpu counter for
writes_pending"), safemode would only be set to one when the
writes_pending counter reached zero, and would be cleared again
when writes_pending is incremented. Since that patch, safemode
is set more freely, but is not reliably cleared.
So in md_check_recovery() clear ->safemode before checking ->in_sync.
Fixes: 4ad23a9764 ("MD: use per-cpu counter for writes_pending")
Cc: stable@vger.kernel.org (4.12+)
Reported-by: Dominik Brodowski <linux@dominikbrodowski.net>
Reported-by: David R <david@unsolicited.net>
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Pull MD update from Shaohua Li:
- fixed deadlock in MD suspend and a potential bug in bio allocation
(Neil Brown)
- fixed signal issue (Mikulas Patocka)
- fixed typo in FailFast test (Guoqing Jiang)
- other trival fixes
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/shli/md:
MD: fix sleep in atomic
MD: fix a null dereference
md: use a separate bio_set for synchronous IO.
md: change the initialization value for a spare device spot to MD_DISK_ROLE_SPARE
md/raid1: remove unused bio in sync_request_write
md/raid10: fix FailFast test for wrong device
md: don't use flush_signals in userspace processes
md: fix deadlock between mddev_suspend() and md_write_start()
bioset_free() will take a mutex, so can't get called with spinlock hold.
Fix: 5a85071c2cbc(md: use a separate bio_set for synchronous IO.)
Cc: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
rdev->mddev could be null in start time.
Reported-by: Ming Lei <ming.lei@redhat.com>
Fix: 5a85071c2cbc(md: use a separate bio_set for synchronous IO.)
Cc: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
md devices allocate a bio_set and use it for two
distinct purposes.
mddev->bio_set is used to clone bios as part of sending
upper level requests down to lower level devices,
and it is also use for synchronous IO such as superblock
and bitmap updates, and for correcting read errors.
This multiple usage can lead to deadlocks. It is likely
that cloned bios might be queued for write and to be
waiting for a metadata update before the write can be permitted.
If the cloning exhausted mddev->bio_set, the metadata update
may not be able to proceed.
This scenario has been seen during heavy testing, with lots of IO and
lots of memory pressure.
Address this by adding a new bio_set specifically for synchronous IO.
All synchronous IO goes directly to the underlying device and is not
queued at the md level, so request using entries from the new
mddev->sync_set will complete in a timely fashion.
Requests that use mddev->bio_set will sometimes need to wait
for synchronous IO, but will no longer risk deadlocking that iO.
Also: small simplification in mddev_put(): there is no need to
wait until the spinlock is released before calling bioset_free().
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
bio_clone() is no longer used.
Only bio_clone_bioset() or bio_clone_fast().
This is for the best, as bio_clone() used fs_bio_set,
and filesystems are unlikely to want to use bio_clone().
So remove bio_clone() and all references.
This includes a fix to some incorrect documentation.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
"flags" arguments are often seen as good API design as they allow
easy extensibility.
bioset_create_nobvec() is implemented internally as a variation in
flags passed to __bioset_create().
To support future extension, make the internal structure part of the
API.
i.e. add a 'flags' argument to bioset_create() and discard
bioset_create_nobvec().
Note that the bio_split allocations in drivers/md/raid* do not need
the bvec mempool - they should have used bioset_create_nobvec().
Suggested-by: Christoph Hellwig <hch@infradead.org>
Reviewed-by: Christoph Hellwig <hch@infradead.org>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
blk_queue_split() is always called with the last arg being q->bio_split,
where 'q' is the first arg.
Also blk_queue_split() sometimes uses the passed-in 'bs' and sometimes uses
q->bio_split.
This is inconsistent and unnecessary. Remove the last arg and always use
q->bio_split inside blk_queue_split()
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Credit-to: Javier González <jg@lightnvm.io> (Noticed that lightnvm was missed)
Reviewed-by: Javier González <javier@cnexlabs.com>
Tested-by: Javier González <javier@cnexlabs.com>
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The value for spare spot of sb->dev_roles is changed from
MD_DISK_ROLE_FAULTY to MD_DISK_ROLE_SPARE to keep align
with the value when the superblock is firstly created in
userspace.
Signed-off-by: Lidong Zhong <lzhong@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
If mddev_suspend() races with md_write_start() we can deadlock
with mddev_suspend() waiting for the request that is currently
in md_write_start() to complete the ->make_request() call,
and md_write_start() waiting for the metadata to be updated
to mark the array as 'dirty'.
As metadata updates done by md_check_recovery() only happen then
the mddev_lock() can be claimed, and as mddev_suspend() is often
called with the lock held, these threads wait indefinitely for each
other.
We fix this by having md_write_start() abort if mddev_suspend()
is happening, and ->make_request() aborts if md_write_start()
aborted.
md_make_request() can detect this abort, decrease the ->active_io
count, and wait for mddev_suspend().
Reported-by: Nix <nix@esperi.org.uk>
Fix: 68866e425be2(MD: no sync IO while suspended)
Cc: stable@vger.kernel.org
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJZPdbLAAoJEHm+PkMAQRiGx4wH/1nCjfnl6fE8oJ24/1gEAOUh
biFdqJkYZmlLYHVtYfLm4Ueg4adJdg0wx6qM/4RaAzmQVvLfDV34bc1qBf1+P95G
kVF+osWyXrZo5cTwkwapHW/KNu4VJwAx2D1wrlxKDVG5AOrULH1pYOYGOpApEkZU
4N+q5+M0ce0GJpqtUZX+UnI33ygjdDbBxXoFKsr24B7eA0ouGbAJ7dC88WcaETL+
2/7tT01SvDMo0jBSV0WIqlgXwZ5gp3yPGnklC3F4159Yze6VFrzHMKS/UpPF8o8E
W9EbuzwxsKyXUifX2GY348L1f+47glen/1sedbuKnFhP6E9aqUQQJXvEO7ueQl4=
=m2Gx
-----END PGP SIGNATURE-----
Merge tag 'v4.12-rc5' into for-4.13/block
We've already got a few conflicts and upcoming work depends on some of the
changes that have gone into mainline as regression fixes for this series.
Pull in 4.12-rc5 to resolve these conflicts and make it easier on down stream
trees to continue working on 4.13 changes.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Replace bi_error with a new bi_status to allow for a clear conversion.
Note that device mapper overloaded bi_error with a private value, which
we'll have to keep arround at least for now and thus propagate to a
proper blk_status_t value.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
The new per-cpu counter for writes_pending is initialised in
md_alloc(), which is not called by dm-raid.
So dm-raid fails when md_write_start() is called.
Move the initialization to the personality modules
that need it. This way it is always initialised when needed,
but isn't unnecessarily initialized (requiring memory allocation)
when the personality doesn't use writes_pending.
Reported-by: Heinz Mauelshagen <heinzm@redhat.com>
Fixes: 4ad23a9764 ("MD: use per-cpu counter for writes_pending")
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
The md private helper uuid_equal() collides with a generic helper
of the same name.
Rename the md private helper to md_uuid_equal() and do the same for
md_sb_equal().
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Shaohua Li <shli@kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Commit b685d3d65a "block: treat REQ_FUA and REQ_PREFLUSH as
synchronous" removed REQ_SYNC flag from WRITE_{FUA|PREFLUSH|...}
definitions. generic_make_request_checks() however strips REQ_FUA and
REQ_PREFLUSH flags from a bio when the storage doesn't report volatile
write cache and thus write effectively becomes asynchronous which can
lead to performance regressions
Fix the problem by making sure all bios which are synchronous are
properly marked with REQ_SYNC.
CC: linux-raid@vger.kernel.org
CC: Shaohua Li <shli@kernel.org>
Fixes: b685d3d65a
CC: stable@vger.kernel.org
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Shaohua Li <shli@fb.com>
This essentially reverts commit b5470dc5fc ("md: resolve external
metadata handling deadlock in md_allow_write") with some adjustments.
Since commit 6791875e2e ("md: make reconfig_mutex optional for writes
to md sysfs files.") changing array_state to 'active' does not use
mddev_lock() and will not cause a deadlock with md_allow_write(). This
revert simplifies userspace tools that write to sysfs attributes like
"stripe_cache_size" or "consistency_policy" because it removes the need
for special handling for external metadata arrays, checking for EAGAIN
and retrying the write.
Signed-off-by: Artur Paszkiewicz <artur.paszkiewicz@intel.com>
Signed-off-by: Shaohua Li <shli@fb.com>
1/ If an array has any read-only devices when it is started,
the array itself must be read-only
2/ A read-only device cannot be added to an array after it is
started.
3/ Setting an array to read-write should not succeed
if any member devices are read-only
Reported-and-Tested-by: Nanda Kishore Chinnaram <Nanda_Kishore_Chinna@dell.com>
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
md allows a new array device to be created by simply
opening a device file. This make it difficult to
remove the device and udev is likely to open the device file
as part of processing the REMOVE event.
There is an alternate mechanism for creating arrays
by writing to the new_array module parameter.
When using tools that work with this parameter, it is
best to disable the old semantics.
This new module parameter allows that.
Signed-off-by: NeilBrown <neilb@suse.com>
Acted-by: Coly Li <colyli@suse.de>
Signed-off-by: Shaohua Li <shli@fb.com>
The intention when creating the "new_array" parameter and the
possibility of having array names line "md_HOME" was to transition
away from the old way of creating arrays and to eventually only use
this new way.
The "old" way of creating array is to create a device node in /dev
and then open it. The act of opening creates the array.
This is problematic because sometimes the device node can be opened
when we don't want to create an array. This can easily happen
when some rule triggered by udev looks at a device as it is being
destroyed. The node in /dev continues to exist for a short period
after an array is stopped, and opening it during this time recreates
the array (as an inactive array).
Unfortunately no clear plan for the transition was created. It is now
time to fix that.
This patch allows devices with numeric names, like "md999" to be
created by writing to "new_array". This will only work if the minor
number given is not already in use. This will allow mdadm to
support the creation of arrays with numbers > 511 (currently not
possible) by writing to new_array.
mdadm can, at some point, use this approach to create *all* arrays,
which will allow the transition to only using the new-way.
Signed-off-by: NeilBrown <neilb@suse.com>
Acted-by: Coly Li <colyli@suse.de>
Signed-off-by: Shaohua Li <shli@fb.com>
md.c: it needs to release the mddev lock before
the array_size_store() returns.
Fixes: ab5a98b132 ("md-cluster: change array_sectors and update size are not supported")
Signed-off-by: Zhilong Liu <zlliu@suse.com>
Reviewed-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
if called md_set_readonly and set MD_CLOSING bit, the mddev cannot
be opened any more due to the MD_CLOING bit wasn't cleared. Thus it
needs to be cleared in md_ioctl after any call to md_set_readonly()
or do_md_stop().
Signed-off-by: NeilBrown <neilb@suse.com>
Fixes: af8d8e6f03 ("md: changes for MD_STILL_CLOSED flag")
Cc: stable@vger.kernel.org (v4.9+)
Signed-off-by: Zhilong Liu <zlliu@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
The 'writes_pending' counter is used to determine when the
array is stable so that it can be marked in the superblock
as "Clean". Consequently it needs to be updated frequently
but only checked for zero occasionally. Recent changes to
raid5 cause the count to be updated even more often - once
per 4K rather than once per bio. This provided
justification for making the updates more efficient.
So we replace the atomic counter a percpu-refcount.
This can be incremented and decremented cheaply most of the
time, and can be switched to "atomic" mode when more
precise counting is needed. As it is possible for multiple
threads to want a precise count, we introduce a
"sync_checker" counter to count the number of threads
in "set_in_sync()", and only switch the refcount back
to percpu mode when that is zero.
We need to be careful about races between set_in_sync()
setting ->in_sync to 1, and md_write_start() setting it
to zero. md_write_start() holds the rcu_read_lock()
while checking if the refcount is in percpu mode. If
it is, then we know a switch to 'atomic' will not happen until
after we call rcu_read_unlock(), in which case set_in_sync()
will see the elevated count, and not set in_sync to 1.
If it is not in percpu mode, we take the mddev->lock to
ensure proper synchronization.
It is no longer possible to quickly check if the count is zero, which
we previously did to update a timer or to schedule the md_thread.
So now we do these every time we decrement that counter, but make
sure they are fast.
mod_timer() already optimizes the case where the timeout value doesn't
actually change. We leverage that further by always rounding off the
jiffies to the timeout value. This may delay the marking of 'clean'
slightly, but ensure we only perform atomic operation here when absolutely
needed.
md_wakeup_thread() current always calls wake_up(), even if
THREAD_WAKEUP is already set. That too can be optimised to avoid
calls to wake_up().
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
If ->in_sync is being set just as md_write_start() is being called,
it is possible that set_in_sync() won't see the elevated
->writes_pending, and md_write_start() won't see the set ->in_sync.
To close this race, re-test ->writes_pending after setting ->in_sync,
and add memory barriers to ensure the increment of ->writes_pending
will be seen by the time of this second test, or the new ->in_sync
will be seen by md_write_start().
Add a spinlock to array_state_show() to ensure this temporary
instability is never visible from userspace.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Three separate places in md.c check if the number of active
writes is zero and, if so, sets mddev->in_sync.
There are a few differences, but there shouldn't be:
- it is always appropriate to notify the change in
sysfs_state, and there is no need to do this outside a
spin-locked region.
- we never need to check ->recovery_cp. The state of resync
is not relevant for whether there are any pending writes
or not (which is what ->in_sync reports).
So create set_in_sync() which does the correct tests and
makes the correct changes, and call this in all three
places.
Any behaviour changes here a minor and cosmetic.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
We use md_write_start() to increase the count of pending writes, and
md_write_end() to decrement the count. We currently count bios
submitted to md/raid5. Change it count stripe_heads that a WRITE bio
has been attached to.
So now, raid5_make_request() calls md_write_start() and then
md_write_end() to keep the count elevated during the setup of the
request.
add_stripe_bio() calls md_write_start() for each stripe_head, and the
completion routines always call md_write_end(), instead of only
calling it when raid5_dec_bi_active_stripes() returns 0.
make_discard_request also calls md_write_start/end().
The parallel between md_write_{start,end} and use of bi_phys_segments
can be seen in that:
Whenever we set bi_phys_segments to 1, we now call md_write_start.
Whenever we increment it on non-read requests with
raid5_inc_bi_active_stripes(), we now call md_write_start().
Whenever we decrement bi_phys_segments on non-read requsts with
raid5_dec_bi_active_stripes(), we now call md_write_end().
This reduces our dependence on keeping a per-bio count of active
stripes in bi_phys_segments.
md_write_inc() is added which parallels md_write_start(), but requires
that a write has already been started, and is certain never to sleep.
This can be used inside a spinlocked region when adding to a write
request.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Since we have switched to sync way to handle METADATA_UPDATED
msg for md-cluster, then process_metadata_update is depended
on mddev->thread->wqueue.
With the new change, clustered raid could possible hang if
array received a METADATA_UPDATED msg after array unregistered
mddev->thread, so we need to stop clustered raid (bitmap_destroy
-> bitmap_free -> md_cluster_stop) earlier than unregister
thread (mddev_detach -> md_unregister_thread).
And this change should be safe for non-clustered raid since
all writes are stopped before the destroy. Also in md_run,
we activate the personality (pers->run()) before activating
the bitmap (bitmap_create()). So it is pleasingly symmetric
to stop the bitmap (bitmap_destroy()) before stopping the
personality (__md_stop() calls pers->free()), we achieve this
by move bitmap_destroy to the beginning of __md_stop.
But we don't want to break the codes for waiting behind IO as
Shaohua mentioned, so introduce bitmap_wait_behind_writes to
call the codes, and call the new fun in both mddev_detach and
bitmap_destroy, then we will not break original behind IO code
and also fit the new condition well.
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Allow writing to 'consistency_policy' attribute when the array is
active. Add a new function 'change_consistency_policy' to the
md_personality operations structure to handle the change in the
personality code. Values "ppl" and "resync" are accepted and
turn PPL on and off respectively.
When enabling PPL its location and size should first be set using
'ppl_sector' and 'ppl_size' attributes and a valid PPL header should be
written at this location on each member device.
Enabling or disabling PPL is performed under a suspended array. The
raid5_reset_stripe_cache function frees the stripe cache and allocates
it again in order to allocate or free the ppl_pages for the stripes in
the stripe cache.
Signed-off-by: Artur Paszkiewicz <artur.paszkiewicz@intel.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Add 'consistency_policy' attribute for array. It indicates how the array
maintains consistency in case of unexpected shutdown.
Add 'ppl_sector' and 'ppl_size' for rdev, which describe the location
and size of the PPL space on the device. They can't be changed for
active members if the array is started and PPL is enabled, so in the
setter functions only basic checks are performed. More checks are done
in ppl_validate_rdev() when starting the log.
These attributes are writable to allow enabling PPL for external
metadata arrays and (later) to enable/disable PPL for a running array.
Signed-off-by: Artur Paszkiewicz <artur.paszkiewicz@intel.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Include information about PPL location and size into mdp_superblock_1
and copy it to/from rdev. Because PPL is mutually exclusive with bitmap,
put it in place of 'bitmap_offset'. Add a new flag MD_FEATURE_PPL for
'feature_map', analogically to MD_FEATURE_BITMAP_OFFSET. Add MD_HAS_PPL
to mddev->flags to indicate that PPL is enabled on an array.
Signed-off-by: Artur Paszkiewicz <artur.paszkiewicz@intel.com>
Signed-off-by: Shaohua Li <shli@fb.com>
To update size for cluster raid, we need to make
sure all nodes can perform the change successfully.
However, it is possible that some of them can't do
it due to failure (bitmap_resize could fail). So
we need to consider the issue before we set the
capacity unconditionally, and we use below steps
to perform sanity check.
1. A change the size, then broadcast METADATA_UPDATED
msg.
2. B and C receive METADATA_UPDATED change the size
excepts call set_capacity, sync_size is not update
if the change failed. Also call bitmap_update_sb
to sync sb to disk.
3. A checks other node's sync_size, if sync_size has
been updated in all nodes, then send CHANGE_CAPACITY
msg otherwise send msg to revert previous change.
4. B and C call set_capacity if receive CHANGE_CAPACITY
msg, otherwise pers->resize will be called to restore
the old value.
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Previously, when node received METADATA_UPDATED msg, it just
need to wakeup mddev->thread, then md_reload_sb will be called
eventually.
We taken the asynchronous way to avoid a deadlock issue, the
deadlock issue could happen when one node is receiving the
METADATA_UPDATED msg (wants reconfig_mutex) and trying to run
the path:
md_check_recovery -> mddev_trylock(hold reconfig_mutex)
-> md_update_sb-metadata_update_start
(want EX on token however token is
got by the sending node)
Since we will support resizing for clustered raid, and we
need the metadata update handling to be synchronous so that
the initiating node can detect failure, so we need to change
the way for handling METADATA_UPDATED msg.
But, we obviously need to avoid above deadlock with the
sync way. To make this happen, we considered to not hold
reconfig_mutex to call md_reload_sb, if some other thread
has already taken reconfig_mutex and waiting for the 'token',
then process_recvd_msg() can safely call md_reload_sb()
without taking the mutex. This is because we can be certain
that no other thread will take the mutex, and we also certain
that the actions performed by md_reload_sb() won't interfere
with anything that the other thread is in the middle of.
To make this more concrete, we added a new cinfo->state bit
MD_CLUSTER_HOLDING_MUTEX_FOR_RECVD
Which is set in lock_token() just before dlm_lock_sync() is
called, and cleared just after. As lock_token() is always
called with reconfig_mutex() held (the specific case is the
resync_info_update which is distinguished well in previous
patch), if process_recvd_msg() finds that the new bit is set,
then the mutex must be held by some other thread, and it will
keep waiting.
So process_metadata_update() can call md_reload_sb() if either
mddev_trylock() succeeds, or if MD_CLUSTER_HOLDING_MUTEX_FOR_RECVD
is set. The tricky bit is what to do if neither of these apply.
We need to wait. Fortunately mddev_unlock() always calls wake_up()
on mddev->thread->wqueue. So we can get lock_token() to call
wake_up() on that when it sets the bit.
There are also some related changes inside this commit:
1. remove RELOAD_SB related codes since there are not valid anymore.
2. mddev is added into md_cluster_info then we can get mddev inside
lock_token.
3. add new parameter for lock_token to distinguish reconfig_mutex
is held or not.
And, we need to set MD_CLUSTER_HOLDING_MUTEX_FOR_RECVD in below:
1. set it before unregister thread, otherwise a deadlock could
appear if stop a resyncing array.
This is because md_unregister_thread(&cinfo->recv_thread) is
blocked by recv_daemon -> process_recvd_msg
-> process_metadata_update.
To resolve the issue, MD_CLUSTER_HOLDING_MUTEX_FOR_RECVD is
also need to be set before unregister thread.
2. set it in metadata_update_start to fix another deadlock.
a. Node A sends METADATA_UPDATED msg (held Token lock).
b. Node B wants to do resync, and is blocked since it can't
get Token lock, but MD_CLUSTER_HOLDING_MUTEX_FOR_RECVD is
not set since the callchain
(md_do_sync -> sync_request
-> resync_info_update
-> sendmsg
-> lock_comm -> lock_token)
doesn't hold reconfig_mutex.
c. Node B trys to update sb (held reconfig_mutex), but stopped
at wait_event() in metadata_update_start since we have set
MD_CLUSTER_SEND_LOCK flag in lock_comm (step 2).
d. Then Node B receives METADATA_UPDATED msg from A, of course
recv_daemon is blocked forever.
Since metadata_update_start always calls lock_token with reconfig_mutex,
we need to set MD_CLUSTER_HOLDING_MUTEX_FOR_RECVD here as well, and
lock_token don't need to set it twice unless lock_token is invoked from
lock_comm.
Finally, thanks to Neil for his great idea and help!
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
The sb->super_offset should be big-endian, but the rdev->sb_start is in
host byte order, so fix this by adding cpu_to_le64.
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Shaohua Li <shli@fb.com>
These arrays, created with "mdadm --build" don't benefit from a limit.
The default will be used, which is '0' and is interpreted as "don't
impose a limit".
Reported-by: ian_bruce@mail.ru
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
raid1_resize and raid5_resize should also check the
mddev->queue if run underneath dm-raid.
And both set_capacity and revalidate_disk are used in
pers->resize such as raid1, raid10 and raid5. So
move them from personality file to common code.
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
We are going to split <linux/sched/signal.h> out of <linux/sched.h>, which
will have to be picked up from other headers and a couple of .c files.
Create a trivial placeholder <linux/sched/signal.h> file that just
maps to <linux/sched.h> to make this patch obviously correct and
bisectable.
Include the new header in the files that are going to need it.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull md updates from Shaohua Li:
"Mainly fixes bugs and improves performance:
- Improve scalability for raid1 from Coly
- Improve raid5-cache read performance, disk efficiency and IO
pattern from Song and me
- Fix a race condition of disk hotplug for linear from Coly
- A few cleanup patches from Ming and Byungchul
- Fix a memory leak from Neil
- Fix WRITE SAME IO failure from me
- Add doc for raid5-cache from me"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/shli/md: (23 commits)
md/raid1: fix write behind issues introduced by bio_clone_bioset_partial
md/raid1: handle flush request correctly
md/linear: shutup lockdep warnning
md/raid1: fix a use-after-free bug
RAID1: avoid unnecessary spin locks in I/O barrier code
RAID1: a new I/O barrier implementation to remove resync window
md/raid5: Don't reinvent the wheel but use existing llist API
md: fast clone bio in bio_clone_mddev()
md: remove unnecessary check on mddev
md/raid1: use bio_clone_bioset_partial() in case of write behind
md: fail if mddev->bio_set can't be created
block: introduce bio_clone_bioset_partial()
md: disable WRITE SAME if it fails in underlayer disks
md/raid5-cache: exclude reclaiming stripes in reclaim check
md/raid5-cache: stripe reclaim only counts valid stripes
MD: add doc for raid5-cache
Documentation: move MD related doc into a separate dir
md: ensure md devices are freed before module is unloaded.
md/r5cache: improve journal device efficiency
md/r5cache: enable chunk_aligned_read with write back cache
...
Firstly bio_clone_mddev() is used in raid normal I/O and isn't
in resync I/O path.
Secondly all the direct access to bvec table in raid happens on
resync I/O except for write behind of raid1, in which we still
use bio_clone() for allocating new bvec table.
So this patch replaces bio_clone() with bio_clone_fast()
in bio_clone_mddev().
Also kill bio_clone_mddev() and call bio_clone_fast() directly, as
suggested by Christoph Hellwig.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Shaohua Li <shli@fb.com>
mddev is never NULL and neither is ->bio_set, so
remove the check.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Shaohua Li <shli@fb.com>
The current behaviour is to fall back to allocate
bio from 'fs_bio_set', that isn't a correct way
because it might cause deadlock.
So this patch simply return failure if mddev->bio_set
can't be created.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Commit: cbd1998377 ("md: Fix unfortunate interaction with evms")
change mddev_put() so that it would not destroy an md device while
->ctime was non-zero.
Unfortunately, we didn't make sure to clear ->ctime when unloading
the module, so it is possible for an md device to remain after
module unload. An attempt to open such a device will trigger
an invalid memory reference in:
get_gendisk -> kobj_lookup -> exact_lock -> get_disk
when tring to access disk->fops, which was in the module that has
been removed.
So ensure we clear ->ctime in md_exit(), and explain how that is useful,
as it isn't immediately obvious when looking at the code.
Fixes: cbd1998377 ("md: Fix unfortunate interaction with evms")
Tested-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
We will want to have struct backing_dev_info allocated separately from
struct request_queue. As the first step add pointer to backing_dev_info
to request_queue and convert all users touching it. No functional
changes in this patch.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <axboe@fb.com>
For safer operation, all arrays start in write-through mode, which has been
better tested and is more mature. And actually the write-through/write-mode
isn't persistent after array restarted, so we always start array in
write-through mode. However, if recovery found data-only stripes before the
shutdown (from previous write-back mode), it is not safe to start the array in
write-through mode, as write-through mode can not handle stripes with data in
write-back cache. To solve this problem, we flush all data-only stripes in
r5l_recovery_log(). When r5l_recovery_log() returns, the array starts with
empty cache in write-through mode.
This logic is implemented in r5c_recovery_flush_data_only_stripes():
1. enable write back cache
2. flush all stripes
3. wake up conf->mddev->thread
4. wait for all stripes get flushed (reuse wait_for_quiescent)
5. disable write back cache
The wait in 4 will be waked up in release_inactive_stripe_list()
when conf->active_stripes reaches 0.
It is safe to wake up mddev->thread here because all the resource
required for the thread has been initialized.
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Pull block layer updates from Jens Axboe:
"This is the main block pull request this series. Contrary to previous
release, I've kept the core and driver changes in the same branch. We
always ended up having dependencies between the two for obvious
reasons, so makes more sense to keep them together. That said, I'll
probably try and keep more topical branches going forward, especially
for cycles that end up being as busy as this one.
The major parts of this pull request is:
- Improved support for O_DIRECT on block devices, with a small
private implementation instead of using the pig that is
fs/direct-io.c. From Christoph.
- Request completion tracking in a scalable fashion. This is utilized
by two components in this pull, the new hybrid polling and the
writeback queue throttling code.
- Improved support for polling with O_DIRECT, adding a hybrid mode
that combines pure polling with an initial sleep. From me.
- Support for automatic throttling of writeback queues on the block
side. This uses feedback from the device completion latencies to
scale the queue on the block side up or down. From me.
- Support from SMR drives in the block layer and for SD. From Hannes
and Shaun.
- Multi-connection support for nbd. From Josef.
- Cleanup of request and bio flags, so we have a clear split between
which are bio (or rq) private, and which ones are shared. From
Christoph.
- A set of patches from Bart, that improve how we handle queue
stopping and starting in blk-mq.
- Support for WRITE_ZEROES from Chaitanya.
- Lightnvm updates from Javier/Matias.
- Supoort for FC for the nvme-over-fabrics code. From James Smart.
- A bunch of fixes from a whole slew of people, too many to name
here"
* 'for-4.10/block' of git://git.kernel.dk/linux-block: (182 commits)
blk-stat: fix a few cases of missing batch flushing
blk-flush: run the queue when inserting blk-mq flush
elevator: make the rqhash helpers exported
blk-mq: abstract out blk_mq_dispatch_rq_list() helper
blk-mq: add blk_mq_start_stopped_hw_queue()
block: improve handling of the magic discard payload
blk-wbt: don't throttle discard or write zeroes
nbd: use dev_err_ratelimited in io path
nbd: reset the setup task for NBD_CLEAR_SOCK
nvme-fabrics: Add FC LLDD loopback driver to test FC-NVME
nvme-fabrics: Add target support for FC transport
nvme-fabrics: Add host support for FC transport
nvme-fabrics: Add FC transport LLDD api definitions
nvme-fabrics: Add FC transport FC-NVME definitions
nvme-fabrics: Add FC transport error codes to nvme.h
Add type 0x28 NVME type code to scsi fc headers
nvme-fabrics: patch target code in prep for FC transport support
nvme-fabrics: set sqe.command_id in core not transports
parser: add u64 number parser
nvme-rdma: align to generic ib_event logging helper
...
The mddev->flags are used for different purposes. There are a lot of
places we check/change the flags without masking unrelated flags, we
could check/change unrelated flags. These usage are most for superblock
write, so spearate superblock related flags. This should make the code
clearer and also fix real bugs.
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
md_open() gets a counted reference on an mddev using mddev_find().
If it ends up returning an error, it must drop this reference.
There are two error paths where the reference is not dropped.
One only happens if the process is signalled and an awkward time,
which is quite unlikely.
The other was introduced recently in commit af8d8e6f0.
Change the code to ensure the drop the reference when returning an error,
and make it harded to re-introduce this sort of bug in the future.
Reported-by: Marc Smith <marc.smith@mcc.edu>
Fixes: af8d8e6f03 ("md: changes for MD_STILL_CLOSED flag")
Signed-off-by: NeilBrown <neilb@suse.com>
Acked-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
__md_stop_writes currently doesn't stop raid5-cache reclaim thread. It's
possible the reclaim thread is still running and doing write, which
doesn't match what __md_stop_writes should do. The extra ->quiesce()
call should not harm any raid types. For raid5-cache, this will
guarantee we reclaim all caches before we update superblock.
Signed-off-by: Shaohua Li <shli@fb.com>
Reviewed-by: NeilBrown <neilb@suse.de>
Cc: Song Liu <songliubraving@fb.com>
There is mechanism to suspend a kernel thread. Use it instead of playing
create/destroy game.
Signed-off-by: Shaohua Li <shli@fb.com>
Reviewed-by: NeilBrown <neilb@suse.de>
Cc: Song Liu <songliubraving@fb.com>