This patch adds the Device Tree bindings for the Broadcom GENET Gigabit
Ethernet controller. A bunch of examples are provided to illustrate the
versatile aspect of the hardare.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new configuration symbol: CONFIG_BCMGENET which allows
us to build the Broadcom GENET driver and hook the driver files into the
build system.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for configuring the port multiplexer hardware
which resides in front of the GENET Ethernet MAC controller. This allows
us to support:
- internal PHYs (using drivers/net/phy/bcm7xxx.c)
- MoCA PHYs which are an entirely separate hardware block not covered
here
- external PHYs and switches
Note that MoCA and switches are currently supported using the emulated
"fixed PHY" driver.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the BCMGENET main driver file which supports the
following:
- GENET hardware from V1 to V4
- support for reading the UniMAC MIB counters statistics
- support for the 5 transmit queues
- support for RX/TX checksum offload and SG
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patchs adds the bcmgenet.h header file which contains all the
hardware definitions for the GENETv1 to v4 hardware blocks as well as
the driver private structure and MIB counters.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the Broadcom BCM7xxx Set Top Box SoCs
internal PHYs. This driver supports the following generation of SoCs:
- BCM7366, BCM7439, BCM7445 (28nm process)
- all 40nm and 65nm (older MIPS-based SoCs)
The PHYs on these SoCs require a bunch of workarounds to operate
correctly, both during configuration time and at suspend/resume time,
the driver handles that for us.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Broadcom BCM54xx register definitions are shared between BCM54xx and
BCM7xx internal PHYs for which we are adding support. Extract these
register definitions and put them in include/linux/brcmphy.h for use by
the BCM7xxx internal PHY driver.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MoCA PHYs are using coaxial (BNC-like) connectors, update the
transceiver port type when replying to ethtool.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some Ethernet MACs are connected to a MoCA PHY which will handle the
low-level job of sending Ethernet frames on the coaxial cable, these
Ethernet MACs need to know about it to be properly configured.
Add a new PHY mode "moca" and update the Device Tree parsing logic to
look for it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace some magic numbers which describe states of GE model
loss generator with enumerate.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In netem_change(), we have already get "struct netem_sched_data *q".
Replace params of get_correlation() and other similar functions with
"struct netem_sched_data *q".
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
get_dist_table() and get_loss_clg() may be failed. These
two functions should be called after setting the members
of qdisc_priv(sch), or it will break the old settings while
either of them is failed.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Packets which have L2 address different from ours should be
already filtered before entering into ip_forward().
Perform that check at the beginning to avoid processing such packets.
Signed-off-by: Denis Kirjanov <kda@linux-powerpc.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
One of my pet coding style peeves is the practice of
adding extra return; at the end of function.
Kill several instances of this in network code.
I suppose some coccinelle wizardy could do this automatically.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 684bad1107 "tcp: use PRR to reduce cwin in CWR state" removed all
calls to min_cwnd, so we can safely remove it.
Also, remove tcp_reno_min_cwnd because it was only used for min_cwnd.
Signed-off-by: Stanislav Fomichev <stfomichev@yandex-team.ru>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently multi-channel configuration is read via the QUERY_FW_CONFIG cmd.
This method has been deprecated by the Skyhawk-R FW. Instead,
GET_PROFILE_CONFIG::port-desc must be used to query this configuration.
This patch also:
a) introduces a few macros to identify certain categories of multi-channel
configs
2) re-factors the be_cmd_set_profile_config() code to be able to read any kind
of desc (and not just the nic-desc.)
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch logs a kernel message when a HW error(SLIPORT_ERROR in Lancer and UE
in BEx/Skyhawk) is detected. The log message for BE3 was missing earlier.
This patch also refactors the code by segregating error-detection and reporting
code for Lancer and BEx/SH.
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlL7RxcACgkQjTAFq1RaXHNcKACgk4Vj+1KlmWVEin8VPoJBX86m
RasAn36pSY1OszxypJOF0O1s0qO9ld5K
=383M
-----END PGP SIGNATURE-----
Merge tag 'linux-can-next-for-3.15-20140212' of git://gitorious.org/linux-can/linux-can-next
linux-can-next-for-3.15-20140212
Marc Kleine-Budde says:
====================
this is a pull request of eight patches for net-next/master.
Florian Vaussard contributed a series that merged the sja1000 of_platform
into the platform driver. The of_platform driver is finally removed.
Stephane Grosjean supplied a patch to allocate CANFD skbs. In a patch
by Uwe Kleine-König another missing copyright information was added to
a userspace header. And a patch by Yoann DI RUZZA that adds listen only
mode to the at91_can driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver #define's and uses ETHERSMALL macro for the minimum Ethernet frame
size for which we have a standard macro ETH_ZLEN. Use the latter instead of
the home-grown one.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jon Maloy says:
====================
tipc: clean up media and bearer layer
This commit series aims at facilitating future changes to the
locking policy around nodes, links and bearers.
Currently, we have a big read/write lock (net_lock) that is used for
serializing all changes to the node, link and bearer lists, as well
as to their mutual pointers and references.
But, in order to allow for concurrent access to the contents of these
structures, net_lock is only used in read mode by the data path code,
and hence a finer granular locking policy must be applied inside the
scope of net_lock: a spinlock (node_lock) for each node structure,
and another one (bearer_lock) for protection of bearer structures.
This locking policy has proved hard to maintain. We have several
times encountered contention problems between node_lock and
bearer_lock, and with the advent of the RCU locking mechanism we
feel it is anyway obsolete and ripe for improvements.
We now plan to replace net_lock with an RCU lock, as well as
getting rid of bearer_lock altogether. This will both reduce data
path overhead and make the code more manageable, while reducing the
risk of future lock contention problems.
Prior to these changes, we need to do some necessary cleanup and
code consolidation. This is what we do with this commit series,
before we finally remove bearer_lock. In a later series we will
replace net_lock with an RCU lock.
v2:
- Re-inserted a removed kerneldoc entry in commit#5, based on
feedback from D. Miller.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In an earlier commit, ("tipc: remove links list from bearer struct")
we described three issues that need to be pre-emptively resolved before
we can remove tipc_net_lock. Here we resolve issue a) described in that
commit:
"a) In access method #2, we access the link before taking the
protecting node_lock. This will not work once net_lock is gone,
so we will have to change the access order. We will deal with
this in a later commit in this series."
Here, we change that access order, by ensuring that the function
link_find_link() returns only a safe reference for finding
the link, i.e., a node pointer and an index into its 'links' array,
not the link pointer itself. We also change all callers of this
function to first take the node lock before they can check if there
still is a valid link pointer at the returned index. Since the
function now returns a node pointer rather than a link pointer,
we rename it to the more appropriate 'tipc_link_find_owner().
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the earlier commits ("tipc: remove 'links' list from
tipc_bearer struct") and ("tipc: introduce new spinlock to protect
struct link_req"), there is no longer any need to protect struct
link_req or or any link list by use of bearer_lock. Furthermore,
we have eliminated the need for using bearer_lock during downcalls
(send) from the link to the bearer, since we have ensured that
bearers always have a longer life cycle that their associated links,
and always contain valid data.
So, the only need now for a lock protecting bearers is for guaranteeing
consistency of the bearer list itself. For this, it is sufficient, at
least for the time being, to continue applying 'net_lock´ in write mode.
By removing bearer_lock we also pre-empt introduction of issue b) descibed
in the previous commit "tipc: remove 'links' list from tipc_bearer struct":
"b) When the outer protection from net_lock is gone, taking
bearer_lock and node_lock in opposite order of method 1) and 2)
will become an obvious deadlock hazard".
Therefore, we now eliminate the bearer_lock spinlock.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a bearer is disabled, all its attached links are deleted.
Ideally, we should do link failover to redundant links on other bearers,
if there are any, in such cases. This would be consistent with current
behavior when a link is reset, but not deleted. However, due to the
complexity involved, and the (wrongly) perceived low demand for this
feature, it was never implemented until now.
We mark the doomed link for deletion with a new flag, but wait until the
failover process is finished before we actually delete it. With the
improved link tunnelling/failover code introduced earlier in this commit
series, it is now easy to identify a spot in the code where the failover
is finished and it is safe to delete the marked link. Moreover, the test
for the flag and the deletion can be done synchronously, and outside the
most time critical data path.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We change the order of checking for destination users when processing
incoming packets. By placing the checks for users that may potentially
replace the processed buffer, i.e., CHANGEOVER_PROTOCOL and
MSG_FRAGMENTER, in a separate step before we check for the true end
users, we get rid of a label and a 'goto', at the same time making the
code more comprehensible and easy to follow.
This commit does not change any functionality, it is just a cosmetic
code reshuffle.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the previous redesign of the tunnel reception algorithm and
functions, we finalize it by renaming a couple of stack variables
in tipc_tunnel_rcv(). This makes it more consistent with the naming
scheme elsewhere in this part of the code.
This change is purely cosmetic, with no functional changes.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We simplify and slim down the code in function tipc_tunnel_rcv()
No impact on the users of this function.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the earlier commits in this series related to the function
tipc_link_tunnel_rcv(), we can now go further and simplify its
signature.
The function now consumes all DUPLICATE packets, and only returns such
ORIGINAL packets that are ready for immediate delivery, i.e., no
more link level protocol processing needs to be done by the caller.
As a consequence, the the caller, tipc_rcv(), does not access the link
pointer after call return, and it becomes unnecessary to pass a link
pointer reference in the call. Instead, we now only pass it the tunnel
link's owner node, which is sufficient to find the destination link for
the tunnelled packet.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a link is reset, and there is a redundant link available, all
sender sockets will steer their subsequent traffic through the
remaining link. In order to guarantee preserved packet order and
cardinality during the transition, we tunnel the failing link's send
queue through the remaining link before we allow any sockets to use it.
In this commit, we change the algorithm for receiving failover
("ORIGINAL_MSG") packets in tipc_link_tunnel_rcv(), at the same time
delegating it to a new subfuncton, tipc_link_failover_rcv(). Instead
of directly returning an extracted inner packet to the packet reception
loop in tipc_rcv(), we first check if it is a message fragment, in which
case we append it to the reset link's fragment chain. If the fragment
chain is complete, we return the whole chain instead of the individual
buffer, eliminating any need for the tipc_rcv() loop to do reassembly of
tunneled packets.
This change makes it possible to further simplify tipc_link_tunnel_rcv(),
as well as the calling tipc_rcv() loop. We will do that in later
commits. It also makes it possible to identify a single spot in the code
where we can tell that a failover procedure is finished, something that
is useful when we are deleting links after a failover. This will also
be done in a later commit.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a second link to a destination comes up, some sender sockets will
steer their subsequent traffic through the new link. In order to
guarantee preserved packet order and cardinality for those sockets, we
tunnel a duplicate of the old link's send queue through the new link
before we open it for regular traffic. The last arriving packet copy,
on whichever link, will be dropped at the receiving end based on the
original sequence number, to ensure that only one copy is delivered to
the end receiver.
In this commit, we change the algorithm for receiving DUPLICATE_MSG
packets, at the same time delegating it to a new subfunction,
tipc_link_dup_rcv(). Instead of returning an extracted inner packet to
the packet reception loop in tipc_rcv(), we just add it to the receiving
(new) link's deferred packet queue. The packet will then be processed by
that link when it receives its first non-tunneled packet, i.e., at
latest when the changeover procedure is finished.
Because tipc_link_tunnel_rcv()/tipc_link_dup_rcv() now is consuming all
packets of type DUPLICATE_MSG, the calling tipc_rcv() function can omit
testing for this. This in turn means that the current conditional jump
to the label 'protocol_check' becomes redundant, and we can remove that
label.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In our ongoing effort to simplify the TIPC locking structure,
we see a need to remove the linked list for tipc_links
in the bearer. This can be explained as follows.
Currently, we have three different ways to access a link,
via three different lists/tables:
1: Via a node hash table:
Used by the time-critical outgoing/incoming data paths.
(e.g. link_send_sections_fast() and tipc_recv_msg() ):
grab net_lock(read)
find node from node hash table
grab node_lock
select link
grab bearer_lock
send_msg()
release bearer_lock
release node lock
release net_lock
2: Via a global linked list for nodes:
Used by configuration commands (link_cmd_set_value())
grab net_lock(read)
find node and link from global node list (using link name)
grab node_lock
update link
release node lock
release net_lock
(Same locking order as above. No problem.)
3: Via the bearer's linked link list:
Used by notifications from interface (e.g. tipc_disable_bearer() )
grab net_lock(write)
grab bearer_lock
get link ptr from bearer's link list
get node from link
grab node_lock
delete link
release node lock
release bearer_lock
release net_lock
(Different order from above, but works because we grab the
outer net_lock in write mode first, excluding all other access.)
The first major goal in our simplification effort is to get rid
of the "big" net_lock, replacing it with rcu-locks when accessing
the node list and node hash array. This will come in a later patch
series.
But to get there we first need to rewrite access methods ##2 and 3,
since removal of net_lock would introduce three major problems:
a) In access method #2, we access the link before taking the
protecting node_lock. This will not work once net_lock is gone,
so we will have to change the access order. We will deal with
this in a later commit in this series, "tipc: add node lock
protection to link found by link_find_link()".
b) When the outer protection from net_lock is gone, taking
bearer_lock and node_lock in opposite order of method 1) and 2)
will become an obvious deadlock hazard. This is fixed in the
commit ("tipc: remove bearer_lock from tipc_bearer struct")
later in this series.
c) Similar to what is described in problem a), access method #3
starts with using a link pointer that is unprotected by node_lock,
in order to via that pointer find the correct node struct and
lock it. Before we remove net_lock, this access order must be
altered. This is what we do with this commit.
We can avoid introducing problem problem c) by even here using the
global node list to find the node, before accessing its links. When
we loop though the node list we use the own bearer identity as search
criteria, thus easily finding the links that are associated to the
resetting/disabling bearer. It should be noted that although this
method is somewhat slower than the current list traversal, it is in
no way time critical. This is only about resetting or deleting links,
something that must be considered relatively infrequent events.
As a bonus, we can get rid of the mutual pointers between links and
bearers. After this commit, pointer dependency go in one direction
only: from the link to the bearer.
This commit pre-empts introduction of problem c) as described above.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the 'started' field in struct tipc_link represents only a
binary state, 'started' or 'not started'. We need it to represent
more link execution states in the coming commits in this series.
Hence, we rename the field to 'flags', and define the current
started/non-started state to be represented by the LSB bit of
that field.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We break out the code for deleting attached links in the
function bearer_disable(), and define a new function named
tipc_link_delete_list() to do this job.
This commit incurs no functional changes, but makes the code of
function bearer_disable() cleaner. It is also a preparation
for a more important change to the bearer code, in a subsequent
commit in this series.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We break out the code for resetting attached links in the
function tipc_reset_bearer(), and define a new function named
tipc_link_reset_list() to do this job.
This commit incurs no functional changes, but makes the code
of function tipc_reset_bearer() cleaner. It is also a preparation
for a more important change to the bearer code, in a subsequent
commit in this series.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function tipc_link_recv_fragment(struct sk_buff **buf) currently
leaves the value of the input buffer pointer undefined when it returns,
except when the return code indicates that the reassembly is complete.
This despite the fact that it always consumes the input buffer.
Here, we enforce a stricter behavior by this function, ensuring that
the returned buffer pointer is non-NULL if and only if the reassembly
is complete. This makes it possible to test for the buffer pointer as
criteria for successful reassembly.
We also rename the function to tipc_link_frag_rcv(), which is both
shorter and more in line with common naming practice in the network
subsystem.
Apart from the new name, these changes have no impact on current
users of the function, but makes it more practical for use in some
planned future commits.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The inline functions in addr.h uses tipc_own_addr which is exported by
core.h, but addr.h never actually includes it. It works because it is
explicitly included where this is used, but it looks a bit strange.
Include core.h in addr.h explicitly to make the dependency clearer.
Signed-off-by: Andreas Bofjäll <andreas.bofjall@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dev_valid_name() will check the buffer length for input name, no need to
check it twice.
Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Veaceslav Falico <vfalico@redhat.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Reviewed-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dev_set_mac_address() will check the dev->netdev_ops->ndo_set_mac_address,
so no need to check it in bond_set_mac_address().
Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Veaceslav Falico <vfalico@redhat.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Reviewed-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are trying to mirror the local traffic from lo to eth0,
allowing setting mac address of lo to eth0 would make
the ether addresses in these packets correct, so that
we don't have to modify the ether header again.
Since usually no one cares about its mac address (all-zero),
it is safe to allow those who care to set its mac address.
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: Eric Dumazet <edumazet@google.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Aaron Brown says:
====================
Intel Wired LAN Driver Updates
This series contains updates to i40e and i40evf, primarily reset
handling / refactoring along with a fair amount of minor cleanup.
Jesse fixes some spelling, bumps the version and other trivial fixes.
Akeem sets a bit that is needed before shutdown in the case of
tx_timeout recovery failure. Mitch refactors reset handling along
with a whole bunch of clean up.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Respond better to a VF reset event. When a reset is signaled by the
PF, or detected by the watchdog task, prevent the watchdog from
processing admin queue requests, and schedule the reset task.
In the reset task, wait first for the reset to start, then for it to
complete, then reinit the driver.
If the reset never appears to complete after a long, long time (>10
seconds is possible depending on what's going on with the PF driver),
then set a flag to indicate that PF communications have failed.
If this flag is set, check for the reset to complete in the watchdog,
and attempt to do a full reinitialization of the driver from scratch.
With these changes the VF driver correctly handles a PF reset event
while running on bare metal, or in a VM.
Also update copyrights.
Change-ID: I93513efd0b50523a8345e7f6a33a5e4f8a2a5996
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As pointed out by Dan Carpenter (from Oracle), the flags variable is
declared as a 64-bit long but all of the flags are defined as u32,
which may lead to unintended consequences. Fix this by declaring flags
as u32 (since we don't need any more than about a dozen flags right
now), and remove the volatile qualifier, since it's unnecessary and
just makes checkpatch cry.
Change-ID: I137d3bb1842bf7e9456b5929ca54e3b0ed45dcab
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Dan Carpenter <dan.carpenter@oracle.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we store the traffic vector names in the queue vector struct, we
don't need to maintain an array of strings for these names in the
adapter structure. Replace this array with a single string and use it
when allocating the misc irq vector.
Also update copyrights.
Change-ID: I664f096c3c008210d6a04a487163e8aa934fee5b
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Locate the structure in the correct header file.
Change-ID: Ic7853131728812093a44a75d6b70953311a48dab
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove a bunch of unused structure members that are just wasting
space. Remove a completely unused info structure definition as well.
Also update copyrights.
Change-ID: I028ab92d9b7bd13a832cf3363bd1dc6610d8a535
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the DOWN flag before attempting to disable VFs when unloading the
driver. Also, don't attempt to reset the VFs when the driver is
unloading, because the switch configuration will fail. This fixes a
panic on unload when VFs are enabled.
Change-ID: I25a6567e89c9687145f510ff4f630932412c5c5d
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If VFs are present when the driver loads, then set up some resources
so they can function.
Change-ID: I485916a811609a9990ce663d06dc645f625b07ff
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reset all of the VFs after a PF reset, so that they are in a known
state, and the VF driver can detect the reset and reinit itself.
Change-ID: I93c5b3a0f8b1371d0da078f92de948b9d3a6413f
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without this, the VF can never communicate with the PF after a VF
reset.
Change-ID: I8d10f1d0d0638d50d39f0aff263422e05d83ad83
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
