ULPI PHYs have a reset signal, and different boards use a different GPIO
for this task. Add a property to device tree to represent this.
I'm not sure if adding this property to the EHCI controller node is
entirely correct; perhaps eventually we should have explicit separate
nodes for the various PHYs. However, we don't have that right now, so this
binding seems like a reasonable choice.
Cc: <devicetree-discuss@lists.ozlabs.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: <linux-usb@vger.kernel.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Not all boards use GPIO_PV0 as the ULPI PHY reset signal. Instead of
hard-coding this GPIO into devices.c, make the board files set it
explicitly. This will allow the PHY code to differentiate between set and
unset values, and hence know when to read the value from device tree.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
pll_p_out4 is used on all/most Tegra boards to drive the cdev2 output pin
to provide a reference clock to a ULPI USB PHY. This reference clock must
run at 24MHz, and the cdev2 output has no additional dividers.
Remove board-paz00.c's now-duplicate initialization of this clock.
Reported-by: Marc Dietrich <marvin24@gmx.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Commit 40f9cf0 "ARM: tegra: reparent sclk to pll_c_out1" changed the
rate of hclk. Since pclk is derived from that, and only has integer
dividers, the pclk rate needs to change in the same fashion, from 54MHz
to 60MHz.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
pll_p_out4 needs to be used for other purposes. Reparent sclk so that
it runs from pll_c. Change sclk's rate to 120MHz from 108MHz since this
is the lowest precise rate that can be achieved by dividing the pll_c
rate without reducing the sclk rate. (600/5=120, 600/5.5=109.0909...,
600/6=100).
Signed-off-by: Stephen Warren <swarren@nvidia.com>
pll_c will be used as a clock source. Fill in tegra_pll_c_freq_table[]
so that it's possible to explicitly initialize the PLL.
NVIDIA's downstream nv-3.1 kernel and the ChromeOS kernel have different
pll_c tables. nv-3.1 contains entries for 522MHz and 598MHz output,
whereas the ChromeOS kernel contains entries for 600MHz output. I chose
to upstream the ChromeOS values for now, since the 600MHz rate appears
to match the default rate of this PLL when the HW boots, and it's not
clear to me why 522 or 598MHz are more useful.
Signed-off-by: Allen Martin <amartin@nvidia.com>
Signed-off-by: Olof Johansson <olofj@chromium.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
[swarren: wrote commit description]
Rather than having a single tegra-pinctrl driver that determines whether
it's running on Tegra20 or Tegra30, instead have separate drivers for
each that call into utility functions to implement the majority of the
driver. This change is based on review feedback of the SPEAr pinctrl
driver, which had originally copied to Tegra driver structure.
This requires that the two drivers have unique names. Update a couple
spots in arch/arm/mach-tegra for the name change.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
This adds a complete pinmux configuration to all Tegra20 device tree
files. This allows removal of board-dt-tegra20.c's use of the pinmux
board files, and the special device tree handling in board-pinmux.c.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
This adds a minimal pinmux configuration to the Tegra Cardhu device
tree. Initially, just the built-in eMMC and SD card slot are configured.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net
The pinctrl driver is now active and used by all boards. Remove the
old pinmux driver.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
* Rename old pinmux and new pinctrl platform driver and DT match table
entries, so the new driver gets instantiated.
* Re-write board-pinmux.c, so that it uses pinctrl APIs to configura the
pinmux.
* Re-write board-*-pinmux.c so that the pinmux configuration tables are
in pinctrl format.
Ventana's pin mux table needed some edits on top of the basic format
conversion, since some mux options that were previously marked as
reserved are now valid in the new pinctrl driver. Attempting to use the
old reserved names will result in a failure. Specifically, groups lpw0,
lpw2, lsc1, lsck, and lsda were changed from function rsvd4 to displaya,
and group pta was changed from function rsvd2 to hdmi.
All boards' pin mux tables needed some edits on top of the based format
conversion, since function i2c was split into i2c1 (first general I2C
controller) and i2cp (power I2C controller) to better align function
definitions with HW blocks.
Due to the split of mux tables into pure mux and pull/tristate tables,
many entries in the separate Seaboard/Ventana tables could be merged
into the common table, since the entries differed only in the portion
in one of the tables, not both.
Most pin groups allow configuration of mux, tri-state, and pull. However,
some don't allow pull configuration, which is instead configured by new
groups that only allow pull configuration. This is a reflection of the
true HW capabilities, which weren't fully represented by the old pinmux
driver. This required adding new pull table entries for those new groups,
and setting many other entries' pull configuration to
TEGRA_PINCONFIG_DONT_SET.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Recent pinctrl discussions concluded that gpiolib APIs should in fact do
whatever is required to mux a GPIO onto pins, by calling pinctrl APIs if
required. This change implements this for the Tegra GPIO driver, and removes
calls to the Tegra-specific APIs from drivers and board files.
Cc: Chris Ball <cjb@laptop.org>
Cc: linux-mmc@vger.kernel.org
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Chris Ball <cjb@laptop.org> # for sdhci-tegra.c
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Don't call gpio_request() or gpio_direction_input() for ISL29018_IRQ.
This pin is only used as an IRQ, and hence no GPIO configuration should
be necessary; the GPIO/IRQ driver should (and does) perform any required
setup when the IRQ is requested.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net>
Instead of having board files manually request and initialize USB VBUS
GPIOs, fill in the USB driver's platform data and have it do it.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net>
Add a vbus_gpio field to platform data. This mirrors the device tree
property nvidia,vbus-gpio. This makes the VBUS GPIO handling identical
between booting with board files and device tree; the driver always does
it.
This removes the need for board files to request and initialize the GPIO
early during their boot process, perhaps even before the GPIO driver is
ready to process the request.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net>
Pull ARM fixes from Russell King:
"Nothing too disasterous, the biggest thing being the removal of the
regulator support for vcore in the AMBA driver; only one SoC was using
this and it got broken during the last merge window, which then
started causing problems for other people. Mutual agreement was
reached for it to be removed."
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7386/1: jump_label: fixup for rename to static_key
ARM: 7384/1: ThumbEE: Disable userspace TEEHBR access for !CONFIG_ARM_THUMBEE
ARM: 7382/1: mm: truncate memory banks to fit in 4GB space for classic MMU
ARM: 7359/2: smp_twd: Only wait for reprogramming on active cpus
ARM: 7383/1: nommu: populate vectors page from paging_init
ARM: 7381/1: nommu: fix typo in mm/Kconfig
ARM: 7380/1: DT: do not add a zero-sized memory property
ARM: 7379/1: DT: fix atags_to_fdt() second call site
ARM: 7366/3: amba: Remove AMBA level regulator support
ARM: 7377/1: vic: re-read status register before dispatching each IRQ handler
ARM: 7368/1: fault.c: correct how the tsk->[maj|min]_flt gets incremented
c5905afb0 ("static keys: Introduce 'struct static_key'...") renamed
struct jump_label_key to struct static_key. Fixup ARM for this to
eliminate these build warnings:
include/linux/jump_label.h:113:2:
warning: passing argument 1 of 'arch_static_branch' from incompatible pointer type
include/asm/jump_label.h:17:82:
note: expected 'struct jump_label_key *' but argument is of type 'struct static_key *'
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Currently when ThumbEE is not enabled (!CONFIG_ARM_THUMBEE) the ThumbEE
register states are not saved/restored at context switch. The default state
of the ThumbEE Ctrl register (TEECR) allows userspace accesses to the
ThumbEE Base Handler register (TEEHBR). This can cause unexpected behaviour
when people use ThumbEE on !CONFIG_ARM_THUMBEE kernels, as well as allowing
covert communication - eg between userspace tasks running inside chroot
jails.
This patch sets up TEECR in order to prevent user-space access to TEEHBR
when !CONFIG_ARM_THUMBEE. In this case, tasks are sent SIGILL if they try to
access TEEHBR.
Cc: stable@vger.kernel.org
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Jonathan Austin <jonathan.austin@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If a bank of memory spanning the 4GB boundary is added on a !CONFIG_LPAE
kernel then we will hang early during boot since the memory bank will
have wrapped around to zero.
This patch truncates memory banks for !LPAE configurations when the end
address is not representable in 32 bits.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
During booting of cpu1, there is a short window where cpu1
is online, but not active where cpu1 is occupied by waiting
to become active. If cpu0 then decides to schedule something
on cpu1 and wait for it to complete, before cpu0 has set
cpu1 active, we have a deadlock.
Typically it's this CPU frequency transition that happens at
this time, so let's just not wait for it to happen, it will
happen whenever the CPU eventually comes online instead.
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: stable@kernel.org
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Reviewed-by: Rickard Andersson <rickard.andersson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Now that we have OPP layer, and OMAP CPUfreq driver is using it, we no
longer need/use the clock framework code for filling up CPUfreq
tables. Remove it.
Removing this code also eliminates build errors when CPU_FREQ_TABLE
support is not enabled.
Thanks to Russell King for pointing out the parts I missed under
plat-omap in the original version and also pointing out the build
errors when CPUFREQ_TABLE support was not enabled.
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
These were incorrectly introduced and can cause problems for of_irq_init.
The correct way to define a root controller is no interrupt-parent set at
all or the interrupt-parent is set to the root controller itself when
inherited from a parent node.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Tested-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Add config dependency for Exynos4 and Exynos5 device tree enabled machine
files on config options ARCH_EXYNOS4 and ARCH_EXYNOS5 respectively.
Enabling machine support without proper ARCH support enabled is incorrect.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The atmel_mxt_ts driver has been extended to support more 'configuration
objects' in commit 81c88a711 ("Input: atmel_mxt_ts - update object list"),
what broke the configuration values for NURI board. These values are
optional anyway, so remove them to get the driver working correctly.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
On some versions of NURI and UniversalC210 boards, camera clocks are
routed directly to xusbxti clock source. This patch sets the correct
value for this clock to let usb and camera sensors to work correctly and
avoid division by zero on driver's probe.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Regulator names should not contain slash to avoid issues with debugfs.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
When selecting SAMSUNG_PM_DEBUG, it complains about a missing printascii()
function if you do not select DEBUG_LL, so make the former select the latter.
Signed-off-by: Maurus Cuelenaere <mcuelenaere@gmail.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The change
commit 4416e9eb0b
Author: Gregory Bean <gbean@codeaurora.org>
Date: Wed Jul 28 10:22:12 2010 -0700
arm: msm: Fix section mismatch in smd.c.
fixes a section mismatch between the board file and the smd driver's
probe function, however, it misses the additional mismatches between
the probe function and some routines it calls. Fix these up as well.
Signed-off-by: David Brown <davidb@codeaurora.org>
Fixes the following warnings,
arch/arm/mach-msm/board-trout.c: In function 'trout_init':
arch/arm/mach-msm/board-trout.c:71: error: 'system_rev' undeclared (first use in this function)
arch/arm/mach-msm/board-trout.c:71: error: (Each undeclared identifier is reported only once
arch/arm/mach-msm/board-trout.c:71: error: for each function it appears in.)
and
arch/arm/mach-msm/board-trout-panel.c: In function 'trout_init_panel':
arch/arm/mach-msm/board-trout-panel.c:267: error: 'system_rev' undeclared (first use in this function)
arch/arm/mach-msm/board-trout-panel.c:267: error: (Each undeclared identifier is reported only once
arch/arm/mach-msm/board-trout-panel.c:267: error: for each function it appears in.)
This came in with the following commit 9f97da78bf
which removes asm/system.h
Signed-off-by: Daniel Walker <dwalker@fifo99.com>
cc: David Howells <dhowells@redhat.com>
cc: Bryan Huntsman <bryanh@codeaurora.org>
cc: linux-arm-msm@vger.kernel.org
cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: David Brown <davidb@codeaurora.org>
This old fixup causes a build failure, so I remove it just like in
trout.
Signed-off-by: Daniel Walker <dwalker@fifo99.com>
Signed-off-by: David Brown <davidb@codeaurora.org>
Commit 94e5a85b ("ARM: earlier initialization of vectors page") made it
the responsibility of paging_init to initialise the vectors page.
This patch adds a call to early_trap_init for the !CONFIG_MMU case,
placing the vectors at CONFIG_VECTORS_BASE.
Cc: Jonathan Austin <jonathan.austin@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The description for the CPU_HIGH_VECTOR Kconfig option for nommu builds
doesn't make any sense.
This patch fixes up the trivial grammatical error.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Some bootloaders are broken enough to expose an ATAG_MEM with
a null size. Converting such tag to a memory node leads to
an unbootable system.
Skip over zero sized ATAG_MEM to avoid this situation.
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
atags_to_fdt() returns 1 when it fails to find a valid FDT signature.
The CONFIG_ARM_ATAG_DTB_COMPAT code is supposed to retry with another
location, but only does so when the initial call doesn't fail.
Fix this by using the correct condition in the assembly code.
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add PDMA and MDMA physical base address macros which is
require for EXYNOS5 of_dev_auxdata setup.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
[kgene.kim@samsung.com: changed dma channel fo mdma1]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Fixes the following warning:
warning: 'dma_dmamask' defined but not used [-Wunused-variable]
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
handle_IRQ may briefly cause interrupts to be re-enabled during soft IRQ
processing on the exit path, leading to nested handling of VIC interrupts.
Since the current code does not re-read the VIC_IRQ_STATUS register, this
can lead to multiple invocations of the same interrupt handler and
spurious interrupts to be reported.
This patch changes the VIC interrupt dispatching code to re-read the
status register each time, avoiding duplicate invocations of the same
handler.
Acked-and-Tested-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
commit 8878a539ff was done by me
to make the page fault handler retryable as well as interruptible.
Due to this commit, there is a mistake in the way in which
tsk->[maj|min]_flt counter gets incremented for VM_FAULT_ERROR:
If VM_FAULT_ERROR is returned in the fault flags by handle_mm_fault,
then either maj_flt or min_flt will get incremented. This is wrong
as in the case of a VM_FAULT_ERROR we need to be skip ahead to the
error handling code in do_page_fault.
Added a check after the call to __do_page_fault() to check for
(fault & VM_FAULT_ERROR).
Signed-off-by: Kautuk Consul <consul.kautuk@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch is omitted in v2 patch of Jaecheol Lee.
drivers/cpufreq/exynos5250-cpufreq.c: In function 'set_clkdiv':
drivers/cpufreq/exynos5250-cpufreq.c:144: error: 'EXYNOS5_CLKDIV_STATCPU0' undeclared (first use in this function)
drivers/cpufreq/exynos5250-cpufreq.c:144: error: (Each undeclared identifier is reported only once
drivers/cpufreq/exynos5250-cpufreq.c:144: error: for each function it appears in.)
drivers/cpufreq/exynos5250-cpufreq.c:150: error: 'EXYNOS5_CLKDIV_CPU1' undeclared (first use in this function)
drivers/cpufreq/exynos5250-cpufreq.c:152: error: 'EXYNOS5_CLKDIV_STATCPU1' undeclared (first use in this function)
drivers/cpufreq/exynos5250-cpufreq.c: In function 'set_apll':
drivers/cpufreq/exynos5250-cpufreq.c:166: error: 'EXYNOS5_CLKMUX_STATCPU' undeclared (first use in this function)
drivers/cpufreq/exynos5250-cpufreq.c:173: error: 'EXYNOS5_APLL_LOCK' undeclared (first use in this function)
drivers/cpufreq/exynos5250-cpufreq.c: In function 'exynos5250_cpufreq_init':
drivers/cpufreq/exynos5250-cpufreq.c:312: error: 'EXYNOS5_CLKDIV_CPU1' undeclared (first use in this function)
Cc: Jaecheol Lee <jc.lee@samsung.com>
Signed-off-by: Jonghwan Choi <jhbird.choi@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This fixes following build error when sound support is selected
on EXYNOS4 platform.
sound/soc/samsung/idma.c: In function ‘idma_close’:
sound/soc/samsung/idma.c:327:11: error: ‘IRQ_I2S0’ undeclared (first use in this function)
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
According to commit 719a4240("mfd: Remove unused LDO supply field
from WM8994 pdata"), the LDO supply field should be removed from
the initializer.
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
A bunch of fixes for regressions (and a few other problems) in 3.4-rc1:
* Fix for regression of mach/io.h cleanup on platforms with PCI or PCMCIA
(adding back the include file on those for now)
* AT91 fixes for usb and spi
* smsc911x ethernet fixes for i.MX
* smsc911x fixes for OMAP
* gpio fixes for Tegra
* A handful of build error and warning fixes for various platforms
* cpufreq kconfig dependencies, build and lowlevel debug fixes for
Samsung platforms
In other words, more or less the regular collection of -rc1/2 type
material. A few of them, in particular the smsc911x for OMAP series, aren't
technically regressions for 3.4, but they're valid fixes and we're still
relatively early in the rc cycle so it seems appropriate to include them.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJPfmp2AAoJEIwa5zzehBx31hAP/Rs3xdpOpwtPt0YKnvtg5/k7
FyZuhrhihPd2+hJKpzUVPmaal0TdyWgt2kGCl13JrwqWu7xV6VMDakrBPAl/jXwb
3NJU2zjfx+6YJMbgSxid2f/Gv36/p7bBusqGWiU92vOly0Tw4joqZ8ABoO4ti8mK
O1eGbS6Rw5rpHy2u0UkgK3r9xCQxmSJQ1hCezOm7cWmwEhC5pmDe9qKO3Qdbp8tr
XdIE3v0qSv5TuQdPedh8+3JsSx5mub+ZYKKqzWIrbQW5xrqawOKXl4nugrNnustr
aDIoHpAoo4++qt0WJY2wg4/hHoPj2ibHzZqWhktmWj4leMttwTUFnHZm3wvZ55fA
0kp4x6pCsa7J1FhYhCpUVZUS/CcQv8wKBA7RGGUsl/0t52droqFwfYi/YhB6nCMo
zDRHJm+hToZN1/HPiKsyFlM+pQ2nsE/AXs7V5ohf7/GE6w66A5TU/HHolHv3ERvU
QoshX3zPtrAUQEe8WT4bG7HqXaNr/aa080ElYSdlVQ/HfGbIcKcSxzavUvZIZmx2
IYFF3SkpAhVtidcPzdnYJPjNF9c3Kr1w0QLUGgyRkrRp6OSPiPkksmI8gcjlf5l3
runmq36+ktqSz1KnNHBNnSF9aQ6drzCNQ7nqpPXeMaTrZ1jdXNcKTw9eLo/Kr3vB
4UHuqt8hfrcpiUYdXRQ1
=RVTD
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull "ARM: SoC fixes: from Olof Johansson:
"A bunch of fixes for regressions (and a few other problems) in
3.4-rc1:
- Fix for regression of mach/io.h cleanup on platforms with PCI or
PCMCIA (adding back the include file on those for now)
- AT91 fixes for usb and spi
- smsc911x ethernet fixes for i.MX
- smsc911x fixes for OMAP
- gpio fixes for Tegra
- A handful of build error and warning fixes for various platforms
- cpufreq kconfig dependencies, build and lowlevel debug fixes for
Samsung platforms
In other words, more or less the regular collection of -rc1/2 type
material. A few of them, in particular the smsc911x for OMAP series,
aren't technically regressions for 3.4, but they're valid fixes and
we're still relatively early in the rc cycle so it seems appropriate
to include them."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (60 commits)
ARM: fix __io macro for PCMCIA
ARM: EXYNOS: Fix compiler warning in dma.c file
ARM: EXYNOS: fix ISO C90 warning
ARM: OMAP2+: hwmod: Fix wrong SYSC_TYPE1_XXX_MASK bit definitions
ARM: OMAP2+: hwmod: Make omap_hwmod_softreset wait for reset status
ARM: OMAP2+: hwmod: Restore sysc after a reset
ARM: OMAP2+: omap_hwmod: Allow io_ring wakeup configuration for all modules
ARM: OMAP3: clock data: fill in some missing clockdomains
ARM: OMAP4: clock data: Force a DPLL clkdm/pwrdm ON before a relock
ARM: OMAP4: clock data: fix mult and div mask for USB_DPLL
ARM: OMAP2+: powerdomain: Wait for powerdomain transition in pwrdm_state_switch()
gpio: tegra: Iterate over the correct number of banks
gpio: tegra: fix register address calculations for Tegra30
EXYNOS: fix dependency for EXYNOS_CPUFREQ
ARM: at91: dt: remove unit-address part for memory nodes
ARM: at91: fix check of valid GPIO for SPI and USB
USB: ehci-atmel: add needed of.h header file
ARM: at91/NAND DT bindings: add comments
ARM: at91/at91sam9x5.dtsi: fix NAND ale/cle in DT file
USB: ohci-at91: trivial return code name change
...
early v3.4-rc series. Also contains an HSMMC integration refinement
of an earlier hardware bug workaround.
ARM: OMAP3: clock data: fill in some missing clockdomains
ARM: OMAP4: clock data: Force a DPLL clkdm/pwrdm ON before a relock
ARM: OMAP4: clock data: fix mult and div mask for USB_DPLL
ARM: OMAP2+: powerdomain: Wait for powerdomain transition in pwrdm_state_switch()
ARM: OMAP AM3517/3505: clock data: change EMAC clocks aliases
ARM: OMAP2+: hwmod: Fix wrong SYSC_TYPE1_XXX_MASK bit definitions
ARM: OMAP2+: hwmod: Make omap_hwmod_softreset wait for reset status
ARM: OMAP2+: hwmod: Restore sysc after a reset
ARM: OMAP: clock: fix race in disable all clocks
ARM: OMAP4: hwmod data: Add aliases for McBSP fclk clocks
ARM: OMAP2+: omap_hwmod: Allow io_ring wakeup configuration for all modules
ARM: OMAP3xxx: clock data: fix DPLL4 CLKSEL masks
ARM: OMAP3xxx: HSMMC: avoid erratum workaround when transceiver is attached
ARM: OMAP44xx: clockdomain data: correct the emu_sys_clkdm CLKTRCTRL data
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=41FI
-----END PGP SIGNATURE-----
Merge tag 'omap-fixes-a2-for-3.4rc' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into fixes
From Paul Walmsley:
OMAP clock, powerdomain, clockdomain, and hwmod fixes intended for the
early v3.4-rc series. Also contains an HSMMC integration refinement
of an earlier hardware bug workaround.
* tag 'omap-fixes-a2-for-3.4rc' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending:
ARM: OMAP2+: hwmod: Fix wrong SYSC_TYPE1_XXX_MASK bit definitions
ARM: OMAP2+: hwmod: Make omap_hwmod_softreset wait for reset status
ARM: OMAP2+: hwmod: Restore sysc after a reset
ARM: OMAP2+: omap_hwmod: Allow io_ring wakeup configuration for all modules
ARM: OMAP3: clock data: fill in some missing clockdomains
ARM: OMAP4: clock data: Force a DPLL clkdm/pwrdm ON before a relock
ARM: OMAP4: clock data: fix mult and div mask for USB_DPLL
ARM: OMAP2+: powerdomain: Wait for powerdomain transition in pwrdm_state_switch()
ARM: OMAP AM3517/3505: clock data: change EMAC clocks aliases
ARM: OMAP: clock: fix race in disable all clocks
ARM: OMAP4: hwmod data: Add aliases for McBSP fclk clocks
ARM: OMAP3xxx: clock data: fix DPLL4 CLKSEL masks
ARM: OMAP3xxx: HSMMC: avoid erratum workaround when transceiver is attached
ARM: OMAP44xx: clockdomain data: correct the emu_sys_clkdm CLKTRCTRL data
Merge batch of fixes from Andrew Morton:
"The simple_open() cleanup was held back while I wanted for laggards to
merge things.
I still need to send a few checkpoint/restore patches. I've been
wobbly about merging them because I'm wobbly about the overall
prospects for success of the project. But after speaking with Pavel
at the LSF conference, it sounds like they're further toward
completion than I feared - apparently davem is at the "has stopped
complaining" stage regarding the net changes. So I need to go back
and re-review those patchs and their (lengthy) discussion."
* emailed from Andrew Morton <akpm@linux-foundation.org>: (16 patches)
memcg swap: use mem_cgroup_uncharge_swap fix
backlight: add driver for DA9052/53 PMIC v1
C6X: use set_current_blocked() and block_sigmask()
MAINTAINERS: add entry for sparse checker
MAINTAINERS: fix REMOTEPROC F: typo
alpha: use set_current_blocked() and block_sigmask()
simple_open: automatically convert to simple_open()
scripts/coccinelle/api/simple_open.cocci: semantic patch for simple_open()
libfs: add simple_open()
hugetlbfs: remove unregister_filesystem() when initializing module
drivers/rtc/rtc-88pm860x.c: fix rtc irq enable callback
fs/xattr.c:setxattr(): improve handling of allocation failures
fs/xattr.c:listxattr(): fall back to vmalloc() if kmalloc() failed
fs/xattr.c: suppress page allocation failure warnings from sys_listxattr()
sysrq: use SEND_SIG_FORCED instead of force_sig()
proc: fix mount -t proc -o AAA
Many users of debugfs copy the implementation of default_open() when
they want to support a custom read/write function op. This leads to a
proliferation of the default_open() implementation across the entire
tree.
Now that the common implementation has been consolidated into libfs we
can replace all the users of this function with simple_open().
This replacement was done with the following semantic patch:
<smpl>
@ open @
identifier open_f != simple_open;
identifier i, f;
@@
-int open_f(struct inode *i, struct file *f)
-{
(
-if (i->i_private)
-f->private_data = i->i_private;
|
-f->private_data = i->i_private;
)
-return 0;
-}
@ has_open depends on open @
identifier fops;
identifier open.open_f;
@@
struct file_operations fops = {
...
-.open = open_f,
+.open = simple_open,
...
};
</smpl>
[akpm@linux-foundation.org: checkpatch fixes]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With commit c334bc1 (ARM: make mach/io.h include optional), PCMCIA was
broken. PCMCIA depends on __io() returning a valid i/o address, and most
ARM platforms require IO_SPACE_LIMIT be set to 0xffffffff for PCMCIA. This
needs a better fix with a fixed i/o address mapping, but for now we just
restore things to the previous behavior.
This fixes at91, omap1, pxa and sa11xx. pxa needs io.h if PCI is enabled,
but PCMCIA is not. sa11xx already has IO_SPACE_LIMIT set to 0xffffffff,
so it doesn't need an io.h.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Joachim Eastwood <joachim.eastwood@jotron.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Andrew Victor <linux@maxim.org.za>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Tested-by: Paul Parsons <lost.distance@yahoo.com> (pxa270)
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
From Tony Lindgren:
Note that this also contains a set of fixes that are not regressions
or oopses to properly deal with the smsc911x regulator issue.
Basically the regulators must be per board file as the regulators
can also come from drivers, such as twl4030. So it's best to dumb
down gpmc-smsc911x.c to not even care about the regulators.
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP: fix section mismatches in usb-host.c
ARM: OMAP2+: Fix omap2+ build error
ARM: OMAP2+: smsc911x: Add fixed board regulators
ARM: OMAP2+: smsc911x: Remove regulator support from gmpc-smsc911x
ARM: OMAP2+: smsc911x: Remove unused rate calculation
ARM: OMAP2+ smsc911x: Fix possible stale smsc911x flags
ARM: OMAP2+: smsc911x: Remove odd gpmc_cfg/board_data redirection
ARM: OMAP3+: fix oops triggered in omap_prcm_register_chain_handler(v1)
ARM: OMAP2+: OPP: allow OPP enumeration to continue if device is not present
arm: omap3: pm34xx.c: Replace printk() with appropriate pr_*()
arm: omap3: pm34xx.c: Fix omap3_pm_init() error out paths
ARM: OMAP4: Workaround the OCP synchronisation issue with 32K synctimer.
ARM: OMAP4: prm: fix interrupt register offsets
ARM: OMAP: hwmod: Use sysc_fields->srst_shift and get rid of hardcoded SYSC_TYPE2_SOFTRESET_MASK
