synaptics_profile_sensor_process() and synaptics_report_mt_data() now
share the exact same code. Remove one implementation and rely on the
other where it was used.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The current code tries to consider all states and transitions to properly
detect which finger is attached to which slot. The code is quite huge
and difficult to read.
If the sensor manages to group the touch points but is not reliable in
giving tracking ids, we can simply use the kernel tracking method. Note
that it is already used by Cr-48 Chromebooks.
Incidentaly, this fixes a bug reported by Peter Hutterer:
"""
on the Lenovo T440, run:
evemu-record /dev/input/event4 | grep BTN_
then put one, two, three, two fingers down
when you go from 3 to 2 fingers the driver sends a spurious BTN_TOUCH 0
event:
E: 0.000000 0001 014a 0001 # EV_KEY / BTN_TOUCH 1
E: 0.000000 0001 0145 0001 # EV_KEY / BTN_TOOL_FINGER 1
E: 0.770008 0001 0145 0000 # EV_KEY / BTN_TOOL_FINGER 0
E: 0.770008 0001 014d 0001 # EV_KEY / BTN_TOOL_DOUBLETAP 1
E: 1.924716 0001 014d 0000 # EV_KEY / BTN_TOOL_DOUBLETAP 0
E: 1.924716 0001 014e 0001 # EV_KEY / BTN_TOOL_TRIPLETAP 1
.. changing from 3 to 2 fingers now
E: 3.152641 0001 014a 0000 # EV_KEY / BTN_TOUCH 0
E: 3.152641 0001 014d 0001 # EV_KEY / BTN_TOOL_DOUBLETAP 1
E: 3.152641 0001 014e 0000 # EV_KEY / BTN_TOOL_TRIPLETAP 0
E: 3.176948 0001 014a 0001 # EV_KEY / BTN_TOUCH 1
quick look in the kernel shows it's caused by hw.z going to 0 for a packet,
so probably a firmware bug. either way, it makes it hard to track BTN_TOUCH
as signal that at least one finger is down.
"""
The in-kernel tracking is enough to remove this spurious BTN_TOUCH 0.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Most of the protocol for these touchpads has been reverse engineered. This
commit adds a basic multitouch-capable driver.
A lot of the protocol is still unknown. Especially, we don't know how to
identify the device yet apart from the PNP ID.
The previous workaround for these devices has been left in place in case
the driver is not compiled into the kernel or in case some other device
with the same PNP ID is not recognized by the driver yet still has the same
problems with the device probing code.
Signed-off-by: Mathias Gottschlag <mgottschlag@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add a table documenting where all the bits are in the v7 touchpad packets.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Protocol v7 uses the middle / right button bits on clickpads to communicate
"location" information of a 3th touch (and possible 4th) touch on
clickpads.
Specifically when 3 touches are down, if one of the 3 touches is in the
left / right button area, this will get reported in the middle / right
button bits and the touchpad will still send a TWO type packet rather then
a MULTI type packet, so when this happens we must add the finger reported
in the button area to the finger count.
Likewise we must also add fingers reported this way to the finger count
when we get MULTI packets.
BugLink: https://bugs.freedesktop.org/show_bug.cgi?id=86338
Cc: stable@vger.kernel.org # 3.17
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The v7 proto differentiates between a primary touch (with high precision)
and a secondary touch (with lower precision). Normally when 2 fingers are
down and one is lifted the still present touch becomes the primary touch,
but some traces have shown that this does not happen always.
This commit deals with this by making alps_get_mt_count() not stop at the
first empty mt slot, and if a touch is present in mt[1] and not mt[0]
moving the data to mt[0] (for input_mt_assign_slots).
BugLink: https://bugs.freedesktop.org/show_bug.cgi?id=86338
Cc: stable@vger.kernel.org # 3.17
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
NEW packets are send to indicate a discontinuity in the finger coordinate
reporting. Specifically a finger may have moved from slot 0 to 1 or vice
versa. INPUT_MT_TRACK takes care of this for us.
NEW packets have 3 problems:
1) They do not contain middle / right button info (on non clickpads)
this can be worked around by preserving the old button state
2) They do not contain an accurate fingercount, and they are
typically send when the number of fingers changes. We cannot use
the old finger count as that may mismatch with the amount of
touch coordinates we've available in the NEW packet
3) Their x data for the second touch is inaccurate leading to
a possible jump of the x coordinate by 16 units when the first
non NEW packet comes in
Since problems 2 & 3 cannot be worked around, just ignore them.
BugLink: https://bugs.freedesktop.org/show_bug.cgi?id=86338
Cc: stable@vger.kernel.org # 3.17
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
IBM Trackpoints have a feature to compensate for drift by recalibrating
themselves periodically. By default, if for 0.5 seconds there is no change
in position, it's used as the new zero. This duration is too low. Often,
the calibration happens when the trackpoint is in fact being used.
IBM's Trackpoint Engineering Specifications show a configuration register
that allows changing this duration, rstdft1.
Expose it via sysfs among the other settings.
Signed-off-by: Mike Murdoch <main.haarp@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Let's use 'error' variable instead of 'ret' when we need to store erro
codes.
Signed-off-by: Dudley Du <dudley.dulixin@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Chage b1cfa7b438 tried to get away form using
irq in cyapa structure and use client->irq instead, but missed a couple of
spots making the touchpad inoperative after resume.
Reported-by: Jeremiah Mahler <jmmahler@gmail.com>
Signed-off-by: Dudley Du <dudley.dulixin@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use of managed resources simplifies error handling and device removal code.
Signed-off-by: Dudley Du <dudl@cypress.com>
[Dmitry: added open/close methods so cyapa_remove is no longer needed.]
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
For functions defined in header files we should use static inline rather
than inline, which breaks under the latest upstream gcc (which is really
gcc issue, but static inline is better suited regardless).
The related error (with allmodconfig under tile):
MODPOST 4002 modules
ERROR: "lifebook_detect" [drivers/input/mouse/psmouse.ko] undefined!
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use __maybe_unused instead of ifdef guards around suspend/resume
functions, in order to increase build coverage and fix build warnings.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This driver supports Elan I2C/SMbus touchpads found in some laptops and
also in many Chromebooks.
Signed-off-by: Duson Lin <dusonlin@emc.com.tw>
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Unfortunately, ForcePad capability is not actually exported over PS/2, so
we have to resort to DMI checks.
Cc: stable@vger.kernel.org
Reported-by: Nicole Faerber <nicole.faerber@kernelconcepts.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUMZqoAAoJEHm+PkMAQRiGFC4H/i0b9vxCwe6VCXonpaDW03fI
JKE7v/zwDfhDngKSYfBWRSf3jXwfSHLvAvCgIvqTw5qBW3XSWF8xB7kJpWptQxIi
M6ePfaETt2mPYhEWWWxJK8boykiOXObDrFJVhfjHGsjbvmKiLPMaGYwXTSwZJ32V
fQDaA9Piugjc9wEY0d+6cjqUUEwlb4+GFz4Wv2oJgbpzxwgJS/XjQYk+3PrcdAXz
lmwPXQ+6ntJaducVu3JM2YYvaJLzTw+T+MPsWiTvaE4ILmuiw492VNY5XdyQQtb2
DSActOKCF2hIwnG+DMg63XV5FH81HqczwORDygBuxko0cURxupxMnaLPkVRpksk=
=+PRQ
-----END PGP SIGNATURE-----
Merge tag 'v3.17' into next
Synchronize with mainline to bring in changes to Synaptics and i8042
drivers.
The Asus X450 and X550 laptops use a PS/2 touchpad from a new
manufacturer called FocalTech:
https://bugzilla.kernel.org/show_bug.cgi?id=77391https://bugzilla.redhat.com/show_bug.cgi?id=1110011
The protocol for these devices is not known at this time, but even
without knowing the protocol they need some special handling. They get
upset by some of our other PS/2 device probing, and once upset generate
random mouse events making things unusable even with an external mouse.
This patch adds detection of these devices based on their pnp ids, and
when they are detected, treats them as a bare ps/2 mouse. Doing things
this way they at least work in their ps/2 mouse emulation mode.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The matches_pnp_id function from the synaptics driver is useful for other
drivers too. Make it a generic psmouse helper function.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
ForcePads are found on HP EliteBook 1040 laptops. They lack any kind of
physical buttons, instead they generate primary button click when user
presses somewhat hard on the surface of the touchpad. Unfortunately they
also report primary button click whenever there are 2 or more contacts
on the pad, messing up all multi-finger gestures (2-finger scrolling,
multi-finger tapping, etc). To cope with this behavior we introduce a
delay (currently 50 msecs) in reporting primary press in case more
contacts appear.
Cc: stable@vger.kernel.org
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
I've not done a full audit of all mouse drivers, I noticed these ones were
missing the POINTER property while working on the POINTING_STICK property.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
It is useful for userspace to know that there not dealing with a regular
mouse but rather with a pointing stick (e.g. a trackpoint) so that
userspace can e.g. automatically enable middle button scrollwheel
emulation.
It is impossible to tell the difference from the evdev info without
resorting to putting a list of device / driver names in userspace, this is
undesirable.
Add a property which allows userspace to see if a device is a pointing
stick, and set it on all the pointing stick drivers.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Some elantech v3 touchpad equipped laptops also have a trackpoint, before
this commit, these give sync errors. With this patch, the trackpoint is
provided as another input device: 'Elantech PS/2 TrackPoint'
The patch will also output messages that do not follow the expected pattern.
In the mean time I've seen 2 unknown packets occasionally:
0x04 , 0x00 , 0x00 , 0x00 , 0x00 , 0x00
0x00 , 0x00 , 0x00 , 0x02 , 0x00 , 0x00
I don't know what those are for, but they can be safely ignored.
Currently all packets that are not known to v3 touchpad and where
packet[3] (the fourth byte) lowest nibble is 6 are now recognized as
PACKET_TRACKPOINT and processed by the new elantech_report_trackpoint.
This has been verified to work on a laptop Lenovo L530 where the
touchpad/trackpoint combined identify themselves as:
psmouse serio1: elantech: assuming hardware version 3 (with firmware version 0x350f02)
psmouse serio1: elantech: Synaptics capabilities query result 0xb9, 0x15, 0x0c.
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ulrik De Bie <ulrik.debie-os@e2big.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
elantech_init() calls elantech_set_absolute_mode which sets the driver in
an absolute mode. When after this the elantech_init fails, it is best to
turn the ps/2 mouse emulation mode back on by calling psmouse_reset() so
that it can work as a regular mouse.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ulrik De Bie <ulrik.debie-os@e2big.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When we fail to match data returned by E7 and EC reports we state that we
found "Unknown ALPS touchpad" whereas it is most likely it is not ALPS
touchpad at all. Change wording a bit and reduce the message to debug so
that it does not litter users logs and confuse them.
Reported-by: Paul Menzel <paulepanter@users.sourceforge.net>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The profile sensor clickpad in a Cr-48 Chromebook does a reasonable job
of tracking individual fingers. This tracking isn't perfect, but,
experiments show that it works better than just passing "semi-mt" data
to userspace, and making userspace try to deduce where the fingers are
given a bounding box.
This patch tries to report correct two-finger positions instead of the
{(min_x, min_y), (max_x, max_y)} for profile sensor clickpads on Cr-48
chromebooks. Note that this device's firmware always reports the higher
(smaller y) finger in the "sgm" packet, and the lower (larger y) finger
in the "agm" packet. Thus, when a new finger arrives on the pad, the
kernel driver uses input core's contact tracking facilities to match
contacts with slots.
Inspired by patch by Daniel Kurtz <djkurtz@chromium.org> and Chung-yih
Wang <cywang@chromium.org>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Semi-MT devices are pointers too, so let's tell that to
input_mt_init_slots(), as well as let it set up the devices as semi-MT,
instead of us doing it manually.
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add support for querying the physical size from the touchpad for Rushmore
and v7 touchpads, and use that to tell userspace the device resolution.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Such as found on the new Toshiba Portégé Z30-A and Z40-A.
Signed-off-by: Yunkang Tang <yunkang.tang@cn.alps.com>
[hdegoede@redhat.com: Remove softbutton handling, this is done in userspace]
[hdegoede@redhat.com: Report INPUT_PROP_BUTTONPAD]
[hdegoede@redhat.com: Do not report fake PRESSURE, reporting BTN_TOUCH is
enough]
[hdegoede@redhat.com: Various cleanups / refactoring]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
So that decode functions can return a failure when appropriate.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
If we detect more then 2 fingers report 2 touches, rather then only
reporting the upper left corner of the bounding box.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Move all the semi-mt specific handling shared between the v3 and v4
handling code to a common helper function.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
For v3 protocol devices, use the more accurate single touch data when the
mt data contains only one finger. Note the mt data reporting a finger count
of 1 should never happen, but better safe then sorry.
This brings the v3 bitmap handling in line with what the v4 code does,
allowing to factor out the common bits into a helper function.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When there are 2 fingers on the pad we don't know which one is which, so
use input_mt_assign_slots to make sure the right set of coordinates ends
up in the right slot.
Besides ensuring things end up in the right slot, this also results in a
nice cleanup, since sync_frame also handles non mt position and btn_touch
reporting.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This is a preparation patch for switching the DIY mt handling to using
input_mt_assign_slots && input_mt_sync_frame.
struct alps_fields is quite large, so while making changes to almost all uses
of it lets put it in our priv data instead of on the stack.
Having it in our priv data also allows using it directly for storing values
which need to be cached, rather then having separate x, y, z, fingers, etc.
copies in our priv data.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This fixes 2 fingers at the same height or width on the touchpad getting
reported at different y / x coordinates.
Note num_bits is always at least 1.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
alps_process_bitmap was resetting the point bit-count as soon as it saw
2 0 bits in a row. This means that unless the high point actually is at
the end of the bitmap, it would always get its num_bits set to 0.
Instead reset num_bits to 0 on a 0->1 transition, so that with > 2 fingers
we only count the number of bits occupied by the highest finger.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Factor out the identical code for getting the bitmap points for x and y into
a helper function.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Rushmore models don't have the Y-axis data in the bitmap inverted. Since
we now have 2 different Y orientations, make the Y bitmap data processing
use a forward loop like the X bitmap data processing, unifying the 2,
and invert the data later, except on Rushmore.
So far no-one has noticed this because the synaptics driver only uses the
non mt coordinates (except on clickpads, and there are no alps clickpads
using process_bitmap).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
V3 models only report mt bitmap data when there are 2 or more fingers on
the touchpad. So always generate 2 positions in alps_process_bitmap, and
for v3 models only fall back to st data when there was no mt data in a
mt packet (which should never happen).
This fixes 2 finger scrolling not working when using 2 fingers close to
each other.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
commit 421e08c41f fixed the reported min/max for the X and Y axis,
but unfortunately, it broke the resolution of those same axis.
On the t540p, the resolution is the same regarding X and Y. It is not
a problem for xf86-input-synaptics because this driver is only interested
in the ratio between X and Y.
Unfortunately, xf86-input-cmt uses directly the resolution, and having a
null resolution leads to some divide by 0 errors, which are translated by
-infinity in the resulting coordinates.
Reported-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The touchpad on the GIGABYTE U2442 not only stops communicating when we try
to set bit 3 (enable real hardware resolution) of reg_10, but on some BIOS
versions also when we set bit 1 (enable two finger mode auto correct).
I've asked the original reporter of:
https://bugzilla.kernel.org/show_bug.cgi?id=61151
To check that not setting bit 1 does not lead to any adverse effects on his
model / BIOS revision, and it does not, so this commit fixes the touchpad
not working on these versions by simply never setting bit 1 for laptop
models with the no_hw_res quirk.
Reported-and-tested-by: James Lademann <jwlademann@gmail.com>
Tested-by: Philipp Wolfer <ph.wolfer@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
At least the Dell Vostro 5470 elantech *clickpad* reports right button
clicks when clicked in the right bottom area:
https://bugzilla.redhat.com/show_bug.cgi?id=1103528
This is different from how (elantech) clickpads normally operate, normally
no matter where the user clicks on the pad the pad always reports a left
button event, since there is only 1 hardware button beneath the path.
It looks like Dell has put 2 buttons under the pad, one under each bottom
corner, causing this.
Since this however still clearly is a real clickpad hardware-wise, we still
want to report it as such to userspace, so that things like finger movement
in the bottom area can be properly ignored as it should be on clickpads.
So deal with this weirdness by simply mapping a right click to a left click
on elantech clickpads. As an added advantage this is something which we can
simply do on all elantech clickpads, so no need to add special quirks for
this weird model.
Reported-and-tested-by: Elder Marco <eldermarco@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Most of the affected models share pnp-ids for the touchpad. So switching
to pnp-ids give us 2 advantages:
1) It shrinks the quirk list
2) It will lower the new quirk addition frequency, ie the recently added W540
quirk would not have been necessary since it uses the same LEN0034 pnp ids
as other models already added before it
As an added bonus it actually puts the quirk on the actual psmouse, rather
then on the machine, which is technically more correct.
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
