Add rk806 support to the existing rk808 regulator
driver.
This has been implemented using shengfei Xu's rk806
specific driver from the vendor tree as reference.
Co-developed-by: shengfei Xu <xsf@rock-chips.com>
Signed-off-by: shengfei Xu <xsf@rock-chips.com>
Reviewed-by: Matti Vaittinen <mazziesaccount@gmail.com>
Tested-by: Diederik de Haas <didi.debian@cknow.org> # Rock64, Quartz64 Model A + B
Tested-by: Vincent Legoll <vincent.legoll@gmail.com> # Pine64 QuartzPro64
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20230504173618.142075-15-sebastian.reichel@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The rk808 driver registers a bunch of regulator devices in a loop.
If one of the later regulators fails to register (usually because
its input supply is not yet available) everything will be unrolled
(i.e. previously registered regulators will be unregistered). With
asynchronous registration there might already be consumers, though.
We do not have the necessary infrastructure to properly unregister
the consumer device, so this scenario should be avoided.
First checking all input supplies or disallowing usage of the regulators
until all are registered does not work, since there can be
self-references (e.g. DCDC channels providing the supply of LDOs).
The only sensible solution I found is registering the regulator devices
asynchronously, so that we do not have to unroll. Since this is a major
rework let's revert back to synchronous probing for now to fix the issue
at hand.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20230504173618.142075-14-sebastian.reichel@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
By overridering the device's of_node a bit earlier we can
get the GPIOs and any other DT properties from our own
device instead of relying on the parent device.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20230504173618.142075-13-sebastian.reichel@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
If the probe routine fails with -EPROBE_DEFER after taking over the
OF node from its parent driver, reprobing triggers pinctrl_bind_pins()
and that will fail. Fix this by setting of_node_reused, so that the
device does not try to setup pin muxing.
For me this always happens once the driver is marked to prefer async
probing and never happens without that flag.
Fixes: 259b93b21a ("regulator: Set PROBE_PREFER_ASYNCHRONOUS for drivers that existed in 4.14")
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20230504173618.142075-12-sebastian.reichel@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Expose and document the table lookup logic used by
regulator_set_ramp_delay_regmap, so that it can be
reused for devices that cannot be configured via
regulator_set_ramp_delay_regmap.
Tested-by: Diederik de Haas <didi.debian@cknow.org> # Rock64, Quartz64 Model A + B
Tested-by: Vincent Legoll <vincent.legoll@gmail.com> # Pine64 QuartzPro64
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20230504173618.142075-11-sebastian.reichel@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add hardware version read check for PMIC MT6359
Signed-off-by: Sen Chu <sen.chu@mediatek.com
Fixes: 4cfc965475 ("regulator: mt6359: Add support for MT6359P regulator")
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com
Link: https://lore.kernel.org/r/20230518040646.8730-1-sen.chu@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org
This patch fixes the error checking in core.c in debugfs_create_dir.
The correct way to check if an error occurred is 'IS_ERR' inline function.
Signed-off-by: Osama Muhammad <osmtendev@gmail.com
Suggested-by: Ivan Orlov <ivan.orlov0322@gmail.com
Link: https://lore.kernel.org/r/20230515172938.13338-1-osmtendev@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org
Split rk808 into a core and an i2c part in preparation for
SPI support.
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com> # for RTC
Tested-by: Diederik de Haas <didi.debian@cknow.org> # Rock64, Quartz64 Model A + B
Tested-by: Vincent Legoll <vincent.legoll@gmail.com> # Pine64 QuartzPro64
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20230504173618.142075-6-sebastian.reichel@collabora.com
Signed-off-by: Lee Jones <lee@kernel.org>
This fixes a copy & paste error.
No functional change intended, BUCK1_ENMODE_MASK equals BUCK2_ENMODE_MASK.
Fixes: 0935ff5f1f ("regulator: pca9450: add pca9450 pmic driver")
Originally-from: Robin Gong <yibin.gong@nxp.com
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de
Link: https://lore.kernel.org/r/20230512081935.2396180-1-alexander.stein@ew.tq-group.com
Signed-off-by: Mark Brown <broonie@kernel.org
Merge series from Mårten Lindahl <marten.lindahl@axis.com>:
This series adds basic support for TI's TPS62870/TPS62871/TPS62872/
TPS62873 high-frequency single-channel step-down converters with an
I2C interface.
The devices can operate in power save mode for maximum efficiency, or
forced-PWM mode for best transient performance and lowest output
voltage ripple. All chip variants have four output voltage ranges and
the driver changes active range depending on the requested voltage
setting.
There are differences in the electrical characteristics and packaging
between the variants, but the register interfaces are identical.
The driver's probe() first registers regulators in a loop and then in a
second loop passes them as irq data to the interrupt handlers. However
the function to get the regulator for given name
tps65219_get_rdev_by_name() was a no-op due to argument passed by value,
not pointer, thus the second loop assigned always same value - from
previous loop. The interrupts, when fired, where executed with wrong
data. Compiler also noticed it:
drivers/regulator/tps65219-regulator.c: In function ‘tps65219_get_rdev_by_name’:
drivers/regulator/tps65219-regulator.c:292:60: error: parameter ‘dev’ set but not used [-Werror=unused-but-set-parameter]
Fixes: c12ac5fc3e ("regulator: drivers: Add TI TPS65219 PMIC regulators support")
Cc: <stable@vger.kernel.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org
Reviewed-by: Markus Schneider-Pargmann <msp@baylibre.com
Link: https://lore.kernel.org/r/20230507144656.192800-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org
Add support for Texas Instruments TPS6287x, single-channel
synchronous step-down converters with four output voltage ranges.
Signed-off-by: Mårten Lindahl <marten.lindahl@axis.com
Link: https://lore.kernel.org/r/20230502-tps6287x-driver-v3-2-e25140a023f5@axis.com
Signed-off-by: Mark Brown <broonie@kernel.org
After commit b8a1a4cd5a ("i2c: Provide a temporary .probe_new()
call-back type"), all drivers being converted to .probe_new() and then
03c835f498 ("i2c: Switch .probe() to not take an id parameter") convert
back to (the new) .probe() to be able to eventually drop .probe_new() from
struct i2c_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de
Link: https://lore.kernel.org/r/20230505220218.1239542-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org
The summary of the changes for this pull requests is:
* Song Liu's new struct module_memory replacement
* Nick Alcock's MODULE_LICENSE() removal for non-modules
* My cleanups and enhancements to reduce the areas where we vmalloc
module memory for duplicates, and the respective debug code which
proves the remaining vmalloc pressure comes from userspace.
Most of the changes have been in linux-next for quite some time except
the minor fixes I made to check if a module was already loaded
prior to allocating the final module memory with vmalloc and the
respective debug code it introduces to help clarify the issue. Although
the functional change is small it is rather safe as it can only *help*
reduce vmalloc space for duplicates and is confirmed to fix a bootup
issue with over 400 CPUs with KASAN enabled. I don't expect stable
kernels to pick up that fix as the cleanups would have also had to have
been picked up. Folks on larger CPU systems with modules will want to
just upgrade if vmalloc space has been an issue on bootup.
Given the size of this request, here's some more elaborate details
on this pull request.
The functional change change in this pull request is the very first
patch from Song Liu which replaces the struct module_layout with a new
struct module memory. The old data structure tried to put together all
types of supported module memory types in one data structure, the new
one abstracts the differences in memory types in a module to allow each
one to provide their own set of details. This paves the way in the
future so we can deal with them in a cleaner way. If you look at changes
they also provide a nice cleanup of how we handle these different memory
areas in a module. This change has been in linux-next since before the
merge window opened for v6.3 so to provide more than a full kernel cycle
of testing. It's a good thing as quite a bit of fixes have been found
for it.
Jason Baron then made dynamic debug a first class citizen module user by
using module notifier callbacks to allocate / remove module specific
dynamic debug information.
Nick Alcock has done quite a bit of work cross-tree to remove module
license tags from things which cannot possibly be module at my request
so to:
a) help him with his longer term tooling goals which require a
deterministic evaluation if a piece a symbol code could ever be
part of a module or not. But quite recently it is has been made
clear that tooling is not the only one that would benefit.
Disambiguating symbols also helps efforts such as live patching,
kprobes and BPF, but for other reasons and R&D on this area
is active with no clear solution in sight.
b) help us inch closer to the now generally accepted long term goal
of automating all the MODULE_LICENSE() tags from SPDX license tags
In so far as a) is concerned, although module license tags are a no-op
for non-modules, tools which would want create a mapping of possible
modules can only rely on the module license tag after the commit
8b41fc4454 ("kbuild: create modules.builtin without Makefile.modbuiltin
or tristate.conf"). Nick has been working on this *for years* and
AFAICT I was the only one to suggest two alternatives to this approach
for tooling. The complexity in one of my suggested approaches lies in
that we'd need a possible-obj-m and a could-be-module which would check
if the object being built is part of any kconfig build which could ever
lead to it being part of a module, and if so define a new define
-DPOSSIBLE_MODULE [0]. A more obvious yet theoretical approach I've
suggested would be to have a tristate in kconfig imply the same new
-DPOSSIBLE_MODULE as well but that means getting kconfig symbol names
mapping to modules always, and I don't think that's the case today. I am
not aware of Nick or anyone exploring either of these options. Quite
recently Josh Poimboeuf has pointed out that live patching, kprobes and
BPF would benefit from resolving some part of the disambiguation as
well but for other reasons. The function granularity KASLR (fgkaslr)
patches were mentioned but Joe Lawrence has clarified this effort has
been dropped with no clear solution in sight [1].
In the meantime removing module license tags from code which could never
be modules is welcomed for both objectives mentioned above. Some
developers have also welcomed these changes as it has helped clarify
when a module was never possible and they forgot to clean this up,
and so you'll see quite a bit of Nick's patches in other pull
requests for this merge window. I just picked up the stragglers after
rc3. LWN has good coverage on the motivation behind this work [2] and
the typical cross-tree issues he ran into along the way. The only
concrete blocker issue he ran into was that we should not remove the
MODULE_LICENSE() tags from files which have no SPDX tags yet, even if
they can never be modules. Nick ended up giving up on his efforts due
to having to do this vetting and backlash he ran into from folks who
really did *not understand* the core of the issue nor were providing
any alternative / guidance. I've gone through his changes and dropped
the patches which dropped the module license tags where an SPDX
license tag was missing, it only consisted of 11 drivers. To see
if a pull request deals with a file which lacks SPDX tags you
can just use:
./scripts/spdxcheck.py -f \
$(git diff --name-only commid-id | xargs echo)
You'll see a core module file in this pull request for the above,
but that's not related to his changes. WE just need to add the SPDX
license tag for the kernel/module/kmod.c file in the future but
it demonstrates the effectiveness of the script.
Most of Nick's changes were spread out through different trees,
and I just picked up the slack after rc3 for the last kernel was out.
Those changes have been in linux-next for over two weeks.
The cleanups, debug code I added and final fix I added for modules
were motivated by David Hildenbrand's report of boot failing on
a systems with over 400 CPUs when KASAN was enabled due to running
out of virtual memory space. Although the functional change only
consists of 3 lines in the patch "module: avoid allocation if module is
already present and ready", proving that this was the best we can
do on the modules side took quite a bit of effort and new debug code.
The initial cleanups I did on the modules side of things has been
in linux-next since around rc3 of the last kernel, the actual final
fix for and debug code however have only been in linux-next for about a
week or so but I think it is worth getting that code in for this merge
window as it does help fix / prove / evaluate the issues reported
with larger number of CPUs. Userspace is not yet fixed as it is taking
a bit of time for folks to understand the crux of the issue and find a
proper resolution. Worst come to worst, I have a kludge-of-concept [3]
of how to make kernel_read*() calls for modules unique / converge them,
but I'm currently inclined to just see if userspace can fix this
instead.
[0] https://lore.kernel.org/all/Y/kXDqW+7d71C4wz@bombadil.infradead.org/
[1] https://lkml.kernel.org/r/025f2151-ce7c-5630-9b90-98742c97ac65@redhat.com
[2] https://lwn.net/Articles/927569/
[3] https://lkml.kernel.org/r/20230414052840.1994456-3-mcgrof@kernel.org
-----BEGIN PGP SIGNATURE-----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=56WK
-----END PGP SIGNATURE-----
Merge tag 'modules-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/mcgrof/linux
Pull module updates from Luis Chamberlain:
"The summary of the changes for this pull requests is:
- Song Liu's new struct module_memory replacement
- Nick Alcock's MODULE_LICENSE() removal for non-modules
- My cleanups and enhancements to reduce the areas where we vmalloc
module memory for duplicates, and the respective debug code which
proves the remaining vmalloc pressure comes from userspace.
Most of the changes have been in linux-next for quite some time except
the minor fixes I made to check if a module was already loaded prior
to allocating the final module memory with vmalloc and the respective
debug code it introduces to help clarify the issue. Although the
functional change is small it is rather safe as it can only *help*
reduce vmalloc space for duplicates and is confirmed to fix a bootup
issue with over 400 CPUs with KASAN enabled. I don't expect stable
kernels to pick up that fix as the cleanups would have also had to
have been picked up. Folks on larger CPU systems with modules will
want to just upgrade if vmalloc space has been an issue on bootup.
Given the size of this request, here's some more elaborate details:
The functional change change in this pull request is the very first
patch from Song Liu which replaces the 'struct module_layout' with a
new 'struct module_memory'. The old data structure tried to put
together all types of supported module memory types in one data
structure, the new one abstracts the differences in memory types in a
module to allow each one to provide their own set of details. This
paves the way in the future so we can deal with them in a cleaner way.
If you look at changes they also provide a nice cleanup of how we
handle these different memory areas in a module. This change has been
in linux-next since before the merge window opened for v6.3 so to
provide more than a full kernel cycle of testing. It's a good thing as
quite a bit of fixes have been found for it.
Jason Baron then made dynamic debug a first class citizen module user
by using module notifier callbacks to allocate / remove module
specific dynamic debug information.
Nick Alcock has done quite a bit of work cross-tree to remove module
license tags from things which cannot possibly be module at my request
so to:
a) help him with his longer term tooling goals which require a
deterministic evaluation if a piece a symbol code could ever be
part of a module or not. But quite recently it is has been made
clear that tooling is not the only one that would benefit.
Disambiguating symbols also helps efforts such as live patching,
kprobes and BPF, but for other reasons and R&D on this area is
active with no clear solution in sight.
b) help us inch closer to the now generally accepted long term goal
of automating all the MODULE_LICENSE() tags from SPDX license tags
In so far as a) is concerned, although module license tags are a no-op
for non-modules, tools which would want create a mapping of possible
modules can only rely on the module license tag after the commit
8b41fc4454 ("kbuild: create modules.builtin without
Makefile.modbuiltin or tristate.conf").
Nick has been working on this *for years* and AFAICT I was the only
one to suggest two alternatives to this approach for tooling. The
complexity in one of my suggested approaches lies in that we'd need a
possible-obj-m and a could-be-module which would check if the object
being built is part of any kconfig build which could ever lead to it
being part of a module, and if so define a new define
-DPOSSIBLE_MODULE [0].
A more obvious yet theoretical approach I've suggested would be to
have a tristate in kconfig imply the same new -DPOSSIBLE_MODULE as
well but that means getting kconfig symbol names mapping to modules
always, and I don't think that's the case today. I am not aware of
Nick or anyone exploring either of these options. Quite recently Josh
Poimboeuf has pointed out that live patching, kprobes and BPF would
benefit from resolving some part of the disambiguation as well but for
other reasons. The function granularity KASLR (fgkaslr) patches were
mentioned but Joe Lawrence has clarified this effort has been dropped
with no clear solution in sight [1].
In the meantime removing module license tags from code which could
never be modules is welcomed for both objectives mentioned above. Some
developers have also welcomed these changes as it has helped clarify
when a module was never possible and they forgot to clean this up, and
so you'll see quite a bit of Nick's patches in other pull requests for
this merge window. I just picked up the stragglers after rc3. LWN has
good coverage on the motivation behind this work [2] and the typical
cross-tree issues he ran into along the way. The only concrete blocker
issue he ran into was that we should not remove the MODULE_LICENSE()
tags from files which have no SPDX tags yet, even if they can never be
modules. Nick ended up giving up on his efforts due to having to do
this vetting and backlash he ran into from folks who really did *not
understand* the core of the issue nor were providing any alternative /
guidance. I've gone through his changes and dropped the patches which
dropped the module license tags where an SPDX license tag was missing,
it only consisted of 11 drivers. To see if a pull request deals with a
file which lacks SPDX tags you can just use:
./scripts/spdxcheck.py -f \
$(git diff --name-only commid-id | xargs echo)
You'll see a core module file in this pull request for the above, but
that's not related to his changes. WE just need to add the SPDX
license tag for the kernel/module/kmod.c file in the future but it
demonstrates the effectiveness of the script.
Most of Nick's changes were spread out through different trees, and I
just picked up the slack after rc3 for the last kernel was out. Those
changes have been in linux-next for over two weeks.
The cleanups, debug code I added and final fix I added for modules
were motivated by David Hildenbrand's report of boot failing on a
systems with over 400 CPUs when KASAN was enabled due to running out
of virtual memory space. Although the functional change only consists
of 3 lines in the patch "module: avoid allocation if module is already
present and ready", proving that this was the best we can do on the
modules side took quite a bit of effort and new debug code.
The initial cleanups I did on the modules side of things has been in
linux-next since around rc3 of the last kernel, the actual final fix
for and debug code however have only been in linux-next for about a
week or so but I think it is worth getting that code in for this merge
window as it does help fix / prove / evaluate the issues reported with
larger number of CPUs. Userspace is not yet fixed as it is taking a
bit of time for folks to understand the crux of the issue and find a
proper resolution. Worst come to worst, I have a kludge-of-concept [3]
of how to make kernel_read*() calls for modules unique / converge
them, but I'm currently inclined to just see if userspace can fix this
instead"
Link: https://lore.kernel.org/all/Y/kXDqW+7d71C4wz@bombadil.infradead.org/ [0]
Link: https://lkml.kernel.org/r/025f2151-ce7c-5630-9b90-98742c97ac65@redhat.com [1]
Link: https://lwn.net/Articles/927569/ [2]
Link: https://lkml.kernel.org/r/20230414052840.1994456-3-mcgrof@kernel.org [3]
* tag 'modules-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/mcgrof/linux: (121 commits)
module: add debugging auto-load duplicate module support
module: stats: fix invalid_mod_bytes typo
module: remove use of uninitialized variable len
module: fix building stats for 32-bit targets
module: stats: include uapi/linux/module.h
module: avoid allocation if module is already present and ready
module: add debug stats to help identify memory pressure
module: extract patient module check into helper
modules/kmod: replace implementation with a semaphore
Change DEFINE_SEMAPHORE() to take a number argument
module: fix kmemleak annotations for non init ELF sections
module: Ignore L0 and rename is_arm_mapping_symbol()
module: Move is_arm_mapping_symbol() to module_symbol.h
module: Sync code of is_arm_mapping_symbol()
scripts/gdb: use mem instead of core_layout to get the module address
interconnect: remove module-related code
interconnect: remove MODULE_LICENSE in non-modules
zswap: remove MODULE_LICENSE in non-modules
zpool: remove MODULE_LICENSE in non-modules
x86/mm/dump_pagetables: remove MODULE_LICENSE in non-modules
...
- Add a thermal zone 'devdata' accessor and modify several drivers to
use it (Daniel Lezcano).
- Prevent drivers from using the 'device' internal thermal zone
structure field directly (Daniel Lezcano).
- Clean up the hwmon thermal driver (Daniel Lezcano).
- Add thermal zone id accessor and thermal zone type accessor
and prevent drivers from using thermal zone fields directly (Daniel
Lezcano).
- Clean up the acerhdf and tegra thermal drivers (Daniel Lezcano).
- Add lower bound check for sysfs input to the x86_pkg_temp_thermal
Intel thermal driver (Zhang Rui).
- Add more thermal zone device encapsulation: prevent setting structure
field directly, access the sensor device instead the thermal zone's
device for trace, relocate the traces in drivers/thermal (Daniel
Lezcano).
- Use the generic trip point for the i.MX and remove the get_trip_temp
ops (Daniel Lezcano).
- Use the devm_platform_ioremap_resource() in the Hisilicon driver
(Yang Li).
- Remove R-Car H3 ES1.* handling as public has only access to the ES2
version and the upstream support for the ES1 has been shutdown (Wolfram
Sang).
- Add a delay after initializing the bank in order to let the time to
the hardware to initialze itself before reading the temperature
(Amjad Ouled-Ameur).
- Add MT8365 support (Amjad Ouled-Ameur).
- Preparational cleanup and DT bindings for RK3588 support (Sebastian
Reichel).
- Add driver support for RK3588 (Finley Xiao).
- Use devm_reset_control_array_get_exclusive() for the Rockchip driver
(Ye Xingchen).
- Detect power gated thermal zones and return -EAGAIN when reading the
temperature (Mikko Perttunen).
- Remove thermal_bind_params structure as it is unused (Zhang Rui)
- Drop unneeded quotes in DT bindings allowing to run yamllint (Rob
Herring).
- Update the power allocator documentation according to the thermal
trace relocation (Lukas Bulwahn).
- Fix sensor 1 interrupt status bitmask for the Mediatek LVTS sensor
(Chen-Yu Tsai).
- Use the dev_err_probe() helper in the Amlogic driver (Ye Xingchen).
- Add AP domain support to LVTS thermal controllers for mt8195
(Balsam CHIHI).
- Remove buggy call to thermal_of_zone_unregister() (Daniel Lezcano).
- Make thermal_of_zone_[un]register() private to the thermal OF code
(Daniel Lezcano).
- Create a private copy of the thermal zone device parameters
structure when registering a thermal zone (Daniel Lezcano).
- Fix a kernel NULL pointer dereference in thermal_hwmon (Zhang Rui).
- Revert recent message adjustment in thermal_hwmon (Rafael Wysocki).
- Use of_property_present() for testing DT property presence in
thermal control code (Rob Herring).
- Clean up thermal_list_lock locking in the thermal core (Rafael
Wysocki).
- Add DLVR support for RFIM control in the int340x Intel thermal
driver (Srinivas Pandruvada).
-----BEGIN PGP SIGNATURE-----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=XNJE
-----END PGP SIGNATURE-----
Merge tag 'thermal-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull thermal control updates from Rafael Wysocki:
"These mostly continue to prepare the thermal control subsystem for
using unified representation of trip points, which includes cleanups,
code refactoring and similar and update several drivers (for other
reasons), which includes new hardware support.
Specifics:
- Add a thermal zone 'devdata' accessor and modify several drivers to
use it (Daniel Lezcano)
- Prevent drivers from using the 'device' internal thermal zone
structure field directly (Daniel Lezcano)
- Clean up the hwmon thermal driver (Daniel Lezcano)
- Add thermal zone id accessor and thermal zone type accessor and
prevent drivers from using thermal zone fields directly (Daniel
Lezcano)
- Clean up the acerhdf and tegra thermal drivers (Daniel Lezcano)
- Add lower bound check for sysfs input to the x86_pkg_temp_thermal
Intel thermal driver (Zhang Rui)
- Add more thermal zone device encapsulation: prevent setting
structure field directly, access the sensor device instead the
thermal zone's device for trace, relocate the traces in
drivers/thermal (Daniel Lezcano)
- Use the generic trip point for the i.MX and remove the
get_trip_temp ops (Daniel Lezcano)
- Use the devm_platform_ioremap_resource() in the Hisilicon driver
(Yang Li)
- Remove R-Car H3 ES1.* handling as public has only access to the ES2
version and the upstream support for the ES1 has been shutdown
(Wolfram Sang)
- Add a delay after initializing the bank in order to let the time to
the hardware to initialze itself before reading the temperature
(Amjad Ouled-Ameur)
- Add MT8365 support (Amjad Ouled-Ameur)
- Preparational cleanup and DT bindings for RK3588 support (Sebastian
Reichel)
- Add driver support for RK3588 (Finley Xiao)
- Use devm_reset_control_array_get_exclusive() for the Rockchip
driver (Ye Xingchen)
- Detect power gated thermal zones and return -EAGAIN when reading
the temperature (Mikko Perttunen)
- Remove thermal_bind_params structure as it is unused (Zhang Rui)
- Drop unneeded quotes in DT bindings allowing to run yamllint (Rob
Herring)
- Update the power allocator documentation according to the thermal
trace relocation (Lukas Bulwahn)
- Fix sensor 1 interrupt status bitmask for the Mediatek LVTS sensor
(Chen-Yu Tsai)
- Use the dev_err_probe() helper in the Amlogic driver (Ye Xingchen)
- Add AP domain support to LVTS thermal controllers for mt8195
(Balsam CHIHI)
- Remove buggy call to thermal_of_zone_unregister() (Daniel Lezcano)
- Make thermal_of_zone_[un]register() private to the thermal OF code
(Daniel Lezcano)
- Create a private copy of the thermal zone device parameters
structure when registering a thermal zone (Daniel Lezcano)
- Fix a kernel NULL pointer dereference in thermal_hwmon (Zhang Rui)
- Revert recent message adjustment in thermal_hwmon (Rafael Wysocki)
- Use of_property_present() for testing DT property presence in
thermal control code (Rob Herring)
- Clean up thermal_list_lock locking in the thermal core (Rafael
Wysocki)
- Add DLVR support for RFIM control in the int340x Intel thermal
driver (Srinivas Pandruvada)"
* tag 'thermal-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (55 commits)
thermal: intel: int340x: Add DLVR support for RFIM control
thermal/core: Alloc-copy-free the thermal zone parameters structure
thermal/of: Unexport unused OF functions
thermal/drivers/bcm2835: Remove buggy call to thermal_of_zone_unregister
thermal/drivers/mediatek/lvts_thermal: Add AP domain for mt8195
dt-bindings: thermal: mediatek: Add AP domain to LVTS thermal controllers for mt8195
thermal: amlogic: Use dev_err_probe()
thermal/drivers/mediatek/lvts_thermal: Fix sensor 1 interrupt status bitmask
MAINTAINERS: adjust entry in THERMAL/POWER_ALLOCATOR after header movement
dt-bindings: thermal: Drop unneeded quotes
thermal/core: Remove thermal_bind_params structure
thermal/drivers/tegra-bpmp: Handle offline zones
thermal/drivers/rockchip: use devm_reset_control_array_get_exclusive()
dt-bindings: rockchip-thermal: Support the RK3588 SoC compatible
thermal/drivers/rockchip: Support RK3588 SoC in the thermal driver
thermal/drivers/rockchip: Support dynamic sized sensor array
thermal/drivers/rockchip: Simplify channel id logic
thermal/drivers/rockchip: Use dev_err_probe
thermal/drivers/rockchip: Simplify clock logic
thermal/drivers/rockchip: Simplify getting match data
...
A fairly quiet release, there were some cleanup and a couple of new
devices but the biggest change was converting most of the drivers to use
asynchronous probe. This allows us to ramp up multiple regulators in
parallel during boot which can have a noticable impact on modern
systems.
- Update of drivers to PROBE_PREFER_ASYNCHRONOUS to mitigate issues
with ramp times slowing down boots.
- Convert to void remove callbacks.
- Support for voltage monitoring on DA9063
- Support for Qualcomm PMC8180 and PMM8654au, Richtek RT4803 and
RT5739, Rockchip RK860x,
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmRGfzcACgkQJNaLcl1U
h9B5oAgAgNkRTmrHDzuyFZD0JUt6Wy0jewxNH7Ie5ucYEPNPaWGfPDvJkpjDZ/iB
UTPrhFAvNfVX2Z2E3Pdx4jhvbq3chlavpDaMWEqnimdfIqqqHLPEiRtVG2DiXAub
2AKS8piy136EDtWf4/HCoKiLf5Osr4i6bpOUoaHoNIqTtjhu2p7FXC9rjuRsmQgC
8kiA/fsLRcdzyhQb86myl4QktYiWTCrHzP7jpKlHAHRf5OBozapGgPR2Ih/cNoTR
0lbdvst1arkUr1wMGqvYAg1UjlAmA9TA/1kkm6j98G6ruuUzeay9bGN9tCk4SMjf
kAXks6ohTS9VvqN5ykrjm/2WF/Y9yA==
=AJNv
-----END PGP SIGNATURE-----
Merge tag 'regulator-v6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"A fairly quiet release, there were some cleanup and a couple of new
devices but the biggest change was converting most of the drivers to
use asynchronous probe. This allows us to ramp up multiple regulators
in parallel during boot which can have a noticable impact on modern
systems.
Summary:
- Update of drivers to PROBE_PREFER_ASYNCHRONOUS to mitigate issues
with ramp times slowing down boots.
- Convert to void remove callbacks.
- Support for voltage monitoring on DA9063
- Support for Qualcomm PMC8180 and PMM8654au, Richtek RT4803 and
RT5739, Rockchip RK860x"
* tag 'regulator-v6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (46 commits)
regulator: dt-bindings: qcom,rpmh: Combine PM6150L and PM8150L if-then
regulator: core: Make regulator_lock_two() logic easier to follow
regulator: dt-bindings: qcom,rpmh: Correct PM8550 family supplies
regulator: stm32-pwr: fix of_iomap leak
dt-bindings: mfd: dlg,da9063: document voltage monitoring
regulator: da9063: implement setter for voltage monitoring
regulator: da9063: add voltage monitoring registers
regulator: fan53555: Add support for RK860X
regulator: fan53555: Use dev_err_probe
regulator: fan53555: Improve vsel_mask computation
regulator: fan53555: Make use of the bit macros
regulator: fan53555: Remove unused *_SLEW_SHIFT definitions
regulator: dt-bindings: fcs,fan53555: Add support for RK860X
regulator: qcom_smd: Add MP5496 S1 regulator
regulator: qcom_smd: Add s1 sub-node to mp5496 regulator
regulator: qcom,rpmh: add compatible for pmm8654au RPMH
regulator: qcom-rpmh: add support for pmm8654au regulators
regulator: core: Avoid lockdep reports when resolving supplies
regulator: core: Consistently set mutex_owner when using ww_mutex_lock_slow()
regulator: dt-bindings: qcom,rpmh: Add compatible for PMC8180
...
Since commit 8b41fc4454 ("kbuild: create modules.builtin without
Makefile.modbuiltin or tristate.conf"), MODULE_LICENSE declarations
are used to identify modules. As a consequence, uses of the macro
in non-modules will cause modprobe to misidentify their containing
object file as a module when it is not (false positives), and modprobe
might succeed rather than failing with a suitable error message.
So remove it in the files in this commit, none of which can be built as
modules.
Signed-off-by: Nick Alcock <nick.alcock@oracle.com>
Suggested-by: Luis Chamberlain <mcgrof@kernel.org>
Cc: Luis Chamberlain <mcgrof@kernel.org>
Cc: linux-modules@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: Hitomi Hasegawa <hasegawa-hitomi@fujitsu.com>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
Merge series from Benjamin Bara <bbara93@gmail.com>:
Follow-up for my initial patch regarding the disabling of unused
voltage monitors. We use the PWR_OK functionality, which asserts GP_FB2
if every monitored voltage is in range. This patch should provide the
possibility to deactivate a voltage monitor from the DT if the regulator
might be disabled during run time. For this purpose, the regulator
notification support is used:
https://lore.kernel.org/all/cover.1622628333.git.matti.vaittinen@fi.rohmeurope.com/
Smatch reports:
drivers/regulator/stm32-pwr.c:166 stm32_pwr_regulator_probe() warn:
'base' from of_iomap() not released on lines: 151,166.
In stm32_pwr_regulator_probe(), base is not released
when devm_kzalloc() fails to allocate memory or
devm_regulator_register() fails to register a new regulator device,
which may cause a leak.
To fix this issue, replace of_iomap() with
devm_platform_ioremap_resource(). devm_platform_ioremap_resource()
is a specialized function for platform devices.
It allows 'base' to be automatically released whether the probe
function succeeds or fails.
Besides, use IS_ERR(base) instead of !base
as the return value of devm_platform_ioremap_resource()
can either be a pointer to the remapped memory or
an ERR_PTR() encoded error code if the operation fails.
Fixes: dc62f951a6 ("regulator: stm32-pwr: Fix return value check in stm32_pwr_regulator_probe()")
Signed-off-by: YAN SHI <m202071378@hust.edu.cn>
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/oe-kbuild-all/202304111750.o2643eJN-lkp@intel.com/
Reviewed-by: Dongliang Mu <dzm91@hust.edu.cn>
Link: https://lore.kernel.org/r/20230412033529.18890-1-m202071378@hust.edu.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
Allow to en- and disable voltage monitoring from the device tree.
Consider that the da9063 only monitors under- *and* over-voltage
together, so both must be set to the same severity and value.
Reviewed-by: Adam Ward <DLG-Adam.Ward.opensource@dm.renesas.com>
Signed-off-by: Benjamin Bara <benjamin.bara@skidata.com>
Link: https://lore.kernel.org/r/20230403-da9063-disable-unused-v3-2-cc4dc698864c@skidata.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the definitions for the registers responsible for voltage
monitoring. Add a voltage monitor enable bitfield per regulator.
Reviewed-by: Matti Vaittinen <mazziesaccount@gmail.com>
Reviewed-by: Adam Ward <DLG-Adam.Ward.opensource@dm.renesas.com>
Signed-off-by: Benjamin Bara <benjamin.bara@skidata.com>
Link: https://lore.kernel.org/r/20230403-da9063-disable-unused-v3-1-cc4dc698864c@skidata.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Cristian Ciocaltea <cristian.ciocaltea@collabora.com>:
This patch series introduces support for the Rockchip RK860X regulators,
while also providing a few fixes and improvements to the existing fan53555
driver.
RK8600/RK8601 are quite similar to the FAN53555 regulators.
RK8602/RK8603 are a bit different, having a wider output voltage
selection range, from 0.5 V to 1.5 V in 6.25 mV steps. They are used
in the Rock 5B board to power the ARM Cortex-A76 cores and the NPU.
Extend the existing fan53555 driver to support the Rockchip RK860X
regulators.
RK8600/RK8601 are pretty similar to the FAN53555 regulators.
RK8602/RK8603 are a bit different, having a wider output voltage
selection range, from 0.5 V to 1.5 V in 6.25 mV steps. They also use
additional VSEL0/VSEL1 registers for the voltage selector, but the
enable and mode bits are still located in the original FAN53555 specific
VSEL0/VSEL1 registers.
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230406194158.963352-9-cristian.ciocaltea@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use dev_err_probe() instead of dev_err() in the probe function, which
ensures the error code is always printed and, additionally, simplifies
the code a bit.
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Link: https://lore.kernel.org/r/20230406194158.963352-8-cristian.ciocaltea@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In preparation for introducing support for additional regulators which
do not use the maximum number of voltage selectors available for a given
mask, improve the mask computation formula by using fls().
Note fls() requires the bitops header, hence include it explicitly and
drop bits.h which is already pulled by bitops.h.
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Link: https://lore.kernel.org/r/20230406194158.963352-7-cristian.ciocaltea@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
For consistency and improved clarity, use BIT() and GENMASK() macros for
defining the bitfields inside the registers. No functional changes
intended.
While here, also fix DIE_{ID,REV} inconsistent indentation.
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Link: https://lore.kernel.org/r/20230406194158.963352-6-cristian.ciocaltea@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit b61ac767db ("regulator: fan53555: Convert to use
regulator_set_ramp_delay_regmap") removed the slew_shift member from
struct fan53555_device_info, hence the {CTL,TCS}_SLEW_SHIFT definitions
remained unused. Drop them.
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Link: https://lore.kernel.org/r/20230406194158.963352-5-cristian.ciocaltea@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Adding support for MP5496 S1 regulator on IPQ9574 SoC.
Co-developed-by: Praveenkumar I <quic_ipkumar@quicinc.com>
Signed-off-by: Praveenkumar I <quic_ipkumar@quicinc.com>
Signed-off-by: Devi Priya <quic_devipriy@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230407155727.20615-3-quic_devipriy@quicinc.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The support for TCS4525 regulator has been introduced with a wrong
ramp-rate mask, which has been defined as a logical expression instead
of a bit shift operation.
For clarity, fix it using GENMASK() macro.
Fixes: 914df8faa7 ("regulator: fan53555: Add TCS4525 DCDC support")
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Link: https://lore.kernel.org/r/20230406171806.948290-4-cristian.ciocaltea@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Since commit f2a9eb975a ("regulator: fan53555: Add support for
FAN53526") the driver makes use of the BIT() macro, but relies on the
bits header being implicitly included.
Explicitly pull the header in to avoid potential build failures in some
configurations.
While here, reorder include directives alphabetically.
Fixes: f2a9eb975a ("regulator: fan53555: Add support for FAN53526")
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Link: https://lore.kernel.org/r/20230406171806.948290-3-cristian.ciocaltea@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the RPMH regulators exposed by the PMM8654au PMIC and its variants.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230406192811.460888-3-brgl@bgdev.pl
Signed-off-by: Mark Brown <broonie@kernel.org>
An automated bot told me that there was a potential lockdep problem
with regulators. This was on the chromeos-5.15 kernel, but I see
nothing that would be different downstream compared to upstream. The
bot said:
============================================
WARNING: possible recursive locking detected
5.15.104-lockdep-17461-gc1e499ed6604 #1 Not tainted
--------------------------------------------
kworker/u16:4/115 is trying to acquire lock:
ffffff8083110170 (regulator_ww_class_mutex){+.+.}-{3:3}, at: create_regulator+0x398/0x7ec
but task is already holding lock:
ffffff808378e170 (regulator_ww_class_mutex){+.+.}-{3:3}, at: ww_mutex_trylock+0x3c/0x7b8
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(regulator_ww_class_mutex);
lock(regulator_ww_class_mutex);
*** DEADLOCK ***
May be due to missing lock nesting notation
4 locks held by kworker/u16:4/115:
#0: ffffff808006a948 ((wq_completion)events_unbound){+.+.}-{0:0}, at: process_one_work+0x520/0x1348
#1: ffffffc00e0a7cc0 ((work_completion)(&entry->work)){+.+.}-{0:0}, at: process_one_work+0x55c/0x1348
#2: ffffff80828a2260 (&dev->mutex){....}-{3:3}, at: __device_attach_async_helper+0xd0/0x2a4
#3: ffffff808378e170 (regulator_ww_class_mutex){+.+.}-{3:3}, at: ww_mutex_trylock+0x3c/0x7b8
stack backtrace:
CPU: 2 PID: 115 Comm: kworker/u16:4 Not tainted 5.15.104-lockdep-17461-gc1e499ed6604 #1 9292e52fa83c0e23762b2b3aa1bacf5787a4d5da
Hardware name: Google Quackingstick (rev0+) (DT)
Workqueue: events_unbound async_run_entry_fn
Call trace:
dump_backtrace+0x0/0x4ec
show_stack+0x34/0x50
dump_stack_lvl+0xdc/0x11c
dump_stack+0x1c/0x48
__lock_acquire+0x16d4/0x6c74
lock_acquire+0x208/0x750
__mutex_lock_common+0x11c/0x11f8
ww_mutex_lock+0xc0/0x440
create_regulator+0x398/0x7ec
regulator_resolve_supply+0x654/0x7c4
regulator_register_resolve_supply+0x30/0x120
class_for_each_device+0x1b8/0x230
regulator_register+0x17a4/0x1f40
devm_regulator_register+0x60/0xd0
reg_fixed_voltage_probe+0x728/0xaec
platform_probe+0x150/0x1c8
really_probe+0x274/0xa20
__driver_probe_device+0x1dc/0x3f4
driver_probe_device+0x78/0x1c0
__device_attach_driver+0x1ac/0x2c8
bus_for_each_drv+0x11c/0x190
__device_attach_async_helper+0x1e4/0x2a4
async_run_entry_fn+0xa0/0x3ac
process_one_work+0x638/0x1348
worker_thread+0x4a8/0x9c4
kthread+0x2e4/0x3a0
ret_from_fork+0x10/0x20
The problem was first reported soon after we made many of the
regulators probe asynchronously, though nothing I've seen implies that
the problems couldn't have also happened even without that.
I haven't personally been able to reproduce the lockdep issue, but the
issue does look somewhat legitimate. Specifically, it looks like in
regulator_resolve_supply() we are holding a "rdev" lock while calling
set_supply() -> create_regulator() which grabs the lock of a
_different_ "rdev" (the one for our supply). This is not necessarily
safe from a lockdep perspective since there is no documented ordering
between these two locks.
In reality, we should always be locking a regulator before the
supplying regulator, so I don't expect there to be any real deadlocks
in practice. However, the regulator framework in general doesn't
express this to lockdep.
Let's fix the issue by simply grabbing the two locks involved in the
same way we grab multiple locks elsewhere in the regulator framework:
using the "wound/wait" mechanisms.
Fixes: eaa7995c52 ("regulator: core: avoid regulator_resolve_supply() race condition")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20230329143317.RFC.v2.2.I30d8e1ca10cfbe5403884cdd192253a2e063eb9e@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
When a codepath locks a rdev using ww_mutex_lock_slow() directly then
that codepath is responsible for incrementing the "ref_cnt" and also
setting the "mutex_owner" to "current".
The regulator core consistently got that right for "ref_cnt" but
didn't always get it right for "mutex_owner". Let's fix this.
It's unlikely that this truly matters because the "mutex_owner" is
only needed if we're going to do subsequent locking of the same
rdev. However, even though it's not truly needed it seems less
surprising if we consistently set "mutex_owner" properly.
Fixes: f8702f9e4a ("regulator: core: Use ww_mutex for regulators locking")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20230329143317.RFC.v2.1.I4e9d433ea26360c06dd1381d091c82bb1a4ce843@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
RT4803 is a boost converter that integrates an internal bypass FET. It
will automatically transform the operation mode between bypass and boost
based on the voltage difference of the input and output voltage.
Signed-off-by: ChiYuan Huang <cy_huang@richtek.com>
Link: https://lore.kernel.org/r/1680050606-461-2-git-send-email-cy_huang@richtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
devm_clk_get() can return -EPROBE_DEFER. So it is better to return the
error code from devm_clk_get(), instead of a hard coded -ENOENT.
This gives more opportunities to successfully probe the driver.
Fixes: 8959e53244 ("regulator: fixed: add possibility to enable by clock")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/18459fae3d017a66313699c7c8456b28158b2dd0.1679819354.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Mark Brown <broonie@kernel.org>
This reverts commit 58973046c1 ("regulator: qcom-rpmh: Use
PROBE_FORCE_SYNCHRONOUS"). Further digging into the problems that
prompted the us to switch to synchronous probe showed that the root
cause was a missing "rootwait" in the kernel command line
arguments. Let's reinstate asynchronous probe.
Fixes: 58973046c1 ("regulator: qcom-rpmh: Use PROBE_FORCE_SYNCHRONOUS")
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20230324063357.1.Ifdf3625a3c5c9467bd87bfcdf726c884ad220a35@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
Restore synchronous probing for 'qcom,pm8150-rpmh-regulators' because
otherwise the UFSHC device is not properly initialized on QRB5165-RB5
board.
Fixes: ed6962cc3e ("regulator: Set PROBE_PREFER_ASYNCHRONOUS for drivers between 4.14 and 4.19")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20230323220518.3247530-1-m.szyprowski@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Restore synchronous probing for Arizona regulators as the main MFD
relies on the ordering of the devices probing.
As these regulators are built into the CODEC and typically have no DT
representation the regulator framework is unaware of their existence
until the driver probes. These means the probing of the driver needs to
be synchronous to ensure the regulators are not substitued for the dummy
later when the users request them.
Fixes: 259b93b21a ("regulator: Set PROBE_PREFER_ASYNCHRONOUS for drivers that existed in 4.14")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230323132047.833737-2-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Restore synchronous probing for Arizona regulators because otherwise
the main MFD driver will not find its core supplies.
As these regulators are built into the CODEC and typically have no DT
representation the regulator framework is unaware of their existence
until the driver probes. These means the probing of the driver needs to
be synchronous to ensure the regulators are not substitued for the dummy
later when the users request them.
Fixes: 259b93b21a ("regulator: Set PROBE_PREFER_ASYNCHRONOUS for drivers that existed in 4.14")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230323132047.833737-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Restore synchronous probing for wm8994 regulators because otherwise the
sound device is never initialized on Exynos5250-based Arndale board.
Fixes: 259b93b21a ("regulator: Set PROBE_PREFER_ASYNCHRONOUS for drivers that existed in 4.14")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230323083312.199189-1-m.szyprowski@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This follows on the change ("regulator: Set PROBE_PREFER_ASYNCHRONOUS
for drivers that existed in 4.14") but changes regulators didn't exist
in Linux 5.15 but did exist in Linux 6.1.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20230316125351.6.Ibc8a86ddd5055ebbbe487a529199db7b36ccad1a@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
This follows on the change ("regulator: Set PROBE_PREFER_ASYNCHRONOUS
for drivers that existed in 4.14") but changes regulators didn't exist
in Linux 5.10 but did exist in Linux 5.15.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20230316125351.5.Ia0e6d859bdfe42ea5c187fb1eb4705c1b5ea23a1@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
This follows on the change ("regulator: Set PROBE_PREFER_ASYNCHRONOUS
for drivers that existed in 4.14") but changes regulators didn't exist
in Linux 5.4 but did exist in Linux 5.10.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20230316125351.4.I01f21c98901641a009890590ddc1354c0f294e5e@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
This follows on the change ("regulator: Set PROBE_PREFER_ASYNCHRONOUS
for drivers that existed in 4.14") but changes regulators didn't exist
in Linux 4.19 but did exist in Linux 5.4.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20230316125351.3.I45bf925ca9537da5f647e2acb0ad207c0c98af81@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
This follows on the change ("regulator: Set PROBE_PREFER_ASYNCHRONOUS
for drivers that existed in 4.14") but changes regulators didn't exist
in Linux 4.14 but did exist in Linux 4.19.
NOTE: from a quick "git cherry-pick" it looks as if
"bd718x7-regulator.c" didn't actually exist in v4.19. In 4.19 it was
named "bd71837-regulator.c". See commit 2ece646c90 ("regulator:
bd718xx: rename bd71837 to 718xx")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20230316125351.2.Iad1f25517bb46a6c7fca8d8c80ed4fc258a79ed9@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
Probing of regulators can be a slow operation and can contribute to
slower boot times. This is especially true if a regulator is turned on
at probe time (with regulator-boot-on or regulator-always-on) and the
regulator requires delays (off-on-time, ramp time, etc).
While the overall kernel is not ready to switch to async probe by
default, as per the discussion on the mailing lists [1] it is believed
that the regulator subsystem is in good shape and we can move
regulator drivers over wholesale. There is no way to just magically
opt in all regulators (regulators are just normal drivers like
platform_driver), so we set PROBE_PREFER_ASYNCHRONOUS for all
regulators found in 'drivers/regulator' individually.
Given the number of drivers touched and the impossibility to test this
ahead of time, it wouldn't be shocking at all if this caused a
regression for someone. If there is a regression caused by this patch,
it's likely to be one of the cases talked about in [1]. As a "quick
fix", drivers involved in the regression could be fixed by changing
them to PROBE_FORCE_SYNCHRONOUS. That being said, the correct fix
would be to directly fix the problem that caused the issue with async
probe.
The approach here follows a similar approach that was used for the mmc
subsystem several years ago [2]. In fact, I ran nearly the same python
script to auto-generate the changes. The only thing I changed was to
search for "i2c_driver", "spmi_driver", and "spi_driver" in addition
to "platform_driver".
[1] https://lore.kernel.org/r/06db017f-e985-4434-8d1d-02ca2100cca0@sirena.org.uk
[2] https://lore.kernel.org/r/20200903232441.2694866-1-dianders@chromium.org/
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20230316125351.1.I2a4677392a38db5758dee0788b2cea5872562a82@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
This is very close to a straight revert of commit 218320fec2
("regulator: core: Fix off-on-delay-us for always-on/boot-on
regulators"). We've identified that patch as causing a boot speed
regression on sc7180-trogdor boards. While boot speed certainly isn't
more important than making sure that power sequencing is correct,
looking closely at the original change it doesn't seem to have been
fully justified. It mentions "cycling issues" without describing
exactly what the issues were. That means it's possible that the
cycling issues were really a problem that should be fixed in a
different way.
Let's take a careful look at how we should handle regulators that have
an off-on-delay and that are boot-on or always-on. Linux currently
doesn't have any way to identify whether a GPIO regulator was already
on when the kernel booted. That means that when the kernel boots we
probe a regulator, see that it wants boot-on / always-on we, and then
turn the regulator on. We could be in one of two cases when we do
this:
a) The regulator might have been left on by the bootloader and we're
ensuring that it stays on.
b) The regulator might have been left off by the bootloader and we're
just now turning it on.
For case a) we definitely don't need any sort of delay. For case b) we
_might_ need some delay in case the bootloader turned the regulator
off _right_ before booting the kernel. To get the proper delay for
case b) then we can just assume a `last_off` of 0, which is what it
gets initialized to by default.
As per above, we can't tell whether we're in case a) or case b) so
we'll assume the longer delay (case b). This basically puts the code
to how it was before commit 218320fec2 ("regulator: core: Fix
off-on-delay-us for always-on/boot-on regulators"). However, we add
one important change: we make sure that the delay is actually honored
if `last_off` is 0. Though the original "cycling issues" cited were
vague, I'm hopeful that this important extra change will be enough to
fix the issues that the initial commit mentioned.
With this fix, I've confined that on a sc7180-trogdor board the delay
at boot goes down from 500 ms to ~250 ms. That's not as good as the 0
ms that we had prior to commit 218320fec2 ("regulator: core: Fix
off-on-delay-us for always-on/boot-on regulators"), but it's probably
safer because we don't know if the bootloader turned the regulator off
right before booting.
One note is that it's possible that we could be in a state that's not
a) or b) if there are other issues in the kernel. The only one I can
think of is related to pinctrl. If the pinctrl driver being used on a
board isn't careful about avoiding glitches when setting up a pin then
it's possible that setting up a pin could cause the regulator to "turn
off" briefly immediately before the regulator probes. If this is
indeed causing problems then the pinctrl driver should be fixed,
perhaps in a similar way to what was done in commit d21f4b7ffc
("pinctrl: qcom: Avoid glitching lines when we first mux to output")
Fixes: 218320fec2 ("regulator: core: Fix off-on-delay-us for always-on/boot-on regulators")
Cc: Christian Kohlschütter <christian@kohlschutter.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20230313111806.1.I2eaad872be0932a805c239a7c7a102233fb0b03b@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver can be compile tested with !CONFIG_OF making certain data
unused:
drivers/regulator/mt6397-regulator.c:400:34: error: ‘mt6397_of_match’ defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230310214553.275450-4-krzysztof.kozlowski@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver can be compile tested with !CONFIG_OF making certain data
unused:
drivers/regulator/mp8859.c:132:34: error: ‘mp8859_dt_id’ defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230310214553.275450-3-krzysztof.kozlowski@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver can be compile tested with !CONFIG_OF making certain data
unused:
drivers/regulator/max20086-regulator.c:289:34: error: ‘max20086_dt_ids’ defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20230310214553.275450-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver can be compile tested with !CONFIG_OF making certain data
unused:
drivers/regulator/lp872x.c:931:34: error: ‘lp872x_dt_ids’ defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230310214553.275450-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
It is preferred to use typed property access functions (i.e.
of_property_read_<type> functions) rather than low-level
of_get_property/of_find_property functions for reading properties.
Convert reading boolean properties to to of_property_read_bool().
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230310144722.1544843-1-robh@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
It is preferred to use typed property access functions (i.e.
of_property_read_<type> functions) rather than low-level
of_get_property/of_find_property functions for reading properties. As
part of this, convert of_get_property/of_find_property calls to the
recently added of_property_present() helper when we just want to test
for presence of a property and nothing more.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230310144721.1544756-1-robh@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The RT5739 is a step-down switching voltage regulator that supports
output voltage ragne from 300mV to 1300mV with the wide input supply
voltage range from 2.5V to 5.5V.
Signed-off-by: ChiYuan Huang <cy_huang@richtek.com>
Link: https://lore.kernel.org/r/1676599618-24819-3-git-send-email-cy_huang@richtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The thermal zone device structure is exposed to the different drivers
and obviously they access the internals while that should be
restricted to the core thermal code.
In order to self-encapsulate the thermal core code, we need to prevent
the drivers accessing directly the thermal zone structure and provide
accessor functions to deal with.
Use the devdata accessor introduced in the previous patch.
No functional changes intended.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Ido Schimmel <idosch@nvidia.com> #mlxsw
Acked-by: Gregory Greenman <gregory.greenman@intel.com> #iwlwifi
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com> #power_supply
Acked-by: Damien Le Moal <damien.lemoal@opensource.wdc.com> #ahci
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Two fixes here, one driver fix for incorrect error codes and a fix in
the core to use ktime_get_boottime() in order to fix accounting of the
time regulators have been powered down over suspend, ktime_get()
pauses over suspend which is not what we want.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmP/tZ4ACgkQJNaLcl1U
h9C0Wwf/XZb6kH1Ar70cVJPBxifze0PgsfwMxP6Pfi6PUuZkWldggZqt3SEBicyg
7aaoTavPg9XRbVBfMS9AYjnGe+AjWcltCzF8im4OGMFrbRWdyDX27iJOCacPJn6A
B7D3waWHiO811zArqf/Xy6hCOJRHtXE29mDruW2K1q4vYpc3mUsrd0C0s6k1575B
AxaZxbndsCKsFfZMZ0ruPl9lt8ziEQiW6uBk9TXSThoAtCOaydDWFJF0EbQykX9q
ks/Oh6ge5gXBoiEQX4bpd1BxRYx/enMK2LwMm86Imbg9dGPJa5YAfZkXIfQSAXfy
F4HVlQVhcUaFvTM44G+bdiyowppFCw==
=PSq9
-----END PGP SIGNATURE-----
Merge tag 'regulator-fix-v6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"Two fixes here, one driver fix for incorrect error codes and a fix in
the core to use ktime_get_boottime() in order to fix accounting of the
time regulators have been powered down over suspend. ktime_get()
pauses over suspend which is not what we want"
* tag 'regulator-fix-v6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: core: Use ktime_get_boottime() to determine how long a regulator was off
regulator: max597x: Fix error return code in max597x_get_status
For regulators with 'off-on-delay-us' the regulator framework currently
uses ktime_get() to determine how long the regulator has been off
before re-enabling it (after a delay if needed). A problem with using
ktime_get() is that it doesn't account for the time the system is
suspended. As a result a regulator with a longer 'off-on-delay' (e.g.
500ms) that was switched off during suspend might still incurr in a
delay on resume before it is re-enabled, even though the regulator
might have been off for hours. ktime_get_boottime() accounts for
suspend time, use it instead of ktime_get().
Fixes: a8ce7bd896 ("regulator: core: Fix off_on_delay handling")
Cc: stable@vger.kernel.org # 5.13+
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20230223003301.v2.1.I9719661b8eb0a73b8c416f9c26cf5bd8c0563f99@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
This has been a very quiet release for the regulator API, there's one
new driver for the Maxim MAX20411, some DT schema conversions and some
small tweaks and improvements but really nothing major at all.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmPza80ACgkQJNaLcl1U
h9BJkAf7B/o0QVtyCyJSsoJ9QelMjq8Pbps5aEYlwhSnqZQtJnZEcX3NucJJuLBJ
IQ4K6XbDZtyODzRvB+Xy2/1QPEJC94oaxEN8Cw1rjolsJ8IL7NOa+h56gTRNouw+
7DlbAbM3EcmwiizZT74Hw4yqYkTUWsrN0K/O5ygs5sL/QfDV1LTnWTqoympoTgeN
UDk3B8VMmWmQ83i04oX/lZ28h9iKs8KVoB5rNRWHi0ypF/LMiADm1WWbhsou+vtO
uJp7UzTqQiIXkLBgKv2Oz0i4cFHNFnBDyTT8M8hL76xs/R94K1gTidSMoZremJ0F
RZX0UWHBK5fF24HIWKdzc+Iz57lgUA==
=FSkC
-----END PGP SIGNATURE-----
Merge tag 'regulator-v6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"This has been a very quiet release for the regulator API: there's one
new driver for the Maxim MAX20411, some DT schema conversions and some
small tweaks and improvements but really nothing major at all"
* tag 'regulator-v6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (22 commits)
regulator: max597x: Align for simple_mfd_i2c driver
regulator: max20411: Fix off-by-one for n_voltages setting
regulator: max597x: Remove unused variable
regulator: tps65219: use generic set_bypass()
regulator: s5m8767: Bounds check id indexing into arrays
regulator: max77802: Bounds check regulator id against opmode
regulator: max20411: Convert to i2c's .probe_new()
regulator: scmi: Allow for zero voltage domains
regulator: max20411: Directly include bitfield.h
regulator: Introduce Maxim MAX20411 Step-Down converter
regulator: dt-bindings: Describe Maxim MAX20411
regulator: dt-bindings: qcom-labibb: Allow regulator-common properties
regulator: dt-bindings: fixed-regulator: allow gpios property
regulator: tps65219: use IS_ERR() to detect an error pointer
regulator: mcp16502: add enum MCP16502_REG_HPM description
regulator: fixed-helper: use the correct function name in comment
regulator: act8945a: fix non-kernel-doc comments
dt-bindings: regulators: convert non-smd RPM Regulators bindings to dt-schema
regulator: dt-bindings: Convert Fairchild FAN53555 to DT schema
regulator: dt-bindings: qcom,usb-vbus-regulator: change node name
...
REGULATOR_FAILED_RETRY should not be used in max597x_get_status error path.
Othewise, the regulator core will treat it as REGULATOR_STATUS_ON.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Link: https://lore.kernel.org/r/20230220105614.356187-1-axel.lin@ingics.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use regmap provided by simple_mfd_i2c driver and remove unused variable.
Identify device variant by checking compatible property in DT.
Signed-off-by: Naresh Solanki <Naresh.Solanki@9elements.com>
Link: https://lore.kernel.org/r/20230216075302.68935-1-Naresh.Solanki@9elements.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The compiler has no way to know if "id" is within the array bounds of
the regulators array. Add a check for this and a build-time check that
the regulators and reg_voltage_map arrays are sized the same. Seen with
GCC 13:
../drivers/regulator/s5m8767.c: In function 's5m8767_pmic_probe':
../drivers/regulator/s5m8767.c:936:35: warning: array subscript [0, 36] is outside array bounds of 'struct regulator_desc[37]' [-Warray-bounds=]
936 | regulators[id].vsel_reg =
| ~~~~~~~~~~^~~~
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: linux-samsung-soc@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230128005358.never.313-kees@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Explicitly bounds-check the id before accessing the opmode array. Seen
with GCC 13:
../drivers/regulator/max77802-regulator.c: In function 'max77802_enable':
../drivers/regulator/max77802-regulator.c:217:29: warning: array subscript [0, 41] is outside array bounds of 'unsigned int[42]' [-Warray-bounds=]
217 | if (max77802->opmode[id] == MAX77802_OFF_PWRREQ)
| ~~~~~~~~~~~~~~~~^~~~
../drivers/regulator/max77802-regulator.c:62:22: note: while referencing 'opmode'
62 | unsigned int opmode[MAX77802_REG_MAX];
| ^~~~~~
Cc: Javier Martinez Canillas <javier@dowhile0.org>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://lore.kernel.org/r/20230127225203.never.864-kees@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
SCMI Voltage protocol allows the platform to report no voltage domains
on discovery, while warning the user about such an odd configuration.
As a consequence this condition should not be treated as error by the SCMI
regulator driver either.
Allow SCMI regulator driver to probe successfully even when no voltage
domains are discovered.
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Link: https://lore.kernel.org/r/20230126180511.766373-1-cristian.marussi@arm.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The max20411 driver uses bitfield.h but does not directly include
it, add an inclusion to avoid build errors in configurations
which do not result in an implicit inclusion.
Signed-off-by: Mark Brown <broonie@kernel.org>
Introduce a driver to control the Maxim MAX20411 family of
high-efficiency, syncrhonous step-down converters.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Link: https://lore.kernel.org/r/20230124184440.1421074-3-quic_bjorande@quicinc.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add description for MCP16502_REG_HPM to prevent a kernel-doc warning:
drivers/regulator/mcp16502.c:90: warning: Enum value 'MCP16502_REG_HPM' not described in enum 'mcp16502_reg'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20230117070139.28905-1-rdunlap@infradead.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the correct function name and modify the function short description.
This prevents a kernel-doc warning:
drivers/regulator/fixed-helper.c:32: warning: expecting prototype for regulator_register_fixed_name(). Prototype was for regulator_register_always_on() instead
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20230113064421.11986-1-rdunlap@infradead.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Don't use kernel-doc "/**" markers for comments that are not in
kernel-doc format. This prevents these warnings:
drivers/regulator/act8945a-regulator.c:19: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* ACT8945A Global Register Map.
drivers/regulator/act8945a-regulator.c:50: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* Field Definitions.
drivers/regulator/act8945a-regulator.c:56: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* ACT8945A Voltage Number
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20230113064412.11038-1-rdunlap@infradead.org
Signed-off-by: Mark Brown <broonie@kernel.org>
This fixes the definition of the PM8550 ldo11 regulator matching it's
capabilities since this LDO is designed to work between 1,2V and 1,5V.
Fixes: e6e3776d68 ("regulator: qcom-rpmh: Add support for PM8550 regulators")
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20230102-topic-sm8550-upstream-fixes-reg-l11b-nldo-v1-1-d97def246338@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Make the error message more useful by reporting the actual regulator
name if devm_regulator_register() fails.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Link: https://lore.kernel.org/r/20221214153409.1270213-1-w.egorov@phytec.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Two core fixes here, one for a long standing race which some Qualcomm
systems have started triggering with their UFS driver and another fixing
a problem with supply lookup introduced by the fixes for devm related
use after free issues that were introduced in this merge window.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmOmHd4ACgkQJNaLcl1U
h9A8hQf/fTezN966/Rp9tvP9YJOPmluqoqDxp/kbyfs3wXlhGR51rytXk/h0DDUD
U8VYIzIyJ7RyqNRtbSqoaNKTCq73Z2/eWl3O/Tsw/mVbpsPHbgDFG4qmM3wE88Rm
u6tOFHouTMQPSJ1yDWJrnR627uRQsnjmJbElSkSWXGWVtJnBqbj+QPGal+hXR/lv
0Fo3nvKvLG5W7GkRh7rRTBu+reJAM4piFQzWxWStiyQwgRLZzpPbgXmpPfto7J5L
WeRMEJkprUVdps+DuylnsHHPD1EA0sBwvs5FQ7yKFuWoejZLC/loW51uColwiIOw
uhQlLzm8WwLePjYQPatHDegxu056fg==
=YhNZ
-----END PGP SIGNATURE-----
Merge tag 'regulator-fix-v6.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"Two core fixes here, one for a long standing race which some Qualcomm
systems have started triggering with their UFS driver and another
fixing a problem with supply lookup introduced by the fixes for devm
related use after free issues that were introduced in this merge
window"
* tag 'regulator-fix-v6.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: core: fix deadlock on regulator enable
regulator: core: Fix resolve supply lookup issue
When updating the operating mode as part of regulator enable, the caller
has already locked the regulator tree and drms_uA_update() must not try
to do the same in order not to trigger a deadlock.
The lock inversion is reported by lockdep as:
======================================================
WARNING: possible circular locking dependency detected
6.1.0-next-20221215 #142 Not tainted
------------------------------------------------------
udevd/154 is trying to acquire lock:
ffffc11f123d7e50 (regulator_list_mutex){+.+.}-{3:3}, at: regulator_lock_dependent+0x54/0x280
but task is already holding lock:
ffff80000e4c36e8 (regulator_ww_class_acquire){+.+.}-{0:0}, at: regulator_enable+0x34/0x80
which lock already depends on the new lock.
...
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(regulator_ww_class_acquire);
lock(regulator_list_mutex);
lock(regulator_ww_class_acquire);
lock(regulator_list_mutex);
*** DEADLOCK ***
just before probe of a Qualcomm UFS controller (occasionally) deadlocks
when enabling one of its regulators.
Fixes: 9243a195be ("regulator: core: Change voltage setting path")
Fixes: f8702f9e4a ("regulator: core: Use ww_mutex for regulators locking")
Cc: stable@vger.kernel.org # 5.0
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20221215104646.19818-1-johan+linaro@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
From Marek's log, the previous change modify the parent of rdev.
https://lore.kernel.org/all/58b92e75-f373-dae7-7031-8abd465bb874@samsung.com/
In 'regulator_resolve_supply', it uses the parent DT node of rdev as the
DT-lookup starting node. But the parent DT node may not exist. This will
cause the NULL supply issue.
This patch modify the parent of rdev back to the device that provides
from 'regulator_config' in 'regulator_register'.
Fixes: 8f3cbcd6b4 ("regulator: core: Use different devices for resource allocation and DT lookup")
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: ChiYuan Huang <cy_huang@richtek.com>
Link: https://lore.kernel.org/r/1670981831-12583-1-git-send-email-u0084500@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Quite a quiet release for regulator, the diffstat is dominated by the
I2C migration to probe_new() and the newly added MT6357 driver. We've
just one framework addition and the rest is all new device support,
fixes and cleanups.
The framework addition is an API for requesting all regulators defined
in DT, this isn't great practice but has reasonable applications when
there is generic code handling devices on buses where the bus
specification doesn't include power. The immediate application is MDIO
but I believe there's others, it's another API that'll need an eye
keeping on it for undesirable usage.
- An API for requesting all regulators defined in DT.
- Conversion of lots of drivers to the I2C probe_new() API.
- Support for Mediatek MT6357, Qualcomm PM8550, PMR735a and
Richtek RT6190.
There's a cross tree merge with the I2C tree in order to use the new
i2c_client_get_device_id() helper in the conversions to probe_new().
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmOXIIcACgkQJNaLcl1U
h9DW8Af/SkLjUIhuMYrln1QBKvJfMOzAIOo8LeCRCU6E8IxsDu/zccEva6dqr/M/
DFkq5VBCH7cX7VIvaHLjED/VdM0n+JG35tzwv83TVuAohLW/qsRdO6RE9IRBJcUd
7wUj2gjUBjjnCwbpI0hTygqQHvIxO0deQVYoQsxF8VwJTQ+ufpA3TJ3tmxqeWvbd
N/qkLohCk9NoFgiMjzBxBonacaZEvHkjUtqRthHm/nx8Mdu9NhBb6ai6KIpN7EJD
CaY+nUOx/cW8YJWBaZ32bcnvRgtanJGWn+p49/JmUCu0lIEOX2r7jds/kBo/hWWl
akGDUTcmvZY0CfrJfbx+FJxcA1A7Jg==
=Dmpg
-----END PGP SIGNATURE-----
Merge tag 'regulator-v6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"Quite a quiet release for regulator, the diffstat is dominated by the
I2C migration to probe_new() and the newly added MT6357 driver. We've
just one framework addition and the rest is all new device support,
fixes and cleanups.
The framework addition is an API for requesting all regulators defined
in DT, this isn't great practice but has reasonable applications when
there is generic code handling devices on buses where the bus
specification doesn't include power. The immediate application is MDIO
but I believe there's others, it's another API that'll need an eye
keeping on it for undesirable usage.
Summary:
- An API for requesting all regulators defined in DT
- Conversion of lots of drivers to the I2C probe_new() API
- Support for Mediatek MT6357, Qualcomm PM8550, PMR735a and Richtek
RT6190"
* tag 'regulator-v6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (56 commits)
regulator: core: Use different devices for resource allocation and DT lookup
dt-bindings: Add missing 'unevaluatedProperties' to regulator nodes
regulator: qcom-labibb: Fix missing of_node_put() in qcom_labibb_regulator_probe()
regulator: add mt6357 regulator
regulator: dt-bindings: Add binding schema for mt6357 regulators
regulator: core: fix resource leak in regulator_register()
regulator: core: fix module refcount leak in set_supply()
regulator: core: fix use_count leakage when handling boot-on
regulator: rk808: Use dev_err_probe
regulator: rk808: reduce 'struct rk808' usage
regulator: Drop obsolete dependencies on COMPILE_TEST
regulator: pv88080-regulator: Convert to i2c's .probe_new()
regulator: pfuze100-regulator: Convert to i2c's .probe_new()
regulator: isl6271a-regulator: Convert to i2c's .probe_new()
regulator: fan53555: Convert to i2c's .probe_new()
regulator: act8865-regulator: Convert to i2c's .probe_new()
regulator: qcom-rpmh: Add support for PM8550 regulators
regulator: dt-bindings: qcom,rpmh: Add compatible for PM8550
regulator: tps65023-regulator: Convert to i2c's .probe_new()
regulator: tps62360-regulator: Convert to i2c's .probe_new()
...
Following by the below discussion, there's the potential UAF issue
between regulator and mfd.
https://lore.kernel.org/all/20221128143601.1698148-1-yangyingliang@huawei.com/
From the analysis of Yingliang
CPU A |CPU B
mt6370_probe() |
devm_mfd_add_devices() |
|mt6370_regulator_probe()
| regulator_register()
| //allocate init_data and add it to devres
| regulator_of_get_init_data()
i2c_unregister_device() |
device_del() |
devres_release_all() |
// init_data is freed |
release_nodes() |
| // using init_data causes UAF
| regulator_register()
It's common to use mfd core to create child device for the regulator.
In order to do the DT lookup for init data, the child that registered
the regulator would pass its parent as the parameter. And this causes
init data resource allocated to its parent, not itself. The issue happen
when parent device is going to release and regulator core is still doing
some operation of init data constraint for the regulator of child device.
To fix it, this patch expand 'regulator_register' API to use the
different devices for init data allocation and DT lookup.
Reported-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: ChiYuan Huang <cy_huang@richtek.com>
Link: https://lore.kernel.org/r/1670311341-32664-1-git-send-email-u0084500@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The reg_node needs to be released through of_node_put() in the error
handling path when of_irq_get_byname() failed.
Fixes: 390af53e04 ("regulator: qcom-labibb: Implement short-circuit and over-current IRQs")
Signed-off-by: Yuan Can <yuancan@huawei.com>
Link: https://lore.kernel.org/r/20221203062109.115043-1-yuancan@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add regulator driver for the MT6357 PMIC.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Alexandre Mergnat <amergnat@baylibre.com>
Link: https://lore.kernel.org/r/20221005-mt6357-support-v7-7-477e60126749@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
If create_regulator() fails in set_supply(), the module refcount
needs be put to keep refcount balanced.
Fixes: e2c09ae7a7 ("regulator: core: Increase refcount for regulator supply's module")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221201122706.4055992-2-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
I found a use_count leakage towards supply regulator of rdev with
boot-on option.
┌───────────────────┐ ┌───────────────────┐
│ regulator_dev A │ │ regulator_dev B │
│ (boot-on) │ │ (boot-on) │
│ use_count=0 │◀──supply──│ use_count=1 │
│ │ │ │
└───────────────────┘ └───────────────────┘
In case of rdev(A) configured with `regulator-boot-on', the use_count
of supplying regulator(B) will increment inside
regulator_enable(rdev->supply).
Thus, B will acts like always-on, and further balanced
regulator_enable/disable cannot actually disable it anymore.
However, B was also configured with `regulator-boot-on', we wish it
could be disabled afterwards.
Signed-off-by: Rui Zhang <zr.zhang@vivo.com>
Link: https://lore.kernel.org/r/20221201033806.2567812-1-zr.zhang@vivo.com
Signed-off-by: Mark Brown <broonie@kernel.org>
If the system does not come from reset (like when it is kexec()), the
regulator might have an IRQ waiting for us.
If we enable the IRQ handler before its structures are ready, we crash.
This patch fixes:
[ 1.141839] Unable to handle kernel read from unreadable memory at virtual address 0000000000000078
[ 1.316096] Call trace:
[ 1.316101] blocking_notifier_call_chain+0x20/0xa8
[ 1.322757] cpu cpu0: dummy supplies not allowed for exclusive requests
[ 1.327823] regulator_notifier_call_chain+0x1c/0x2c
[ 1.327825] da9211_irq_handler+0x68/0xf8
[ 1.327829] irq_thread+0x11c/0x234
[ 1.327833] kthread+0x13c/0x154
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Reviewed-by: Adam Ward <DLG-Adam.Ward.opensource@dm.renesas.com>
Link: https://lore.kernel.org/r/20221124-da9211-v2-0-1779e3c5d491@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Print error message for potential EPROBE_DEFER error using
dev_err_probe, which captures the reason in
/sys/kernel/debug/devices_deferred and otherwise silences
the message.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20221020204251.108565-12-sebastian.reichel@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Reduce usage of 'struct rk808' (driver data of the parent MFD), so
that only the chip variant field is still being accessed directly.
This allows restructuring the MFD driver to support SPI based
PMICs.
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20221020204251.108565-3-sebastian.reichel@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This is more changes than I'd like this late although the diffstat is
still fairly small, I kept on holding off as new fixes came in to give
things time to soak in -next but should probably have tagged and sent an
additional pull request earlier.
There's some relatively large fixes to the twl6030 driver to fix issues
with the TWL6032 variant which resulted from some work on the core
TWL6030 driver, a couple of fixes for error handling paths (mostly in
the core), and a nice stability fix for the sgl51000 driver that's been
pulled out of a BSP.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmOBOHkACgkQJNaLcl1U
h9DSNwf+KFunln/2mpx6UrLa5kl5QQGDtBruEcEBkKnUAx/YZlZ2nFT08bV4V1D0
/STa4PZdThem89VBRClQvxdyPE4qKIUvWsLmTUXF9P48m11bI+PMGCBMoKgjs4ZL
jMTZi/JD+4oZcJcOG5Qu3rihdBxotrsvlk2QUMs+PaPx2JPyr1CpBXAseMkVcqrD
QzyRWUgCjS2bfnc9Xd7gll1MXeSIcN2oD14ec//5Wv0KItGs2i0cOCUY+U4Dffus
b+75g7sU4znCD6bcycKdTJEqcqrotrZycGnq3K36ycrAGulQrH4SwohEc2PUlnUa
ZrKBjC6iFkSutk0dYlSz4k7AfRzjrw==
=kf38
-----END PGP SIGNATURE-----
Merge tag 'regulator-fix-v6.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"This is more changes than I'd like this late although the diffstat is
still fairly small, I kept on holding off as new fixes came in to give
things time to soak in -next but should probably have tagged and sent
an additional pull request earlier.
There's some relatively large fixes to the twl6030 driver to fix
issues with the TWL6032 variant which resulted from some work on the
core TWL6030 driver, a couple of fixes for error handling paths
(mostly in the core), and a nice stability fix for the sgl51000 driver
that's been pulled out of a BSP"
* tag 'regulator-fix-v6.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: twl6030: fix get status of twl6032 regulators
regulator: twl6030: re-add TWL6032_SUBCLASS
regulator: slg51000: Wait after asserting CS pin
regulator: core: fix UAF in destroy_regulator()
regulator: rt5759: fix OOB in validate_desc()
regulator: core: fix kobject release warning and memory leak in regulator_register()
Since commit 0166dc11be ("of: make CONFIG_OF user selectable"), it
is possible to test-build any driver which depends on OF on any
architecture by explicitly selecting OF. Therefore depending on
COMPILE_TEST as an alternative is no longer needed.
It is actually better to always build such drivers with OF enabled,
so that the test builds are closer to how each driver will actually be
built on its intended target. Building them without OF may not test
much as the compiler will optimize out potentially large parts of the
code. In the worst case, this could even pop false positive warnings.
Dropping COMPILE_TEST here improves the quality of our testing and
avoids wasting time on non-existent issues.
As a minor optimization, this also lets us drop several occurrences of
of_match_ptr(), __maybe_unused and some ifdef guarding, as we now know
what all of this will resolve to, we might as well save cpp some work.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Icenowy Zheng <icenowy@aosc.io>
Link: https://lore.kernel.org/r/20221124144708.64371b98@endymion.delvare
Signed-off-by: Mark Brown <broonie@kernel.org>
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-for-MFD-by: Lee Jones <lee@kernel.org>
Acked-for-Backlight-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20221118224540.619276-555-uwe@kleine-koenig.org
Signed-off-by: Mark Brown <broonie@kernel.org>
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-for-MFD-by: Lee Jones <lee@kernel.org>
Acked-for-Backlight-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20221118224540.619276-554-uwe@kleine-koenig.org
Signed-off-by: Mark Brown <broonie@kernel.org>
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-for-MFD-by: Lee Jones <lee@kernel.org>
Acked-for-Backlight-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20221118224540.619276-543-uwe@kleine-koenig.org
Signed-off-by: Mark Brown <broonie@kernel.org>
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-for-MFD-by: Lee Jones <lee@kernel.org>
Acked-for-Backlight-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20221118224540.619276-542-uwe@kleine-koenig.org
Signed-off-by: Mark Brown <broonie@kernel.org>
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-for-MFD-by: Lee Jones <lee@kernel.org>
Acked-for-Backlight-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20221118224540.619276-539-uwe@kleine-koenig.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Matti Vaittinen <mazziesaccount@gmail.com>:
Minor (printing) improvements for ROHM regulator drivers.
This series:
- Drops an unnecessary info print from bd718x7.
(Added a fixes tag for this but not really sure if worth
adding to stable)
- Convert the ROHM BDxxxxx PMIC regulator drivers to use dev_err_probe().
- Change the probe logic for bd718x7 to favor the more usual devm-style
where errors are returned immediately.
Add the rpmh regulators found in PM8550 PMIC and its variants,
along with their compatibles and configuration data. They also
contain some FT-SMPS 525, so add their configuration as well.
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20221123153638.721254-3-abel.vesa@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-for-MFD-by: Lee Jones <lee@kernel.org>
Acked-for-Backlight-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20221118224540.619276-560-uwe@kleine-koenig.org
Signed-off-by: Mark Brown <broonie@kernel.org>
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-for-MFD-by: Lee Jones <lee@kernel.org>
Acked-for-Backlight-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20221118224540.619276-558-uwe@kleine-koenig.org
Signed-off-by: Mark Brown <broonie@kernel.org>
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-for-MFD-by: Lee Jones <lee@kernel.org>
Acked-for-Backlight-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20221118224540.619276-552-uwe@kleine-koenig.org
Signed-off-by: Mark Brown <broonie@kernel.org>
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-for-MFD-by: Lee Jones <lee@kernel.org>
Acked-for-Backlight-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20221118224540.619276-550-uwe@kleine-koenig.org
Signed-off-by: Mark Brown <broonie@kernel.org>
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-for-MFD-by: Lee Jones <lee@kernel.org>
Acked-for-Backlight-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20221118224540.619276-547-uwe@kleine-koenig.org
Signed-off-by: Mark Brown <broonie@kernel.org>
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-for-MFD-by: Lee Jones <lee@kernel.org>
Acked-for-Backlight-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20221118224540.619276-545-uwe@kleine-koenig.org
Signed-off-by: Mark Brown <broonie@kernel.org>
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Acked-for-MFD-by: Lee Jones <lee@kernel.org>
Acked-for-Backlight-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20221118224540.619276-540-uwe@kleine-koenig.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Use kfree_const() to free supply_name conditionally in create_regulator()
as supply_name may be allocated from kmalloc() or directly from .rodata
section.
Fixes: 87fe29b61f ("regulator: push allocations in create_regulator() outside of lock")
Signed-off-by: Wang ShaoBo <bobo.shaobowang@huawei.com>
Link: https://lore.kernel.org/r/20221123034616.3609537-1-bobo.shaobowang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The dev_err_probe() has (at least) following benefits over dev_err()
when printing an error print for a failed function call at a device
driver probe:
- Omit error level print if error is 'EPRBE_DEFER'
- Standardized print format for returned error
- return the error value allowing shortening calls like:
if (ret) {
dev_err(...);
return ret;
}
to
if (ret)
return dev_err_probe(...);
Convert the ROHM BD718x7 regulator driver to use the dev_err_probe() when
returned error is not hard-coded constant.
NOTE:
This commit also changes the error handling path to return immediately
from a spot where the error is spotted instead of using a single point
of exit.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://lore.kernel.org/r/fee54c2d04bb41b51381e31523f9ed31575206d2.1669203610.git.mazziesaccount@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The dev_err_probe() has (at least) following benefits over dev_err()
when printing an error print for a failed function call at a device
driver probe:
- Omit error level print if error is 'EPRBE_DEFER'
- Standardized print format for returned error
- return the error value allowing shortening calls like:
if (ret) {
dev_err(...);
return ret;
}
to
if (ret)
return dev_err_probe(...);
Convert the ROHM BD71828, ROHM BD71815 and ROHM BD9576 regulator drivers
to use the dev_err_probe() when returned error is not hard-coded constant.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://lore.kernel.org/r/0b644da4a8f58558ffe474d2593f85c46de2f965.1669203610.git.mazziesaccount@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
A device-tree node name was printed when bd718x7 driver's feedback-loop
feature was developed. This print was accidentally left in driver. The
info-level print just pollutes the log.
Drop unnecessary pr_info()
Fixes: d2ad981151 ("regulator: bd718x7: Support external connection to scale voltages")
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://lore.kernel.org/r/33fd99abf2451999938fef4ba6cf7b3f19e9b992.1669203610.git.mazziesaccount@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-for-MFD-by: Lee Jones <lee@kernel.org>
Acked-for-Backlight-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20221118224540.619276-559-uwe@kleine-koenig.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-for-MFD-by: Lee Jones <lee@kernel.org>
Acked-for-Backlight-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20221118224540.619276-557-uwe@kleine-koenig.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-for-MFD-by: Lee Jones <lee@kernel.org>
Acked-for-Backlight-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20221118224540.619276-556-uwe@kleine-koenig.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-for-MFD-by: Lee Jones <lee@kernel.org>
Acked-for-Backlight-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20221118224540.619276-553-uwe@kleine-koenig.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-for-MFD-by: Lee Jones <lee@kernel.org>
Acked-for-Backlight-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20221118224540.619276-551-uwe@kleine-koenig.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-for-MFD-by: Lee Jones <lee@kernel.org>
Acked-for-Backlight-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20221118224540.619276-549-uwe@kleine-koenig.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-for-MFD-by: Lee Jones <lee@kernel.org>
Acked-for-Backlight-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20221118224540.619276-548-uwe@kleine-koenig.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-for-MFD-by: Lee Jones <lee@kernel.org>
Acked-for-Backlight-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20221118224540.619276-546-uwe@kleine-koenig.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-for-MFD-by: Lee Jones <lee@kernel.org>
Acked-for-Backlight-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20221118224540.619276-544-uwe@kleine-koenig.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-for-MFD-by: Lee Jones <lee@kernel.org>
Acked-for-Backlight-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20221118224540.619276-541-uwe@kleine-koenig.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The Arizona and Madera codecs all have a datasheet name of "MICVDD"
for the regulator output. But future codecs with a regulator that
can be controlled by this driver have different naming convention
for the output of the regulator.
Move the setting of the supply name from arizona_micsupp_common_init()
to arizona_micsupp_probe() and madera_micsupp_probe().
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20221109165331.29332-8-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When Madera support was added to this driver the code was left
using ARIZONA_* defines. This wasn't causing any problem because
those defines just happened to have the same value as the
equivalent MADERA_* defines. But it is not ideal to assume this,
and future devices that can share this driver do not have the
same register map.
Fix the code to refer to the register data in struct regulator_desc.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20221109165331.29332-7-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Status is reported as always off in the 6032 case. Status
reporting now matches the logic in the setters. Once of
the differences to the 6030 is that there are no groups,
therefore the state needs to be read out in the lower bits.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Link: https://lore.kernel.org/r/20221120221208.3093727-3-andreas@kemnade.info
Signed-off-by: Mark Brown <broonie@kernel.org>
In former times, info->feature was populated via the parent driver
by pdata/regulator_init_data->driver_data for all regulators when
USB_PRODUCT_ID_LSB indicates a TWL6032.
Today, the information is not set, so re-add it at the regulator
definitions.
Fixes: 25d8233770 ("regulator: twl: make driver DT only")
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Link: https://lore.kernel.org/r/20221120221208.3093727-2-andreas@kemnade.info
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Corentin Labbe <clabbe@baylibre.com>:
This adds a new regulator_bulk_get_all() which grab all supplies
properties in a DT node, for use in implementing generic handling
for things like MDIO PHYs where the physical standardisation of
the bus does not extend to power supplies.
It work exactly like regulator_bulk_get() but instead of working on a
provided list of names, it seek all consumers properties matching
xxx-supply.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Link: https://lore.kernel.org/r/20221115073603.3425396-2-clabbe@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Sony's downstream driver [1], among some other changes, adds a
seemingly random 10ms usleep_range, which turned out to be necessary
for the hardware to function properly on at least Sony Xperia 1 IV.
Without this, I2C transactions with the SLG51000 straight up fail.
Relax (10-10ms -> 10-11ms) and add the aforementioned sleep to make
sure the hardware has some time to wake up.
(nagara-2.0.0-mlc/vendor/semc/hardware/camera-kernel-module/)
[1] https://developer.sony.com/file/download/open-source-archive-for-64-0-m-4-29/
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20221118131035.54874-1-konrad.dybcio@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
I got a UAF report as following:
==================================================================
BUG: KASAN: use-after-free in __lock_acquire+0x935/0x2060
Read of size 8 at addr ffff88810e838220 by task python3/268
Call Trace:
<TASK>
dump_stack_lvl+0x67/0x83
print_report+0x178/0x4b0
kasan_report+0x90/0x190
__lock_acquire+0x935/0x2060
lock_acquire+0x156/0x400
_raw_spin_lock+0x2a/0x40
lockref_get+0x11/0x30
simple_recursive_removal+0x41/0x440
debugfs_remove.part.12+0x32/0x50
debugfs_remove+0x29/0x30
_regulator_put.cold.54+0x3e/0x27f
regulator_put+0x1f/0x30
release_nodes+0x6a/0xa0
devres_release_all+0xf8/0x150
Allocated by task 37:
kasan_save_stack+0x1c/0x40
kasan_set_track+0x21/0x30
__kasan_slab_alloc+0x5d/0x70
slab_post_alloc_hook+0x62/0x510
kmem_cache_alloc_lru+0x222/0x5a0
__d_alloc+0x31/0x440
d_alloc+0x30/0xf0
d_alloc_parallel+0xc4/0xd20
__lookup_slow+0x15e/0x2f0
lookup_one_len+0x13a/0x150
start_creating+0xea/0x190
debugfs_create_dir+0x1e/0x210
create_regulator+0x254/0x4e0
_regulator_get+0x2a1/0x467
_devm_regulator_get+0x5a/0xb0
regulator_virtual_probe+0xb9/0x1a0
Freed by task 30:
kasan_save_stack+0x1c/0x40
kasan_set_track+0x21/0x30
kasan_save_free_info+0x2a/0x50
__kasan_slab_free+0x102/0x190
kmem_cache_free+0xf6/0x600
rcu_core+0x54c/0x12b0
__do_softirq+0xf2/0x5e3
Last potentially related work creation:
kasan_save_stack+0x1c/0x40
__kasan_record_aux_stack+0x98/0xb0
call_rcu+0x42/0x700
dentry_free+0x6c/0xd0
__dentry_kill+0x23b/0x2d0
dput.part.31+0x431/0x780
simple_recursive_removal+0xa9/0x440
debugfs_remove.part.12+0x32/0x50
debugfs_remove+0x29/0x30
regulator_unregister+0xe3/0x230
release_nodes+0x6a/0xa0
==================================================================
Here is how happened:
processor A processor B
regulator_register()
rdev_init_debugfs()
rdev->debugfs = debugfs_create_dir()
devm_regulator_get()
rdev = regulator_dev_lookup()
create_regulator(rdev)
// using rdev->debugfs as parent
debugfs_create_dir(rdev->debugfs)
mfd_remove_devices_fn()
release_nodes()
regulator_unregister()
// free rdev->debugfs
debugfs_remove_recursive(rdev->debugfs)
release_nodes()
destroy_regulator()
debugfs_remove_recursive() <- causes UAF
In devm_regulator_get(), after getting rdev, the refcount
is get, so fix this by moving debugfs_remove_recursive()
to regulator_dev_release(), then it can be proctected by
the refcount, the 'rdev->debugfs' can not be freed until
the refcount is 0.
Fixes: 5de705194e ("regulator: Add basic per consumer debugfs")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221116033706.3595812-1-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
I got the following OOB report:
BUG: KASAN: slab-out-of-bounds in validate_desc+0xba/0x109
Read of size 8 at addr ffff888107db8ff0 by task python3/253
Call Trace:
<TASK>
dump_stack_lvl+0x67/0x83
print_report+0x178/0x4b0
kasan_report+0x90/0x190
validate_desc+0xba/0x109
gpiod_set_value_cansleep+0x40/0x5a
regulator_ena_gpio_ctrl+0x93/0xfc
_regulator_do_enable.cold.61+0x89/0x163
set_machine_constraints+0x140a/0x159c
regulator_register.cold.73+0x762/0x10cd
devm_regulator_register+0x57/0xb0
rt5759_probe+0x3a0/0x4ac [rt5759_regulator]
The desc used in validate_desc() is passed from 'reg_cfg.ena_gpiod',
which is not initialized. Fix this by initializing 'reg_cfg' to 0.
Fixes: 7b36ddb208 ("regulator: rt5759: Add support for Richtek RT5759 DCDC converter")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221116092943.1668326-1-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Here is a warning report about lack of registered release()
from kobject lib:
Device '(null)' does not have a release() function, it is broken and must be fixed.
WARNING: CPU: 0 PID: 48430 at drivers/base/core.c:2332 device_release+0x104/0x120
Call Trace:
kobject_put+0xdc/0x180
put_device+0x1b/0x30
regulator_register+0x651/0x1170
devm_regulator_register+0x4f/0xb0
When regulator_register() returns fail and directly goto `clean` symbol,
rdev->dev has not registered release() function yet (which is registered
by regulator_class in the following), so rdev needs to be freed manually.
If rdev->dev.of_node is not NULL, which means the of_node has gotten by
regulator_of_get_init_data(), it needs to call of_node_put() to avoid
refcount leak.
Otherwise, only calling put_device() would lead memory leak of rdev
in further:
unreferenced object 0xffff88810d0b1000 (size 2048):
comm "107-i2c-rtq6752", pid 48430, jiffies 4342258431 (age 1341.780s)
backtrace:
kmalloc_trace+0x22/0x110
regulator_register+0x184/0x1170
devm_regulator_register+0x4f/0xb0
When regulator_register() returns fail and goto `wash` symbol,
rdev->dev has registered release() function, so directly call
put_device() to cleanup everything.
Fixes: d3c731564e ("regulator: plug of_node leak in regulator_register()'s error path")
Signed-off-by: Zeng Heng <zengheng4@huawei.com>
Link: https://lore.kernel.org/r/20221116074339.1024240-1-zengheng4@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
I got the the following report:
OF: ERROR: memory leak, expected refcount 1 instead of 2,
of_node_get()/of_node_put() unbalanced - destroy cset entry:
attach overlay node /i2c/pmic@62/regulators/exten
In of_get_regulator(), the node is returned from of_parse_phandle()
with refcount incremented, after using it, of_node_put() need be called.
Fixes: 69511a452e ("regulator: map consumer regulator based on device tree")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221115091508.900752-1-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
PMR735a is already supported in the RPMH regulator driver, but
there are cases where it's bundled with SMD RPM SoCs. Port it over
to qcom_smd-regulator to enable usage in such cases.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20221109110846.45789-2-konrad.dybcio@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Zev Weiss <zev@bewilderbeest.net>:
This series adds support for userspace-controlled regulator-supplied
power outputs [2]. This is an important feature for some kinds of BMC
(baseboard management controller) systems where the BMC provides an
operator with manual control of a set of DC power outputs.
As in a broadly similar patchset that was recently almost merged [0],
this takes the approach of providing support by extending the existing
userspace-consumer regulator driver. A couple questions about the
userspace-consumer driver came up along the way, however.
First, how (if at all) is it currently being used? It appears the
last in-tree use of it was removed a bit over two years ago in commit
9d3239147d ("ARM: pxa: remove Compulab pxa2xx boards"). Aside from
just adding DT support I've made a couple small tweaks to the driver
in patch 3 that I hope are compatible with any current usage, but
without any extant examples to look at it's kind of hard to say.
Second, how critical is its support for controlling multiple
regulators? (i.e. its use of regulator_bulk_data and friends instead
of a single struct regulator.) As far as I can see every in-tree use
of it that's ever existed has used num_supplies = 1. If it's not
important to retain, patch 1 of this series could be supplanted by one
that instead simplifies the driver slightly by removing that
functionality.
The DT binding added in patch 2 is essentially identical to one I
posted in a previous patchset that had an R-B from Rob [1], but has
had some minor rewording and been moved from the extcon subsystem to
the regulator subsystem.
In addition to adding some fairly simple OF support code, we make some
slight adjustments to the userspace-consumer driver to properly
support use with regulator-output hardware:
- We now do an exclusive get of the supply regulators so as to
prevent regulator_init_complete_work from automatically disabling
them.
- Instead of assuming that the supply is initially disabled, we now
query its state to determine the initial value of drvdata->enabled.
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Link: https://lore.kernel.org/r/20221031233704.22575-4-zev@bewilderbeest.net
Signed-off-by: Mark Brown <broonie@kernel.org>
We had an exclusive variant of the devm_regulator_get() API, but no
corresponding variant for the bulk API; let's add one now. We add a
generalized version of the existing regulator_bulk_get() function that
additionally takes a get_type parameter and redefine
regulator_bulk_get() in terms of it, then do similarly with
devm_regulator_bulk_get(), and finally add the new
devm_regulator_bulk_get_exclusive().
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Link: https://lore.kernel.org/r/20221031233704.22575-2-zev@bewilderbeest.net
Signed-off-by: Mark Brown <broonie@kernel.org>
The core work this time around has mostly been around the code to manage
regulator modes, simplifying the interface for configuring modes to not
take account of the voltage and as a side effect resolving a
bootstrapping issue on systems where we can't read the voltage from the
regulator. Otherwise it's been quite a quiet release with some new
drivers and a devm helper:
- Make the load handling in the Qualcomm RPMH regulators much more
idiomatic and general cleanups to the handling of load configuration.
- devm helper for a combined get and enable operation.
- Support for MediaTek MT6331, Qualcomm PM660, 660L and PM6125, Texas
Instruments TPS65219.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmM61ZQACgkQJNaLcl1U
h9BGggf+MraXhaTOSrLCzKYjcsjIZ2OCzySoKPdh9PdvnKc2PX+vIi6SYjq6zeAe
OlwDvKzW+bR6VRTStSskK5wRXrLn/9eo25GhZyl4BpAR+vjGBtzlNagk3gGTBKMj
ua/kb16FV+15Zg5L1qO35ka9BuCzs2Bfz9OoZKy4vtuqVqazmrU3PS8nr/kAlW9R
fi7a50Ybc+W7xBYUNuaKqdFQWlblLh/UKqImV9dANokXZDD9deJ8BeWq/FttNY6T
lyTJGDuKYhcvb7wx8QdzcSCoLsdVPRi0cmIlbjiusWogyvJBQVhto338Y8+b7vIJ
29tlD54gmWXSxwf0e8CpHKh/BxwbAw==
=YFsi
-----END PGP SIGNATURE-----
Merge tag 'regulator-v6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"The core work this time around has mostly been around the code to
manage regulator modes, simplifying the interface for configuring
modes to not take account of the voltage and as a side effect
resolving a bootstrapping issue on systems where we can't read the
voltage from the regulator.
Otherwise it's been quite a quiet release with some new drivers and a
devm helper:
- Make the load handling in the Qualcomm RPMH regulators much more
idiomatic and general cleanups to the handling of load
configuration
- devm helper for a combined get and enable operation
- Support for MediaTek MT6331, Qualcomm PM660, 660L and PM6125, Texas
Instruments TPS65219"
* tag 'regulator-v6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (45 commits)
dt-bindings: gpio-regulator: add vin-supply property support
regulator: gpio: Add input_supply support in gpio_regulator_config
regulator: tps65219: Fix is_enabled checking in tps65219_set_bypass
regulator: qcom,rpmh: add pm660 and pm660l pmics
regulator: qcom-rpmh: add pm660 and pm660l pmics
regulator: of: Fix kernel-doc
regulator: of: Fix kernel-doc
regulator: Add driver for MT6332 PMIC regulators
regulator: Add bindings for MT6332 regulator
regulator: Add driver for MT6331 PMIC regulators
regulator: Add bindings for MT6331 regulator
regulator: tps65219: Fix .bypass_val_on setting
regulator: qcom_rpm: Fix circular deferral regression
regulator: core: Prevent integer underflow
regulator: dt-bindings: qcom,rpmh: Indicate regulator-allow-set-load dependencies
regulator: bd9576: switch to using devm_fwnode_gpiod_get()
regulator: bd71815: switch to using devm_fwnode_gpiod_get()
regulator: core: Fix regulator supply registration with sysfs
regulator: tps65219: change tps65219_regulator_irq_types to static
regulator: core: Don't err if allow-set-load but no allowed-modes
...
fixes all over the tree. Other subsystems depending on this change
have been asked to pull an immutable topic branch for this.
* new driver for Microchip PCI1xxxx switch
* heavy refactoring of the Mellanox BlueField driver
* we prefer async probe in the i801 driver now
* the rest is usual driver updates (support for more SoCs, some
refactoring, some feature additions)
-----BEGIN PGP SIGNATURE-----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=arni
-----END PGP SIGNATURE-----
Merge tag 'i2c-for-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
- 'remove' callback converted to return void. Big change with trivial
fixes all over the tree. Other subsystems depending on this change
have been asked to pull an immutable topic branch for this.
- new driver for Microchip PCI1xxxx switch
- heavy refactoring of the Mellanox BlueField driver
- we prefer async probe in the i801 driver now
- the rest is usual driver updates (support for more SoCs, some
refactoring, some feature additions)
* tag 'i2c-for-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (37 commits)
i2c: pci1xxxx: prevent signed integer overflow
i2c: acpi: Replace zero-length array with DECLARE_FLEX_ARRAY() helper
i2c: i801: Prefer async probe
i2c: designware-pci: Use standard pattern for memory allocation
i2c: designware-pci: Group AMD NAVI quirk parts together
i2c: microchip: pci1xxxx: Add driver for I2C host controller in multifunction endpoint of pci1xxxx switch
docs: i2c: slave-interface: return errno when handle I2C_SLAVE_WRITE_REQUESTED
i2c: mlxbf: remove device tree support
i2c: mlxbf: support BlueField-3 SoC
i2c: cadence: Add standard bus recovery support
i2c: mlxbf: add multi slave functionality
i2c: mlxbf: support lock mechanism
macintosh/ams: Adapt declaration of ams_i2c_remove() to earlier change
i2c: riic: Use devm_platform_ioremap_resource()
i2c: mlxbf: remove IRQF_ONESHOT
dt-bindings: i2c: rockchip: add rockchip,rk3128-i2c
dt-bindings: i2c: renesas,rcar-i2c: Add r8a779g0 support
i2c: tegra: Add GPCDMA support
i2c: scmi: Convert to be a platform driver
i2c: rk3x: Add rv1126 support
...
- Rework the device tree initialization, convert the drivers to the
new API and remove the old OF code (Daniel Lezcano).
- Fix return value to -ENODEV when searching for a specific thermal
zone which does not exist (Daniel Lezcano).
- Fix the return value inspection in of_thermal_zone_find() (Dan
Carpenter).
- Fix kernel panic when KASAN is enabled as it detects use after
free when unregistering a thermal zone (Daniel Lezcano).
- Move the set_trip ops inside the therma sysfs code (Daniel Lezcano).
- Remove unnecessary error message as it is already shown in the
underlying function (Jiapeng Chong).
- Rework the monitoring path and move the locks upper in the call
stack to fix some potentials race windows (Daniel Lezcano).
- Fix lockdep_assert() warning introduced by the lock rework (Daniel
Lezcano).
- Do not lock thermal zone mutex in the user space governor (Rafael
Wysocki).
- Revert the Mellanox 'hotter thermal zone' feature because it is
already handled in the thermal framework core code (Daniel Lezcano).
- Increase maximum number of trip points in the thermal core (Sumeet
Pawnikar).
- Replace strlcpy() with unused retval with strscpy() in the core
thermal control code (Wolfram Sang).
- Use module_pci_driver() macro in the int340x processor_thermal
driver (Shang XiaoJing).
- Use get_cpu() instead of smp_processor_id() in the intel_powerclamp
thermal driver to prevent it from crashing and remove unused
accounting for IRQ wakes from it (Srinivas Pandruvada).
- Consolidate priv->data_vault checks in int340x_thermal (Rafael
Wysocki).
- Check the policy first in cpufreq_cooling_register() (Xuewen Yan).
- Drop redundant error message from da9062-thermal (zhaoxiao).
- Drop of_match_ptr() from thermal_mmio (Jean Delvare).
-----BEGIN PGP SIGNATURE-----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=Ufw7
-----END PGP SIGNATURE-----
Merge tag 'thermal-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull thermal control updates from Rafael Wysocki:
"The most significant part of this update is the thermal control DT
initialization rework from Daniel Lezcano and the following conversion
of drivers to use the new API introduced by it
Apart from that, the maximum number of trip points in a thermal zone
is increased and there are some fixes and code cleanups
Specifics:
- Rework the device tree initialization, convert the drivers to the
new API and remove the old OF code (Daniel Lezcano)
- Fix return value to -ENODEV when searching for a specific thermal
zone which does not exist (Daniel Lezcano)
- Fix the return value inspection in of_thermal_zone_find() (Dan
Carpenter)
- Fix kernel panic when KASAN is enabled as it detects use after free
when unregistering a thermal zone (Daniel Lezcano)
- Move the set_trip ops inside the therma sysfs code (Daniel Lezcano)
- Remove unnecessary error message as it is already shown in the
underlying function (Jiapeng Chong)
- Rework the monitoring path and move the locks upper in the call
stack to fix some potentials race windows (Daniel Lezcano)
- Fix lockdep_assert() warning introduced by the lock rework (Daniel
Lezcano)
- Do not lock thermal zone mutex in the user space governor (Rafael
Wysocki)
- Revert the Mellanox 'hotter thermal zone' feature because it is
already handled in the thermal framework core code (Daniel Lezcano)
- Increase maximum number of trip points in the thermal core (Sumeet
Pawnikar)
- Replace strlcpy() with unused retval with strscpy() in the core
thermal control code (Wolfram Sang)
- Use module_pci_driver() macro in the int340x processor_thermal
driver (Shang XiaoJing)
- Use get_cpu() instead of smp_processor_id() in the intel_powerclamp
thermal driver to prevent it from crashing and remove unused
accounting for IRQ wakes from it (Srinivas Pandruvada)
- Consolidate priv->data_vault checks in int340x_thermal (Rafael
Wysocki)
- Check the policy first in cpufreq_cooling_register() (Xuewen Yan)
- Drop redundant error message from da9062-thermal (zhaoxiao)
- Drop of_match_ptr() from thermal_mmio (Jean Delvare)"
* tag 'thermal-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (55 commits)
thermal: core: Increase maximum number of trip points
thermal: int340x: processor_thermal: Use module_pci_driver() macro
thermal: intel_powerclamp: Remove accounting for IRQ wakes
thermal: intel_powerclamp: Use get_cpu() instead of smp_processor_id() to avoid crash
thermal: int340x_thermal: Consolidate priv->data_vault checks
thermal: cpufreq_cooling: Check the policy first in cpufreq_cooling_register()
thermal: Drop duplicate words from comments
thermal: move from strlcpy() with unused retval to strscpy()
thermal: da9062-thermal: Drop redundant error message
thermal/drivers/thermal_mmio: Drop of_match_ptr()
thermal: gov_user_space: Do not lock thermal zone mutex
Revert "mlxsw: core: Add the hottest thermal zone detection"
thermal/core: Fix lockdep_assert() warning
thermal/core: Move the mutex inside the thermal_zone_device_update() function
thermal/core: Move the thermal zone lock out of the governors
thermal/governors: Group the thermal zone lock inside the throttle function
thermal/core: Rework the monitoring a bit
thermal/core: Rearm the monitoring only one time
thermal/drivers/qcom/spmi-adc-tm5: Remove unnecessary print function dev_err()
thermal/of: Remove old OF code
...
This is simillar as fixed-regulator.
Used to extract regulator parent from the device tree.
Without that property used, the parent regulator can be shut down (if not an always on).
Thus leading to inappropriate behavior:
On am62-SP-SK this fix is required to avoid tps65219 ldo1 (SDMMC rail) to be shut down after boot completion.
Signed-off-by: Jerome Neanne <jneanne@baylibre.com>
Link: https://lore.kernel.org/r/20220929132526.29427-2-jneanne@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a specific MFD_SY7636A config option.
As part of this change we can use MFD_SY7636A as a dependency for all
SY7636a components and also remove the name from MFD_SIMPLE_MFD_I2C as
it no longer needs to be selectable.
Signed-off-by: Alistair Francis <alistair@alistair23.me>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20220525115554.430971-2-alistair@alistair23.me
Testing .enable cannot tell if a regulator is enabled or not, check return
value of .is_enabled() instead.
Also remove unneeded ret variable.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Link: https://lore.kernel.org/r/20220919122353.384171-1-axel.lin@ingics.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The SDM630 and SDM660 both use RPM (not RPMh) for managing the PM660 and
PM660L. The SDM670 uses RPMh to manage them as PMIC 4s. To support the
SDM670, add the PM660 and PM660L to the RPMh regulator driver.
Link: 58064f13c0%5E%21/#F0
Link: f676d3d24f%5E%21/#F3
Signed-off-by: Richard Acayan <mailingradian@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220920223331.150635-3-mailingradian@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>:
In an effort to give some love to the apparently forgotten MT6795 SoC,
I am upstreaming more components that are necessary to support platforms
powered by this one apart from a simple boot to serial console.
This series adds support for the regulators found in MT6331 and MT6332
main/companion PMICs.
Adding support to each driver in each subsystem is done in different
patch series as to avoid spamming uninteresting patches to maintainers.
Tested on a MT6795 Sony Xperia M5 (codename "Holly") smartphone.
The .bypass_val_on setting does not match the .bypass_mask setting, so the
.bypass_mask bit will never get set. Fix it by removing .bypass_val_on
setting, the regulator_set_bypass_regmap and regulator_get_bypass_regmap
helpers will use rdev->desc->bypass_mask as val_on if the val_on is 0.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Link: https://lore.kernel.org/r/20220828120153.1512508-1-axel.lin@ingics.com
Signed-off-by: Mark Brown <broonie@kernel.org>
On recent kernels, the PM8058 L16 (or any other PM8058 LDO-regulator)
does not come up if they are supplied by an SMPS-regulator. This
is not very strange since the regulators are registered in a long
array and the L-regulators are registered before the S-regulators,
and if an L-regulator defers, it will never get around to registering
the S-regulator that it needs.
See arch/arm/boot/dts/qcom-apq8060-dragonboard.dts:
pm8058-regulators {
(...)
vdd_l13_l16-supply = <&pm8058_s4>;
(...)
Ooops.
Fix this by moving the PM8058 S-regulators first in the array.
Do the same for the PM8901 S-regulators (though this is currently
not causing any problems with out device trees) so that the pattern
of registration order is the same on all PMnnnn chips.
Fixes: 087a1b5cdd ("regulator: qcom: Rework to single platform device")
Cc: stable@vger.kernel.org
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <andersson@kernel.org>
Cc: Konrad Dybcio <konrad.dybcio@somainline.org>
Cc: linux-arm-msm@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20220909112529.239143-1-linus.walleij@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
By using a ratio of delay to poll_enabled_time that is not integer
time_remaining underflows and does not exit the loop as expected.
As delay could be derived from DT and poll_enabled_time is defined
in the driver this can easily happen.
Use a signed iterator to make sure that the loop exits once
the remaining time is negative.
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Link: https://lore.kernel.org/r/20220909125954.577669-1-patrick.rudolph@9elements.com
Signed-off-by: Mark Brown <broonie@kernel.org>
One core fix here improving the error handling on enable failure, plus
smaller fixes for the pfuze100 drive and the SPMI DT bindings.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmMZ3IUACgkQJNaLcl1U
h9CwbQf6AzcfEH0QTrQrkJV5m0lWfpxSdmxWg2NSmKDsCUTEg4KKV86+iGbOax1y
StciVjWKBQ7nTwX7d2tWYL67ogziN4ePFdroKzIHMkj50+qWfy1KsopsWgm6joYj
YCfWro3f2LHD7CC70qsd1yoVV4mO+yzdwkc0qtxQe4l9rvsdfA8VH80MjGyWaxUO
dz8BjLAk3ivCsCTCGFkL3k51HLm7ORbX8ruCqFnW3a6neblliIP/z+MkNhLgZC7q
+P3GGbBYYs1d9Ay5IIM04FszhJEOfG7RSeqMosi6gCl2r8Vw3UNJ7rUyH/cGTwyV
eZFTgd89kiVg1I97FxbI4Wb1SjPg0A==
=97j3
-----END PGP SIGNATURE-----
Merge tag 'regulator-fix-v6.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"One core fix here improving the error handling on enable failure, plus
smaller fixes for the pfuze100 drive and the SPMI DT bindings"
* tag 'regulator-fix-v6.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: Fix qcom,spmi-regulator schema
regulator: pfuze100: Fix the global-out-of-bounds access in pfuze100_regulator_probe()
regulator: core: Clean up on enable failure
I would like to stop exporting OF-specific devm_gpiod_get_from_of_node()
so that gpiolib can be cleaned a bit, so let's switch to the generic
fwnode property API.
While at it switch the rest of the calls to read properties in
bd957x_probe() to the generic device property API as well.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://lore.kernel.org/r/20220903-gpiod_get_from_of_node-remove-v1-9-b29adfb27a6c@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
I would like to stop exporting OF-specific devm_gpiod_get_from_of_node()
so that gpiolib can be cleaned a bit, so let's switch to the generic
fwnode property API.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://lore.kernel.org/r/20220903-gpiod_get_from_of_node-remove-v1-8-b29adfb27a6c@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In "regulator: core: Resolve supply name earlier to prevent
double-init", we introduced a bug that prevented the regulator names
from registering properly with sysfs.
Reorder regulator_register such that supply names are properly resolved
and registered.
Fixes: 8a866d527a ("regulator: core: Resolve supply name earlier to prevent double-init")
Link: https://lore.kernel.org/all/58b92e75-f373-dae7-7031-8abd465bb874@samsung.com/
Signed-off-by: Christian Kohlschütter <christian@kohlschutter.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20220829165543.24856-1-christian@kohlschutter.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Apparently the device trees of some boards have the property
"regulator-allow-set-load" for some of their regulators but then they
don't specify anything for "regulator-allowed-modes". That's not
really legit, but...
...before commit efb0cb50c4 ("regulator: qcom-rpmh: Implement
get_optimum_mode(), not set_load()") they used to get away with it, at
least on boards using RPMH regulators. That's because when a regulator
driver implements set_load() then the core doesn't look at
"regulator-allowed-modes" when trying to automatically adjust things
in response to the regulator's load. The core doesn't know what mode
we'll end up in, so how could it validate it?
Said another way: before commit efb0cb50c4 ("regulator: qcom-rpmh:
Implement get_optimum_mode(), not set_load()") some boards _were_
having the regulator mode adjusted despite listing no allowed
modes. After commit efb0cb50c4 ("regulator: qcom-rpmh: Implement
get_optimum_mode(), not set_load()") these same boards were now
getting an error returned when trying to use their regulators, since
simply enabling a regulator tries to update its load and that was
failing.
We don't really want to go back to the behavior from before commit
efb0cb50c4 ("regulator: qcom-rpmh: Implement get_optimum_mode(), not
set_load()"). Boards shouldn't have been changing modes if no allowed
modes were listed. However, the behavior after commit efb0cb50c4
("regulator: qcom-rpmh: Implement get_optimum_mode(), not set_load()")
isn't the best because now boards can't even turn their regulators on.
Let's choose to detect this case and return "no error" from
drms_uA_update(). The net-result will be _different_ behavior than we
had before commit efb0cb50c4 ("regulator: qcom-rpmh: Implement
get_optimum_mode(), not set_load()"), but this new behavior seems more
correct. If a board truly needed the mode switched then its device
tree should be updated to list the allowed modes.
Reported-by: Andrew Halaney <ahalaney@redhat.com>
Fixes: efb0cb50c4 ("regulator: qcom-rpmh: Implement get_optimum_mode(), not set_load()")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Andrew Halaney <ahalaney@redhat.com>
Link: https://lore.kernel.org/r/20220824142229.RFT.v2.2.I6f77860e5cd98bf5c67208fa9edda4a08847c304@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
The get_optimum_mode() for regulator drivers is passed the input
voltage and output voltage as well as the current. This is because, in
theory, the optimum mode can depend on all three things.
It turns out that for all regulator drivers in mainline only the
current is looked at when implementing get_optimum_mode(). None of the
drivers take the input or output voltage into account. Despite the
fact that none of the drivers take the input or output voltage into
account, though, the regulator framework will error out before calling
into get_optimum_mode() if it doesn't know the input or output
voltage.
The above behavior turned out to be a probelm for some boards when we
landed commit efb0cb50c4 ("regulator: qcom-rpmh: Implement
get_optimum_mode(), not set_load()"). Before that change we'd have no
problems running drms_uA_update() for RPMH regulators even if a
regulator's input or output voltage was unknown. After that change
drms_uA_update() started to fail. This is because typically boards
using RPMH regulators don't model the input supplies of RPMH
regulators. Input supplies for RPMH regulators nearly always come from
the output of other RPMH regulators (or always-on regulators) and RPMH
firmware is initialized with this knowledge and handles enabling (and
adjusting the voltage of) input supplies. While we could model the
parent/child relationship of the regulators in Linux, many boards
don't bother since it adds extra overhead.
Let's change the regulator core to make things work again. Now if we
fail to get the input or output voltage we'll still call into
get_optimum_mode() and we'll just pass error codes in for input_uV
and/or output_uV parameters.
Since no existing regulator drivers even look at input_uV and
output_uV we don't need to add this error handling anywhere right
now. We'll add some comments in the core so that it's obvious that (if
regulator drivers care) it's up to them to add the checks.
Reported-by: Andrew Halaney <ahalaney@redhat.com>
Fixes: efb0cb50c4 ("regulator: qcom-rpmh: Implement get_optimum_mode(), not set_load()")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Andrew Halaney <ahalaney@redhat.com>
Link: https://lore.kernel.org/r/20220824142229.RFT.v2.1.I137e6bef4f6d517be7b081be926059321102fd3d@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
The pfuze_chip::regulator_descs is an array of size
PFUZE100_MAX_REGULATOR, the pfuze_chip::pfuze_regulators
is the pointer to the real regulators of a specific device.
The number of real regulator is supposed to be less than
the PFUZE100_MAX_REGULATOR, so we should use the size of
'regulator_num * sizeof(struct pfuze_regulator)' in memcpy().
This fixes the out of bounds access bug reported by KASAN.
Signed-off-by: Xiaolei Wang <xiaolei.wang@windriver.com>
Link: https://lore.kernel.org/r/20220825111922.1368055-1-xiaolei.wang@windriver.com
Signed-off-by: Mark Brown <broonie@kernel.org>
new API and remove the old OF code (Daniel Lezcano)
- Fix return value to -ENODEV when searching for a specific thermal
zone which does not exist (Daniel Lezcano)
- Fix the return value inspection in of_thermal_zone_find() (Dan
Carpenter)
- Fix kernel panic when kasan is enabled as it detects an use after
free when unregistering a thermal zone (Daniel Lezcano)
- Move the set_trip ops inside the therma sysfs code (Daniel Lezcano)
- Remove unnecessary error message as it is already showed in the
underlying function (Jiapeng Chong)
- Rework the monitoring path and move the locks upper in the call
stack to fix some potentials race windows (Daniel Lezcano)
- Fix lockdep_assert() warning introduced by the lock rework (Daniel
Lezcano)
- Revert the Mellanox 'hotter thermal zone' feature because it is
already handled in the thermal framework core code (Daniel Lezcano)
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGn3N4YVz0WNVyHskqDIjiipP6E8FAmMEyhwACgkQqDIjiipP
6E8+AAf/QFLCn1CzLsWCvHC+i4+CjoX/d/1ZhX24mZm17llBdSP5zGxlCVNCRAk/
xabT62WUbRsIzG0lCYAGUYXDUQf6qjs1QJ/fMZxtwoyHJA0yc3BtIlhxlnezpcA/
Dvfu0gu3NaZvf/yIl+PWrEJP6ZXmPzpiiYdtCZIReB+L1XR0tSJ49bxP+QIaN5JH
EXOmO0Y0XLG9jGshUS4xJrej9QQcTvgpbLGy/QLS43sdmmXHOkfbjvl1i4CPFeo3
14ENCsGm5wXAS1UHDRluoasgPUXTlG809aVzeh6pBcHzWn/90K8XeNA+lCbL8k23
hiXrpYX2Xhgy1vibyB7DW1bzQYOYxQ==
=wF0H
-----END PGP SIGNATURE-----
Merge tag 'thermal-v6.1-rc1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/thermal/linux
Pull thermal control changes for v6.1-rc1 from Daniel Lezcano:
"- Rework the device tree initialization, convert the drivers to the
new API and remove the old OF code (Daniel Lezcano)
- Fix return value to -ENODEV when searching for a specific thermal
zone which does not exist (Daniel Lezcano)
- Fix the return value inspection in of_thermal_zone_find() (Dan
Carpenter)
- Fix kernel panic when KASAN is enabled as it detects use after
free when unregistering a thermal zone (Daniel Lezcano)
- Move the set_trip ops inside the therma sysfs code (Daniel Lezcano)
- Remove unnecessary error message as it is already showed in the
underlying function (Jiapeng Chong)
- Rework the monitoring path and move the locks upper in the call
stack to fix some potentials race windows (Daniel Lezcano)
- Fix lockdep_assert() warning introduced by the lock rework (Daniel
Lezcano)
- Revert the Mellanox 'hotter thermal zone' feature because it is
already handled in the thermal framework core code (Daniel Lezcano)"
* tag 'thermal-v6.1-rc1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/thermal/linux: (46 commits)
Revert "mlxsw: core: Add the hottest thermal zone detection"
thermal/core: Fix lockdep_assert() warning
thermal/core: Move the mutex inside the thermal_zone_device_update() function
thermal/core: Move the thermal zone lock out of the governors
thermal/governors: Group the thermal zone lock inside the throttle function
thermal/core: Rework the monitoring a bit
thermal/core: Rearm the monitoring only one time
thermal/drivers/qcom/spmi-adc-tm5: Remove unnecessary print function dev_err()
thermal/of: Remove old OF code
thermal/core: Move set_trip_temp ops to the sysfs code
thermal/drivers/samsung: Switch to new of thermal API
regulator/drivers/max8976: Switch to new of thermal API
Input: sun4i-ts - switch to new of thermal API
iio/drivers/sun4i_gpadc: Switch to new of thermal API
hwmon/drivers/core: Switch to new of thermal API
hwmon: pm_bus: core: Switch to new of thermal API
ata/drivers/ahci_imx: Switch to new of thermal API
thermal/drivers/ti-soc: Switch to new of API
thermal/drivers/hisilicon: Switch to new of API
thermal/drivers/maxim: Switch to new of API
...
Return the value from regmap_write() directly instead of storing it
in another redundant variable.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: ye xingchen <ye.xingchen@zte.com.cn>
Link: https://lore.kernel.org/r/20220824074707.221159-1-ye.xingchen@zte.com.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Iskren Chernev <iskren.chernev@gmail.com>:
This patch series adds SPMI and SMD regulator support for the PM6125 found on
SM4250/SM6115 SoCs from QCom.
This code has been tested on:
* OnePlus Nord N100 (oneplus,billie2, SoC sm4250)
* Redmi 9T (redmi,lemon, SoC sm6115)
The main source used for this change is qpnp pm6125 support patch from caf [1]:
[1]: https://source.codeaurora.org/quic/la/kernel/msm-5.4/commit/?h=kernel.lnx.5.4.r1-rel&id=d1220daeffaa440ffff0a8c47322eb0033bf54f5
v3: https://lkml.org/lkml/2022/7/31/303
v2: https://lkml.org/lkml/2022/7/26/885
v1: https://lkml.org/lkml/2021/8/28/144
Changes from v3:
- fix compilation issue reported by kernel test robot
- reorder HFSMPS/LDO+FTSMPS patches
- add new slew-rate computation for HFSMPS
- add proper pull-down support for new regs
- name new regs/vals after HFSMPS instead of FTSMPS
- address indentation/newline issues reported by Krzysztof
- improve commit messages on SPMI/RPM related patches
Changes from v2:
- split spmi new regulator support in 2 patches
- FTS and LDOs now have set_load and set_pull_down ops
- add better commit messages on spmi patches
- fix sob header order
- fix tested device info (Redmi 9T, NOT Xiaomi 9T)
- improve formatting in spmi binding docs
- sort alphabetically in smd binding docs
- sort alphabetically spmi pmics
- sort alphabetically smd pmics
Changes from v1:
- add dt-bindings
- split SPMI patch into new reg types and the new PMIC
- add correct supply mapping
Iskren Chernev (13):
dt-bindings: regulator: qcom_spmi: Improve formatting of if-then
blocks
dt-bindings: regulator: qcom_spmi: Document PM6125 PMIC
dt-bindings: regulator: qcom_smd: Sort compatibles alphabetically
dt-bindings: regulator: qcom_smd: Document PM6125 PMIC
regulator: qcom_spmi: Add support for HFSMPS regulator type
regulator: qcom_spmi: Add support for LDO_510 and FTSMPS
regulator: qcom_spmi: Sort pmics alphabetically (part 1)
regulator: qcom_spmi: Sort pmics alphabetically (part 2)
regulator: qcom_spmi: Add PM6125 PMIC support
regulator: qcom_smd: Sort pmics alphabetically (part 1)
regulator: qcom_smd: Sort pmics alphabetically (part 2)
regulator: qcom_smd: Sort pmics alphabetically (part 3)
regulator: qcom_smd: Add PM6125 RPM regulators
.../regulator/qcom,smd-rpm-regulator.yaml | 26 +-
.../regulator/qcom,spmi-regulator.yaml | 32 ++
drivers/regulator/qcom_smd-regulator.c | 400 ++++++++++--------
drivers/regulator/qcom_spmi-regulator.c | 378 ++++++++++++-----
4 files changed, 551 insertions(+), 285 deletions(-)
--
2.37.1
The regulators set consists of 3 bucks DCDCs and 4 LDOs. The output
voltages are configurable and are meant to supply power to the
main processor and other components.
Validation:
Visual check: cat /sys/kernel/debug/regulator/regulator_summary
Validation: userspace-consumer and virtual-regulator required
to test further
Enable/Disable:
cat /sys/devices/platform/userspace-consumer-VDDSHV_SD_IO_PMIC/state
echo disabled > /sys/devices/platform/
userspace-consumer-VDDSHV_SD_IO_PMIC/state
echo enabled > /sys/devices/platform/
userspace-consumer-VDDSHV_SD_IO_PMIC/state
Change voltage:
cat /sys/devices/platform/regulator-virtual-ldo1/min_microvolts
echo 1000000 > /sys/devices/platform/regulator-virtual-ldo1/
min_microvolts
echo 3000000 > /sys/devices/platform/regulator-virtual-ldo1/
max_microvolts
Signed-off-by: Jerome Neanne <jneanne@baylibre.com>
Link: https://lore.kernel.org/r/20220805121852.21254-9-jneanne@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for PM6125 PMIC which is found on SM4250/6115 SoCs.
S1, S2, S3, S4, S8 are FTS+FTSMPS_510, rev 2
- range is 0.3-1.372V by 4mV increments
S5, S6, s7 are BUCK+HFSMPS_510, rev 4
- range is 0.32-2.04V by 8mV increment
L1, L3, L7 are LDO+N600_510, rev 2
L2, L4, L8, L17, L18 are LDO+N300_510, rev 2
L6 is LDO+N1200_510, rev 2
- range is 0.32-1.304V by 8mV increment
L5 is LDO+MV_P50_510, rev 2
L15, L19, L20 are LDO+MV_P150_510, rev 2
L21, L22, L23, L24 are LDO+MV_P600_510, rev 2
- range is 1.504-3.544V by 8mV increment
L9, L11, L14 are LDO+LV_P600_510, rev 2
L10, L16 are LDO+LV_P150_510, rev 2
L12, L13 are LDO+LV_P300_510, rev 2
- range 1.504-2V by 8mV increment
Signed-off-by: Adam Skladowski <a39.skl@gmail.com>
Signed-off-by: Iskren Chernev <iskren.chernev@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20220802221112.2280686-10-iskren.chernev@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This is preparation for supporing PM6125.
The HFSMPS is a BUCK type regulator with subtype 0x0a, same as the
existing HFS430 regulator.
Even though the HFSMPS and HFS430 share a type and subtype, the HFSMPS has
an updated register map, including different mode values, moved pull down
register, and different slew rate address and formula.
In addition to NORMAL (NPM), FAST (AUTO_LPM) and IDLE (LPM), the
regulator also supports RETENTION and AUTO_RM which are currently
unselectable by the driver.
The inspiration of this is taken from [1].
[1] https://source.codeaurora.org/quic/la/kernel/msm-5.4/commit/?h=kernel.lnx.5.4.r1-rel&id=d1220daeffaa440ffff0a8c47322eb0033bf54f5
Signed-off-by: Iskren Chernev <iskren.chernev@gmail.com>
Link: https://lore.kernel.org/r/20220802221112.2280686-6-iskren.chernev@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
If regulator_enable() fails, enable_count is incremented still.
A consumer, assuming no matching regulator_disable() is necessary on
failure, will then get this error message upon regulator_put()
since enable_count is non-zero:
[ 1.277418] WARNING: CPU: 3 PID: 1 at drivers/regulator/core.c:2304 _regulator_put.part.0+0x168/0x170
The consumer could try to fix this in their driver by cleaning up on
error from regulator_enable() (i.e. call regulator_disable()), but that
results in the following since regulator_enable() failed and didn't
increment user_count:
[ 1.258112] unbalanced disables for vreg_l17c
[ 1.262606] WARNING: CPU: 4 PID: 1 at drivers/regulator/core.c:2899 _regulator_disable+0xd4/0x190
Fix this by decrementing enable_count upon failure to enable.
With this in place, just the reason for failure to enable is printed
as expected and developers can focus on the root cause of their issue
instead of thinking their usage of the regulator consumer api is
incorrect. For example, in my case:
[ 1.240426] vreg_l17c: invalid input voltage found
Fixes: 5451781dad ("regulator: core: Only count load for enabled consumers")
Signed-off-by: Andrew Halaney <ahalaney@redhat.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Brian Masney <bmasney@redhat.com>
Link: https://lore.kernel.org/r/20220819194336.382740-1-ahalaney@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Previously, an unresolved regulator supply reference upon calling
regulator_register on an always-on or boot-on regulator caused
set_machine_constraints to be called twice.
This in turn may initialize the regulator twice, leading to voltage
glitches that are timing-dependent. A simple, unrelated configuration
change may be enough to hide this problem, only to be surfaced by
chance.
One such example is the SD-Card voltage regulator in a NanoPI R4S that
would not initialize reliably unless the registration flow was just
complex enough to allow the regulator to properly reset between calls.
Fix this by re-arranging regulator_register, trying resolve the
regulator's supply early enough that set_machine_constraints does not
need to be called twice.
Signed-off-by: Christian Kohlschütter <christian@kohlschutter.com>
Link: https://lore.kernel.org/r/20220818124646.6005-1-christian@kohlschutter.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Matti Vaittinen <mazziesaccount@gmail.com>:
A few* drivers seem to use pattern demonstrated by pseudocode:
- devm_regulator_get()
- regulator_enable()
- devm_add_action_or_reset(regulator_disable())
Introducing devm helpers for this pattern would remove bunch of code from
drivers. Typically following:
- replace 3 calls (devm_regulator_get[_optional](), regulator_enable(),
devm_add_action_or_reset()) with just one
(devm_regulator_get_enable[_optional]()).
- drop disable callback.
- remove stored pointer to struct regulator - which can lead to problem
when an devm action for regulator_disable is used.
I believe this simplifies things by removing some dublicated code.
The suggested managed 'get_enable' APIs do not return the pointer to
regulators for user because any call to regulator_disable()
(or regulator_enable()) may easily lead to regulator enable count imbalance
upon device detach. (Eg, if someone calls regulator_disable() and the
device is then detached before user has re-enabled the regulator). Not
returning the pointer to obtained regulator to caller is a good hint that
the enable/disable should not be manually handled when these APIs are used.
OTOH, not returning the pointer reduces the use-cases by not allowing
the consumers to perform other regulator actions. For example request the
voltages. A few drivers which used the "get, enable,
devm_action_to_disable" did also query the voltages. The API does not suit
needs of such users.
A few regulator consumer drivers seem to be just getting a regulator,
enabling it and registering a devm-action to disable the regulator at
the driver detach and then forget about it.
We can simplify this a bit by adding a devm-helper for this pattern.
Add devm_regulator_get_enable() and devm_regulator_get_enable_optional()
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://lore.kernel.org/r/ed7b8841193bb9749d426f3cb3b199c9460794cd.1660292316.git.mazziesaccount@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The thermal OF code has a new API allowing to migrate the OF
initialization to a simpler approach. The ops are no longer device
tree specific and are the generic ones provided by the core code.
Convert the ops to the thermal_zone_device_ops format and use the new
API to register the thermal zone with these generic ops.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linexp.org>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20220804224349.1926752-31-daniel.lezcano@linexp.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
A couple of small fixes that came in since my pull request, nothing
major here.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmL7fYcACgkQJNaLcl1U
h9DAwgf/SFy3kudCyIA3KVx8FynN133eC+dUt5xNtyNWwWJaJ4NNqZXvRISMup0j
laCTWZ6pFLottgiYM4JoHwbgYvQmtC44jKFKceCVwUNY5mgJXv/bs9w1lgebFzQK
Van7I4s/rTCrYHAg1Jyp9SPi8xTJsDaTd53OB0LUW2CgrI6GJ098LAs+4nArL3fv
PbXueww1F9bcPs57OOow+zan4RZ6IB1CcrOmyl6Yuc9fU/tx4RiCznbCH3Z7mgIv
SJeNxVgaVIlvZ5mVvYPwUItz6QS1RhyJh+L6vZl/uzgrIpt33I8YHlneACz6rlHL
Ld3ISdk0IPSrhbPEtzyq3Y9O3dF8ZA==
=Ix+X
-----END PGP SIGNATURE-----
Merge tag 'regulator-fix-v6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"A couple of small fixes that came in since my pull request, nothing
major here"
* tag 'regulator-fix-v6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: core: Fix missing error return from regulator_bulk_get()
regulator: pca9450: Remove restrictions for regulator-name
The value returned by an i2c driver's remove function is mostly ignored.
(Only an error message is printed if the value is non-zero that the
error is ignored.)
So change the prototype of the remove function to return no value. This
way driver authors are not tempted to assume that passing an error to
the upper layer is a good idea. All drivers are adapted accordingly.
There is no intended change of behaviour, all callbacks were prepared to
return 0 before.
Reviewed-by: Peter Senna Tschudin <peter.senna@gmail.com>
Reviewed-by: Jeremy Kerr <jk@codeconstruct.com.au>
Reviewed-by: Benjamin Mugnier <benjamin.mugnier@foss.st.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Crt Mori <cmo@melexis.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Marek Behún <kabel@kernel.org> # for leds-turris-omnia
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Petr Machata <petrm@nvidia.com> # for mlxsw
Reviewed-by: Maximilian Luz <luzmaximilian@gmail.com> # for surface3_power
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> # for bmc150-accel-i2c + kxcjk-1013
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> # for media/* + staging/media/*
Acked-by: Miguel Ojeda <ojeda@kernel.org> # for auxdisplay/ht16k33 + auxdisplay/lcd2s
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com> # for versaclock5
Reviewed-by: Ajay Gupta <ajayg@nvidia.com> # for ucsi_ccg
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> # for iio
Acked-by: Peter Rosin <peda@axentia.se> # for i2c-mux-*, max9860
Acked-by: Adrien Grassein <adrien.grassein@gmail.com> # for lontium-lt8912b
Reviewed-by: Jean Delvare <jdelvare@suse.de> # for hwmon, i2c-core and i2c/muxes
Acked-by: Corey Minyard <cminyard@mvista.com> # for IPMI
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com> # for drivers/power
Acked-by: Krzysztof Hałasa <khalasa@piap.pl>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Since we don't actually pass the load to the firmware, switch to using
get_optimum_mode() instead of open-coding it.
This is intended to have no effect other than cleanup.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20220726102024.1.Icc838fe7bf0ef54a014ab2fee8af311654f5342a@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
In commit 6eabfc018e ("regulator: core: Allow specifying an initial
load w/ the bulk API") I changed the error handling but had a subtle
that caused us to always return no error even if there was an
error. Fix it.
Fixes: 6eabfc018e ("regulator: core: Allow specifying an initial load w/ the bulk API")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20220809142738.1.I91625242f137c707bb345c51c80c5ecee02eeff3@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
Here is the set of SPDX comment updates for 6.0-rc1.
Nothing huge here, just a number of updated SPDX license tags and
cleanups based on the review of a number of common patterns in GPLv2
boilerplate text. Also included in here are a few other minor updates,
2 USB files, and one Documentation file update to get the SPDX lines
correct.
All of these have been in the linux-next tree for a very long time.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYupz3g8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynPUgCgslaf2ssCgW5IeuXbhla+ZBRAzisAnjVgOvLN
4AKdqbiBNlFbCroQwmeQ
=v1sg
-----END PGP SIGNATURE-----
Merge tag 'spdx-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx
Pull SPDX updates from Greg KH:
"Here is the set of SPDX comment updates for 6.0-rc1.
Nothing huge here, just a number of updated SPDX license tags and
cleanups based on the review of a number of common patterns in GPLv2
boilerplate text.
Also included in here are a few other minor updates, two USB files,
and one Documentation file update to get the SPDX lines correct.
All of these have been in the linux-next tree for a very long time"
* tag 'spdx-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx: (28 commits)
Documentation: samsung-s3c24xx: Add blank line after SPDX directive
x86/crypto: Remove stray comment terminator
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_406.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_398.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_391.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_390.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_385.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_320.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_319.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_318.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_298.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_292.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_179.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_168.RULE (part 2)
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_168.RULE (part 1)
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_160.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_152.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_149.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_147.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_133.RULE
...
Merge series from Douglas Anderson <dianders@chromium.org>:
The main goal of this series is to make a small dent in cleaning up
the way we deal with regulator loads. The idea is to add some extra
functionality to the regulator "bulk" API so that consumers can
specify the load using that.
Drivers tend to want to define the names of their regulators somewhere
in their source file as "static const". This means, inevitable, that
every driver out there open codes something like this:
static const char * const supply_names[] = {
"vcc", "vccl",
};
static int get_regulators(struct my_data *data)
{
int i;
data->supplies = devm_kzalloc(...)
if (!data->supplies)
return -ENOMEM;
for (i = 0; i < ARRAY_SIZE(supply_names); i++)
data->supplies[i].supply = supply_names[i];
return devm_regulator_bulk_get(data->dev,
ARRAY_SIZE(supply_names),
data->supplies);
}
Let's make this more convenient by doing providing a helper that does
the copy.
I have chosen to have the "const" input structure here be the exact
same structure as the normal one passed to
devm_regulator_bulk_get(). This is slightly inefficent since the input
data can't possibly have anything useful for "ret" or consumer and
thus we waste 8 bytes per structure. This seems an OK tradeoff for not
introducing an extra structure.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20220726103631.v2.6.I38fc508a73135a5c1b873851f3553ff2a3a625f5@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
There are a number of drivers that follow a pattern that looks like
this:
1. Use the regulator bulk API to get a bunch of regulators.
2. Set the load on each of the regulators to use whenever the
regulators are enabled.
Let's make this easier by just allowing the drivers to pass the load
in.
As part of this change we need to move the error printing in
regulator_bulk_get() around; let's switch to the new dev_err_probe()
to simplify it.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20220726103631.v2.4.Ie85f68215ada39f502a96dcb8a1f3ad977e3f68a@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
With the following configuration options:
CONFIG_OF is not set
CONFIG_REGULATOR_MT6380=y
we get the following build warning:
CC drivers/regulator/mt6380-regulator.o
drivers/regulator/mt6380-regulator.c:322:34: warning: ‘mt6380_of_match’ defined but not used [-Wunused-const-variable=]
Fix this by annotating that array with __maybe_unused, as done in
various regulator drivers.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/all/202207240252.ZY5hSCNB-lkp@intel.com/
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Chenglin Xu <chenglin.xu@mediatek.com>
Link: https://lore.kernel.org/r/20220727132637.76d6073f@endymion.delvare
Signed-off-by: Mark Brown <broonie@kernel.org>
Regulators marked with "regulator-always-on" or "regulator-boot-on"
as well as an "off-on-delay-us", may run into cycling issues that are
hard to detect.
This is caused by the "last_off" state not being initialized in this
case.
Fix the "last_off" initialization by setting it to the current kernel
time upon initialization, regardless of always_on/boot_on state.
Signed-off-by: Christian Kohlschütter <christian@kohlschutter.com>
Link: https://lore.kernel.org/r/FAFD5B39-E9C4-47C7-ACF1-2A04CD59758D@kohlschutter.com
Signed-off-by: Mark Brown <broonie@kernel.org>
We should call the of_node_put() for the reference returned by
of_get_child_by_name() which has increased the refcount.
Fixes: 40e20d68bb ("regulator: of: Add support for parsing regulator_state for suspend state")
Signed-off-by: Liang He <windhl@126.com>
Link: https://lore.kernel.org/r/20220715111027.391032-1-windhl@126.com
Signed-off-by: Mark Brown <broonie@kernel.org>
PMP8074 is a companion PMIC for the Qualcomm IPQ8074 WiSoC-s.
It features 5 HF-SMPS and 13 LDO regulators.
HF-SMPS regulators are Buck HFS430 regulators.
L1, L2 and L3 are HT_N1200_ST subtype LDO regulators.
L4 is HT_N300_ST subtype LDO regulator.
L5 and L6 are HT_P600 subtype LDO regulators.
L7, L11, L12 and L13 are HT_P150 subtype LDO regulators.
L10 is HT_P50 subtype LDO regulator.
This commit adds support for all of the buck regulators and LDO-s except
for L10 as I dont have documentation on its output voltage range.
S3 is the CPU cluster voltage supply, S4 supplies the UBI32 NPU cores
and L11 is the SDIO/eMMC I/O voltage regulator required for high speeds.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Link: https://lore.kernel.org/r/20220704212402.1715182-7-robimarko@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
HT_P600 is a LDO PMOS regulator based on LV P600 using HFS430 layout
found in PMP8074 and PMS405 PMIC-s.
Both PMP8074 and PMS405 define the programmable range as 1.704 to 1.896V
but the actual MAX output voltage depends on the exact LDO in each of
the PMIC-s.
Their usual voltage that they are used is 1.8V.
It has a max current of 600mA, voltage step of 8mV.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Link: https://lore.kernel.org/r/20220704212402.1715182-5-robimarko@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
HT_P150 is a LDO PMOS regulator based on LV P150 using HFS430 layout
found in PMP8074 and PMS405 PMIC-s.
Both PMP8074 and PMS405 define the programmable range as 1.616V to 3.304V
but the actual MAX output voltage depends on the exact LDO in each of
the PMIC-s.
It has a max current of 150mA, voltage step of 8mV.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Link: https://lore.kernel.org/r/20220704212402.1715182-4-robimarko@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The patch makes sense but these are not compile warnings.
They come from scripts/checkversion.pl, which can be called
by 'make versioncheck', so I suppose that something in your
build system is running 'make versioncheck'.
Eliminate the follow versioncheck warning:
./drivers/regulator/max597x-regulator.c: 21 linux/version.h not needed.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Link: https://lore.kernel.org/r/20220711034011.46096-1-jiapeng.chong@linux.alibaba.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Drivers should depend on rather than select their MFDs.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20220707111753.16581-1-broonie@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Use Complete data type declaration of 'sel' in ti_abb_set_voltage_sel().
Fix spelling of 'are'nt' in comments.
Signed-off-by: Zhang Jiaming <jiaming@nfschina.com>
Link: https://lore.kernel.org/r/20220705071445.21124-1-jiaming@nfschina.com
Signed-off-by: Mark Brown <broonie@kernel.org>
max597x is hot swap controller.
This regulator driver controls the same & also configures fault
protection features supported by the chip.
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Signed-off-by: Marcello Sylvester Bauer <sylv@sylv.io>
Signed-off-by: Naresh Solanki <Naresh.Solanki@9elements.com>
Link: https://lore.kernel.org/r/20220705122244.472894-4-Naresh.Solanki@9elements.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Stephan Gerhold <stephan.gerhold@kernkonzept.com>:
Fix the voltage range for the pm8916_pldo in the qcom_smd-regulator
driver and add definitions for the regulators available in PM8909.
In scmi_regulator_probe(), of_find_node_by_name() will decrease
the refcount of its first argument and we need a of_node_get()
to keep reference balance.
Signed-off-by: Liang He <windhl@126.com>
Reviewed-by: Cristian Marussi <cristian.marussi@arm.com>
Link: https://lore.kernel.org/r/20220622034816.4094043-1-windhl@126.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The set of regulators available in the PM8909 PMIC is similar to PM8916
which is already supported by the driver. s3, s4 and l16 are missing.
However, probing the SPMI hardware identification registers using the
qcom_spmi-regulator driver reveals that the regulators in PM8909 are
actually some kind of mixture between PM8916 and PM8226:
- ult_lo_smps (= pm8916_buck_lvo_smps): s1
- ult_ho_smps (= pm8916_buck_hvo_smps): s2
- ult_nldo (= pm8916_nldo): l1, l2, l3, l10
- ult_pldo (= pm8916_pldo): l4, l8, l9, l12-l15, l17, l18
- pldo (= pm8226_pldo): l5, l6, l7, l11
Use this mapping to add the rpm_regulator_data for PM8909 by reusing
the existing regulator definitions.
Signed-off-by: Stephan Gerhold <stephan.gerhold@kernkonzept.com>
Link: https://lore.kernel.org/r/20220623094614.1410180-4-stephan.gerhold@kernkonzept.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The PM8916 device specification [1] documents a programmable range of
1.75V to 3.337V with 12.5mV steps for the PMOS LDOs in PM8916. This
range is also used when controlling the regulator directly using the
qcom_spmi-regulator driver ("ult_pldo" there).
However, for some reason the qcom_smd-regulator driver allows a much
larger range for the same hardware component. This could be simply a
typo, since the start of the range is essentially just missing a '1'.
In practice this does not cause any major problems, since the driver
just sends the actual voltage to the RPM firmware instead of making use
of the incorrect voltage selector. Still, having the wrong range there
is confusing and prevents the regulator core from validating requests
correctly.
[1]: https://developer.qualcomm.com/download/sd410/pm8916pm8916-1-power-management-ic-device-specification.pdf
Fixes: 57d6567680 ("regulator: qcom-smd: Add PM8916 support")
Signed-off-by: Stephan Gerhold <stephan.gerhold@kernkonzept.com>
Link: https://lore.kernel.org/r/20220623094614.1410180-2-stephan.gerhold@kernkonzept.com
Signed-off-by: Mark Brown <broonie@kernel.org>
'platform_device_id' struct is defined in 'mod_devicetable.h'.
Even 'of.h' also includes this header usage. The 'of.h' cannot be removed
due to 'of_match_ptr' function.
Signed-off-by: ChiYuan Huang <cy_huang@richtek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/1656466861-7737-2-git-send-email-u0084500@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
From the common binding, 'enable-gpio' or 'enable-gpios' are all well
for external 'enable' gpio.
'gpiod_get_from_of_node' only parse the 'enable' property, it need to
add the gpio suffix. It's more convenient to use fwnode_gpiod_get_index.
Although fwnode parsing is not preferred, but 'of_parse_cb' already can
guarantee the callback will only be used by regulator of_node parsing.
Signed-off-by: ChiYuan Huang <cy_huang@richtek.com>
Link: https://lore.kernel.org/r/1656466861-7737-1-git-send-email-u0084500@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add RT5120 PMIC regulator support.
It integrates 4 buck convertes, 1 LDO voltage regulator, 1 external
enable signal to control the external power source.
Signed-off-by: ChiYuan Huang <cy_huang@richtek.com>
Link: https://lore.kernel.org/r/1655892104-10874-4-git-send-email-u0084500@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
backlight_properties.fb_blank is deprecated. The states it represents
are handled by other properties; but instead of accessing those
properties directly, drivers should use the helpers provided by
backlight.h.
Instead of retrieving the backlight brightness in struct
backlight_properties manually, and then checking whether the backlight
should be on at all, use backlight_get_brightness() which does all
this and insulates this from future changes.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20220607185304.1128962-1-steve@sk2.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Based on the normalized pattern:
this program is free software you can redistribute it and/or modify it
under the terms of the gnu general public license version 2 as
published by the free software foundation this program is distributed
as is without any warranty of any kind whether express or implied
without even the implied warranty of merchantability or fitness for a
particular purpose see the gnu general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference.
Reviewed-by: Allison Randal <allison@lohutok.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on the normalized pattern:
this program is free software you can redistribute it and/or modify it
under the terms of the gnu general public license version 2 as
published by the free software foundation this program is distributed
as is without any warranty of any kind whether expressed or implied
without even the implied warranty of merchantability or fitness for a
particular purpose see the gnu general public license version 2 for
more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference.
Reviewed-by: Allison Randal <allison@lohutok.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on the normalized pattern:
this program is free software you can redistribute it and/or modify it
under the terms of the gnu general public license as published by the
free software foundation version 2 this program is distributed as is
without any warranty of any kind whether express or implied without
even the implied warranty of merchantability or fitness for a
particular purpose see the gnu general public license for more details
you should have received a copy of the gnu general public license
along with this program if not write to the free software foundation
inc 59 temple place suite 330 boston ma 02111-1307 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference.
Reviewed-by: Allison Randal <allison@lohutok.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on the normalized pattern:
this program is free software you can redistribute it and/or modify it
under the terms of the gnu general public license as published by the
free software foundation version 2 this program is distributed as is
without any warranty of any kind whether express or implied without
even the implied warranty of merchantability or fitness for a
particular purpose see the gnu general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference.
Reviewed-by: Allison Randal <allison@lohutok.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cros_ec_command() is the name of a function as well as a struct, as such
it can confuse indexing tools (like ctags). Avoid this by renaming it to
cros_ec_cmd(). Update all the callsites to use the new name.
This patch is a find-and-replace, so should not introduce any functional
changes.
Suggested-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Tzung-Bi Shih <tzungbi@kernel.org>
Link: https://lore.kernel.org/r/20220606201825.763788-3-pmalani@chromium.org
Reduce code duplication by using the common cros_ec_command() function
instead of the locally defined variant.
Cc: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Tzung-Bi Shih <tzungbi@kernel.org>
Link: https://lore.kernel.org/r/20220606201825.763788-2-pmalani@chromium.org
If the node for the match name cannot be found, 'of_regulator_match' will
returns init_data as NULL for this regulator.
Add the check for the init_data. If it's NULL, make 'rt5190a_of_parse_cb'
function directly return.
Signed-off-by: ChiYuan Huang <cy_huang@richtek.com>
Link: https://lore.kernel.org/r/1654148646-12182-1-git-send-email-u0084500@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
MP5496 is the updated version of MP5416 with the only difference being
that now all Buck regulators have the same 0.6-2.1875V range with a 12.5mV
step.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Acked-by: Saravanan Sekar <sravanhome@gmail.com>
Link: https://lore.kernel.org/r/20220604145816.47576-4-robimarko@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In preparation for adding support for MP5496 which slightly differs from
MP5416 convert the driver to use OF match data instead of always using the
MP5416 regulator_desc for regulator registration.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Acked-by: Saravanan Sekar <sravanhome@gmail.com>
Link: https://lore.kernel.org/r/20220604145816.47576-3-robimarko@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use devm_register_sys_off_handler() that replaces global
pm_power_off_prepare variable and allows to register multiple
power-off handlers.
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
of_find_node_by_name() returns a node pointer with refcount
incremented, we should use of_node_put() on it when done.
Add missing of_node_put() to avoid refcount leak.
Fixes: 0fbeae70ee ("regulator: add SCMI driver")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: https://lore.kernel.org/r/20220516074433.32433-1-linmq006@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
of_node_get() returns a node with refcount incremented.
Calling of_node_put() to drop the reference when not needed anymore.
Fixes: 3784b6d64d ("regulator: pfuze100: add pfuze100 regulator driver")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: https://lore.kernel.org/r/20220511113506.45185-1-linmq006@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Following changes have been made:
- S5, L4, L18, L20 and L21 were removed (S5 is managed by
SPMI, whereas the rest seems not to exist [or at least it's blocked
by Sony Loire /MSM8956/ RPM firmware])
- Supply maps have were adjusted to reflect regulator changes.
Fixes: e44adca5fa ("regulator: qcom_smd: Add PM8950 regulators")
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Link: https://lore.kernel.org/r/20220430163753.609909-1-konrad.dybcio@somainline.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Since the introduction of regulator->enable_count, a driver that did
an exclusive get on an already-enabled regulator would end up with
enable_count initialized to 0 but rdev->use_count initialized to 1.
With that starting point the regulator is effectively stuck enabled,
because if the driver attempted to disable it it would fail the
enable_count underflow check in _regulator_handle_consumer_disable().
The EXCLUSIVE_GET path in _regulator_get() now initializes
enable_count along with rdev->use_count so that the regulator can be
disabled without underflowing the former.
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Fixes: 5451781dad ("regulator: core: Only count load for enabled consumers")
Link: https://lore.kernel.org/r/20220505043152.12933-1-zev@bewilderbeest.net
Signed-off-by: Mark Brown <broonie@kernel.org>
If a regulator provides a get_error_flags() operation, its sysfs
attributes will now include an entry for each defined
REGULATOR_ERROR_* flag.
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Link: https://lore.kernel.org/r/20220504065252.6955-3-zev@bewilderbeest.net
Signed-off-by: Mark Brown <broonie@kernel.org>
When DVS is enabled via the devicetree properties
"nxp,dvs-run-voltage" and "nxp,dvs-standby-voltage" then
also the bit that enables DVS control via PMIC_STBY_REQ pin
should be set.
Signed-off-by: Rickard x Andersson <rickaran@axis.com>
Link: https://lore.kernel.org/r/20220429072211.24957-5-rickaran@axis.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The default configuration of the PMIC behavior makes the PMIC
power cycle most regulators on WDOG_B assertion. This power
cycling causes the memory contents of OCRAM to be lost.
Some systems neeeds some memory that survives reset and
reboot, therefore this patch is created.
Signed-off-by: Rickard x Andersson <rickaran@axis.com>
Link: https://lore.kernel.org/r/20220429072211.24957-4-rickaran@axis.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Make the I2C Level Translator included in PCA9450 configurable from
devicetree. The reset state is off. By setting nxp,i2c-lt-enable, the
I2C Level Translator will be enabled while in STANDBY or RUN state.
Signed-off-by: Per-Daniel Olsson <perdo@axis.com>
Signed-off-by: Rickard x Andersson <rickaran@axis.com>
Link: https://lore.kernel.org/r/20220429072211.24957-2-rickaran@axis.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Regulators block of SM5703 controls several voltage regulators which
are used to power various components. There are 3 LDO outputs ranging
from 1.5 to 3.3V, a buck regulator ranging from 1V to 3V, two fixed
voltage LDO regulators for powering the USB devices and one high-power
fixed voltage LDO line (actually two lines) meant to power high-power
USB devices.
Signed-off-by: Markuss Broks <markuss.broks@gmail.com>
Link: https://lore.kernel.org/r/20220423085319.483524-6-markuss.broks@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Having one enable-gpios property for all regulators is discouraged and
instead, similarly to regulator core ena_gpiod feature, each GPIO should
be present in each regulator node. Add support for parsing such GPIOs,
keeping backwards compatibility.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Tested-by: ChiYuan Huang <cy_huang@richtek.com>
Link: https://lore.kernel.org/r/20220425072455.27356-3-krzysztof.kozlowski@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
These delays can be relatively large (e.g., hundreds of microseconds to
several milliseconds on RK3399 Gru systems). Per
Documentation/timers/timers-howto.rst, that should usually use a
sleeping delay. Let's use the existing regulator delay helper to handle
both large and small delays appropriately. This avoids burning a bunch
of CPU time and hurting scheduling latencies when hitting regulators a
lot (e.g., during cpufreq).
The sleep vs. delay issue choice has been made differently over time --
early versions of RK3399 Gru PWM-regulator support used usleep_range()
in pwm-regulator.c. More of this got moved into the regulator core,
in commits like:
73e705bf81 regulator: core: Add set_voltage_time op
At the same time, the sleep turned into a delay.
It's OK to sleep in _regulator_do_set_voltage(), as we aren't in an
atomic context. (All our callers grab various mutexes already.)
I avoid using fsleep() because it uses a usleep_range() of [N to N*2],
and usleep_range() very commonly biases to the high end of the range. We
don't want to double the expected delay, especially for long delays.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/20220420141511.v2.2.If0fc61a894f537b052ca41572aff098cf8e7e673@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
KASAN report slab-out-of-bounds in __regmap_init as follows:
BUG: KASAN: slab-out-of-bounds in __regmap_init drivers/base/regmap/regmap.c:841
Read of size 1 at addr ffff88803678cdf1 by task xrun/9137
CPU: 0 PID: 9137 Comm: xrun Tainted: G W 5.18.0-rc2
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-1ubuntu1.1 04/01/2014
Call Trace:
<TASK>
dump_stack_lvl+0xe8/0x15a lib/dump_stack.c:88
print_report.cold+0xcd/0x69b mm/kasan/report.c:313
kasan_report+0x8e/0xc0 mm/kasan/report.c:491
__regmap_init+0x4540/0x4ba0 drivers/base/regmap/regmap.c:841
__devm_regmap_init+0x7a/0x100 drivers/base/regmap/regmap.c:1266
__devm_regmap_init_i2c+0x65/0x80 drivers/base/regmap/regmap-i2c.c:394
da9121_i2c_probe+0x386/0x6d1 drivers/regulator/da9121-regulator.c:1039
i2c_device_probe+0x959/0xac0 drivers/i2c/i2c-core-base.c:563
This happend when da9121 device is probe by da9121_i2c_id, but with
invalid dts. Thus, chip->subvariant_id is set to -EINVAL, and later
da9121_assign_chip_model() will access 'regmap' without init it.
Fix it by return -EINVAL from da9121_assign_chip_model() if
'chip->subvariant_id' is invalid.
Fixes: f3fbd5566f ("regulator: da9121: Add device variants")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Adam Ward <Adam.Ward.Opensource@diasemi.com>
Link: https://lore.kernel.org/r/20220421090335.1876149-1-weiyongjun1@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
