* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6:
[S390] dasd: tunable missing interrupt handler
[S390] dasd: allocate fallback cqr for reserve/release
[S390] topology: use default MC domain initializer
[S390] initrd: change default load address
[S390] cmm, smsgiucv_app: convert sender to uppercase
[S390] cmm: add missing __init/__exit annotations
[S390] cio: use all available paths for some internal I/O
[S390] ccwreq: add ability to use all paths
[S390] cio: ccw_device_online_store return -EINVAL in case of missing driver
[S390] cio: Log the response from the unit check handler
[S390] cio: CHSC SIOSL Support
UART Features extract from STEricsson U6715 data-sheet (arm926 SoC for mobile phone):
* Fully compatible with industry standard 16C550 and 16C450 from various
manufacturers
* RX and TX 64 byte FIFO reduces CPU interrupts
* Full double buffering
* Modem control signals include CTS, RTS, (and DSR, DTR on UART1 only)
* Automatic baud rate selection
* Manual or automatic RTS/CTS smart hardware flow control
* Programmable serial characteristics:
– Baud rate generation (50 to 3.25M baud)
– 5, 6, 7 or 8-bit characters
– Even, odd or no-parity bit generation and detection
– 1, 1.5 or 2 stop bit generation
* Independent control of transmit, receive, line status, data set interrupts and FIFOs
* Full status-reporting capabilities
* Separate DMA signaling for RX and TX
* Timed interrupt to spread receive interrupt on known duration
* DMA time-out interrupt to allow detection of end of reception
* Carkit pulse coding and decoding compliant with USB carkit control interface [40]
In 16550A auto-configuration, if the fifo size is 64 then it's an U6 16550A port
Add set_termios hook & export serial8250_do_set_termios to change uart
clock following baudrate
Signed-off-by: Philippe Langlais <philippe.langlais@stericsson.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Sorry, one more fix, this one depends on the other, so this is rather 2/2.
--
tty->driver_data is used all over the code, but never set. This
results in oopses like:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000130
IP: [<ffffffff814a0040>] mutex_lock+0x10/0x40
...
Pid: 2157, comm: modem-manager Not tainted 2.6.34.1-0.1-desktop #1 2768DR7/2768DR7
RIP: 0010:[<ffffffff814a0040>] [<ffffffff814a0040>] mutex_lock+0x10/0x40
RSP: 0018:ffff88007b16fa50 EFLAGS: 00010286
RAX: 0000000000000000 RBX: 0000000000000130 RCX: 0000000000000003
RDX: 0000000000000003 RSI: 0000000000000286 RDI: 0000000000000130
RBP: 0000000000001000 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000001 R11: 0000000000000000 R12: 0000000000000130
R13: 0000000000000001 R14: 0000000000000000 R15: ffff88007b16feb4
...
Call Trace:
[<ffffffffa077690d>] ntty_write_room+0x4d/0x90 [nozomi]
...
Set tty->driver_data to the computed port in .install to not recompute it in
every place where needed. Switch .open to use driver_data too.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Alan Cox <alan@linux.intel.com>
Cc: stable <stable@kernel.org> [.34, .35]
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently ntty_install omits to increment tty count and we get the
following warnings:
Warning: dev (noz2) tty->count(0) != #fd's(1) in tty_open
So to fix that, add one tty->count++ there.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Alan Cox <alan@linux.intel.com>
Cc: stable <stable@kernel.org> [.34, .35]
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Because of the way gpiolib works we actually need to ifdef this in our
header file
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Also add check for dma controller or the uart ports.
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Major changes are:
* refine the comments in the driver
* remove unused member from structure "hsu_port"
* extended spin_lock protoction for dma mode in port_irq()
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A general problem for uart rx dma channel is you never know when
and how much data will be received, so usually preset it a DMA
descriptor with a big size, and rely on DMA RX timeout IRQ to
know there is some data in rx channel.
For a RX data size of multiple of MOTSR, there will be no timeout
IRQ issued, thus OS will never be notified about that.
This is a work around for that, current timer frequency is 5 times
per second, it should vary according to the baud rate
When future silicon version fix the problem, this workaround need
be removed
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a PCI & UART driver, which suppors both PIO and DMA mode
UART operation. It has 3 identical UART ports and one internal
DMA controller.
Current FW will export 4 pci devices for hsu: 3 uart ports and 1
dma controller, each has one IRQ line. And we need to discuss the
device model, one PCI device covering whole HSU should be a better
model, but there is a problem of how to export the 4 IRQs info
Current driver set the highest baud rate to 2746800bps, which is
easy to scale down to 115200/230400.... To suport higher baud rate,
we need add special process, change DLAB/DLH/PS/DIV/MUL registers
all together.
921600 is the highest baud rate that has been tested with Bluetooth
modem connected to HSU port 0. Will test more when there is right
BT firmware.
Current version contains several work around for A0's Silicon bugs
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
mxser_transmit_chars(tty, port) is called only from mxser_interrupt().
NULL check is performed in mxser_interrupt() so it is redundant here.
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Acked-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
(ALMA_ANS | DRAGONIXVZ | M68EZ328ADS) doesn't exist in Kconfig, therefore
remove all references to it from the source code.
Signed-off-by: Christoph Egger <siccegge@cs.fau.de>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Move the probe and remove functions to the devinit and devexit sections.
Signed-off-by: Richard Röjfors <richard.rojfors@pelagicore.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Don't take the port spinlock in uart functions where the serial core
already takes care of locking/unlocking them.
The code would actually lock up on architectures where spinlocks are
implemented.
Also protect calling mcf_rx_chars/mcf_tx_chars in the interrupt handler by
the port spinlock and use IRQ_RETVAL to return from isr.
[akpm@linux-foundation.org: make irq-handler return value more explicit]
Signed-off-by: Yury Georgievskiy <ygeorgie@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix several issues related to the RS485 interface:
- It adds the flag SER_RS485_RTS_BEFORE_SEND that was missing from the
serial_rs485 structure (even if "delay_rts_before_send" was existing)
- It adds a further "delay_rts_after_send" field for those drivers that
can have a delay after send (e.g., atmel_serial)
- It fixes the usage of the structure in the atmel_serial driver (where
"delay_rts_before_send" should be used instead of "delay_rts_after_send").
Signed-off-by: Claudio Scordino <claudio@evidence.eu.com>
Signed-off-by: Bernhard Roth <br@pwrnet.de>
Cc: Philippe De Muyter <phdm@macqel.be>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ERROR: code indent should use tabs where possible
#32: FILE: drivers/serial/altera_uart.c:397:
+^I ALTERA_UART_STATUS_TRDY_MSK))$
total: 1 errors, 0 warnings, 39 lines checked
./patches/altera_uart-simplify-altera_uart_console_putc.patch has style problems, please review. If any of these errors
are false positives report them to the maintainer, see
CHECKPATCH in MAINTAINERS.
Please run checkpatch prior to sending patches
This fix got lost when someone merged "altera_uart: simplify
altera_uart_console_putc()". Please don't lose fixes. Please don't write
of mere patches which have trivial checkpatch errors.
Cc: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
At the moment there is only one platform type supported and there is is
hard wired, but with these changes the infrastructure is now there for
anyone else to provide methods for their hardware.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This device is used by some of the Intel MID platforms. It's not similar
enough to the MAX3100 to use the same driver.
At this point the driver is specific to the platform and not generalised.
We will fix that later.
Signed-off-by: jianwei.yang <jianwei.yang@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When the console has been redirected, a hangup of the tty
will cause tty_release to be called under the big tty_mutex,
which leads to a deadlock because hangup is also called
under the BTM.
This moves the BTM deeper into the tty_hangup function so
we can close the redirected tty without holding the BTM.
In case of pty, we now need to drop the BTM before
calling tty_vhangup.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: John Kacur <jkacur@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The ldisc number now gets passed into ->set_ldisc.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Most tty drivers may block while opening a device.
Since this possibly depends on another thread
closing it first and both threads may need the BTM,
we need to release it here.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The tty locking now follows the rules for mutexes, so
we can replace the BKL usage with a new subsystem
wide mutex.
Using a regular mutex here will change the behaviour
when blocked on the BTM from spinning to sleeping,
but that should not be visible to the user.
Using the mutex also means that all the BTM is now
covered by lockdep.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This changes all remaining users of tty_lock_nested
to be non-recursive, which lets us kill this function.
As a consequence, we won't need to keep the lock count
any more, which allows more simplifications later.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some wait_until_sent versions require the big
tty mutex, others don't and some callers of
wait_until_sent already hold it while other don't.
That leads to recursive use of the BTM in these
functions, which we're trying to get rid of.
This turns all cleans up the locking there so
that the driver's wait_until_sent function
never takes the BTM itself if it is already
called with that lock held.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We need to release the BTM in paste_selection() when
sleeping in tty_ldisc_ref_wait to avoid deadlocks
with tty_ldisc_enable.
In tty_set_ldisc, we now always grab the BTM before
taking the ldisc_mutex in order to avoid AB-BA
deadlocks between the two.
tty_ldisc_halt potentially blocks on a workqueue
function that takes the BTM, so we must release
the BTM before calling it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Calling wait_event_interruptible implicitly
releases the BKL when it sleeps, but we need
to do this explcitly when we have converted
it to a mutex.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The wait_event_interruptible_timeout in acm_port_down is
never reached. Remove it to avoid possible deadlocks
with the big tty mutex if someone were to start using
the blocking version of acm_port_down.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
vgacon_do_font_op releases and reacquires the BTM while holding
console_sem. This violates the rule that BTM has to be the
outer lock whenever we hold both.
There does not seem to be any reason to give up the BTM here,
so just stop doing that.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
tty_mutex is never taken with the BTM held, except for
two corner cases that are worked around here.
We give up the BTM before calling tty_release() in the
error path of tty_open().
Similarly, we reorder the locking in ptmx_open()
to get tty_mutex before the BTM.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As a preparation for replacing the big kernel lock
in the TTY layer, wrap all the callers in new
macros tty_lock, tty_lock_nested and tty_unlock.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Move termios initialization in open into uart_dtr_rts to make sure
it always gets called when necessary. Based on a suggestion from
Alan Cox.
Alan writes:
Ok this sort of makes sense. Something isn't getting initialised and both
getty and minicom will do a termios set which is sorting it out.
This is occurring because the generic block_til_ready sets
ASYNCB_NORMAL_ACTIVE so the termios updating gets skipped.
This patch should cure it and then we can think about doing it more
elegantly by getting the serial layer to use tty_port_open, kfifo and
the like and removing the tons of repeated crap in all the drivers.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reported-by: Tony Luck <tony.luck@intel.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Tony Luck <tony.luck@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Our code now rather closely resembles the helper, so switch to it.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The port mutex protects port->tty, but these paths never need to walk from
port->tty. They do need the low level lock as the API expects that but they
already also take it.
Thus we can drop the extra mutex lock calls here.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We can make this the same as the ones that will be needed by the tty_port
helper logic that we want to move to but still call them from the existing
code base.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We want to push the lock/unlock into the helper functions so that we
can prepare to move to using the tty_port helper. The expansion initially
comes out a bit ugly but its worth the temporary expansion IMHO just so
we can produce a nice testable series of changes.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This takes all the tty references through the expected interface points so
we can refcount them.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The vt layer isn't safely handling reference counts to tty object on the input
side. Add a tty port structure to the vt layer in order to implement this using
the standard helpers.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The virtual console layer uses the BKL for various things that don't really
need it. Clean them out.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Pass down the ldisc number so that the drivers don't have to peek into the
tty object themselves. This lets us get rid of another case of back referencing
port to tty which we don't want (because of races versus hangup/close).
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
One or two drivers go poking back into the tty from the termios setting
routine in unsafe ways. We don't need to pass the tty down because the
[ab]users are just using it to get at things they can get at anyway.
This leaves low_latency setting to sort out along with set_ldisc use.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make it robust against hang up events. In most cases we can do this simply
by passing the right things in the first place.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use the port mutex and port lock to fix the various races. The locking
still isn't totally consistent but its better than before. Wants switching
to the port helpers.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This now refcounts but doesn't actually check the reference was obtained in
all the places it should.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use the port mutex instead
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The lock is no longer needed for wait until sent paths so this can go
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use the port mutext for config setting, the rest is locked sufficiently
anyway that the BKL makes no odds.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We don't need it while waiting and we can lock the ioctls using the port
mutex. While at it eliminate use of the hangup mutex and switch to the port
mutex.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We can use the port mutex for this and also for the hangup path so removing
the problematic use of the hangup mutex in this driver. Fix up the locking
on the various port flags while we are at it.
Ultimately this driver needs to be using tty_port_ helpers which would sort
this out far better.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As with the others we can use the port mutex to get the needed locking
properties and fix the race with open.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The riscom8 board uses lock_kernel to protect bits of the port setting
ioctl logic. We can use the port mutex for this as the logic is internal
and will also lock set versus open (a locking property that has been lost
somewhere along the way)
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This lets us avoid problems with races on the flag changes
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove unneeded tty layer lock kernel bits. Relock the needed bits using the
port mutex. The istallion still has brd state races but those are not new
or introduced by the removal of the lock_kernel logic.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jesse's initial patch commit said:
"At panic time (i.e. when oops_in_progress is set) we should try a bit
harder to update the screen and make sure output gets to the VT, since
some drivers are capable of flipping back to it.
So make sure we try to unblank and update the display if called from a
panic context."
I've enhanced this to add a flag to the vc that console layer can set to
indicate they want this behaviour to occur. This also adds support to
fbcon for that flag and adds an fb flag for drivers to indicate they want
to use the support. It enables this for KMS drivers.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Acked-by: James Simmons <jsimmons@infradead.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch is against the 2.6.34 source.
Paraphrased from the 1989 BSD patch by David Borman @ cray.com:
These are the changes needed for the kernel to support
LINEMODE in the server.
There is a new bit in the termios local flag word, EXTPROC.
When this bit is set, several aspects of the terminal driver
are disabled. Input line editing, character echo, and mapping
of signals are all disabled. This allows the telnetd to turn
off these functions when in linemode, but still keep track of
what state the user wants the terminal to be in.
New ioctl:
TIOCSIG Generate a signal to processes in the
current process group of the pty.
There is a new mode for packet driver, the TIOCPKT_IOCTL bit.
When packet mode is turned on in the pty, and the EXTPROC bit
is set, then whenever the state of the pty is changed, the
next read on the master side of the pty will have the TIOCPKT_IOCTL
bit set. This allows the process on the server side of the pty
to know when the state of the terminal has changed; it can then
issue the appropriate ioctl to retrieve the new state.
Since the original BSD patches accompanied the source code for telnet
I've left that reference here, but obviously the feature is useful for
any remote terminal protocol, including ssh.
The corresponding feature has existed in the BSD tty driver since 1989.
For historical reference, a good copy of the relevant files can be found
here:
http://anonsvn.mit.edu/viewvc/krb5/trunk/src/appl/telnet/?pathrev=17741
Signed-off-by: Howard Chu <hyc@symas.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The mrst_max3110 driver had a set of unsafe wakeup sequences
along the following line:
if (!atomic_read(&foo)) {
atomic_set(&foo, 1);
wake_up(worker_thread);
}
and the worker thread would do
if (atomic_read(&foo)) {
do_work();
atomic_set(&foo, 0);
}
which can result in various missed wakups due to test-then-set races,
as well as due to clear-after-work instead of clear-before-work.
This patch fixes these races by using the proper bit test-and-set operations,
and by doing clear-before-work.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The mrst_max3110.c driver uses an open coded, non atomic variable
to create exclusion between two of its worker threads. More than that,
while the main thread does a proper set-work-clear sequence,
the other thread only does a test, with the result that no actual
exclusion is happening.
this patch replaces this open coded variable with a proper mutex
in addition, the 'lock' spinlock is removed from the per adapter structure,
the lock was only ever initialized but never used
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
MAX3111 is the SPI/UART IC installed on the MRST SPI Port Card as a serial
debug goal, and the SPI Port Card will be frequently mounted and unmounted
from the main board by developers depending whether debug serial is
required or not.
As the MAX3111 has no subvendor or product id registers available, the patch
will try to access one register to decide if this IC is present or not.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This driver enable the max3110 device, it can be used as
a system console. the IRQ needs be enabled if user want a
better performance. MRST max3110 works in 3.684MHz clock,
which supports 230400 as its maximum rate.
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Adding UART_CAP_EFR and UART_CAP_SLEEP flags will enable sleep mode
and automatic CTS flow control for 16C950 UARTs. It will also avoid
capabilities detection warning like this:
"ttyS0: detected caps 00000700 should be 00000100"
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
as there's no config CONSOLE (never has been as far as I can tell) and
noone has ever missed that piece of code, it should be safe to remove
it making the kernel a tiny bit less complex.
Signed-off-by: Christoph Egger <siccegge@cs.fau.de>
Acked-by: Greg Ungerer <gerg@snapgear.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/char/n_gsm.c: linux/timer.h is included more than once.
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.infradead.org/mtd-2.6: (79 commits)
mtd: Remove obsolete <mtd/compatmac.h> include
mtd: Update copyright notices
jffs2: Update copyright notices
mtd-physmap: add support users can assign the probe type in board files
mtd: remove redwood map driver
mxc_nand: Add v3 (i.MX51) Support
mxc_nand: support 8bit ecc
mxc_nand: fix correct_data function
mxc_nand: add V1_V2 namespace to registers
mxc_nand: factor out a check_int function
mxc_nand: make some internally used functions overwriteable
mxc_nand: rework get_dev_status
mxc_nand: remove 0xe00 offset from registers
mtd: denali: Add multi connected NAND support
mtd: denali: Remove set_ecc_config function
mtd: denali: Remove unuseful code in get_xx_nand_para functions
mtd: denali: Remove device_info_tag structure
mtd: m25p80: add support for the Winbond W25Q32 SPI flash chip
mtd: m25p80: add support for the Intel/Numonyx {16,32,64}0S33B SPI flash chips
mtd: m25p80: add support for the EON EN25P{32, 64} SPI flash chips
...
Fix up trivial conflicts in drivers/mtd/maps/{Kconfig,redwood.c} due to
redwood driver removal.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6: (96 commits)
no need for list_for_each_entry_safe()/resetting with superblock list
Fix sget() race with failing mount
vfs: don't hold s_umount over close_bdev_exclusive() call
sysv: do not mark superblock dirty on remount
sysv: do not mark superblock dirty on mount
btrfs: remove junk sb_dirt change
BFS: clean up the superblock usage
AFFS: wait for sb synchronization when needed
AFFS: clean up dirty flag usage
cifs: truncate fallout
mbcache: fix shrinker function return value
mbcache: Remove unused features
add f_flags to struct statfs(64)
pass a struct path to vfs_statfs
update VFS documentation for method changes.
All filesystems that need invalidate_inode_buffers() are doing that explicitly
convert remaining ->clear_inode() to ->evict_inode()
Make ->drop_inode() just return whether inode needs to be dropped
fs/inode.c:clear_inode() is gone
fs/inode.c:evict() doesn't care about delete vs. non-delete paths now
...
Fix up trivial conflicts in fs/nilfs2/super.c
This patch adds USB Vendor and Product ID for Pelican PL-3601 'TSZ'
Wired Xbox 360 Controller to the device table.
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
"ret" should be signed here or the error handling doesn't work.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (59 commits)
igbvf.txt: Add igbvf Documentation
igb.txt: Add igb documentation
e100/e1000*/igb*/ixgb*: Add missing read memory barrier
ixgbe: fix build error with FCOE_CONFIG without DCB_CONFIG
netxen: protect tx timeout recovery by rtnl lock
isdn: gigaset: use after free
isdn: gigaset: add missing unlock
solos-pci: Fix race condition in tasklet RX handling
pkt_sched: Fix sch_sfq vs tcf_bind_filter oops
net: disable preemption before call smp_processor_id()
tcp: no md5sig option size check bug
iwlwifi: fix locking assertions
iwlwifi: fix TX tracer
isdn: fix information leak
net: Fix napi_gro_frags vs netpoll path
usbnet: remove noisy and hardly useful printk
rtl8180: avoid potential NULL deref in rtl8180_beacon_work
ath9k: Remove myself from the MAINTAINERS list
libertas: scan before assocation if no BSSID was given
libertas: fix association with some APs by using extended rates
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/ide-2.6:
tx493xide: use min_t() macro instead of min()
drivers/ide: Use memdup_user
via82cxxx: fix typo for VT6415 PCIE PATA IDE Host Controller support.
ide-cd: Do not access completed requests in the irq handler
According include/linux/console_struct.h,vc_scr_end is unsigned long.
struct vc_data {
unsigned short vc_num; /* Console number */
unsigned int vc_cols; /* [#] Console size */
unsigned int vc_rows;
unsigned int vc_size_row; /* Bytes per row */
unsigned int vc_scan_lines; /* # of scan lines */
unsigned long vc_origin; /* [!] Start of real screen */
unsigned long vc_scr_end; /* [!] End of real screen */
unsigned long vc_visible_origin; /* [!] Top of visible window */
unsigned int vc_top, vc_bottom; /* Scrolling region */
const struct consw *vc_sw;
unsigned short *vc_screenbuf;
...
}
Signed-off-by: qiaochong <qiaochong@loongson.cn>
Cc: Greg KH <greg@kroah.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
kernel will die on some platform when switch from vga mode to framebuffer
mode. The reason of this bug is that bind_con_driver reset vc->vc_origin
to (unsigned long)vc->vc_screenbuf.
On vgacon vc->vc_origin is not releated to vc->vc_screenbuf,if set
vc->vc_origin to vc->vc_screenbuf,kernel will die on vc_do_resize.
static int vc_do_resize(struct tty_struct *tty, struct tty_struct *real_tty,
struct vc_data *vc, unsigned int cols, unsigned int lines)
{
unsigned long old_origin, new_origin, new_scr_end, rlth, rrem, err = 0;
unsigned int old_cols, old_rows, old_row_size, old_screen_size;
unsigned int new_cols, new_rows, new_row_size, new_screen_size;
unsigned int end, user;
...
end = (old_rows > new_rows) ? old_origin +
(old_row_size * new_rows) :
vc->vc_scr_end;
...
/*
here for a test from vgacon to framebuffer:
old_origin=0x810814a0,end=0xb00b8fa0,vc->vc_origin=0x810814a0
the code bellow will copy memory from 0x810814a0 to 0xb00b8fa0,
this will cover kernel code,kernel died here.
*/
while (old_origin < end) {
scr_memcpyw((unsigned short *) new_origin,
(unsigned short *) old_origin, rlth);
if (rrem)
scr_memsetw((void *)(new_origin + rlth),
vc->vc_video_erase_char, rrem);
old_origin += old_row_size;
new_origin += new_row_size;
}
...
}
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: qiaochong <qiaochong@loongson.cn>
Cc: Greg KH <greg@kroah.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Allow device probing to recognise the Fintek F71808E.
Sysfs interface:
* Fan/pwm control is the same as for F71889FG
* Temperature and voltage sensor handling is largely the same as for
the F71889FG
- Has one temperature sensor less (doesn't have temp3)
- Misses one voltage sensor (doesn't have V6, thus in6_input refers to
what in7_input refers for F71889FG)
For the purpose of the sysfs interface fxxxx_in_temp_attr[] is split up
such that it can largely be reused.
Signed-off-by: Giel van Schijndel <me@mortis.eu>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
register_hotcpu_notifier() is designed to make these ifdefs unnecessary.
Cc: Chen Gong <gong.chen@linux.intel.com>
Cc: Rudolf Marek <r.marek@assembler.cz>
Cc: Huaxu Wan <huaxu.wan@intel.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Update coretemp supported CPU TjMax lists and some cleanup work.
Signed-off-by: Chen Gong <gong.chen@linux.intel.com>
Cc: Rudolf Marek <r.marek@assembler.cz>
Cc: Huaxu Wan <huaxu.wan@intel.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If one coretemp device can't be added, it should allow subsequent adding
operation because every new-added device will create a new sysfs group,
not an additional sensor sys entry.
Signed-off-by: Chen Gong <gong.chen@linux.intel.com>
Cc: Rudolf Marek <r.marek@assembler.cz>
Cc: Huaxu Wan <huaxu.wan@intel.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix two errors in hotplug. One is for hotplug notifier. The other is
unnecessary driver unregister. Because even none of online cpus supports
coretemp, we can't assume new onlined cpu doesn't support it either. If
related driver is unregistered there we have no chance to use coretemp
from then on.
Signed-off-by: Chen Gong <gong.chen@linux.intel.com>
Cc: Rudolf Marek <r.marek@assembler.cz>
Cc: Huaxu Wan <huaxu.wan@intel.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This driver adds support for the monitoring features of the Summit
Microelectronics SMM665 Six-Channel Active DC Output Controller/Monitor.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This driver will report the heading values in degrees to the sysfs
interface. The values returned are headings . e.g. 245.6
Alan: Cleanups requested now all folded in and a sysfs description to keep
Andrew happy. The sysfs description now resembles hwmon.
Signed-off-by: Kalhan Trisal <kalhan.trisal@intel.com>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add Lenovo Thinkpad T400. I have done the testing on my laptop. The
hdaps module detects the device and the hdapsd daemon is able to [un]park
the disk.
Signed-off-by: Ritesh Raj Sarraf <rrs@debian.org>
Cc: Frank Seidel <frank@f-seidel.de>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The error may happen at any iteration of the for loop, this patch properly
unregisters already registed edd_devices in error path.
[akpm@linux-foundation.org: remove unneeded NULL test]
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Stephen Hemminger <shemminger@vyatta.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The previous change added WARN_ON() in misc_deregister(). So it is not
necessary to WARN_ON() misc_deregister() failure by callers.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
misc_deregister() returns an error only when it attempts to unregister
the device that is not registered. This is the driver's bug.
Most of the drivers don't check the return value of misc_deregister().
(It is not bad thing because most of kernel *_unregister() API always
succeed and do not return value)
So it is better to indicate the error by WARN_ON() in misc_deregister().
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This driver adds support for the BMP085 digital pressure sensor from Bosch
Sensortec. It exposes a sysfs api to userspace where pressure and
temperature measurement results can be read from the pressure0_input and
temp0_input file. The chip is able to calculate the average of up to
eight samples to increase the accuracy. This feature can be controlled by
writing to the oversampling file.
The BMP085 digital pressure sensor can measure ambient air pressure and
temperature. Both values can be obtained from sysfs files. The pressure
is measured by reading from pressure0_input. Valid values range from
30000 to 110000 pascal with a resolution of 1 pascal (=0.01 millibar).
temp0_input holds the current temperature in degree celsius, multiplied by
10. This results in a resolution of a tenth degree celsius. Values range
from -400 to 850.
To increase the accuracy, this chip can calculate the average of 1, 2, 4
or 8 samples. This behavior is controlled through the oversampling sysfs
file. Two to the power of the value written to that file specifies how
many samples will be used. Valid values: 0..3.
[akpm@linux-foundation.org: fix typo]
[shubhrajyoti@ti.com: optimize the wait time for the pressure sensor, definition of long is arch dependent so make it u32]
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Christoph Mair <christoph.mair@gmail.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Cc: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix i386 PAE compile warning:
drivers/misc/hpilo.c: In function `ilo_ccb_setup':
drivers/misc/hpilo.c:274: warning: cast to pointer from integer of different size
dma_addr_t is 64 on i386 PAE which causes a size mismatch.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Acked-by: David Altobelli <david.altobelli@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for ROHM BH1780GLI Ambient light sensor.
BH1780 supports I2C interface. Driver supports read/update of power state
and read of lux value (through SYSFS). Writing value 3 to power_state
enables the sensor and current lux value could be read.
Currently this driver follows the same sysfs convention as supported by
drivers/misc/isl29003.c.
Signed-off-by: Hemanth V <hemanthv@ti.com>
Reviewed-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On some SoC chips, HW resources may be in use during any particular idle
period. As a consequence, the cpuidle states that the SoC is safe to
enter can change from idle period to idle period. In addition, the
latency and threshold of each cpuidle state can vary, depending on the
operating condition when the CPU becomes idle, e.g. the current cpu
frequency, the current state of the HW blocks, etc.
cpuidle core and the menu governor, in the current form, are geared
towards cpuidle states that are static, i.e. the availabiltiy of the
states, their latencies, their thresholds are non-changing during run
time. cpuidle does not provide any hook that cpuidle drivers can use to
adjust those values on the fly for the current idle period before the menu
governor selects the target cpuidle state.
This patch extends cpuidle core and the menu governor to handle states
that are dynamic. There are three additions in the patch and the patch
maintains backwards-compatibility with existing cpuidle drivers.
1) add prepare() to struct cpuidle_device. A cpuidle driver can hook
into the callback and cpuidle will call prepare() before calling the
governor's select function. The callback gives the cpuidle driver a
chance to update the dynamic information of the cpuidle states for the
current idle period, e.g. state availability, latencies, thresholds,
power values, etc.
2) add CPUIDLE_FLAG_IGNORE as one of the state flags. In the prepare()
function, a cpuidle driver can set/clear the flag to indicate to the
menu governor whether a cpuidle state should be ignored, i.e. not
available, during the current idle period.
3) add power_specified bit to struct cpuidle_device. The menu governor
currently assumes that the cpuidle states are arranged in the order of
increasing latency, threshold, and power savings. This is true or can
be made true for static states. Once the state parameters are dynamic,
the latencies, thresholds, and power savings for the cpuidle states can
increase or decrease by different amounts from idle period to idle
period. So the assumption of increasing latency, threshold, and power
savings from Cn to C(n+1) can no longer be guaranteed.
It can be straightforward to calculate the power consumption of each
available state and to specify it in power_usage for the idle period.
Using the power_usage fields, the menu governor then selects the state
that has the lowest power consumption and that still satisfies all other
critieria. The power_specified bit defaults to 0. For existing cpuidle
drivers, cpuidle detects that power_specified is 0 and fills in a dummy
set of power_usage values.
Signed-off-by: Ai Li <aili@codeaurora.org>
Cc: Len Brown <len.brown@intel.com>
Acked-by: Arjan van de Ven <arjan@linux.intel.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Venkatesh Pallipadi <venki@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
drivers/base/node.c: In function 'node_read_meminfo':
drivers/base/node.c:139: warning: the frame size of 848 bytes is
larger than 512 bytes
Fix it by splitting the sprintf() into three parts. It has no functional
change.
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a build failure "error: void value not ignored as it ought to be"
by removing an assignment of a void return value. The functionality of
the code is not changed.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Acked-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After the commit that changed ipmi_si detecting sequence from SMBIOS/ACPI
to ACPI/SMBIOS,
| commit 754d453185
| Author: Matthew Garrett <mjg@redhat.com>
| Date: Wed May 26 14:43:47 2010 -0700
|
| ipmi: change device discovery order
|
| The ipmi spec provides an ordering for si discovery. Change the driver to
| match, with the exception of preferring smbios to SPMI as HPs (at least)
| contain accurate information in the former but not the latter.
ipmi_si can not be initialized.
[ 138.799739] calling init_ipmi_devintf+0x0/0x109 @ 1
[ 138.805050] ipmi device interface
[ 138.818131] initcall init_ipmi_devintf+0x0/0x109 returned 0 after 12797 usecs
[ 138.822998] calling init_ipmi_si+0x0/0xa90 @ 1
[ 138.840276] IPMI System Interface driver.
[ 138.846137] ipmi_si: probing via ACPI
[ 138.849225] ipmi_si 00:09: [io 0x0ca2] regsize 1 spacing 1 irq 0
[ 138.864438] ipmi_si: Adding ACPI-specified kcs state machine
[ 138.870893] ipmi_si: probing via SMBIOS
[ 138.880945] ipmi_si: Adding SMBIOS-specified kcs state machineipmi_si: duplicate interface
[ 138.896511] ipmi_si: probing via SPMI
[ 138.899861] ipmi_si: Adding SPMI-specified kcs state machineipmi_si: duplicate interface
[ 138.917095] ipmi_si: Trying ACPI-specified kcs state machine at i/o address 0xca2, slave address 0x0, irq 0
[ 138.928658] ipmi_si: Interface detection failed
[ 138.953411] initcall init_ipmi_si+0x0/0xa90 returned 0 after 110847 usecs
in smbios has
DMI/SMBIOS
Handle 0x00C5, DMI type 38, 18 bytes
IPMI Device Information
Interface Type: KCS (Keyboard Control Style)
Specification Version: 2.0
I2C Slave Address: 0x00
NV Storage Device: Not Present
Base Address: 0x0000000000000CA2 (I/O)
Register Spacing: 32-bit Boundaries
in DSDT has
Device (BMC)
{
Name (_HID, EisaId ("IPI0001"))
Method (_STA, 0, NotSerialized)
{
If (LEqual (OSN, Zero))
{
Return (Zero)
}
Return (0x0F)
}
Name (_STR, Unicode ("IPMI_KCS"))
Name (_UID, Zero)
Name (_CRS, ResourceTemplate ()
{
IO (Decode16,
0x0CA2, // Range Minimum
0x0CA2, // Range Maximum
0x00, // Alignment
0x01, // Length
)
IO (Decode16,
0x0CA6, // Range Minimum
0x0CA6, // Range Maximum
0x00, // Alignment
0x01, // Length
)
})
Method (_IFT, 0, NotSerialized)
{
Return (One)
}
Method (_SRV, 0, NotSerialized)
{
Return (0x0200)
}
}
so the reg spacing should be 4 instead of 1.
Try to calculate regspacing for this kind of system.
Observed on a Sun Fire X4800. Other OSes work and pass certification.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-by: Matthew Garrett <mjg@redhat.com>
Cc: Len Brown <len.brown@intel.com>
Cc: Myron Stowe <myron.stowe@hp.com>
Cc: Corey Minyard <minyard@acm.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
drm: fix fallouts from slow-work -> wq conversion
workqueue: workqueue_cpu_callback() should be cpu_notifier instead of hotcpu_notifier
workqueue: add missing __percpu markup in kernel/workqueue.c
Replace inode_setattr with opencoded variants of it in all callers. This
moves the remaining call to vmtruncate into the filesystem methods where it
can be replaced with the proper truncate sequence.
In a few cases it was obvious that we would never end up calling vmtruncate
so it was left out in the opencoded variant:
spufs: explicitly checks for ATTR_SIZE earlier
btrfs,hugetlbfs,logfs,dlmfs: explicitly clears ATTR_SIZE earlier
ufs: contains an opencoded simple_seattr + truncate that sets the filesize just above
In addition to that ncpfs called inode_setattr with handcrafted iattrs,
which allowed to trim down the opencoded variant.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
proc_bus_zorro_read() didn't take into account the current file position,
hence it always read from the start of the ConfigDev.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Remove BKL use from proc_bus_zorro_lseek(), like was done for
proc_bus_pci_lseek() a long time ago.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
This feature provides a user interface to specify the timeout for
missing interrupts for standard I/O operations.
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The DASD reserve and release ioctls use the preallocated memory pool
of the respective device to build their CCW requests. However, when
the device is busy, the pool may already be empty and the ioctl fails.
Usually this can be recovered by calling the ioctl again, but in
a situation in which we need to issue an unconditional reserve to
make a device operational again, this would be not recoverable.
To avoid a failure due to lack of memory, DASD device driver will
preallocate enough memory for a single reserve/release request, which
can be used if normal allocation fails.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The sender kernel parameter contains a z/VM user ID where
alphabetic characters must be specified in uppercase.
Allow users to specify lowercase characters and convert the
sender string to uppercase at module initialization.
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use all available paths for the SENSE ID and STLCK commands. This
prevents deadlocks in conjunction with reserved devices.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Change the ccwrequest infrastructure to use more than one channel
path per start I/O. A flag "singlepath" is added to struct
ccw_request - if set, the old behavior is used. This flag is set
for all exploiters of the ccwrequest infrastructure - so there
is no functional change through this patch.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If no driver is attached to a device or the driver provides no
set_online/set_offline function, setting this device online/offline
via its sysfs online attribute will silently fail but return success.
This patch changes the behavior to return -EINVAL in those cases.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Log the response from the unit check handler which triggers further
cio internal i/o processing.
Signed-off-by: Michael Ernst <mernst@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
A Linux interface for the CHSC command
store-I/O-operation-status-and-initiate-logging (SIOSL).
Model-dependent logging within the channel subsystem can be invoked
via a helper function or a writable subchannel device attribute.
Signed-off-by: Michael Ernst <mernst@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add ioctl to CRIS serial driver to get RS485 data from user-space.
Signed-off-by: Claudio Scordino <claudio@evidence.eu.com>
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Commit 991ea75c (drm: use workqueue instead of slow-work), which made
drm to use wq instead of slow-work, didn't account for the return
value difference between delayed_slow_work_enqueue() and
queue_delayed_work(). The former returns 0 on success and -errno on
failures while the latter never fails and only uses the return value
to indicate whether the work was already pending or not.
This misconversion triggered spurious error messages. Remove the now
unnecessary return value check and error message.
Markus: caught another incorrect conversion in drm_kms_helper_poll_enable()
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Tested-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Cc: David Airlie <airlied@linux.ie>
Cc: dri-devel@lists.freedesktop.org
This fixes a warning ("comparison of distinct pointer types lacks a
cast") introduced by the commit
040f6b4f14 ("tx493xide: use ->pio_mode
value to determine pair device speed").
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use memdup_user when user data is immediately copied into the
allocated region.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression from,to,size,flag;
position p;
identifier l1,l2;
@@
- to = \(kmalloc@p\|kzalloc@p\)(size,flag);
+ to = memdup_user(from,size);
if (
- to==NULL
+ IS_ERR(to)
|| ...) {
<+... when != goto l1;
- -ENOMEM
+ PTR_ERR(to)
...+>
}
- if (copy_from_user(to, from, size) != 0) {
- <+... when != goto l2;
- -EFAULT
- ...+>
- }
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without this fix, init of the via82cxxx driver causes a oops with a
stack resembling the one below, and the boot blocks between init of
USB devices and launch of init (was easy to bisect by booting with
init=/bin/sh).
Pid: 279, comm: work_for_cpu Not tainted 2.6.34.1-00003-ga42ea77 #2
Call Trace:
[<ffffffff81045691>] ? warn_slowpath_common+0x76/0x8c
[<ffffffff810456f9>] ? warn_slowpath_fmt+0x40/0x45
[<ffffffff812eb5a1>] ? printk+0x40/0x47
[<ffffffff8108e1fd>] ? enable_irq+0x3e/0x64
[<ffffffffa0003900>] ? ide_probe_port+0x55c/0x589 [ide_core]
[<ffffffffa0003f22>] ? ide_host_register+0x273/0x628 [ide_core]
[<ffffffffa00083e3>] ? ide_pci_init_two+0x4da/0x5c5 [ide_core]
[<ffffffff8106117e>] ? up+0xe/0x36
[<ffffffff81045d7e>] ? release_console_sem+0x17e/0x1ae
[<ffffffff812d945b>] ? klist_iter_exit+0x14/0x1e
[<ffffffff8120ed23>] ? bus_find_device+0x75/0x83
[<ffffffffa0022832>] ? via_init_one+0x269/0x28a [via82cxxx]
[<ffffffffa00223a2>] ? init_chipset_via82cxxx+0x0/0x1ea [via82cxxx]
[<ffffffff81059f25>] ? do_work_for_cpu+0x0/0x1b
[<ffffffff81190c65>] ? local_pci_probe+0x12/0x16
[<ffffffff81059f30>] ? do_work_for_cpu+0xb/0x1b
[<ffffffff8105d0dd>] ? kthread+0x75/0x7d
[<ffffffff810097e4>] ? kernel_thread_helper+0x4/0x10
[<ffffffff8105d068>] ? kthread+0x0/0x7d
[<ffffffff810097e0>] ? kernel_thread_helper+0x0/0x10
---[ end trace 89c8cb70379b5bda ]---
The typo was introduced in a354ae8747,
and affects 2.6.33-rc4 and later.
Signed-off-by: Yann Dirson <ydirson@altern.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
ide_cd_error_cmd() can complete an erroneous request with leftover
buffers. Signal this with its return value so that the request is not
accessed after its completion in the irq handler and we oops.
Cc: <stable@kernel.org> # 32.x 33.x 34.x
Signed-off-by: Borislav Petkov <bp@alien8.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 04b4b88cca.
While the original problem only caused a slight disturbance on the
edge of the touchpad, the commit above to "fix" it completely breaks
operation on some other models such as mine.
We'll sort this out separately, revert the patch for now.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Based on patches from Sonny Rao and Milton Miller...
Combined the patches to fix up clean_tx_irq and clean_rx_irq.
The PowerPC architecture does not require loads to independent bytes
to be ordered without adding an explicit barrier.
In ixgbe_clean_rx_irq we load the status bit then load the packet data.
With packet split disabled if these loads go out of order we get a
stale packet, but we will notice the bad sequence numbers and drop it.
The problem occurs with packet split enabled where the TCP/IP header
and data are in different descriptors. If the reads go out of order
we may have data that doesn't match the TCP/IP header. Since we use
hardware checksumming this bad data is never verified and it makes it
all the way to the application.
This bug was found during stress testing and adding this barrier has
been shown to fix it. The bug can manifest as a data integrity issue
(bad payload data) or as a BUG in skb_pull().
This was a nasty bug to hunt down, if people agree with the fix I think
it's a candidate for stable.
Previously Submitted to e1000-devel only for ixgbe
http://marc.info/?l=e1000-devel&m=126593062701537&w=3
We've now seen this problem hit with other device drivers (e1000e mostly)
So I'm resubmitting with fixes for other Intel Device Drivers with
similar issues.
CC: Milton Miller <miltonm@bga.com>
CC: Anton Blanchard <anton@samba.org>
CC: Sonny Rao <sonnyrao@us.ibm.com>
CC: stable <stable@kernel.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Building ixgbe without DCB_CONFIG and FCOE_CONFIG will cause
a build error. This resolves the build error by wrapping
the fcoe.up in CONFIG_IXGBE_DCB ifdefs.
Also frames were being priority VLAN tagged even without DCB
enabled. This fixes this so that 8021Q priority tags are
only added with DCB actually enabled.
Reported-by: divya <dipraksh@linux.vnet.ibm.com>
Reported-by: Jon Mason <jon.mason@exar.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
H-PLL Feedback Divider LSB register is an 8 bit register out
of which the first 4 bits are reserved. Current code is
writing to these reserved location. This patch corrects
this issue by left shifting the values being written to the
register by 4.
This patch has been tested on DM6467 EVM with 720P-60 and
1080I-60 inputs.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Calling schedule() holding spinlock with disables irqs is improper. As
spinlock protects list coredev->buffers, it can be unlocked untill wakeup.
This bug was introduced in a9349315f6.
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Here a small patch to get a TwinHan VT DST DVB-T card working with
kernels >= 2.6.32. Analogously to
http://linuxtv.org/hg/v4l-dvb/rev/0e735b509163 I had to:
"Fill in the .caps field in struct dst_dvbt_ops (around line 1763) with
all the supported QAM modulation methods to match the capabilities of
the card as implemented in function dst_set_modulation (around line
502). Note that beginning with linux kernel version 2.6.32 the
modulation method is checked (by function dvb_frontend_check_parameters
in file drivers/media/dvb/dvb-core/dvb_frontend.c) and thus tuning fails
if you use a modulation method that is not present in the .caps field."
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
"ir_dev->props" can be NULL. We only use raw mode if "ir_dev->props" is
non-NULL and "ir_dev->props->driver_type == RC_DRIVER_IR_RAW".
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since this module is also used by drivers that are not yet converted, the old
and new code have to co-exist.
The source is split into three parts: a common part at the top, which is used
by both old and new code, then the old code followed by the new control
framework implementation. This new code is much more readable (and shorter!)
than the original code.
Once all bridge drivers that use this are converted the old code can be
deleted.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The cx25840 used a private control CX25840_CID_ENABLE_PVR150_WORKAROUND
to be told whether to enable a workaround for certain pvr150 cards.
This is really config data that it needs to get at load time.
Implemented this in cx25840 and ivtv.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add the calls needed to automatically merge subdev controls into a bridge
control handler.
Hook up the control framework in __video_ioctl2 and video_register_device.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
To make it easier to determine whether all controls are added in v4l2-ctrls.c
the case statements inside the switch are re-ordered to match the header.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a new framework to handle controls which makes life for driver
developers much easier.
Note that this patch moves some of the control support that used to be in
v4l2-common.c to v4l2-ctrls.c. The tables were copied unchanged. The body
of v4l2_ctrl_query_fill() was copied to a new v4l2_ctrl_fill() function
in v4l2-ctrls.c. This new function doesn't use the v4l2_queryctrl
struct anymore, which makes it more general.
The remainder of v4l2-ctrls.c is all new. Highlights include:
- No need to implement VIDIOC_QUERYCTRL, QUERYMENU, S_CTRL, G_CTRL,
S_EXT_CTRLS, G_EXT_CTRLS or TRY_EXT_CTRLS in either bridge drivers
or subdevs. New wrapper functions are provided that can just be plugged in.
Once everything has been converted these wrapper functions can be removed as well.
- When subdevices are added their controls can be automatically merged
with the bridge driver's controls.
- Most drivers just need to implement s_ctrl to set the controls.
The framework handles the locking and tries to be as 'atomic' as possible.
- Ready for the subdev device nodes: the same mechanism applies to subdevs
and their device nodes as well. Sub-device drivers can make controls
local, preventing them from being merged with bridge drivers.
- Takes care of backwards compatibility handling of VIDIOC_S_CTRL and
VIDIOC_G_CTRL. Handling of V4L2_CID_PRIVATE_BASE is fully transparent.
CTRL_CLASS controls are automatically added.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Moved mt9m111_init after the chip version detection passage: I
don't like the idea of writing on a device we haven't identified
yet.
Signed-off-by: Philipp Wiesner <p.wiesner@phytec.de>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Added this info to Kconfig and mt9m111.c, some comment cleanup,
replaced 'mt9m11x'-statements by clarifications or driver name.
Driver is fully compatible to mt9m131 which has only additional functions
compared to mt9m111. Those aren't used anyway at the moment.
Signed-off-by: Philipp Wiesner <p.wiesner@phytec.de>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The emma uses bufnum 1 and 0. This patch tells the bufqueue to change
the next buffer to the next one and not the current one.
Otherwise the BUG_ON above will trigger everytime.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tuner, DVB frontend and video helper chip drivers are by default
autoselected by their respective host cards, this, however, doesn't make
much sense on SoC-based systems. Disable autoselection on EMBEDDED
systems.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There is no sense in trying to set cropping if we cannot get current one
from the host driver.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The exchanges for sensor mt9v111 are different with bridges zc301 and zc303.
The exchanges for the bridge zc303 were those of the bad named tas5130ck.
These mt9v111 exchanges have been adjusted from the ms-Windows public files
vm30x.inf (for 0ac8:301b) and usbvm303.inf (for 0ac8:303b).
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The new exchanges are extracted from the public file lPEPI264v.inf of the
ms-Windows driver. In this file, the sensor is named hv7131b but the exchanges
are those of the hv7131r.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- use an enum to define the sensor numbers
- use the sensor numbers to index the associated tables
- rename TAS5130CXX to TAS5130C
- rename HV7131C to HV7131R
- change some comments
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some webcams as ov511 may find many times an end of image.
In this case, with the last patch in image concatenation
(commit 799b1bd41f398054d46fd35f73abd01c4009f6ca),
the image pointer was NULL and the system crashed in memcpy().
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This driver exports a video device node per each camera interface/
video postprocessor (FIMC) device contained in Samsung S5P SoC series.
The driver is based on v4l2-mem2mem framework.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Pawel Osciak <p.osciak@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The camera requires the STREAM_NO_FID quirk. Add a corresponding entry
in the device IDs list.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Corrupted video frames are dropped by default by the driver for
uncompressed formats. Data corruption is not less problematic for
compressed formats, so frame drop should be enabled by default for those
formats as well.
Mark buffers as faulty when an isochronous packet loss is detected for
any format, or when the buffer length doesn't match the image size for
uncompressed formats. Drop erroneous buffers regardless of whether the
format is compressed or uncompressed.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds a defintion for the "Print" button found on HP OEM
versions of the MCE remote. All of the other keys found on the HP OEM
version of the remote match the other keys as already defined.
Because, who doesn't need "remote printing", while one is sitting on the
couch across from one's PC? ;)
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add latest unported version of this driver to media/IR.
Next patch will port it to ir core.
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This way it is possible to use evtest to create keymap for unknown remote.
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
LIRC: add new IOCTL that enables learning mode (wide band receiver)
Still missing features: carrier report & timeout reports.
Will need to pack these into ir_raw_event
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some ir input devices have small buffer, and interrupt the host
each time it is full (or half full)
Add a helper that automaticly handles timeouts, and also
automaticly merges samples of same time (space-space)
Such samples might be placed by hardware because size of
sample in the buffer is small (a byte for example).
Also remove constness from ir_dev_props, because it now contains timeout
settings that driver might want to change
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently, ir device registration fails if keymap requested by driver is not found.
Fix that by always compiling in the empty keymap, and using it as a failback.
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This adds support for repeat detecting for NECX variant
Tested with uneversal remote
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Repeat space is 4 units, not 8.
Current code would never trigger a repeat.
However that isn't true for NECX, so repeat there
must be handled differently.
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Reviewed-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently, jvc decoder will attempt misdetect next press as a repeat
of last keypress, therefore second keypress isn't detected.
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It is perfectly possible to have ir_raw_event_work
running concurently on two cpus, thus we must protect
it from that situation.
This stems from the fact that if hardware sends short packets of samples
we might end up queueing the work item more times that nessesary.
Such job isn't well suited for a workqueue, so use a kernel thread.
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some handlers (lirc for example) allocates memory on initialization,
doing so in atomic context is cumbersome.
Fixes warning about sleeping function in atomic context.
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* lirc: Don't propagate reset event to userspace
* lirc: Remove strange logic from lirc that would make first sample always be pulse
* Make TO_US macro actualy print what it should.
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Move IR drives below separate menu.
This allows to disable them.
Also correct a typo.
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Moves drivers/staging/lirc/lirc_streamzap.c to
drivers/media/IR/streamzap.c, along with making the requisite Kconfig
and Makefile changes.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This ports lirc_streamzap.c over to ir-core in-place, to be followed by
a patch moving the driver over to drivers/media/IR/streamzap.c and
enabling the proper Kconfig bits.
Presently, the in-kernel keymap doesn't work, as the stock Streamzap
remote uses an RC-5-like, but not-quite-RC-5 protocol, which the
in-kernel RC-5 decoder doesn't cope with. The remote can be used right
now with the lirc bridge driver though, and other remotes (at least an
RC-6(A) MCE remote) work perfectly with the driver.
I'll take a look at making the existing RC-5 decoder cope with this odd
duck, possibly implement another standalone decoder engine, or just
throw up my hands and say "meh, use lirc"... But the driver itself
should be perfectly sound.
Remaining items on the streamzap TODO list:
- add LIRC_SET_REC_TIMEOUT-alike support
- add LIRC_GET_M{AX,IN}_TIMEOUT-alike support
- add LIRC_GET_REC_RESOLUTION-alike support
All of the above should be trivial to add. There are patches pending to
add this support to ir-core from Maxim Levitsky, and I'll take care of
these once his patches get integrated. None of them are currently
essential though.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix when CONFIG_MODULES is not enabled:
drivers/staging/lirc/lirc_parallel.c:243: error: implicit declaration of function 'module_refcount'
drivers/staging/lirc/lirc_it87.c:150: error: implicit declaration of function 'module_refcount'
drivers/built-in.o: In function `it87_probe':
lirc_it87.c:(.text+0x4079b0): undefined reference to `init_chrdev'
lirc_it87.c:(.text+0x4079cc): undefined reference to `drop_chrdev'
drivers/built-in.o: In function `lirc_it87_exit':
lirc_it87.c:(.exit.text+0x38a5): undefined reference to `drop_chrdev'
Its a quick hack and untested beyond building, since I don't have the
hardware, but it should do the trick.
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The ir_input_dev gets filled in by __ir_input_register, the one
allocated in mceusb_init_input_dev was being overwritten by the correct
one shortly after it was initialized (ultimately resulting in a memory
leak). This bug was inherited from imon.c, and was pointed out to me by
Maxim Levitsky.
v2: fix incorrect dev arg to dev_dbg
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The ir_input_dev gets filled in by __ir_input_register, the one
allocated in imon_init_idev was being overwritten by the correct one
shortly after it was initialized (ultimately resulting in a memory
leak). Additionally, there was an ill-advised memcpy into that
extraneous ir_input_dev which gets fixed by this.
Ill-advised memcpy pointed out by Dmitry Torokhov, bad usage of
ir_input_dev pointed out by Maxim Levitsky.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Per Dmitry Torokhov, following input_unregister_device with an
input_free_device is forbidden, the former is sufficient alone.
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The CX23885 and CX25840 modules were using their own simple
IR pulse width measurement record type which required conversion
when passing to the new IR core. This change makes that record type
consistent with the new IR core and removes a data conversion.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of reporting an IR Rx timeout event as a ridiculously
long space, report it as a space of the lenght of the timeout.
This partially fixes operation with LIRC without breaking
interoperation with the in kernel decoders. The gaps lengths
reported to LIRC are still not real however.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Compute and report the maximum IR pulse measurment width, even
if we are set to perform carrier modulation or demodulation and
the number is fixed by the carrier freq.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This driver no longer depends on the old IR functions selected by
VIDEO_IR.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The CX23885 IR controller was reported to cause an interrupt storm
on a TeVii S470 card, but was reported fine on an HVR-1250. Keep
integrated IR disabled by default on CX2388[57] based cards to avoid
a bad user experience in the general case.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Interrupts from the AV Core are best handled by a workqueue handler
since many I2C transactions are required to service the AV Core
interrupt. The AV_CORE PCI interrupt is disabled by the IRQ handler
and reenabled when the work handler is finished.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch encapsulates access to the PCI_INT_MSK register and
dev->pci_irqmask variable and protects them with a spinlock.
This is needed because both the hard IRQ handler and a workhandler
will need to manipulate the mask to disable the AV_CORE interrupt.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add initial IR Rx support using the intergrated IR controller in the
A/V core of the CX23885 bridge chip.
This initial support is flawed in that I2C transactions should not
be performed in a hard irq context. That will be fixed in a
follow on patch.
The TeVii S470 support is reported to generate perptual interrupts
that renders a user' system nearly unusable. The TeVii S470 IR
will be disabled by default in a follow on patch.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch is primarily a port of the integrated IR controller code in
cx23885/cx23888-ir.c. Right now, only the CX2388[57] AV core will
really try to set up IR. This IR support, by design, still requires the
bridge driver to do final IO pin mux configuration and setup of the IR
controller parameters.
For the CX2388[578] chips, enabling the AV Core for IR also starts
sending Audio and Video interrupts to the bridge driver. For
CX2388[578] chips audio and video interrupts are ignored and
acknowledged when they happen.
IR interrupt handling and status logging is exluded for the CX23888
which does not have an IR controller on the AV core.
Note that experimentation reveals that the IR irq enables on the
CX23885 have an inverted logic sense. The CX23887 likely suffers from
the same quirk. For these chips, those irq enable bits are handled
as interrupt disables.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The CX2584x and related cores are multifunction subdevices with a number
of internal blocks that act as interrupt sources. Move the v4L2_subdev
interrupt_service_routine callback from v4l_subdev_ir_ops to
v4l2_subdev_core_ops, as the video and audio blocks of a CX2584x and
related cores can generate interrupts along with the IR block. This
change also makes sense for other subdev's that generate interrupts and
do not have an IR block.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Explicitly configure the IR Tx and IR Rx pins to be driven by the
IR Rx and Tx pads from the AV core for CX23888 IR.
For the HVR-1850 and HVR-1290 configure the IR Tx level inversion,
so the Tx LED is off when idle.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There is a distinction on IR Tx for the CX2388[578] chips of carrier
sense inversion (space is a carrier burst and mark is no burst) and I/O
pin level inversion (0 is high output level, 1 is low output level).
Allow the caller to set these parameters distinctly as v4l2_subdevice
IR parameters. This permits the IR device to be configured and enabled
without the IR Tx LED being on during idle/space time due to an external
hardware level inversion
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add s_io_pin_config core subdev op for the CX2388[578] AV cores.
This is complete for IR_RX, IR_TX, GPIOs 16,19-23, and IRQ_N.
It likely needs work for the I2S signal direction.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a simple log_status function for raw analog video capture device nodes,
to provide insight into the state of the CX2388[578] A/V decoder core.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The offset in the eeprom data for the 79501 version of the HVR-1250 is at 0xc0
vs. the standard 0x80.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There was a small window between writing the cx25840 register
address over the i2c bus and reading the register contents back from the
cx25840 device that the i2c adapter lock was released. This change ensures the
adapter lock is not released until the register read is done.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Function i2c_wait_done() never returns negative values, so there is no
point in checking for them.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
