I2S MCLK has been routed to LSE connector on the MinnowBoard
starting with HW version 3. Older versions of the board do
not have MCLK wired.
Add dmi quirk to disable MCLK for MinnowBoard MAX (v2).
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use platform clocks "pmc_plt_clk_3" when MCLK quirk is defined.
By default always enable the 19.2 MHz PLL.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some platforms have the analog mic connected to IN3,
add route accordingly
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Auto routing based on Baytrail/Baytrail-CR detection
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Allow for all possible combinations of SSP0,SSP2, AIF1, AIF2
combination (only one at a time)
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add quirk to model routing on Baytrail-CR devices
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Existing code used SSP2, make selection of SSP id
dependent on port name. This is required when the
machine driver uses non-default settings
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Atom DPCM driver only allowed for the SSP2 interface, add
definitions for modem/SSP0.
These definitions might be used to route audio to a codec
connected to SSP0 (instead of a modem in traditional usages),
but there is a restriction to 2ch I2S. SSP2 is capable of
handling up to 4 slot TDM.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
BYT-CR needs special handling to deal with BIOS issues.
For some reason the IPC interrupt index is also modified from
the Baytrail-T reference.
Use PUNIT BIOS config bits to infer platform details.
Assume regular Baytrail configs if status is incorrect or
CONFIG_IOSF_MBI is not enabled.
SSP0 routing issues are solved without dedicated firmware
in following patches
Tested on Asus T100TA and T100TAF.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some Baytrail-CR devices rely on analog mics connected with
differential pairs and not the single-ended default
Add quirk and enable it for T00TAF
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some Baytrail devices only have a mono speaker, add quirk and enable
it for T100TAF.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add quirk based on DMI string matching
Also fix matching to use DMI_EXACT_MATCH otherwise T100TA and T100TAF
will be using same quirk
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix to return error code -ENODEV from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: 87b2bdf022 ("ASoC: Intel: Skylake: Initialize NHLT table")
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Acked-By: Vinod Koul <vinod.kou@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now that we have balanced loading of the topology file and split of init
and fw_init and fill module data during asoc probe.
So remove it from runtime, but keep error check in case things fall apart.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Once topology and firmware are loaded, we can parse the manifest. Use driver
pipe and widget list to get list of all modules and populate the data.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
snd_skl_get_module_info() takes skl_dfw_module as an argument. The users
then updates the topology data, so instead pass skl_module_cfg and let
snd_skl_get_module_info() fill that up.
Signed-off-by: Dharageswari R <dharageswari.r@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now that we have the bus parse capabilities moved to core, we need to
convert users.
The SKL driver and HDA extended lib needs to converted in single patch,
otherwise we regress on the functionality.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A module can be scheduled in deferent processing domains in DSP. Topology
specifies the module domain.
Signed-off-by: Senthilnathan Veppur <senthilnathanx.veppur@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
While changing code notice bad comment style, so fix it up.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The library load is added as one of the ops in skl_dsp_fw_ops().
The manifest load gives the files to be loaded which are loaded during
the fw_init()
Signed-off-by: Ramesh Babu <ramesh.babu@intel.com>
Signed-off-by: Kranthi G <gudishax.kranthikumar@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
sound/soc/intel/skylake/skl-topology.c:480:24-30: ERROR: application of sizeof to pointer
sizeof when applied to a pointer typed expression gives the size of
the pointer
Generated by: scripts/coccinelle/misc/noderef.cocci
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DSP fw can have additional firmwares as libs. These libs can be
loaded using message IPC_GLB_LOAD_LIBRARY.
Signed-off-by: Ramesh Babu <ramesh.babu@intel.com>
Signed-off-by: Kranthi G <gudishax.kranthikumar@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The firmware manifest contains UUIDs which needs to be passed only once.
So use the newly introduced is_first_boot flag to distinguish and parse
these only once on bxt platform as well.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The firmware manifest contains UUIDs which needs to be passed only once.
So use the newly introduced is_first_boot flag to distinguish and parse
these only once.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For additional library parsing, we need to pass firmware to be
loaded and not use the pointer in context. Also, Library module
IDs are combination of library index and module ID in manifest.
So add the additional arguments of firmware and library offset to
snd_skl_parse_uuids().
Signed-off-by: Senthilnathan Veppur <senthilnathanx.veppur@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Topology manifest gives information about the libraries to be
loaded. Implement the topology manifest load callback to get
this.
Signed-off-by: Kranthi G <gudishax.kranthikumar@intel.com>
Signed-off-by: Senthilnathan Veppur <senthilnathanx.veppur@intel.com>
Signed-off-by: Ramesh Babu <ramesh.babu@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The DSP instance creation also loads the firmware on DSPs. For library load
the firmware names come from topology so can't be loaded at object creation.
So split the firmware load and object creation. FW load is now called after
topology init in platform probe.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To query the ops used for a platform, we use skl_get_dsp_ops() which return
index and then we load the ops.
Rather than this return the ops, this way it cna be used later to query the
ops in rest of the driver.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since we are moving DSP init to later, at the topology load the
module info is not available.
So set the module id to -1 at init and query at first module
initialization.
Signed-off-by: Senthilnathan Veppur <senthilnathanx.veppur@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Module list can be NULL so check if the list is empty before
accessing the list.
Signed-off-by: Senthilnathan Veppur <senthilnathanx.veppur@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The release_firmware() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
The following bug was reported by sometime back:
https://lkml.org/lkml/2016/6/29/795
This commit fixes this bug by setting value for the prefix string.
Signed-off-by: Vedang Patel <vedang.patel@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
soc-core sets the snd_soc_pcm_runtime->dev drvdata to
snd_soc_pcm_runtime in soc_post_component_init, and access
it in places like codec_reg_show.
hsw_pcm_open overwrites the drvdata to point to hsw_pcm_data,
confusing soc-core, and causing crashes when cat
/sys/devices/pci0000:00/INT3438:00/.../System PCM/codec_reg
This patch removes the set in hsw_pcm_open since it's no longer
used. commit 7ff9d6714a ("ASoC: Intel: Split hsw_pcm_data for
playback and capture") already removed all calls to
snd_soc_pcm_get_drvdata(rtd).
Signed-off-by: Ben Zhang <benzh@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Like SKL we have skl_nau88l25_ssm4567 machine for KBL,
so add the ID for this machine too.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Like SKL we have skl_nau88l25_max98357a machine for KBL,
so add the ID for this machine too.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Like SKL, we have two more machines for KBL, so add these IDs
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The platform device id table expects names to be less that
20chars, so truncate the name in skl id table and
skl_nau88l25_max98357a machine.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The platform device id table expects names to be less that
20chars, so truncate the name in skl id table and
skl_nau88l25_ssm4567 machine.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
FW reload had two issues:
- We need to disable the core 0 on when fw fails
- Before loading firmware mark boot flag as false
This patch fixes these two
Signed-off-by: Senthilnathan Veppur <senthilnathanx.veppur@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Kabylake platform is similar to Skylake. So, add machine id.
Since same machine driver supports both, add these in id table.
Signed-off-by: Shreyas NC <shreyas.nc@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Kabylake is next generation Intel platform which has similar
audio controller to Skylake, so add the ID and driver data in
SKL driver.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now we correctly error an attempt to execute an unsupported operation.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The module list was not initialized for Broxton DSP code, so
initialize it.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The recent commit [a92ea59b74: ASoC: Intel: sst: only select
sst-firmware when DW DMAC is built-in] introduced more strict kconfig
dependency (depends on DW_DMAC_CORE=y) for avoiding the build failures
due to dependency messes in intel-sst. This makes, however, it
impossible to use this driver with the modularized systems,
i.e. typically on Linux distros.
The problem addressed in the commit above is that sst_dsp_new() and
sst_dsp_free() includes the firmware init / finish that call dw_*()
functions. Thus building it as built-in with DW_DMAC_CORE module
results in the missing symbols.
However, these sst_dsp functions are basically called only from the
drivers that depend on DW_DMAC_CORE already. That is, once when these
functions are split out, the rest can be independent from dw stuff.
This patch attempts to solve the issue by the following:
- Split sst-dsp stuff into two modules: snd-soc-sst-dsp and
snd-soc-sst-firmware.
- Move sst_dsp_new() and sst_dsp_free() to the latter module so that
the former module can be independent from DW_DMAC_CORE.
- Add a new kconfig SND_SOC_INTEL_SST_FIRMWARE to select the latter
module by machine drivers.
One only remaining pitfall is that each machine driver has to select
SND_SOC_INTEL_SST_FIRMWARE carefully depending on DW_DMAC_CORE.
This can't be done cleanly due to the restriction of the current
kbuild.
Bugzilla: https://bugzilla.opensuse.org/show_bug.cgi?id=988117
Fixes: a92ea59b74 ('ASoC: Intel: sst: only select sst-firmware when DW DMAC is built-in')
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Sparse rightly warns:
sound/soc/intel/atom/sst/sst_acpi.c:353:22: warning: symbol 'cht_quirk' was not declared. Should it be static?
So statify this
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Kbuild bot reports that we might use dai_index uninitialized.
sound/soc/intel/boards/cht_bsw_rt5645.c:391:37: warning: 'dai_index' may be used uninitialized in this function [-Wmaybe-uninitialized]
Since it is theoretically possible, set it while initializing.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DSP expects the actual length of parameters that is set through
TLV to be passed in large config set, so pass the actual size
received in tlv_control_set() instead of max size.
Signed-off-by: Dharageswari R <dharageswari.r@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Surface3 device is a CHT machine, so add entry for it.
Also update the HID from BIOS.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=98001
Signed-off-by: Sachin Mokashi <sachinx.mokashi@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Surface 3 is CHT based device which shows up with RT5645 codec. But the
BIOS reports ACPI ID as 5640!
To solve this, add a DMI overide for cht-5640 machine.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=98001
Signed-off-by: Sachin Mokashi <sachinx.mokashi@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is log spam while doing playback, record or reloading the
audio firmware.
print_hex_dump uses printk(KERN_DEBUG,... which is different from
dev_dbg used elsewhere in the driver: it's always enabled at
compile-time. Change it to print_hex_dump_debug for logging consistency.
For consistency with other log statements, change dev_info to dev_dbg
for a kernel print which is frequently printed by the driver.
Signed-off-by: Vedang Patel <vedang.patel@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For consistency with other log statements, change dev_info to dev_dbg
for a kernel print which is frequently printed by the driver.
Signed-off-by: Vedang Patel <vedang.patel@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now we correctly error an attempt to execute an unsupported operation.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add multicore DSP support in Broxton DSP operations.
Signed-off-by: Jayachandran B <jayachandran.b@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add multicore DSP support in Skylake DSP operations.
Signed-off-by: Jayachandran B <jayachandran.b@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The DSP can have more than one cores. In that case the secondary
core has to be managed by the driver. This patch adds the changes
to driver infrastructure to support multiple core.
A new object skl_dsp_cores is introduced to support multiple
core. Helpers skl_dsp_get_core() skl_dsp_put_core() help to
managed the cores.
Many of the power_up/down and DSP APIs take additional argument
of core_id. The primary core, 0 is always powered up first and
then on demand second core.
Signed-off-by: Jayachandran B <jayachandran.b@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Noticed a style inconsistency in a comment, so update that
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We do not support async suspend due to dependency with rest of
card and require suspend/resume be executed synchronously, mark
the device accordingly.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This reverts commit 3513798ca4 ("ASoC: Intel: Add support for
PM ops in bxt-rt298") as the right way to fix this is to disable
async suspend
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Kconfig help texts were missing periods as suggested by Randy.
Also fix the alignment on a block of help text to be consistent
with rest.
Suggested-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Randy reported following error when ACPI is not enabled:
warning: (SND_SOC_INTEL_BYTCR_RT5640_MACH && SND_SOC_INTEL_BYTCR_RT5651_MACH
&& SND_SOC_INTEL_CHT_BSW_RT5672_MACH && SND_SOC_INTEL_CHT_BSW_RT5645_MACH &&
SND_SOC_INTEL_CHT_BSW_MAX98090_TI_MACH) selects SND_SST_IPC_ACPI
+which has unmet direct dependencies (SOUND && !M68K && !UML && SND &&
SND_SOC && ACPI)
causing these build errors:
In file included from ../sound/soc/intel/atom/sst/sst_acpi.c:40:0:
../include/acpi/acpi_bus.h:65:20: error: conflicting types for
'acpi_evaluate_dsm'
union acpi_object *acpi_evaluate_dsm(acpi_handle handle, const u8 *uuid,
In file included from ../sound/soc/intel/atom/sst/sst_acpi.c:31:0:
../include/linux/acpi.h:676:34: note: previous definition of
'acpi_evaluate_dsm' was here
static inline union acpi_object *acpi_evaluate_dsm(acpi_handle handle,
CONFIG_SND_SST_IPC_ACPI was already dependent upon ACPI, but that was not
solving it. So move the depends up to machine drivers and remove from
CONFIG_SND_SST_IPC_ACPI.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
While clearing loaded module count, we should check first to see
if module list is NULL or not. Some distributions can ship with
no modules and thus list can be empty.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We need card to be early suspended and late resumed, so use prepare and
complete for card suspend and resume.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Senthilnathan Veppur <senthilnathanx.veppur@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The stall bits needs to comprehend the number of DSP cores
running, so update the stall and unstall register writes to
comprehend SKL_DSP_CORES_MASK values as well.
Signed-off-by: Jayachandran B <jayachandran.b@intel.com>
Signed-off-by: Ramesh Babu <ramesh.babu@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Broxton needs to send Purge firmware IPC to DSP before downloading the
firmware. The DMA id needs to be updated for that.
While at it also update Broxton boot sequence to send purge request after
power up and before yanking off reset.
Signed-off-by: Senthilnathan Veppur <senthilnathanx.veppur@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Broxton DSP needs retains code loaded during runtime_pm cycles.
But it looses that on suspend cycle, so on resume we need to
download the firmware again.
This is done by adding a new flag and based on flag status, we
download the firmware.
Signed-off-by: Jayachandran B <jayachandran.b@intel.com>
Signed-off-by: Senthilnathan Veppur <senthilnathanx.veppur@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Capture from DMIC requires that we ignore the suspend, so mark
these as ignore_suspend in bxt-rt298 machine.
Signed-off-by: Senthilnathan Veppur <senthilnathanx.veppur@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We support stereo 48Khz audio, so add these as constraints
for this card
Signed-off-by: Senthilnathan Veppur <senthilnathanx.veppur@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Like Skylake, we can support 4 channel for DMIC, so add
hw_params and constraints in the bxt-rt298 machine
While at it, also add codec1 pipe for speaker playback.
Signed-off-by: Senthilnathan Veppur <senthilnathanx.veppur@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Don't update the runtime_delay in pointer query, delay need to
reported as part of soc driver ops delay function. The delay
value overwritten by ASoC core so this is dummy code and hence
removing it.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For pass through pipe, Host and Link DMA id's are valid,
instead of overwriting the params set the host and link
based on pipe type.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DSP pipe type can be a pass through or it can be processing pipe.
In case of pass through pipe, it is a single pipeline with both
host and link copier in the same pipeline.
Identify the DSP pipe type if it pass through or not. Pass through
pipe is identified by checking if it has both host and link copier
in the same pipeline.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We need to Identify the DSP pipe type and based on it being a pass
thru pipeline or not, we need to copy the pipeline params.
Pipe to widget mapping was earlier done in pre PMD widget handler,
but since the pipe type would now be required in hw_params for
bypass pipelines we need to move this to be done during the ASoC
probe of the platform component.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
On suspend firmware is re-initialized so resources are reset inside
firmware. Driver should also clear the firmware counters at this time.
Signed-off-by: Dharageswari R <dharageswari.r@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When DSP pipe/module is not initialized successfully, memory/mcps
is not allocated. So check the pipe/module state to avoid freeing
up of unallocated memory/mcps. And allocate resources when pipe/
module is initialized successfully.
Signed-off-by: Dharageswari R <dharageswari.r@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SW needs to set the PGCTL.LSRMD = 1 to disable LPSRAM retention
feature,otherwise it may lead to SRAM ECC Errors.
Signed-off-by: Dharageswari R <dharageswari.r@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If pipeline is not STARTED, we do not need to pause pipeline while
deleting.
Signed-off-by: Dharageswari R <dharageswari.r@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When pipe is stopped/Paused, set the pipe state to paused instead
of created.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In case of XRUN recovery PCM prepare will be called. In this case
Host/Link DMAs are reset and reconfigured, hence the corresponding
FE/BE pipe needs to be reset in order to get to a clean state.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds bxt_da7219_max98357a_i2s machine driver
entry into machine table
Signed-off-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds Broxton-P I2S machine driver which uses
DA7219 and MAX98357A codecs.
Signed-off-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This machine driver can support 2 or 4 DMIC configuration, so
apply the ch constraint according to driver pdata.
Signed-off-by: Yong Zhi <yong.zhi@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This machine driver can support 2 or 4 DMIC configuration, so
apply the ch constraint according to driver pdata.
Signed-off-by: Yong Zhi <yong.zhi@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Broxton uses different offset in manifest for parsing module
table. So invoke common parsing utility from broxton using
broxton offset.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SKylake uses different offset in manifest for parsing module
table. So invoke common parsing utility from skylake using
skylake offset.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Module params like module_id and loadable flag can be changed
in the DSP Firmware. These are kept in the firmware manifest
and driver should read these values from this manifest.
So, add support to parse the DSP firmware manifest and
read these module params.
Signed-off-by: Shreyas NC <shreyas.nc@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Broxton firmrware comes with extended manifest so invoke
skl_dsp_strip_extended_manifest() to check and strip
Signed-off-by: Ramesh Babu <ramesh.babu@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Future firmware updates may comes with extended manifest so invoke
skl_dsp_strip_extended_manifest() to check and strip
Signed-off-by: Shreyas NC <shreyas.nc@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We have firmware pointer is driver context, so use that instead
of local pointer.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some upcoming platforms like broxton etc have extended manifest
in firmware binary. This is not required to be downloaded to DSP.
So driver needs to strip this before downloading.
Add a utility function to check if a header exists, and remove it
in that case
Signed-off-by: Ramesh Babu <ramesh.babu@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Skylake can be configured with either both 2 and 4 channel DMIC
array, or 2 channel DMIC array only, this patch provides an API to
retrieve the DMIC info from nhlt.
Signed-off-by: Yong Zhi <yong.zhi@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Only mono channel is allowed for refcap device.
Signed-off-by: Yong Zhi <yong.zhi@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add constraint for ref DMIC to match with the
topology firmware config.
Signed-off-by: Yong Zhi <yong.zhi@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This function stub should have been 'static' in the original patch
so that multiple uses of the header file (in different drivers)
will not cause multiple function definitions.
sound/soc/intel/boards/built-in.o: In function `sst_acpi_find_name_from_hid':
(.text+0x560): multiple definition of `sst_acpi_find_name_from_hid'
sound/soc/intel/atom/built-in.o:(.text+0x10610): first defined here
../scripts/Makefile.build:369: recipe for target 'sound/soc/intel/built-in.o' failed
Fixes: f17131a93f: add function stub when ACPI is not enabled
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This time was again a relatively calm development cycle; most of
updates are about drivers, and no radical changes are seen in any
core code. Here are some highlights:
ALSA core:
- Continued hardening of ALSA hrtimer
- A few leak fixes in timer interface
- Fix poll error handling in PCM and compress
- Add error propagation in compress API
- Removal of dead rtctimer driver
HD-audio:
- Native ELD notify support for i915 HDMI
- Realtek ALC234 & co support
- Code refactoring to standardize chmap support
- Continued development for SKL HDMI core support
Firewire:
- Apply delayed card registration to all drivers
- Improved / stabilized the handling of PCM stream start / stop
- Add tracepoints to dump a part of isochronous packet data
- Fixed incoming/outgoing packet parameter usages
- Add support for M-Audio profire series
USB-audio:
- Fixes for UAC2 clock source
- SS+ support
- Workaround for oft-seen repeated sample rate read errors
ASoC:
- Further slow progress on the topology code
- Substantial updates and improvements for the da7219, es8328,
fsl-ssi, Intel and rcar drivers.
- Compress error handling in WM ADSP driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=QsAc
-----END PGP SIGNATURE-----
Merge tag 'sound-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"This time was again a relatively calm development cycle; most of
updates are about drivers, and no radical changes are seen in any core
code. Here are some highlights:
ALSA core:
- Continued hardening of ALSA hrtimer
- A few leak fixes in timer interface
- Fix poll error handling in PCM and compress
- Add error propagation in compress API
- Removal of dead rtctimer driver
HD-audio:
- Native ELD notify support for i915 HDMI
- Realtek ALC234 & co support
- Code refactoring to standardize chmap support
- Continued development for SKL HDMI core support
Firewire:
- Apply delayed card registration to all drivers
- Improved / stabilized the handling of PCM stream start / stop
- Add tracepoints to dump a part of isochronous packet data
- Fixed incoming/outgoing packet parameter usages
- Add support for M-Audio profire series
USB-audio:
- Fixes for UAC2 clock source
- SS+ support
- Workaround for oft-seen repeated sample rate read errors
ASoC:
- Further slow progress on the topology code
- Substantial updates and improvements for the da7219, es8328,
fsl-ssi, Intel and rcar drivers.
- Compress error handling in WM ADSP driver"
* tag 'sound-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (177 commits)
ALSA: firewire-lib: change a member of event structure to suppress sparse wanings to bool type
sound: oss: Use setup_timer and mod_timer.
ASoC: hdac_hdmi: Remove the unused 'timeout' variable
ASoC: fsl_ssi: Fix channel slipping on capture (or playback) restart in full duplex.
ASoC: fsl_ssi: Fix channel slipping in Playback at startup
ASoC: fsl_ssi: Fix samples being dropped at Playback startup
ASoC: fsl_ssi: Save a dev reference for dev_err() purpose.
ASoC: fsl_ssi: The IPG/5 limitation concerns the bitclk, not the sysclk.
ASoC: fsl_ssi: Real hardware channels max number is 32
ASoC: pcm5102a: Add support for PCM5102A codec
ASoC: hdac_hdmi: add link management
ASoC: Intel: Skylake: add link management
ALSA: hdac: add link pm and ref counting
ALSA: au88x0: Fix zero clear of stream->resources
ASoC: rt298: Add DMI match for Broxton-P reference platform
ASoC: rt298: fix null deref on acpi driver data
ASoC: dapm: deprecate MICBIAS widget type
ALSA: firewire-lib: drop skip argument from helper functions to queue a packet
ALSA: firewire-lib: add context information to tracepoints
ALSA: firewire-lib: permit to flush queued packets only in process context for better PCM period granularity
...
This time round the update brings in following changes:
- New tegra driver for ADMA device
- Support for Xilinx AXI Direct Memory Access Engine and Xilinx AXI Central
Direct Memory Access Engine and few updates to this driver.
- New cyclic capability to sun6i and few updates.
- Slave-sg support in bcm2835.
- Updates to many drivers like designware, hsu, mv_xor, pxa, edma,
qcom_hidma & bam.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=0Sy7
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-4.7-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
"This time round the update brings in following changes:
- new tegra driver for ADMA device
- support for Xilinx AXI Direct Memory Access Engine and Xilinx AXI
Central Direct Memory Access Engine and few updates to this driver
- new cyclic capability to sun6i and few updates
- slave-sg support in bcm2835
- updates to many drivers like designware, hsu, mv_xor, pxa, edma,
qcom_hidma & bam"
* tag 'dmaengine-4.7-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (84 commits)
dmaengine: ioatdma: disable relaxed ordering for ioatdma
dmaengine: of_dma: approximate an average distribution
dmaengine: core: Use IS_ENABLED() instead of checking for built-in or module
dmaengine: edma: Re-evaluate errors when ccerr is triggered w/o error event
dmaengine: qcom_hidma: add support for object hierarchy
dmaengine: qcom_hidma: add debugfs hooks
dmaengine: qcom_hidma: implement lower level hardware interface
dmaengine: vdma: Add clock support
Documentation: DT: vdma: Add clock support for dmas
dmaengine: vdma: Add config structure to differentiate dmas
MAINTAINERS: Update Tegra DMA maintainers
dmaengine: tegra-adma: Add support for Tegra210 ADMA
Documentation: DT: Add binding documentation for NVIDIA ADMA
dmaengine: vdma: Add Support for Xilinx AXI Central Direct Memory Access Engine
Documentation: DT: vdma: update binding doc for AXI CDMA
dmaengine: vdma: Add Support for Xilinx AXI Direct Memory Access Engine
Documentation: DT: vdma: update binding doc for AXI DMA
dmaengine: vdma: Rename xilinx_vdma_ prefix to xilinx_dma
dmaengine: slave means at least one of DMA_SLAVE, DMA_CYCLIC
dmaengine: mv_xor: Allow selecting mv_xor for mvebu only compatible SoC
...
* acpi-pci:
ACPI,PCI,IRQ: remove SCI penalize function
ACPI,PCI,IRQ: remove redundant code in acpi_irq_penalty_init()
ACPI,PCI,IRQ: reduce static IRQ array size to 16
ACPI,PCI,IRQ: reduce resource requirements
* acpi-misc:
ACPI / sysfs: fix error code in get_status()
ACPI / device_sysfs: Clean up checkpatch errors
ACPI / device_sysfs: Change _SUN and _STA show functions error return to EIO
ACPI / device_sysfs: Add sysfs support for _HRV hardware revision
arm64: defconfig: Enable ACPI
ACPI / ARM64: Remove EXPERT dependency for ACPI on ARM64
ACPI / ARM64: Don't enable ACPI by default on ARM64
acer-wmi: Use acpi_dev_found()
eeepc-wmi: Use acpi_dev_found()
ACPI / utils: Rename acpi_dev_present()
* acpi-tools:
tools/power/acpi: close file only if it is open
Use shiny new link APIs to manage the links. Also remove old link
configuration logic from driver.
We need to keep link and cmd dma to off during active suspend
to allow system to enter low power state and turn it on if
the link and cmd dma was on before active suspend in active
resume.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Format number after 0x in hex.
Cc: Jie Yang <yang.jie@linux.intel.com>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds the Broxton-P machine driver for Intel Broxton-P
reference boards. This machine uses the RT298 codec
Signed-off-by: Ramesh Babu <ramesh.babu@intel.com>
Signed-off-by: Senthilnathan Veppur <senthilnathanx.veppur@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Broxton-P platform has 6 SSPs so we need to add ssp2 thru
ssp5 to DAI list for the driver.
Signed-off-by: Pardha Saradhi K <pardha.saradhi.kesapragada@intel.com>
Signed-off-by: Ramesh Babu <ramesh.babu@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
During skl_nhlt_init(), acpi obj pointer is allocated and never
freed and remap address is not unmapped.
To fix this we should release the ACPI obj and also unmap the
nhlt address during cleanup of driver.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
On WoV we can suspend the DMA and keep the DSP pipelines only On,
so remove the ignore_suspend for WoV streams but keep them for
WoV endpoints.
This helps in achieving better power by suspending DMAs
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For 'ignore_suspend' cases we need to keep DSP and pipes On, but
can suspend the stream and pause the DMA as we are not rendering
data during the suspended time.
For this we can check the dai widget ignore_suspend flag in
trigger suspend/resume, and start and stop the host DMA and host
copier pipelines.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If widget of a playback or capture DAI is already On, then no
need not send the Set DMA Control IPC message to firmware.
Signed-off-by: Dharageswari R <dharageswari.r@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
param_data variable is allocated during set module format of init
instance is not getting freed and hence can cause a memory leak.
So free it up.
Signed-off-by: Mousumi Jana <mousumix.jana@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If request firmware fails at init, the code loader DMA allocation
can be NULL, so check for boot complete before freeing up these
resources
Signed-off-by: Dharageswari R <dharageswari.r@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is a fairly large collection of fixes but almost all driver
specific ones, especially to the new Intel drivers which have had a lot
of recent development. The one core fix is a change to the debugfs code
to avoid crashes in some relatively unusual configurations.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXINZtAAoJECTWi3JdVIfQ+BwH/1eLqMfCSZM9nsDr1QMvOCDP
SO4ZoWqvYplBcS8pYKbJmqtuo8jMxT3VIQF+b5hPAVhgpLwMmy9qeFtatqCQ2WDC
GfCqW8LSKtrzwUwmoRrtHx7vfBLP1/z78F8ORQzwhrplTCBhvPLbUOrV51EFj6tf
Dfo2tW0uxww9iCZduYu4LadOhFOfuw+5shUrJk5A5f975Zbdgyke4CbRnlbDPXLq
d4i7bNfiISkSJiKMpdZFeiOQCd0+uXHh2WkMtVYSGVTA2Kf7d7HtX+JpEFFmaJgJ
8CndjgNJ1ZXtMHl1pMYmNqKJ5mEgmVtbGGJWY4QmQBva0EfQ+vLZt78BG3qvJwk=
=SXH2
-----END PGP SIGNATURE-----
Merge tag 'asoc-fix-v4.6-rc5' into asoc-intel
ASoC: Fixes for v4.6
This is a fairly large collection of fixes but almost all driver
specific ones, especially to the new Intel drivers which have had a lot
of recent development. The one core fix is a change to the debugfs code
to avoid crashes in some relatively unusual configurations.
We pass struct dw_dma_chip to dw_dma_probe() anyway, thus we may use it to
pass a platform data as well.
While here, constify the source of the platform data.
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Default channel map is set for 2 channels. Fix the channel map
based on runtime params to support multichannel.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Channel max is changed to 8 from stereo to support multichannel
capability for HDMI devices.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
HDMI registers channel map controls per PCM. As PCMs are not
registered during dai_link init callback, store the pcm ids and
codec DAIs during this init callback.
Register for late probe and call the jack_init API which also
registers channel map in the late probe callback handler.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
HDMI registers channel map controls per PCM. As PCMs are not
registered during dai_link init callback, store the pcm ids and
codec DAIs during this init callback.
Register for late probe and call the jack_init API which also
registers channel map in the late probe callback handler.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
HDMI registers channel map controls per PCM. As PCMs are not
registered during dai_link init callback, store the pcm ids and
codec DAIs during this init callback.
Register for late probe and call the jack_init API which also
registers channel map in the late probe callback handler.
The patch following the machine driver changes adds the channel
map control in the hdac_hdmi codec driver.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Users have reported seeing this false warning on atom driver
[ 5.647469] sst-mfld-platform sst-mfld-platform: Slot control: codec_out tx interleaver slot 0 doesn't have DAPM widget!!!
[ 5.661612] sst-mfld-platform sst-mfld-platform: Slot control: codec_out tx interleaver slot 1 doesn't have DAPM widget!!!
[ 5.661646] sst-mfld-platform sst-mfld-platform: Slot control: codec_out tx interleaver slot 2 doesn't have DAPM widget!!!
[ 5.661681] sst-mfld-platform sst-mfld-platform: Slot control: codec_out tx interleaver slot 3 doesn't have DAPM widget!!!
[ 5.661708] sst-mfld-platform sst-mfld-platform: Slot control: codec_in rx deinterleaver codec_in0_0 doesn't have DAPM widget!!!
[ 5.661738] sst-mfld-platform sst-mfld-platform: Slot control: codec_in rx deinterleaver codec_in0_1 doesn't have DAPM widget!!!
[ 5.661771] sst-mfld-platform sst-mfld-platform: Slot control: codec_in rx deinterleaver codec_in1_0 doesn't have DAPM widget!!!
[ 5.661807] sst-mfld-platform sst-mfld-platform: Slot control: codec_in rx deinterleaver codec_in1_1 doesn't have DAPM widget!!!
This is caused when check for control is not being associated
with a dapm widget, but the check is wrong as the else case
maybe triggered when widget is not powered up, so we should
check if widget is associated before printing this message.
Tested-by: Sandeep Tayal <sandeepx.tayal@intel.com>
Tested-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To avoid complex string manipulations with UUID in canonical
form, use UUID in binary format.
Signed-off-by: Shreyas NC <shreyas.nc@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The generic ID can be used by topology:
- Toplogy can create FE links and set their ID, machine drivers will
be notified and check this ID for machine-specific init.
- Toplogy can use the ID to find existing BE & CC links and further
configure them.
Signed-off-by: Mengdong Lin <mengdong.lin@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
FW expects sampling rate rounded up to next higher integer value
when calculating ibs/obs. For example for 44.1k, it should be
rounded up to 45 to calculate ibs/obs.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
acpi_dev_present() was originally named after pci_dev_present()
to signify the similarity of the two functions.
However Rafael J. Wysocki pointed out that the exported function
acpi_dev_present() is easily confused with the non-exported
acpi_device_is_present(). Additionally in ACPI parlance the term
"present" usually refers to the "device is present" bit returned
by the _STA control method, yet acpi_dev_present() merely checks
presence in the namespace. It does not invoke _STA at all, let
alone check the "device is present" bit.
As suggested by Rafael, rename the function to acpi_dev_found()
and adjust all existing call sites.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In the original code we ended the loop with tries set to -1 instead of
zero.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Broxton DSP is mostly similar to Skylake one but with subtle
differences like no Code Load DMA and uses HDA DMA for code
loading, DSP D0 and D3 sequences are different.
These changes are comprehended by adding different DSP power up
and down handlers, and new loader ops and also adding prepare and
trigger which HDA DSP DMA requires
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Jayachandran B <jayachandran.b@intel.com>
Signed-off-by: GuruprasadX Pawse <guruprasadx.pawse@intel.com>
Signed-off-by: Kranthi G <gudishax.kranthikumar@intel.com>
Signed-off-by: Dharageswari R <dharageswari.r@intel.com>
Signed-off-by: Ramesh Babu <ramesh.babu@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add function stub for "sst_acpi_find_name_from_hid()"
when CONFIG_ACPI is not enabled so that the driver will build
successfully. This fixes the following build errors:
(loadable module)
ERROR: "sst_acpi_find_name_from_hid" [sound/soc/intel/boards/snd-soc-sst-bytcr-rt5640.ko] undefined!
(or built-in)
bytcr_rt5640.c:(.text+0x26fc52): undefined reference to `sst_acpi_find_name_from_hid'
Reported-by: Borislav Petkov <bp@alien8.de>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
In PRE PMD of widget handler DSP resources are allocated after
the creation of DSP pipe and modules and in POST PMD DSP
resources are destroyed.
If there is any failure in pipe or module creation in PRE PMD,
pcm trigger fails and finally POST PMD gets called and DSP
resources are freed, without getting allocated.
Fixes the DSP resource de-allocation by allocating the resource
before creation of pipe and module in PRE PMD and in POST PMD,
free the resources.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Module needs to be unloaded only when it is loaded successfully.
To fix this, first correct the module state sequence and set module
state to LOADED if module is loaded successfully.
When unloading the module check if module state is not in UNINIT,
then unload it.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Skylake driver selects SND_HDA_I915 which causes kbuild to spew warning:
warning: (SND_SOC_INTEL_SKYLAKE) selects SND_HDA_I915 which has unmet direct dependencies
(SOUND && !M68K && !UML && SND && DRM_I915 && SND_HDA_CORE)
The SND_HDA_I915 should not be selected so drop that.
Reported-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The PCI bus takes pci_dev_get() and pci_dev_put() is also there.
So no need for drivers to invoke these. In SKL driver we were
calling pci_dev_put() only which is not right, so remove this
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Skylake driver uses i915 component APIs to talk to display.
On remove we should free up by invoking snd_hdac_i915_exit() but
that should be last thing in remove routine, so move it to last
in skl_free()
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In Skylake destructor we unmap the hardware address and then free
links and streams. The stream free accesses hardware to write to
registers and predictably causes oops.
So change the order and unmap last in destructor.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We are supposed to freeup the Code loader DMA allocation and
ensure all interrupts are disabled before we disable dsp cores.
So invoke these to ensure DSP shuts down properly.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
On driver removal we should ask the core to remove the device
objects as well, so invoke snd_hdac_ext_bus_device_remove() in
remove.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Broxton is an Intel SoC which sports a DSP and system is quite
like Skylake. So add this ID in Skylake driver
Signed-off-by: Senthilnathan Veppur <senthilnathanx.veppur@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The code loading for Skylake and other platforms is different, so
add a dsp_ops and a loader_ops which can be defined for each
platform.
Move the dsp init, cleanup and loader ops (alloc and free dma) to
these ops
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Broxton uses HDA DMA so needs to keep dmab in the driver context
so add it
Signed-off-by: GuruprasadX Pawse <guruprasadx.pawse@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The function skl_dsp_enable_core will be called by other parts of
driver so this can no longer be a static function.
Signed-off-by: Jayachandran B <jayachandran.b@intel.com>
Signed-off-by: GuruprasadX Pawse <guruprasadx.pawse@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some double whitespaces issues existed in driver, so fix them up.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The module ID defines are common to other platforms so can be
reused if moved to a common driver header so move it
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some CHT-T platforms make use of the Realtek RT5640 codec. Make use
of the machine driver developed for Baytrail.
Tested on Tronsmart Ara X5.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove hard-coded generation of codec name, use translation routine
to avoid issues with codec name not matching what the ACPI subsystem
registered
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
BIOS vendors sometimes declare multiple devices in the DSDT
table that all refer to the same HID. This is not very smart
but not illegal as long as only one device reports present with
the _STA method. The ACPI subsystem tracks each device with an
extension, e.g. 10EC5640:00 and 10EC5640:01
In the ASoC machine driver, the DAI codec name needs to refer to the
ACPI device that reported present, e.g. "i2c-10EC5640:01". The
extension will vary depending on how the BIOS is written and which
ACPI device is activated.
This patch adds a translation function that provides the codec
name from the ACPI HID to avoid any hard-coded values in the
machine driver.
Suggested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
BIOS vendors typically list multiple audio codecs in the DSDT
table and enable the relevant one by changing the return value
of the _STA method.
With the current code, all devices are reported by
acpi_dev_present(), regardless of the _STA return values. This
causes errors on probe with the wrong machine driver being loaded.
This patch essentially reverts 'commit 6f08cbdaac
("ASoC: Intel: Use acpi_dev_present()")' and adds code to
force the evaluation of the _STA method.
A better solution might be to make sure the ACPI subsystem only
reports devices with a _STA value of 0xf but apparently it's
problematic so dealing with this in the audio subsystem directly.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
