Conflicts:
drivers/net/usb/asix_common.c
net/ipv4/inet_connection_sock.c
net/switchdev/switchdev.c
In the inet_connection_sock.c case the request socket hashing scheme
is completely different in net-next.
The other two conflicts were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
The change made in the previous commit revealed a small flaw in the way
the node FSM is updated. When the function tipc_node_link_down() is
called for the last link to a node, we should check whether this was
caused by a local reset or by a received RESET message from the peer.
In the latter case, we can directly issue a PEER_LOST_CONTACT_EVT to
the node FSM, so that it is ready to re-establish contact. If this is
not done, the peer node will sometimes have to go through a second
establish cycle before the link becomes stable.
We fix this in this commit by conditionally issuing the mentioned
event in the function tipc_node_link_down(). We also move LINK_RESET
FSM even away from the link_reset() function and into the caller
function, partially because it is easier to follow the code when state
changes are gathered at a limited number of locations, partially
because there will be cases in future commits where we don't want the
link to go RESET mode when link_reset() is called.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a link is taken down because of a node local event, such as
disabling of a bearer or an interface, we currently leave it to the
peer node to discover the broken communication. The default time for
such failure discovery is 1.5-2 seconds.
If we instead allow the terminating link endpoint to send out a RESET
message at the moment it is reset, we can achieve the impression that
both endpoints are going down instantly. Since this is a very common
scenario, we find it worthwhile to make this small modification.
Apart from letting the link produce the said message, we also have to
ensure that the interface is able to transmit it before TIPC is
detached. We do this by performing the disabling of a bearer in three
steps:
1) Disable reception of TIPC packets from the interface in question.
2) Take down the links, while allowing them so send out a RESET message.
3) Disable transmission of TIPC packets on the interface.
Apart from this, we now have to react on the NETDEV_GOING_DOWN event,
instead of as currently the NEDEV_DOWN event, to ensure that such
transmission is possible during the teardown phase.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Link establishing, just like link teardown, is a non-atomic action, in
the sense that discovering that conditions are right to establish a link,
and the actual adding of the link to one of the node's send slots is done
in two different lock contexts. The link FSM is designed to help bridging
the gap between the two contexts in a safe manner.
We have now discovered a weakness in the implementaton of this FSM.
Because we directly let the link go from state LINK_ESTABLISHING to
state LINK_ESTABLISHED already in the first lock context, we are unable
to distinguish between a fully established link, i.e., a link that has
been added to its slot, and a link that has not yet reached the second
lock context. It may hence happen that a manual intervention, e.g., when
disabling an interface, causes the function tipc_node_link_down() to try
removing the link from the node slots, decrementing its active link
counter etc, although the link was never added there in the first place.
We solve this by delaying the actual state change until we reach the
second lock context, inside the function tipc_node_link_up(). This
makes it possible for potentail callers of __tipc_node_link_down() to
know if they should proceed or not, and the problem is solved.
Unforunately, the situation described above also has a second problem.
Since there by necessity is a tipc_node_link_up() call pending once
the node lock has been released, we must defuse that call by setting
the link back from LINK_ESTABLISHING to LINK_RESET state. This forces
us to make a slight modification to the link FSM, which will now look
as follows.
+------------------------------------+
|RESET_EVT |
| |
| +--------------+
| +-----------------| SYNCHING |-----------------+
| |FAILURE_EVT +--------------+ PEER_RESET_EVT|
| | A | |
| | | | |
| | | | |
| | |SYNCH_ |SYNCH_ |
| | |BEGIN_EVT |END_EVT |
| | | | |
| V | V V
| +-------------+ +--------------+ +------------+
| | RESETTING |<---------| ESTABLISHED |--------->| PEER_RESET |
| +-------------+ FAILURE_ +--------------+ PEER_ +------------+
| | EVT | A RESET_EVT |
| | | | |
| | +----------------+ | |
| RESET_EVT| |RESET_EVT | |
| | | | |
| | | |ESTABLISH_EVT |
| | | +-------------+ | |
| | | | RESET_EVT | | |
| | | | | | |
| V V V | | |
| +-------------+ +--------------+ RESET_EVT|
+--->| RESET |--------->| ESTABLISHING |<----------------+
+-------------+ PEER_ +--------------+
| A RESET_EVT |
| | |
| | |
|FAILOVER_ |FAILOVER_ |FAILOVER_
|BEGIN_EVT |END_EVT |BEGIN_EVT
| | |
V | |
+-------------+ |
| FAILINGOVER |<----------------+
+-------------+
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the previous commits, we are guaranteed that no packets
of type LINK_PROTOCOL or with illegal sequence numbers will be
attempted added to the link deferred queue. This makes it possible to
make some simplifications to the sorting algorithm in the function
tipc_skb_queue_sorted().
We also alter the function so that it will drop packets if one with
the same seqeunce number is already present in the queue. This is
necessary because we have identified weird packet sequences, involving
duplicate packets, where a legitimate in-sequence packet may advance to
the head of the queue without being detected and de-queued.
Finally, we make this function outline, since it will now be called only
in exceptional cases.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sequence number of an incoming packet is currently only checked
for less than, equality to, or bigger than the next expected number,
meaning that the receive window in practice becomes one half sequence
number cycle, or U16_MAX/2. This does not make sense, and may not even
be safe if there are extreme delays in the network. Any packet sent by
the peer during the ongoing cycle must belong inside his current send
window, or should otherwise be dropped if possible.
Since a link endpoint cannot know its peer's current send window, it
has to base this sanity check on a worst-case assumption, i.e., that
the peer is using a maximum sized window of 8191 packets. Using this
assumption, we now add a check that the sequence number is not bigger
than next_expected + TIPC_MAX_LINK_WIN. We also re-order the checks
done, so that the receive window test is performed before the gap test.
This way, we are guaranteed that no packet with illegal sequence numbers
are ever added to the deferred queue.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, all packets received in tipc_link_rcv() are unconditionally
added to the packet deferred queue, whereafter that queue is walked and
all its buffers evaluated for delivery. This is both non-optimal and
and makes the queue sorting function unnecessary complex.
This commit changes the loop so that an arrived packet is evaluated
first, and added to the deferred queue only when a sequence number gap
is discovered. A non-empty deferred queue is walked until it is empty
or until its head's sequence number doesn't fit.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During packet reception, the function tipc_link_rcv() adds its accepted
packets to a temporary buffer queue, before finally splicing this queue
into the lock protected input queue that will be delivered up to the
socket layer. The purpose is to reduce potential contention on the input
queue lock. However, since the vast majority of packets arrive in
sequence, they will anyway be added one by one to the input queue, and
the use of the temporary queue becomes a sub-optimization.
The only case where this queue makes sense is when unpacking buffers
from a bundle packet; here we want to avoid dozens of small buffers
to be added individually to the lock-protected input queue in a tight
loop.
In this commit, we remove the general usage of the temporary queue,
and keep it only for the packet unbundling case.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit e3eea1eb47 ("tipc: clean up handling of message priorities")
we introduced a field in the packet header for keeping track of the
priority of fragments, since this value is not present in the specified
protocol header. Since the value so far only is used at the transmitting
end of the link, we have not yet officially defined it as part of the
protocol.
Unfortunately, the field we use for keeping this value, bits 13-15 in
in word 5, has turned out to be a poor choice; it is already used by the
broadcast protocol for carrying the 'network id' field of the sending
node. Since packet fragments also need to be transported across the
broadcast protocol, the risk of conflict is obvious, and we see this
happen when we use network identities larger than 2^13-1. This has
escaped our testing because we have so far only been using small network
id values.
We now move this field to bits 0-2 in word 9, a field that is guaranteed
to be unused by all involved protocols.
Fixes: e3eea1eb47 ("tipc: clean up handling of message priorities")
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 6e498158a8 ("tipc: move link synch and failover to link aggregation level")
we introduced a new mechanism for performing link failover and
synchronization. We have now detected a bug in this mechanism.
During link synchronization we use the arrival of any packet on
the tunnel link to trig a check for whether it has reached the
synchronization point or not. This has turned out to be too
permissive, since it may cause an arriving non-last SYNCH packet to
end the synch state, just to see the next SYNCH packet initiate a
new synch state with a new, higher synch point. This is not fatal,
but should be avoided, because it may significantly extend the
synchronization period, while at the same time we are not allowed
to send NACKs if packets are lost. In the worst case, a low-traffic
user may see its traffic stall until a LINK_PROTOCOL state message
trigs the link to leave synchronization state.
At the same time, LINK_PROTOCOL packets which happen to have a (non-
valid) sequence number lower than the tunnel link's rcv_nxt value will
be consistently dropped, and will never be able to resolve the situation
described above.
We fix this by exempting LINK_PROTOCOL packets from the sequence number
check, as they should be. We also reduce (but don't completely
eliminate) the risk of entering multiple synchronization states by only
allowing the (logically) first SYNCH packet to initiate a synchronization
state. This works independently of actual packet arrival order.
Fixes: commit 6e498158a8 ("tipc: move link synch and failover to link aggregation level")
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The msg pointer into header may change after skb linearization.
We must reinitialize it after calling skb_linearize to prevent
operating on a freed or invalid pointer.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Reported-by: Tamás Végh <tamas.vegh@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If an attempt to wake up users of broadcast link is made when there is
no enough place in send queue than it may hang up inside the
tipc_sk_rcv() function since the loop breaks only after the wake up
queue becomes empty. This can lead to complete CPU stall with the
following message generated by RCU:
INFO: rcu_sched self-detected stall on CPU { 0} (t=2101 jiffies
g=54225 c=54224 q=11465)
Task dump for CPU 0:
tpch R running task 0 39949 39948 0x0000000a
ffffffff818536c0 ffff88181fa037a0 ffffffff8106a4be 0000000000000000
ffffffff818536c0 ffff88181fa037c0 ffffffff8106d8a8 ffff88181fa03800
0000000000000001 ffff88181fa037f0 ffffffff81094a50 ffff88181fa15680
Call Trace:
<IRQ> [<ffffffff8106a4be>] sched_show_task+0xae/0x120
[<ffffffff8106d8a8>] dump_cpu_task+0x38/0x40
[<ffffffff81094a50>] rcu_dump_cpu_stacks+0x90/0xd0
[<ffffffff81097c3b>] rcu_check_callbacks+0x3eb/0x6e0
[<ffffffff8106e53f>] ? account_system_time+0x7f/0x170
[<ffffffff81099e64>] update_process_times+0x34/0x60
[<ffffffff810a84d1>] tick_sched_handle.isra.18+0x31/0x40
[<ffffffff810a851c>] tick_sched_timer+0x3c/0x70
[<ffffffff8109a43d>] __run_hrtimer.isra.34+0x3d/0xc0
[<ffffffff8109aa95>] hrtimer_interrupt+0xc5/0x1e0
[<ffffffff81030d52>] ? native_smp_send_reschedule+0x42/0x60
[<ffffffff81032f04>] local_apic_timer_interrupt+0x34/0x60
[<ffffffff810335bc>] smp_apic_timer_interrupt+0x3c/0x60
[<ffffffff8165a3fb>] apic_timer_interrupt+0x6b/0x70
[<ffffffff81659129>] ? _raw_spin_unlock_irqrestore+0x9/0x10
[<ffffffff8107eb9f>] __wake_up_sync_key+0x4f/0x60
[<ffffffffa313ddd1>] tipc_write_space+0x31/0x40 [tipc]
[<ffffffffa313dadf>] filter_rcv+0x31f/0x520 [tipc]
[<ffffffffa313d699>] ? tipc_sk_lookup+0xc9/0x110 [tipc]
[<ffffffff81659259>] ? _raw_spin_lock_bh+0x19/0x30
[<ffffffffa314122c>] tipc_sk_rcv+0x2dc/0x3e0 [tipc]
[<ffffffffa312e7ff>] tipc_bclink_wakeup_users+0x2f/0x40 [tipc]
[<ffffffffa313ce26>] tipc_node_unlock+0x186/0x190 [tipc]
[<ffffffff81597c1c>] ? kfree_skb+0x2c/0x40
[<ffffffffa313475c>] tipc_rcv+0x2ac/0x8c0 [tipc]
[<ffffffffa312ff58>] tipc_l2_rcv_msg+0x38/0x50 [tipc]
[<ffffffff815a76d3>] __netif_receive_skb_core+0x5a3/0x950
[<ffffffff815a98d3>] __netif_receive_skb+0x13/0x60
[<ffffffff815a993e>] netif_receive_skb_internal+0x1e/0x90
[<ffffffff815aa138>] napi_gro_receive+0x78/0xa0
[<ffffffffa07f93f4>] tg3_poll_work+0xc54/0xf40 [tg3]
[<ffffffff81597c8c>] ? consume_skb+0x2c/0x40
[<ffffffffa07f9721>] tg3_poll_msix+0x41/0x160 [tg3]
[<ffffffff815ab0f2>] net_rx_action+0xe2/0x290
[<ffffffff8104b92a>] __do_softirq+0xda/0x1f0
[<ffffffff8104bc26>] irq_exit+0x76/0xa0
[<ffffffff81004355>] do_IRQ+0x55/0xf0
[<ffffffff8165a12b>] common_interrupt+0x6b/0x6b
<EOI>
The issue occurs only when tipc_sk_rcv() is used to wake up postponed
senders:
tipc_bclink_wakeup_users()
// wakeupq - is a queue which consists of special
// messages with SOCK_WAKEUP type.
tipc_sk_rcv(wakeupq)
...
while (skb_queue_len(inputq)) {
filter_rcv(skb)
// Here the type of message is checked
// and if it is SOCK_WAKEUP then
// it tries to wake up a sender.
tipc_write_space(sk)
wake_up_interruptible_sync_poll()
}
After the sender thread is woke up it can gather control and perform
an attempt to send a message. But if there is no enough place in send
queue it will call link_schedule_user() function which puts a message
of type SOCK_WAKEUP to the wakeup queue and put the sender to sleep.
Thus the size of the queue actually is not changed and the while()
loop never exits.
The approach I proposed is to wake up only senders for which there is
enough place in send queue so the described issue can't occur.
Moreover the same approach is already used to wake up senders on
unicast links.
I have got into the issue on our product code but to reproduce the
issue I changed a benchmark test application (from
tipcutils/demos/benchmark) to perform the following scenario:
1. Run 64 instances of test application (nodes). It can be done
on the one physical machine.
2. Each application connects to all other using TIPC sockets in
RDM mode.
3. When setup is done all nodes start simultaneously send
broadcast messages.
4. Everything hangs up.
The issue is reproducible only when a congestion on broadcast link
occurs. For example, when there are only 8 nodes it works fine since
congestion doesn't occur. Send queue limit is 40 in my case (I use a
critical importance level) and when 64 nodes send a message at the
same moment a congestion occurs every time.
Signed-off-by: Dmitry S Kolmakov <kolmakov.dmitriy@huawei.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent changes to the link synchronization means that we can now just
drop packets arriving on the synchronizing link before the synch point
is reached. This has lead to significant simplifications to the
implementation, but also turns out to have a flip side that we need
to consider.
Under unlucky circumstances, the two endpoints may end up
repeatedly dropping each other's packets, while immediately
asking for retransmission of the same packets, just to drop
them once more. This pattern will eventually be broken when
the synch point is reached on the other link, but before that,
the endpoints may have arrived at the retransmission limit
(stale counter) that indicates that the link should be broken.
We see this happen at rare occasions.
The fix for this is to not ask for retransmissions when a link is in
state LINK_SYNCHING. The fact that the link has reached this state
means that it has already received the first SYNCH packet, and that it
knows the synch point. Hence, it doesn't need any more packets until the
other link has reached the synch point, whereafter it can go ahead and
ask for the missing packets.
However, because of the reduced traffic on the synching link that
follows this change, it may now take longer to discover that the
synch point has been reached. We compensate for this by letting all
packets, on any of the links, trig a check for synchronization
termination. This is possible because the packets themselves don't
contain any information that is needed for discovering this condition.
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we introduced the new link failover/synch mechanism
in commit 6e498158a8
("tipc: move link synch and failover to link aggregation level"),
we missed the case when the non-tunnel link goes down during the link
synchronization period. In this case the tunnel link will remain in
state LINK_SYNCHING, something leading to unpredictable behavior when
the failover procedure is initiated.
In this commit, we ensure that the node and remaining link goes
back to regular communication state (SELF_UP_PEER_UP/LINK_ESTABLISHED)
when one of the parallel links goes down. We also ensure that we don't
re-enter synch mode if subsequent SYNCH packets arrive on the remaining
link.
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a link goes down, and there is still a working link towards its
destination node, a failover is initiated, and the failed link is not
allowed to re-establish until that procedure is finished. To ensure
this, the concerned link endpoints are set to state LINK_FAILINGOVER,
and the node endpoints to NODE_FAILINGOVER during the failover period.
However, if the link reset is due to a disabled bearer, the corres-
ponding link endpoint is deleted, and only the node endpoint knows
about the ongoing failover. Now, if the disabled bearer is re-enabled
during the failover period, the discovery mechanism may create a new
link endpoint that is ready to be established, despite that this is not
permitted. This situation may cause both the ongoing failover and any
subsequent link synchronization to fail.
In this commit, we ensure that a newly created link goes directly to
state LINK_FAILINGOVER if the corresponding node state is
NODE_FAILINGOVER. This eliminates the problem described above.
Furthermore, we tighten the criteria for which packets are allowed
to end a failover state in the function tipc_node_check_state().
By checking that the receiving link is up and running, instead of just
checking that it is not in failover mode, we eliminate the risk that
protocol packets from the re-created link may cause the failover to
be prematurely terminated.
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A zero length payload means that no TLV (Type Length Value) data has
been passed. Prior to this patch a non-existing TLV could be sanity
checked with TLV_OK() resulting in random behavior where a user
sending an empty message occasionally got a incorrect "operation not
supported" message back.
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds net argument to ipv6_stub_impl.ipv6_dst_lookup
for use cases where sk is not available (like mpls).
sk appears to be needed to get the namespace 'net' and is optional
otherwise. This patch series changes ipv6_stub_impl.ipv6_dst_lookup
to take net argument. sk remains optional.
All callers of ipv6_stub_impl.ipv6_dst_lookup have been modified
to pass net. I have modified them to use already available
'net' in the scope of the call. I can change them to
sock_net(sk) to avoid any unintended change in behaviour if sock
namespace is different. They dont seem to be from code inspection.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We simplify the link creation function tipc_link_create() and the way
the link struct it is connected to the node struct. In particular, we
remove the duplicate initialization of some fields which are anyway set
in tipc_link_reset().
Tested-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, when we extract small messages from a message bundle, or
when many messages have accumulated in the link arrival queue, those
messages are added one by one to the lock protected link input queue.
This may increase contention with the reader of that queue, in
the function tipc_sk_rcv().
This commit introduces a temporary, unprotected input queue in
tipc_link_rcv() for such cases. Only when the arrival queue has been
emptied, and the function is ready to return, does it splice the whole
temporary queue into the real input queue.
Tested-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the most recent changes, all access calls to a link which
may entail addition of messages to the link's input queue are
postpended by an explicit call to tipc_sk_rcv(), using a reference
to the correct queue.
This means that the potentially hazardous implicit delivery, using
tipc_node_unlock() in combination with a binary flag and a cached
queue pointer, now has become redundant.
This commit removes this implicit delivery mechanism both for regular
data messages and for binding table update messages.
Tested-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to facilitate future improvements to the locking structure, we
want to make resetting and establishing of links non-atomic. I.e., the
functions tipc_node_link_up() and tipc_node_link_down() should be called
from outside the node lock context, and grab/release the node lock
themselves. This requires that we can freeze the link state from the
moment it is set to RESETTING or PEER_RESET in one lock context until
it is set to RESET or ESTABLISHING in a later context. The recently
introduced link FSM makes this possible, so we are now ready to introduce
the above change.
This commit implements this.
Tested-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The node lock is currently grabbed and and released in the function
tipc_disc_rcv() in the file discover.c. As a preparation for the next
commits, we need to move this node lock handling, along with the code
area it is covering, to node.c.
This commit introduces this change.
Tested-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Until now, we have been handling link failover and synchronization
by using an additional link state variable, "exec_mode". This variable
is not independent of the link FSM state, something causing a risk of
inconsistencies, apart from the fact that it clutters the code.
The conditions are now in place to define a new link FSM that covers
all existing use cases, including failover and synchronization, and
eliminate the "exec_mode" field altogether. The FSM must also support
non-atomic resetting of links, which will be introduced later.
The new link FSM is shown below, with 7 states and 8 events.
Only events leading to state change are shown as edges.
+------------------------------------+
|RESET_EVT |
| |
| +--------------+
| +-----------------| SYNCHING |-----------------+
| |FAILURE_EVT +--------------+ PEER_RESET_EVT|
| | A | |
| | | | |
| | | | |
| | |SYNCH_ |SYNCH_ |
| | |BEGIN_EVT |END_EVT |
| | | | |
| V | V V
| +-------------+ +--------------+ +------------+
| | RESETTING |<---------| ESTABLISHED |--------->| PEER_RESET |
| +-------------+ FAILURE_ +--------------+ PEER_ +------------+
| | EVT | A RESET_EVT |
| | | | |
| | | | |
| | +--------------+ | |
| RESET_EVT| |RESET_EVT |ESTABLISH_EVT |
| | | | |
| | | | |
| V V | |
| +-------------+ +--------------+ RESET_EVT|
+--->| RESET |--------->| ESTABLISHING |<----------------+
+-------------+ PEER_ +--------------+
| A RESET_EVT |
| | |
| | |
|FAILOVER_ |FAILOVER_ |FAILOVER_
|BEGIN_EVT |END_EVT |BEGIN_EVT
| | |
V | |
+-------------+ |
| FAILINGOVER |<----------------+
+-------------+
These changes are fully backwards compatible.
Tested-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The implementation of the link FSM currently takes decisions about and
sends out link protocol messages. This is unnecessary, since such
actions are not the result of any link state change, and are even
decided based on non-FSM state information ("silent_intv_cnt").
We now move the sending of unicast link protocol messages to the
function tipc_link_timeout(), and the initial broadcast synchronization
message to tipc_node_link_up(). The latter is done because a link
instance should not need to know whether it is the first or second
link to a destination. Such information is now restricted to and
handled by the link aggregation layer in node.c
Tested-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Link failover and synchronization have until now been handled by the
links themselves, forcing them to have knowledge about and to access
parallel links in order to make the two algorithms work correctly.
In this commit, we move the control part of this functionality to the
link aggregation level in node.c, which is the right location for this.
As a result, the two algorithms become easier to follow, and the link
implementation becomes simpler.
Tested-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In many cases the call order when a link is reset goes as follows:
tipc_node_xx()->tipc_link_reset()->tipc_node_link_down()
This is not the right order if we want the node to be in control,
so in this commit we change the order to:
tipc_node_xx()->tipc_node_link_down()->tipc_link_reset()
The fact that tipc_link_reset() now is called from only one
location with a well-defined state will also facilitate later
simplifications of tipc_link_reset() and the link FSM.
Tested-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In line with our effort to let the node level have full control over
its links, we want to move all link reset calls from link.c to node.c.
Some of the calls can be moved by simply moving the calling function,
when this is the right thing to do. For the remaining calls we use
the now established technique of returning a TIPC_LINK_DOWN_EVT
flag from tipc_link_rcv(), whereafter we perform the reset call when
the call returns.
This change serves as a preparation for the coming commits.
Tested-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function tipc_link_activate() is redundant, since it mostly performs
settings that have already been done in a preceding tipc_link_reset().
There are three exceptions to this:
- The actual state change to TIPC_LINK_WORKING. This should anyway be done
in the FSM, and not in a separate function.
- Registration of the link with the bearer. This should be done by the
node, since we don't want the link to have any knowledge about its
specific bearer.
- Call to tipc_node_link_up() for user access registration. With the new
role distribution between link aggregation and link level this becomes
the wrong call order; tipc_node_link_up() should instead be called
directly as a result of a TIPC_LINK_UP event, hence by the node itself.
This commit implements those changes.
Tested-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit d999297c3d
("tipc: reduce locking scope during packet reception") we introduced
a new function tipc_build_bcast_sync_msg(), which carries initial
synchronization data between two nodes at first contact and at
re-contact. In this function, we missed to add synchronization data,
with the effect that the broadcast link endpoints will fail to
synchronize correctly at re-contact between a running and a restarted
node. All other cases work as intended.
With this commit, we fix this bug.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a message is received in a socket, one of the call chains
tipc_sk_rcv()->tipc_sk_enqueue()->filter_rcv()(->tipc_sk_proto_rcv())
or
tipc_sk_backlog_rcv()->filter_rcv()(->tipc_sk_proto_rcv())
are followed. At each of these levels we may encounter situations
where the message may need to be rejected, or a new message
produced for transfer back to the sender. Despite recent
improvements, the current code for doing this is perceived
as awkward and hard to follow.
Leveraging the two previous commits in this series, we now
introduce a more uniform handling of such situations. We
let each of the functions in the chain itself produce/reverse
the message to be returned to the sender, but also perform the
actual forwarding. This simplifies the necessary logics within
each function.
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, we use the code sequence
if (msg_reverse())
tipc_link_xmit_skb()
at numerous locations in socket.c. The preparation of arguments
for these calls, as well as the sequence itself, makes the code
unecessarily complex.
In this commit, we introduce a new function, tipc_sk_respond(),
that performs this call combination. We also replace some, but not
yet all, of these explicit call sequences with calls to the new
function. Notably, we let the function tipc_sk_proto_rcv() use
the new function to directly send out PROBE_REPLY messages,
instead of deferring this to the calling tipc_sk_rcv() function,
as we do now.
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The shortest TIPC message header, for cluster local CONNECTED messages,
is 24 bytes long. With this format, the fields "dest_node" and
"orig_node" are optimized away, since they in reality are redundant
in this particular case.
However, the absence of these fields leads to code inconsistencies
that are difficult to handle in some cases, especially when we need
to reverse or reject messages at the socket layer.
In this commit, we concentrate the handling of the absent fields
to one place, by letting the function tipc_msg_reverse() reallocate
the buffer and expand the header to 32 bytes when necessary. This
means that the socket code now can assume that the two previously
absent fields are present in the header when a message needs to be
rejected. This opens up for some further simplifications of the
socket code.
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit d999297c3d
("tipc: reduce locking scope during packet reception") we introduced
a new function tipc_link_proto_rcv(). This function contains a bug,
so that it sometimes by error sends out a non-zero link priority value
in created protocol messages.
The bug may lead to an extra link reset at initial link establising
with older nodes. This will never happen more than once, whereafter
the link will work as intended.
We fix this bug in this commit.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We convert packet/message reception according to the same principle
we have been using for message sending and timeout handling:
We move the function tipc_rcv() to node.c, hence handling the initial
packet reception at the link aggregation level. The function grabs
the node lock, selects the receiving link, and accesses it via a new
call tipc_link_rcv(). This function appends buffers to the input
queue for delivery upwards, but it may also append outgoing packets
to the xmit queue, just as we do during regular message sending. The
latter will happen when buffers are forwarded from the link backlog,
or when retransmission is requested.
Upon return of this function, and after having released the node lock,
tipc_rcv() delivers/tranmsits the contents of those queues, but it may
also perform actions such as link activation or reset, as indicated by
the return flags from the link.
This reduces the number of cpu cycles spent inside the node spinlock,
and reduces contention on that lock.
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The logics for determining when a node is permitted to establish
and maintain contact with its peer node becomes non-trivial in the
presence of multiple parallel links that may come and go independently.
A known failure scenario is that one endpoint registers both its links
to the peer lost, cleans up it binding table, and prepares for a table
update once contact is re-establihed, while the other endpoint may
see its links reset and re-established one by one, hence seeing
no need to re-synchronize the binding table. To avoid this, a node
must not allow re-establishing contact until it has confirmation that
even the peer has lost both links.
Currently, the mechanism for handling this consists of setting and
resetting two state flags from different locations in the code. This
solution is hard to understand and maintain. A closer analysis even
reveals that it is not completely safe.
In this commit we do instead introduce an FSM that keeps track of
the conditions for when the node can establish and maintain links.
It has six states and four events, and is strictly based on explicit
knowledge about the own node's and the peer node's contact states.
Only events leading to state change are shown as edges in the figure
below.
+--------------+
| SELF_UP/ |
+---------------->| PEER_COMING |-----------------+
SELF_ | +--------------+ |PEER_
ESTBL_ | | |ESTBL_
CONTACT| SELF_LOST_CONTACT | |CONTACT
| v |
| +--------------+ |
| PEER_ | SELF_DOWN/ | SELF_ |
| LOST_ +--| PEER_LEAVING |<--+ LOST_ v
+-------------+ CONTACT | +--------------+ | CONTACT +-----------+
| SELF_DOWN/ |<----------+ +----------| SELF_UP/ |
| PEER_DOWN |<----------+ +----------| PEER_UP |
+-------------+ SELF_ | +--------------+ | PEER_ +-----------+
| LOST_ +--| SELF_LEAVING/|<--+ LOST_ A
| CONTACT | PEER_DOWN | CONTACT |
| +--------------+ |
| A |
PEER_ | PEER_LOST_CONTACT | |SELF_
ESTBL_ | | |ESTBL_
CONTACT| +--------------+ |CONTACT
+---------------->| PEER_UP/ |-----------------+
| SELF_COMING |
+--------------+
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In our effort to move control of the links to the link aggregation
layer, we move the perodic link supervision timer to struct tipc_node.
The new timer is shared between all links belonging to the node, thus
saving resources, while still kicking the FSM on both its pertaining
links at each expiration.
The current link timer and corresponding functions are removed.
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We create a second, simpler, link timer function, tipc_link_timeout().
The new function makes use of the new FSM function introduced in the
previous commit, and just like it, takes a buffer queue as parameter.
It returns an event bit field and potentially a link protocol packet
to the caller.
The existing timer function, link_timeout(), is still needed for a
while, so we redesign it to become a wrapper around the new function.
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The link FSM implementation is currently unnecessarily complex.
It sometimes checks for conditional state outside the FSM data
before deciding next state, and often performs actions directly
inside the FSM logics.
In this commit, we create a second, simpler FSM implementation,
that as far as possible acts only on states and events that it is
strictly defined for, and postpone any actions until it is finished
with its decisions. It also returns an event flag field and an a
buffer queue which may potentially contain a protocol message to
be sent by the caller.
Unfortunately, we cannot yet make the FSM "clean", in the sense
that its decisions are only based on FSM state and event, and that
state changes happen only here. That will have to wait until the
activate/reset logics has been cleaned up in a future commit.
We also rename the link states as follows:
WORKING_WORKING -> TIPC_LINK_WORKING
WORKING_UNKNOWN -> TIPC_LINK_PROBING
RESET_UNKNOWN -> TIPC_LINK_RESETTING
RESET_RESET -> TIPC_LINK_ESTABLISHING
The existing FSM function, link_state_event(), is still needed for
a while, so we redesign it to make use of the new function.
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a preparation for later changes, we introduce a new function
tipc_link_build_proto_msg(). Instead of actually sending the created
protocol message, it only creates it and adds it to the head of a
skb queue provided by the caller.
Since we still need the existing function tipc_link_protocol_xmit()
for a while, we redesign it to make use of the new function.
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The status flag LINK_STOPPED is not needed any more, since the
mechanism for delayed deletion of links has been removed.
Likewise, LINK_STARTED and LINK_START_EVT are unnecessary,
because we can just as well start the link timer directly from
inside tipc_link_create().
We eliminate these flags in this commit.
Instead of the above flags, we now introduce three new link modes,
TIPC_LINK_OPEN, TIPC_LINK_BLOCKED and TIPC_LINK_TUNNEL. The values
indicate whether, and in the case of TIPC_LINK_TUNNEL, which, messages
the link is allowed to receive in this state. TIPC_LINK_BLOCKED also
blocks timer-driven protocol messages to be sent out, and any change
to the link FSM. Since the modes are mutually exclusive, we convert
them to state values, and rename the 'flags' field in struct tipc_link
to 'exec_mode'.
Finally, we move the #defines for link FSM states and events from link.h
into enums inside the file link.c, which is the real usage scope of
these definitions.
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, message sending is performed through a deep call chain,
where the node spinlock is grabbed and held during a significant
part of the transmission time. This is clearly detrimental to
overall throughput performance; it would be better if we could send
the message after the spinlock has been released.
In this commit, we do instead let the call revert on the stack after
the buffer chain has been added to the transmission queue, whereafter
clones of the buffers are transmitted to the device layer outside the
spinlock scope.
As a further step in our effort to separate the roles of the node
and link entities we also move the function tipc_link_xmit() to
node.c, and rename it to tipc_node_xmit().
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the function tipc_link_xmit() is given a buffer list for
transmission, it currently consumes the list both when transmission
is successful and when it fails, except for the special case when
it encounters link congestion.
This behavior is inconsistent, and needs to be corrected if we want
to avoid problems in later commits in this series.
In this commit, we change this to let the function consume the list
only when transmission is successful, and leave the list with the
sender in all other cases. We also modifiy the socket code so that
it adapts to this change, i.e., purges the list when a non-congestion
error code is returned.
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
struct tipc_node currently holds two arrays of link pointers; one,
indexed by bearer identity, which contains all links irrespective of
current state, and one two-slot array for the currently active link
or links. The latter array contains direct pointers into the elements
of the former. This has the effect that we cannot know the bearer id of
a link when accessing it via the "active_links[]" array without actually
dereferencing the pointer, something we want to avoid in some cases.
In this commit, we do instead store the bearer identity in the
"active_links" array, and use this as an index to find the right element
in the overall link entry array. This change should be seen as a
preparation for the later commits in this series.
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At present, the link input queue and the name distributor receive
queues are fields aggregated in struct tipc_link. This is a hazard,
because a link might be deleted while a receiving socket still keeps
reference to one of the queues.
This commit fixes this bug. However, rather than adding yet another
reference counter to the critical data path, we move the two queues
to safe ground inside struct tipc_node, which is already protected, and
let the link code only handle references to the queues. This is also
in line with planned later changes in this area.
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a step towards turning links into node internal entities, we move the
creation of links from the neighbor discovery logics to the node's link
control logics.
We also create an additional entry for the link's media address in the
newly introduced struct tipc_link_entry, since this is where it is
needed in the upcoming commits. The current copy in struct tipc_link
is kept for now, but will be removed later.
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
struct 'tipc_node' currently contains two arrays for link attributes,
one for the link pointers, and one for the usable link MTUs.
We now group those into a new struct 'tipc_link_entry', and intoduce
one single array consisting of such enties. Apart from being a cosmetic
improvement, this is a starting point for the strict master-slave
relation between node and link that we will introduce in the following
commits.
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calling connect() with an AF_TIPC socket would trigger a series
of error messages from SELinux along the lines of:
SELinux: Invalid class 0
type=AVC msg=audit(1434126658.487:34500): avc: denied { <unprintable> }
for pid=292 comm="kworker/u16:5" scontext=system_u:system_r:kernel_t:s0
tcontext=system_u:object_r:unlabeled_t:s0 tclass=<unprintable>
permissive=0
This was due to a failure to initialize the security state of the new
connection sock by the tipc code, leaving it with junk in the security
class field and an unlabeled secid. Add a call to security_sk_clone()
to inherit the security state from the parent socket.
Reported-by: Tim Shearer <tim.shearer@overturenetworks.com>
Signed-off-by: Stephen Smalley <sds@tycho.nsa.gov>
Acked-by: Paul Moore <paul@paul-moore.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 1f66d161ab
("tipc: introduce starvation free send algorithm")
we introduced a counter per priority level for buffers
in the link backlog queue. We also introduced a new
function tipc_link_purge_backlog(), to reset these
counters to zero when the link is reset.
Unfortunately, we missed to call this function when
the broadcast link is reset, with the result that the
values of these counters might be permanently skewed
when new nodes are attached. This may in the worst case
lead to permananent, but spurious, broadcast link
congestion, where no broadcast packets can be sent at
all.
We fix this bug with this commit.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
