r8169_get_mac_version crashes when it meets an unknown MAC
due to tp->pci_dev not being set. Initialize it early.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
When we add the generic napi_disable_pending() breakout
logic to net_rx_action() it means that napi_disable()
can cause NAPI poll interrupt events to be disabled.
And this is exactly what we want. If a napi_disable()
is pending, and we are looping in the ->poll(), we want
->poll() event interrupts to stay disabled and we want
to complete the NAPI poll ASAP.
When ->poll() break out during device down was being handled on a
per-driver basis, often these drivers would turn interrupts back on
when '!netif_running()' was detected.
And this would just cause a reschedule of the NAPI ->poll() in the
interrupt handler before the napi_disable() could get in there and
grab the NAPI_STATE_SCHED bit.
The vast majority of drivers don't care if napi_disable() might have
the side effect of disabling NAPI ->poll() event interrupts. In all
such cases, when a napi_disable() is performed, the driver just
disabled interrupts or is about to.
However there were three exceptions to this in PCNET32, R8169, and
SKY2. To fix those cases, at the subsequent napi_enable() points, I
added code to ensure that the ->poll() interrupt events are enabled in
the hardware.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Don Fry <pcnet32@verizon.net>
Oops.
The current code does not like being given an u16 with the highest
bit set as an argument to mdio_write. Let's enforce a correct range of
values for both the register address and value (resp. 5 and 16 bits).
The callers are currently left as-is.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
RTL_GIGA_MAC_VER_17 breaks as well.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
Various symptoms depending on the .config options:
- the card stops working after some (short) time
- the card does not work at all
- the card disappears (nothing in lspci/dmesg)
A real power-off is needed to recover the card.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
The 8168c and the 8100e choke on it. I have not seen an indication
nor received a report that the TBI is being actively used on the
remaining 8168b and 8110. Let's disable it for now until someone
complains.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Matthias Winkler <m.winkler@unicon-ka.de>
Cc: Maarten Vanraes <maarten.vanraes@gmail.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
Disabling napi polling early is well enough.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
Don't call napi_disable if not configured and make sure that any
misuse of napi_xxx in future fails with a compile error.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
Realtek's r8168 driver version 8.003.00 adds new init sequences
(they do not appear in version 8.002.00).
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
The values have been updated between version 8.002.00 and version
8.003.00 of Realtek's r8168 driver. This modification syncs the
8168C with version 8.003.00.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
Consistent use of hexadecimal. No change of behavior otherwise.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
The values have been extracted from Realtek's r8168 driver
version 8.002.00.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
The code is reworked to easily add phy-dependant init changes.
No change of behavior should be noticed.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
The identifiers have been extracted from Realtek's drivers:
- version 8.002.00 of the r8168 driver
- version 6.002.00 of the r8169 driver
- version 1.002.00 of the r8101 driver
1. RTL_GIGA_MAC_VER_17 (8168Bf) is isolated from RTL_GIGA_MAC_VER_12 (8168Be)
Both are still handled the same in rtl8169_set_speed_xmii and in
rtl_set_rx_mode to avoid changes of behavior in this patch.
2. RTL_GIGA_MAC_VER_16 (8101Ec) is isolated from RTL_GIGA_MAC_VER_13 (8101Eb)
Same thing as above with relation to rtl8169_set_speed_xmii,
rtl_set_rx_mode and rtl_hw_start_8101.
3. The remaining new identifiers should not hurt.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
It is currently limited to the tested 0x8136 and 0x8168. 8169sb/8110sb ought
to handle it as well where they support MSI.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
Tester-Cc: Rolf Eike Beer <eike-kernel@sf-tec.de>
- prefix dprintk with KERN_DEBUG
- fix a bug with existing use of dprintk (PFX KERN_INFO PFX)
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
These have been superceded by the new ->get_sset_count() hook.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the operations
get-tx-csum
get-sg
get-tso
get-ufo
the default ethtool_op_xxx behavior is fine for all drivers, so we
permit op==NULL to imply the default behavior.
This provides a more uniform behavior across all drivers, eliminating
ethtool(8) "ioctl not supported" errors on older drivers that had
not been updated for the latest sub-ioctls.
The ethtool_op_xxx() functions are left exported, in case anyone
wishes to call them directly from a driver-private implementation --
a not-uncommon case. Should an ethtool_op_xxx() helper remain unused
for a while, except by net/core/ethtool.c, we can un-export it at a
later date.
[ Resolved conflicts with set/get value ethtool patch... -DaveM ]
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's been a useless no-op for long enough in 2.6 so I figured it's time to
remove it. The number of people that could object because they're
maintaining unified 2.4 and 2.6 drivers is probably rather small.
[ Handled drivers added by netdev tree and some missed IRDA cases... -DaveM ]
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several devices have multiple independant RX queues per net
device, and some have a single interrupt doorbell for several
queues.
In either case, it's easier to support layouts like that if the
structure representing the poll is independant from the net
device itself.
The signature of the ->poll() call back goes from:
int foo_poll(struct net_device *dev, int *budget)
to
int foo_poll(struct napi_struct *napi, int budget)
The caller is returned the number of RX packets processed (or
the number of "NAPI credits" consumed if you want to get
abstract). The callee no longer messes around bumping
dev->quota, *budget, etc. because that is all handled in the
caller upon return.
The napi_struct is to be embedded in the device driver private data
structures.
Furthermore, it is the driver's responsibility to disable all NAPI
instances in it's ->stop() device close handler. Since the
napi_struct is privatized into the driver's private data structures,
only the driver knows how to get at all of the napi_struct instances
it may have per-device.
With lots of help and suggestions from Rusty Russell, Roland Dreier,
Michael Chan, Jeff Garzik, and Jamal Hadi Salim.
Bug fixes from Thomas Graf, Roland Dreier, Peter Zijlstra,
Joseph Fannin, Scott Wood, Hans J. Koch, and Michael Chan.
[ Ported to current tree and all drivers converted. Integrated
Stephen's follow-on kerneldoc additions, and restored poll_list
handling to the old style to fix mutual exclusion issues. -DaveM ]
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 8169/8110SC currently announces itself as:
[...]
eth0: RTL8169sc/8110sc at 0x........, ..:..:..:..:..:.., XID 18000000 IRQ ..
^^^^^^^^
It uses RTL_GIGA_MAC_VER_05 and this part of the changeset can cut
its performance by a factor of 2~2.5 as reported by Timo.
(the driver includes code just before the hunk to write the ChipCmd
register when mac_version == RTL_GIGA_MAC_VER_0[1-4])
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Timo Jantunen <jeti@welho.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The 8168 ignores the requests to fetch the Tx descriptors when
the relevant TxPoll bit is already set. It easily kills the
performances of the 8168. David Gundersen has noticed that it
is enough to wait for the completion of the DMA transfer (NPQ
bit is cleared) before writing the TxPoll register again.
The extra IO traffic added by the proposed workaround could be
minimalized but it is not a high-priority task.
Fix for:
http://bugzilla.kernel.org/show_bug.cgi?id=7924http://bugzilla.kernel.org/show_bug.cgi?id=8688
(http://bugzilla.kernel.org/show_bug.cgi?id=7555 ?)
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: David Gundersen <gundy@iinet.net.au>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
The phys of the 8110SC (RTL_GIGA_MAC_VER_{05/06}) act abnormally in
gigabit mode if they are applied the parameters in rtl8169_hw_phy_config
which actually aim the 8110S/SB.
It is ok to return early from rtl8169_hw_phy_config as it does not
apply to the 8101 and 8168 families.
Signed-off-by: Edward Hsu <edward_hsu@realtek.com.tw>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Theory : though needless, it should not have hurt.
Practice: it does not play nice with DEBUG_SHIRQ + LOCKDEP + UP
(see https://bugzilla.redhat.com/bugzilla/show_bug.cgi?id=242572).
The patch makes sense in itself but I should dig why it has an effect
on #242572 (assuming that NAPI do not change in a near future).
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
Fix extracted from Realtek's driver (8.002.00/20070713) for the PHY
attached to 8111/8168b chipsets.
The check against mac_version is just usual paranoia during the bugfix
period of the kernel cycle. -- FR
Tested on Asus M2A-VM motherboard by Roger So.
No regression on my Asrock 945G DVI either (built-in 8168 + 2x8169).
Signed-off-by: Roger So <roger.so@gmail.com>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
All drivers implement ethtool get_perm_addr the same way -- by calling
the generic function. So we can inline the generic function into the
caller and avoid going through the drivers.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mark variables in drivers/* with uninitialized_var() if such a warning
appears, and analysis proves that the var is initialized properly on all
paths it is used.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
It does not really make sense to update the RX config register
before the mac filtering registers.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
Merged from Realtek's r8169-6.001 driver.
I have added some locking to protect against the arp monitoring
timer in the bonding driver. Accessing the configuration registers
is otherwise performed under RTNL locking.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
It does not cost much and it will ease the identification of (so far)
unknown devices.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
Align the IP header when the chipset can DMA at any location (plain 0x8169).
Otherwise (0x8136/0x8168) obey the constraint imposed by the hardware.
This patch complements the previous alignment rework done for copybreak.
Original idea from Philip Craig <philipc@snapgear.com>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Philip Craig <philipc@snapgear.com>
Cc: Mike Isely <isely@pobox.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
No functionnal change:
- trim the old history log
- whitespace/indent/case police
- unsigned int where signedness does not matter
- removal of obsolete assert
- needless cast from void * (dev_instance)
- remove dead code once related to power management
- use netdev_alloc_skb.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Stephen Hemminger <shemminger@linux-foundation.org>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
It has been documented as deprecated:
- in MODULE_PARM_DESC since may 2005 ;
- at the top of the source file and in printk since june 2004.
Good bye.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
The rx copybreak part is straightforward.
The align field in struct rtl_cfg_info is related to the alignment
requirements of the DMA operation. Its value is set at 2 to limit the
scale of possible regression but my old v1.21 8169 datasheet claims a
8 bytes requirements (which never appeared in the driver, of course)
and the 8101/8168 go with a plain 8 bytes alignment.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
This one includes:
- more tweaks to rtl_hw_start_8168
- a work around for a Rx FiFO overflow issue on the 8168Bb
- rtl8169_{intr_mask/napi_event} are replaced with per-device fields,
namely tp->{intr/napi}_event
- rtl_cfg_info is converted to C99 for readability but the values are
not changed for the 8169/8110 and the 8101
Includes ChipCmd fix from Bernhard Walle <bwalle@suse.de> (2007/02/24).
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
- new identifier for the 8110SCe
- the PCI latency timer is set unconditionally. This part is identical
in Realtek's r8168 (8.001.00) and r8101 (1.001.00)
- initialization of the cache line size register is for the 8169s only
- more magic in rtl_hw_start_8169
- it is not possible to factor out the setting of the the irq event mask
with the 8168 and the 8101 any more. Pushed it into the hw_start handler.
- rtl_set_rx_tx_config_registers() and write to the ChipCmd register are
issued identically for the whole 8169/8110 family: the 8110SCd/8110SCe
are handled the same way
- work around for AMD platform.
Some registers definitions in Realtek's driver are let aside for later.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
Same thing as the previous change for rtl_hw_start_8168.
The 8101 related code in rtl_hw_start_8169 (see RTL_GIGA_MAC_VER_13)
goes away.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
rtl_hw_start_8168 inherits the content of rtl_hw_start_8169 minus
the code which depends on RTL_GIGA_MAC_VER_XY (XY != {11/12}).
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
They aim to limit the amount of moved code when the hw_start
handler gets more specialized.
No functional change.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
Rationale: rtl8169_hw_start will not help maintaining an unified
driver for different chipsets but people at Realtek are probably
too polite to say it distinctly.
Let's add the hook and keep hw_start handler unchanged.
As can be seen from the content of rtl8169_pci_tbl, the RTL_CFG_1
entry in rtl_cfg_info was unused. I recycled it for the 0x8168.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
- pci_dma_sync_single_for_cpu is not needed for a single large packet
- remove the function pointer to help gcc optimizing the inline
pci_dma functions.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
It hasn't "summed" anything in over 7 years, and it's
just a straight mempcy ala skb_copy_to_linear_data()
so just get rid of it.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
The former style suggests a modulo arithmetic misuse but
the expression should never be < 0. Even if it does, the
driver will simply loop longer than expected (not that
the remaining parts of the system will necessarily
appreciate it...).
Let's warn the user when something goes wrong and try
to go over it.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
Use netdev_alloc_skb and remove the useless sk_buff * argument of
rtl8169_alloc_rx_skb.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
Many drivers had code that did kill_vid, but they weren't doing vlan
filtering. With new API the stub is unneeded unless device sets
NETIF_F_HW_VLAN_FILTER.
Bad habit: I couldn't resist fixing a couple of nearby style things
in acenic, and forcedeth.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
One less thing for drivers writers to worry about.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PM hooks are no-op if the r8169 interface is down (i.e. !IFF_UP).
However, as the chipset is enabled, the device will not work after a
suspend/resume cycle. The patch always issue the required PCI suspend
sequence and removes the module unload/reload workaround.
Signed-off-by: Arnaud Patard <apatard@mandriva.com>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The irq handler schedules a NAPI poll request unconditionally as soon as
the status register is not clean. It has been there - and wrong - for
ages but a recent timing change made it apparently easier to trigger.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Jay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Initialize the timer with the rest of the private-struct.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Added during bf793295e1
The current code requests a reset but prohibits autoneg, 1000 Mb/s,
100 Mb/s and full duplex. The 8168 does not like it at all.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch splits the vlan_group struct into a multi-allocated struct. On
x86_64, the size of the original struct is a little more than 32KB, causing
a 4-order allocation, which is prune to problems caused by buddy-system
external fragmentation conditions.
I couldn't just use vmalloc() because vfree() cannot be called in the
softirq context of the RCU callback.
Signed-off-by: Dan Aloni <da-x@monatomic.org>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
flush_scheduled_work() in net_device->close has a slight tendency
to deadlock with tasks on the workqueue that hold RTNL.
rtl8169_close/down simply need the recovery tasks to not meddle
with the hardware while the device is going down.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Checked in Realtek's driver, this one has no business being there.
The driver still works but there is a noticeable performance drop.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
The former option is removed and platform code can now specify the
expected behavior.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Conflicts:
drivers/infiniband/core/iwcm.c
drivers/net/chelsio/cxgb2.c
drivers/net/wireless/bcm43xx/bcm43xx_main.c
drivers/net/wireless/prism54/islpci_eth.c
drivers/usb/core/hub.h
drivers/usb/input/hid-core.c
net/core/netpoll.c
Fix up merge failures with Linus's head and fix new compilation failures.
Signed-Off-By: David Howells <dhowells@redhat.com>
Two thirds of packets are lost because of misalignment. Users of
Asus laptop did apparently not notice it.
Reported on Gigabyte GA-945GM-S2.
Fix for http://bugzilla.kernel.org/show_bug.cgi?id=7517
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
The 8110SB based n2100 board signals a lot of what ought to be
PCI data parity errors durint operation of the 8169 as target.
Experiment proved that the driver can ignore the error and
process the packet as if nothing had happened.
Let's add an ad-hoc knob to enable users to fix their system while
avoiding the risks of a wholesale change.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Mostly taken from Realtek's driver.
It's a bit yucky but the original is even worse.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Darren Salt <linux@youmustbejoking.demon.co.uk>
Realtek's 8139/810x (0x8136) PCI-E comes with a touchy PHY.
A big heavy reset seems to calm it down.
Fix for http://bugzilla.kernel.org/show_bug.cgi?id=7378.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Darren Salt <linux@youmustbejoking.demon.co.uk>
This changes the type of variable "i" in rtl8169_init_one()
from "unsigned int" to "int". "i" is checked for < 0 later,
which can never happen for "unsigned". This results in broken
error handling.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This reverts commit a2b98a697f.
As per Guennadi Liakhovetski, the mac address change support code breaks
some normal uses (_without_ any address changes), and until it's all
sorted out, we're better off without it.
Says Francois:
"Go revert it.
Despite what I claimed, I can not find a third-party confirmation by
email that it works elsewhere.
It would probably be enough to remove the call to
__rtl8169_set_mac_addr() in rtl8169_hw_start() though."
See also
http://bugzilla.kernel.org/show_bug.cgi?id=6032
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Maintain a per-CPU global "struct pt_regs *" variable which can be used instead
of passing regs around manually through all ~1800 interrupt handlers in the
Linux kernel.
The regs pointer is used in few places, but it potentially costs both stack
space and code to pass it around. On the FRV arch, removing the regs parameter
from all the genirq function results in a 20% speed up of the IRQ exit path
(ie: from leaving timer_interrupt() to leaving do_IRQ()).
Where appropriate, an arch may override the generic storage facility and do
something different with the variable. On FRV, for instance, the address is
maintained in GR28 at all times inside the kernel as part of general exception
handling.
Having looked over the code, it appears that the parameter may be handed down
through up to twenty or so layers of functions. Consider a USB character
device attached to a USB hub, attached to a USB controller that posts its
interrupts through a cascaded auxiliary interrupt controller. A character
device driver may want to pass regs to the sysrq handler through the input
layer which adds another few layers of parameter passing.
I've build this code with allyesconfig for x86_64 and i386. I've runtested the
main part of the code on FRV and i386, though I can't test most of the drivers.
I've also done partial conversion for powerpc and MIPS - these at least compile
with minimal configurations.
This will affect all archs. Mostly the changes should be relatively easy.
Take do_IRQ(), store the regs pointer at the beginning, saving the old one:
struct pt_regs *old_regs = set_irq_regs(regs);
And put the old one back at the end:
set_irq_regs(old_regs);
Don't pass regs through to generic_handle_irq() or __do_IRQ().
In timer_interrupt(), this sort of change will be necessary:
- update_process_times(user_mode(regs));
- profile_tick(CPU_PROFILING, regs);
+ update_process_times(user_mode(get_irq_regs()));
+ profile_tick(CPU_PROFILING);
I'd like to move update_process_times()'s use of get_irq_regs() into itself,
except that i386, alone of the archs, uses something other than user_mode().
Some notes on the interrupt handling in the drivers:
(*) input_dev() is now gone entirely. The regs pointer is no longer stored in
the input_dev struct.
(*) finish_unlinks() in drivers/usb/host/ohci-q.c needs checking. It does
something different depending on whether it's been supplied with a regs
pointer or not.
(*) Various IRQ handler function pointers have been moved to type
irq_handler_t.
Signed-Off-By: David Howells <dhowells@redhat.com>
(cherry picked from 1b16e7ac850969f38b375e511e3fa2f474a33867 commit)
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6: (217 commits)
net/ieee80211: fix more crypto-related build breakage
[PATCH] Spidernet: add ethtool -S (show statistics)
[NET] GT96100: Delete bitrotting ethernet driver
[PATCH] mv643xx_eth: restrict to 32-bit PPC_MULTIPLATFORM
[PATCH] Cirrus Logic ep93xx ethernet driver
r8169: the MMIO region of the 8167 stands behin BAR#1
e1000, ixgb: Remove pointless wrappers
[PATCH] Remove powerpc specific parts of 3c509 driver
[PATCH] s2io: Switch to pci_get_device
[PATCH] gt96100: move to pci_get_device API
[PATCH] ehea: bugfix for register access functions
[PATCH] e1000 disable device on PCI error
drivers/net/phy/fixed: #if 0 some incomplete code
drivers/net: const-ify ethtool_ops declarations
[PATCH] ethtool: allow const ethtool_ops
[PATCH] sky2: big endian
[PATCH] sky2: fiber support
[PATCH] sky2: tx pause bug fix
drivers/net: Trim trailing whitespace
[PATCH] ehea: IBM eHEA Ethernet Device Driver
...
Manually resolved conflicts in drivers/net/ixgb/ixgb_main.c and
drivers/net/sky2.c related to CHECKSUM_HW/CHECKSUM_PARTIAL changes by
commit 84fa7933a3 that just happened to be
next to unrelated changes in this update.
Replace CHECKSUM_HW by CHECKSUM_PARTIAL (for outgoing packets, whose
checksum still needs to be completed) and CHECKSUM_COMPLETE (for
incoming packets, device supplied full checksum).
Patch originally from Herbert Xu, updated by myself for 2.6.18-rc3.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Inverting the write ordering of the TxDescAddr{High/Low} registers
suffices to trigger a sabbat of PCI errors which make the device
completely dysfunctional. The issue has not been reported on a
different platform.
Switching from MMIO accesses to I/O ones as done in Realtek's
own driver fixes (papers over ?) the bug as well but I am not
thrilled to see everyone pay the I/O price for an obscure bug.
This is the minimal change to handle the issue.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Reported-by: Lennert Buytenhek <buytenh@wantstofly.org>
No need to chew CPU cycles as there is no heavy timing requirement
and the delays are always requested from a sleepable context.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
From: Michal Piotrowski <michal.k.k.piotrowski@gmail.com>
Signed-off-by: Michal Piotrowski <michal.k.k.piotrowski@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
- add several PCI ID for the PCI-E adapters ;
- new identification strings ;
- the RTL_GIGA_MAC_VER_ defines have been renamed to closely match the
out-of-tree driver. It makes the comparison less hairy ;
- various magic ;
- the PCI region for the device with PCI ID 0x8136 is guessed.
Explanation: the in-kernel Linux driver is written to allow MM register
accesses and avoid the IO tax. The relevant BAR register was found at
base address 1 for the plain-old PCI 8169. User reported lspci show that
it is found at base address 2 for the new Gigabit PCI-E 816{8/9}.
Typically:
01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd.: Unknown device 8168 (rev 01)
Subsystem: Unknown device 1631:e015
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, cache line size 20
Interrupt: pin A routed to IRQ 16
Region 0: I/O ports at b800 [size=256]
Region 2: Memory at ff7ff000 (64-bit, non-prefetchable) [size=4K]
^^^^^^^^
So far I have not received any lspci report for the 0x8136 and
Realtek's driver do not help: be it under BSD or Linux, their r1000 driver
include a USE_IO_SPACE #define but the bar address is always hardcoded
to 1 in the MM case. :o/
- the 8168 has been reported to require an extra alignment for its receive
buffers. The status of the 8167 and 8136 is not known in this regard.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Rationale:
- its signature is not exactly pretty;
- it has no knowledge of pci_device_id;
- kiss 23 lines good bye.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
The datasheet suggests that the device handles the hardware flow
control almost automagically. User report a different story, so
let's try to twiddle the mii registers.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
For messages prior to register_netdev(), prefer dev_printk() because
that prints out both our driver name and our [PCI | whatever] bus id.
Updates: 8139{cp,too}, b44, bnx2, cassini, {eepro,epic}100, fealnx,
hamachi, ne2k-pci, ns83820, pci-skeleton, r8169.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Having separate fields in sk_buff for TSO/UFO (tso_size/ufo_size) is not
going to scale if we add any more segmentation methods (e.g., DCCP). So
let's merge them.
They were used to tell the protocol of a packet. This function has been
subsumed by the new gso_type field. This is essentially a set of netdev
feature bits (shifted by 16 bits) that are required to process a specific
skb. As such it's easy to tell whether a given device can process a GSO
skb: you just have to and the gso_type field and the netdev's features
field.
I've made gso_type a conjunction. The idea is that you have a base type
(e.g., SKB_GSO_TCPV4) that can be modified further to support new features.
For example, if we add a hardware TSO type that supports ECN, they would
declare NETIF_F_TSO | NETIF_F_TSO_ECN. All TSO packets with CWR set would
have a gso_type of SKB_GSO_TCPV4 | SKB_GSO_TCPV4_ECN while all other TSO
packets would be SKB_GSO_TCPV4. This means that only the CWR packets need
to be emulated in software.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
First of all it is unnecessary to allocate a new skb in skb_pad since
the existing one is not shared. More importantly, our hard_start_xmit
interface does not allow a new skb to be allocated since that breaks
requeueing.
This patch uses pskb_expand_head to expand the existing skb and linearize
it if needed. Actually, someone should sift through every instance of
skb_pad on a non-linear skb as they do not fit the reasons why this was
originally created.
Incidentally, this fixes a minor bug when the skb is cloned (tcpdump,
TCP, etc.). As it is skb_pad will simply write over a cloned skb. Because
of the position of the write it is unlikely to cause problems but still
it's best if we don't do it.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hi,
This patch add new PCI ID for r8169 driver.
RTL8110SBL has this PCI ID.
Please aply.
Yoichi
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
rtl8169_hw_start() requires that the descriptor ring indexes be
set to zero. Let a deferred invocation of rtl8169_reset_task()
handle it. Enabling a few power management bits will not hurt
either.
suspend/resume is issued with irq on: the spinlock do not need
to save the irq flag.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Allow the r8169 driver to set devices to be full-duplex only when
auto-negotiate is disabled.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
The MII registers read/write function blindly busy waits for an
amount of 1000 us (1 ms), then up to 200 ms. These functions are
called from irq disabled context. Depending on the clock management,
it triggers lost ticks events. Since the value is way above the
standard delay required for mii register access, it strangely looks
like a bandaid against posted writes.
Fixes http://bugzilla.kernel.org/show_bug.cgi?id=5947
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
ICC likes to complain about storage class not being first, GCC doesn't
care much (except for cases like "inline static").
have a hard time seeing how it could break anything.
Thanks to Gabriel A. Devenyi for pointing out
http://linuxicc.sourceforge.net/ which is what made me create this patch.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The capabilities of the 8169 can be disabled but it is hardly a reason
to prevent the use the device. The (so far) unusual behavior has been
reported on a MIPS platform by Yoichi Yuasa.
Spotted-by: Yoichi Yuasa <yuasa@hh.iij4u.or.jp>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
I keep on getting "printk: N messages suppressed" messages. We need to test
netif_msg_intr() _before_ running printk_ratelimit(), because the latter
updates state.
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Tone down the r8169 driver
As an alternative, people can use the boot time 'debug' option and/or use
'ethtool -s ethX msglvl xyz'. The different messages are listed at:
http://www.zoreil.com/~romieu/r8169/doc/msglvl.txt
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
vlan_hwaccel_rx should be used when in interrupt context.
Fixes bug http://bugzilla.kernel.org/show_bug.cgi?id=5284
Signed-off-by: Tommy S. Christensen <tommy.christensen@tpack.net>
Cc: Francois Romieu <romieu@fr.zoreil.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Both revisions share the same PCI device ID and vendor ID but revision 2
of the device uses SysKonnect's chipset whereas revision 3 of the device
uses Realtek's 8169 chipset.
Credit goes to Christiaan Lutzer <mythtv.lutzer@gmail.com> for reporting
the issue and giving the actual value for the different revisions.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The Linksys EG1032 uses Realtek's 8169 chipset.
Credit goes to Bob Wilson <bwilson4web@hotmail.com> for the report.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Many drivers use skb->tail unnecessarily.
In these situations, the code roughly looks like:
dev = dev_alloc_skb(...);
[optional] skb_reserve(skb, ...);
... skb->tail ...
But even if the skb_reserve() happens, skb->data equals
skb->tail. So it doesn't make any sense to use anything
other than skb->data in these cases.
Another case was the s2io.c driver directly mucking with
the skb->data and skb->tail pointers. It really just wanted
to do an skb_reserve(), so that's what the code was changed
to do instead.
Another reason I'm making this change as it allows some SKB
cleanups I have planned simpler to merge. In those cleanups,
skb->head, skb->tail, and skb->end pointers are removed, and
replaced with skb->head_room and skb->tail_room integers.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Jeff Garzik <jgarzik@pobox.com>
This is a fixed-up version of the broken "upstream-2.6.13" branch, where
I re-did the manual merge of drivers/net/r8169.c by hand, and made sure
the history is all good.
From: Ralf Baechle <ralf@linux-mips.org>
There are archives of the old list at http://oss.sgi.com/archives/netdev
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
- more consistent prototypes;
- rtl8169_rx_interrupt()
o the error condition should be rare;
o goto removal.
Signed-off-by: Richard Dawe <rich@phekda.gotadsl.co.uk>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
There aren't lots of statistics available, but this is what is available
according to the RealTek documentation.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Also:
- ratelimit the too much work at interrupt message, so if under massive
packet load the console doesn't get flooded;
- removal of a few PFX used in contexts where dev->name is available;
- s/->slot_name/pci_name/;
- printed_version is redundant with the debug option. Remove it and let
the user decide.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
To tell if driver is configured for NAPI or not, put -NAPI on driver
version. Remove the NAPI printk since the complete version information
is displayed once in the pci probe routine or returned via ethtool.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
The USR 997902 is based on the 8169 chipset.
The value has been extracted from the sources of the driver which
comes with the manufacturer's cdrom. Heads-up and test by TommyDrum
<mycooc@yahoo.it>.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
The size of the incoming frame is not correctly checked.
The RxMaxSize register (0xDA) does not work as expected and incoming
frames whose size exceeds the MTU actually end spanning multiple
descriptors. The first Rx descriptor contains the size of the whole
frame (or some garbage in its place). The driver does not expect
something above the space allocated to the current skb and crashes
loudly when it issues a skb_put.
The fix contains two parts:
- disable hardware Rx size filtering: so far it only proved to be able
to trigger some new fancy errors;
- drop multi-descriptors frame: as the driver allocates MTU sized Rx
buffers, it provides an adequate filtering.
As a bonus, wrong descriptors were not returned to the asic after their
processing.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch changes calls to synchronize_kernel(), deprecated in the earlier
"Deprecate synchronize_kernel, GPL replacement" patch to instead call the new
synchronize_rcu() and synchronize_sched() APIs.
Signed-off-by: Paul E. McKenney <paulmck@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This fixes remaining u32s in drivers/ net.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
