Move the definition of the "generic" IRQ in the process.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch adds support for passing platform data to ac97 bus devices
from PXA2xx-AC97 driver..
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
There is one instance of McASP on DA850/OMAP-L138 SoC. This is
connected to TLV320AIC3106 codec for audio playback and capture.
This patch adds audio support on this platform. Some of the
structure prefix names which are common for DA830/OMAP-L137 EVM and
DA850/OMAP-L138 EVM have been renamed to da8xx from da830.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The patch adds a DAI format: Codec bit clock master and frame sync slave,
to the driver.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
On DA830/OMAP-L137 and DA850/OMAP-L138 SoCs, the McASP peripheral has FIFO
support. This FIFO provides additional data buffering. It also provides
tolerance to variation in host/DMA controller response times.
The read and write FIFO sizes are 256 bytes each. If FIFO is enabled,
the DMA events from McASP are sent to the FIFO which in turn sends DMA requests
to the host CPU according to the thresholds programmed.
More details of the FIFO operation can be found at
http://focus.ti.com/general/docs/lit/getliterature.tsp?literatureNumber=
sprufm1&fileType=pdf
This patch adds support for FIFO configuration. The platform data has a
version field which differentiates the McASP on different SoCs.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM8993 analogue control is shared with other devices in the same
product line. Since this is a very substantial proportion of the
driver move the definitions of these controls into a new wm_hubs module
which allows them to be shared between the two.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
A few improvements for IDT 92HD83xxx codec pareser:
- Remove unused / deprecated mixer-amp controls
- Handle d-mics as normal inputs since this codec has no separate
MUXes for analog and digital
- Don't create duplicated controls for capture volumes with Mux
capture volumes
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There has been an ad1836 driver in sound/blackfin based on traditional alsa.
The new driver is based on asoc. The architecture of ad1836 codec driver is
very much like ad1938.
Signed-off-by: Barry Song <21cnbao@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Dynamically control and control only the needed output amplifier
muting/un-muting.
The original code was muting and un-muting the following output
amplifiers: Earpiece PreDrivL/R, CarkitL/R at the same time
regardless which pin is actually in use at the given moment.
Move these as separate PGA so only the needed amplifier will be touched.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
According to the function dapm_dac_check_power() in
sound/soc/soc-dapm.c, dac power can't be on/off stand-alone without any
output widget as sink. And according to dapm_adc_check_power(), adc
power can't be on/off stand-alone without any input widget as source. So
we can't only define some stand-alone SND_SOC_DAPM_DAC/SND_SOC_DAPM_ADC
to hope their power can be managed dynamically.
Signed-off-by: Barry Song <21cnbao@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Enable line-out detection for IDT/STAC codecs only when speaker pins
exist. In some cases, the speaker itself is identified as line-out,
and this confuses the situation. Only the extra line-outs should do
auto-muting.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
the hdsp driver refuses to report any information via the proc
interface, if the io box is not connected. with this patch, the
content of the control and status registers is printed before the
iobox check.
Signed-off-by: Tim Blechmann <tim@klingt.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
With auto config model of alc268 realtek codec, it allows to select any
of possible available digital microphone inputs when only one is
available. For example, when only digital mic in nid 0x12 is available,
on second input source it will allow you to select unavailable digital
mic in nid 0x13. The problem is that selecting unavailable digital mic
creates a source of noise when recording (I'm not sure if this happens
on all machines with alc268 and only one digital mic input, but testing
on a quanta uw1 netbook a lot of noise is introduced in recording from
digital mic 0x12/first input source, when you select the unavailable
digital mic 0x13 for capture source 0x24 in the second input source in
mixer).
Then to avoid noise when recording from digital mic with auto model in
this case, prevent a digital mic input source to be selected if
microphone is not available.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Move static codes to setup from init_hook for each model.
Also, use the common auto-mic selection helper for devices that support
auto-mic selection. They just need to set up ext_mic, int_mic and
auto_mic flag in the setup section.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Store the TDM slot width then if it's set use that rather than the
sample size to calculate BCLK. Leave imposing constraints to the
core (which should do this but doesn't yet) or machine driver.
Also allow 0 TDM slots to be configure (for use when disabling TDM).
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Added setup hook to ALC preset struct to be called at in the parser
but not at each init callback.
This can be used for setting up the static pins, etc, while the
init hook should be used for updating the status again.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Created a white-list to enable MSI since some devices require MSI
explicitly due to BIOS/ACPI problems. Simply using a quirk list.
As the first case, take HP Compaq CQ40.
Reference: Novell bnc#529971
https://bugzilla.novell.com/show_bug.cgi?id=529971
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix soc build errors when I2C is built as a loadable module:
(.text+0x5d26b): undefined reference to `i2c_master_send'
soc-cache.c:(.text+0x5d32d): undefined reference to `i2c_transfer'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Some Realtek codecs don't provide the full connections for certain pins
from each ADC; e.g. ACL662/ALC272 gives only one of two digital-mic pins
for each ADC. Thus, depending on the digital mic pin, the ADC/MUX to be
used has to be chosen properly.
This patch adds the check of the connectivity of pins at auto-mic mode.
If no proper connectivity is found, auto_mic flag is turned off to be
sure.
Also the mux_idx is determined during this check so it won't be checked
in the unsol event any more.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ALC269 and ALC861-VD parsers override the ADC definitions
unconditionally without checking the spec definition. This causes
the problem when any inconsistent ADC is set up in the device quirk
(like ALC272 with digital-mic).
This patch avoids the overriding by adding the proper checks.
Reference: Novell bnc#529467
https://bugzilla.novell.com/show_bug.cgi?id=529467
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix the compile warning due to different integer types used in min():
sound/usb/usbaudio.c: In function 'init_substream_urbs':
sound/usb/usbaudio.c:1087: warning: comparison of distinct pointer types lacks a cast
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added the support for automatic mic selection via plugging for
Realtek codecs (in auto-probing mode). The auto-mic mode is enabled
only when one internal mic and one external mic are present.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If any OSS support is enabled, regardless of built-in or module,
sound_core claims full OSS major number (that is, the old 0-255
region) to trap open attempts and request sound modules using custom
module aliases. This feature is redundant as chrdev already has such
mechanism. This preemptive claiming prevents alternative OSS
implementation.
The custom module aliases are scheduled to be removed and the previous
patch made soundcore emit the standard chrdev aliases too to help
transition.
This patch schedule the feature for removal in a year and makes it
optional so that developers and distros can try new things in the
meantime without rebuilding the kernel. The pre-claiming can be
turned off by using SOUND_OSS_CORE_PRECLAIM and/or kernel parameter
soundcore.preclaim_oss.
As this allows sound minors to be individually grabbed by other users,
this patch updates sound_insert_unit() such that if registering
individual device region fails, it tries the next available slot.
For details on removal plan, please read the entry added by this patch
in feature-removal-schedule.txt .
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Till now missing OSS devices emitted sound-slot/service-* module
alises instead of the standard char-major-* if a missing device number
is opened if soundcore is loaded. The custom module aliases don't
have any inherent benefit than backward compatibility.
sound-slot/service-* module aliases is scheduled to be removed and to
help the transition this patch makes soundcore emit the standard
module alises along with the custom ones.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In the 2.1.6 kernel, the output loop in midi_poll() was changed to
enable interrupts during the outputc() call. Unfortunately, the check
whether the device has accepted the current byte ("ok") was moved behind
the code that removes the byte from the output queue, so one byte would
be lost every time the hardware FIFO is full.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Allow the interval timer to be programmed with its full 96 kHz
precision.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Using more packets in one URB do avoid interrupts does not make sense
when we have a sync pipe whose packets generate interrupts more often.
Therefore, limit the URB size to the synchronization packet interval.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Without the initialization of vmaster NID, the dB information got
confused for ALC269 codec.
Reference: Novell bnc#527361
https://bugzilla.novell.com/show_bug.cgi?id=527361
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Cc: <stable@kernel.org>
The previous auto-mic patch for STAC/IDT codecs causes the Oops on
machines without digital mic pins. This patch fixes the problem.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add support for audio on DA830 EVM- here McASP1 is interfaced to
TLV320AIC3106 codec.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This fixes a build failure for 2.6.31-rc4-rt1 (ARCH=arm, s3c2410_defconfig):
CC [M] sound/soc/s3c24xx/s3c2443-ac97.o
sound/soc/s3c24xx/s3c2443-ac97.c:50: warning: type defaults to 'int' in declaration of 'DECLARE_MUTEX'
sound/soc/s3c24xx/s3c2443-ac97.c:50: warning: parameter names (without types) in function declaration
sound/soc/s3c24xx/s3c2443-ac97.c: In function 's3c2443_ac97_read':
sound/soc/s3c24xx/s3c2443-ac97.c:59: error: 'ac97_mutex' undeclared (first use in this function)
sound/soc/s3c24xx/s3c2443-ac97.c:59: error: (Each undeclared identifier is reported only once
sound/soc/s3c24xx/s3c2443-ac97.c:59: error: for each function it appears in.)
sound/soc/s3c24xx/s3c2443-ac97.c: In function 's3c2443_ac97_write':
sound/soc/s3c24xx/s3c2443-ac97.c:93: error: 'ac97_mutex' undeclared (first use in this function)
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The patch changes the line discipline name registered in include/linux/tty.h
and updates the ams-delta machine driver to use it.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The dma setup code assumes that the buffer size is a multiple
of the period size.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
dai is a parameter to the functions, so use it instead of
looking it up.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Simultaneous audio playback and capture on OMAP1510 can cause that second
stream is stalled if there is enough delay between startup of the audio
streams.
Current implementation of the omap_mcbsp_start is starting both transmitter
and receiver at the same time and it is called only for firstly started
audio stream from the OMAP McBSP based ASoC DAI driver.
Since DMA request lines on OMAP1510 are edge sensitive, the DMA request is
missed if there is no DMA transfer set up at that time when the first word
after McBSP startup is transmitted. The problem hasn't noted before since
later OMAPs are using level sensitive DMA request lines.
Fix the problem by changing API of omap_mcbsp_start and omap_mcbsp_stop by
allowing to start and stop individually McBSP transmitter and receiver
logics. Then call those functions individually for both audio playback
and capture streams. This ensures that DMA transfer is setup before
transmitter or receiver is started.
Thanks to Janusz Krzysztofik <jkrzyszt@tis.icnet.pl> for detailed problem
analysis and Peter Ujfalusi <peter.ujfalusi@nokia.com> for info about DMA
request line behavior differences between the OMAP generations.
Reported-and-tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Extend set_tdm_slot to allow the user to arbitrarily set the frame width
and active TX/RX slots.
Updates magician.c and wm9081.c for the new set_tdm_slot(). wm9081.c
still doesn't handle the slot_width override.
While being there, correct an incorrect use of SlotsPerFrm(7) use in
bitmask on pxa-ssp.c (SSCR0_SlotsPerFrm(x) is (((x) - 1) << 24)) ).
(this series is meant for Mark's for-2.6.32 branch)
Signed-off-by: Daniel Ribeiro <drwyrm@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch is a workaround for the problem of several subsequent control
statements not being applied correctly to the codec controller (modem).
In order to follow the hook switch state change from handset to handsfree
while
in full duplex mode, two consecutive +VLS control commands were sent to the
modem. The first one was M1 (microphone only), the seconds one was M1S1 (both
microphone and speaker). As there was no real modem handshaking procedure
implemented, neither in the codec nor in the machine driver part of the line
discipline, the modem was having the second command missed.
Since a possibility to switch to microphone only mode (and speaker only mode
as well) seams of no value, I have modified the code to issue single M1S1
command only for any of those cases.
Tested on my Amstrad Delta.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds debugging statement that can help in tracing
how the driver is trying to control the codec device.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM8776 is a high performance, stereo audio CODEC with five channel
input selector. The WM8776 is ideal for surround sound processing
applications for home hi-fi, DVD-RW and other audio visual equipment.
This driver implements support for most WM8776 features - currently the
ADC automatic level control/limiter functionality is omitted.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This adds support for i.mx27_visstrim_sm10 board machine driver which
uses an i.mx27 processor plus a wm8974 codec.
It has been tested on a visstrim_sm10 board.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This adds support for DAI platform for the SSI present in MXC platforms.
It currently does not support i.MX3, the only thing necessary to do
this is to export DMA data for i.MX3 interface which I haven't done
because I don't have a i.MX3 based board available.
It has been tested on i.MX27 board.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This adds support for DMA platform valid for i.MX1 and i.MX2 platforms.
This is not valid for i.MX3 since it doesn't share the same DMA
interface than i.MX1 and i.MX2.
It has been tested on i.MX27 board.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Power management for the cs4270 codec is currently implemented as part
of the i2c_driver struct. The disadvantage of doing it this way is that
the callbacks registered in the snd_soc_card struct are called _before_
the codec's callbacks.
That doesn't work, because the snd_soc_card callbacks will most likely
switch down the codec's power domains or pull the reset GPIOs, and
hence make the i2c communication bail out.
Fix this by binding the suspend and resume code to the
snd_soc_codec_device driver model and let the I2C functions only call
the SoC core function for resume and suspend, which do nothing currently
but will do later.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The code in psc_dma_bcom_enqueue_tx() didn't account for the fact that
s->runtime->control->appl_ptr can wrap around to the beginning of the
buffer. This change fixes this problem.
Signed-off-by: John Bonesio <bones@secretlab.ca>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* 'fix/hda' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: hda - Read buffer overflow
ALSA: hda: Correct EAPD for Dell Inspiron 1525
ALSA: hda: warn on spurious response
ALSA: hda: remember last command for each codec
ALSA: hda: read CORBWP inside reg_lock
ALSA: hda: take reg_lock in azx_init_cmd_io/azx_free_cmd_io
ALSA: hda: take cmd_mutex in probe_codec()
ALSA: hda: track CIRB/CORB command/response states for each codec
ALSA: hda - Fix quirk for Toshiba Satellite A135-S4527
When the line-out jack is plugged/unplugged, the driver needs to check
the headphone plug, not only the line-out jack itself. Otherwise the
headphone or the speaker may be wrongly muted/unmuted.
As a result, both STAC_HP_EVENT and STAC_LO_EVENT need to call the
same function, stac92xx_hp_detect().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This converts all the Wolfson drivers using this format (the only devices
that do) except WM8753 to use it.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
As part of this refactoring the type of the CODEC hw_read operation
is changed to match the regular read operation.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
While writes tend to be able to use a fairly bus independant format to
do the writes reads are all bus specific. To allow us to factor out
this code include the bus type as a parameter when setting up the
cache.
Initially just use this to factor out hw_write_t for I2C.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The commit fefd67f31e
ALSA: hda - Add line-out jack detection on IDT/STAC codecs
enabled wrong pins for jack detections. Fixed to the correct ones.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Return STRPIPE instead of EBADF when userspace attempts to rewind
of forward a stream that was suspended in meanwhile, so that it
can be recovered by snd_pcm_recover().
This was causing Pulseaudio to unload the ALSA sink module under a race
condition when it attempted to rewind the stream right after resume from
suspend, before writing to the stream which would cause it to revive the
stream otherwise. Tested to work with Pulseaudio patched to attempt to
snd_pcm_recover() upon receiving an error from snd_pcm_rewind().
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The new IbexPeak HDMI codec has 3 pin nodes and 2 converter nodes.
Here we assume only the first ones will be used.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Check whether index is within bounds before testing the element.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The commit 24918b61b5 statically changes
the model from dell-bios to dell-3stack to solve the sound decreasing
regression (http://lkml.org/lkml/2008/9/12/203), however it leads to another
problem that the 2nd headphone jack doesn't work
(https://bugtrack.alsa-project.org/alsa-bug/view.php?id=3987). So I think
the commit 249**2dc is just a workaround. I would like to give a true solution
here.
The datasheet for STAC9228 says, GPIO2 is the same pin as VOL DOWN, and
the EAPD pin is GPIO0. This is why the sound decreases if we set EAPD as
GPIO2. This patch changes EAPD to GPIO0 to solve the problem.
Signed-off-by: Chengu Wang <wangchengu@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This converts the last CORBWP access outside of reg_lock.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Just for safety. azx_init_cmd_io() and azx_free_cmd_io() may be
called when switching to single command mode.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now that each codec will have its own module, it is possible
for the user to load one codec while another one is running.
So cmd_mutex would be a safe addition to probe_codec().
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Recently we hit a bug in our dev board, whose HDMI codec#3 may emit
redundant/spurious responses, which were then taken as responses to
command for another onboard Realtek codec#2, and mess up both codecs.
Extend the azx_rb.cmds and azx_rb.res to array and track each codec's
commands/responses separately. This helps keep good codec safe from
broken ones.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use model=lenovo instead of model=dallas for Toshiba Satellite A135-S4527
with ALC861-VD codec.
Reference: Novell bnc#526325
https://bugzilla.novell.com/show_bug.cgi?id=526325
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds machine support for Amstrad E3 (Delta) videophone to ASoC.
Created and tested against linux-2.6.31-rc3.
Applies and works with linux-omap-2.6 commit
7c5cb7862d32cb344be7831d466535d5255e35ac as well.
Depends on:
1) latest version of the CX20442 codec driver that exposes v253_ops
structure[1],
2) patch 2/3 form this series: TTY: Add definition of a new line
discipline required by Amstrad E3 (Delta) ASoC driver[2].
CPU DAI parameters best matching the codec DAI has been selected out
empirically for best user experience.
Board specific audio function control (with related DAPM widgets) has been
modeled after empirically discovered codec capabilities.
Unlike other ASoC machine drivers, this one makes use of a codec provided line
discipline that is required for talking to a modem chip that can control the
codec behavoiur. As the line discipline operations must call board specific
bits as well, the machine driver registers its own line discipline ops, not
the codec provided, and then calls those codec provided from inside its own
callbacks.
If some kind of a glue, like a bus over a tty, exsited that could help in
runtime detection of a modem (bus adapter) over a more generic line discipline
(bus driver)[3], the line discipline code could be probably designed in a
more generic way.
In order to work at all, this driver requires a working McBSP1. On OMAP1510
based machines (not sure if other OMAP1 variants as well), where McBSP1 is a
DSP public peripheral, that means the kernel must provide basic DSP support,
ie. omap_dsp_init(), in order to power up the DSP. This used to be included in
linux-omap-2.6 tree up to commit 2512fd29db4eb09e82d182596304c7aaf76d2c5c.
Without that, the driver would not work, ie. not shift in/out any bits over
the CPU DAI[4]. This limitation is not board, but CPU specific, and may apply
to other code that makes use of McBSP1/McBSP3 on affected machines. I provide
an extra patch (4/3) as a temporary solution.
To work correctly in playback mode, this driver requires my prevoiusly
submitted patch that corrects pcm pointer calculation for OMAP1510 based
machines[5] (already included in linux-2.6.31-rc3).
To support codec controls, this driver requires my previously submitted patch
that adds support for modem found on Amstrad Delta[6].
[1] http://mailman.alsa-project.org/pipermail/alsa-devel/2009-July/019780.html
[2] http://www.spinics.net/lists/linux-serial/msg01862.html
[3] http://www.spinics.net/lists/linux-serial/msg01856.html
[4] http://www.spinics.net/lists/linux-omap/msg15114.html
[5] http://mailman.alsa-project.org/pipermail/alsa-devel/2009-June/018950.html
[6] http://www.spinics.net/lists/linux-omap/msg15432.html
Credits to:
Mark Underwood - for his initial, omap-alsa based sound driver for
this machine,
Mark Brown - for his help, patience and excellent subsytem maintainer support.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This corrected patch adds machine independent line discipline code, prevoiusly
exsiting inside my Amstrad Delta ASoC machine dirver, to the Conexant CX20442
codec driver. The code can be used as a standalone line discipline, or as a
set of codec specific functions called from machine's line discipline
callbacks. Anyway, the line discipline itself must be registered by a machine
driver.
Applies on top of the followup to my initial driver version:
http://mailman.alsa-project.org/pipermail/alsa-devel/2009-July/019757.html
Suggested by ASoC manintainer Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The irq can fire as soon as it has been requested, thus all fields accessed
from within the irq handler must be initialized prior to requesting the irq.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This helps CODECs with sparse register maps work better with the
register cache display interface.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Check that the result of kzalloc is not NULL before a dereference.
The semantic match that finds this problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
expression *x;
identifier f;
constant char *C;
@@
x = \(kmalloc\|kcalloc\|kzalloc\)(...);
... when != x == NULL
when != x != NULL
when != (x || ...)
(
kfree(x)
|
f(...,C,...,x,...)
|
*f(...,x,...)
|
*x->f
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The name buf with size 16 is too short for some codec names, e.g.
truncated like "ALC861-VD Analo". Now the size is doubled.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add the automatic mute of speakers via line-out jack plugging on
STAC/IDT codecs. The feature is enabled when the HP detect is present.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The patch below, to be applied on the latest sound-unstable-2.6.git,
enables headphones output on my MacBookPro 5,5, together with the
automuting feature.
Here is the exact soundcard id:
Vendor Id: 0x10134206
Subsystem Id: 0x106b4d00
Revision Id: 0x100301
Signed-off-by: Takashi Iwai <tiwai@suse.de>
STAC/IDT codecs provide both "Input Source" and "Digital Input Source"
controls to choose the analog input source and the digital input source.
But this is far user-unfriendly.
This patch merges the input source selections into one "Input Source"
control. To have separate digital and analog input source controls,
you can pass "separate_dmux = 1 " hint string.
At the same time, this patch gets rid of analog mixer stuff that was
already disabled in previous patches.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It auto mutes all 8-channel outputs at rear panel when
the front panel headphone is connected.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This 2-channel mode is useful in that it will broadcast
a 2-channel audio stream to all front/side/... ports.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
1. fix "line over 80 characters" checkpatch warnings
2. ‘DMA_nnBIT_MASK’ is deprecated, use DMA_BIT_MASK instead
3. fix typos
Signed-off-by: Barry Song <21cnbao@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
With the s3c platform has implementing gpiolib support the s3c_gpio api has been
deprecated.
This patch gets rid of all s3c_gpio calls and replaces them by using gpiolib.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The analog mix is disabled now as default (unless "analog_mixer" hint
is given), so it shoudn't appear in the digital input source as well.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added the missing initialization of DMUX connection (to analog input)
for auto-mic mode with STAC/IDT codecs.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We don't need any more static connection to the port F (which is often
used for docking stations) since its connection is done dynamically via
DAC assignment now.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
mpu_synth_info[m].name is a char[30], and the minimum length of the data
written by sprintf is 31 bytes including terminating null.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
DSPVersion is declared as char[3], but the sprintf writes at least 4 bytes
including terminating null.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
e->sad[] is declared with size ELD_MAX_SAD=16, but the guard
allows range 0-31.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Support the automatic mic-switching with some devices with IDT/STAC
codecs. The condition is that the device has only two inputs, one
for an external mic and one for an internal mic.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since only one event can be associated to a (pin) widget, it's safer
to avoid the multiple mapping. This patch fixes the behavior of the
STAC/IDT codec driver.
Now stac_get_event() doesn't take the type argument but simply returns
the first hit element. Then enable_pin_detect() checks the validity
of the type, and returns non-zero only if a valid entry. The caller
can call stac_issue_unsol_event() after checking the return value.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The I2S DAI driver for blackfin SPORT, but works in TDM mode.
I2S is not a special case of TDM with only left and right two slots for
SPORT interface. I2S coordinates with TDM in SPORT, but not a part of
TDM. TDM require different hardware configuration with I2S, not only
different slot number. One is "Stereo Serial Operation" mode of SPORT,
the other one is "Multichannel Operation" mode. They are incompatible
at the same time.
Hardware and DMA description and data transfer flow are much different
for I2S and TDM. Merging them as a whole will be very ugly and difficult
to maintain.
So we don't define a new DAI type, but give two DAI instances for standard
I2S and TDM, both in I2S-family DAI type. The TDM instance still uses the
I2S-family DAI type.
Signed-off-by: Barry Song <21cnbao@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The patch fixes some checkpatch identified issues and adds a comment about
line discipline interaction to my driver code, as requested by Mark on my
inital submission (thank you Mark for applying my imperfect patch anyway).
It also fixes MODULE_ALIAS mismatch as used in my machine driver.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The analog mixer unit on IDT 92HD71Bxx codecs is almost useless
since we use only the direct connections from DAC to pin.
Remove the controls to avoid unneeded confusion as default now.
This can be still back via "analog_mixer = 1" hint.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Instead of static snd_kcontrol_new arrays, create "Capture Volume"
and "Capture Switch" controls dynamically based on the mixer attr
values (made via HDA_COMPOSE_AMP_VAL()).
This reduces the code size and gives more flexibility to change
the number of controls later.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The current driver creates always the digital input source mixer
elements for IDT 92HD71x codecs no matter whether digital mics are
present. This patch adds the proper check to avoid the creation of
these controls if unnecessary.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The sentense "Unknown model for xxx, ..." makes people too nervous
and drives them to a direction to a wrong "fix" by giving any
mismatching model option.
Let's rephrase the messages to be more nice and easy (at least that
won't make people suspect conspiracies).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Volume-knob widgets may have connections even if they have no CONN_LIST
cap bit. Allow the query exceptionally in snd_hda_get_connections().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
* fix/hda:
ALSA: hda - Fix mute control with some ALC262 models
ALSA: hda - Restore GPIO1 properly at resume with AD1984A
ALSA: hda - Use snprintf() to be safer
The master mute switch is wrongly implemented as checking the pointer
instead of its value, thus it can be never muted. This patch fixes
the issue.
Reference: Novell bnc#404873
https://bugzilla.novell.com/show_bug.cgi?id=404873
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Cc: <stable@kernel.org>
This patch removes the old method of jack detection from palm27x-asoc
driver and adds jack detection api. It also removes some other (now)
useless stuff from the driver and corrects pin configuration for the
codec.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The patch adds a few small enhancements to the ASoC jack handling, as
suggested by Mark in his comments to my Amstrad Delta driver, and a few fixes
for related bugs found while learning Mark's code and testing results.
Enhancements:
1. Update status of an ASoC jack while associating it with new gpios.
2. Really update DAPM pins while associating them with an ASoC jack.
3. Export ASoC jack gpios over gpiolib sysfs for diagnostic purposes.
Fixes:
1. Apply mask on jack status report before using it, just for case.
2. While updating jack associated DAPM pins, use full resulting jack status,
not the status report passed as an argument.
Created and tested on linux-2.6.31-rc3
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This adds support for Native Instrument's freshly announced Audio2DJ
sound device hardware. Version number bumped to 1.3.19.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The fix 79452f0a28 introduced another
bug due to the missing offset for the overlapped hwptr.
When the hwptr goes back to zero, the delta value has to be corrected
with the buffer size. Otherwise this causes looping sounds.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch allows passing platform_data to devices attached to AC97 bus
(like touchscreens, battery measurement chips ...).
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The MAX9877 needs an address of start register when we write values to
registers through i2c_master_send(), but the code for this was missed in
max9877_write_regs().
If the value of control is 0 in the max9877_set_out_mode(), the value is
not increased to 1, but actually the value to write to the register
should be 1.
And the register bits for out_mode and osc_mode should be cleared before
writing.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds support for Conexant CX20442-11 voice modem codec, suitable
for use by the ASoC board driver for Amstrad E3 (Delta) videophone. Related
sound card driver will follow.
This codec is an optional part of the Conexant SmartV three chip modem design.
As such, documentation for its proprietary digital audio interface is not
available. However, on Amstrad Delta board, thanks to Mark Underwood who
created an initial, omap-alsa based sound driver a few years ago[1], the codec
has been discovered to be accessible not only from the modem side, but also
over the OMAP McBSP based CPU DAI. Thus, the driver can be used by any sound
card that can access the codec DAI directly. The DAI configuration parameters
(sample rate and format, number of channels) has been selected out empirically
for best user experience.
The codec analogue interface consists of two pairs of analogue I/O pins:
speakerphone interface or telephone handset/headset interface. Furthermore, it
seams to provide two operation modes for speakerphone I/O: standard and
advanced, with automatic gain control and echo cancelation. Even if the codec
control interface is unknown and not available, all those interfaces and modes
can be selected over the modem chip using V.253 commands. The driver is able
to issue necessary commands over a suitable hw_write function if provided by a
sound card driver. Otherwise, the codec can be controlled over the modem from
userspace while inactive.
Even if nothig is known about the codec internal power management
capabilities, DAPM widgets has been used to model the codec audio map.
Automatically performed powering up/down of those virtual widgets results in
corresponding V.253 commands being issued.
Some driver features/oddities may be board specific, but I have no way to
verify that with any board other than Amstrad Delta.
[1] http://www.earth.li/pipermail/e3-hacking/2006-April/000481.html
Created and tested against linux-2.6.31-rc3.
Applies and works with linux-omap-2.6 commit
7c5cb7862d32cb344be7831d466535d5255e35ac as well.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Here are the new sound enabling patches for IbexPeak.
Summary of tested features:
- playback
- Front Headphone: OK
- 8 channel audio: Front/Rear/CLFE/Side all OK
- recording
- Front Mic/Rear Mic: both OK
(front/rear/line mics are selectable in the "Input source" alsamixer control)
- Line In: not working
(in 6ch mode, its amp/mute, direction and route all looks fine,
so I'm a little puzzled)
(hopefully no one will care this feature)
- digital SPDIF input/output: not tested (no equipment)
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added the logging functionality to xrun_debug to record the hwptr
updates via snd_pcm_update_hw_ptr() and snd_pcm_update_hwptr_interrupt(),
corresponding to 16 and 8, respectively.
For example,
# echo 9 > /proc/asound/card0/pcm0p/xrun_debug
will record the position and other parameters at each period interrupt
together with the normal XRUN debugging.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
PLL was not being enabled when it was not bypassed. This patch
enables the PLL when it is used. Additionally, it disables the PLL
when it is bypassed.
Without this patch, the audio on TI DM646x EVM and DM355 EVM
does not work properly. The bit clocks and the frame sync signals
from the codec are not correct and hence the playback/record are faster
than usual for most sample rates. The reason for this was that the PLL
was not enabled when it was not bypassed.
Tested on DM6467 EVM, playback tested on DM355 EVM.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The commit 099db17e66 introduced a
regression at suspend/resume where the GPIO1 bit isn't properly
restored, thus the speaker output gets muted initially after resume.
The fix is simple, use the cached write for storing GPIO data.
Reference: Novell bnc#522764
https://bugzilla.novell.com/show_bug.cgi?id=522764
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix a few uninitialized error checks that were introduced recently
mistakenlly during the clean-up:
sound/pci/ctxfi/ctamixer.c: In function ‘get_amixer_rsc’:
sound/pci/ctxfi/ctamixer.c:261: warning: ‘err’ may be used uninitialized in this function
sound/pci/ctxfi/ctamixer.c: In function ‘get_sum_rsc’:
sound/pci/ctxfi/ctamixer.c:415: warning: ‘err’ may be used uninitialized in this function
sound/pci/ctxfi/ctsrc.c: In function ‘get_srcimp_rsc’:
sound/pci/ctxfi/ctsrc.c:742: warning: ‘err’ may be used uninitialized in this function
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds a check to snd_hda_get_connections() routine for
presence of AC_WCAP_CONN_LIST. Also, make sure that negative error
codes from noted route are handled on all places as errors.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
- E3500 report cval->max more than it actually can handel, so if you
set 95% capture level it will be silently muted.
- Betwen cval->min and cval-max(real) is 2940 control units,
but real are only 7 with cval->res = 384.
- Alsa can't handel less than 10 controls, so make it more
and set cval->res = 192.
Signed-off-by: Alexey Fisher <bug-track@fisher-privat.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Previous patch used widget type, but the presence flag of the connection
list is in the widget capabilities.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reading node connections for an unknown widget can confuse HDA codec bus.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix the logic of ALC861 auto-mode parser for the outputs.
Instead of assuming the fixed DAC list, parse the conection and assign
the DAC dynamically.
Also, unmute the unused output connections to avoid noises on inputs.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
VMware tends to report PCM positions and period updates at utterly
wrong timing. This screws up the recent PCM core code that tries
to correct the position based on the irq timing.
Now, when a backward irq position is detected, skip the update
instead of rebasing. (This is almost the old behavior before
2.6.30.)
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add some tricks to reduce the click noise at powering down to D3
in the power saving mode on STAC/IDT codecs.
The key seems to be to reset PINs before the power-down, and some
delay before entering D3. The needed delay is significantly long,
but I don't know why.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The callback function to control register was used by whole controls in
MAX9877 driver, but this causes using many if statement for double
register control or invert.
So, the callback function for double register control is separate
differently, and the code for invert is added in the callback function.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This corrects a bug with ADC Inversion Switch in wm8974 codec.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reset was failing with the original udelay(50) between the code in
psc_ac97_cold_reset() and the call to psc_ac97_warm_reset(). Through testing
it was found that a delay of 1ms was necessary for the cold_reset code to
consistently complete successfully.
Signed-off-by: John Bonesio <bones@secretlab.ca>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* fix/misc:
ALSA: ca0106 - Fix the max capture buffer size
ALSA: OSS sequencer should be initialized after snd_seq_system_client_init
ALSA: sound/isa: convert nested spin_lock_irqsave to spin_lock
* fix/hda:
ALSA: hda - Fix pin-setup for Sony VAIO with STAC9872 codecs
ALSA: hda - Add quirk for Gateway T6834c laptop
ALSA: hda_codec: Check for invalid zero connections
On Soundblaster X-FI Titanium with emu20k2 the SIDE and SURROUND
channels were swapped and wrong.
I double checked it with connector colors and creative soundblaster
windows drivers.
So I swapped them to the true order.
Now "speaker-test -c6" and "speaker-test -c8" are working fine.
Signed-off-by: Frank Roth <frashman@freenet.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The capture buffer size with 64kB seems broken with CA0106.
At least, either the update timing or the DMA position is wrong,
and this screws up pulseaudio badly.
This patch restricts the max buffer size less than that to make life
a bit easier.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Cc: <stable@kernel.org>
The recent rewrite of the codec parser for STAC9872 caused a regression
for some Sony VAIO models that don't give proper pin default configs
by BIOS. Even using model=vaio doesn't work because the pin definitions
are set after the pin overrides.
This patch fixes the pin definitions in patch_stac9872() to be put
in the right place before the pin overrides. Also the patch adds the
new quirk entry for VAIO F/S to have the correct pin default configs.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Cc: <stable@kernel.org>
Added the native timer support for emu20k2, which gives much more
accurate update timing than the system timer.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Gateway T6834c laptops need EAPD always on while the default behavior
for the STAC9205 reference board is to turn it off upon every HP plug.
By using the special "eapd" model, which is first introduced for Gateway
T1616 laptops for this same reason, this peculiarity can be properly
handled.
Signed-off-by: Hao Song <baritono.tux@gmail.com>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If spin_lock_irqsave is called twice in a row with the same second
argument, the interrupt state at the point of the second call overwrites
the value saved by the first call. Indeed, the second call does not need
to save the interrupt state, so it is changed to a simple spin_lock.
The semantic match that finds this problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
expression lock1,lock2;
expression flags;
@@
*spin_lock_irqsave(lock1,flags)
... when != flags
*spin_lock_irqsave(lock2,flags)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
To prevent "Too many connections" message and the error path for some HDMI
codecs (which makes onboard audio unusable), check for invalid zero
connections for CONNECT_LIST verb.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
GCC 4.4.0 doesn't appear to be able to spot that we don't apply any FLL
configuration if the output frequency is zero.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
- Parse the mono output pin 0x16 correctly even as the primary output
- Create "Speaker" volume control if the primary output is a speaker
- Fix the wrong direction of (optional) "Mono" switch
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The newly added sanity-check for a codec verb can be better written
with logical ORs. Also, the parameter can be more than 8bit.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Board sdp3430 has hardware support for EXTMUTE using TWL4030 GPIO6
line, controlled by register INTBR_PMBR1. Machine driver takes care
of enabling gpio line through i2c and codec driver manipulates the
line during headset ramp up/down sequence.
Signed-off-by: Jorge Eduardo Candelaria <x0107209@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
A recent bug involves passing auto detected >0x7f NID to codec command,
creating an invalid codec addr field, and finally lead to cmd timeout
and fall back into single command mode. Jaroslav fixed that bug in
alc880_parse_auto_config().
It would be safer to further check the bounds of all cmd fields.
Cc: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add support for new AMD HD audio devices. Use generic driver to detect HD audio
devices with Vendor ID AMD.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This adds support for the Conexant CX20582 codec, based on code from
http://www.linuxant.com/alsa-driver/alsa-driver-linuxant-1.0.19ppch12-1.noarch.rpm.zip
This is the codec to be shipped in the OLPC XO-1.5, so this patch also
includes an XO-specific profile. Resultant configuration:
http://dev.laptop.org/~dsd/20090713/codec0.txthttp://dev.laptop.org/~dsd/20090713/codec0.svg
As the Linuxant code is structured differently to the other codecs,
I was unable to cleanly reimplement everything in the generic and Dell
profiles as more info is needed (e.g. codec graphs). I simplified those
profiles so that hopefully it will not break anyone's audio. If it does,
it may be worth returning -ENODEV from patch_cx5066 on non-OLPC systems,
and then fixing snd_hda_codec_configure() to fall back on the generic
parser, at least until support for other systems is figured out.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
clock name strings are no longer passed on platform_data. Instead,
we rely entirely on struct device and clkdev to find the right clock.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The MAX9877 combines a high-efficiency Class D audio power amplifier
with a stereo Class AB capacitor-less DirectDrive headphone amplifier.
The max9877_add_controls() is called to register the MAX9877 specific
controls on machine specific init() of the machine driver.
The datasheet for the MAX9877 can find at the following url:
http://datasheets.maxim-ic.com/en/ds/MAX9877.pdf
[Slight edit to sort the ALL_CODECS entries -- broonie.]
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We need to check returning error for pci_register_driver(&joystick_driver)
On failure, we should unregister formerly registered audio drivers
This also fixed the compiler warning :
CC [M] sound/pci/riptide/riptide.o
sound/pci/riptide/riptide.c: In function ‘alsa_card_riptide_init’:
sound/pci/riptide/riptide.c:2200: warning: ignoring return value of ‘__pci_register_driver’, declared with attribute warn_unused_result
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Due to the flexibility of the WM9081 FLL this should never happen
in a real system.
Reported-by: Jaswinder Singh Rajput <jaswinder@kernel.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
- fix my previous codec activity breakage (_non-warned_ variable assignment
issue)
- convert suspend/resume to 32bit I/O access (I/O is painful; to improve
suspend/resume performance)
- change DEBUG_PLAY_REC to DEBUG_CODEC for consistency
- printk cleanup
- some logging improvements
- minor cleanup/improvements
The variable assignment issue above was a conditional assignment to the
call_function variable (this ended with the non-preinitialized variable
not getting assigned in some cases, thus a dangling stack value, yet gcc 4.3.3
unbelievably did _NOT_ warn about it in this case!!),
needed to change this into _always_ assigning the check result.
Practical result of this bug was that when shutting down
_either_ playback or capture, _both_ streams dropped dead :P
Tested, working (plus resume) and checkpatch.pl:ed on 2.6.30-rc5,
applies cleanly to 2.6.30 proper with my previous (committed)
patches applied.
Signed-off-by: Andreas Mohr <andi@lisas.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Sending an Active Sensing message when closing a port can interfere with
the following data if the port is reopened and a note-on is sent before
the device's timeout has elapsed. Therefore, it is better to disable
this setting by default.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Instead of using magic numbers for the controlles sent when resetting
a port, use the symbols from asoundef.h.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Sending a MIDI reset message when closing a port is wrong because we
only want to shut the device up, not to reset all settings.
Furthermore, many devices ignore this message.
Fortunately, the RawMIDI layer already shuts the device up, so we can
ignore this matter here.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When draining, instead of waiting for fifty milliseconds, just wait for
the currently active URBs to complete. This cuts the usual waiting time
down to one USB frame, or zero in the common case when there is no URB.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some newer USB MIDI interfaces use rather small packet sizes, so to get
enough bandwidth, we have to be able to send multiple packets in one USB
frame, so we have to use multiple URBs.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some newer USB MIDI interfaces use rather small packet sizes, so to get
enough bandwidth, we have to be able to receive multiple packets in one
USB frame, so we have to use multiple URBs.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It turns out that the main cause of output buffer overruns is not slow
drivers but applications that generate too many messages. Therefore, it
makes more sense to make that error message always visible, and to
rate-limit it.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add support for the Asus Xonar U1. This device is mostly class compliant, but
the digital output requires a vendor-specific request.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Blue Microphones USB devices have an alternate setting that sends two
channels of data to the computer. Unfortunately, the descriptors of
that altsetting have a wrong channel setting, which means that any
recorded data from such a device has twice the sample rate from what
would be expected.
This patch adds a workaround to ignore that altsetting. Since these
devices have only one actual channel, no data is lost.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We need to use the best value we picked, not the last value we
looked at.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
There is no need to manually start playback/capture ourselves as the PCM
driver will handle things for us.
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
There is no need to manually start playback/capture ourselves as the PCM
driver will handle things for us.
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Without MODULE_LICENCE("GPL"), when built as a module it will fail
to load because it uses other GPL symbols from kernel.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In SOC DAPM layer of SOUND subsystem, when add signal route (in the
function snd_soc_dapm_add_route() ), the original code has wrong logic
when dapm layer check each widget whether an external one.
Signed-off-by: Rongrong Cao <rrcao@ambarella.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is the last in-kernel direct usage of driver_data, replace it with
the proper dev_get/set_drvdata() calls.
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Jaroslav Kysela <perex@perex.cz>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The codec read errors in snd_hda_get_connections() are ignored so far,
and it causes a problem like the bug in the commit
9d30937acc
ALSA: hda_intel: more strict alc880_parse_auto_config dig_nid checking
Better to check errors in the function and returns a proper error code
rather than passing bogus NID values.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On some IbexPeak systems with ALC889A errors like "azx_get_response
timeout, switching to polling mode: last cmd=0xaf9f000b" are produced,
because non-existent codec #10 is wrongly accessed.
The problem is that snd_hda_get_connections() returns out-of-range result
for NID 0x1c (something like 0xf8f9 or 0xffff).
This patch adds a check to alc880_parse_auto_config() to avoid using
of this out-of-range NIDs. A better fix maybe to improve
snd_hda_get_connections() routine to check for valid NID ranges if
NIDs are expected as result.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix the merge error at the commit 305355aad8,
an addition of the missing alc880_gpio3_init_verbs to ALC882_TARGA model.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
* fix/asoc:
ASoC: Fix wm8753 register cache size and initialization
ASoC: add locking to mpc5200-psc-ac97 driver
ASoC: Fix mpc5200-psc-ac97 to ensure the data ready bit is cleared
ASoC: Fix register cache initialisation for WM8753
Simplify ALC882_TARGA and return gpio3 to ALC883_TARGA_DIG and
ALC883_TARGA_2ch_DIG, which I accidentally removed in commit id
64a8be7435
Signed-off-by: David Heidelberger <d.okias@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The WM8731 driver has been updated to allow registration via normal
device model methods rather than from within the ASoC driver probe
so update the AT91SAM9G20-EK to make use of this.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Check for rtd->params->drcmr != NULL before accessing it.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In the beep tone calculation for IDT/STAC codecs, lower numbers correspond
to higher frequencies and vice versa. The current code has this backwards,
resulting in beep frequencies which are way too high (and sound bad on
tinny laptop speakers, resulting in complaints).
[Also added hz <= 0 check by tiwai]
Signed-off-by: Paul Vojta <vojta@math.berkeley.edu>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Provide an interval after the end of DAPM sequencing so that we
can distinguish between a pop in the final step of the sequence
and a pop generated from some other source outside DAPM.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The system clock is currently fixed by the driver and this avoids
the need for us to handle errors with enabling and disabling MCLK
(which was incorrect previously so this fixes bugs in error
handling).
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Commit 5fd29d6ccb ("printk: clean up
handling of log-levels and newlines") changed printk semantics. printk
lines with multiple KERN_<level> prefixes are no longer emitted as
before the patch.
<level> is now included in the output on each additional use.
Remove all uses of multiple KERN_<level>s in formats.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As shipped the board does not have inputs but it is relatively
straightforward to modify the board to hook them up so support
is provided in the driver. When these modifications have not
been made enabling the microphone stage can cause problems.
Add an ifdef to disable this by default. Don't put it into
Kconfig since users will have to get their soldering irons
out to change things.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This simplifies the driver by removing the need to manually
configure dividers within the CPU and improve audio performance
by ensuring that the optimal phase relationships between the
clocks in the system are maintained.
Note that currently this means that for playback to work the
Output Mixer HiFi switch must be enabled since otherwise CODEC
will not generate the DAC clock.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
While the hardware is capable of some limited asynmmetric modes the
driver does not currently support those modes so tell applications
that only symmetric rates are available.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM8993 is a highly integrated ultra-low power hi-fi CODEC designed
for portable devices such as multimedia phones.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Update the dma link with correct data as soon as
the master channel has copied it. Otherwise, the
1st period will play twice.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
There is a regression, introduced in aa202455ee
(in alsa-kernel) which I noticed when trying to use the headphone socket on
my EeeCPC 901: the output was *very* quiet, practically silent.
This patch corrects the control types to that which was obviously intended in
the referenced commit.
Signed-off-by: Darren Salt <linux@youmustbejoking.demon.co.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Using SG-buffers with dma_alloc_coherent() is often very inefficient
on non-coherent architectures because a tracking record could be
allocated in addition for each dma_alloc_coherent() call.
Instead, simply disable SG-buffers but just allocate normal continuous
buffers on non-supported (currently all but x86) architectures.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HDA driver disabled HD audio 64bit address support for all AMD
SB600/SB700/SB800 platforms with commit
09240cf429 due to one SB600 issue
reported by community, but we do not see the similar issue on
SB700/SB800 platforms.
This patch is to refine the workaround for SB600 only.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Check the widget type and don't take invalid widgets while parsing
the capture source in patch_via.c.
Also, fixed some compile warnings introduced in the previous commit.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Adding MPU-401 support to cmi8330 driver could cause a regression (non-working
sound) on a system where there is no free IRQ for the MPU-401 device (which
is not very uncommon as this card requires two separate IRQs plus a third one
for MPU-401).
When MPU-401 PnP configuration fails (mostly because of unavailable IRQ), just
ignore MPU-401 and continue without it.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The fixed widget NIDs in patch_via.c seem wrong for some codecs,
and it resulted in the invalid capture source selection.
This patch adds the code to parse the topology instead of using
fixed numbers in order to get the right MUX widget id corresponding
to the ADCs.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If the output pin is used and EAPD capability is present, turn on
the EAPD bit. This fixes the silent output problem on ASUS laptops
with VT1708S codec.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
My CMI8329 had OPL3 port specified in SB16 resources. But now I found out that
it was my modification of the card's PnP EEPROM a couple of years ago (can be
done using C9SETROM.EXE utility). I did it because the OPL3 port was
completely missing from PnP data. It seems to be hardwired to 0x388 on
CMI8329.
Find OPL3 port automatically by searching in WSS and SB16 resources. If not
found, assume that it's hardwired to 0x388.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The parser wasn't called in the proper order.
Split now the parser to be called in patch_cirrus(), and the rest
are just for building PCMs and controls.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
- fully separate codec I/O port handling, enabling the use of a single
function each for all codecs (playback, capture, I2S out)
- add a new separate pcm for I2S out port (UNTESTED, no I2S DAC
available yet)
- switch gameport to low frequency while idle, to try to reduce noise/power
- improve snd_azf3328_codec_setdmaa() calculation
- minor variable type cleanup (u16, bool etc.)
- add some doc updates (help those lost Windows users, debug help, ...)
Note that due to the large cleanup aspect of the codec I/O change,
I was able to fit everything including all improvements into the
same binary size!! (a measly 10 bytes more or so)
This should now be the almost last patch to this driver
(minus some possible kernel clocksource patch and x86_64 fixes or so).
I just felt like taking a break from the usual stuff and wanted to
get this driver's structure finished, and it's rather clean now...
Tested, working and checkpatch.pl:ed on 2.6.30-rc5,
applies cleanly to 2.6.30 proper.
Signed-off-by: Andreas Mohr <andi@lisas.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This driver is about as far from being experimental as it can ever get
for an undocumented card, thus create this patch (interestingly it was the only
EXPERIMENTAL remaining in the entire Kconfig file).
Signed-off-by: Andreas Mohr <andi@lisas.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Note the slightly tricky cache usage in the volume update function due
to the requirement for a separate write for the VU bit.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The TLV320AIC3x driver is currently the only user of the CODEC hw_read
operation and is jumping through some hoops in order to do so. In order
to support future refactoring to make the hw_read operation more usable
unwrap the usage in this driver to avoid its use.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Nothing uses it and the existing hw_read operation needs to be
refectored so it's easier to remove it rather than work with it.
Support can be re-added if the code requires volatile registers.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
A lot of CODECs share the same register data formats and therefore
replicate the code to manage access to and caching of the register
map. In order to reduce code duplication centralised versions of
this code will be introduced with drivers able to configure the use
of the common code by calling the new snd_soc_codec_set_cache_io()
API call during startup.
As an initial user the 7 bit address/9 bit data format used by many
Wolfson devices is supported for write only CODECs and the drivers
with straightforward register cache implementations are converted to
use it.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add a volatile_register() operation to the CODEC structure providing a
standard operation to query if a register is volatile. This will be used
to factor out the register cache I/O operations for the CODECs.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If the codec is master then prepare should call
mcbsp_start, not trigger.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Code previously just "ors" in this field without clearing
first. Fix, by never reading this register.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Only start sample generator if needed, and more
cleanup on davinci_mcbsp_start.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Move variable declaration closer to use.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add davinci_mcbsp_dev as argument to davinci_mcbsp_start
and davinci_mcbsp_stop.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add toggle_clock function to complete i2s reset earlier.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
No functional changes. Rename variable w to something
more meaningful. Remove code obfuscating macro MOD_REG_BIT.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add basic support for CMI8329 cards. Makes PCM and OPL3 work.
Does not break CMI8330 (tested).
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
* fix/hda:
ALSA: hda - Add sanity check in PCM open callback
ALSA: hda - Call snd_pcm_lib_hw_rates() again after codec open callback
ALSA: hda - Avoid invalid formats and rates with shared SPDIF
ALSA: hda - Improve ASUS eeePC 1000 mixer
ALSA: hda - Add GPIO1 control at muting with HP laptops
When FLOAT PCM format is available but together with other linear
PCM formats, don't override maxbps value. For FLOAT format, it's always
32, thus it can be better checked in snd_hda_calc_stream_format().
Otherwise the maxbps 32 might be used wrongly even if the linear PCM
doesn't support it.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add some sanity checks of struct snd_pcm_hardware fields in the PCM
open callback of hda driver. This makes a bit easier to debug any PCM
setup errors in the codec side.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The PCM rates bit field may have been changed by the codec open callback.
In that case, we need to reset rate_min and rate_max. So, simply call
snd_pcm_lib_hw_rates() again after the codec open callback.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Check whether formats and rates don't result in zero due to the
restriction of SPDIF sharing. If any of them can be zero, disable
the SPDIF sharing mode instead. Otherwise it will lead to a PCM
configuration error.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Register cache space was not being allocated for the final register,
causing bugs when it was used. Allocate space for it.
Also ensure that the final register is displayed in sysfs.
[Commit message rewritten to document actual issue. -- broonie]
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The mixer elements created for ASUS eeePC 1000 with ALC269 aren't
standard but strange words like "LineOut". Rename the element names
to follow the standard one like "Headphone" and "Speaker".
Also, split the volumes to each so that the virtual master can control
them.
The alc269_fujitsu_mixer is removed because it's now identical with
the new eeepc mixer.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HP laptops with AD1984A codecs (at least mobile models) need to set
GPIO1 appropriately to indicate the mute state. The BIOS checks this
bit to judge whether the mute on or off is sent via F8 key.
Without changing this bit, the BIOS can be confused and may toggle
the mute wrongly.
Reference: Novell bnc#515266
https://bugzilla.novell.com/show_bug.cgi?id=515266
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add "set_tristate" callbacks for HiFi and Voice DAIs.
Machine drivers can enable and disable tristate for each
DAI with "snd_soc_dai_set_tristate" function.
Signed-off-by: Misael Lopez Cruz <x0052729@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add support for EXTMUTE in Zoom2 machine driver. This is necessary
to further reduce pop noise problem. Signal EXTMUTE is connected to
signal GPIO 153 in Zoom2 board.
In addition, change ramp delay value to 3 (218/161/109 ms). With
previous ramp delay value, pop noise was louder. With a longer value
the beep tone can be observed.
Signed-off-by: Jorge Eduardo Candelaria <x0107209@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
AC97 bus register read/write hooks need to provide locking, but the
mpc5200-psc-ac97 driver does not. This patch adds a mutex around
the register access routines.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Jon Smirl <jonsmirl@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When doing register reads, it is possible for there to be a stale
data ready bit set which will cause subsequent reads to return
prematurely with incorrect data. This patch fixes the issues by
ensuring stale data is cleared before starting another transaction.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Jon Smirl <jonsmirl@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The wrong register cache variable was being used to provide the size for
the memcpy(), resulting in a copy of only a void * of data.
Reported-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
Instead of expanding alc882_init_verbs to two elements via a macro,
manually expand to each entry. This makes clear that some have already
the full slot for init_verbs array (currently 5).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
After merting patch_alc882() and patch_alc883(), the initialization of
mixer amp 0x0b was missing in alc882_base_init_verbs[].
This is usually no critical problem, but it can disable the power-saving
as the default state, so better to put to mute these channels.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
According to TRM, an external FET controlled by a 1.8V output signal
can be used to reduce the pop-noise heard when the audio amplifier is
switched on. It is suggested that GPIO6 of TWL4030 be used, but any
other gpio can be used instead. This is indicated in machine driver
with the following twl4030_setup_data members:
-hs_extmute. Set to 1 if board has support for EXTMUTE.
-set_hs_extmute. Set to a callback funcion to control an external gpio
line. Set to NULL if MUTE[GPIO6] pin is used.
Codec driver takes care of enabling and disabling this output during
the headset pop attenuation sequence.
Also add a delay to let VMID settle in ramp up sequence.
Signed-off-by: Jorge Eduardo Candelaria <x0107209@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The sound device instance needs to be a child of the USB interface, not
the USB device. Newer udev versions pay attention to that.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Reported-by: Lennart Poettering <lennart@poettering.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When resuming, we better take the DACs out of the reset state before
trying to use them.
Reference: kernel bug #13599http://bugzilla.kernel.org/show_bug.cgi?id=13599
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The WM8523 is a high performance stereo DAC with integral charge
pump providing 2Vrms line driver outputs using a single 3.3V power
supply rail.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The clock API can't cope with unbalanced enables and disables and
we only enable in hw_params() but try to disable in shutdown.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
So far, the FLOAT PCM format is used only exclusivley set. But
this can be a combination with other formats.
This patch changes the parser to allow the FLOAT format in addition
to other PCM formats.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The device is a mono device but it can read two channel data and
many I2S controllers only understand 2 channels.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
alc882_auto_init_analog_input() sets the input pins to VREF-80 regardless
of the input pin types although it shouldn't be for line-in pins.
This patch fixes the behavior to follow other codecs.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Merge patch_alc882() and patch_alc883() to the former one since both
codecs have fairly similar connections but just a slight difference.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch tries to work around the problem of broken OMAP1510 PCM playback
pointer calculation by replacing DMA function call that incorrectly tries to
read the value form DMA hardware with a value computed locally from an
already maintained variable omap_runtime_data.period_index.
Tested on OMAP5910 based Amstrad Delta (E3) using work in progress ASoC
driver.
Based on linux-2.6-asoc.git v2.6.31-rc1.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The needed spin_event_timeout() macro is now merged in from the
powerpc tree, so these drivers are no longer broken. This reverts
commit 0c0e09e21a (ASoC: Mark MPC5200
AC97 as BROKEN until PowerPC merge issues are resolved)
Tested against 2.6.31-rc1.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Jon Smirl <jonsmirl@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
ALSA SoC drivers should be specify SND_SOC_AC97_BUS instead, not AC97_BUS.
Without SND_SOC_AC97_BUS defined, an AC97 device will not get correctly
registered on the AC97 bus, which prevents thinks like the WM9712
touchscreen driver from getting probed.
Tested against 2.6.31-rc1.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Jon Smirl <jonsmirl@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
mpu401_chk_version is called with a spin lock already held. Don't take it
again.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
During the changes to clean up / fix the realtek codec initialization
routines in commit 4a79ba34ca,
I forgot to add the check for ALC268 and ALC269.
This resulted in the missing EAPD and COEF setup for these codecs.
This patch adds the missing checks for these codecs.
Reference: bko#13633
http://bugzilla.kernel.org/show_bug.cgi?id=13633
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Check the hint "beep" in snd_hda_attach_beep_device() to avoid the beep
device creation if user doesn't want.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In ALSA 1.0.20, the comments were changed to say CMI8330 instead of AD1848.
The CMI8330 chip includes two codecs - AD1848 and SB16, so the comments were
correct and are misleading now. Revert them back.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Line In connector is set up as PIN_IN by default, using
VREF_HIZ. It is connected to both ADCs, so add it to both
input selectors.
Also add the ability to use the input mix (on a SoundBlaster
one would call this "What You Hear").
Signed-off-by: Tony Vroon <tony@linx.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
SoC dapm adds the suffix "Switch" to SND_SOC_DAPM_SWITCH controls,
removing word "Switch" from HandsfreeL/HandsfreeR widget name
for avoiding to duplicate it.
Signed-off-by: Misael Lopez Cruz <x0052729@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use kasprintf to allocate temporary devname string instead of a
fixed size string.
This fixes "FIXME" introduced on removal of BUS_ID_SIZE.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The microphone input and its volume register have only one channel, so
we have to make the corresponding mixer control a mono control.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
as long as the io channel number is not set by the driver, the card
is not visible from the ethersound network
Signed-off-by: Tim Blechmann <tim@klingt.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
I've built a small HTPC and had to add suspend/resume support in ice1724
driver. There seem to be 3 existing bugs related to that:
https://bugtrack.alsa-project.org/alsa-bug/view.php?id=4413https://bugtrack.alsa-project.org/alsa-bug/view.php?id=3748https://bugtrack.alsa-project.org/alsa-bug/view.php?id=2314
Due to hardware (un)availability, I only enabled the fix for Audiotrak
Prodigy HD2 card, which is installed in my HTPC. However, most of my code
should be reusable in the future on other ice1724-based cards as well (as
long as people add card-specific peices of code). The fix is currently based
on ALSA 1.0.20 and works on my MythBuntu 9.04 HTPC (using 2.6.28-11 kernel).
Signed-off-by: Igor Chernyshev <igor.ch75+alsa at gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Here's a patch on top of the others to use CREATIVE and ECTIVA
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
