commit 9f9666e653 upstream.
When resuming from system sleep states the driver issues following
warning on Intel hardware:
thunderbolt 0000:07:00.0: interrupt for TX ring 0 is already enabled
The reason for this is that the commit in question did not mask the ring
interrupt on Intel hardware leaving the interrupt active. Fix this by
masking it also in Intel hardware.
Reported-by: beld zhang <beldzhang@gmail.com>
Tested-by: beld zhang <beldzhang@gmail.com>
Closes: https://lore.kernel.org/linux-usb/ZHKW5NeabmfhgLbY@debian.me/
Fixes: c4af8e3fec ("thunderbolt: Clear registers properly when auto clear isn't in use")
Cc: stable@vger.kernel.org
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 70c2e03e9a upstream.
Both tb_xdomain_enable_paths() and tb_xdomain_disable_paths() expect -1,
not 0, if the corresponding ring is not needed. For this reason change
the driver to use correct value for the rings that are not needed.
Fixes: 180b068942 ("thunderbolt: Allow multiple DMA tunnels over a single XDomain connection")
Cc: stable@vger.kernel.org
Reported-by: Pengfei Xu <pengfei.xu@intel.com>
Tested-by: Pengfei Xu <pengfei.xu@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c4af8e3fec upstream.
When `QUIRK_AUTO_CLEAR_INT` isn't set, interrupt masking should be
cleared by writing to Interrupt Mask Clear (IMR) and interrupt
status should be cleared properly at shutdown/init.
This fixes an error where interrupts are left enabled during resume
from hibernation with `CONFIG_USB4=y`.
Fixes: 468c49f447 ("thunderbolt: Disable interrupt auto clear for rings")
Cc: stable@vger.kernel.org # v6.3
Reported-by: Takashi Iwai <tiwai@suse.de>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217343
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 58cdfe6f58 upstream.
cppcheck reports
drivers/thunderbolt/nhi.c:74:7: style: Local variable 'bit' shadows outer variable [shadowVariable]
int bit;
^
drivers/thunderbolt/nhi.c:66:6: note: Shadowed declaration
int bit = ring_interrupt_index(ring) & 31;
^
drivers/thunderbolt/nhi.c:74:7: note: Shadow variable
int bit;
^
For readablity rename the outer to interrupt_bit and the innner
to auto_clear_bit.
Fixes: 468c49f447 ("thunderbolt: Disable interrupt auto clear for ring")
Cc: stable@vger.kernel.org
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1716efdb07 upstream.
`ring_interrupt_index` doesn't change the data for `ring` so mark it as
const. This is needed by the following patch that disables interrupt
auto clear for rings.
Cc: Sanju Mehta <Sanju.Mehta@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cd0c1e582b upstream.
According to USB4 retimer specification, the process of firmware update
sequence requires issuing a SET_INBOUND_SBTX port operation that later
shall be followed by UNSET_INBOUND_SBTX port operation. This last step
is not currently issued by the driver but it is necessary to make sure
the retimers are put back to passthrough mode even during enumeration.
If this step is missing the link may not come up properly after
soft-reboot for example.
For this reason issue UNSET_INBOUND_SBTX after SET_INBOUND_SBTX for
enumeration and also when the NVM upgrade is run.
Reported-by: Christian Schaubschläger <christian.schaubschlaeger@gmx.at>
Link: https://lore.kernel.org/linux-usb/b556f5ed-5ee8-9990-9910-afd60db93310@gmx.at/
Cc: stable@vger.kernel.org
Signed-off-by: Gil Fine <gil.fine@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 468c49f447 upstream.
When interrupt auto clear is programmed, any read to the interrupt
status register will clear all interrupts. If two interrupts have
come in before one can be serviced then this will cause lost interrupts.
On AMD USB4 routers this has manifested in odd problems particularly
with long strings of control tranfers such as reading the DROM via bit
banging.
Instead of clearing interrupts automatically, clear the bit corresponding
to the given ring's interrupt in the ISR.
Fixes: 7a1808f82a ("thunderbolt: Handle ring interrupt by reading interrupt status register")
Cc: Sanju Mehta <Sanju.Mehta@amd.com>
Cc: stable@vger.kernel.org
Tested-by: Anson Tsao <anson.tsao@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d2d6ddf188 upstream.
In order to apply quirks based on certain adapter types move call to
tb_check_quirks() happen after the adapters are initialized. This should
not affect the existing quirks.
Cc: stable@vger.kernel.org
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c82510b1d8 upstream.
When tunneling aggregated USB3 (20 Gb/s) the bandwidth values that are
programmed to the ADP_USB3_CS_2 go higher than 4096 and that does not
fit anymore to the 12-bit field. Fix this by scaling the value using
the scale field accordingly.
Fixes: 3b1d8d577c ("thunderbolt: Implement USB3 bandwidth negotiation routines")
Cc: stable@vger.kernel.org
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e8ff07fb33 upstream.
We need to take minimum of both sides of the USB3 link into consideration,
not just the downstream port. Fix this by calling tb_usb3_max_link_rate()
instead.
Fixes: 0bd680cd90 ("thunderbolt: Add USB3 bandwidth management")
Cc: stable@vger.kernel.org
Acked-by: Yehezkel Bernat <YehezkelShB@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b60e31bf18 upstream.
If the boot firmware implements a connection manager of its own it may
create a DisplayPort tunnel and will be handed off to Linux connection
manager, but the DP OUT resource is not saved in the dp_resource list.
This patch adds tunnelled DP OUT port to the dp_resource list once the
DP tunnel is discovered.
Signed-off-by: Sanjay R Mehta <sanju.mehta@amd.com>
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Tested-by: Renjith Pananchikkal <Renjith.Pananchikkal@amd.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: "Limonciello, Mario" <Mario.Limonciello@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 43bddb26e2 upstream.
If the boot firmware implements connection manager of its own it may not
create the paths in the same way or order we do. For example it may
create first PCIe tunnel and then USB3 tunnel. When we restore our
tunnels (first de-activating them) we may be doing that over completely
different tunnels and that leaves them possibly non-functional. For this
reason we re-use the tunnel discovery functionality and find out all the
existing tunnels, and tear them down. Once that is done we can restore
our tunnels.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: "Limonciello, Mario" <Mario.Limonciello@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 54669e2f17 ]
As we are now enabling full end-to-end flow control to the Thunderbolt
networking driver, in order for it to work properly on second generation
Thunderbolt hardware (Falcon Ridge), we need to add back the workaround
that was removed with commit 53f13319d1 ("thunderbolt: Get rid of E2E
workaround"). However, this time we only apply it for Falcon Ridge
controllers as a form of an additional quirk. For non-Falcon Ridge this
does nothing.
While there fix a typo 'reqister' -> 'register' in the comment.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 5d2569cb4a upstream.
Software that has run before the USB4 CM in Linux runs may have disabled
hotplug events for a given lane adapter.
Other CMs such as that one distributed with Windows 11 will enable hotplug
events. Do the same thing in the Linux CM which fixes hotplug events on
"AMD Pink Sardine".
Cc: stable@vger.kernel.org
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 31f87f705b upstream.
If any software has interacted with the USB4 registers before the Linux
USB4 CM runs, it may have modified the plug events delay. It has been
observed that if this value too large, it's possible that hotplugged
devices will negotiate a fallback mode instead in Linux.
To prevent this, explicitly align the plug events delay with the USB4
spec value of 10ms.
Cc: stable@vger.kernel.org
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 14c7d90528 upstream.
Add support for Maple Ridge discrete USB4 host controller from Intel
which has a single USB4 port (versus the already supported dual port
Maple Ridge USB4 host controller).
Cc: stable@vger.kernel.org
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eb100b8fa8 upstream.
The received notification packet is held in pkg->buffer and not in pkg
itself. Fix this by using the correct buffer.
Fixes: 81a54b5e19 ("thunderbolt: Let the connection manager handle all notifications")
Cc: stable@vger.kernel.org
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9d2d0a5cf0 ]
Brad reported that on Apple hardware with Light Ridge or Falcon Ridge
controller, plugging in a chain of Thunderbolt displays (Light Ridge
based controllers) causes all kinds of tearing and flickering. The
reason for this is that on Thunderbolt 1 hardware there is no lane
bonding so we have two independent 10 Gb/s lanes, and currently Linux
tunnels both displays through the lane 1. This makes the displays to
share the 10 Gb/s bandwidth which may not be enough for higher
resolutions.
For this reason make the second tunnel go through the lane 0 instead.
This seems to match what the macOS connection manager is also doing.
Reported-by: Brad Campbell <lists2009@fnarfbargle.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Brad Campbell <lists2009@fnarfbargle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f3380cac0c ]
If protocol tunnels are already up when the driver is loaded, for
instance if the boot firmware implements connection manager of its own,
runtime PM reference count of the consumer devices behind the tunnel
might have been increased already before the device link is created but
the supplier device runtime PM reference count is not. This leads to a
situation where the supplier (the Thunderbolt driver) can runtime
suspend even if it should not because the corresponding protocol tunnel
needs to be up causing the devices to be removed from the corresponding
native bus.
Prevent this from happening by making both sides of the link runtime PM
active briefly. The pm_runtime_put() for the consumer (PCIe
root/downstream port, xHCI) then allows it to runtime suspend again but
keeps the supplier runtime resumed the whole time it is runtime active.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
The structleak plugin causes the stack frame size to grow immensely when
used with KUnit:
drivers/thunderbolt/test.c:1529:1: error: the frame size of 1176 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
Turn it off in this file.
Linus already split up tests in this file, so this change *should* be
redundant now.
Signed-off-by: Brendan Higgins <brendanhiggins@google.com>
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
The tb_test_credit_alloc_all() function had a huge number of
KUNIT_ASSERT() statements, all of which (though the magic of many many
layers of inscrutable macros) ended up allocating and initializing
various test assertion structures on the stack.
Don't do that. The kernel stack isn't infinite, and we have compiler
warnings (now errors) for the case where a stack frame grows too large.
Like it did here, by not an inconsiderable margin:
drivers/thunderbolt/test.c: In function ‘tb_test_credit_alloc_all’:
drivers/thunderbolt/test.c:2367:1: error: the frame size of 4500 bytes is larger than 2048 bytes [-Werror=frame-larger-than=]
2367 | }
| ^
Solve this similarly to the lib/test_scanf case: split out the tests
into several smaller functions, each just testing one particular tunnel
credit allocation.
This makes the i386 allyesconfig build work for me again.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Here is the big set of USB and Thunderbolt patches for 5.15-rc1.
Nothing huge in here, just lots of constant forward progress on a number
of different drivers and hardware support:
- more USB 4/Thunderbolt support added
- dwc3 driver updates and additions
- usb gadget fixes and addtions for new types
- udc gadget driver updates
- host controller updates
- removal of obsolete drivers
- other minor driver updates
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYS9+Tw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymqyQCgxWjp4VD9Ycbz1XsHRIkkERWj6WgAnRe4mCpG
n5csYXATbYUD0UdH0hru
=xZCV
-----END PGP SIGNATURE-----
Merge tag 'usb-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt updates from Greg KH:
"Here is the big set of USB and Thunderbolt patches for 5.15-rc1.
Nothing huge in here, just lots of constant forward progress on a
number of different drivers and hardware support:
- more USB 4/Thunderbolt support added
- dwc3 driver updates and additions
- usb gadget fixes and addtions for new types
- udc gadget driver updates
- host controller updates
- removal of obsolete drivers
- other minor driver updates
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (148 commits)
usb: isp1760: otg control register access
usb: isp1760: use the right irq status bit
usb: isp1760: write to status and address register
usb: isp1760: fix qtd fill length
usb: isp1760: fix memory pool initialization
usb: typec: tcpm: Fix spelling mistake "atleast" -> "at least"
usb: dwc2: Fix spelling mistake "was't" -> "wasn't"
usb: renesas_usbhs: Fix spelling mistake "faile" -> "failed"
usb: host: xhci-rcar: Don't reload firmware after the completion
usb: xhci-mtk: allow bandwidth table rollover
usb: mtu3: fix random remote wakeup
usb: mtu3: return successful suspend status
usb: xhci-mtk: Do not use xhci's virt_dev in drop_endpoint
usb: xhci-mtk: modify the SOF/ITP interval for mt8195
usb: xhci-mtk: add a member of num_esit
usb: xhci-mtk: check boundary before check tt
usb: xhci-mtk: update fs bus bandwidth by bw_budget_table
usb: xhci-mtk: fix issue of out-of-bounds array access
usb: xhci-mtk: support option to disable usb2 ports
usb: xhci-mtk: fix use-after-free of mtk->hcd
...
This includes following Thunderbolt/USB4 changes for the v5.15 merge
window:
* Include authorized value in the KOBJ_CHANGE event of a device router
* A couple of improvements to get the driver working also with the AMD
USB4 host controller.
All these have been in linux-next with no reported issues.
-----BEGIN PGP SIGNATURE-----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=1bPR
-----END PGP SIGNATURE-----
Merge tag 'thunderbolt-for-v5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt into usb-next
Mika writes:
thunderbolt: Changes for v5.15 merge window
This includes following Thunderbolt/USB4 changes for the v5.15 merge
window:
* Include authorized value in the KOBJ_CHANGE event of a device router
* A couple of improvements to get the driver working also with the AMD
USB4 host controller.
All these have been in linux-next with no reported issues.
* tag 'thunderbolt-for-v5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt:
thunderbolt: Fix port linking by checking all adapters
thunderbolt: Do not read control adapter config space
thunderbolt: Handle ring interrupt by reading interrupt status register
thunderbolt: Add vendor specific NHI quirk for auto-clearing interrupt status
thunderbolt: Add authorized value to the KOBJ_CHANGE uevent
In tb_switch_default_link_ports(), while linking of ports,
only odd-numbered ports (1,3,5..) are considered and even-numbered
ports are not considered.
AMD host router has lane adapters at 2 and 3 and link ports at adapter 2
is not considered due to which lane bonding gets disabled.
Hence added a fix such that all ports are considered during
linking of ports.
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Signed-off-by: Sanjay R Mehta <sanju.mehta@amd.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Adapter 0 is the control adapter and as per USB4 spec in section 2.2.6.2
control Adapters do not have an adapter configuration space.
For this reason skip reading adapter config space in tb_port_init() when
the port number is 0. This actually simplifies the rest of the function
as we don't need to check for the port->port == 0 anymore.
While there drop the extra empty line at the end of the function.
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Signed-off-by: Sanjay R Mehta <sanju.mehta@amd.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
As per USB4 specification by default "Disable ISR Auto-Clear" bit is set
to zero and the Tx/Rx ring interrupt status needs to be cleared.
Hence handle it by reading the interrupt status register (ISR) in the
MSI-X handler.
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Signed-off-by: Sanjay R Mehta <sanju.mehta@amd.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Introduce nhi_check_quirks() routine to handle any vendor specific quirks
to manage a hardware specific implementation.
On Intel hardware the USB4 controller supports clearing the interrupt
status register automatically right after it is being issued. For this
reason add a new quirk that does that on all Intel hardware.
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Signed-off-by: Sanjay R Mehta <sanju.mehta@amd.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
For security reasons, we would like to monitor and track when the
Thunderbolt devices are authorized and deauthorized (i.e. when the
Thunderbolt sysfs "authorized" attribute changes). Currently the
userspace gets a udev change notification when there is a change, but
the state may have changed (again) by the time we look at the authorized
attribute in sysfs. So an authorization event may go unnoticed. Thus
make it easier by informing the actual change (new value of authorized
attribute) in the udev change notification.
The change is included as a key value "authorized=<val>" where <val>
is the new value of sysfs attribute "authorized", and is described at
Documentation/ABI/testing/sysfs-bus-thunderbolt under
/sys/bus/thunderbolt/devices/.../authorized.
Signed-off-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The driver core ignores the return value of this callback because there
is only little it can do when a device disappears.
This is the final bit of a long lasting cleanup quest where several
buses were converted to also return void from their remove callback.
Additionally some resource leaks were fixed that were caused by drivers
returning an error code in the expectation that the driver won't go
away.
With struct bus_type::remove returning void it's prevented that newly
implemented buses return an ignored error code and so don't anticipate
wrong expectations for driver authors.
Reviewed-by: Tom Rix <trix@redhat.com> (For fpga)
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Cornelia Huck <cohuck@redhat.com> (For drivers/s390 and drivers/vfio)
Acked-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> (For ARM, Amba and related parts)
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Chen-Yu Tsai <wens@csie.org> (for sunxi-rsb)
Acked-by: Pali Rohár <pali@kernel.org>
Acked-by: Mauro Carvalho Chehab <mchehab@kernel.org> (for media)
Acked-by: Hans de Goede <hdegoede@redhat.com> (For drivers/platform)
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-By: Vinod Koul <vkoul@kernel.org>
Acked-by: Juergen Gross <jgross@suse.com> (For xen)
Acked-by: Lee Jones <lee.jones@linaro.org> (For mfd)
Acked-by: Johannes Thumshirn <jth@kernel.org> (For mcb)
Acked-by: Johan Hovold <johan@kernel.org>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> (For slimbus)
Acked-by: Kirti Wankhede <kwankhede@nvidia.com> (For vfio)
Acked-by: Maximilian Luz <luzmaximilian@gmail.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> (For ulpi and typec)
Acked-by: Samuel Iglesias Gonsálvez <siglesias@igalia.com> (For ipack)
Acked-by: Geoff Levand <geoff@infradead.org> (For ps3)
Acked-by: Yehezkel Bernat <YehezkelShB@gmail.com> (For thunderbolt)
Acked-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> (For intel_th)
Acked-by: Dominik Brodowski <linux@dominikbrodowski.net> (For pcmcia)
Acked-by: Rafael J. Wysocki <rafael@kernel.org> (For ACPI)
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org> (rpmsg and apr)
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> (For intel-ish-hid)
Acked-by: Dan Williams <dan.j.williams@intel.com> (For CXL, DAX, and NVDIMM)
Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com> (For isa)
Acked-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (For firewire)
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> (For hid)
Acked-by: Thorsten Scherer <t.scherer@eckelmann.de> (For siox)
Acked-by: Sven Van Asbroeck <TheSven73@gmail.com> (For anybuss)
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> (For MMC)
Acked-by: Wolfram Sang <wsa@kernel.org> # for I2C
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Finn Thain <fthain@linux-m68k.org>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20210713193522.1770306-6-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the big set of USB and Thunderbolt patches for 5.14-rc1.
Nothing major here just lots of little changes for new hardware and
features. Highlights are:
- more USB 4 support added to the thunderbolt core
- build warning fixes all over the place
- usb-serial driver updates and new device support
- mtu3 driver updates
- gadget driver updates
- dwc3 driver updates
- dwc2 driver updates
- isp1760 host driver updates
- musb driver updates
- lots of other tiny things.
Full details are in the shortlog.
All of these have been in linux-next for a while now with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYOM3EA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynGewCeMg7YvtCnqFBNebC+GfKpFTgWxO4AnAppjSrZ
RPGQgfZdWmx7daCXWbSK
=u68a
-----END PGP SIGNATURE-----
Merge tag 'usb-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt updates from Greg KH:
"Here is the big set of USB and Thunderbolt patches for 5.14-rc1.
Nothing major here just lots of little changes for new hardware and
features. Highlights are:
- more USB 4 support added to the thunderbolt core
- build warning fixes all over the place
- usb-serial driver updates and new device support
- mtu3 driver updates
- gadget driver updates
- dwc3 driver updates
- dwc2 driver updates
- isp1760 host driver updates
- musb driver updates
- lots of other tiny things.
Full details are in the shortlog.
All of these have been in linux-next for a while now with no reported
issues"
* tag 'usb-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (223 commits)
phy: qcom-qusb2: Add configuration for SM4250 and SM6115
dt-bindings: phy: qcom,qusb2: document sm4250/6115 compatible
dt-bindings: usb: qcom,dwc3: Add bindings for sm6115/4250
USB: cdc-acm: blacklist Heimann USB Appset device
usb: xhci-mtk: allow multiple Start-Split in a microframe
usb: ftdi-elan: remove redundant continue statement in a while-loop
usb: class: cdc-wdm: return the correct errno code
xhci: remove redundant continue statement
usb: dwc3: Fix debugfs creation flow
usb: gadget: hid: fix error return code in hid_bind()
usb: gadget: eem: fix echo command packet response issue
usb: gadget: f_hid: fix endianness issue with descriptors
Revert "USB: misc: Add onboard_usb_hub driver"
Revert "of/platform: Add stubs for of_platform_device_create/destroy()"
Revert "usb: host: xhci-plat: Create platform device for onboard hubs in probe()"
Revert "arm64: dts: qcom: sc7180-trogdor: Add nodes for onboard USB hub"
xhci: solve a double free problem while doing s4
xhci: handle failed buffer copy to URB sg list and fix a W=1 copiler warning
xhci: Add adaptive interrupt rate for isoch TRBs with XHCI_AVOID_BEI quirk
xhci: Remove unused defines for ERST_SIZE and ERST_ENTRIES
...
This KUnit update for Linux 5.14-rc1 consists of fixes and features:
-- add support for skipped tests
-- introduce kunit_kmalloc_array/kunit_kcalloc() helpers
-- add gnu_printf specifiers
-- add kunit_shutdown
-- add unit test for filtering suites by names
-- convert lib/test_list_sort.c to use KUnit
-- code organization moving default config to tools/testing/kunit
-- refactor of internal parser input handling
-- cleanups and updates to documentation
-- code cleanup related to casts
-----BEGIN PGP SIGNATURE-----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=5QAv
-----END PGP SIGNATURE-----
Merge tag 'linux-kselftest-kunit-fixes-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull KUnit update from Shuah Khan:
"Fixes and features:
- add support for skipped tests
- introduce kunit_kmalloc_array/kunit_kcalloc() helpers
- add gnu_printf specifiers
- add kunit_shutdown
- add unit test for filtering suites by names
- convert lib/test_list_sort.c to use KUnit
- code organization moving default config to tools/testing/kunit
- refactor of internal parser input handling
- cleanups and updates to documentation
- code cleanup related to casts"
* tag 'linux-kselftest-kunit-fixes-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest: (29 commits)
kunit: add unit test for filtering suites by names
kasan: test: make use of kunit_skip()
kunit: test: Add example tests which are always skipped
kunit: tool: Support skipped tests in kunit_tool
kunit: Support skipped tests
thunderbolt: test: Reinstate a few casts of bitfields
kunit: tool: internal refactor of parser input handling
lib/test: convert lib/test_list_sort.c to use KUnit
kunit: introduce kunit_kmalloc_array/kunit_kcalloc() helpers
kunit: Remove the unused all_tests.config
kunit: Move default config from arch/um -> tools/testing/kunit
kunit: arch/um/configs: Enable KUNIT_ALL_TESTS by default
kunit: Add gnu_printf specifiers
lib/cmdline_kunit: Remove a cast which are no-longer required
kernel/sysctl-test: Remove some casts which are no-longer required
thunderbolt: test: Remove some casts which are no longer required
mmc: sdhci-of-aspeed: Remove some unnecessary casts from KUnit tests
iio: Remove a cast in iio-test-format which is no longer required
device property: Remove some casts in property-entry-test
Documentation: kunit: Clean up some string casts in examples
...
Partially revert "thunderbolt: test: Remove some casts which are no
longer required". It turns out that typeof() doesn't support bitfields,
so these still need to be cast to the appropriate enum.
The only mention of typeof() and bitfields I can find is in the proposal
to standardise them:
http://www.open-std.org/jtc1/sc22/wg14/www/docs/n2619.htm
This was caught by the kernel test robot:
https://lists.01.org/hyperkitty/list/kbuild-all@lists.01.org/thread/FDKBHAV7QNLNFU5NBI2RKV56DWDSOLGM/
Fixes: 8f0877c26e ("thunderbolt: test: Remove some casts which are no longer required")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: David Gow <davidgow@google.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
With some of the stricter type checking in KUnit's EXPECT macros
removed, several casts in the thunderbolt KUnit tests are no longer
required.
Remove the unnecessary casts, making the conditions clearer.
Signed-off-by: David Gow <davidgow@google.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
DROM for USB4 host/device has a shorter header than Thunderbolt DROM
header. This patch addresses host/device with USB4 DROM (According to spec:
Universal Serial Bus 4 (USB4) Device ROM Specification, Rev 1.0, Feb-2021).
While there correct the data_len field to be 12 bits and rename
__unknown1 to reserved following the spec.
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Alder Lake has the same integrated Thunderbolt/USB4 controller as
Intel Tiger Lake. By default it is still using firmware based connection
manager so we can use most of the Tiger Lake flows.
Add the Alder Lake PCI IDs to the driver list of supported devices.
Signed-off-by: Azhar Shaikh <azhar.shaikh@intel.com>
Reviewed-by: Yehezkel Bernat <YehezkelShB@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
This include is not needed so drop it.
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Yehezkel Bernat <YehezkelShB@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
In Intel Tiger Lake and beyond it takes some time after the force power
is set until the firmware connection manager is ready. So instead of
reading it once we poll it for 10ms before giving up.
Signed-off-by: Gil Fine <gil.fine@intel.com>
Reviewed-by: Yehezkel Bernat <YehezkelShB@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
We only need to set up the device links when software connection manager
path is used. The firmware connection manager does not need them and if
they are present they may even cause problems.
Reviewed-by: Yehezkel Bernat <YehezkelShB@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
We should not dereference ->dual_link_port if it is NULL and lane bonding
is requested. For this reason move lane bonding configuration happen
inside the block where ->dual_link_port != NULL.
Fixes: 54509f5005 ("thunderbolt: Add KUnit tests for path walking")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Yehezkel Bernat <YehezkelShB@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
If the NVM authentication fails immediately, like if the firmware
detects that the image is not valid for some reason, better to read the
status once and if set to non-zero fail the operation accordingly.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The same way we support these two operations for USB4 routers we can
extend the retimer NVM operations to support retimers also.
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Co-developed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It may be useful if the actual NVM authentication can be delayed to be
run later, for instance when the user logs out. For this reason add a
new NVM operation (AUHENTICATE_ONLY) that just triggers the authentication
procedure over whatever was written to the NVM storage.
This is not supported with Thunderbolt 1-3 devices, though.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently these write ops are used for updating router firmware images
only. Moving to tb.h helps the retimers also to use the same ops.
Also add tb_ prefix to the enum while there.
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With help from platform firmware (ACPI) it is possible to power on
retimers even when there is no USB4 link (e.g nothing is connected to
the USB4 ports). This allows us to bring the USB4 sideband up so that we
can access retimers and upgrade their NVM firmware.
If the platform has support for this, we expose two additional
attributes under USB4 ports: offline and rescan. These can be used to
bring the port offline, rescan for the retimers and put the port online
again. The retimer NVM upgrade itself works the same way than with cable
connected.
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Co-developed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When accessing retimers when there is no cable connected we are going to
need additional USB4 port operations. First the port needs to be put
into offline mode, and then the sideband channel transactions must be
enabled on the SBTX line. This adds support for these operations.
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Typically retimers can be accessed only when the USB4 link is up (e.g
there is a cable connected). However, sometimes it is useful to be able
to access retimers even if there is nothing connected to the USB4 port.
For instance we may still want to be able to upgrade the retimer NVM
firmware even if the user does not have any USB4 devices. This is
something that USB4 spec leaves to implementers.
In case of ACPI based systems, we can support this by providing a
special _DSM method under each USB4 port. This _DSM can be used to turn
on power to on-board retimers (and cycle it through different modes so
that the sideband becomes usable).
This patch adds support for this _DSM and makes the functionality
available to the rest of the driver through tb_acpi_power_[on|off]_retimers().
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Co-developed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Create devices for each USB4 port. This is needed when we add retimer
access when there is no device connected but may be useful for other
purposes too following what USB subsystem does. This exports a single
attribute "link" that shows the type of the USB4 link (or "none" if
there is no cable connected).
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The upstream port can be connected to any previous generation
Thunderbolt port so logging as "TBT" is more accurate than "TBT3.
No functional changes.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
