change WA_SEGS_MAX to a number that is legal according to the WUSB
spec.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a quirk for Alereon HWA devices to concatenate the frames of isoc
transfer requests.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Combine multiple isoc frames in a single transfer request. This allows
the HWA to take advantage of bursting to deliver data to endpoints
whose logical service interval is less than the minimum wireless USB
service interval of 4ms. Wireless audio quality is much improved after
this update.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For isochronous endpoints, set the RPIPE wMaxPacketSize value using
wOverTheAirPacketSize from the endpoint companion descriptor instead of
wMaxPacketSize from the normal endpoint descriptor.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cbaf_probe() does cbaf->usb_dev = usb_get_dev(interface_to_usbdev(iface)),
but there is no usb_put_dev() anywhere in cbaf.
The patch adds usb_put_dev() to cbaf_disconnect() and to an error path in cbaf_probe().
Also it adds missed usb_put_intf(iface) to the error path.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do not overwrite the multi-byte fields of usb_wa_descriptor with their
cpu format values after reading the descriptor. Leave the values as
__le16 and swap on use. This is more consistent with other uses of USB
descriptors.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch serializes access to the HWA data transfer out (DTO)
endpoint. This prevents a situation where two transfer requests being
sent concurrently to separate downstream endpoints could interleave
their transfer request and transfer data packets causing data
corruption. The transfer processing code will now attempt to acquire
the DTO resource before sending a transfer to the HWA. If it cannot
acquire the resource, the RPIPE that the transfer is assigned to will
be placed on a waiting list. When the DTO resource is released, the
actor releasing the resource will serivce the RPIPEs that are waiting.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These aren't necessary after switch and if blocks.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes compile warnings on 64-bit builds that were introduced
by the recent isoc changes.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Reported-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for isochronous out transfers to the HWA. The
primary changes are:
1. Add a isoc_pack_desc_urb field to struct wa_seg. This urb is used
to send the isochronous packet info message to the HWA which describes
the isoc data segment(s) that will be sent as the payload of the
transfer request.
2. Use the URB iso_frame_desc field to populate the isochronous packet
info message and data segments sent to the HWA.
3. After the data is sent and transfer result is returned from the
HWA, read the isoc packet status message from the HWA. The contents of
the isoc packet status message are used to set the iso_frame_desc
status and actual_length fields in the original isoc URB. This feature
required the addition of a some state tracking variables in struct wahc
so the dti_urb knows what type of packet it expects to receive next.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch sets the RPIPE bOverTheAirInterval field for RPIPES which
refer to isochronous endpoints.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch modifies wa_urb_enqueue to return an error and not call the
urb completion routine if it failed to enqueue the urb because the HWA
device is gone. This prevents a stack overflow due to infinite
submit/complete recursion when unplugging the HWA while connected to a
HID device.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix a build warning found by the kbuild test robot in the most recent
wusbcore patches.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch updates URB dequeue handling in wusbcore to make it more
reliable when a URB has been broken up into multiple WUSB transfer
request segments.
In wa_urb_dequeue, don't mark segments in the WA_SEG_SUBMITTED,
WA_SEG_PENDING or WA_SEG_DTI_PENDING states as completed if an ABORT
TRANSFER request was sent to the HWA to clean them up. Wait for the
HWA to return a transfer result indicating that it has aborted the
request before cleaning it up. This prevents the DTI state machine
from losing track of transfers and avoids confusion in the case where a
read transfer segment is dequeued after the driver has received the
transfer result but before the data is received.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Include the xfer_id in debug prints for transfers and transfer segments.
This makes it much easier to correlate debug logs to USB analyzer logs.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a new function to get the xfer ID in little endian format
(wa_xfer_id_le32), and use it instead of wa_xfer_id where appropriate.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes two cases where error handling code was freeing memory
but not setting the pointer to NULL. This could lead to a double free
in the HWA shutdown code.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clean up the SG list after transfer completetion for out transfers if one
was created by the HWA.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch updates __wa_xfer_setup_segs error path to only clean up the
xfer->seg entry that it failed to create and then set that entry to
NULL. wa_xfer_destroy will clean up the remaining xfer->segs that were
fully created. It also moves the code to create the dto sg list to an
out of line function to make __wa_xfer_setup_segs easier to read. Prior
to this change, __wa_xfer_setup_segs would clean up all entries in the
xfer->seg array in case of an error but it did not set them to NULL.
This resulted in a double free when wa_xfer_destroy was eventually
called by the higher level error handler.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If __wa_xfer_setup fails, it can leave a partially constructed wa_xfer
object. The error handling code eventually calls wa_xfer_destroy which
does not check for NULL before dereferencing xfer->seg which could cause
a kernel panic. This change also makes sure to free xfer->seg which was
being leaked for all transfers before this change.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rename xfer_result to dti_buf and xfer_result_size to dti_buf_size in
struct wahc. The dti buffer will also be used for isochronous status
packets once isochronous transfers are supported.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rename urb to tr_urb in struct wa_seg to make it clear that the urb is
used for the transfer request.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In wa_seg_init, use usb_init_urb to init the URB object contained in the
transfer segment instead of initializing it manually. Use kmalloc to
allocate the memory for segment instead of kzalloc and then use memset
to set the non-URB portion of the transfer segment struct to 0 since
that was already done by usb_init_urb.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The check to free the URB was the opposite of the correct case. This
patch removes the check altogether since the ptr will be NULL if the URB
was not allocated. Also use usb_free_urb instead of usb_put_urb.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use usb_free_urb instead of kfree in error path and point to the correct
URB. Also remember to clean up the sg list for the URB if it was allocated.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the HWA encounters a STALL on a control endpoint, it should clear the
RPIPE_STALL feature on the RPIPE before processing the next transfer
request. Otherwise, all transfer requests on that endpoint after the
first STALL will fail because the RPIPE is still in the halted state.
This also removes the unneccessary call to spin_lock_irqsave for a nested
lock that was present in the first patch.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes a kernel panic that can occur when disconnecting a
wireless USB->serial device. When the serial device disconnects, the
device cleanup procedure ends up calling usb_hcd_disable_endpoint on the
serial device's endpoints. The wusbcore uses the ABORT_RPIPE command to
abort all transfers on the given endpoint but it does not properly give
back the URBs when the transfer results return from the HWA. This patch
prevents the transfer result processing code from bailing out when it sees
a WA_XFER_STATUS_ABORTED result code so that these urbs are flushed
properly by usb_hcd_disable_endpoint. It also updates wa_urb_dequeue to
handle the case where the endpoint has already been cleaned up when
usb_kill_urb is called which is where the panic originally occurred.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
wa_urb_enqueue_run locks and unlocks its list lock as it traverses the
list of queued transfers. This was done to prevent deadlocking due to
acquiring locks in reverse order in different places. The problem is that
releasing the lock during the list traversal could allow the dequeue
routine to corrupt the list while it is being iterated over. This patch
moves all list entries to a temp list while holding the list lock, then
traverses the temp list with no lock held.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The hub_status_data function on the wireless USB root hub controller
(wusbhc_rh_status_data) always returns a positive value even if no ports
have changed. This patch updates wusbhc_rh_status_data to only return a
positive value if the root hub status needs to be queried. The current
implementation can also leave the upper bits of the port bitmap
uninitialized if wusbhc->ports_max is not one less than an even multiple
of 8. This patch fixes that as well by initializing the buffer to 0.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes a race condition that caused the HWA_HC interface probe
function to occasionally fail. The HWA_HC would attempt to register
itself with the HWA_RC by searching for a uwb_rc class device with the
same parent device ptr. If the probe function for the HWA_RC interface
had yet to run, the uwb_rc class device would not have been created
causing the look up to fail and the HWA_HC probe function to return an
error causing the device to be unusable.
The fix is for the HWA to delay registering with the HWA_RC until
receiving the command from userspace to start the wireless channel. It
is the responsibility of userspace to ensure that the uwb_rc class
device has been created before starting the HWA channel.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds a sysfs attribute for the wireless host controller
transaction retry count. It also changes the default value from 15
retries to infinite retries because the driver currently does not handle
retry errors gracefully.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds a sysfs attribute for the wireless USB host controller
device notification transmit slot(DNTS) count and interval. It also
changes the defaults from 16 slots in every MMC to a more reasonable 4
slots every 2ms.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for scatter gather DMA to the wire adapter and
updates the HWA to advertise support for SG transfers. This allows the
block layer to submit transfer requests to the HWA HC without first
breaking them up into PAGE_SIZE requests.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No action is needed for the HWA_NOTIF_BPST_ADJ event. Ignore it instead
of printing a warning to the log since these events can happen dozens of
times per second.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds the HWA specific members to struct usb_rpipe_descriptor
and sets them correctly based on the wireless endpoint compananion
descriptor.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suspend and resume are not currently supported on the wireless root hub.
Remove the suspend and resume op functions in the host controller driver
to avoid constant error messages in the system log.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch reduces the keepalive threshold of WUSB host controllers from
timeout/2 to timeout/3. The keepalive timer fires every timeout/2 ms, but
due to rounding errors and jitter, the host may decide not to send a
keepalive at timeout/2. By the time the next timer fires, a full timeout
period may have expired causing the device to be disconnected without ever
having been sent a keepalive. Changing the keepalive threshold to
timeout/3 ensures that at least one keepalive will be sent before a device
is disconnected. The patch also updates the code to use msecs_to_jiffies
consistently.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes the depends on USB from all config symbols in
drivers/usb/host/Kconfig and replace that with an if USB / endif block
as suggested by Alan Stern. Some source ... Kconfig lines have been
shuffled around to permit a better regroupment of the Kconfig files
depending on "config USB" item. No functionnal change is introduced.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
1) It didn't free xfer->seg[0] so there was a leak.
2) xfer->seg[cnt] can be NULL.
3) Use usb_free_urb() for ->dto_urb instead of kfree().
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "wusb_cap_descr_default" is never used. GCC doesn't complain about
it because we have that line ".bLength = sizeof(wusb_cap_descr_default)"
inside the definition itself. Clang complains though.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As discussed at the kernel summit this year, CONFIG_EXPERIMENTAL means
nothing, so let's get rid of it.
Acked-by: Felipe Balbi <balbi@ti.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: David Herrmann <dh.herrmann@googlemail.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Neil Zhang <zhangwm@marvell.com>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert a 0 error return code to a negative one, as returned elsewhere in the
function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret;
expression e,e1,e2,e3,e4,x;
@@
(
if (\(ret != 0\|ret < 0\) || ...) { ... return ...; }
|
ret = 0
)
... when != ret = e1
*x = \(kmalloc\|kzalloc\|kcalloc\|devm_kzalloc\|ioremap\|ioremap_nocache\|devm_ioremap\|devm_ioremap_nocache\)(...);
... when != x = e2
when != ret = e3
*if (x == NULL || ...)
{
... when != ret = e4
* return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do not leak memory by updating pointer with potentially NULL realloc return value.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix UWB/WUSB kconfig error by changing 'select' to 'depends on'.
drivers/usb/wusbcore/Kconfig:4:error: recursive dependency detected!
drivers/usb/wusbcore/Kconfig:4: symbol USB_WUSB is selected by USB_HWA_HCD
drivers/usb/host/Kconfig:559: symbol USB_HWA_HCD depends on UWB
drivers/uwb/Kconfig:5: symbol UWB is selected by USB_WUSB
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix the following warning:
warning: (USB_WUSB) selects UWB which has unmet direct dependencies (EXPERIMENTAL && PCI)
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The advantage of kcalloc is, that will prevent integer overflows which could
result from the multiplication of number of elements and size and it is also
a bit nicer to read.
The semantic patch that makes this change is available
in https://lkml.org/lkml/2011/11/25/107
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This converts the drivers in drivers/usb/* to use the
module_usb_driver() macro which makes the code smaller and a bit
simpler.
Added bonus is that it removes some unneeded kernel log messages about
drivers loading and/or unloading.
Cc: Simon Arlott <cxacru@fire.lp0.eu>
Cc: Duncan Sands <duncan.sands@free.fr>
Cc: Matthieu CASTET <castet.matthieu@free.fr>
Cc: Stanislaw Gruszka <stf_xl@wp.pl>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: Oliver Neukum <oliver@neukum.name>
Cc: Juergen Stuber <starblue@users.sourceforge.net>
Cc: Cesar Miquel <miquel@df.uba.ar>
Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Cc: Matthew Wilcox <willy@linux.intel.com>
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Lucas De Marchi <lucas.demarchi@profusion.mobi>
Cc: Michael Hund <mhund@ld-didactic.de>
Cc: Zack Parsons <k3bacon@gmail.com>
Cc: Melchior FRANZ <mfranz@aon.at>
Cc: Tomoki Sekiyama <tomoki.sekiyama@gmail.com>
Cc: Dan Carpenter <error27@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
