Keys: 'right arrow', 'up arrow' and 'select' were mapped
wrongly. This patch corrects them.
This patch also adds one missing key present in the board,
currently I added it as 'unknown' key, as I am not able to
find proper description for this key.
One key entry (r: 7, c: 5) is present in the keymap, which
is really not present in the board, removing it.
Signed-off-by: Vimal Singh <vimalsingh@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit f62349ee97 makes it possible to
have some other than first uart port as ttyS0, which breaks the workaround
serial_in_override() function which will try to address the first uart
port (for ttyS0) and not the one that was initialized.
Signed-off-by: Alexander Shishkin <virtuoso@slind.org>
CC: Mika Westerberg <ext-mika.1.westerberg@nokia.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 9905a43b made struct backlight_ops const. Omap was
setting check_fb dynamically, which caused the following
compile error:
drivers/video/backlight/omap1_bl.c: In function 'omapbl_probe':
drivers/video/backlight/omap1_bl.c:142: error: assignment of read-only variable 'omapbl_ops'
Turns out pdata->check_fb is not being used, so just remove
it to fix the compile.
Cc: Emese Revfy <re.emese@gmail.com>
Cc: Richard Purdie <rpurdie@linux.intel.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 35c9049b27 added
drivers/spi/omap_spi_100k.c.
This patch add the related clocks and pin muxing
entries to make the driver work on omap7xx platforms.
Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Some chips, namely any OMAP1 chips using METHOD_MPUIO,
OMAP15xx and OMAP7xx, cannot be setup to respond to on-chip GPIO
interrupts in both rising and falling edge directions -- they can
only respond to one direction or the other, depending on how the
ICR is configured.
Additionally, current code forces rising edge detection if both
flags are specified:
if (trigger & IRQ_TYPE_EDGE_RISING)
l |= 1 << gpio;
else if (trigger & IRQ_TYPE_EDGE_FALLING)
l &= ~(1 << gpio);
else
goto bad;
This change implements a toggle function that will modify the ICR
to flip the direction of interrupt for IRQs that are requested with
both rising and falling flags. The toggle function is not called
for chips and GPIOs it does not apply to through the use of a flip_mask
that's added on a per-bank basis. The mask is only set for those
GPIOs where a toggle is necessary. Edge detection starts out the
same as above with FALLING mode first.
The toggle happens on EACH interrupt; without it, we have the
following sequence of actions on GPIO transition:
ICR GPIO Result
0x1 0 -> 1 (rising) Interrupt
0x1 1 -> 0 (falling) No interrupt
(set ICR to 0x0 manually)
0x0 0 -> 1 (rising) No interrupt
0x0 1 -> 0 (falling) Interrupt
That is, with the ICR set to 1 for a gpio, only rising edge interrupts
are caught, and with it set to 0, only falling edge interrupts are
caught. If we add in the toggle, we get this:
ICR GPIO Result
0x1 0 -> 1 (rising) Interrupt (ICR set to 0x0)
0x0 1 -> 0 (falling) Interrupt (ICR set to 0x1)
0x1 0 -> 1 ...
so, both rising and falling are caught, per the request for both
(IRQ_TYPE_EDGE_RISING | IRQ_TYPE_EDGE_FALLING).
Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In its current form, the omap_mcbsp_request() function can return after
irq_request() failure without any cleanups, effectively locking out the port
forever with clocks left running. Fix it.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] __per_cpu_idtrs[] is a memory hog
[IA64] sanity in #include files. Move fnptr to types.h
[IA64] use helpers for rlimits
[IA64] cpumask_of_node() should handle -1 as a node
Fix the following warning, which appears when the register dump for a
faulting process is printed in a kernel with SMP, DEBUG_PREEMPT, and
DEBUG_USER (with user_debug=31) enabled:
BUG: using smp_processor_id() in preemptible [00000000] code: init/1
caller is __show_regs+0x18/0x234
Backtrace:
[<c0159e5c>] (dump_backtrace+0x0/0x114) from [<c01faf30>] (dump_stack+0x18/0x1c)
r6:c781a000 r5:c0157544 r4:00000001 r3:00000000
[<c01faf18>] (dump_stack+0x0/0x1c) from [<c01e5230>] (debug_smp_processor_id+0xc4/0xf8)
[<c01e516c>] (debug_smp_processor_id+0x0/0xf8) from [<c0157544>] (__show_regs+0x18/0x234)
r6:c781bfb0 r5:00000000 r4:c781bfb0 r3:00000000
[<c015752c>] (__show_regs+0x0/0x234) from [<c01577a0>] (show_regs+0x40/0x50)
[<c0157760>] (show_regs+0x0/0x50) from [<c015c968>] (__do_user_fault+0x5c/0xa4)
r4:c781c000 r3:00000000
[<c015c90c>] (__do_user_fault+0x0/0xa4) from [<c015cbe0>] (do_page_fault+0x1b4/0x1e4)
r7:00000000 r6:00010000 r5:c781bfb0 r4:c781c000
[<c015ca2c>] (do_page_fault+0x0/0x1e4) from [<c01554c8>] (do_DataAbort+0x3c/0xa0)
[<c015548c>] (do_DataAbort+0x0/0xa0) from [<c01560c4>] (ret_from_exception+0x0/0x10)
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This updates the U300 defconfig to include the DMA driver merged
in 2.6.33-rc1 and adds a codepage that's needed to mount VFAT MMC
cards as default. The rest is new config options.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Make registers unsigned for kernel space. This is important for
example in the perf events where the PC is stored into a u64. We
don't want it sign extended so make the regs unsigned to prevent
casts throughout the kernel.
Signed-off-by: Jamie Iles <jamie.iles@picochip.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Somehow, strange characters made their way zaurus gpio .desc
fields. Fix it.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Stanislav Brabec <utx@penguin.cz>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
__per_cpu_idtrs is statically allocated ... on CONFIG_NR_CPUS=4096
systems it hogs 16MB of memory. This is way too much for a quite
probably unused facility (only KVM uses dynamic TR registers).
Change to an array of pointers, and allocate entries as needed on
a per cpu basis. Change the name too as the __per_cpu_ prefix is
confusing (this isn't a classic <linux/percpu.h> type object).
Signed-off-by: Tony Luck <tony.luck@intel.com>
In blackfin, kgdb is running in delayed exception IRQ5 other than in
exception IRQ3 directly. Register reti other than retx in pt_regs is
the kgdb return address. So, don't put PC in gdb_regs into retx.
CC: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Sonic Zhang <sonic.adi@gmail.com>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Blackfin needs it own arch specific probe_kernel_read() and
probe_kernel_write().
This was moved out of the kgdb code and into the
arch/blackfin/maccess.c, because it is a generic kernel api.
The arch specific kgdb.c for blackfin was cleaned of all functions
which exist in the kgdb core that do the same thing after resolving
the probe_kernel_read() and probe_kernel_write(). This also
eliminated the need for most of the #include's.
CC: Sonic Zhang <sonic.adi@gmail.com>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
There is a possibility of a loop happening in the PLL output clock
chain on the S3C64XX series. clk_mpll's parent was set to be
clk_mout_mpll, but this is fed from clk_fout_epll (which is also
clk_mpll).
clk_mpll is meant to be the output from the MPLL, and clk_mout_mpll
is a seperate clock derived from the mux of clk_mpll and clk_fin_mpll
and thus should be considered a seperate clock.
Anything using clk_mpll directly really should not be relying on this
being the clock that is eventually routed to a peripheral, so remove the
loop and ensure that the clocks accurately represent the clock chain
in the device.
The clk_mpll is not being used outside of the s3c6400-clock.c code, so
this change should not break anything else.
Do the same for the EPLL.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The current code will load the stack size and protection markings, but
then only use the markings in the MMU code path. The NOMMU code path
always passes PROT_EXEC to the mmap() call. While this doesn't matter
to most people whilst the code is running, it will cause a pointless
icache flush when starting every FDPIC application. Typically this
icache flush will be of a region on the order of 128KB in size, or may
be the entire icache, depending on the facilities available on the CPU.
In the case where the arch default behaviour seems to be desired
(EXSTACK_DEFAULT), we probe VM_STACK_FLAGS for VM_EXEC to determine
whether we should be setting PROT_EXEC or not.
For arches that support an MPU (Memory Protection Unit - an MMU without
the virtual mapping capability), setting PROT_EXEC or not will make an
important difference.
It should be noted that this change also affects the executability of
the brk region, since ELF-FDPIC has that share with the stack. However,
this is probably irrelevant as NOMMU programs aren't likely to use the
brk region, preferring instead allocation via mmap().
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make sure compiler won't do weird things with limits. E.g. fetching
them twice may return 2 different values after writable limits are
implemented.
I.e. either use rlimit helpers added in
3e10e716ab
or ACCESS_ONCE if not applicable.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
pcibus_to_node can return -1 if we cannot determine which node a pci bus
is on. If passed -1, cpumask_of_node will negatively index the lookup array
and pull in random data:
# cat /sys/devices/pci0000:00/0000:00:01.0/local_cpus
00000000,00000003,00000000,00000000
# cat /sys/devices/pci0000:00/0000:00:01.0/local_cpulist
64-65
Change cpumask_of_node to check for -1 and return cpu_all_mask in this
case:
# cat /sys/devices/pci0000:00/0000:00:01.0/local_cpus
ffffffff,ffffffff,ffffffff,ffffffff
# cat /sys/devices/pci0000:00/0000:00:01.0/local_cpulist
0-127
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
cleanup only.
setup_arch(), doesn't care care if ACPI initialization succeeded
or failed, so delete acpi_boot_table_init()'s return value.
Signed-off-by: Len Brown <len.brown@intel.com>
With the recent irq migration fixes (post 2.6.32), Gary Hade has noticed
"No IRQ handler for vector" messages during the 2.6.33-rc1 kernel boot on IBM
AMD platforms and root caused the issue to this commit:
> commit 23359a88e7
> Author: Suresh Siddha <suresh.b.siddha@intel.com>
> Date: Mon Oct 26 14:24:33 2009 -0800
>
> x86: Remove move_cleanup_count from irq_cfg
As part of this patch, we have removed the move_cleanup_count check
in smp_irq_move_cleanup_interrupt(). With this change, we can run into a
situation where an irq cleanup interrupt on a cpu can cleanup the vector
mappings associated with multiple irqs, of which one of the irq's migration
might be still in progress. As such when that irq hits the old cpu, we get
the "No IRQ handler" messages.
Fix this by checking for the irq_cfg's move_in_progress and if the move
is still in progress delay the vector cleanup to another irq cleanup
interrupt request (which will happen when the irq starts arriving at the
new cpu destination).
Reported-and-tested-by: Gary Hade <garyhade@us.ibm.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
LKML-Reference: <1262804191.2732.7.camel@sbs-t61.sc.intel.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
* 'davinci-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-davinci:
DaVinci: DM365: Add the device_enable for the DaVinci Keyscan
davinci: enable ARCH_HAS_HOLES_MEMORYMODEL for DaVinci
davinci: da8xx/omap-l1: mark RTC as a wakeup source
davinci: cp_intc: provide set_wake function
Davinci VPFE Capture: Take i2c adapter id through platform data
Adds the device_enable function to the DaVinci Keyscan platform data
to setup the PINMUX configuration.
It also removes #ifdef from the DM365 EVM board in order to load it
properly as a module.
Signed-off-by: Miguel Aguilar <miguel.aguilar@ridgerun.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
All DaVinci platforms include a DSP or co-processor for
audio/video acceleration.
While creating memory for the DSP/co-processor, system
integrator can end up creating a hole in the memory map
of the sort:
<kernel memory> <hole (memory for DSP)> <kernel memory>
This sort of configuration needs ARCH_HAS_HOLES_MEMORYMODEL
enabled. See further details see this discussion on ARM
linux mailing list:
http://www.mail-archive.com/linux-omap@vger.kernel.org/msg15262.html
The patch is boot tested on OMAP-L138, DM6446 and DM355 EVMs
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
CC: Sriramakrishnan <srk@ti.com>
CC: Khasim Syed Mohammed <khasim@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
On da850, RTC alarm is a wakeup source from deep sleep.
Mark it as a wakeup source after the rtc platform device
is registered.
Without this patch, the rtc-omap driver suspends the RTC
during the suspend sequence and hence it cannot wakeup the
SoC.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
There is nothing special to be done for interrupts
which can wakeup the device from sleep on CP-INTC,
but not having a set_wake implemented prevents use
of common drivers which expect this function to be
implemented for all wakeup interrupt sources.
This patch fixes the issue encountered when using the
omap-rtc driver on DA850. On DA850 the RTC alarm
interrupt is used to wake up the SoC from deep sleep
mode. Without this patch, the disable_irq_wake throws
an unbalanced wake disable warning while resuming
because the previous enable call fails for lack of
set_wake implementation.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The I2C adapter ID is actually depends on Board and may vary, Davinci
uses id=1, but in case of AM3517 id=3.
So modified respective davinci board files.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
* master.kernel.org:/home/rmk/linux-2.6-arm: (22 commits)
ARM: 5865/1: nuc900 ethernet driver needs mii
ARM: 5864/1: Implement arch_reset() in NUC900
ARM: 5863/1: fix bugs of clock source of NUC900
ARM: 5858/1: Remove unused vma_vm_flags macro from v7wbi_flush_user_tlb_range
imx/mx3: depend on USB_ULPI for otg_ulpi_create
ARM: MX3: make CPU revision number detection work on all boards
mx25: pdk: add platform code for FEC support
mx25: add support for FEC on i.MX25
mx25: s/NO_PAD_CTL/NO_PAD_CTRL/
mx31moboard: fix usbh device names
mx3: add support for the mt9v022 camera sensor to pcm037 platform
mx27: mxt_td60: Remove not used UART pins
[ARM] pxa/poodle: fix incorrect 'gpio_card_detect' of MMC
[ARM] pxa/zylonite: simplify reduntant gpio settings on mmc slot
[ARM] pxa/ttc_dkb: remove duplicate macro definition
[ARM] pxa/zeus: provide power-source information when APM is enabled
[ARM] pxa/zeus: relax memory timings on Zeus ethernet ports
[ARM] pxa/zeus: make internal zeus_get_pcb_info static
[ARM] pxa/littleton: select CPU_PXA300 and CPU_PXA310
[ARM] pxa/littleton: add UART3 GPIO config
...
Add a function pointer in the platform data of the DaVinci Keyscan driver
called device_enable, in order to perform board specific actions when
the device is initialized, like setup the PINMUX configuration.
Signed-off-by: Miguel Aguilar <miguel.aguilar@ridgerun.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
sparc64: Fix Niagara2 perf event handling.
sparc64: Fix NMI programming when perf events are active.
bbc_envctrl: Clean up properly if kthread_run() fails.
This reverts commit ae1b22f6e4.
As Linus said in 982d007a6e: "There was something really messy about
cmpxchg8b and clone CPU's, so if you enable it on other CPUs later, do it
carefully."
This breaks lguest for those configs, but we can fix that by emulating
if we have to.
Fixes: http://bugzilla.kernel.org/show_bug.cgi?id=14884
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Callers of copy_from_user() expect it to return the number of bytes
it could not copy. In no case it is supposed to return -EFAULT.
In case of a detected buffer overflow just return the requested
length. In addition one could think of a memset that would clear
the size of the target object.
[ hpa: code is not in .32 so not needed for -stable ]
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Acked-by: Arjan van de Ven <arjan@linux.intel.com>
LKML-Reference: <20100105131911.GC5480@osiris.boeblingen.de.ibm.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Implement arch_reset(), reboot from shell become possible.
Signed-off-by: lijie <eltshanli@gmail.com>
Acked-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch fix following bugs:
1. typo error, CLOCK_EVT_MODE_PERIODIC -> CLOCK_EVT_FEAT_PERIODIC
2. TCSR register of timer1 missed PRESCALE
3. timer1 should be enabled before register it to clock source.
Signed-off-by: lijie <eltshanli@gmail.com>
Acked-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
For chips like Niagara2 that have true overflow indications
in the %pcr (which we don't actually need and don't use)
the interrupt signal persists until the overflow bits are
cleared by an explicit %pcr write.
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit ae1b22f6e4.
As Linus said in 982d007a6e: "There was something really messy about
cmpxchg8b and clone CPU's, so if you enable it on other CPUs later, do it
carefully."
This breaks lguest for those configs, but we can fix that by emulating
if we have to.
Fixes: http://bugzilla.kernel.org/show_bug.cgi?id=14884
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
LKML-Reference: <201001051248.49700.rusty@rustcorp.com.au>
Cc: stable@kernel.org
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
If perf events are active, we should not reset the %pcr to
PCR_PIC_PRIV. That perf events code does the management.
Signed-off-by: David S. Miller <davem@davemloft.net>
It is above 0x100 (PCI-Express extended register space), so if mmconf
is not enable, we can't access it.
[ hpa: changed the bound from 0x200 to 0x120, which is the tight
bound. ]
Reported-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <1261525263-13763-3-git-send-email-yinghai@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
fix for error that is introduced by
| x86: Use find_e820() instead of hard coded trampoline address
it should end with PAGE_SIZE + PAGE_SIZE
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <1261525263-13763-2-git-send-email-yinghai@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6:
[S390] Update default configuration.
[S390] Have param.h simply include <asm-generic/param.h>.
[S390] qdio: convert global statistics to per-device stats
otg_ulpi_create is defined in drivers/usb/otg/ulpi.c which depends on
CONFIG_USB_ULPI. So protect its usage by the same symbol. Moreover
mxc_ulpi_access_ops needs CONFIG_MXC_ULPI.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Valentin Longchamp <valentin.longchamp@epfl.ch>
Cc: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Commit 52939c03 (ARM: MX3: fix CPU revision number detection) started
using the CPU's SREV register for revision number detection. This
makes it mandatory to have a valid SPBA0 mapping. Add this to the
global map_io code instead of adding multiple copies for each board.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Daniel Mack <daniel@caiaq.de>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Tested on Qong (EVB-Lite)
Tested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Since the files have identical content, might as well simplify.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This has the adverse effect of converting many 29bit configs to 32bit
mode, while this is a change that needs to be done manually for each
platform. Turn it off by default in order to cut down on spurious bug
reports.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
While the PMB is available on SH-4A parts, SH4AL-DSP parts exclude it
altogether. As such, explicitly disable PMB support for these parts. If
this changes in the future for newer subtypes, this will have to be made
more fine-grained.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Check whether L2 is present or not in XSC3. If it's present, enable L2
immediately.
Disabling L2 after L2 is enabled that would result in unpredicatable behavior
of XSC3 processor.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Outer cache checked whether L2 is enabled or not. If L2 isn't enabled in XSC3,
it would enable L2. This operation is evil that would make system hang.
In XSC3 core document, these words are mentioned in below.
"Following reset, the L2 Unified Cache Enable bit is cleared. To enable the L2
Cache, software may set the bit to a '1' before or at the same time as enabling
the MMU. Enabling the L2 Cache after the MMU has been enabled or disabling the
L2 Cache after the L2 Cache has been enabled, may result in unpredictable
behavior of the processor."
When outer cache is initialized, the MMU is already enabled. We couldn't enable
L2 after MMU enabled.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86/agp: Fix agp_amd64_init() initialization with CONFIG_GART_IOMMU enabled
x86: SGI UV: Fix writes to led registers on remote uv hubs
x86, kmemcheck: Use KERN_WARNING for error reporting
x86: Use KERN_DEFAULT log-level in __show_regs()
x86, compress: Force i386 instructions for the decompressor
x86/amd-iommu: Fix initialization failure panic
dma-debug: Do not add notifier when dma debugging is disabled.
x86: Fix objdump version check in chkobjdump.awk for different formats.
Trivial conflicts in arch/x86/include/asm/uv/uv_hub.h due to me having
applied an earlier version of an SGI UV fix.
Pass the frame pointer from the regs of the interrupted path
to dump_trace() while processing the stack trace.
Currently, dump_trace() takes the current bp and starts the
callchain from dump_trace() itself. This is wasteful because
we need to walk through the entire NMI/DEBUG stack before
retrieving the interrupted point.
We can fix that by just using the frame pointer from the
captured regs. It points exactly where we want to start.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Paul Mackerras <paulus@samba.org>
LKML-Reference: <1262235183-5320-1-git-send-regression-fweisbec@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Paul Mackerras <paulus@samba.org>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
ACPI: introduce kernel parameter acpi_sleep=sci_force_enable
ACPI: WMI: Survive BIOS with duplicate GUIDs
dell-wmi - fix condition to abort driver loading
wmi: check find_guid() return value to prevent oops
dell-wmi, hp-wmi, msi-wmi: check wmi_get_event_data() return value
ACPI: hp-wmi, msi-wmi: clarify that wmi_install_notify_handler() returns an acpi_status
dell-wmi: sys_init_module: 'dell_wmi'->init suspiciously returned 21, it should
ACPI video: correct error-handling code
ACPI video: no warning message if "acpi_backlight=vendor" is used
ACPI: fix ACPI=n allmodconfig build
thinkpad-acpi: improve Kconfig help text
thinkpad-acpi: update volume subdriver documentation
thinkpad-acpi: make volume subdriver optional
thinkpad-acpi: don't fail to load the entire module due to ALSA problems
thinkpad-acpi: don't take the first ALSA slot by default
Introduce kernel parameter acpi_sleep=sci_force_enable
some laptop requires SCI_EN being set directly on resume,
or else they hung somewhere in the resume code path.
We already have a blacklist for these laptops but we still need
this option, especially when debugging some suspend/resume problems,
in case there are systems that need this workaround and are not yet
in the blacklist.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
mkuboot.sh provides a basic wrapper for the 'mkimage' utility. Using
mkuboot.sh provides clearer error reporting and allows a toolchain to
use its own 'mkimage' executable specified by ${CROSS_COMPILE}mkimage.
Additionally, this brings PowerPC in line with other architectures
which already call mkimage via mkuboot.sh.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI/cardbus: Add a fixup hook and fix powerpc
PCI: change PCI nomenclature in drivers/pci/ (non-comment changes)
PCI: change PCI nomenclature in drivers/pci/ (comment changes)
PCI: fix section mismatch on update_res()
PCI: add Intel 82599 Virtual Function specific reset method
PCI: add Intel USB specific reset method
PCI: support device-specific reset methods
PCI: Handle case when no pci device can provide cache line size hint
PCI/PM: Propagate wake-up enable for PCIe devices too
vgaarbiter: fix a typo in the vgaarbiter Documentation
* 'kvm-updates/2.6.33' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: get rid of kvm_create_vm() unused label warning on s390
KVM: powerpc: Fix mtsrin in book3s_64 mmu
KVM: ia64: fix build breakage due to host spinlock change
KVM: x86: Extend KVM_SET_VCPU_EVENTS with selective updates
KVM: LAPIC: make sure IRR bitmap is scanned after vm load
KVM: Fix possible circular locking in kvm_vm_ioctl_assign_device()
KVM: MMU: remove prefault from invlpg handler
The wrong address was being used to write the SCIR led regs on remote
hubs. Also, there was an inconsistency between how BIOS and the kernel
indexed these regs. Standardize on using the lower 6 bits of the APIC
ID as the index.
This patch fixes the problem of writing to an errant address to a
cpu # >= 64.
Signed-off-by: Mike Travis <travis@sgi.com>
Reviewed-by: Jack Steiner <steiner@sgi.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
PXA mmc host driver supports card detect, read only and power gpio pin
setting already. Zylonite platform driver needn't implement this any more.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
ARRAY_AND_SIZE is already defined arch/arm/mach-mmp/common.h which is
already included.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Bin Yang <bin.yang@marvell.com>
Acked-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
DM9000s on Zeus sometime fail under heavy load.
Relaxing the timings a bit seems to be of a great help.
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This has to be selected, otherwise some peripherals don't get initialized.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Use resource_size for {request/release}_mem_region and ioremap.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
The wrong address was being used to write the SCIR led regs on
remote hubs. Also, there was an inconsistency between how BIOS
and the kernel indexed these regs. Standardize on using the
lower 6 bits of the APIC ID as the index.
This patch fixes the problem of writing to an errant address to
a cpu # >= 64.
Signed-off-by: Mike Travis <travis@sgi.com>
Reviewed-by: Jack Steiner <steiner@sgi.com>
Cc: Robin Holt <holt@sgi.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: stable@kernel.org
LKML-Reference: <4B3922F9.3060905@sgi.com>
[ v2: fix a number of annoying checkpatch artifacts and whitespace noise ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
As CPUs are migrated over to more fully-featured clock frameworks of
their own and off of the legacy CPG code, they no longer have any real
need for defining the PCLK value. The PCLK define in itself is already
fairly misleading, as many boards get their input clocks from different
sources, making this value fairly arbitrary anyways.
Outside of the legacy CPG clock framework, the only place where this
value is used is for deriving CLOCK_TICK_RATE, which we set back to the
legacy PIT value that it was before the PCLK definitions were added in
the first place.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
As suggested by Vegard Nossum, use KERN_WARNING for error
reporting to make sure kmemcheck reports end up in syslog.
Suggested-by: Vegard Nossum <vegard.nossum@gmail.com>
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Andrew Morton <akpm@linux-foundation.org>
LKML-Reference: <1261990935.4641.7.camel@penberg-laptop>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Andrew Morton reported a strange looking kmemcheck warning:
WARNING: kmemcheck: Caught 32-bit read from uninitialized memory (ffff88004fba6c20)
0000000000000000310000000000000000000000000000002413000000c9ffff
u u u u u u u u u u u u u u u u i i i i i i i i u u u u u u u u
[<ffffffff810af3aa>] kmemleak_scan+0x25a/0x540
[<ffffffff810afbcb>] kmemleak_scan_thread+0x5b/0xe0
[<ffffffff8104d0fe>] kthread+0x9e/0xb0
[<ffffffff81003074>] kernel_thread_helper+0x4/0x10
[<ffffffffffffffff>] 0xffffffffffffffff
The above printout is missing register dump completely. The
problem here is that the output comes from syslog which doesn't
show KERN_INFO log-level messages. We didn't see this before
because both of us were testing on 32-bit kernels which use the
_default_ log-level.
Fix that up by explicitly using KERN_DEFAULT log-level for
__show_regs() printks.
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Vegard Nossum <vegard.nossum@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
LKML-Reference: <1261988819.4641.2.camel@penberg-laptop>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
We were shifting the Ks/Kp/N bits one bit too far on mtsrin. It took
me some time to figure that out, so I also put in some debugging and a
comment explaining the conversion.
This fixes current OpenBIOS boot on PPC64 KVM.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
Len Brown pointed out that allmodconfig is broken for
ia64 because of:
arch/ia64/kvm/vmm.c: In function 'vmm_spin_unlock':
arch/ia64/kvm/vmm.c:70: error: 'spinlock_t' has no member named 'raw_lock'
KVM has it's own spinlock routines. It should not depend on the base kernel
spinlock_t type (which changed when ia64 switched to ticket locks). Define
its own vmm_spinlock_t type.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
User space may not want to overwrite asynchronously changing VCPU event
states on write-back. So allow to skip nmi.pending and sipi_vector by
setting corresponding bits in the flags field of kvm_vcpu_events.
[avi: advertise the bits in KVM_GET_VCPU_EVENTS]
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
The vcpus are initialized with irr_pending set to false, but
loading the LAPIC registers with pending IRR fails to reset
the irr_pending variable.
Cc: stable@kernel.org
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
The invlpg prefault optimization breaks Windows 2008 R2 occasionally.
The visible effect is that the invlpg handler instantiates a pte which
is, microseconds later, written with a different gfn by another vcpu.
The OS could have other mechanisms to prevent a present translation from
being used, which the hypervisor is unaware of.
While the documentation states that the cpu is at liberty to prefetch tlb
entries, it looks like this is not heeded, so remove tlb prefetch from
invlpg.
Cc: stable@kernel.org
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Recently, some distros have started shipping versions of gcc which
default to -march=i686. This breaks building kernels for pre-i686
machines, even if they have been selected in Kconfig, due to the
generation of CMOV instructions.
There isn't enough benefit to try to preserve the generation of these
instructions even when selected, so simply force -march=i386 for the
decompressor when building a 32-bit kernel.
Reported-and-tested-by: Chris Rankin <rankincj@yahoo.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
LKML-Reference: <219280.97558.qm@web52907.mail.re2.yahoo.com>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (34 commits)
classmate-laptop: add support for Classmate PC ACPI devices
hp-wmi: Fix two memleaks
acer-wmi, msi-wmi: Remove needless DMI MODULE_ALIAS
dell-wmi: do not keep driver loaded on unsupported boxes
wmi: Free the allocated acpi objects through wmi_get_event_data
drivers/platform/x86/acerhdf.c: check BIOS information whether it begins with string of table
acerhdf: add new BIOS versions
acerhdf: limit modalias matching to supported
toshiba_acpi: convert to seq_file
asus_acpi: convert to seq_file
ACPI: do not select ACPI_DOCK from ATA_ACPI
sony-laptop: enumerate rfkill devices using SN06
sony-laptop: rfkill support for newer models
ACPI: fix OSC regression that caused aer and pciehp not to load
MAINTAINERS: add maintainer for msi-wmi driver
fujitu-laptop: fix tests of acpi_evaluate_integer() return value
arch/x86/kernel/cpu/cpufreq/acpi-cpufreq.c: avoid cross-CPU interrupts by using smp_call_function_any()
ACPI: processor: remove _PDC object list from struct acpi_processor
ACPI: processor: change acpi_processor_set_pdc() interface
ACPI: processor: open code acpi_processor_cleanup_pdc
...
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm:
VIDEO: cyberpro: pci_request_regions needs a persistent name
ARM: dma-isa: request cascade channel after registering it
ARM: footbridge: trim down old ISA rtc setup
ARM: fix PAGE_KERNEL
ARM: Fix wrong shared bit for CPU write buffer bug test
ARM: 5857/1: ARM: dmabounce: fix build
ARM: 5856/1: Fix bug of uart0 platfrom data for nuc900
ARM: 5855/1: putc support for nuc900
ARM: 5854/1: fix compiling error for NUC900
ARM: 5849/1: ARMv7: fix Oprofile events count
ARM: add missing include to nwflash.c
ARM: Kill CONFIG_CPU_32
ARM: Convert VFP/Crunch/XscaleCP thread_release() to exit_thread()
ARM: 5853/1: ARM: Fix build break on ARM v6 and v7
This fixes a "start_kernel(): bug: interrupts were enabled early".
rtc_cmos now takes care of initializing the ISA RTC and reading the
current time and date from it; there's no need to repeat that here,
thereby causing interrupts to be enabled too early.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
PAGE_KERNEL should not be executable; any area marked executable can
be prefetched into the instruction cache. We don't want vmalloc areas
to be read in this way.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
With some of the cache rework an address aliasing optimization was added,
but this managed to fail on certain mappings resulting in pages with
PG_dcache_dirty set never writing back their dcache lines. This patch
reverts to the earlier behaviour of simply always writing back when the
dirty bit is set.
Signed-off-by: Markus Pietrek <Markus.Pietrek@emtrion.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
o remove unused define
o add device name comment
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This reverts commit 9f15226e75. It's just
wrong, and broke resume for Rafael even on a non-AMD CPU.
As Rafael says:
"... it causes microcode_init_cpu() to be called during resume even for
CPUs for which there's no microcode to apply. That, in turn, results
in executing request_firmware() (on Intel CPUs at least) which doesn't
work at this stage of resume (we have device interrupts disabled, I/O
devices are still suspended and so on).
If I'm not mistaken, the "if (uci->valid)" logic means "if that CPU is
known to us" , so before commit 9f15226e75 microcode_resume_cpu() was
called for all CPUs already in the system during suspend, which was
the right thing to do. The commit changed it so that the CPUs without
microcode to apply are now treated as "unknown", which is not quite
right.
The problem this commit attempted to solve has to be handled
differently."
Bisected-and -requested-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix two bugs in s3c_nand_set_platdata() where thet device's platform
data was not set, and the wrong error check was being performed on
the return of s3c_nand_copy_set().
Fixes the following OOPS:
Unable to handle kernel NULL pointer dereference at virtual address 00000004
PC is at s3c24xx_nand_probe+0x234/0x594
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
It is unpredictable to have the same memory mapped using different
shared bit settings for ARMv6 and ARMv7 CPUs. Fix this for the CPU
write buffer bug test.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add definition for the touchscreen driver platform data and initial
support for the H1940 machine.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add the NAND_SCAN_SILENT_NODEV to the optional NAND devices that may not
be fitted to the board
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Simtec Linux Team <linux@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add the NAND_SCAN_SILENT_NODEV to the optional NAND devices that may not
be fitted to the board
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Simtec Linux Team <linux@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (36 commits)
powerpc/gc/wii: Remove get_irq_desc()
powerpc/gc/wii: hlwd-pic: convert irq_desc.lock to raw_spinlock
powerpc/gamecube/wii: Fix off-by-one error in ugecon/usbgecko_udbg
powerpc/mpic: Fix problem that affinity is not updated
powerpc/mm: Fix stupid bug in subpge protection handling
powerpc/iseries: use DECLARE_COMPLETION_ONSTACK for non-constant completion
powerpc: Fix MSI support on U4 bridge PCIe slot
powerpc: Handle VSX alignment faults correctly in little-endian mode
powerpc/mm: Fix typo of cpumask_clear_cpu()
powerpc/mm: Fix hash_utils_64.c compile errors with DEBUG enabled.
powerpc: Convert BUG() to use unreachable()
powerpc/pseries: Make declarations of cpu_hotplug_driver_lock() ANSI compatible.
powerpc/pseries: Don't panic when H_PROD fails during cpu-online.
powerpc/mm: Fix a WARN_ON() with CONFIG_DEBUG_PAGEALLOC and CONFIG_DEBUG_VM
powerpc/defconfigs: Set HZ=100 on pseries and ppc64 defconfigs
powerpc/defconfigs: Disable token ring in powerpc defconfigs
powerpc/defconfigs: Reduce 64bit vmlinux by making acenic and cramfs modules
powerpc/pseries: Select XICS and PCI_MSI PSERIES
powerpc/85xx: Wrong variable returned on error
powerpc/iseries: Convert to proc_fops
...
Presently acpi-cpufreq will perform the MSR read on the first CPU in the
mask. That's inefficient if that CPU differs from the current CPU.
Because we have to perform a cross-CPU call, but we could have run the
rdmsr on the current CPU.
So switch to using the new smp_call_function_any(), which will perform the
call on the current CPU if that CPU is present in the mask (it is).
Cc: "Zhang, Yanmin" <yanmin_zhang@linux.intel.com>
Cc: Dave Jones <davej@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Jaswinder Singh Rajput <jaswinder@kernel.org>
Cc: Len Brown <len.brown@intel.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Commit f74f7e57ae (ARM: use
flush_kernel_dcache_area() for dmabounce) has broken dmabounce build:
CC arch/arm/common/dmabounce.o
arch/arm/common/dmabounce.c: In function 'unmap_single':
arch/arm/common/dmabounce.c:315: error: implicit declaration of function '__cpuc_flush_kernel_dcache_area'
make[2]: *** [arch/arm/common/dmabounce.o] Error 1
Fix it.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix bug of uart0 platfrom data for nuc900
Signed-off-by: lijie <eltshanli@gmail.com>
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
putc support for nuc900
Signed-off-by: lijie <eltshanli@gmail.com>
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
fix compiling error for NUC900
Signed-off-by: lijie <eltshanli@gmail.com>
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On Oprofile ARMv7 the PMNC_D bit was set to lower the PMU IRQs
and so to decrease the risk of errata #628216 from appearing.
The effect of setting the PMNC_D bit is that the CCNT counter
is divided by 64, making the program counter events count
inaccurate.
The new OMAP3 r4 cores should have that errata fixed.
The PMNC_D bit should not be set, this patch fixes it.
Signed-off-by: Jean Pihet <jpihet@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The x86 and ia64 implementations of the function in $subject are
exactly the same.
Also, since the arch-specific implementations of setting _PDC have
been completely hollowed out, remove the empty shells.
Cc: Tony Luck <tony.luck@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The only thing arch-specific about calling _PDC is what bits get
set in the input obj_list buffer.
There's no need for several levels of indirection to twiddle those
bits. Additionally, since we're just messing around with a buffer,
we can simplify the interface; no need to pass around the entire
struct acpi_processor * just to get at the buffer.
Cc: Tony Luck <tony.luck@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Both x86 and ia64 initialize _PDC with mostly common bit settings.
Factor out the common settings and leave the arch-specific ones alone.
Cc: Tony Luck <tony.luck@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The x86 and ia64 implementations of arch_acpi_processor_init_pdc()
are almost exactly the same. The only difference is in what bits
they set in obj_list buffer.
Combine the boilerplate memory management code, and leave the
arch-specific bit twiddling in separate implementations.
Cc: Tony Luck <tony.luck@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
arch dependent helper function that tells us if we should attempt to
evaluate _PDC on this machine or not.
The x86 implementation assumes that the CPUs in the machine must be
homogeneous, and that you cannot mix CPUs of different vendors.
Cc: Tony Luck <tony.luck@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The assumption that acpi_table_parse passes the return value
of the hanlder function to the caller proved wrong
recently. The return value of the handler function is
totally ignored. This makes the initialization code for AMD
IOMMU buggy in a way that could cause a kernel panic on
initialization. This patch fixes the issue in the AMD IOMMU
driver.
Cc: stable@kernel.org
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
We don't actually require this in the cpu_relax() polling case, so just
cuddle these around the sleeping version.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Fix the following build failures:
arch/powerpc/platforms/embedded6xx/flipper-pic.c: In function 'flipper_pic_map':
arch/powerpc/platforms/embedded6xx/flipper-pic.c:105: error: implicit declaration of function 'get_irq_desc'
arch/powerpc/platforms/embedded6xx/hlwd-pic.c: In function 'hlwd_pic_map':
arch/powerpc/platforms/embedded6xx/hlwd-pic.c:98: error: implicit declaration of function 'get_irq_desc'
These failures are caused by the changes introduced in commit
"powerpc: Remove get_irq_desc()". The reason these drivers were not
updated is that they weren't merged yet.
Signed-off-by: Albert Herranz <albert_herranz@yahoo.es>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Fix the following build failures:
arch/powerpc/platforms/embedded6xx/hlwd-pic.c: In function 'hlwd_pic_irq_cascade':
arch/powerpc/platforms/embedded6xx/hlwd-pic.c:135: error: passing argument 1 of 'spin_lock' from incompatible pointer type
arch/powerpc/platforms/embedded6xx/hlwd-pic.c:137: error: passing argument 1 of 'spin_unlock' from incompatible pointer type
arch/powerpc/platforms/embedded6xx/hlwd-pic.c:145: error: passing argument 1 of 'spin_lock' from incompatible pointer type
arch/powerpc/platforms/embedded6xx/hlwd-pic.c:149: error: passing argument 1 of 'spin_unlock' from incompatible pointer type
These failures are caused by the changes introduced in commit
"genirq: Convert irq_desc.lock to raw_spinlock". The reason this driver
was not updated is that it wasn't merged yet.
Signed-off-by: Albert Herranz <albert_herranz@yahoo.es>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mattst88/alpha-2.6:
alpha: Convert BUG() to use unreachable()
alpha: Add minimal support for software performance events
alpha: Wire up missing/new syscalls
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf session: Make events_stats u64 to avoid overflow on 32-bit arches
hw-breakpoints: Fix hardware breakpoints -> perf events dependency
perf events: Dont report side-band events on each cpu for per-task-per-cpu events
perf events, x86/stacktrace: Fix performance/softlockup by providing a special frame pointer-only stack walker
perf events, x86/stacktrace: Make stack walking optional
perf events: Remove unused perf_counter.h header file
perf probe: Check new event name
kprobe-tracer: Check new event/group name
perf probe: Check whether debugfs path is correct
perf probe: Fix libdwarf include path for Debian
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, irq: Allow 0xff for /proc/irq/[n]/smp_affinity on an 8-cpu system
Makefile: Unexport LC_ALL instead of clearing it
x86: Fix objdump version check in arch/x86/tools/chkobjdump.awk
x86: Reenable TSC sync check at boot, even with NONSTOP_TSC
x86: Don't use POSIX character classes in gen-insn-attr-x86.awk
Makefile: set LC_CTYPE, LC_COLLATE, LC_NUMERIC to C
x86: Increase MAX_EARLY_RES; insufficient on 32-bit NUMA
x86: Fix checking of SRAT when node 0 ram is not from 0
x86, cpuid: Add "volatile" to asm in native_cpuid()
x86, msr: msrs_alloc/free for CONFIG_SMP=n
x86, amd: Get multi-node CPU info from NodeId MSR instead of PCI config space
x86: Add IA32_TSC_AUX MSR and use it
x86, msr/cpuid: Register enough minors for the MSR and CPUID drivers
initramfs: add missing decompressor error check
bzip2: Add missing checks for malloc returning NULL
bzip2/lzma/gzip: pre-boot malloc doesn't return NULL on failure
Different version of objdump says its version in different way;
GNU objdump 2.16.1
or
GNU objdump version 2.19.51.0.14-1.fc11 20090722
This patch uses the first argument which starts with a number
as version string.
Changes in v2:
- Remove unneeded increment.
Signed-off-by: Masami Hiramatsu <mhiramat@redhat.com>
LKML-Reference: <20091218154012.16960.5113.stgit@dhcp-100-2-132.bos.redhat.com>
Suggested-by: H. Peter Anvin <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Nobody except ptrace itself should use task->ptrace or PT_PTRACED
directly, change arch/s390/kernel/traps.c to use the helper.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The elf notes number for the upper register halves is s390 specific.
Change the name of the elf notes to include S390.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
26-bit ARM support was removed a long time ago, and this symbol has
been defined to be 'y' ever since. As it's never disabled anymore,
we can kill it without any side effects.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This avoids races in the VFP code where the dead thread may have
state on another CPU. By moving this code to exit_thread(), we
will be running as the thread, and therefore be running on the
current CPU.
This means that we can ensure that the only local state is accessed
in the thread notifiers.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The kbuild's select command doesn't propagate through the config
dependencies.
Hence the current rules of hardware breakpoint's config can't
ensure perf can never be disabled under us.
We have:
config X86
selects HAVE_HW_BREAKPOINTS
config HAVE_HW_BREAKPOINTS
select PERF_EVENTS
config PERF_EVENTS
[...]
x86 will select the breakpoints but that won't propagate to perf
events. The user can still disable the latter, but it is
necessary for the breakpoints.
What we need is:
- x86 selects HAVE_HW_BREAKPOINTS and PERF_EVENTS
- HAVE_HW_BREAKPOINTS depends on PERF_EVENTS
so that we ensure PERF_EVENTS is enabled and frozen for x86.
This fixes the following kind of build errors:
In file included from arch/x86/kernel/hw_breakpoint.c:31:
include/linux/hw_breakpoint.h: In function 'hw_breakpoint_addr':
include/linux/hw_breakpoint.h:39: error: 'struct perf_event' has no member named 'attr'
v2: Select also ANON_INODES from x86, required for perf
Reported-by: Cyrill Gorcunov <gorcunov@gmail.com>
Reported-by: Michal Marek <mmarek@suse.cz>
Reported-by: Andrew Randrianasulu <randrik_a@yahoo.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Cc: K.Prasad <prasad@linux.vnet.ibm.com>
LKML-Reference: <1261010034-7786-1-git-send-regression-fweisbec@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Commit 2c9b9c849 added an argument to __cpuc_flush_dcache_page
and renamed it.
Update a caller of the old function to fix this build error:
CC arch/arm/mm/copypage-v6.o
arch/arm/mm/copypage-v6.c: In function 'v6_copy_user_highpage_nonaliasing':
arch/arm/mm/copypage-v6.c:51: error: implicit declaration of function '__cpuc_flush_dcache_page'
make[1]: *** [arch/arm/mm/copypage-v6.o] Error 1
make: *** [arch/arm/mm] Error 2
Reported-by: Jinsung Yang <jsgood.yang@samsung.com>
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Use the new unreachable() macro instead of for(;;);
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
CC: Richard Henderson <rth@twiddle.net>
CC: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
CC: linux-alpha@vger.kernel.org
Signed-off-by: Matt Turner <mattst88@gmail.com>
In the kernel the patch enables configuration of the perf event
option, adds the perf_event_open syscall, and includes a minimal
architecture specific asm/perf_event.h header file.
Signed-off-by: Michael Cree <mcree@orcon.net.nz>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Matt Turner <mattst88@gmail.com>
This wire up the: fallocate, timerfd_create, timerfd_settime,
timerfd_gettime, signalfd4, eventfd2, epoll_create1, dup3, pipe2,
inotify_init1, preadv, pwritev and rt_tgsigqueueinfo syscalls for
the alpha port.
For umount2, alpha have an "old" and "new" version called: oldumount and
umount; so ignore umount2.
Rebased on top of 6e17e8b9fb by Matt
Turner.
Signed-off-by: Daniele Calore <orkaan@orkaan.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: Matt Turner <mattst88@gmail.com>
John Blackwood reported:
> on an older Dell PowerEdge 6650 system with 8 cpus (4 are hyper-threaded),
> and 32 bit (x86) kernel, once you change the irq smp_affinity of an irq
> to be less than all cpus in the system, you can never change really the
> irq smp_affinity back to be all cpus in the system (0xff) again,
> even though no error status is returned on the "/bin/echo ff >
> /proc/irq/[n]/smp_affinity" operation.
>
> This is due to that fact that BAD_APICID has the same value as
> all cpus (0xff) on 32bit kernels, and thus the value returned from
> set_desc_affinity() via the cpu_mask_to_apicid_and() function is treated
> as a failure in set_ioapic_affinity_irq_desc(), and no affinity changes
> are made.
set_desc_affinity() is already checking if the incoming cpu mask
intersects with the cpu online mask or not. So there is no need
for the apic op cpu_mask_to_apicid_and() to check again
and return BAD_APICID.
Remove the BAD_APICID return value from cpu_mask_to_apicid_and()
and also fix set_desc_affinity() to return -1 instead of using BAD_APICID
to represent error conditions (as cpu_mask_to_apicid_and() can return
logical or physical apicid values and BAD_APICID is really to represent
bad physical apic id).
Reported-by: John Blackwood <john.blackwood@ccur.com>
Root-caused-by: John Blackwood <john.blackwood@ccur.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
LKML-Reference: <1261103386.2535.409.camel@sbs-t61>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The retry logic in ug_putc() is broken.
If the TX fifo is not ready and the counter runs out it will have a
value of -1 and no transfer should be attempted. Also, a counter
with a value of 0 means that the TX fifo got ready in the last try
and the transfer should be attempted.
Reported-by: "Juha Leppanen" <juha_motorsportcom@luukku.com>
Signed-off-by: "Juha Leppanen" <juha_motorsportcom@luukku.com>
Signed-off-by: Albert Herranz <albert_herranz@yahoo.es>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Since commit 57b150cce8, desc->affinity
of an irq is changed after calling desc->chip->set_affinity.
Therefore we need to fix the irq_choose_cpu() not to depend on the
desc->affinity for new mask.
Signed-off-by: Jiajun Wu <b06378@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit d28513bc7f ("Fix bug in pagetable
cache cleanup with CONFIG_PPC_SUBPAGE_PROT"), itself a fix for
breakage caused by an earlier clean up patch of mine, contains a
stupid bug. I changed the parameters of the subpage_protection()
function, but failed to update one of the callers.
This patch fixes it, and replaces a void * with a typed pointer so
that the compiler will warn on such an error in future.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The _ONSTACK variant should be used for on-stack completion,
otherwise it will break lockdep.
Signed-off-by: Yong Zhang <yong.zhang0@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: linuxppc-dev@ozlabs.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On machines using the Apple U4 bridge (AKA IBM CPC945) PCIe interface such
as the latest generation G5 machines x16 slot or the x16 slot of the
PowerStation, MSIs are currently broken (and will oops when enabling).
This fixes the oops and implements proper support for those. Instead of
using the PCIe <-> HT bridge conversion, on such slots we need to use
a bunch of magic registers in the bridge as the MSI target, encoding
the interrupt number in the low bits of the address itself
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch fixes the handling of VSX alignment faults in little-endian
mode (the current code assumes the processor is in big-endian mode).
The patch also makes the handlers clear the top 8 bytes of the register
when handling an 8 byte VSX load.
This is based on 2.6.32.
Signed-off-by: Neil Campbell <neilc@linux.vnet.ibm.com>
Cc: <stable@kernel.org>
Acked-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The function name of cpumask_clear_cpu was not correct. Fortunately
nobody uses that code with hotplug yet :-)
Reported-by: Jin Qing <b24347@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This time without the funny characters.
Fix following build errors generated with DEBUG=1
cc1: warnings being treated as errors
arch/powerpc/mm/hash_utils_64.c: In function 'htab_dt_scan_page_sizes':
arch/powerpc/mm/hash_utils_64.c:343: error: format '%04x' expects type 'unsigned int', but argument 4 has type 'long unsigned int'
arch/powerpc/mm/hash_utils_64.c:343: error: format '%08x' expects type 'unsigned int', but argument 5 has type 'long unsigned int'
arch/powerpc/mm/hash_utils_64.c: In function 'htab_initialize':
arch/powerpc/mm/hash_utils_64.c:666: error: format '%x' expects type 'unsigned int', but argument 4 has type 'long unsigned int'
... SNIP ...
Signed-off-by: Sachin Sant <sachinp@in.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Use the new unreachable() macro instead of for(;;);
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: Paul Mackerras <paulus@samba.org>
CC: linuxppc-dev@ozlabs.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
And add the __acquires() and __releases() annotations, while at it.
Signed-off-by: Gautham R Shenoy <ego@in.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If an online-attempt on a CPU which has been offlined using H_CEDE
with an appropriate cede latency hint fails, don't panic.
Instead print the error message and let the __cpu_up() code notify the
CPU Hotplug framework of the failure, which in turn can notify the
other subsystem through CPU_UP_CANCELED.
Signed-off-by: Gautham R Shenoy <ego@in.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Set need to call __set_pte_at() and not set_pte_at() from __change_page_attr()
since the later will perform checks with CONFIG_DEBUG_VM that aren't suitable
to the way we override an existing PTE. (More specifically, it doesn't let
you write over a present PTE).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Now we have high res timers there is less of a reason for a high HZ value.
Furthermore I think there a few reasons we should reduce HZ to 100:
- Timer interrupt overhead. While this overhead is small, there are
applications that are very sensitive to jitter (eg some HPC apps).
- Issues with the timer wheel code. When coming out of NO_HZ idle we work our
way through the timer code one tick at a time. If we have been idle a long
time, this adds up - I sometimes see milliseconds of time spent in that
loop.
Long term we should fix the timer wheel algorithm, but for now if we reduce
HZ then we reduce the amount of work the timer code has to do when coming
out of idle.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Token what? Lets save some space in our powerpc kernels and remove token
ring support.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Machines with acenic adapters are rare these days, so we may as well make it
a module. Cramfs is also very rarely used so we can make it a module.
Together this saves 143kB on a 64bit compile:
text data bss dec hex filename
8247176 1729404 1221988 11198568 aae068 vmlinux~
8134997 1727588 1188836 11051421 a8a19d vmlinux
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
It's possible to set CONFIG_XICS without CONFIG_PCI_MSI. When that happens,
the kernel fails to build with
arch/powerpc/platforms/built-in.o: In function `.xics_startup':
xics.c:(.text+0x12f60): undefined reference to `.unmask_msi_irq' make: ***
[.tmp_vmlinux1] Error 1
Furthermore, as noted by Benjamin Herrenschmidt, "CONFIG_XICS should be
made invisible and selected by PSERIES."
This patch fixes PSERIES to select both options
Signed-off-by: Mel Gorman <mel[at]csn.ul.ie>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The wrong variable was returned in the case of an error.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The Collaborative Memory Manager (CMM) module allocates individual pages
over time that are not migratable. On a long running system this can
severely impact the ability to find enough pages to support a hotplug
memory remove operation.
This patch adds a memory isolation notifier and a memory hotplug notifier.
The memory isolation notifier will return the number of pages found in
the range specified. This is used to determine if all of the used pages
in a pageblock are owned by the balloon (or other entities in the notifier
chain). The hotplug notifier will free pages in the range which is to be
removed. The priority of this hotplug notifier is low so that it will be
called near last, this helps avoids removing loaned pages in operations
that fail due to other handlers.
CMM activity will be halted when hotplug remove operations are active and
resume activity after a delay period to allow the hypervisor time to
adjust.
Signed-off-by: Robert Jennings <rcj@linux.vnet.ibm.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Brian King <brking@linux.vnet.ibm.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Gerald Schaefer <geralds@linux.vnet.ibm.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* 'cpumask-cleanups' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
cpumask: rename tsk_cpumask to tsk_cpus_allowed
cpumask: don't recommend set_cpus_allowed hack in Documentation/cpu-hotplug.txt
cpumask: avoid dereferencing struct cpumask
cpumask: convert drivers/idle/i7300_idle.c to cpumask_var_t
cpumask: use modern cpumask style in drivers/scsi/fcoe/fcoe.c
cpumask: avoid deprecated function in mm/slab.c
cpumask: use cpu_online in kernel/perf_event.c
* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6:
OMAP3: serial - fix bug introduced in
mfd: twl: fix twl4030 rename for remaining driver, board files
USB ehci: replace mach header with plat
omap3: Allow EHCI to be built on OMAP3
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus: (71 commits)
MIPS: Lasat: Fix botched changes to sysctl code.
RTC: rtc-cmos.c: Fix warning on MIPS
MIPS: Cleanup random differences beween lmo and Linus' kernel.
MIPS: No longer hardwire CONFIG_EMBEDDED to y
MIPS: Fix and enhance built-in kernel command line
MIPS: eXcite: Remove platform.
MIPS: Loongson: Cleanups of serial port support
MIPS: Lemote 2F: Suspend CS5536 MFGPT Timer
MIPS: Excite: move iodev_remove to .devexit.text
MIPS: Lasat: Convert to proc_fops / seq_file
MIPS: Cleanup signal code initialization
MIPS: Modularize COP2 handling
MIPS: Move EARLY_PRINTK to Kconfig.debug
MIPS: Yeeloong 2F: Cleanup reset logic using the new ec_write function
MIPS: Yeeloong 2F: Add LID open event as the wakeup event
MIPS: Yeeloong 2F: Add basic EC operations
MIPS: Move several variables from .bss to .init.data
MIPS: Tracing: Make function graph tracer work with -mmcount-ra-address
MIPS: Tracing: Reserve $12(t0) for mcount-ra-address of gcc 4.5
MIPS: Tracing: Make ftrace for MIPS work without -fno-omit-frame-pointer
...
* 'next-spi' of git://git.secretlab.ca/git/linux-2.6:
spi: spi_txx9.c: use resource_size()
spi: spi_sh_sci.c: use resource_size()
spi: spi_mpc8xxx.c: use resource_size()
spi: spi_bfin5xx.c: use resource_size()
spi: atmel_spi.c: use resource_size()
spi: Add s3c64xx SPI Controller driver
atmel_spi: fix dma addr calculation for len > BUFFER_SIZE
spi_s3c24xx: add FIQ pseudo-DMA support
spi: controller driver for Designware SPI core
spidev: add proper section markers
spidev: use DECLARE_BITMAP instead of declaring the array
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm:
PCMCIA: fix pxa2xx_lubbock modular build error
[ARM] Update mach-types
[ARM] pxa: fix no reference of cpu_is_pxa25x() in devices.c
[ARM] pxa/cm-x300: add PWM backlight support
revert "[ARM] pxa/cm-x300: add PWM backlight support"
ARM: use flush_kernel_dcache_area() for dmabounce
ARM: add size argument to __cpuc_flush_dcache_page
ARM: 5848/1: kill flush_ioremap_region()
ARM: cache-l2x0: make better use of background cache handling
ARM: cache-l2x0: avoid taking spinlock for every iteration
[ARM] Kirkwood: Add LaCie Network Space v2 support
ARM: dove: fix the mm mmu flags of the pj4 procinfo
It says
Warning: objdump version is older than 2.19
Warning: Skipping posttest.
because it used the wrong field from `objdump -v':
akpm:/usr/src/25> /opt/crosstool/gcc-4.0.2-glibc-2.3.6/x86_64-unknown-linux-gnu/bin/x86_64-unknown-linux-gnu-objdump -v
GNU objdump 2.16.1
Copyright 2005 Free Software Foundation, Inc.
This program is free software; you may redistribute it under the terms of
the GNU General Public License. This program has absolutely no warranty.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
LKML-Reference: <200912172326.nBHNQaQl024796@imap1.linux-foundation.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: Masami Hiramatsu <mhiramat@redhat.com>
Commit 83ce4009 did the following change
If the TSC is constant and non-stop, also set it reliable.
But, there seems to be few systems that will end up with TSC warp across
sockets, depending on how the cpus come out of reset. Skipping TSC sync
test on such systems may result in time inconsistency later.
So, reenable TSC sync test even on constant and non-stop TSC systems.
Set, sched_clock_stable to 1 by default and reset it in
mark_tsc_unstable, if TSC sync fails.
This change still gives perf benefit mentioned in 83ce4009 for systems
where TSC is reliable.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Acked-by: Suresh Siddha <suresh.b.siddha@intel.com>
LKML-Reference: <20091217202702.GA18015@linux-os.sc.intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
* 'for-linus' of git://gitserver.sunplusct.com/linux-2.6-score:
score: include asm-generic/param.h in asm/delay.h.
score: fixed pfn_valid define.
score: add flush_dcahce_page and PG_dcache_dirty define
Proper Posix O_SYNC handling only made it into 2.6.33, not 2.6.32.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Add pseudo-DMA by FIQ to the S3C24XX SPI driver. This allows the driver
to get DMA-like performance where there are either no free DMA channels or
when doing transfers that required both TX and RX data paths.
Since this patch requires the addition of an assembly file to hold the FIQ
code, we rename the module (instead of adding a rename of the .c file to
this patch). We expect most users are loading this via udev and thus
there should be no change to the userland configuration.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Simtec Linux Team <linux@simtec.co.uk>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* 'for-33' of git://repo.or.cz/linux-kbuild: (29 commits)
net: fix for utsrelease.h moving to generated
gen_init_cpio: fixed fwrite warning
kbuild: fix make clean after mismerge
kbuild: generate modules.builtin
genksyms: properly consider EXPORT_UNUSED_SYMBOL{,_GPL}()
score: add asm/asm-offsets.h wrapper
unifdef: update to upstream revision 1.190
kbuild: specify absolute paths for cscope
kbuild: create include/generated in silentoldconfig
scripts/package: deb-pkg: use fakeroot if available
scripts/package: add KBUILD_PKG_ROOTCMD variable
scripts/package: tar-pkg: use tar --owner=root
Kbuild: clean up marker
net: add net_tstamp.h to headers_install
kbuild: move utsrelease.h to include/generated
kbuild: move autoconf.h to include/generated
drop explicit include of autoconf.h
kbuild: move compile.h to include/generated
kbuild: drop include/asm
kbuild: do not check for include/asm-$ARCH
...
Fixed non-conflicting clean merge of modpost.c as per comments from
Stephen Rothwell (modpost.c had grown an include of linux/autoconf.h
that needed to be changed to generated/autoconf.h)
The loop condition is fragile: we compare an unsigned value to zero, and
then decrement it by something larger than one in the loop. All the
callers should be passing in appropriately aligned buffer lengths, but
it's better to just not rely on it, and have some appropriate defensive
loop limits.
Acked-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Not all awk implementations (including the default awk in Ubuntu 9.10)
support POSIX character classes. Since x86-opcode-map.txt is plain
ASCII, we can just use explicit ranges for lower case, alphabetic, and
alphanumeric characters instead.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Acked-by: Masami Hiramatsu <mhiramat@redhat.com>
LKML-Reference: <adabphy750b.fsf@roland-alpha.cisco.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
It's just wasteful for stacktrace users like perf to walk
through every entries on the stack whereas these only accept
reliable ones, ie: that the frame pointer validates.
Since perf requires pure reliable stacktraces, it needs a stack
walker based on frame pointers-only to optimize the stacktrace
processing.
This might solve some near-lockup scenarios that can be triggered
by call-graph tracing timer events.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Paul Mackerras <paulus@samba.org>
LKML-Reference: <1261024834-5336-2-git-send-regression-fweisbec@gmail.com>
[ v2: fix for modular builds and small detail tidyup ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The current print_context_stack helper that does the stack
walking job is good for usual stacktraces as it walks through
all the stack and reports even addresses that look unreliable,
which is nice when we don't have frame pointers for example.
But we have users like perf that only require reliable
stacktraces, and those may want a more adapted stack walker, so
lets make this function a callback in stacktrace_ops that users
can tune for their needs.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Paul Mackerras <paulus@samba.org>
LKML-Reference: <1261024834-5336-1-git-send-regression-fweisbec@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
MAX_DMA_CHANNELS is tested for the total number of channels in order to
populate an IRQ map. Stub this out completely when no DMA support is
enabled -- as used to be the default behaviour before this was
generalized for use by the dmaengine code.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The cardbus code creates PCI devices without ever going through the
necessary fixup bits and pieces that normal PCI devices go through.
There's in fact a commented out call to pcibios_fixup_bus() in there,
it's commented because ... it doesn't work.
I could make pcibios_fixup_bus() do the right thing on powerpc easily
but I felt it cleaner instead to provide a specific hook pci_fixup_cardbus
for which a weak empty implementation is provided by the PCI core.
This fixes cardbus on powerbooks and probably all other PowerPC
platforms which was broken completely for ever on some platforms and
since 2.6.31 on others such as PowerBooks when we made the DMA ops
mandatory (since those are setup by the fixups).
Acked-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
There's no reason for MIPS to select EMBEDDED. In fact, EMBEDDED makes
MIPS more awkward to deal with because it makes it different to the
majority of architectures for no good reason.
[Ralf: Historically disabling EMBEDDED had hid essential options for many
MIPS platforms such as serial console and forced crap like VGA support
or power managment enabled for platforms where those don't make any sense.
The name of the option is also _very_ missleading so many users don't
select it even where is was required for a functioning kernel.]
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/663/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Currently, MIPS kernels silently overwrite kernel command-line parameters
hardcoded in CONFIG_CMDLINE by the ones received from firmware. Therefore,
using firmware remains the only reliable method to transfer the
command-line parameters, which is not always desirable or convenient, and
the CONFIG_CMDLINE option is thereby effectively rendered useless.
This patch fixes the problem described above and introduces a more flexible
scheme of handling the kernel command line, in a manner identical to what is
currently used for x86. The default behavior, i.e. when CONFIG_CMDLINE_BOOL
is not defined, retains the existing semantics, and firmware command-line
arguments override the hardcoded ones.
[Ralf: I fixed up all the defconfig files so the stay unaffected by this
change.]
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@movial.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/689/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The platform has never been fully merged
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Thomas Koeller <thomas.koeller@baslerweb.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mtd@lists.infradead.org
Acked-by: David Woodhouse <David.Woodhouse@intel.com>
Acked-by: Wim Van Sebroeck <wim@iguana.be>
This patchs uses a loongson_uart_base variable instead of the
uart_base[] array and adds a new kernel option to avoid to compile
uart_base.c all the time, which will save a little bit of memory for us.
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.orghttp://patchwork.linux-mips.org/patch/727/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
