Otherwise no PCM will be built for codecs without analog I/O.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Otherwise setting the capture volume for amps will be weird and
inconsistent (it will try to set values outside the range of the
second amp based on capabilities of the first amp).
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If the input node does not have any volume capable input amp,
don't add such a control.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Even a single DAC can output two channels, so the channel count
is twice the number of DACs.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We use knew->index for adc_idx when we create "Capture Volume" and
"Capture Switch", so use the same to retrieve adc_idx.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a new flag to indicate whether HP amp is turned on as default for
speaker or line-outs, and enable this for ALC260 codec, as many
machines with this codec require the HP amp even for speakers.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Sometimes (or rather often) BIOS sets the pin default configurations
obviously wrongly. Looking through these failures, one common pattern
is to enable some dead pins that are usually marked as speaker pins.
In such a case, we can skip them if the pins don't have the output
capability.
In this patch, add a check for the valid pin cap bit for each parsed
pin, and filter out when it's invalid.
The fix was originally suggested by Raymond Yau.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
CA0110 codec is a fairly straightforward hardware implementation,
and we can use the generic parser almost as is.
Just set spec->multi_cap_vol flag to follow the current behavior.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Replace the old parser code for C-Media auto-parser with the latest
generic parser. For compatibility reason, the static bindings are
still left, but they could be cleaned up in future.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The pincfgs, init_verbs and hints set by sysfs or patch might be
changed dynamically on the fly, thus we need to protect it.
Add a simple protection via a mutex.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As David Henningsson recently suggested, some HP laptops use an unused
mic pin for controlling a mute LED, and this information is provided
via DMI string "HP_Mute_LED_X_Y" string. This patch adds the generic
support for such cases, as we've already done in patch_sigmatel.c.
This is applied generically to all devices with ID 0x103c.
But as we don't know whether the device 103c:1586 really contains
HP_Mute_LED_X_Y DMI string, still keep the static setup for this
device using the mic2 pin 0x19.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some fixups such as setting the flags influencing on the parser
behavior should be applied before actually parsing the tree.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Try to recover from the regression: set the HP amp for the speaker and
add the hp jack mode enum as default.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add the enum controls for changing the headphone amp bits of output
jacks, such as "Headphone Jack Mode". This feature isn't enabled as
default, so far, unless spec->add_out_jack_modes flag is set.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When a multi-io jack is switched to another direction, call the
automute and autoswitch update functions, as this jack won't be used
as the headphone or the mic jack that may turn off others.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a new fixup type, HDA_FIXUP_PINCTLS, for overriding the pinctl
values of the given pins. It takes the same array of struct pintbl
like HDA_FIXUP_PINS, but each entry contains the pinctl value instead
of the pin default config value.
This patch also replaces the corresponding codes in patch_realtek.c.
Without this change, the direct call of verbs may be overridden again
by the later call of pinctl restoration by the driver.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now the whole codebase has been changed from the earlier kernels, it
makes little sense to keep these aliases. Simply replace with the
official names.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When a jack is retasked as a different direction (e.g. a mic jack is
used as a CLFE output), such a jack shouldn't be counted as the target
for the automatic jack switching. Skip the automute or the autoswitch
when the current pinctl direction is different from what we suppose.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use the new pin target accessors for managing the current pinctl
values in the generic parser. The pinctl values of all active pins
are once determined at the initialization phase, and stored via
snd_hda_codec_set_pin_target(). This will be referred again in the
codec init or resume phase to set the actual pinctl.
This value is kept while the auto-mute. When a line-out or a speaker
pin is muted by auto-mute, the driver simply disables the pin, but it
doesn't touch the cached pinctl target value. Upon unmute, this value
is used to restore the original pinctl in return.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Check more strictly about the validity of pinctl values in
snd_hda_set_pin_ctl() and correct the wrong bits automatically.
Also provide the helper function to correct pinctl bits to codec
drivers.
This automatically fixes the invalid pinctl writes that are found in
a few Realtek fixups for NID 0x0f amp like ASUS A6Rp.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We already have the list of whole pin widgets and there is an unused
space in the list; let's use it for caching the current pinctl value.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When a DAC is reassigned from surrounds to front or ADCs are reduced
due to incomplete imux, we clear the path indices but the path
instances remain as is. Since the paths might be still referred
through the whole path list parsing (e.g. is_active_nid()), we should
clear these path instances as well.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since some codecs can choose the aamix as a capture source, we should
support it as well. When spec->add_stereo_mix_input flag is set, the
parser checks the availability of aamix as the input source, and adds
the paths automatically when possible.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In the current parser code, the input_paths[] may become inconsistent
when some of detected ADCs are dropped due to incomplete inputs, since
the driver rearranges only adc_nids[] but doesn't touch input_paths[].
This patch fixes the issue, and also it optimizes the reachability
checks by simply referring to the parsed input_paths[] instead of
calling is_reachable() again for each connection.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Instead of handling special cases in the caller side, give a proper
name string "Headphone Mic" from hda_get_autocfg_input_label() when
the headhpone jack pin is specified as an input.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The capture paths shouldn't contain the analog loopback mixer.
Pass a proper argument to exclude the aamix NID.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a new flag spec->suppress_mic_auto_switch for codecs that don't
support unsol events properly like VT1708.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When the default config value shows the connection AC_JACK_PORT_BOTH,
it's better to handle it as a speaker pin. This makes the behavior
consistent in snd_hda_get_pin_label() and snd_hda_parse_pin_defcfg().
There are only few old machines showing this attribute, and all of
them are actually fixed speaker pins, as far as I know.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit modifies the definition of snd_hda_parse_nid_path()
slightly, now with_aa_mix argument is changed to anchor_nid, so that
it can handle any NID generically as an anchor point to include or
exclude.
The with_aa_mix field in struct nid_path is removed again by this
change.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The multi-io channels can vary not only from 1 to 6 but also may vary
from 6 to 8 or such. At the same time, there are more speaker pins
available than the primary output pins. So, we need three variables
to check: the minimum channel counts for primary outputs, the current
channel counts for primary outputs, and the minimum channel counts for
all outputs.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Instead of looking through paths with the dac -> pin connection at
each time, just pass the already parsed path index to
assign_out_path_ctls(). This simplifies the code a bit.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The path indices must be reset at each evaluation of DAC assignment.
Otherwise the badness value will be wrongly calculated and mixers may
be inconsistently assigned.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Let is_jack_detectable() return true when the jack polling is enabled
for the codec. VT1708 uses the polling explicitly so we need to allow
it.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The new hook which is called at each PCM playback ops.
It can be used to control the codec-specific power-saving feature in
each codec driver.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The bind-volume workaround was introduced for simplifying the mixer
abstraction in the case where one or more pins of multiple outputs
lack of individual volume controls. This was essentially the case
like Acer Aspire 5935, which has 5.1 speakers and 5.1 (multi-io)
jacks although there are 5 DACs, so some of them must share a DAC.
However, the recent code rewrite changed the DAC assignment policy to
share with the same channel instead of binding to the front, thus
binding the volumes for all channels makes little sense now, rather
it's confusing. So in this patch, the ugly workaround is finally
dropped and simply create the volume control corresponding to the
parsed path position.
For dual headphones or 2.1 speakers with a shared volume control, it's
anyway bound to the same DAC if needed, so this change shouldn't bring
any practical difference.
And, as a good bonus, we can cut off the whole code handling the bind
volume elements.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
