* Obsolete driver removals
- Removed obsolete adm1021 and max6642 drivers
* New drivers
- MPS MP2891
- MPS MP2993
- MPS MP9941
- MPS MP5920
- SPD5118 (Temperature Sensor and EEPROM)
* Added device support to existing drivers
- g762: G761
- dell-smm: Dell OptiPlex 7060
- asus-ec-sensors: ProArt X670E-CREATOR WIFI
- corsair-psu: HX1200i Series 2023 psu
- nzxt-smart2: Additional USB IS for NZXT RGB & Fan Controller
* Notable enhancements and fixes
- Removed use of i2c_match_id()
- Constified struct regmap_config where feasible
- Cleaned up amc6821 driver, and converted to use regmap and with_info API
- Converted max6639 driver to use with_info API; added support for
additional sysfs attributes
- Fixed various sysfs attribute underflows
- Added PEC support to hwmon core, and use in lm90 and max31827 drivers
* Various other minor fixes and improvements
-----BEGIN PGP SIGNATURE-----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=ebWS
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-v6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
"Obsolete driver removals:
- Removed obsolete adm1021 and max6642 drivers
New drivers:
- MPS MP2891, MP2993, MP9941, and MP5920
- SPD5118 (Temperature Sensor and EEPROM)
Added device support to existing drivers:
- g762: G761
- dell-smm: Dell OptiPlex 7060
- asus-ec-sensors: ProArt X670E-CREATOR WIFI
- corsair-psu: HX1200i Series 2023 psu
- nzxt-smart2: Additional USB IS for NZXT RGB & Fan Controller
Notable enhancements and fixes:
- Removed use of i2c_match_id()
- Constified struct regmap_config where feasible
- Cleaned up amc6821 driver, and converted to use regmap and
with_info API
- Converted max6639 driver to use with_info API; added support for
additional sysfs attributes
- Fixed various sysfs attribute underflows
- Added PEC support to hwmon core, and use in lm90 and max31827
drivers
And various other minor fixes and improvements"
* tag 'hwmon-for-v6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (103 commits)
hwmon: (max6697) Fix swapped temp{1,8} critical alarms
hwmon: (max6697) Fix underflow when writing limit attributes
hwmon: Remove obsolete adm1021 and max6642 drivers
hwmon: (pmbus/ltc4286) Drop unused i2c device ids
hwmon: (g762) Initialize fans after configuring clock
hwmon: (amc6821) Add support for pwm1_mode attribute
hwmon: (amc6821) Convert to with_info API
hwmon: (amc6821) Convert to use regmap
hwmon: (amc6821) Drop unnecessary enum chips
hwmon: (amc6821) Use BIT() and GENMASK()
hwmon: (amc6821) Use tabs for column alignment in defines
hwmon: (amc6821) Reorder include files, drop unnecessary ones
hwmon: (amc6821) Add support for fan1_target and pwm1_enable mode 4
hwmon: (amc6821) Rename fan1_div to fan1_pulses
hwmon: (amc6821) Make reading and writing fan speed limits consistent
hwmon: (amc6821) Stop accepting invalid pwm values
hwmon: (w83627ehf) Fix underflows seen when writing limit attributes
hwmon: (nct6775-core) Fix underflows seen when writing limit attributes
hwmon: (lm95234) Fix underflows seen when writing limit attributes
hwmon: (adc128d818) Fix underflows seen when writing limit attributes
...
ADM1021, MAX6642, and compatible chips are supported by the lm90 driver.
Remove the obsolete stand-alone drivers to reduce maintenance overhead.
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use regmap for register accesses and caching.
While at it, use sysfs_emit() instead of sprintf() to write sysfs
attribute data, and remove spurious debug messages which would only
be seen as result of a bug in the code. Also make sure that error
codes are propagated and not replaced with -EIO.
While at it, introduce rounding of written temperature values and for
internal calculations to reduce deviation from written values and as
much as possible.
No functional change intended except for differences introduced by
rounding.
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
With SPD5118 chip detection for the most part handled by the i2c-smbus
core using DMI information, the spd5118 driver no longer needs to
auto-detect spd5118 compliant chips.
Auto-detection by the driver is still needed on systems with no DMI support
or on systems with more than eight DIMMs and can not be removed entirely.
However, it affects boot time and introduces the risk of mis-identifying
chips. Add configuration option to be able to disable it on systems where
chip detection is handled outside the driver.
Cc: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Thomas Weißschuh <linux@weissschuh.net>
Tested-by: Armin Wolf <W_Armin@gmx.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for SPD5118 (Jedec JESD300) compliant temperature
sensors. Such sensors are typically found on DDR5 memory modules.
Cc: René Rebe <rene@exactcode.de>
Cc: Thomas Weißschuh <linux@weissschuh.net>
Reviewed-by: Thomas Weißschuh <linux@weissschuh.net>
Tested-by: Thomas Weißschuh <linux@weissschuh.net>
Tested-by: Stephen Horvath <s.horvath@outlook.com.au>
Tested-by: Armin Wolf <W_Armin@gmx.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The ChromeOS Embedded Controller exposes fan speed and temperature
readings.
Expose this data through the hwmon subsystem.
The driver is designed to be probed via the cros_ec mfd device.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20240529-cros_ec-hwmon-v4-2-5cdf0c5db50a@weissschuh.net
[tzungbi: Fixed typo in MAINTAINERS: "chros_ec_hwmon" -> "cros_ec_hwmon"]
Signed-off-by: Tzung-Bi Shih <tzungbi@kernel.org>
This addition adds in the ability for the system to scan
the EC chip in the Lenovo ThinkStation systems to get the
current fan RPM speeds the Maximum speed value for each
fan also provides the CPU, DIMM other thermal statuses
Signed-off-by: David Ober <dober6023@gmail.com>
Link: https://lore.kernel.org/r/20240328121250.331146-1-dober6023@gmail.com
[groeck: Dropped pointless case statements]
[Colin King: Fixed spelling error accesssible -> accessible]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Convert the module to be property provider agnostic and allow
it to be used on non-OF platforms.
Add mod_devicetable.h include.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20240404191323.3547465-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
In a future patch HAS_IOPORT=n will disable inb()/outb() and friends at
compile time. We thus need to add HAS_IOPORT as dependency for those
drivers using them.
Acked-by: Guenter Roeck <linux@roeck-us.net>
Co-developed-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Link: https://lore.kernel.org/r/20240404124700.3807842-2-schnelle@linux.ibm.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The driver support two functions: PWM and Tachometer. The PWM feature can
handle up to 16 output ports, while the Tachometer can monitor to up to 16
input ports as well. This driver implements them by exposing two kernel
subsystems: PWM and HWMON. The PWM subsystem can be utilized alongside
existing drivers for controlling elements such as fans (pwm-fan.c),
beepers (pwm-beeper.c) and so on. Through the HWMON subsystem, the driver
provides sysfs interfaces for fan.
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Link: https://lore.kernel.org/r/20240221104025.1306227-4-billy_tsai@aspeedtech.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This driver exposes hardware sensors of the ASUS ROG RYUJIN II 360
all-in-one CPU liquid cooler, which communicates through a proprietary
USB HID protocol. Report offsets were initially discovered in [1] by
Florian Freudiger.
Available sensors are pump, internal and external
(controller) fan speed in RPM, their duties in PWM, as well as
coolant temperature.
Attaching external fans to the controller is optional and allows them
to be controlled from the device. If not connected, the fan-related
sensors will report zeroes. The controller is a separate hardware unit
that comes bundled with the AIO and connects to it to allow fan control.
The addressable LCD screen is not supported in this
driver and should be controlled through userspace tools.
[1]: https://github.com/liquidctl/liquidctl/pull/653
Tested-by: Florian Freudiger <florian.freudiger@proton.me>
Signed-off-by: Aleksa Savic <savicaleksa83@gmail.com>
Link: https://lore.kernel.org/r/20240108094453.22986-1-savicaleksa83@gmail.com
[groeck: Add HID dependency]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This driver enables hardware monitoring support for NZXT Kraken
X53/X63/X73 and Z53/Z63/Z73 all-in-one CPU liquid coolers.
All models expose liquid temperature and pump speed (in RPM), as well as
PWM control (natively only through a temp-PWM curve, but the driver also
emulates fixed PWM control on top of that). The Z-series models
additionally expose the speed and duty of an optionally connected fan,
with the same PWM control capabilities.
Pump and fan duty control mode can be set through pwm[1-2]_enable,
where 1 is for the manual control mode and 2 is for the liquid temp
to PWM curve mode. Writing a 0 disables control of the channel through
the driver after setting its duty to 100%. As it is not possible to query
the device for the active mode, the driver keeps track of it.
The temperature of the curves relates to the fixed [20-59] C range, per
device limitations, and correlating to the detected liquid temperature.
Only PWM values (ranging from 0-255) can be set.
The addressable RGB LEDs and LCD screen, included only on Z-series models,
are not supported in this driver.
Co-developed-by: Jonas Malaco <jonas@protocubo.io>
Signed-off-by: Jonas Malaco <jonas@protocubo.io>
Co-developed-by: Yury Zhuravlev <stalkerg@gmail.com>
Signed-off-by: Yury Zhuravlev <stalkerg@gmail.com>
Signed-off-by: Aleksa Savic <savicaleksa83@gmail.com>
Link: https://lore.kernel.org/r/20240129111932.368232-1-savicaleksa83@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The Amphenol ChipCap 2 is a capacitive polymer humidity and temperature
sensor with an integrated EEPROM and minimum/maximum humidity alarms.
All device variants offer an I2C interface and depending on the part
number, two different output modes:
- CC2D: digital output
- CC2A: analog (PDM) output
This driver adds support for the digital variant (CC2D part numbers),
which includes the following part numbers:
- non-sleep measurement mode (CC2D23, CC2D25, CC2D33, CC2D35)
- sleep measurement mode (CC2D23S, CC2D25S, CC2D33S, CC2D35S)
The Chipcap 2 EEPROM can be accessed to configure a series of parameters
like the minimum/maximum humidity alarm threshold and hysteresis. The
EEPROM is only accessible in the command window after a power-on reset.
The default window lasts 10 ms if no Start_CM command is sent. After the
command window is finished (either after the mentioned timeout of after
a Start_NOM command is sent), the device enters the normal operation
mode and makes a first measurement automatically.
Unfortunately, the device does not provide any hardware or software
reset and therefore the driver must trigger power cycles to enter the
command mode. A dedicated, external regulator is required for that.
This driver keeps the device off until a measurement or access to the
EEPROM is required, making use of the first automatic measurement to
avoid different code paths for sleep and non-sleep devices.
The minimum and maximum humidity alarms are configured with two
registers per alarm: one stores the alarm threshold and the other one
keeps the value that turns off the alarm. The alarm signals are only
updated when a measurement is carried out.
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Link: https://lore.kernel.org/r/20240130-topic-chipcap2-v6-5-260bea05cf9b@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Adds a driver that provides read only access to the fan speed for Microsoft
Surface Pro devices. The fan speed is always regulated by the EC and cannot
be influenced directly.
Signed-off-by: Ivor Wanders <ivor@iwanders.net>
Link: https://github.com/linux-surface/kernel/pull/144
Reviewed-by: Maximilian Luz <luzmaximilian@gmail.com>
Reviewed-by: Armin Wolf <W_Armin@gmx.de>
Link: https://lore.kernel.org/r/20240131005856.10180-2-ivor@iwanders.net
[groeck:
- Declare surface_fan_hwmon_is_visible() static
- Add dependency on SURFACE_AGGREGATOR_BUS
]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The LTC4282 hot swap controller allows a board to be safely inserted and
removed from a live backplane. Using one or more external N-channel pass
transistors, board supply voltage and inrush current are ramped up at an
adjustable rate. An I2C interface and onboard ADC allows for monitoring
of board current, voltage, power, energy and fault status.
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20240129-b4-ltc4282-support-v4-3-fe75798164cc@analog.com
[groeck: clamp value range in ltc4282_write_voltage_byte_cached()]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This driver exposes hardware sensors of the Gigabyte AORUS Waterforce
all-in-one CPU liquid coolers, which communicate through a proprietary
USB HID protocol. Report offsets were initially discovered in [1] and
confirmed by me on a Waterforce X240 by observing the sent reports from
the official software.
Available sensors are pump and fan speed in RPM, as well as coolant
temperature. Also available through debugfs is the firmware version.
Attaching a fan is optional and allows it to be controlled from the
device. If it's not connected, the fan-related sensors will report
zeroes.
The addressable RGB LEDs and LCD screen are not supported in this
driver and should be controlled through userspace tools.
[1]: https://github.com/liquidctl/liquidctl/issues/167
Signed-off-by: Aleksa Savic <savicaleksa83@gmail.com>
Link: https://lore.kernel.org/r/20231207122402.107032-1-savicaleksa83@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Some Dell machines like the Dell Optiplex 7000 do not support
the legacy SMM interface, but instead expect all SMM calls
to be issued over a special WMI interface.
Add support for this interface so users can control the fans
on those machines.
Tested-by: <serverror@serverror.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://lore.kernel.org/r/20231123004820.50635-8-W_Armin@gmx.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for LTC2991 Octal I2C Voltage, Current, and Temperature
Monitor.
The LTC2991 is used to monitor system temperatures, voltages and
currents. Through the I2C serial interface, the eight monitors can
individually measure supply voltages and can be paired for
differential measurements of current sense resistors or temperature
sensing transistors. Additional measurements include internal
temperature and internal VCC.
Signed-off-by: Antoniu Miclaus <antoniu.miclaus@analog.com>
Link: https://lore.kernel.org/r/20231026103413.27800-2-antoniu.miclaus@analog.com
[groeck: Fixed up documentation warning]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The two drivers compile fine on arm64, powerpc, m68k and s390. So make
it possible to enable the drivers in the presence of COMPILE_TEST.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230918085951.1234172-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Accessing virtual registers is very inefficient, so pwm map values
should be cached when possible, else userspace could effectively do
a DOS attack by reading pwm map values in a while loop.
Use the regmap cache to cache those values.
Tested on a Fujitsu Esprimo P720.
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://lore.kernel.org/r/20230907052639.16491-4-W_Armin@gmx.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
POWER-Z is a series of devices to monitor power characteristics of
USB-C connections and display those on a on-device display.
Some of the devices, notably KM002C and KM003C, contain an additional
port which exposes the measurements via USB.
This is a driver for this monitor port.
It was developed and tested with the KM003C.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Link: https://lore.kernel.org/r/20230902-powerz-v4-1-7ec2c1440687@weissschuh.net
[groeck:
Release urb after hwmon registration error;
Move priv->status initialization to correct place before reinit_completion
]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add base support for Renesas HS3001 temperature
and humidity sensors and its compatibles HS3002,
HS3003 and HS3004.
The sensor has a fix I2C address 0x44. The resolution
is fixed to 14bit (ref. Missing feature).
Missing feature:
- Accessing non-volatile memory: Custom board has no
possibility to control voltage supply of sensor. Thus,
we cannot send the necessary control commands within
the first 10ms after power-on.
Signed-off-by: Andre Werner <andre.werner@systec-electronic.com>
Link: https://lore.kernel.org/r/20230725042207.22310-2-andre.werner@systec-electronic.com
[groeck: Cosmetic documentation fixup; added documentation to index;
replaced probe_new with probe dropped unused variable]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
SMM665 and related chips are power controller/sequencer chips from
Summit Microelectronics. The company was acquired by Qualcomm in 2012,
and support for the chip series stopped.
The chips are long since gone from active use, making the driver
unsupportable and just consuming space and compile time. Remove it.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Hewlett-Packard (and some HP Compaq) business-class computers report
hardware monitoring information via WMI. This driver exposes that
information to hwmon.
Initial support is provided for temperature, fan speed, and intrusion
sensor types. Provisional support is provided for voltage and current
sensor types.
HP's WMI implementation permits many other types of numeric sensors.
Therefore, a debugfs interface is also provided to enumerate and
inspect all numeric sensors visible on the WMI side. This should
facilitate adding support for other sensor types in the future.
Tested on a HP Z420, a HP EliteOne 800 G1, and a HP Compaq Elite 8300
SFF.
Note that provisionally supported sensor types are untested and seem
to be rare-to-nonexistent in the wild, having been encountered
neither on test systems nor in ACPI dumps from the Linux Hardware
Database. They are included because their popularity in general makes
their presence on past or future HP systems plausible and because no
doubt exists as to how the sensors themselves would be represented in
WMI (alarm attributes will need to wait for hardware to be located).
A 2005 HP whitepaper gives the relevant sensor object MOF definition
and sensor value scaling calculation, and both this driver and the
official HP Performance Advisor utility comply with them (confirmed
in the latter case by reverse engineering).
Link: https://h20331.www2.hp.com/hpsub/downloads/cmi_whitepaper.pdf
Signed-off-by: James Seo <james@equiv.tech>
Link: https://lore.kernel.org/r/20230522115645.509701-1-james@equiv.tech
[groeck: Set error return value for intrusion writes to -EINVAL.
Always accept writes of 0 even if there was no intrusion. ]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
MAX31827 is a low-power temperature switch with I2C interface.
The device is a ±1°C accuracy from -40°C to +125°C
(12 bits) local temperature switch and sensor with I2C/SM-
Bus interface. The combination of small 6-bump wafer-lev-
el package (WLP) and high accuracy makes this temper-
ature sensor/switch ideal for a wide range of applications.
Signed-off-by: Daniel Matyas <daniel.matyas@analog.com>
Link: https://lore.kernel.org/r/20230524160131.14081-2-daniel.matyas@analog.com
[groeck: Improved define alignment, return -EINVAL after bad user input,
fixed up compatible statement]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for compatible AHT20 temperature/humidity sensor. The only
difference between the two is that AHT20 has additional crc8 byte.
It seems like AHT15 is also supported by the driver but it wasn't
verified and tested yet.
Tested on Beaglebone black rev C.
Signed-off-by: Kirill Yatsenko <kiriyatsenko@gmail.com>
Link: https://lore.kernel.org/r/20230524201912.815993-1-kiriyatsenko@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add driver for the StarFive JH71x0 temperature sensor. You
can enable/disable it and read temperature in milli Celcius
through sysfs.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Co-developed-by: Samin Guo <samin.guo@starfivetech.com>
Signed-off-by: Samin Guo <samin.guo@starfivetech.com>
Signed-off-by: Hal Feng <hal.feng@starfivetech.com>
Link: https://lore.kernel.org/r/20230321022644.107027-3-hal.feng@starfivetech.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
- Change MFD support status from Supported to Maintained
- New Drivers
- Add support for the Intel Platform Management Component Interface (PMCI)
- Remove Drivers
- HTC PASIC3 LED/DS1WM
- Toshiba T7L66XB, TC6387XB and TC6393XB TMIO
- New Device Support
- Add support for N6000 Flash to Intel M10 BMC PMCI
- Add support for Lenovo Yoga Tab 3 to Intel CHTWC PMIC
- New Functionality
- Provide Reset support to Syscon
- Fix-ups
- Explicitly provide missing include files
- Pass platform type data/info via the SPI/I2C/DT registration strategy
- Lots of DT documentation / adaptions
- Replace scnprintf() with preferred sysfs_emit()
- Remove unused / superfluous code
- Fix some trivial whitesspace / spelling / grammatical issues
- Replace pm_power_off with new and improved register_sys_off_handler() API
- Bug Fixes
- Reintroduce RK808-clkout registration - fixing Wi-Fi and Bluetooth
- Repair the order of AXPxxx IRQ PEK RISE/FALL definitions
- Refuse to build CS5535 on unsupported UML architectures
- Fix memory leaks in error return paths
- Prevent refcount leaks in error return paths
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEdrbJNaO+IJqU8IdIUa+KL4f8d2EFAmP3KQ8ACgkQUa+KL4f8
d2FAFw//deQpWVTX8CBdgHtCTxkLymussYgvnlJwJhoD8RYpTyFme9drVSBX9Msi
C3rRX3RQCu114xUVMt5JIVTZbbbx2zjDI9HGSmh3lOIW0vh9/oW6/bUO/PFw6/C3
v4AkzMYIwE9O4g9DbM9WWR/uickYyKobS8VXMupyWYnVbF361UOCFChCMrm+3Kl1
S+grj1/fKxiCJxF/L+Iij06PQtCGGZBxN2JNqsTHj7IyUjA2JZyvXvV3pJ/MtIQv
w+hb+xYK13uCG4JUI6xOHkJU7/gNCwpsz1TJoR7CuXl6JBIP/oVIw9fJ4N1eZ1Zr
ioBEBIrEmKF1Hihd8iP5prE1BV5WvE6s9hqTdqn3qJPaH9+Rp8sExuDcq6gzE7Lc
c5eVhA0uSXQM62pz4rqwkfzPX8BFMvZ1Ii9ukyWaAb1Lyz2f5tFu5E2gd6vjXVVP
yId3H43eQVrutlZAbP+txhN7VDSf/OunUrOEDw9VbLe2sB/rBta2De0tFfpE5lAg
McOfyNvclqwTXuakNB0sg2Sg3DhxMTKQhnQQAj7E/DmcYVhQTFQPVj69BtERIldf
9VHsAg3Kp93A/w5/J/3HOqMexHWpZ6eiW05Xu1zwGtWhx70c1YWMmMhMJk1zf/T+
G8Drk+fuhsycsGu/7MkY+NuqIqIM3JVb4Hqa/HYN+L/iPJXLAxI=
=f0fr
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"Core Framework:
- Change MFD support status from Supported to Maintained
New Drivers:
- Add support for the Intel Platform Management Component Interface
(PMCI)
Removed Drivers:
- HTC PASIC3 LED/DS1WM
- Toshiba T7L66XB, TC6387XB and TC6393XB TMIO
New Device Support:
- Add support for N6000 Flash to Intel M10 BMC PMCI
- Add support for Lenovo Yoga Tab 3 to Intel CHTWC PMIC
New Functionality:
- Provide Reset support to Syscon
Fix-ups:
- Explicitly provide missing include files
- Pass platform type data/info via the SPI/I2C/DT registration
strategy
- Lots of DT documentation / adaptions
- Replace scnprintf() with preferred sysfs_emit()
- Remove unused / superfluous code
- Fix some trivial whitesspace / spelling / grammatical issues
- Replace pm_power_off with new and improved
register_sys_off_handler() API
Bug Fixes:
- Reintroduce RK808-clkout registration - fixing Wi-Fi and Bluetooth
- Repair the order of AXPxxx IRQ PEK RISE/FALL definitions
- Refuse to build CS5535 on unsupported UML architectures
- Fix memory leaks in error return paths
- Prevent refcount leaks in error return paths"
* tag 'mfd-next-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (40 commits)
dt-bindings: mfd: qcom,tcsr: Add compatible for IPQ5332
dt-bindings: mfd: Add NXP BBNSM
mfd: ntxec: Add version number for EC in Tolino Vision
dt-bindings: mfd: syscon: Add mt8365-syscfg
mfd: Remove toshiba tmio drivers
mfd: arizona: Use pm_runtime_resume_and_get() to prevent refcnt leak
mfd: syscon: Allow reset control for syscon devices
dt-bindings: mfd/syscon: Add resets property
dt-bindings: mfd: syscon: Add amd,pensando-elba-syscon compatible
dt-bindings: mfd: qcom,tcsr: Add compatible for MSM8226
mfd: simple-mfd-i2c: Fix incoherent comment regarding DT registration
mfd: axp20x: Switch to the sys-off handler API
mfd: core: Spelling s/compement/complement/
mfd: max8925: Remove the unused function irq_to_max8925()
mfd: qcom-pm8xxx: Remove set but unused variable 'rev'
dt-bindings: mfd: syscon: Document GXP register compatible
mfd: twl4030-power: Drop empty platform remove function
mfd: twl: Fix TWL6032 phy vbus detection
mfd: pcf50633-adc: Fix potential memleak in pcf50633_adc_async_read()
MAINTAINERS: Move MFD from a Supported to Maintaied state
...
- New drivers
* Infineon TDA38640 Voltage Regulator
* NXP MC34VR500 PMIC
* GXP fan controller
* MPQ7932 Power Management IC
- New chip or board support added to existing drivers
* it87: IT87952E; also other cleanup/improvements
* intel-m10-bmc-hwmon: N6000
* pmbus/max16601: MAX16600
* aquacomputer_d5next: Aquacomputer Aquastream Ultimate, Aquacomputer Poweradjust 3,
Aquacomputer Aquaero
* nct6775: Support for B650/B660/X670 ASUS boards
* oxp-sensors: AYANEO AIR and AIR Pro
- Other notable changes
* Various kernel documentation fixes
* Various devicetree bindings fixes
* Explicitly deprecated [devm_]hwmon_device_register_with_groups
* ftsteutates: Support for fanX_fault and other cleanup
* ltc2945: Support for setting shunt resistor and other cleanup/fixes
* coretemp: Avoid RDMSR interrupts to isolated CPUs,
and simplify platform device handling
- Vaious other minoc cleanups and fixes
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEEiHPvMQj9QTOCiqgVyx8mb86fmYEFAmP09dcACgkQyx8mb86f
mYGXqxAArB9RNWemn18582Fg49ME9wkRDT+ZFPMKDSupjOgW+EXZZi86FPfIzl/c
PO9g4E/I3PZBgJddc16F2JPmg10JZlExQ+iOwCWQrviAEoBdxjBGoXWC5JhcnU6O
VCsn2nCsBwBcbBk2wqVuksvsRQIvRX/BeiTE0xw6yIQgGqEava7au2Av3W0NEX0+
ItPNQ9vqzp4ikufeY6Y2FoGM0PfVWSIulqDZoDhhqTdSDI4VnAcOdiies9Z4oaG2
pN+AwO+iNqQcbUiZyhUJz39j6+ywkhSxZJOsprsG6KA0shFwaR0N/3vCqZAxo8so
KaKJCGM6mkUqOBfmAeX6/kj1DuSvkR6+WixABbmk15AJIIoFHCeG9kTEHwTj7Ovk
vZ3rpZFCpTtCtlTCbMFFe/EW7ssbkucOJVtpaqWBtC7X/+rZO2LGMXQSA9tJW9N1
qGKbbxlwsxnVc1rIb7FM5QdoxMhbv+h4N7fJ/M6WDHg35xiEfugI9R9KvMv0P5+A
Z4CvIjeeUm8XjET1+3pKhpScXdVGdueuRO2SZ/NSAb7x4zdB/GPX4NELASWHvxXl
rFrfe7tvEtkIDAONeqYrA9wBCaH0YfqJHyTBz9UqQegp+3nA7mA+4PxVpAA6ntUq
0CuzS4NGxFVX7bPy3ONCQ+kViCQ76nXG2F4/TLL8lmwRZqkaTOM=
=yXoY
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-v6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
"New drivers:
- Infineon TDA38640 Voltage Regulator
- NXP MC34VR500 PMIC
- GXP fan controller
- MPQ7932 Power Management IC
New chip or board support added to existing drivers:
- it87: IT87952E; also other cleanup/improvements
- intel-m10-bmc-hwmon: N6000
- pmbus/max16601: MAX16600
- aquacomputer_d5next: Aquacomputer Aquastream Ultimate, Aquacomputer
Poweradjust 3, Aquacomputer Aquaero
- nct6775: Support for B650/B660/X670 ASUS boards
- oxp-sensors: AYANEO AIR and AIR Pro
Other notable changes:
- Various kernel documentation fixes
- Various devicetree bindings fixes
- Explicitly deprecated [devm_]hwmon_device_register_with_groups
- ftsteutates: Support for fanX_fault and other cleanup
- ltc2945: Support for setting shunt resistor and other cleanup/fixes
- coretemp: Avoid RDMSR interrupts to isolated CPUs, and simplify
platform device handling
... and various other minor cleanups and fixes"
* tag 'hwmon-for-v6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (66 commits)
hwmon: Deprecate [devm_]hwmon_device_register_with_groups
hwmon: (mlxreg-fan) Return zero speed for broken fan
hwmon: (gxp-fan-ctrl) use devm_platform_get_and_ioremap_resource()
hwmon: (aquacomputer_d5next) Add support for Aquacomputer Aquastream Ultimate
hwmon: (aquacomputer_d5next) Add support for Aquacomputer Poweradjust 3
hwmon: (iio_hwmon) use dev_err_probe
hwmon: intel-m10-bmc-hwmon: Add N6000 sensors
Docs/hwmon/index: Add missing SPDX License Identifier
hwmon: (it87) Updated documentation for recent updates to it87
hwmon: (it87) Add new chipset IT87952E
hwmon: (it87) Allow multiple chip IDs for force_id
hwmon: (it87) Add chip_id in some info message
hwmon: (it87) List full chip model name
hwmon: (it87) Disable configuration exit for certain chips
hwmon: (it87) Allow disabling exiting of configuration mode
Documentation: hwmon: correct spelling
hwmon: (pmbus/max16601) Add support for MAX16600
hwmon: (ltc2945) Allow setting shunt resistor
hwmon: (ltc2945) Handle error case in ltc2945_value_store
hwmon: (ltc2945) Add devicetree match table
...
New ASUS B650/B660/X670 boards firmware have not exposed WMI monitoring
GUID and entrypoint method WMBD could be implemented for different device
UID.
Implement the direct call to entrypoint method for monitoring the device
UID of B550/X570 boards.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=204807
Signed-off-by: Denis Pauk <pauk.denis@gmail.com>
Co-developed-by: Ahmad Khalifa <ahmad@khalifa.ws>
Signed-off-by: Ahmad Khalifa <ahmad@khalifa.ws>
Link: https://lore.kernel.org/r/20230111212241.7456-1-pauk.denis@gmail.com
[groeck: Fix multi-line formatting]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The GXP SoC can support up to 16 fans through the interface provided by
the CPLD. The current support is limited to 8 fans. The fans speeds are
controlled via 8 different PWMs which can vary in value from 0-255. The
fans are also capable of reporting if they have failed to the CPLD which
in turn reports the status to the GXP SoC.
Signed-off-by: Nick Hawkins <nick.hawkins@hpe.com>
Link: https://lore.kernel.org/r/20230103203654.59322-2-nick.hawkins@hpe.com
[groeck: Improved alignment of defined, added missing include linux/bits.h]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Split the common code from intel-m10-bmc driver into intel-m10-bmc-core
and move the SPI bus parts into an interface specific file.
intel-m10-bmc-core becomes the core MFD functions which can support
multiple bus interface like SPI bus.
Co-developed-by: Tianfei zhang <tianfei.zhang@intel.com>
Signed-off-by: Tianfei zhang <tianfei.zhang@intel.com>
Reviewed-by: Russ Weight <russell.h.weight@intel.com>
Acked-by: Guenter Roeck <linux@roeck-us.net> # hwmon
Reviewed-by: Xu Yilun <yilun.xu@intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230116100845.6153-5-ilpo.jarvinen@linux.intel.com
The s3c adc driver was removed along with the s3c24xx platform, so the
hwmon driver is orphaned and can be removed.
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Sensors driver for OXP Handhelds from One-Netbook that expose fan reading
and control via hwmon sysfs.
As far as I could gather all OXP boards have the same DMI strings and
they can be told appart only by the boot cpu vendor (Intel/AMD).
Currently only AMD boards are supported since Intel have different EC
registers and values to read/write.
Fan control is provided via pwm interface in the range [0-255]. AMD
boards have [0-100] as range in the EC, the written value is scaled to
accommodate for that.
Signed-off-by: Joaquín Ignacio Aramendía <samsagax@gmail.com>
Link: https://lore.kernel.org/r/20221104140659.593608-1-samsagax@gmail.com
[groeck: Removed misleading comment about module_platform_driver()]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Switch the jc42 driver to use an I2C regmap to access the registers.
Also move over to regmap's built-in caching instead of adding a
custom caching implementation. This works for JC42_REG_TEMP_UPPER,
JC42_REG_TEMP_LOWER and JC42_REG_TEMP_CRITICAL as these values never
change except when explicitly written. The cache For JC42_REG_TEMP is
dropped (regmap can't cache it because it's volatile, meaning it can
change at any time) as well for simplicity and consistency with other
drivers.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20221023213157.11078-2-martin.blumenstingl@googlemail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This commit adds support for Ampere SMpro hwmon driver. This driver
supports accessing various CPU sensors provided by the SMpro co-processor
including temperature, power, voltages, and current.
Signed-off-by: Quan Nguyen <quan@os.amperecomputing.com>
Link: https://lore.kernel.org/r/20220929094321.770125-2-quan@os.amperecomputing.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add a specific MFD_SY7636A config option.
As part of this change we can use MFD_SY7636A as a dependency for all
SY7636a components and also remove the name from MFD_SIMPLE_MFD_I2C as
it no longer needs to be selectable.
Signed-off-by: Alistair Francis <alistair@alistair23.me>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20220525115554.430971-2-alistair@alistair23.me
MAX31760 is a precision fan speed controller with nonvolatile lookup table.
Device has one internal and one external temperature sensor support.
Controls two fans and measures their speeds. Generates hardware alerts when
programmable max and critical temperatures are exceeded.
Signed-off-by: Ibrahim Tilki <Ibrahim.Tilki@analog.com>
Reviewed-by: Nurettin Bolucu <Nurettin.Bolucu@analog.com>
Link: https://lore.kernel.org/r/20220910171945.48088-2-Ibrahim.Tilki@analog.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The SENSORS_ASPEED is part of the Aspeed silicon so it makes
sense to depend on ARCH_ASPEED and for compile testing.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Link: https://lore.kernel.org/r/20220916120936.372591-1-pbrobinson@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Extend aquacomputer_d5next driver to expose various hardware
sensors of the Aquacomputer High Flow Next flow sensor, which
communicates through a proprietary USB HID protocol.
The High Flow Next exposes +5V voltages, water quality, conductivity
and flow readings. A temperature sensor can be connected to it, in
which case it provides its reading and an estimation of the
dissipated/absorbed power in the liquid cooling loop.
Additionally, serial number and firmware version are exposed through
debugfs.
Registry offsets were discovered and tested by users on Github [1] [2].
[1] https://github.com/aleksamagicka/aquacomputer_d5next-hwmon/issues/8
[2] https://github.com/aleksamagicka/aquacomputer_d5next-hwmon/pull/34
Signed-off-by: Aleksa Savic <savicaleksa83@gmail.com>
Link: https://lore.kernel.org/r/20220907100739.806571-1-savicaleksa83@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add driver for Microchip EMC2301/2/3/5 RPM-based PWM Fan Speed Controller.
Modify Makefile and Kconfig to support Microchip EMC2305 RPM-based
PWM Fan Speed Controller.
Signed-off-by: Michael Shych <michaelsh@nvidia.com>
Reviewed-by: Vadim Pasternak <vadimp@nvidia.com>
Link: https://lore.kernel.org/r/20220810171552.56417-3-michaelsh@nvidia.com
[groeck: Drop unnecessary () around DIV_ROUND_CLOSEST()]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This driver utilises a WMI interface found in AMD 500 series ASUS boards,
to read EC registers. But it turned out that ASUS abandoned the
interface, as it disappeared from Intel 600 series boards. Additionally,
the WMI interface was incredibly slow. Therefore this driver was deprecated
in favor of the asus_ec_sensors driver, which supports more boards, more
sensors, and is faster.
Signed-off-by: Eugene Shalygin <eugene.shalygin@gmail.com>
Link: https://lore.kernel.org/r/20220720072016.102086-2-eugene.shalygin@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Extend aquacomputer_d5next driver to expose hardware temperature sensors
and fans of the Aquacomputer Quadro fan controller, which communicates
through a proprietary USB HID protocol. Implemented by Jack Doan [1].
Four temperature sensors and PWM controllable fans are available. The
liquid flow sensor is also exposed, implemented by Leonard Anderweit [2].
Additionally, serial number, firmware version and power-on count are
exposed through debugfs.
This driver has been tested on x86_64.
[1] https://github.com/aleksamagicka/aquacomputer_d5next-hwmon/pull/5
[2] https://github.com/aleksamagicka/aquacomputer_d5next-hwmon/pull/9
Originally-from: Jack Doan <me@jackdoan.com>
Originally-from: Leonard Anderweit <leonard.anderweit@gmail.com>
Signed-off-by: Aleksa Savic <savicaleksa83@gmail.com>
Link: https://lore.kernel.org/r/20220727100606.9328-1-savicaleksa83@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The two drivers compile just fine on ARCH=arm. Allow to select
these drivers if COMPILE_TEST is enabled.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Link: https://lore.kernel.org/r/20220527153445.1871086-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
NE1618 is similar to NE1617 but supports manufacturer and chip ID
registers as well as 11 bit external temperature resolution.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
