dev_pm_ops are not supposed to change at runtime. All functions
working with dev_pm_ops provided by <linux/device.h> work with const
dev_pm_ops. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
19057 392 0 19449 4bf9 drivers/net/ethernet/freescale/gianfar.o
File size After adding 'const':
text data bss dec hex filename
19249 192 0 19441 4bf1 drivers/net/ethernet/freescale/gianfar.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_pm_ops are not supposed to change at runtime. All functions
working with dev_pm_ops provided by <linux/device.h> work with const
dev_pm_ops. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
18709 401 0 19110 4aa6 drivers/net/ethernet/smsc/smc91x.o
File size After adding 'const':
text data bss dec hex filename
18901 201 0 19102 4a9e drivers/net/ethernet/smsc/smc91x.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_pm_ops are not supposed to change at runtime. All functions
working with dev_pm_ops provided by <linux/device.h> work with const
dev_pm_ops. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
15426 1256 0 16682 412a drivers/net/ethernet/ibm/ibmveth.o
File size After adding 'const':
text data bss dec hex filename
15618 1064 0 16682 412a drivers/net/ethernet/ibm/ibmveth.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Leaking kernel addresses on unpriviledged is generally disallowed,
for example, verifier rejects the following:
0: (b7) r0 = 0
1: (18) r2 = 0xffff897e82304400
3: (7b) *(u64 *)(r1 +48) = r2
R2 leaks addr into ctx
Doing pointer arithmetic on them is also forbidden, so that they
don't turn into unknown value and then get leaked out. However,
there's xadd as a special case, where we don't check the src reg
for being a pointer register, e.g. the following will pass:
0: (b7) r0 = 0
1: (7b) *(u64 *)(r1 +48) = r0
2: (18) r2 = 0xffff897e82304400 ; map
4: (db) lock *(u64 *)(r1 +48) += r2
5: (95) exit
We could store the pointer into skb->cb, loose the type context,
and then read it out from there again to leak it eventually out
of a map value. Or more easily in a different variant, too:
0: (bf) r6 = r1
1: (7a) *(u64 *)(r10 -8) = 0
2: (bf) r2 = r10
3: (07) r2 += -8
4: (18) r1 = 0x0
6: (85) call bpf_map_lookup_elem#1
7: (15) if r0 == 0x0 goto pc+3
R0=map_value(ks=8,vs=8,id=0),min_value=0,max_value=0 R6=ctx R10=fp
8: (b7) r3 = 0
9: (7b) *(u64 *)(r0 +0) = r3
10: (db) lock *(u64 *)(r0 +0) += r6
11: (b7) r0 = 0
12: (95) exit
from 7 to 11: R0=inv,min_value=0,max_value=0 R6=ctx R10=fp
11: (b7) r0 = 0
12: (95) exit
Prevent this by checking xadd src reg for pointer types. Also
add a couple of test cases related to this.
Fixes: 1be7f75d16 ("bpf: enable non-root eBPF programs")
Fixes: 17a5267067 ("bpf: verifier (add verifier core)")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver currently creates RX/TX queues during device probe, but
assigns IRQ's to them during device open. On reset, however,
IRQ's are assigned when resetting the queues. If there is a reset
while the device is closed and the device is later opened, the driver will
request IRQ's twice, causing the open to fail. This patch assigns
the IRQ's in the ibmvnic_init function after the queues are reset or
initialized, ensuring IRQ's are only requested once.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add to RTNL_FAMILY_IPMR, RTM_GETROUTE the ability
to retrieve one S,G mroute from a specified table.
*,G will return mroute information for just that
particular mroute if it exists. This is because
it is entirely possible to have more S's then
can fit in one skb to return to the requesting
process.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The index is off-by-one when fp->aux->stack_depth
has already been rounded up to 32. In particular,
if stack_depth is 512, the index will be 16.
The fix is to round_up and then takes -1 instead of round_down.
[ 22.318680] ==================================================================
[ 22.319745] BUG: KASAN: global-out-of-bounds in bpf_prog_select_runtime+0x48a/0x670
[ 22.320737] Read of size 8 at addr ffffffff82aadae0 by task sockex3/1946
[ 22.321646]
[ 22.321858] CPU: 1 PID: 1946 Comm: sockex3 Tainted: G W 4.12.0-rc6-01680-g2ee87db3a287 #22
[ 22.323061] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.9.3-1.el7.centos 04/01/2014
[ 22.324260] Call Trace:
[ 22.324612] dump_stack+0x67/0x99
[ 22.325081] print_address_description+0x1e8/0x290
[ 22.325734] ? bpf_prog_select_runtime+0x48a/0x670
[ 22.326360] kasan_report+0x265/0x350
[ 22.326860] __asan_report_load8_noabort+0x19/0x20
[ 22.327484] bpf_prog_select_runtime+0x48a/0x670
[ 22.328109] bpf_prog_load+0x626/0xd40
[ 22.328637] ? __bpf_prog_charge+0xc0/0xc0
[ 22.329222] ? check_nnp_nosuid.isra.61+0x100/0x100
[ 22.329890] ? __might_fault+0xf6/0x1b0
[ 22.330446] ? lock_acquire+0x360/0x360
[ 22.331013] SyS_bpf+0x67c/0x24d0
[ 22.331491] ? trace_hardirqs_on+0xd/0x10
[ 22.332049] ? __getnstimeofday64+0xaf/0x1c0
[ 22.332635] ? bpf_prog_get+0x20/0x20
[ 22.333135] ? __audit_syscall_entry+0x300/0x600
[ 22.333770] ? syscall_trace_enter+0x540/0xdd0
[ 22.334339] ? exit_to_usermode_loop+0xe0/0xe0
[ 22.334950] ? do_syscall_64+0x48/0x410
[ 22.335446] ? bpf_prog_get+0x20/0x20
[ 22.335954] do_syscall_64+0x181/0x410
[ 22.336454] entry_SYSCALL64_slow_path+0x25/0x25
[ 22.337121] RIP: 0033:0x7f263fe81f19
[ 22.337618] RSP: 002b:00007ffd9a3440c8 EFLAGS: 00000202 ORIG_RAX: 0000000000000141
[ 22.338619] RAX: ffffffffffffffda RBX: 0000000000aac5fb RCX: 00007f263fe81f19
[ 22.339600] RDX: 0000000000000030 RSI: 00007ffd9a3440d0 RDI: 0000000000000005
[ 22.340470] RBP: 0000000000a9a1e0 R08: 0000000000a9a1e0 R09: 0000009d00000001
[ 22.341430] R10: 0000000000000000 R11: 0000000000000202 R12: 0000000000010000
[ 22.342411] R13: 0000000000a9a023 R14: 0000000000000001 R15: 0000000000000003
[ 22.343369]
[ 22.343593] The buggy address belongs to the variable:
[ 22.344241] interpreters+0x80/0x980
[ 22.344708]
[ 22.344908] Memory state around the buggy address:
[ 22.345556] ffffffff82aad980: 00 00 00 04 fa fa fa fa 04 fa fa fa fa fa fa fa
[ 22.346449] ffffffff82aada00: 00 00 00 00 00 fa fa fa fa fa fa fa 00 00 00 00
[ 22.347361] >ffffffff82aada80: 00 00 00 00 00 00 00 00 00 00 00 00 fa fa fa fa
[ 22.348301] ^
[ 22.349142] ffffffff82aadb00: 00 01 fa fa fa fa fa fa 00 00 00 00 00 00 00 00
[ 22.350058] ffffffff82aadb80: 00 00 07 fa fa fa fa fa 00 00 05 fa fa fa fa fa
[ 22.350984] ==================================================================
Fixes: b870aa901f ("bpf: use different interpreter depending on required stack size")
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Alexei Starovoitov <ast@fb.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial fix to spelling mistake in netdev_err message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Grzeschik says:
====================
arcnet: Collection of latest features
Here we sum up the latest features to improve the arcnet framework. One
patch is used to get feedback from the transfer queue about failed xfers
by adding the err_skb message queue. Beside that we improve the
backplane status that can be read by the PCI-based cards and offer that
status via an extra sysfs attribute. In the last patch we add another
card type PCIFB2.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We add support for the PCIFB2 card from EAE.
Beside other cards, this card has the backplane mode enabled by default.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
We read the backplane mode of each subcard from bits 2 and 3 of the misc
register.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
We add the sysfs interface the read back the backplane
status of the interface.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to track the status of our queued packages. This way the driving
process knows if failed packages need to be retransmitted. For this
purpose we queue the transferred/failed packages back into the err_skb
message queue added with some status information.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Grzeschik says:
====================
arcnet: Collection of latest fixes
Here we sum up the recent fixes I collected on the way to use and
stabilise the framework. Part of it is an possible deadlock that we
prevent as well to fix the calculation of the dev_id that can be setup
by an rotary encoder. Beside that we added an trivial spelling patch and
fix some wrong and missing assignments that improves the code footprint.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We add the pdev data to the pci devices netdev structure. This way
the interface get consistent device names in the userspace (udev).
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dev_id was miscalculated. Only the two bits 4-5 are relevant for the
MA1 card. PCIARC1 and PCIFB2 use the four bits 4-7 for id selection.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Lendacky says:
====================
amd-xgbe: AMD XGBE driver updates 2016-06-28
The following updates and fixes are included in this driver update series:
- Simplify mailbox interface code
- Fix SFP supported and advertising settings
- Fix PTP initialization register usage
- Insure there is timestamp skb present before using it
- Add a timeout to timestamp register updates
- Handle return code from software reset function
- Some fixes for handling 2.5Gbps rates
- Limit I2C error messages
- Fix non-DMA interrupt handling through tasklet usage
- Add NUMA affinity support for memory allocations
- Add NUMA affinity support for interrupts
- Prepare for more fine-grained cache coherency controls
- Simplify setting the DMA burst length programming
- Performance improvements
This patch series is based on net-next.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to change some general performance settings and to provide
some performance settings based on the device that is probed.
This includes:
- Setting the maximum read/write outstanding request limit
- Reducing the AXI interface burst length size
- Selectively setting the Tx and Rx descriptor pre-fetch threshold
- Selectively setting additional cache coherency controls
Tested and verified on all versions of the hardware.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the driver hardcodes the PBLx8 setting. Remove the need for
specifying the PBLx8 setting and automatically calculate based on the
specified PBL value. Since the PBLx8 setting applies to both Tx and Rx
use the same PBL value for both of them.
Also, the driver currently uses a bit field to set the AXI master burst
len setting. Change to the full bit field range and set the burst length
based on the specified value.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In prep for setting fine grained read and write DMA cache coherency
controls, allow specific values to be used to set the cache coherency
registers.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For IRQ affinity, set the affinity hints for the IRQs to be (initially) on
the processors corresponding to the NUMA node of the device.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to perform memory allocations on the node of the device. The
original allocation or the ring structure and Tx/Rx queues allocated all
of the memory at once and then carved it up for each channel and queue.
To best ensure that we get as much memory from the NUMA node as we can,
break the channel and ring allocations into individual allocations.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the device interrupts should function as level interrupts. For
some hardware configurations this requires setting some control bits
so that if the interrupt status has not been cleared the interrupt
should be reissued.
Additionally, when using MSI or MSI-X interrupts, run the interrupt
service routine as a tasklet so that the re-issuance of the interrupt
is handled properly.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When I2C communication fails, it tends to always fail. Rather than
continuously issue an error message (once per second in most cases),
change the message to be issued just once.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver has some missing functionality when operating in the mode that
supports 2.5GbE. Fix the driver to fully recognize and support this speed.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the function that performs a software reset of the hardware
provides a return code. During driver probe check this return code and
exit with an error if the software reset fails.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Just to be on the safe side, should the update of the timestamp registers
not complete, issue a warning rather than looping forever waiting for the
update to complete.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Spurious Tx timestamp interrupts can cause an oops in the Tx timestamp
processing function if a Tx timestamp skb is NULL. Add a check to insure
a Tx timestamp skb is present before attempting to use it.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During PTP initialization, the Timestamp Control register should be
cleared and not the Tx Configuration register. While this typo causes
the wrong register to be cleared, the default value of each register and
and the fact that the Tx Configuration register is programmed afterwards
doesn't result in a bug, hence only fixing in net-next.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using SFPs, the supported and advertised settings should be initially
based on the SFP that has been detected. The code currently indicates the
overall support of the device as opposed to what the SFP is capable of.
Update the code to change the supported link modes, auto-negotiation, etc.
to be based on the installed SFP.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify and centralize the mailbox command rate change interface by
having a single function perform the writes to the mailbox registers
to issue the request.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
My static checker complains that ofdpa_neigh_del() can sometimes free
"found". It just makes sense to use it first before deleting it.
Fixes: ecf244f753 ("rocker: fix maybe-uninitialized warning")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The newest devices need a longer time to reset because of
their more complex hardware. Wait 5ms after device reset.
Consolidate all the places that reset the device in the
PCIe transport to avoid future bugs.
While at it, unify the flow to use set_bit instead of full
write as requested by the hardware designers.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
iwl_pcie_apm_init can fail so make sure that the caller
takes the status into account.
Also, ensure that the error that iwl_pcie_apm_init can emit
will appear in the kernel log by default.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When a station that's not associated sends a data frame (e.g. an NDP)
hostapd will respond with a disassoc frame, telling it that it's not
associated. The station might also not be authenticated, in which case
there will not be a station entry for it, and as a result we need to
accept such frames without a station.
Fixes: 3ee0f0e23e ("iwlwifi: mvm: fix DQA AP mode station assumption")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we get a non-STA frame to transmit in client mode, we try to use
the IWL_MVM_DQA_BSS_CLIENT_QUEUE queue (queue #4). However, at this
point, the queue might not be allocated at all, causing warnings. The
scenario on which this happened was a race condition between mac80211
and our queue allocation work:
* mac80211 sends auth
* we stop mac80211 queues to allocate a hw queue
* authentication is aborted
* we allocate HW queue and start mac80211 queues
* mac80211 removes station
* mac80211 hands us the auth frame from the pending queue
At this point, since mac80211 has already removed the station, we try
to transmit the frame through this special non-station case on queue
4 anyway.
In order to really use it properly, we'd have to again go through the
hw queue allocation work, and attach it to a station, etc. In this
case that isn't possible (there's no station anymore), but if this
special case were needed, then we'd have to do it this way.
However, the special case is documented to exist for TDLS, but can't
trigger there because the TDLS setup frames etc. are normal to-DS
frames going to the peer through the AP. Testing also confirms that
this code path isn't triggered in TDLS.
Therefore, remove the code path to avoid using an unused queue. The
erroneous frame described above will still be transmitted on the AUX
queue, but arguably that's a mac80211 problem, which will eventually
be fixed by moving everything there to TXQs.
Fixes: e3118ad74d ("iwlwifi: mvm: support tdls in dqa mode")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we get large sends on non-QoS association, we had a
bug that mangled the SNAP header. Fix that.
Fixes: a6d5e32f24 ("iwlwifi: mvm: send large SKBs to the transport")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When going into suspend, the HW configuration for MSI-X will
likely be lost. As a consequence, after waking up, all IRQ
causes will be mapped to interrupt 0, and as a consequence we
don't notice the interrupt because in most cases this is an
interrupt for a queue, and getting it doesn't read the other
cause registers.
Fixes: 2e5d4a8f61 ("iwlwifi: pcie: Add new configuration to enable MSIX")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Getting the TID of a packet before we know it is a QoS data
packet isn't a good idea. Delay the TID retrieval until
we know the packet is a QoS data packet.
Fixes: bb81bb68f4 ("iwlwifi: mvm: add Tx A-MSDU inside A-MPDU")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When in non-DQA mode, mac80211 actually gets a pretty much perfect
idea (in vif->hw_queue/cab_queue) of which queues we're using. But
in DQA mode, this isn't true - nonetheless, we were adding all the
queues, even the ones stations are using, to the queue allocation
bitmap.
Fix this, we should only add the queues we really are using in DQA
mode:
* IWL_MVM_OFFCHANNEL_QUEUE, as we use this in both modes
* mvm->aux_queue, as we use this in both modes - mac80211
never really knows about it but we use it as a cookie
internally, so can't reuse it
* possibly the GCAST queue (cab_queue)
* all the "queues" we told mac80211 about we were using on each
interface (vif->hw_queue), these are entirely virtual in this
mode
Also add back the failure now when we can't allocate any more of
these - now virtual - queues; this was skipped in DQA mode and
would lead to having multiple ACs or even interfaces use the same
queue number in mac80211 (10, since that's the limit), which would
stop far too many queues if stopped.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There may be a difference between the mac80211 vif->cab_queue and
mvmvif->cab_queue, particularly with TVQM. Make the code map this
earlier, instead of first returning the mac80211 one again from
iwl_mvm_get_ctrl_vif_queue().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In the driver, we track which hardware queue is associated with
which mac80211 "hw_queue", in order to be able to stop and wake
it. When moving these bitmaps out of the queue_info structures,
the type of the bitmap was erroneously changed from u32 to u8,
presumably in order to save memory.
Turns out that u32 isn't needed, because the highest queue we
can ever tell mac80211 is always < 16, but a u16 definitely is
needed, queues >=8 do happen.
While at it, throw a BUILD_BUG_ON() into the place where we set
the limit (mvm->first_agg_queue) and a warning when it actually
gets put into the bitmap.
The consequence of this bug is that full HW queues associated
with such a too-high mac80211 number never stop higher layer
queues when full, and thus would simply drop all packets that
couldn't be enqueued to the hardware queue.
Fixes: 34e10860ae ("iwlwifi: mvm: remove references to queue_info in new TX path")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The code was intended to enable IP header checksumming on AMSDUs, but
failed to really do so because the A-MSDU bit was set after all the
checksumming bits, and thus checking for A-MSDU could never be true.
Fix this by setting the A-MSDU bit before the offload bits.
Fixes: 5e6a98dc48 ("iwlwifi: mvm: enable TCP/UDP checksum support for 9000 family")
Reported-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We have tracing for both pre-ICT and ICT interrupts, including all
the data read there. Extend the tracing to MSI-X interrupts.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Martin KaFai Lau says:
====================
bpf: Add syscall lookup support for fd array and htab
This patchset adds BPF_MAP_LOOKUP_ELEM syscall support for
BPF_MAP_TYPE_PROG_ARRAY,
BPF_MAP_TYPE_ARRAY_OF_MAPS and
BPF_MAP_TYPE_HASH_OF_MAPS
====================
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
