Just in case sizes change in the OTP without proper SW
updating, an additional check is inserted when reading OTP
sections to assure no overflows occur.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Some of the maximum values of the parsed external NVM file
in the B-step of the 8000 HW family were updated, so this
updates these values.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The format of the CSR_HW_REV register has changed in 8000
HW family. To keep backwards compatibility, we store the
value of this register as usual in trans->hw_rev, only we
store it in the old format in this variable.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Don't use nvm_hw pointer if it is NULL. Print an error
message if the MAC address isn't valid.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
iwldvm stalls are often blamed on power management. Add an option
to force it all the way off.
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
I've never seen this happen, but it's useful to rule it out.
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Fix NVM channel attributes. Add indoor-only and GO Concurrent
bits. Remove DFS channel bit which is overlapped with radar.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The nvm_file should be loaded by default for SDIO
procucts only. Change the configuration accordingly.
While at it, fix a typo in the device name.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This allows to use the firmware monitor. This capability
uses a lot of contiguous memory (up to 64MB), so make its
usage module parameter dependent.
The driver will try to allocate as much contiguous memory
as possible downgrading its requirements until the
allocation succeeds.
Dump this data into the fw-error dump file when an error
happens.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This can be useful later for parsing since the parsing may
differ based on the device's family / bus.
Also add the human readable version of the firmware.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
MCS32 is currently not supported, so don't
declare support for it.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Use num of scan channels as advertised by fw TLV.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The low-priority scan feature can be useful, e.g. for OBSS
scans (if those are required by the AP); add back support
for it, restoring the maximum out time to the value it was
for low-priority scan before that was removed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Use ksize to get scan command size instead of calculating it, to
avoid nasty bugs.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The current sched scan channel configuration code
configures all the supported channels for scanning.
However, this can result in SYSASSERT in some cases,
when the configured channel is disabled.
Instead, configure only the channels given in the
req struct, and set the channel_count field appropriately.
While on it, change the code to use channel->hw_value
instead of recalculating the channel number.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The power update function looks at all current vifs to determine the power
policy. It doesn't use the current vif. Instead the value was overwritten
and used internally.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This was not used is unlikely to be used, just kill it.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
I forgot to disable the reduced Tx power in a few paths.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
In some cases, we need to force the association to be off in the
MAC_CONTEXT_CMD command we send to the firmware. Instead of having to
hack the vif->bss_conf.assoc value, pass it all the way down the call
chain.
Additionally, for the iwl_mvm_mac_ctxt_add() case, we *always* set
forced_assoc_off to true, so we can remove the hack in the d3 code
that was forcing it to off by hacking the bss_conf.assoc value.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Enabling beacon filtering should be done only after a beacon
has been received. Doing that too early will cause
disconnections.
This has already been fixed, but the fix didn't take care
about the case where the beacon is received after the
association, it waited only for association which is not
enough.
Signed-off-by: Avri Altman <avri.altman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This feature has been causing trouble - disable it for now.
Cc: <stable@vger.kernel.org> [3.13+]
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
There doesn't seem to be a good reason for not enabling the
MAC_FILTER_IN_BEACON flag for P2P client, as we do for station.
This can prevent potential, hard-to-reproduce problems during
association.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Set the MAC_FILTER_IN_BEACON flag in iwl_mvm_mac_ctxt_cmd_sata() also
when forced_assoc_off is set, so it's aligned with when we are not
associated.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
We should not allow diversity when BT Coex needs the second
antenna. Thermal Throttling can also request to stop using
the second antenna. Honour those requests.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This value is being set few lines under in set_cqm_params.
Signed-off-by: Avri Altman <avri.altman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
iwl_mvm_power_update_mac() (more specifically
iwl_mvm_power_iterator()) relies on the phy_ctxt setting to decide
whether the vif is active or not. When unassigning a chanctx, we
should therefore call iwl_mvm_power_update_mac() after setting
phy_chanctx to NULL.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
If DVM or MVM are built-in but LEDS_CLASS isn't then the current
Kconfig will enable LED support and fail the build. Fix this by
making the LED support depend on LEDS_CLASS being built-in or,
if it is modular, only enabling it if iwlwifi also is.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
In the 8000 HW family the register for forcing an NMI has
changed, so this allows to still be able to force an NMI
while taking into account the HW in order to write to the
correct register.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Instead of having two nearly identical functions to send the mac
context commands, use a single way that can handle both the p2p and
!p2p cases.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The firmware needs to know on what channel we run before we
set the association bit in the MAC context. Change a bit the
flow to achieve this.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Some APs (e.g. TP-LINK TL-WA801N) are disabling aggregation (downlink
to station) when U-APSD is enabled, resulting in low throughput.
Add a module parameter to allow disabling U-APSD support in the driver.
Also re-enable U-APSD for -9 firmware since the firmare issues were
fixed in this release.
There are devices that won't support U-APSD even with newer
firmware, so bring the TLV flag back to detect those.
Signed-off-by: Matt Chen <matt.chen@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
New transport need to configure internal memory based on
the data in the (enlarged) alive notification from the
firmware. Add a transport API for this.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
In some situations (see comment) it makes sense to enable both
chains (if available) to get better throughput by having chain
diversity available.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Prevent sched scan while not idle (including during association or in AP
mode) instead of while associated only.
This fixes my previous commit which was incomplete:
commit bd5e4744a6
Author: David Spinadel <david.spinadel@intel.com>
Date: Thu Apr 24 13:15:29 2014 +0300
iwlwifi: mvm: do no sched scan while associated
Currently the FW doesn't support sched scan while associated,
Prevent it.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
tail should be equal to the last valid index, so
decrease it by one.
This error causes in "a gap" in some cases (as well as
some possible out-of-bound write), finally resulting in
ucode assertion.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Fix a bug in nvm_read_section function if size of the section
is a multiple of 2K:
- if the size of the section is *not* multiple of 2K,
then we will have: read(2K) - return 2K ... read(2K) - return 2K
read(2K) - return the rest (in bytes) and exit the while loop.
- else, if the size of the section is a multiple of 2K,
then we have: read(2K) - return 2K read(2K) - return 2K read(2K) -
return 2K read(2K) - return 0 and exit the while with an error.
We should not return an error in the latter case, because it
might well be that the section was completely read.
Also, we try now to read all the sections as this is needed
for new devices.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
setting SKIP_OVER_DTIM when skip_dtim_periods is 0
causes a ucode assert. set the flag only if needed.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When calling IWL_DEBUG_*() dev_dbg() is currently used, and this
could result in the log being ignored no matter the internal
loglevel, since dev_dbg() may get turned on or off based on the
dynamic debug mechanism.
Replace the dev_dbg() with dev_printk() since dynamic printing
is pointless as we use our own debug level mechanism and there
is just a single dev_dbg() call in the code.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
[rephrase commit message a bit]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
CMD_SYNC is really 0 which is confusing:
if (cmd.flags & CMD_SYNC) is always false.
Fix this by simply removing its definition.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
There's an extra newline that shouldn't be there - remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
