It is fallback condition as GPIOLIB seems to be disabled by default.
Better solution is needed, maybe GPIOLIB could be enabled by default?
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make LNA run-time switching possible for PCTV nanoStick T2 290e!
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The vidioc_overlay op needs an unsigned int, not an unsigned int pointer.
So we need a small function that dereferences the unsigned int pointer.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch fixes regression introduced in commit
4af813108b. Missing pointers
to the sensor subdevs are restored along with subdev callback
notifications to a corresponding FIMC instance driver.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fixes following warnings on 64-bit architectures:
m5mols.h: In function 'm5mols_set_ctrl_mode':
m5mols.h:326:15: warning: cast to pointer from integer of different
size [-Wint-to-pointer-cast]
m5mols.h: In function 'm5mols_get_ctrl_mode':
m5mols.h:331:9: warning: cast from pointer to integer of different
size [-Wpointer-to-int-cast]
drivers/media/i2c/m5mols/m5mols_controls.c:466:2: warning: cast
from pointer to integer of different size
Cc: Heungjun Kim <riverful.kim@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make sure the interrupt is freed when driver probing fails.
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: HeungJun Kim <riverful.kim@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There is no need to to dynamically allocate struct video_device
for the M2M devices, so embed it instead in driver's private
data structure as it is done in case of fimc-capture and fimc-lite,
where it solves some bugs on cleanup paths.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This fixes potential invalid pointer de-reference, when
media_entity_cleanup() is called before video device
is unregistered.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This fixes potential invalid pointer de-reference, when
media_entity_cleanup() is called after video_unregister_device,
and video device structure memory is already freed.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Allow to compile-in the FIMC-LITE driver only on Exynos4212,
Exynos4412 and Exynos5250 SoC where the device is available.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
tda1004x doesn't allow firmware loads while it is busy with something
else. Avoid it to happen by locking the I2C bus during firmware transfer.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use managed functions to clean up the error handling code and function
mx2_camera_remove(). Along with the change, a few variables get removed
from struct mx2_camera_dev.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Tested-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is a piece of code becoming dead since commit 2c9ba37 ([media]
V4L: mx2_camera: remove unsupported i.MX27 DMA mode, make EMMA
mandatory). It should have been removed together with the commit.
Remove it now.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Callbacks were set even attach failed. This leads calling
.release() in error case and resulted crash.
Reported-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Callbacks were set even attach failed. This leads calling
.release() in error case and resulted crash.
Reported-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
fe was not set NULL after it was destroyed in tuner attach fail
error case. Due to that it was destroyed again and Kernel oopsed.
Reported-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Refactor firmware download function. It also should fix one bug
coming from usb_control_msg() message buffers. Taking buffers from
the stack for usb_control_msg() is not allowed as it does not work
on all architectures. Allocate buffers using kmalloc().
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It is 4 x RTL2832U + 4 x FC0012 in one PCIe board.
Of course there is a PCIe USB host controller too.
Big thanks for Darryl Bond reporting and testing that!
Reported-by: Darryl Bond <darryl.bond@gmail.com>
Tested-by: Darryl Bond <darryl.bond@gmail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is initial support for the Asus MyCinema U3100Mini Plus. The driver
in its current form gets detected and loads properly.
Scanning using dvbscan works without problems, Locking onto a channel
using tzap also works fine. Only playback using tzap -r + mplayer was
tested and was fully functional.
It uses the af9035 USB Bridge chip, with an af9033 demodulator. The tuner
used is the FCI FC2580.
Signed-off-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It is just stub implementation, remove it.
Also add debug for beginning of fe callback.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use of frontend callback is highly hardware design dependent
and whole callback could be optional in many cases. Returning
error by default when callback is not implemented is stupid.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Logically it is better ask hardware to stop streaming before
killing urbs carrying stream. Earlier it was just opposite.
Now code runs:
* submit urbs
* start streaming
** streaming ongoing **
* stop streaming
* kill urbs
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
I think it is better name. At that phase renaming is quite painless
as module is not yet merged to mainline Kernel.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently there is LNA behind cxd2820r demodulator GPIO. Use
Kernel GPIO interface to access those GPIOs.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Demodulator cannot perform statistic IOCTLs when it is not tuned.
Return -EAGAIN in such case.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert a nonnegative error return code to a negative one, as returned
elsewhere in the function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
[laurent.pinchart@ideasonboard.com Replaced EBUSY with ENODEV]
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
At commit 07d106d0, Linus pointed out that ENOIOCTLCMD should be
translated as ENOTTY to user mode.
Signed-off-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Also change location of other RTL2832 reference design ID 0bda:2838.
I just like to see reference design IDs at the first IDs in the list.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert the struct i2c_msg initialization to C99 format. This makes
maintaining and editing the code simpler. Also helps once other fields
like transferred are added in future.
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert the struct i2c_msg initialization to C99 format. This makes
maintaining and editing the code simpler. Also helps once other fields
like transferred are added in future.
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert the struct i2c_msg initialization to C99 format. This makes
maintaining and editing the code simpler. Also helps once other fields
like transferred are added in future.
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert the struct i2c_msg initialization to C99 format. This makes
maintaining and editing the code simpler. Also helps once other fields
like transferred are added in future.
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert the struct i2c_msg initialization to C99 format. This makes
maintaining and editing the code simpler. Also helps once other fields
like transferred are added in future.
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert the struct i2c_msg initialization to C99 format. This makes
maintaining and editing the code simpler. Also helps once other fields
like transferred are added in future.
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This replaces BUG_ON() calls with WARN_ON(), and returns
EINVAL if some parameter is NULL, as suggested by Jonathan and Mauro.
The BUG_ON() call is too drastic to be used in this case.
See the full discussion here:
http://www.spinics.net/lists/linux-media/msg52462.html
Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This function returns an integer and it's mandatory
to check the return code.
Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The Terratec Cinergy T PCIe Dual is based on the CX23885, and uses
MT2063, DRX-3913k and DRX-3916k chips, so select the relevant drivers.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
