Here are some small tty and serial driver fixes for some reported
problems:
- fsl_uart driver bugfixes
- sh-sci serial driver bugfixes
- renesas serial driver DT binding bugfixes
- 8250 DMA bugfix
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iGwEABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZDFTtg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynImACXZSsiSzuMqAoEisjLfcb7bPovvQCfd5FntU3K
h6JE0Y44gi6WS9iWYHU=
=jDa+
-----END PGP SIGNATURE-----
Merge tag 'tty-6.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver fixes from Greg KH:
"Here are some small tty and serial driver fixes for some reported
problems:
- fsl_uart driver bugfixes
- sh-sci serial driver bugfixes
- renesas serial driver DT binding bugfixes
- 8250 DMA bugfix
All of these have been in linux-next for a while with no reported
problems"
* tag 'tty-6.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: serial: sh-sci: Fix Rx on RZ/G2L SCI
tty: serial: fsl_lpuart: fix crash in lpuart_uport_is_active
tty: serial: fsl_lpuart: avoid checking for transfer complete when UARTCTRL_SBK is asserted in lpuart32_tx_empty
serial: 8250: Prevent starting up DMA Rx on THRI interrupt
dt-bindings: serial: renesas,scif: Fix 4th IRQ for 4-IRQ SCIFs
tty: serial: sh-sci: Fix transmit end interrupt handler
SCI IP on RZ/G2L alike SoCs do not need regshift compared to other SCI
IPs on the SH platform. Currently, it does regshift and configuring Rx
wrongly. Drop adding regshift for RZ/G2L alike SoCs.
Fixes: dfc80387ae ("serial: sh-sci: Compute the regshift value for SCI ports")
Cc: stable@vger.kernel.org
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230321114753.75038-3-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For serdev framework, tty->dev is a NULL pointer, lpuart_uport_is_active
calling device_may_wakeup() may cause kernel NULL pointer crash, so here
add the NULL pointer check before using it.
Fixes: 4f5cb8c5e9 ("tty: serial: fsl_lpuart: enable wakeup source for lpuart")
Cc: stable <stable@kernel.org>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20230323110923.24581-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to LPUART RM, Transmission Complete Flag becomes 0 if queuing
a break character by writing 1 to CTRL[SBK], so here need to avoid
checking for transmission complete when UARTCTRL_SBK is asserted,
otherwise the lpuart32_tx_empty may never get TIOCSER_TEMT.
Commit 2411fd94ceaa("tty: serial: fsl_lpuart: skip waiting for
transmission complete when UARTCTRL_SBK is asserted") only fix it in
lpuart32_set_termios(), here also fix it in lpuart32_tx_empty().
Fixes: 380c966c09 ("tty: serial: fsl_lpuart: add 32-bit register interface support")
Cc: stable <stable@kernel.org>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20230323054415.20363-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hans de Goede reported Bluetooth adapters (HCIs) connected over an UART
connection failed due corrupted Rx payload. The problem was narrowed
down to DMA Rx starting on UART_IIR_THRI interrupt. The problem occurs
despite LSR having DR bit set, which is precondition for attempting to
start DMA Rx in the first place.
From a debug patch:
[x.807834] 8250irq: iir=cc lsr+saved=60 received=0/15 ier=0f dma_t/rx/err=0/0/0
[x.808676] 8250irq: iir=c2 lsr+saved=61 received=0/0 ier=0f dma_t/rx/err=0/0/0
[x.808776] 8250irq: iir=cc lsr+saved=60 received=1/12 ier=0d dma_t/rx/err=0/1/0
[x.808870] Bluetooth: hci0: Frame reassembly failed (-84)
In the debug snippet, received field indicates 1 byte was transferred
over DMA and 12 bytes after that with the non-DMA Rx. The sole byte DMA
handled was corrupted (gets zeroed) which leads to the HCI failure.
This problem became apparent after commit e8ffbb71f7 ("serial: 8250:
use THRE & __stop_tx also with DMA") changed Tx stop behavior. Tx stop
is now triggered from a THRI interrupt.
Despite that this problem looks like a HW bug, this fix is not adding
UART_BUG_xx flag to the driver beucase it seems useful in general to
avoid starting DMA when there are only a few bytes to transfer.
Skipping DMA for small transfers avoids the extra overhead DMA incurs.
Thus, don't setup DMA Rx on UART_IIR_THRI but leave it to a subsequent
interrupt which has Rx a related IIR value.
By returning false from handle_rx_dma(), the DMA vs non-DMA decision is
postponed until either UART_IIR_RDI (FIFO threshold worth of bytes
awaiting) or UART_IIR_TIMEOUT (inter-character timeout) triggers at a
later time which allows better to discern whether the number of bytes
warrants starting DMA or not.
Reported-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Fixes: e8ffbb71f7 ("serial: 8250: use THRE & __stop_tx also with DMA")
Cc: stable@vger.kernel.org
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230317103034.12881-1-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The fourth interrupt on SCI port is transmit end interrupt compared to
the break interrupt on other port types. So, shuffle the interrupts to fix
the transmit end interrupt handler.
Fixes: e1d0be6161 ("sh-sci: Add h8300 SCI")
Cc: stable <stable@kernel.org>
Suggested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230317150403.154094-1-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRTLbB6QfY48x44uB6AXGG7T9hjvgUCZB2KdAAKCRCAXGG7T9hj
vseqAP9OlHO4qqfTWlSmYSPisfWwDT6CM7+K+4vWpMXFh3ZGuAEAhER0mNM1ikoB
ZF7Ash778XPt2CaapQLsHtFZqJUn5gw=
=ouzt
-----END PGP SIGNATURE-----
Merge tag 'for-linus-6.3-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
- fix build warning
- avoid concurrent accesses to the Xen PV console ring page
* tag 'for-linus-6.3-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
x86/PVH: avoid 32-bit build warning when obtaining VGA console info
hvc/xen: prevent concurrent accesses to the shared ring
The hvc machinery registers both a console and a tty device based on
the hv ops provided by the specific implementation. Those two
interfaces however have different locks, and there's no single locks
that's shared between the tty and the console implementations, hence
the driver needs to protect itself against concurrent accesses.
Otherwise concurrent calls using the split interfaces are likely to
corrupt the ring indexes, leaving the console unusable.
Introduce a lock to xencons_info to serialize accesses to the shared
ring. This is only required when using the shared memory console,
concurrent accesses to the hypercall based console implementation are
not an issue.
Note the conditional logic in domU_read_console() is slightly modified
so the notify_daemon() call can be done outside of the locked region:
it's an hypercall and there's no need for it to be done with the lock
held.
Fixes: b536b4b962 ('xen: use the hvc console infrastructure for Xen console')
Signed-off-by: Roger Pau Monné <roger.pau@citrix.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/20221130150919.13935-1-roger.pau@citrix.com
Signed-off-by: Juergen Gross <jgross@suse.com>
We need the mainline fixes in this branch for testing and other
subsystem changes to be based properly on.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are some small tty and serial driver fixes for 6.3-rc3 to resolve
some reported issues.
They include:
- 8250 driver Kconfig issue pointed out by you that showed up in -rc1
- qcom-geni serial driver fixes
- various 8250 driver fixes for reported problems
- fsl_lpuart driver fixes
- serdev fix for regression in -rc1
- vt.c bugfix
All have been in linux-next for over a week with no reported problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZBcinQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynIYACgjP49Xy1N6hDLZJgKxvnPLmvnhY4AoKM8CkHI
zbWudA1fBqsYLFtxNKaQ
=/Ond
-----END PGP SIGNATURE-----
Merge tag 'tty-6.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver fixes from Greg KH:
"Here are some small tty and serial driver fixes for 6.3-rc3 to resolve
some reported issues.
They include:
- 8250 driver Kconfig issue pointed out by you that showed up in -rc1
- qcom-geni serial driver fixes
- various 8250 driver fixes for reported problems
- fsl_lpuart driver fixes
- serdev fix for regression in -rc1
- vt.c bugfix
All have been in linux-next for over a week with no reported problems"
* tag 'tty-6.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: vt: protect KD_FONT_OP_GET_TALL from unbound access
serial: qcom-geni: drop bogus uart_write_wakeup()
serial: qcom-geni: fix mapping of empty DMA buffer
serial: qcom-geni: fix DMA mapping leak on shutdown
serial: qcom-geni: fix console shutdown hang
serdev: Set fwnode for serdev devices
tty: serial: fsl_lpuart: fix race on RX DMA shutdown
serial: 8250_pci1xxxx: Disable SERIAL_8250_PCI1XXXX config by default
serial: 8250_fsl: fix handle_irq locking
serial: 8250_em: Fix UART port type
serial: 8250: ASPEED_VUART: select REGMAP instead of depending on it
tty: serial: fsl_lpuart: skip waiting for transmission complete when UARTCTRL_SBK is asserted
Revert "tty: serial: fsl_lpuart: adjust SERIAL_FSL_LPUART_CONSOLE config dependency"
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/lkml/20221118224540.619276-572-uwe@kleine-koenig.org
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
In ioctl(KD_FONT_OP_GET_TALL), userland tells through op->height which
vpitch should be used to copy over the font. In con_font_get, we were
not checking that it is within the maximum height value, and thus
userland could make the vc->vc_sw->con_font_get(vc, &font, vpitch);
call possibly overflow the allocated max_font_size bytes, and the
copy_to_user(op->data, font.data, c) call possibly read out of that
allocated buffer.
By checking vpitch against max_font_height, the max_font_size buffer
will always be large enough for the vc->vc_sw->con_font_get(vc, &font,
vpitch) call (since we already prevent loading a font larger than that),
and c = (font.width+7)/8 * vpitch * font.charcount will always remain
below max_font_size.
Fixes: 24d69384bc ("VT: Add KD_FONT_OP_SET/GET_TALL operations")
Reported-by: syzbot+3af17071816b61e807ed@syzkaller.appspotmail.com
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230306094921.tik5ewne4ft6mfpo@begin
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ipwireless' Kconfig entry is currently sitting in char/pcmcia. But
the driver is in tty/. So move the entry to tty/ too.
First, it makes sense to have the entry along the driver. Second, whole
char/pcmcia is about to pass away.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: David Sterba <dsterba@suse.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: David Sterba <dsterba@suse.com>
Link: https://lore.kernel.org/r/20230222092302.6348-1-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drop the bogus uart_write_wakeup() from when setting up a new DMA
transfer, which does not free up any more space in the ring buffer.
Any pending writers will be woken up when the transfer completes.
Cc: stable <stable@kernel.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Tested-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Tested-by: Andrew Halaney <ahalaney@redhat.com> # sa8540p-ride
Link: https://lore.kernel.org/r/20230307164405.14218-5-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure that there is data in the ring buffer before trying to set up
a zero-length DMA transfer.
This specifically fixes the following warning when unmapping the empty
buffer on the sc8280xp-crd:
WARNING: CPU: 0 PID: 138 at drivers/iommu/dma-iommu.c:1046 iommu_dma_unmap_page+0xbc/0xd8
...
Call trace:
iommu_dma_unmap_page+0xbc/0xd8
dma_unmap_page_attrs+0x30/0x1c8
geni_se_tx_dma_unprep+0x28/0x38
qcom_geni_serial_isr+0x358/0x75c
Fixes: 2aaa43c707 ("tty: serial: qcom-geni-serial: add support for serial engine DMA")
Cc: stable <stable@kernel.org>
Cc: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Tested-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Tested-by: Andrew Halaney <ahalaney@redhat.com> # sa8540p-ride
Link: https://lore.kernel.org/r/20230307164405.14218-4-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix what appears to be a copy-paste error that can lead to a leaked DMA
mapping on close() and failure to restart TX after the port is reopened.
Note that rx_dma_addr is generally NULL when
qcom_geni_serial_stop_tx_dma() is called as part of shutdown() (but
tx_dma_addr need not be).
Fixes: 2aaa43c707 ("tty: serial: qcom-geni-serial: add support for serial engine DMA")
Cc: stable <stable@kernel.org>
Cc: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Tested-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Tested-by: Andrew Halaney <ahalaney@redhat.com> # sa8540p-ride
Link: https://lore.kernel.org/r/20230307164405.14218-3-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A recent commit added back the calls top stop tx and rx to shutdown()
which had previously been removed by commit e83766334f ("tty: serial:
qcom_geni_serial: No need to stop tx/rx on UART shutdown") in order to
be able to use kgdb after stopping the getty.
Not only did this again break kgdb, but it also broke serial consoles
more generally by hanging TX when stopping the getty during reboot.
The underlying problem has been there since the driver was first merged
and fixing it is going to be a bit involved so simply stop calling the
broken stop functions during shutdown for consoles for now.
Fixes: d8aca2f968 ("tty: serial: qcom-geni-serial: stop operations in progress at shutdown")
Cc: stable <stable@kernel.org>
Cc: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Tested-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Tested-by: Andrew Halaney <ahalaney@redhat.com> # sa8540p-ride
Link: https://lore.kernel.org/r/20230307164405.14218-2-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
From time to time DMA completion can come in the middle of DMA shutdown:
<process ctx>: <IRQ>:
lpuart32_shutdown()
lpuart_dma_shutdown()
del_timer_sync()
lpuart_dma_rx_complete()
lpuart_copy_rx_to_tty()
mod_timer()
lpuart_dma_rx_free()
When the timer fires a bit later, sport->dma_rx_desc is NULL:
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000004
pc : lpuart_copy_rx_to_tty+0xcc/0x5bc
lr : lpuart_timer_func+0x1c/0x2c
Call trace:
lpuart_copy_rx_to_tty
lpuart_timer_func
call_timer_fn
__run_timers.part.0
run_timer_softirq
__do_softirq
__irq_exit_rcu
irq_exit
handle_domain_irq
gic_handle_irq
call_on_irq_stack
do_interrupt_handler
...
To fix this fold del_timer_sync() into lpuart_dma_rx_free() after
dmaengine_terminate_sync() to make sure timer will not be re-started in
lpuart_copy_rx_to_tty() <= lpuart_dma_rx_complete().
Fixes: 4a8588a1cf ("serial: fsl_lpuart: delete timer on shutdown")
Cc: stable <stable@kernel.org>
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Link: https://lore.kernel.org/r/20230309134302.74940-2-alexander.sverdlin@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 8250 handle_irq callback is not just called from the interrupt
handler but also from a timer callback when polling (e.g. for ports
without an interrupt line). Consequently the callback must explicitly
disable interrupts to avoid a potential deadlock with another interrupt
in polled mode.
Fix up the two paths in the freescale callback that failed to re-enable
interrupts when polling.
Fixes: 853a9ae29e ("serial: 8250: fix handle_irq locking")
Cc: stable@vger.kernel.org # 5.13
Reported-by: Dan Carpenter <error27@gmail.com>
Link: https://lore.kernel.org/r/Y/xYzqp4ogmOF5t0@kili
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230227085046.24282-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As per HW manual for EMEV2 "R19UH0040EJ0400 Rev.4.00", the UART
IP found on EMMA mobile SoC is Register-compatible with the
general-purpose 16750 UART chip. Fix UART port type as 16750 and
enable 64-bytes fifo support.
Fixes: 22886ee968 ("serial8250-em: Emma Mobile UART driver V2")
Cc: stable@vger.kernel.org
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230227114152.22265-2-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
REGMAP is a hidden (not user visible) symbol. Users cannot set it
directly thru "make *config", so drivers should select it instead of
depending on it if they need it.
Consistently using "select" or "depends on" can also help reduce
Kconfig circular dependency issues.
Therefore, change the use of "depends on REGMAP" to "select REGMAP".
Fixes: 8d310c9107 ("drivers/tty/serial/8250: Make Aspeed VUART SIRQ polarity configurable")
Cc: stable <stable@kernel.org>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Oskar Senft <osk@google.com>
Cc: linux-serial@vger.kernel.org
Link: https://lore.kernel.org/r/20230226053953.4681-9-rdunlap@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to LPUART RM, Transmission Complete Flag becomes 0 if queuing
a break character by writing 1 to CTRL[SBK], so here need to skip
waiting for transmission complete when UARTCTRL_SBK is asserted,
otherwise the kernel may stuck here.
And actually set_termios() adds transmission completion waiting to avoid
data loss or data breakage when changing the baud rate, but we don't
need to worry about this when queuing break characters.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20230223093941.31790-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 5779a072c2.
This results in a link error of
ld: drivers/tty/serial/earlycon.o: in function `parse_options':
drivers/tty/serial/earlycon.c:99: undefined reference to `uart_parse_earlycon'
When the config is in this state
CONFIG_SERIAL_CORE=m
CONFIG_SERIAL_CORE_CONSOLE=y
CONFIG_SERIAL_EARLYCON=y
CONFIG_SERIAL_FSL_LPUART=m
CONFIG_SERIAL_FSL_LPUART_CONSOLE=y
Fixes: 5779a072c2 ("tty: serial: fsl_lpuart: adjust SERIAL_FSL_LPUART_CONSOLE config dependency")
Cc: stable <stable@kernel.org>
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230226173846.236691-1-trix@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 226fae124b ("vc_screen: move load of struct vc_data pointer in
vcs_read() to avoid UAF") moved the call to vcs_vc() into the loop.
While doing this it also moved the unconditional assignment of
ret = -ENXIO;
This unconditional assignment was valid outside the loop but within it
it clobbers the actual value of ret.
To avoid this only assign "ret = -ENXIO" when actually needed.
[ Also, the 'goto unlock_out" needs to be just a "break", so that it
does the right thing when it exits on later iterations when partial
success has happened - Linus ]
Reported-by: Storm Dragon <stormdragon2976@gmail.com>
Link: https://lore.kernel.org/lkml/Y%2FKS6vdql2pIsCiI@hotmail.com/
Fixes: 226fae124b ("vc_screen: move load of struct vc_data pointer in vcs_read() to avoid UAF")
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Link: https://lore.kernel.org/lkml/64981d94-d00c-4b31-9063-43ad0a384bde@t-8ch.de/
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Restore the vcs_size() handling in vcs_read() to what
it had been in previous version.
Fixes: 226fae124b ("vc_screen: move load of struct vc_data pointer in vcs_read() to avoid UAF")
Suggested-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: George Kennedy <george.kennedy@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Here is the large set of driver core changes for 6.3-rc1.
There's a lot of changes this development cycle, most of the work falls
into two different categories:
- fw_devlink fixes and updates. This has gone through numerous review
cycles and lots of review and testing by lots of different devices.
Hopefully all should be good now, and Saravana will be keeping a
watch for any potential regression on odd embedded systems.
- driver core changes to work to make struct bus_type able to be moved
into read-only memory (i.e. const) The recent work with Rust has
pointed out a number of areas in the driver core where we are
passing around and working with structures that really do not have
to be dynamic at all, and they should be able to be read-only making
things safer overall. This is the contuation of that work (started
last release with kobject changes) in moving struct bus_type to be
constant. We didn't quite make it for this release, but the
remaining patches will be finished up for the release after this
one, but the groundwork has been laid for this effort.
Other than that we have in here:
- debugfs memory leak fixes in some subsystems
- error path cleanups and fixes for some never-able-to-be-hit
codepaths.
- cacheinfo rework and fixes
- Other tiny fixes, full details are in the shortlog
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCY/ipdg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynL3gCgwzbcWu0So3piZyLiJKxsVo9C2EsAn3sZ9gN6
6oeFOjD3JDju3cQsfGgd
=Su6W
-----END PGP SIGNATURE-----
Merge tag 'driver-core-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the large set of driver core changes for 6.3-rc1.
There's a lot of changes this development cycle, most of the work
falls into two different categories:
- fw_devlink fixes and updates. This has gone through numerous review
cycles and lots of review and testing by lots of different devices.
Hopefully all should be good now, and Saravana will be keeping a
watch for any potential regression on odd embedded systems.
- driver core changes to work to make struct bus_type able to be
moved into read-only memory (i.e. const) The recent work with Rust
has pointed out a number of areas in the driver core where we are
passing around and working with structures that really do not have
to be dynamic at all, and they should be able to be read-only
making things safer overall. This is the contuation of that work
(started last release with kobject changes) in moving struct
bus_type to be constant. We didn't quite make it for this release,
but the remaining patches will be finished up for the release after
this one, but the groundwork has been laid for this effort.
Other than that we have in here:
- debugfs memory leak fixes in some subsystems
- error path cleanups and fixes for some never-able-to-be-hit
codepaths.
- cacheinfo rework and fixes
- Other tiny fixes, full details are in the shortlog
All of these have been in linux-next for a while with no reported
problems"
[ Geert Uytterhoeven points out that that last sentence isn't true, and
that there's a pending report that has a fix that is queued up - Linus ]
* tag 'driver-core-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (124 commits)
debugfs: drop inline constant formatting for ERR_PTR(-ERROR)
OPP: fix error checking in opp_migrate_dentry()
debugfs: update comment of debugfs_rename()
i3c: fix device.h kernel-doc warnings
dma-mapping: no need to pass a bus_type into get_arch_dma_ops()
driver core: class: move EXPORT_SYMBOL_GPL() lines to the correct place
Revert "driver core: add error handling for devtmpfs_create_node()"
Revert "devtmpfs: add debug info to handle()"
Revert "devtmpfs: remove return value of devtmpfs_delete_node()"
driver core: cpu: don't hand-override the uevent bus_type callback.
devtmpfs: remove return value of devtmpfs_delete_node()
devtmpfs: add debug info to handle()
driver core: add error handling for devtmpfs_create_node()
driver core: bus: update my copyright notice
driver core: bus: add bus_get_dev_root() function
driver core: bus: constify bus_unregister()
driver core: bus: constify some internal functions
driver core: bus: constify bus_get_kset()
driver core: bus: constify bus_register/unregister_notifier()
driver core: remove private pointer from struct bus_type
...
Here is the big set of serial and tty driver updates for 6.3-rc1.
Once again, Jiri and Ilpo have done a number of core vt and tty/serial
layer cleanups that were much needed and appreciated. Other than that,
it's just a bunch of little tty/serial driver updates:
- qcom-geni-serial driver updates
- liteuart driver updates
- hvcs driver cleanups
- n_gsm updates and additions for new features
- more 8250 device support added
- fpga/dfl update and additions
- imx serial driver updates
- fsl_lpuart updates
- other tiny fixes and updates for serial drivers
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCY/itAw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykJbQCfWv/J4ZElO108iHBU5mJCDagUDBgAnAtLLN6A
SEAnnokGCDtA/BNIXeES
=luRi
-----END PGP SIGNATURE-----
Merge tag 'tty-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial driver updates from Greg KH:
"Here is the big set of serial and tty driver updates for 6.3-rc1.
Once again, Jiri and Ilpo have done a number of core vt and tty/serial
layer cleanups that were much needed and appreciated. Other than that,
it's just a bunch of little tty/serial driver updates:
- qcom-geni-serial driver updates
- liteuart driver updates
- hvcs driver cleanups
- n_gsm updates and additions for new features
- more 8250 device support added
- fpga/dfl update and additions
- imx serial driver updates
- fsl_lpuart updates
- other tiny fixes and updates for serial drivers
All of these have been in linux-next for a while with no reported
problems"
* tag 'tty-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (143 commits)
tty: n_gsm: add keep alive support
serial: imx: remove a redundant check
dt-bindings: serial: snps-dw-apb-uart: add dma & dma-names properties
soc: qcom: geni-se: Move qcom-geni-se.h to linux/soc/qcom/geni-se.h
tty: n_gsm: add TIOCMIWAIT support
tty: n_gsm: add RING/CD control support
tty: n_gsm: mark unusable ioctl structure fields accordingly
serial: imx: get rid of registers shadowing
serial: imx: refine local variables in rxint()
serial: imx: stop using USR2 in FIFO reading loop
serial: imx: remove redundant USR2 read from FIFO reading loop
serial: imx: do not break from FIFO reading loop prematurely
serial: imx: do not sysrq broken chars
serial: imx: work-around for hardware RX flood
serial: imx: factor-out common code to imx_uart_soft_reset()
serial: 8250_pci1xxxx: Add power management functions to quad-uart driver
serial: 8250_pci1xxxx: Add RS485 support to quad-uart driver
serial: 8250_pci1xxxx: Add driver for quad-uart support
serial: 8250_pci: Add serial8250_pci_setup_port definition in 8250_pcilib.c
tty: pcn_uart: fix memory leak with using debugfs_lookup()
...
This is a follow-up to the deprecation of most of the old-style board
files that was merged in linux-6.0, removing them for good.
This branch is almost exclusively dead code removal based on those
annotations. Some device driver removals went through separate subsystem
trees, but the majority is in the same branch, in order to better handle
dependencies between the patches and avoid breaking bisection.
Unfortunately that leads to merge conflicts against other changes in the
subsystem trees, but they should all be trivial to resolve by removing
the files.
See commit 7d0d3fa733 ("Merge tag 'arm-boardfiles-6.0' of
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc") for the
description of which machines were marked unused and are now removed. The
only removals that got postponed are Terastation WXL (mv78xx0) and
Jornada720 (StrongARM1100), which turned out to still have potential
users.
-----BEGIN PGP SIGNATURE-----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=WejQ
-----END PGP SIGNATURE-----
Merge tag 'arm-boardfile-remove-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC boardfile updates from Arnd Bergmann
"Unused boardfile removal for 6.3
This is a follow-up to the deprecation of most of the old-style board
files that was merged in linux-6.0, removing them for good.
This branch is almost exclusively dead code removal based on those
annotations. Some device driver removals went through separate
subsystem trees, but the majority is in the same branch, in order to
better handle dependencies between the patches and avoid breaking
bisection.
Unfortunately that leads to merge conflicts against other changes in
the subsystem trees, but they should all be trivial to resolve by
removing the files.
See commit 7d0d3fa733 ("Merge tag 'arm-boardfiles-6.0' of
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc") for the
description of which machines were marked unused and are now removed.
The only removals that got postponed are Terastation WXL (mv78xx0) and
Jornada720 (StrongARM1100), which turned out to still have potential
users"
* tag 'arm-boardfile-remove-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (91 commits)
mmc: omap: drop TPS65010 dependency
ARM: pxa: restore mfp-pxa320.h
usb: ohci-omap: avoid unused-variable warning
ARM: debug: remove references in DEBUG_UART_8250_SHIFT to removed configs
ARM: s3c: remove obsolete s3c-cpu-freq header
MAINTAINERS: adjust SAMSUNG SOC CLOCK DRIVERS after s3c24xx support removal
MAINTAINERS: update file entries after arm multi-platform rework and mach-pxa removal
ARM: remove CONFIG_UNUSED_BOARD_FILES
mfd: remove htc-pasic3 driver
w1: remove ds1wm driver
usb: remove ohci-tmio driver
fbdev: remove w100fb driver
fbdev: remove tmiofb driver
mmc: remove tmio_mmc driver
mfd: remove ucb1400 support
mfd: remove toshiba tmio drivers
rtc: remove v3020 driver
power: remove pda_power supply driver
ASoC: pxa: remove unused board support
pcmcia: remove unused pxa/sa1100 drivers
...
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapters 5.4.6.3.4 and 5.1.8.1.3 describe the test
command which can be used to test the mux connection between both sides.
Currently, no algorithm is implemented to make use of this command. This
requires that each multiplexed upper layer protocol supervises the
underlying muxer connection to handle possible connection losses.
Introduce ioctl commands and functions to optionally enable keep alive
handling via the test command as described in chapter 5.4.6.3.4. A single
incrementing octet "ka_num" is being used for unique identification of each
single keep alive packet. Retries will use the same "ka_num" value as the
original packet. Retry count and interval are taken from the general
parameters N2 and T2.
Add usage description and basic example for the new ioctl to the n_gsm
documentation.
Note that support for the test command is mandatory and already present in
the muxer implementation since the very first version.
Also note that the previous ioctl structure gsm_config cannot be extended
due to missing checks against zero of the field "unused".
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20230214122737.1976-1-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cpp_check reports
drivers/tty/serial/imx.c:1207:15: style: Condition 'r_bytes>0' is always true [knownConditionTrueFalse]
if (r_bytes > 0) {
r_byte is set to
r_bytes = rx_ring->head - rx_ring->tail;
The head - tail calculation is also done by the earlier check
if (rx_ring->head <= sg_dma_len(sgl) &&
rx_ring->head > rx_ring->tail) {
so r_bytes will always be > 0, so the second check is not needed.
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Iuliana Prodan <iuliana.prodan@nxp.com>
Link: https://lore.kernel.org/r/20230211154550.2130670-1-trix@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move include/linux/qcom-geni-se.h to include/linux/soc/qcom/geni-se.h.
This removes 1 of a few remaining Qualcomm-specific headers into a more
approciate subdirectory under include/.
Signed-off-by: Elliot Berman <quic_eberman@quicinc.com>
Acked-by: Bjorn Andersson <andersson@kernel.org>
Acked-by: Wolfram Sang <wsa@kernel.org> # for I2C
Reviewed-by: Guru Das Srinagesh <quic_gurus@quicinc.com>
Link: https://lore.kernel.org/r/20230203210133.3552796-1-quic_eberman@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for the TIOCMIWAIT ioctl on the virtual ttys. This enables the
user to wait for virtual modem signals like RING.
More work is needed to support also TIOCGICOUNT.
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20230206114606.2133-4-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The status lines ring and carrier detect are used by the modem to signal
incoming calls (RING) or an established connection (CD). This is
implemented as physical lines on a standard RS232 connection. However,
the muxer protocol encodes these status lines as modem bits IC and DV.
These incoming lines are masked by tty driver (see tty_io.c) and cannot be
set by a user application.
Allow setting RING via TIOCM_OUT1 and CD via TIOCM_OUT2 to allow
implementation of a modem or modem emulator.
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20230206114606.2133-3-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Neither registers shadowing is functionally needed as all the registers are
read-write, nor the shadowing makes much sense for speed-up, as most speed
critical reads/writes (of data Rx/Tx registers) are not shadowed anyway.
Moreover, the shadowing code is obviously pure overhead on the write path.
Get rid of the shadowing code and variables due to above considerations.
Signed-off-by: Sergey Organov <sorganov@gmail.com>
Link: https://lore.kernel.org/r/20230201141603.4205-1-sorganov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 'rx' is chip register, similar to 'usr2', so let it be of 'u32' type as
well.
Move 'flg' to be FIFO read loop local as it's not used outside.
Signed-off-by: Sergey Organov <sorganov@gmail.com>
Link: https://lore.kernel.org/r/20230201142700.4346-8-sorganov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The chip provides all the needed bits in the URXD0 register that we read
anyway for data, so get rid of reading USR2 and use only URXD0 bits
instead.
Signed-off-by: Sergey Organov <sorganov@gmail.com>
Link: https://lore.kernel.org/r/20230201142700.4346-7-sorganov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to read USR2 twice at every loop iteration: get rid of the
second read.
Signed-off-by: Sergey Organov <sorganov@gmail.com>
Link: https://lore.kernel.org/r/20230201142700.4346-6-sorganov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no reason to prematurely break out of FIFO reading loop, and it
might cause needless reenters into ISR, so keep reading until FIFO is
empty.
Signed-off-by: Sergey Organov <sorganov@gmail.com>
Link: https://lore.kernel.org/r/20230201142700.4346-5-sorganov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do not call uart_handle_sysrq_char() if we got any receive error along with
the character, as we don't want random junk to be considered a sysrq.
Signed-off-by: Sergey Organov <sorganov@gmail.com>
Link: https://lore.kernel.org/r/20230201142700.4346-4-sorganov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Check if hardware Rx flood is in progress, and issue soft reset to UART to
stop the flood.
A way to reproduce the flood (checked on iMX6SX) is: open iMX UART at 9600
8N1, and from external source send 0xf0 char at 115200 8N1. In about 90% of
cases this starts a flood of "receiving" of 0xff characters by the iMX UART
that is terminated by any activity on RxD line, or could be stopped by
issuing soft reset to the UART (just stop/start of RX does not help). Note
that in essence what we did here is sending isolated start bit about 2.4
times shorter than it is to be if issued on the UART configured baud rate.
There was earlier attempt to fix similar issue in: 'commit
b38cb7d257 ("serial: imx: Disable new features of autobaud detection")',
but apparently it only gets harder to reproduce the issue after that
commit.
Signed-off-by: Sergey Organov <sorganov@gmail.com>
Link: https://lore.kernel.org/r/20230201142700.4346-3-sorganov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We perform soft reset in 2 places, slightly differently for no sufficient
reasons, so move more generic variant to a function, and re-use the code.
Out of 2 repeat counters, 10 and 100, select 10, as the code works at
interrupts disabled, and in practice the reset happens immediately.
Signed-off-by: Sergey Organov <sorganov@gmail.com>
Link: https://lore.kernel.org/r/20230201142700.4346-2-sorganov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pci1xxxx's quad-uart function has the capability to wake up UART
from suspend state. Enable wakeup before entering into suspend and
disable wakeup on resume.
Co-developed-by: Tharun Kumar P <tharunkumar.pasumarthi@microchip.com>
Signed-off-by: Tharun Kumar P <tharunkumar.pasumarthi@microchip.com>
Signed-off-by: Kumaravel Thiagarajan <kumaravel.thiagarajan@microchip.com>
Link: https://lore.kernel.org/r/20230207164814.3104605-5-kumaravel.thiagarajan@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pci1xxxx uart supports RS485 mode of operation in the hardware with
auto-direction control with configurable delay for releasing RTS after
the transmission. This patch adds support for the RS485 mode.
Co-developed-by: Tharun Kumar P <tharunkumar.pasumarthi@microchip.com>
Signed-off-by: Tharun Kumar P <tharunkumar.pasumarthi@microchip.com>
Signed-off-by: Kumaravel Thiagarajan <kumaravel.thiagarajan@microchip.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230207164814.3104605-4-kumaravel.thiagarajan@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pci1xxxx is a PCIe switch with a multi-function endpoint on one of
its downstream ports. Quad-uart is one of the functions in the
multi-function endpoint. This driver loads for the quad-uart and
enumerates single or multiple instances of uart based on the PCIe
subsystem device ID.
Co-developed-by: Tharun Kumar P <tharunkumar.pasumarthi@microchip.com>
Signed-off-by: Tharun Kumar P <tharunkumar.pasumarthi@microchip.com>
Signed-off-by: Kumaravel Thiagarajan <kumaravel.thiagarajan@microchip.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230207164814.3104605-3-kumaravel.thiagarajan@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When calling debugfs_lookup() the result must have dput() called on it,
otherwise the memory will leak over time. To make things simpler, just
call debugfs_lookup_and_remove() instead which handles all of the logic
at once.
Cc: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230202141221.2293012-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Synchronizes hotplug remove with the freeing of the port.
This ensures we have freed all the memory associated with
this port and are not leaking memory.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Link: https://lore.kernel.org/r/20230203155802.404324-6-brking@linux.vnet.ibm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
