On Sun Ultra 5, it happens that the dot clock is not set up properly for
some videomodes. For example, if we set the videomode "r1024x768x60" in
the firmware, Linux would incorrectly set a videomode with refresh rate
180Hz when booting (suprisingly, my LCD monitor can display it, although
display quality is very low).
The reason is this: Older mach64 cards set the divider in the register
VCLK_POST_DIV. The register has four 2-bit fields (the field that is
actually used is specified in the lowest two bits of the register
CLOCK_CNTL). The 2 bits select divider "1, 2, 4, 8". On newer mach64 cards,
there's another bit added - the top four bits of PLL_EXT_CNTL extend the
divider selection, so we have possible dividers "1, 2, 4, 8, 3, 5, 6, 12".
The Linux driver clears the top four bits of PLL_EXT_CNTL and never sets
them, so it can work regardless if the card supports them. However, the
sparc64 firmware may set these extended dividers during boot - and the
mach64 driver detects incorrect dot clock in this case.
This patch makes the driver read the additional divider bit from
PLL_EXT_CNTL and calculate the initial refresh rate properly.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Acked-by: David S. Miller <davem@davemloft.net>
Reviewed-by: Ville Syrjälä <syrjala@sci.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace "fall though" with a proper "fall through" annotation.
This fix is part of the ongoing efforts to enabling
-Wimplicit-fallthrough
Addresses-Coverity-ID: 402013 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
In some setups restoring the BGRT logo is undesirable, allow passing
video=efifb:nobgrt on the kernel commandline to disable it.
Reported-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
OMAPFB_MEMORY_READ ioctl reads pixels from the LCD's memory and copies
them to a userspace buffer. The code has two issues:
- The user provided width and height could be large enough to overflow
the calculations
- The copy_to_user() can copy uninitialized memory to the userspace,
which might contain sensitive kernel information.
Fix these by limiting the width & height parameters, and only copying
the amount of data that we actually received from the LCD.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reported-by: Jann Horn <jannh@google.com>
Cc: stable@vger.kernel.org
Cc: security@kernel.org
Cc: Will Deacon <will.deacon@arm.com>
Cc: Jann Horn <jannh@google.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
- add support for deferred console takeover, when enabled defers
fbcon taking over the console from the dummy console until the
first text is displayed on the console - together with the "quiet"
kernel commandline option this allows fbcon to still be used
together with a smooth graphical bootup (Hans de Goede)
- improve console locking debugging code (Thomas Zimmermann)
- copy the ACPI BGRT boot graphics to the framebuffer when deferred
console takeover support is used in efifb driver (Hans de Goede)
- update udlfb driver - fix lost console when the user unplugs a USB
adapter, fix the screen corruption issue, fix locking and add some
performance optimizations (Mikulas Patocka)
- update pxafb driver - fix using uninitialized memory, switch to
devm_* API, handle initialization errors and add support for
lcd-supply regulator (Daniel Mack)
- add support for boards booted with a DeviceTree in pxa3xx_gcu
driver (Daniel Mack)
- rename omap2 module to omap2fb.ko to avoid conflicts with omap1
driver (Arnd Bergmann)
- enable ACPI-based enumeration for goldfishfb driver (Yu Ning)
- fix goldfishfb driver to make user space Android code use 60 fps
(Christoffer Dall)
- print big fat warning when nomodeset kernel parameter is used in
vgacon driver (Lyude Paul)
- remove VLA usage from fsl-diu-fb driver (Kees Cook)
- misc fixes (Julia Lawall, Geert Uytterhoeven, Fredrik Noring,
Yisheng Xie, Dan Carpenter, Daniel Vetter, Anton Vasilyev, Randy
Dunlap, Gustavo A. R. Silva, Colin Ian King, Fengguang Wu)
- misc cleanups (Roman Kiryanov, Yisheng Xie, Colin Ian King)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=7UE9
-----END PGP SIGNATURE-----
Merge tag 'fbdev-v4.19' of https://github.com/bzolnier/linux
Pull fbdev updates from Bartlomiej Zolnierkiewicz:
"Mostly small fixes and cleanups for fb drivers (the biggest updates
are for udlfb and pxafb drivers). This also adds deferred console
takeover support to the console code and efifb driver.
Summary:
- add support for deferred console takeover, when enabled defers
fbcon taking over the console from the dummy console until the
first text is displayed on the console - together with the "quiet"
kernel commandline option this allows fbcon to still be used
together with a smooth graphical bootup (Hans de Goede)
- improve console locking debugging code (Thomas Zimmermann)
- copy the ACPI BGRT boot graphics to the framebuffer when deferred
console takeover support is used in efifb driver (Hans de Goede)
- update udlfb driver - fix lost console when the user unplugs a USB
adapter, fix the screen corruption issue, fix locking and add some
performance optimizations (Mikulas Patocka)
- update pxafb driver - fix using uninitialized memory, switch to
devm_* API, handle initialization errors and add support for
lcd-supply regulator (Daniel Mack)
- add support for boards booted with a DeviceTree in pxa3xx_gcu
driver (Daniel Mack)
- rename omap2 module to omap2fb.ko to avoid conflicts with omap1
driver (Arnd Bergmann)
- enable ACPI-based enumeration for goldfishfb driver (Yu Ning)
- fix goldfishfb driver to make user space Android code use 60 fps
(Christoffer Dall)
- print big fat warning when nomodeset kernel parameter is used in
vgacon driver (Lyude Paul)
- remove VLA usage from fsl-diu-fb driver (Kees Cook)
- misc fixes (Julia Lawall, Geert Uytterhoeven, Fredrik Noring,
Yisheng Xie, Dan Carpenter, Daniel Vetter, Anton Vasilyev, Randy
Dunlap, Gustavo A. R. Silva, Colin Ian King, Fengguang Wu)
- misc cleanups (Roman Kiryanov, Yisheng Xie, Colin Ian King)"
* tag 'fbdev-v4.19' of https://github.com/bzolnier/linux: (54 commits)
Documentation/fb: corrections for fbcon.txt
fbcon: Do not takeover the console from atomic context
dummycon: Stop exporting dummycon_[un]register_output_notifier
fbcon: Only defer console takeover if the current console driver is the dummycon
fbcon: Only allow FRAMEBUFFER_CONSOLE_DEFERRED_TAKEOVER if fbdev is builtin
fbdev: omap2: omapfb: fix ifnullfree.cocci warnings
fbdev: omap2: omapfb: fix bugon.cocci warnings
fbdev: omap2: omapfb: fix boolreturn.cocci warnings
fb: amifb: fix build warnings when not builtin
fbdev/core: Disable console-lock warnings when fb.lockless_register_fb is set
console: Replace #if 0 with atomic var 'ignore_console_lock_warning'
udlfb: use spin_lock_irq instead of spin_lock_irqsave
udlfb: avoid prefetch
udlfb: optimization - test the backing buffer
udlfb: allow reallocating the framebuffer
udlfb: set line_length in dlfb_ops_set_par
udlfb: handle allocation failure
udlfb: set optimal write delay
udlfb: make a local copy of fb_ops
udlfb: don't switch if we are switching to the same videomode
...
- Remove unused/obsolete code/comments
- New Functionality
- Allow less granular brightness specification for high-res PWMs; pwm_bl
- Align brightness {inc,dec}rements with that perceived by the human-eye; pwm_bl
- Fix-ups
- Prepare for the introduction of -Wimplicit-fall-through; adp8860_bl
- Bug Fixes
- Fix uninitialised variable; pwm_bl
-----BEGIN PGP SIGNATURE-----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=C/pI
-----END PGP SIGNATURE-----
Merge tag 'backlight-next-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight
Pull backlight updates from Lee Jones:
"Core Framework:
- Remove unused/obsolete code/comments
New Functionality:
- Allow less granular brightness specification for high-res PWMs; pwm_bl
- Align brightness {inc,dec}rements with that perceived by the human-eye; pwm_bl
Fix-ups:
- Prepare for the introduction of -Wimplicit-fall-through; adp8860_bl
Bug Fixes:
- Fix uninitialised variable; pwm_bl"
* tag 'backlight-next-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight:
backlight: pwm_bl: Fix uninitialized variable
backlight: adp8860: Mark expected switch fall-through
backlight: Remove obsolete comment for ->state
dt-bindings: pwm-backlight: Move brightness-levels to optional
backlight: pwm_bl: Compute brightness of LED linearly to human eye
dt-bindings: pwm-backlight: Add a num-interpolation-steps property
backlight: pwm_bl: Linear interpolation between brightness-levels
Here is the bit set of char/misc drivers for 4.19-rc1
There is a lot here, much more than normal, seems like everyone is
writing new driver subsystems these days... Anyway, major things here
are:
- new FSI driver subsystem, yet-another-powerpc low-level
hardware bus
- gnss, finally an in-kernel GPS subsystem to try to tame all of
the crazy out-of-tree drivers that have been floating around
for years, combined with some really hacky userspace
implementations. This is only for GNSS receivers, but you
have to start somewhere, and this is great to see.
Other than that, there are new slimbus drivers, new coresight drivers,
new fpga drivers, and loads of DT bindings for all of these and existing
drivers.
Full details of everything is in the shortlog.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCW3g7ew8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykfBgCeOG0RkSI92XVZe0hs/QYFW9kk8JYAnRBf3Qpm
cvW7a+McOoKz/MGmEKsi
=TNfn
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the bit set of char/misc drivers for 4.19-rc1
There is a lot here, much more than normal, seems like everyone is
writing new driver subsystems these days... Anyway, major things here
are:
- new FSI driver subsystem, yet-another-powerpc low-level hardware
bus
- gnss, finally an in-kernel GPS subsystem to try to tame all of the
crazy out-of-tree drivers that have been floating around for years,
combined with some really hacky userspace implementations. This is
only for GNSS receivers, but you have to start somewhere, and this
is great to see.
Other than that, there are new slimbus drivers, new coresight drivers,
new fpga drivers, and loads of DT bindings for all of these and
existing drivers.
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (255 commits)
android: binder: Rate-limit debug and userspace triggered err msgs
fsi: sbefifo: Bump max command length
fsi: scom: Fix NULL dereference
misc: mic: SCIF Fix scif_get_new_port() error handling
misc: cxl: changed asterisk position
genwqe: card_base: Use true and false for boolean values
misc: eeprom: assignment outside the if statement
uio: potential double frees if __uio_register_device() fails
eeprom: idt_89hpesx: clean up an error pointer vs NULL inconsistency
misc: ti-st: Fix memory leak in the error path of probe()
android: binder: Show extra_buffers_size in trace
firmware: vpd: Fix section enabled flag on vpd_section_destroy
platform: goldfish: Retire pdev_bus
goldfish: Use dedicated macros instead of manual bit shifting
goldfish: Add missing includes to goldfish.h
mux: adgs1408: new driver for Analog Devices ADGS1408/1409 mux
dt-bindings: mux: add adi,adgs1408
Drivers: hv: vmbus: Cleanup synic memory free path
Drivers: hv: vmbus: Remove use of slow_virt_to_phys()
Drivers: hv: vmbus: Reset the channel callback in vmbus_onoffer_rescind()
...
-----BEGIN PGP SIGNATURE-----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=ClJZ
-----END PGP SIGNATURE-----
Merge tag 'media/v4.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- new Socionext MN88443x ISDB-S/T demodulator driver: mn88443x
- new sensor drivers: ak7375, ov2680 and rj54n1cb0c
- an old soc-camera sensor driver converted to the V4L2 framework:
mt9v111
- a new Voice-Coil Motor (VCM) driver: dw9807-vcm
- some cleanups at cx25821, removing legacy unused code
- some improvements at ddbridge driver
- new platform driver: vicodec
- some DVB API cleanups, removing ioctls and compat code for old
out-of-tree drivers that were never merged upstream
- improvements at DVB core to support frontents that support both
Satellite and non-satellite delivery systems
- got rid of the unused VIDIOC_RESERVED V4L2 ioctl
- some cleanups/improvements at gl861 ISDB driver
- several improvements on ov772x, ov7670 and ov5640, imx274, ov5645,
and smiapp sensor drivers
- fixes at em28xx to support dual TS devices
- some cleanups at V4L2/VB2 locking logic
- some API improvements at media controller
- some cec core and drivers improvements
- some uvcvideo improvements
- some improvements at platform drivers: stm32-dcmi, rcar-vin, coda,
reneseas-ceu, imx, vsp1, venus, camss
- lots of other cleanups and fixes
* tag 'media/v4.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (406 commits)
Revert "media: vivid: shut up warnings due to a non-trivial logic"
siano: get rid of an unused return code for debugfs register
media: isp: fix a warning about a wrong struct initializer
media: radio-wl1273: fix return code for the polling routine
media: s3c-camif: fix return code for the polling routine
media: saa7164: fix return codes for the polling routine
media: exynos-gsc: fix return code if mutex was interrupted
media: mt9v111: Fix build error with no VIDEO_V4L2_SUBDEV_API
media: xc4000: get rid of uneeded casts
media: drxj: get rid of uneeded casts
media: tuner-xc2028: don't use casts for printing sizes
media: cleanup fall-through comments
media: vivid: shut up warnings due to a non-trivial logic
media: rtl28xxu: be sure that it won't go past the array size
media: mt9v111: avoid going past the buffer
media: vsp1_dl: add a description for cmdpool field
media: sta2x11: add a missing parameter description
media: v4l2-mem2mem: add descriptions to MC fields
media: i2c: fix warning in Aptina MT9V111
media: imx: shut up a false positive warning
...
-----BEGIN PGP SIGNATURE-----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=g9rD
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2018-08-15' of git://anongit.freedesktop.org/drm/drm
Pull drm updates from Dave Airlie:
"This is the main drm pull request for 4.19.
Rob has some new hardware support for new qualcomm hw that I'll send
along separately. This has the display part of it, the remaining pull
is for the acceleration engine.
This also contains a wound-wait/wait-die mutex rework, Peter has acked
it for merging via my tree.
Otherwise mostly the usual level of activity. Summary:
core:
- Wound-wait/wait-die mutex rework
- Add writeback connector type
- Add "content type" property for HDMI
- Move GEM bo to drm_framebuffer
- Initial gpu scheduler documentation
- GPU scheduler fixes for dying processes
- Console deferred fbcon takeover support
- Displayport support for CEC tunneling over AUX
panel:
- otm8009a panel driver fixes
- Innolux TV123WAM and G070Y2-L01 panel driver
- Ilitek ILI9881c panel driver
- Rocktech RK070ER9427 LCD
- EDT ETM0700G0EDH6 and EDT ETM0700G0BDH6
- DLC DLC0700YZG-1
- BOE HV070WSA-100
- newhaven, nhd-4.3-480272ef-atxl LCD
- DataImage SCF0700C48GGU18
- Sharp LQ035Q7DB03
- p079zca: Refactor to support multiple panels
tinydrm:
- ILI9341 display panel
New driver:
- vkms - virtual kms driver to testing.
i915:
- Icelake:
Display enablement
DSI support
IRQ support
Powerwell support
- GPU reset fixes and improvements
- Full ppgtt support refactoring
- PSR fixes and improvements
- Execlist improvments
- GuC related fixes
amdgpu:
- Initial amdgpu documentation
- JPEG engine support on VCN
- CIK uses powerplay by default
- Move to using core PCIE functionality for gens/lanes
- DC/Powerplay interface rework
- Stutter mode support for RV
- Vega12 Powerplay updates
- GFXOFF fixes
- GPUVM fault debugging
- Vega12 GFXOFF
- DC improvements
- DC i2c/aux changes
- UVD 7.2 fixes
- Powerplay fixes for Polaris12, CZ/ST
- command submission bo_list fixes
amdkfd:
- Raven support
- Power management fixes
udl:
- Cleanups and fixes
nouveau:
- misc fixes and cleanups.
msm:
- DPU1 support display controller in sdm845
- GPU coredump support.
vmwgfx:
- Atomic modesetting validation fixes
- Support for multisample surfaces
armada:
- Atomic modesetting support completed.
exynos:
- IPPv2 fixes
- Move g2d to component framework
- Suspend/resume support cleanups
- Driver cleanups
imx:
- CSI configuration improvements
- Driver cleanups
- Use atomic suspend/resume helpers
- ipu-v3 V4L2 XRGB32/XBGR32 support
pl111:
- Add Nomadik LCDC variant
v3d:
- GPU scheduler jobs management
sun4i:
- R40 display engine support
- TCON TOP driver
mediatek:
- MT2712 SoC support
rockchip:
- vop fixes
omapdrm:
- Workaround for DRA7 errata i932
- Fix mm_list locking
mali-dp:
- Writeback implementation
PM improvements
- Internal error reporting debugfs
tilcdc:
- Single fix for deferred probing
hdlcd:
- Teardown fixes
tda998x:
- Converted to a bridge driver.
etnaviv:
- Misc fixes"
* tag 'drm-next-2018-08-15' of git://anongit.freedesktop.org/drm/drm: (1506 commits)
drm/amdgpu/sriov: give 8s for recover vram under RUNTIME
drm/scheduler: fix param documentation
drm/i2c: tda998x: correct PLL divider calculation
drm/i2c: tda998x: get rid of private fill_modes function
drm/i2c: tda998x: move mode_valid() to bridge
drm/i2c: tda998x: register bridge outside of component helper
drm/i2c: tda998x: cleanup from previous changes
drm/i2c: tda998x: allocate tda998x_priv inside tda998x_create()
drm/i2c: tda998x: convert to bridge driver
drm/scheduler: fix timeout worker setup for out of order job completions
drm/amd/display: display connected to dp-1 does not light up
drm/amd/display: update clk for various HDMI color depths
drm/amd/display: program display clock on cache match
drm/amd/display: Add NULL check for enabling dp ss
drm/amd/display: add vbios table check for enabling dp ss
drm/amd/display: Don't share clk source between DP and HDMI
drm/amd/display: Fix DP HBR2 Eye Diagram Pattern on Carrizo
drm/amd/display: Use calculated disp_clk_khz value for dce110
drm/amd/display: Implement custom degamma lut on dcn
drm/amd/display: Destroy aux_engines only once
...
Taking over the console involves allocating mem with GFP_KERNEL, talking
to drm drivers, etc. So this should not be done from an atomic context.
But the console-output trigger deferred console takeover may happen from an
atomic context, which leads to "BUG: sleeping function called from invalid
context" errors.
This commit fixes these errors by doing the deferred takeover from a
workqueue.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[b.zolnierkie: remove unused variable]
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Now that we only allow FRAMEBUFFER_CONSOLE_DEFERRED_TAKEOVER when
fbdev+fbcon are builtin exporting these is no longer necessary.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
We rely on dummycon's output notifier mechanism to defer the takeover.
If say vgacon is the current console driver then dummycon will never get
used so its output notifier will also never get called and fbcon never
takes over. This commit fixes this by only deferring the console takeover
if the current console driver is the dummycon driver.
This commit also moves the entirety of fbcon_start under the console_lock,
since the conswitchp which fbcon_start now checks is protected by it.
This commit also inlines fbcon_register_output_notifier, since we now
need a #ifdef CONFIG_FRAMEBUFFER_CONSOLE_DEFERRED_TAKEOVER in fbcon_start
anyways because of the write access to the deferred_takeover variable,
this has the added advantage that it puts the
dummycon_register_output_notifier() call directly after the "conswitchp !=
&dummy_con" comparison making it clear why that check is there.
Note the arch setup code will set conswitchp to either dummy_con or
vga_con, in the cases where it gets set to vga_con even though their is
no vga_con present we rely on vga_con_startup() to set conswitchp to
dummy_con. vga_con_startup() is guaranteed to happen before
fb_console_init() as it gets called as a console_initcall where as
fb_console_init() gets called as a subsys_initcall.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Having FRAMEBUFFER_CONSOLE_DEFERRED_TAKEOVER with fbdev+fbcon being build
as a module does not make much sense.
Having FRAMEBUFFER_CONSOLE_DEFERRED_TAKEOVER only when fbdev+fbcon are
builtin was always the intention, hence the =y checks but they were
checking the wrong option, fbcon is build as part of fb.ko, so we must
check for FB=y.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
drivers/video/fbdev/omap2/omapfb/dss/dss_features.c:895:2-5: WARNING: Use BUG_ON instead of if condition followed by BUG.
Please make sure the condition has no side effects (see conditional BUG_ON definition in include/asm-generic/bug.h)
Use BUG_ON instead of a if condition followed by BUG.
Semantic patch information:
This makes an effort to find cases where BUG() follows an if
condition on an expression and replaces the if condition and BUG()
with a BUG_ON having the conditional expression of the if statement
as argument.
Generated by: scripts/coccinelle/misc/bugon.cocci
Signed-off-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
drivers/video/fbdev/omap2/omapfb/omapfb-main.c:290:9-10: WARNING: return of 0/1 in function 'cmp_var_to_colormode' with return type bool
Return statements in functions returning bool should use
true/false instead of 1/0.
Generated by: scripts/coccinelle/misc/boolreturn.cocci
Signed-off-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
drivers/video/fbdev/omap2/omapfb/dss/core.c:141:2-26: WARNING: NULL check before some freeing functions is not needed.
NULL check before some freeing functions is not needed.
Based on checkpatch warning
"kfree(NULL) is safe this check is probably not required"
and kfreeaddr.cocci by Julia Lawall.
Generated by: scripts/coccinelle/free/ifnullfree.cocci
Signed-off-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
drivers/video/fbdev/omap2/omapfb/dss/core.c:141:2-26: WARNING: NULL check before some freeing functions is not needed.
NULL check before some freeing functions is not needed.
Based on checkpatch warning
"kfree(NULL) is safe this check is probably not required"
and kfreeaddr.cocci by Julia Lawall.
Generated by: scripts/coccinelle/free/ifnullfree.cocci
Fixes: 7378f11498 ("media: omap2: omapfb: allow building it with COMPILE_TEST")
Signed-off-by: kbuild test robot <fengguang.wu@intel.com>
Cc: Mauro Carvalho Chehab <m.chehab@samsung.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
drivers/video/fbdev/omap2/omapfb/dss/dss_features.c:895:2-5: WARNING: Use BUG_ON instead of if condition followed by BUG.
Please make sure the condition has no side effects (see conditional BUG_ON definition in include/asm-generic/bug.h)
Use BUG_ON instead of a if condition followed by BUG.
Semantic patch information:
This makes an effort to find cases where BUG() follows an if
condition on an expression and replaces the if condition and BUG()
with a BUG_ON having the conditional expression of the if statement
as argument.
Generated by: scripts/coccinelle/misc/bugon.cocci
Fixes: 7378f11498 ("media: omap2: omapfb: allow building it with COMPILE_TEST")
Signed-off-by: kbuild test robot <fengguang.wu@intel.com>
Cc: Mauro Carvalho Chehab <m.chehab@samsung.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
drivers/video/fbdev/omap2/omapfb/omapfb-main.c:290:9-10: WARNING: return of 0/1 in function 'cmp_var_to_colormode' with return type bool
Return statements in functions returning bool should use
true/false instead of 1/0.
Generated by: scripts/coccinelle/misc/boolreturn.cocci
Fixes: 7378f11498 ("media: omap2: omapfb: allow building it with COMPILE_TEST")
Signed-off-by: kbuild test robot <fengguang.wu@intel.com>
Cc: Mauro Carvalho Chehab <m.chehab@samsung.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Fix build warning when built as a loadable module.
amifb_setup() and amifb_setup_mcap() are only needed when the driver
is builtin.
This matches how the functions are called (using #ifndef MODULE).
../drivers/video/fbdev/amifb.c:2344:19: warning: 'amifb_setup' defined but not used [-Wunused-function]
static int __init amifb_setup(char *options)
../drivers/video/fbdev/amifb.c:2307:20: warning: 'amifb_setup_mcap' defined but not used [-Wunused-function]
static void __init amifb_setup_mcap(char *spec)
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
If the console is unlocked during registration, the console subsystem
generates significant amounts of warnings, which obfuscate actual
debugging messages. Setting ignore_console_lock_warning while debugging
console registration avoid the noise.
v3:
- manipulate ignore_console_lock_warning with atomic_{inc,dec}
v2:
- restore ignore_console_lock_warning if lock_fb_info() fails
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Reviewed-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Steven Rostedt (VMware) <rostedt@goodmis.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
spin_lock_irqsave and spin_unlock_irqrestore is inteded to be called from
a context where it is unknown if interrupts are enabled or disabled (such
as interrupt handlers). From a process context, we should call
spin_lock_irq and spin_unlock_irq, that avoids the costly pushf and popf
instructions.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Modern processors can detect linear memory accesses and prefetch data
automatically, so there's no need to use prefetch.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Currently, the udlfb driver only tests for identical bytes at the
beginning or at the end of a page and renders anything between the first
and last mismatching pixel. But pages are not the same as lines, so this
is quite suboptimal - if there is something modified at the beginning of a
page and at the end of a page, the whole page is rendered, even if most of
the page is not modified.
This patch makes it test for identical pixels at the beginning and end of
each rendering command. This patch improves identical byte detection by
41% when playing video in a window.
This patch also fixes a possible screen corruption if the user is writing
to the framebuffer while dlfb_render_hline is in progress - the pixel data
that is copied to the backbuffer with memcpy may be different from the
pixel data that is actually rendered to the hardware (because the content
of the framebuffer may change between memcpy and the rendering command).
We must make sure that we copy exactly the same pixel as the pixel that is
being rendered.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
[b.zolnierkie: fix code indent]
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
This patch changes udlfb so that it may reallocate the framebuffer when
setting higher-resolution mode. If we boot the system without monitor
attached, udlfb creates a framebuffer with the size 800x600. This patch
makes it possible to select higher videomode with the fbset command when
a monitor is attached.
Note that there is no reliable way to prevent the system from touching the
old framebuffer, so we must not free it. We add it to the list
dlfb->deferred_free and free it when the driver is unloaded.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
[b.zolnierkie: sparse fixes]
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Set the variable "line_length" in the function dlfb_ops_set_par. Without
this, we get garbage if we select different videomode with fbset.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Allocations larger than PAGE_ALLOC_COSTLY_ORDER are unreliable and they
may fail anytime. This patch fixes the udlfb driver so that when a large
alloactions fails, it tries to do multiple smaller allocations.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
The defio subsystem overwrites the method fb_osp->mmap. That method is
stored in module's static data - and that means that if we have multiple
diplaylink adapters, they will over write each other's method.
In order to avoid interference between multiple adapters, we copy the
fb_ops structure to a device-local memory.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
The udlfb driver reprograms the hardware everytime the user switches the
console, that makes quite unusable when working on the console.
This patch makes the driver remember the videomode we are in and avoid
reprogramming the hardware if we switch to the same videomode.
We mask the "activate" field and the "FB_VMODE_SMOOTH_XPAN" flag when
comparing the videomode, because they cause spurious switches when
switching to and from the Xserver.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
The displaylink hardware has such a peculiarity that it doesn't render a
command until next command is received. This produces occasional
corruption, such as when setting 22x11 font on the console, only the first
line of the cursor will be blinking if the cursor is located at some
specific columns.
When we end up with a repeating pixel, the driver has a bug that it leaves
one uninitialized byte after the command (and this byte is enough to flush
the command and render it - thus it fixes the screen corruption), however
whe we end up with a non-repeating pixel, there is no byte appended and
this results in temporary screen corruption.
This patch fixes the screen corruption by always appending a byte 0xAF at
the end of URB. It also removes the uninitialized byte.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
I observed that the performance of the udl fb driver degrades over time.
On a freshly booted machine, it takes 6 seconds to do "ls -la /usr/bin";
after some time of use, the same operation takes 14 seconds.
The reason is that the value of "limit_sem" decays over time.
The udl driver uses a semaphore "limit_set" to specify how many free urbs
are there on dlfb->urbs.list. If the count is zero, the "down" operation
will sleep until some urbs are added to the freelist.
In order to avoid some hypothetical deadlock, the driver will not call
"up" immediately, but it will offload it to a workqueue. The problem is
that if we call "schedule_delayed_work" on the same work item multiple
times, the work item may only be executed once.
This is happening:
* some urb completes
* dlfb_urb_completion adds it to the free list
* dlfb_urb_completion calls schedule_delayed_work to schedule the function
dlfb_release_urb_work to increase the semaphore count
* as the urb is on the free list, some other task grabs it and submits it
* the submitted urb completes, dlfb_urb_completion is called again
* dlfb_urb_completion calls schedule_delayed_work, but the work is already
scheduled, so it does nothing
* finally, dlfb_release_urb_work is called, it increases the semaphore
count by 1, although it should increase it by 2
So, the semaphore count is decreasing over time, and this causes gradual
performance degradation.
Note that in the current kernel, the "up" function may be called from
interrupt and it may race with the "down" function called by another
thread, so we don't have to offload the call of "up" to a workqueue at
all. This patch removes the workqueue code. The patch also changes
"down_interruptible" to "down" in dlfb_free_urb_list, so that we will
clean up the driver properly even if a signal arrives.
With this patch, the performance of udlfb no longer degrades.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
[b.zolnierkie: fix immediatelly -> immediately typo]
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
I have a USB display adapter using the udlfb driver and I use it on an ARM
board that doesn't have any graphics card. When I plug the adapter in, the
console is properly displayed, however when I unplug and re-plug the
adapter, the console is not displayed and I can't access it until I reboot
the board.
The reason is this:
When the adapter is unplugged, dlfb_usb_disconnect calls
unlink_framebuffer, then it waits until the reference count drops to zero
and then it deallocates the framebuffer. However, the console that is
attached to the framebuffer device keeps the reference count non-zero, so
the framebuffer device is never destroyed. When the USB adapter is plugged
again, it creates a new device /dev/fb1 and the console is not attached to
it.
This patch fixes the bug by unbinding the console from unlink_framebuffer.
The code to unbind the console is moved from do_unregister_framebuffer to
a function unbind_console. When the console is unbound, the reference
count drops to zero and the udlfb driver frees the framebuffer. When the
adapter is plugged back, a new framebuffer is created and the console is
attached to it.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Bernie Thompson <bernie@plugable.com>
Cc: Ladislav Michl <ladis@linux-mips.org>
Cc: stable@vger.kernel.org
[b.zolnierkie: preserve old behavior for do_unregister_framebuffer()]
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Currently, if the DT does not define num-interpolated-steps then
num_steps is undefined and the interpolation code will deploy randomly.
Fix with a simple initialize to zero.
Fixes: 573fe6d1c2 ("backlight: pwm_bl: Linear interpolation between brightness-levels")
Reported-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
On x86 some firmwares use a low non native resolution for the display when
they have shown some text messages. While keeping the bgrt filled with info
for the native resolution. If the bgrt image intended for the native
resolution still fits, it will be displayed very close to the right edge of
the display looking quite bad.
This commits adds a (heuristics based) checks for this and makes efifb
not show the boot graphics when this is the case.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Fix indentation warning (from gcc 8.1.0) in omap2/omapfb:
../drivers/video/fbdev/omap2/omapfb/dss/dispc.c: In function 'pixinc':
../drivers/video/fbdev/omap2/omapfb/dss/dispc.c:1859:2: warning: this 'else' clause does not guard... [-Wmisleading-indentation]
else
^~~~
../drivers/video/fbdev/omap2/omapfb/dss/dispc.c:1861:3: note: ...this statement, but the latter is misleadingly indented as if it were guarded by the 'else'
return 0;
^~~~~~
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Pointer 'in' is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
warning: variable 'in' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
The value of tmp being used in the switch statement has the range of
just 0..3 hence the case 4 statement can never be reached and is
deadcode and can be removed.
Detected by CoverityScan, CID#744384 ("Logically dead code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
The omapfb_register_client[] array has OMAPFB_PLANE_NUM elements so the
> should be >= or we are one element beyond the end of the array.
Fixes: 8b08cf2b64 ("OMAP: add TI OMAP framebuffer driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Imre Deak <imre.deak@solidboot.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Fix a build warning in viafbdev.c when CONFIG_PROC_FS is not enabled
by marking the unused function as __maybe_unused.
../drivers/video/fbdev/via/viafbdev.c:1471:12: warning: 'viafb_sup_odev_proc_show' defined but not used [-Wunused-function]
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
In a kernel configuration with both CONFIG_FB_OMAP=m and CONFIG_FB_OMAP2=m,
Kbuild fails to point out that we have two modules with the same name (omapfb.ko),
but instead fails with a cryptic error message like:
ERROR: "omapfb_register_panel" [drivers/video/fbdev/omap/lcd_osk.ko] undefined!
This can now happen when building a randconfig kernel with CONFIG_ARCH_OMAP1,
as the omap1 fbdev driver depends on that, whiel the omap2 fbdev driver can
now be built anywhere with CONFIG_COMPILE_TEST.
The solution is to rename one of the two modules, so for consistency with
the directory naming I decided to rename the omap2 version to omap2fb.ko.
Fixes: 7378f11498 ("media: omap2: omapfb: allow building it with COMPILE_TEST")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Tony Lindgren <tony@atomide.com>
Cc: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
goldfish_fb_probe() allocates memory for fb, but goldfish_fb_remove() does
not have deallocation of fb, which leads to memory leak on probe/remove.
The patch adds deallocation into goldfish_fb_remove().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Anton Vasilyev <vasilyev@ispras.ru>
Cc: Aleksandar Markovic <aleksandar.markovic@mips.com>
Cc: Miodrag Dinic <miodrag.dinic@mips.com>
Cc: Goran Ferenc <goran.ferenc@mips.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Fix up the indenting that confused sphinx. To make sure we
don't have to make the examples unreadable with escaping just
put them in as block quotes, that seems the simplest solution.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[b.zolnierkie: ported over fbdev changes]
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
The "mem" buffer has "size" bytes. The ">" should be ">=" to prevent
reading one character beyond the end of the array.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
It's been a pretty good while since kernel modesetting was introduced.
It has almost entirely replaced previous solutions which required
userspace modesetting, and I can't even recall any drivers off the top
of my head for modern day hardware that don't only support one or the
other. Even nvidia's ugly blob does not require the use of nomodeset,
and only requires that nouveau be blacklisted.
Effectively, the only thing nomodeset does in the year 2018 is disable
your graphics drivers. Since VESA is a thing, this will give many users
the false impression that they've actually fixed an issue they were
having with their machine simply because the laptop will boot up to a
degraded GUI. This of course, is never actually the case.
Things get even worse when you consider that there's still an enormous
amount of tutorials users find on the internet that still suggest adding
nomodeset, along with various users who have been around long enough to
still suggest it.
There really isn't any legitimate reason I can see for this to be an
option that's used by anyone else other then developers, or properly
informed users. So, let's end the confusion and start printing warnings
whenever it's enabled.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: "Jan H. Schönherr" <jschoenh@amazon.de>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Following pattern is often used:
for (i = 0; i < FB_MAX; i++) {
if (registered_fb[i]) {
...
}
}
Therefore, as Andy's suggestion, for_each_registered_fb() helper can
be introduced to make the code easier to read and write by reducing
indentation level. It also saves few lines of code in each occurrence.
This patch convert all part here at the same time.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Yisheng Xie <ysxie@foxmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: David Lechner <david@lechnology.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
In the quest to remove all stack VLA usage from the kernel[1], this moves
the buffer off the stack (since it could be as much as 1024 bytes), and
uses a new area in the cursor data structure. Additionally adds missed
documentation and removes redundant assignments.
[1] https://lkml.kernel.org/r/CA+55aFzCG-zNmZwX4A2FQpadafLfEzK6CC=qPXydAacU1RqZWA@mail.gmail.com
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
