Some SBE operations have extremely large responses and can require
several minutes to process the response. During this time, the device
lock must be held. If another process attempts an operation, it will
wait for the mutex for longer than the kernel hung task watchdog
allows. Therefore, use the interruptible function to lock the mutex.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20210803213016.44739-1-eajames@linux.ibm.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
The SBEFIFO timeout error requires special handling in userspace
to do recovery operations. Add a sysfs file to indicate a timeout
error, and notify pollers when a timeout occurs.
This will be used by the openpower-occ-control application.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20211019211749.38059-3-eajames@linux.ibm.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
If the SBEFIFO response indicates an error, store the response in the
user buffer and return an error. Previously, the user had no way of
obtaining the SBEFIFO FFDC.
The user's buffer now contains data in the event of a failure. No change
in the event of a successful transfer.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/20211019205307.36946-3-eajames@linux.ibm.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Allocate a large buffer for each OCC to handle response data. This
removes memory allocation during an operation, and also allows for
the maximum amount of SBE FFDC.
Previously for the putsram and attn commands, only 32 words would have
been available, and for getsram, only up to the size of the transfer.
SBE FFDC might be up to 8Kb.
The SBE interface expects data to be specified in units of words (4
bytes), defined as OCC_MAX_RESP_WORDS.
This change allows the full FFDC capture to be implemented, where before
it was not available.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/20211019205307.36946-2-eajames@linux.ibm.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Set and increment the sequence number during the submit operation.
This prevents sequence number conflicts between different users of
the interface. A sequence number conflict may result in a user
getting an OCC response meant for a different command. Since the
sequence number is now modified, the checksum must be calculated and
set before submitting the command.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20210721190231.117185-2-eajames@linux.ibm.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
On BMCs with lower timer resolution than 1ms, msleep(1) will take
way longer than 1ms, so looping 10k times won't wait for 10s but
significantly longer.
Fix this by using jiffies like the rest of the code.
Fixes: 9f4a8a2d7f ("fsi/sbefifo: Add driver for the SBE FIFO")
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Link: https://lore.kernel.org/r/20200724071518.430515-3-joel@jms.id.au
Signed-off-by: Joel Stanley <joel@jms.id.au>
When the SBE requests a reset via the down FIFO, that is also the
FIFO we should go and reset ;)
Fixes: 9f4a8a2d7f ("fsi/sbefifo: Add driver for the SBE FIFO")
Signed-off-by: Joachim Fenkes <FENKES@de.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20200724071518.430515-2-joel@jms.id.au
Signed-off-by: Joel Stanley <joel@jms.id.au>
When devm_ioremap_resource() fails, a clear enough error message will be
printed by its subfunction __devm_ioremap_resource(). The error
information contains the device name, failure cause, and possibly resource
information.
Therefore, remove the error printing here to simplify code and reduce the
binary size.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Link: https://patchwork.ozlabs.org/project/linux-fsi/patch/20210511085745.4340-1-thunder.leizhen@huawei.com/
Signed-off-by: Joel Stanley <joel@jms.id.au>
The lengthy timeout previously used sometimes resulted in
scheduling problems, detailed below. Therefore reduce the timeout
to 500us. This timeout selection is supported by the benchmarks
collected below with various clock dividers. This is purely the time
spent polling (reported by ktime_get()).
div 1: max:150us avg: 2us
div 2: max:155us avg: 3us
div 4: max:149us avg: 7us
div 8: max:153us avg: 13us
div 16: max:197us avg: 21us
div 32: max:181us avg: 50us
div 64: max:262us avg:100us
Jan 22 01:27:21 rain27bmc kernel: rcu: INFO: rcu_sched self-detected stall on CPU
Jan 22 01:27:21 rain27bmc kernel: rcu: 0-....: (2099 ticks this GP) idle=0ca/1/0x40000002 softirq=349573/349573 fqs=1048
Jan 22 01:27:21 rain27bmc kernel: (t=2100 jiffies g=841149 q=7163)
Jan 22 01:27:21 rain27bmc kernel: NMI backtrace for cpu 0
Jan 22 01:27:21 rain27bmc kernel: CPU: 0 PID: 5959 Comm: ibm-read-vpd Not tainted 5.8.17-a9b4ea8 #1
Jan 22 01:27:21 rain27bmc kernel: Hardware name: Generic DT based system
Jan 22 01:27:21 rain27bmc kernel: Backtrace:
Jan 22 01:27:25 rain27bmc kernel: [<8010d92c>] (dump_backtrace) from [<8010db80>] (show_stack+0x20/0x24)
...
Jan 22 01:27:25 rain27bmc kernel: [<8010130c>] (gic_handle_irq) from [<80100b0c>] (__irq_svc+0x6c/0x90)
Jan 22 01:27:25 rain27bmc kernel: Exception stack(0xb79159b0 to 0xb79159f8)
Jan 22 01:27:25 rain27bmc kernel: 59a0: 9e88e5d5 00000559 00000559 00000018
Jan 22 01:27:25 rain27bmc kernel: 59c0: 00000000 9f217c55 00000003 00000559 a0201c00 bfa4d048 bfa4d000 b7915a44
Jan 22 01:27:25 rain27bmc kernel: 59e0: 40e88f8a b7915a00 3254e553 80734924 80030113 ffffffff
Jan 22 01:27:25 rain27bmc kernel: r9:b7914000 r8:a0201c00 r7:b79159e4 r6:ffffffff r5:80030113 r4:80734924
Jan 22 01:27:25 rain27bmc kernel: [<807348b4>] (__opb_read) from [<80734d98>] (aspeed_master_read+0xbc/0xcc)
Jan 22 01:27:25 rain27bmc kernel: r10:00000004 r9:00000002 r8:80734cdc r7:bd33fa40 r6:00000004 r5:bd33f840
Jan 22 01:27:25 rain27bmc kernel: r4:00201c00
Jan 22 01:27:25 rain27bmc kernel: [<80734cdc>] (aspeed_master_read) from [<807320f0>] (fsi_master_read+0x6c/0x1bc)
...
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/20210211194846.35475-1-eajames@linux.ibm.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Log an error if the response checksum doesn't match the
calculated checksum.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20210209171235.20624-3-eajames@linux.ibm.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
If the OCC is not initialized and responds as such, the driver
should continue waiting for a valid response until the timeout
expires.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Fixes: 7ed98dddb7 ("fsi: Add On-Chip Controller (OCC) driver")
Link: https://lore.kernel.org/r/20210209171235.20624-2-eajames@linux.ibm.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
On a functioning FSI link there is not need to retry a write when doing
a scom in the driver.
Allow the higher layers (eg. userspace) to attempt a retry if they want,
or to accept that the address they are talking to is not accessible.
By removing the retries we can separate the error handling from retry
logic. In particular -EBUSY was used to force the get/put scom logic to
retry.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20210527070109.225198-1-joel@jms.id.au
Signed-off-by: Joel Stanley <joel@jms.id.au>
The error bits in the FSI2PIB status are only cleared by a reset. So
the driver needs to perform a reset after seeing any of the FSI2PIB
errors, otherwise subsequent operations will also look like failures.
Fixes: 6b293258cd ("fsi: scom: Major overhaul")
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20210329151344.14246-1-eajames@linux.ibm.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Currently the cfam_read and cfam_write functions return the provided
number of bytes given in the count parameter and not the error return
code in variable rc, hence all failures of read/writes are being
silently ignored. Fix this by returning the error code in rc.
Addresses-Coverity: ("Unused value")
Fixes: d1dcd67825 ("fsi: Add cfam char devices")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Jeremy Kerr <jk@ozlabs.org>
Link: https://lore.kernel.org/r/20210603122812.83587-1-colin.king@canonical.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this driver when it is built
as an external module.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Link: https://lore.kernel.org/r/1620896249-52769-1-git-send-email-zou_wei@huawei.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
- Driver for SB-TSI sensors
- Add support for P10 to fsi/occ
- Driver for LTC2992
- Driver for Delta power supplies Q54SJ108A2
- Support for NCT6687D added to nct6883 driver
- Support for Intel-based Xserves added to applesmc driver
- Driver for Maxim MAX127
- Support for AMD family 19h model 01h added to amd_energy driver
- Driver to support Corsair PSU
- Driver for STMicroelectronics PM6764 Voltage Regulator
- Various minor bug fixes and improvements
-----BEGIN PGP SIGNATURE-----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=YomY
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-v5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
"New drivers:
- SB-TSI sensors
- Lineat Technology LTC2992
- Delta power supplies Q54SJ108A2
- Maxim MAX127
- Corsair PSU
- STMicroelectronics PM6764 Voltage Regulator
New chip support:
- P10 added to fsi/occ driver
- NCT6687D added to nct6883 driver
- Intel-based Xserves added to applesmc driver
- AMD family 19h model 01h added to amd_energy driver
And various minor bug fixes and improvements"
* tag 'hwmon-for-v5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (41 commits)
dt-bindings: (hwmon/sbtsi_temp) Add SB-TSI hwmon driver bindings
hwmon: (sbtsi) Add documentation
hwmon: (sbtsi) Add basic support for SB-TSI sensors
hwmon: (iio_hwmon) Drop bogus __refdata annotation
hwmon: (xgene) Drop bogus __refdata annotation
dt-bindings: hwmon: convert AD ADM1275 bindings to dt-schema
hwmon: (occ) Add new temperature sensor type
fsi: occ: Add support for P10
dt-bindings: fsi: Add P10 OCC device documentation
dt-bindings: hwmon: convert TI ADS7828 bindings to dt-schema
dt-bindings: hwmon: convert AD AD741x bindings to dt-schema
dt-bindings: hwmon: convert TI INA2xx bindings to dt-schema
hwmon: (ltc2992) Fix less than zero comparisons with an unsigned integer
hwmon: (pmbus/q54sj108a2) Correct title underline length
dt-bindings: hwmon: Add documentation for ltc2992
hwmon: (ltc2992) Add support for GPIOs.
hwmon: (ltc2992) Add support
hwmon: (pmbus) Driver for Delta power supplies Q54SJ108A2
hwmon: Add driver for STMicroelectronics PM6764 Voltage Regulator
hwmon: (nct6683) Support NCT6687D.
...
The P10 OCC has a different SRAM address for the command and response
buffers. In addition, the SBE commands to access the SRAM have changed
format. Add versioning to the driver to handle these differences.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20201120010315.190737-3-joel@jms.id.au
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
There is nothing to prevent multiple commands being executed
simultaneously. Add a mutex to prevent this.
Fixes: 606397d67f ("fsi: Add ast2600 master driver")
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Milton Miller <miltonm@us.ibm.com>
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20201120004929.185239-1-joel@jms.id.au
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Systems have a line for restting the remote CFAM. This is not part of
the FSI master, but is associated with it, so it makes sense to include
it in the master driver.
This exposes a sysfs interface to reset the cfam, abstracting away the
direction and polarity of the GPIO, as well as the timing of the reset
pulse. Userspace will be blocked until the reset pulse is finished.
The reset is hard coded to be in the range of (900, 1000) us. It was
observed with a scope to regularly be just over 1ms.
If the device tree property is not preset the driver will silently
continue.
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20200728025527.174503-6-joel@jms.id.au
Signed-off-by: Joel Stanley <joel@jms.id.au>
For testing and hardware debugging a user may wish to override the
divisor at runtime. By setting fsi_master_aspeed.bus_div=N, the divisor
will be set to N, if 0 < N <= 0x3ff.
This is a module parameter and not a device tree option as it will only
need to be set when testing or debugging.
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/20200728025527.174503-5-joel@jms.id.au
Signed-off-by: Joel Stanley <joel@jms.id.au>
Testing of Tacoma has shown that the ASPEED master can be run at maximum
speed.
The exception is when wired externally with a cable, in which case we
use a divisor of two to ensure reliable operation.
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/20200728025527.174503-4-joel@jms.id.au
Signed-off-by: Joel Stanley <joel@jms.id.au>
Some FSI capable systems have internal FSI signals, and some have
external cabled FSI. Software can detect which machine this is by
reading a jumper GPIO, and also control which pins the signals are
routed to through a mux GPIO.
This attempts to find the GPIOs at probe time. If they are not present
in the device tree the driver will not error and continue as before.
The mux GPIO is owned by the FSI driver to ensure it is not modified at
runtime. The routing jumper obtained as non-exclusive to allow other
software to inspect it's state.
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20200728025527.174503-3-joel@jms.id.au
Signed-off-by: Joel Stanley <joel@jms.id.au>
The only usage of scom_ids is to assign its address to the id_table
field in the fsi_driver struct, which is a const pointer, so make it
const to allow the compiler to put it in read-only memory
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
The only usage of sbefifo_ids is to assign its address to the id_table
field in the fsi_driver struct, which is a const pointer, so make it
const to allow the compiler to put it in read-only memory
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
The only usage of hub_master_ids is to assign its address to the
id_table field in the fsi_driver struct, which is a const pointer, so
make it const to allow the compiler to put it in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Both the Aspeed and hub masters read back the link enable register
after enabling the link, but this is unnecessary, so remove it.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
The driver ought to claim local bus ownership of the slave it's
communicating with.
This is for multi-master setups. The slave (in theory) will deny access
to masters who try to access the CFAM address space but who don't "own"
the bus.
As driver doesn't seem to perform any other teardown there is no need to
"un-claim" ownership at teardown. Also I'm not aware of any multi-master
setup using this driver so it shouldn't actually matter. Also, the
hardware doesn't seem to enforce this despite being required in the
specification...
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
In the case that links don't have slaves or fail to be accessed, the
master should disable the link during the scan since it won't be using
the slave.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Add the ability to disable a link with a boolean parameter to the
link_enable function. This is necessary so that the master can disable
links that it isn't using; for example, links to slaves that fail
initialization.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
In case of error, the function platform_device_register_full()
returns ERR_PTR() and never returns NULL. The NULL test in the
return value check should be replaced with IS_ERR().
Signed-off-by: Xu Wang <vulab@iscas.ac.cn>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Joel Stanley <joel@jms.id.au>
In order to access more than the second hub link, 23-bit addressing is
required. The core provides the highest two bits of address as the slave
ID to the master.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Acked-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
There is a spelling mistake in a dev_err error message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Since commit 84af7a6194 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.
This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.
There are a variety of indentation styles found.
a) 4 spaces + '---help---'
b) 7 spaces + '---help---'
c) 8 spaces + '---help---'
d) 1 space + 1 tab + '---help---'
e) 1 tab + '---help---' (correct indentation)
f) 1 tab + 1 space + '---help---'
g) 1 tab + 2 spaces + '---help---'
In order to convert all of them to 1 tab + 'help', I ran the
following commend:
$ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Currently CONFIG_FSI_MASTER_ASPEED=y implicitly depends on
CONFIG_HAS_IOMEM=y; consequently, on architectures without IOMEM we get
the following build error:
ld: drivers/fsi/fsi-master-aspeed.o: in function `fsi_master_aspeed_probe':
drivers/fsi/fsi-master-aspeed.c:436: undefined reference to `devm_ioremap_resource'
Fix the build error by adding the unspecified dependency.
Fixes: 606397d67f ("fsi: Add ast2600 master driver")
Cc: stable@vger.kernel.org
Reported-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Brendan Higgins <brendanhiggins@google.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20200131034832.294268-1-joel@jms.id.au
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The data byte order selection registers in the APB2OPB primarily expose some
internal plumbing necessary to get correct write accesses onto the OPB.
OPB write cycles require "data mirroring" across the 32-bit data bus to
support variable data width slaves that don't implement "byte enables".
For slaves that do implement byte enables the master can signal which
bytes on the data bus the slave should consider valid.
The data mirroring behaviour is specified by the following table:
+-----------------+----------+-----------------------------------+
| | | 32-bit Data Bus |
+---------+-------+----------+---------+---------+-------+-------+
| | | | | | | |
| ABus | Mn_BE | Request | Dbus | Dbus | Dbus | Dbus |
| (30:31) | (0:3) | Transfer | 0:7 | 8:15 | 16:23 | 24:31 |
| | | Size | byte0 | byte1 | byte2 | byte3 |
+---------+-------+----------+---------+---------+-------+-------+
| 00 | 1111 | fullword | byte0 | byte1 | byte2 | byte3 |
+---------+-------+----------+---------+---------+-------+-------+
| 00 | 1110 | halfword | byte0 | byte1 | byte2 | |
+---------+-------+----------+---------+---------+-------+-------+
| 01 | 0111 | byte | _byte1_ | byte1 | byte2 | byte3 |
+---------+-------+----------+---------+---------+-------+-------+
| 00 | 1100 | halfword | byte0 | byte1 | | |
+---------+-------+----------+---------+---------+-------+-------+
| 01 | 0110 | byte | _byte1_ | byte1 | byte2 | |
+---------+-------+----------+---------+---------+-------+-------+
| 10 | 0011 | halfword | _byte2_ | _byte3_ | byte2 | byte3 |
+---------+-------+----------+---------+---------+-------+-------+
| 00 | 1000 | byte | byte0 | | | |
+---------+-------+----------+---------+---------+-------+-------+
| 01 | 0100 | byte | _byte1_ | byte1 | | |
+---------+-------+----------+---------+---------+-------+-------+
| 10 | 0010 | byte | _byte2_ | | byte2 | |
+---------+-------+----------+---------+---------+-------+-------+
| 11 | 0001 | byte | _byte3_ | _byte3_ | | byte3 |
+---------+-------+----------+---------+---------+-------+-------+
Mirrored data values are highlighted by underscores in the Dbus columns.
The values in the ABus and Request Transfer Size columns correspond to
values in the field names listed in the write data order select register
descriptions.
Similar configuration registers are exposed for reads which enables the
secondary purpose of configuring hardware endian conversions. It appears the
data bus byte order is switched around in hardware so set the registers such
that we can access the correct values for all widths. The values were
determined by experimentation on hardware against fixed CFAM register
values to configure the read data order, then in combination with the
table above and the register layout documentation in the AST2600
datasheet performing write/read cycles to configure the write data order
registers.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Acked-by: Alistair Popple <alistair@popple.id.au>
Link: https://lore.kernel.org/r/20191108051945.7109-12-joel@jms.id.au
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These trace points help with debugging the FSI master. They show the low
level reads, writes and error states of the master.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20191108051945.7109-11-joel@jms.id.au
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ast2600 BMC has a pair of FSI masters in it, behind an AHB to OPB
bridge.
The master driver supports reads and writes of full words, half word and
byte accesses to remote CFAMs. It can perform very basic error recovery
through resetting of the FSI port when an error is detected, and the
issuing of breaks and terms.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Acked-by: Alistair Popple <alistair@popple.id.au>
--
v2:
- remove debugging
- squash in fixes
Link: https://lore.kernel.org/r/20191108051945.7109-10-joel@jms.id.au
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The FSI master registers are common to the hub and AST2600 master (and
the FSP2, if someone was to upstream a driver for that).
Add defines to the fsi-master.h header, and introduce headings to
delineate the existing low level details.
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20191108051945.7109-8-joel@jms.id.au
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are no users outside of this file.
Fixes: 0604d53d4da8 ("fsi: Add fsi-master class")
Signed-off-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20191108051945.7109-7-joel@jms.id.au
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Subtracting the offset delta from four-byte alignment lead to wrapping
of the requested length where `count` is less than `off`. Generalise the
length handling to enable and optimise aligned access sizes for all
offset and size combinations. The new formula produces the following
results for given offset and count values:
offset count | length
--------------+-------
0 1 | 1
0 2 | 2
0 3 | 2
0 4 | 4
0 5 | 4
1 1 | 1
1 2 | 1
1 3 | 1
1 4 | 1
1 5 | 1
2 1 | 1
2 2 | 2
2 3 | 2
2 4 | 2
2 5 | 2
3 1 | 1
3 2 | 1
3 3 | 1
3 4 | 1
3 5 | 1
We might need something like this for the cfam chardevs as well, for
example we don't currently implement any alignment restrictions /
handling in the hardware master driver.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20191108051945.7109-6-joel@jms.id.au
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Populate fsi_master_class->dev_attrs with the existing attribute
definitions, so we don't need to explicitly register.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Acked-by: Alistair Popple <alistair@popple.id.au>
Link: https://lore.kernel.org/r/20191108051945.7109-3-joel@jms.id.au
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This change adds a device class for FSI masters, allowing access under
/sys/class/fsi-master/, and easier udev rules.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Acked-by: Alistair Popple <alistair@popple.id.au>
Link: https://lore.kernel.org/r/20191108051945.7109-2-joel@jms.id.au
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The scom driver currently fails out of operations if certain system
errors are flagged in the status register; system checkstop, special
attention, or recoverable error. These errors won't impact the ability
of the scom engine to perform operations, so the driver should continue
under these conditions.
Also, don't do a PIB reset for these conditions, since it won't help.
Fixes: 6b293258cd ("fsi: scom: Major overhaul")
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Jeremy Kerr <jk@ozlabs.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20190827041249.13381-1-jk@ozlabs.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SBE fifo operations should be allowed while the SBE is in any of the
"IPL" states. Operations should succeed in this state.
Fixes: 9f4a8a2d7f fsi/sbefifo: Add driver for the SBE FIFO
Reviewed-by: Joel Stanley <joel@jms.id.au>
Tested-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/1561575415-3282-1-git-send-email-eajames@linux.ibm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Add MAINTAINERS entry. There is now a git tree and a mailing
list/patchwork for collecting FSI patches
- Bug fix for error driver registration error paths
- Correction for the OCC hwmon driver to meet the spec
-----BEGIN PGP SIGNATURE-----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=3yOz
-----END PGP SIGNATURE-----
Merge tag 'fsi-for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/fsi into char-misc-next
Joel writes:
FSI changes for 5.3
- Add MAINTAINERS entry. There is now a git tree and a mailing
list/patchwork for collecting FSI patches
- Bug fix for error driver registration error paths
- Correction for the OCC hwmon driver to meet the spec
* tag 'fsi-for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/fsi:
fsi/core: Fix error paths on CFAM init
OCC: FSI and hwmon: Add sequence numbering
MAINTAINERS: Add FSI subsystem
Change d1dcd67825 re-worked the struct fsi_slave initialisation in
fsi_slave_init, but introduced a few inconsitencies: the slave->dev is
now registered through cdev_device_add, but we may kfree() the device
out from underneath the cdev registration. We may also leave an IDA
allocated.
This change fixes the error paths, so that we kfree() only before the
device is registered with the core code. We also move the smode write to
before we start creating proper devices, as it's the most likely to
fail. We also remove the IDA-allocated minor on error, and properly
clean up the of_node.
Fixes: d1dcd67825 ("fsi: Add cfam char devices")
Reported-by: Lei YU <mine260309@gmail.com>
Tested-by: John Wang <wangzqbj@inspur.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Sequence numbering of the commands submitted to the OCC is required by
the OCC interface specification. Add sequence numbering and check for
the correct sequence number on the response.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Lei YU <mine260309@gmail.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
