- Set up mvebu BAR 0 so MSI works even if bootloader doesn't do this
(Shmuel Hazan)
* remotes/lorenzo/pci/mvebu:
PCI: mvebu: Setup BAR0 in order to fix MSI
- Fix loongson class code quirk so it happens early enough (Tiezhu Yang)
* remotes/lorenzo/pci/loongson:
PCI: loongson: Use DECLARE_PCI_FIXUP_EARLY for bridge_class_quirk()
- Fix hv timing issue that causes kdump failures (Wei Hu)
- Make some hv functions static (Wei Yongjun)
* remotes/lorenzo/pci/hv:
PCI: hv: Make some functions static
PCI: hv: Fix a timing issue which causes kdump to fail occasionally
- Convert cadence to use standard "dma-ranges" DT property instead of its
own "cdns,no-bar-match-nbits" (Kishon Vijay Abraham I)
- Fix pm_runtime_put_sync() issues in cadence error paths (Kishon Vijay
Abraham I)
- Add PTR_ALIGN_DOWN macro (Kishon Vijay Abraham I)
- Convert cadence r/w accessors to only 32-bit accesses (Kishon Vijay
Abraham I)
- Add cadence support to start Link and check Link status (Kishon Vijay
Abraham I)
- Allow custom PCI ops for cadence-based drivers (Kishon Vijay Abraham I)
- Remove "mem" from cadence reg binding since it's not memory and it
overlaps the PCIe config and memory region (Kishon Vijay Abraham I)
- Add cadence ->cpu_addr_fixup() for platforms that require absolute
addresses in the ATU, not just offsets (Kishon Vijay Abraham I)
- Update cadence Vendor IDs using local management registers, not
architected config space (Kishon Vijay Abraham I)
- Add cadence endpoint driver MSI-X support (Kishon Vijay Abraham I)
- Add bindings and driver for TI J721E SoC, supporting both host and
endpoint mode (Kishon Vijay Abraham I)
* remotes/lorenzo/pci/cadence:
MAINTAINERS: Add Kishon Vijay Abraham I for TI J721E SoC PCIe
misc: pci_endpoint_test: Add J721E in pci_device_id table
PCI: j721e: Add TI J721E PCIe driver
dt-bindings: PCI: Add EP mode dt-bindings for TI's J721E SoC
dt-bindings: PCI: Add host mode dt-bindings for TI's J721E SoC
PCI: cadence: Add MSI-X support to Endpoint driver
PCI: cadence: Fix updating Vendor ID and Subsystem Vendor ID register
PCI: cadence: Add new *ops* for CPU addr fixup
dt-bindings: PCI: cadence: Remove "mem" from reg binding
PCI: cadence: Allow pci_host_bridge to have custom pci_ops
PCI: cadence: Add support to start link and verify link status
PCI: cadence: Convert all r/w accessors to perform only 32-bit accesses
linux/kernel.h: Add PTR_ALIGN_DOWN macro
PCI: cadence: Fix cdns_pcie_{host|ep}_setup() error path
PCI: cadence: Use "dma-ranges" instead of "cdns,no-bar-match-nbits" property
- Use pci_channel_state_t instead of enum pci_channel_state (Luc Van
Oostenryck)
- Simplify __aer_print_error() (Bjorn Helgaas)
- Log AER correctable errors as warning, not error (Matt Jolly)
- Rename pci_aer_clear_device_status() to pcie_clear_device_status() (Bjorn
Helgaas)
- Clear PCIe Device Status errors only if OS owns AER (Jonathan Cameron)
* pci/error:
PCI/ERR: Clear PCIe Device Status errors only if OS owns AER
PCI/ERR: Rename pci_aer_clear_device_status() to pcie_clear_device_status()
PCI/AER: Log correctable errors as warning, not error
PCI/AER: Simplify __aer_print_error()
PCI: Use 'pci_channel_state_t' instead of 'enum pci_channel_state'
Add support for PCIe controller in J721E SoC. The controller uses the
Cadence PCIe core programmed by pcie-cadence*.c. The PCIe controller
will work in both host mode and device mode.
Some of the features of the controller are:
*) Supports both RC mode and EP mode
*) Supports MSI and MSI-X support
*) Supports upto GEN3 speed mode
*) Supports SR-IOV capability
*) Ability to route all transactions via SMMU (support will be added
in a later patch).
Link: https://lore.kernel.org/r/20200722110317.4744-14-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Fix a missing __iomem tag in the init_pfn() function. This fixes a sparse
warning of the form:
$ make C=2 drivers/pci/switch/
drivers/pci/switch/switchtec.c:... incorrect type assignment(different address spaces)
Fixes: 080b47def5 ("MicroSemi Switchtec management interface driver")
Link: https://lore.kernel.org/r/20200728192434.18993-2-logang@deltatee.com
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Fix a number of missing __iomem and __user tags in the ioctl functions of
the switchtec driver. This fixes a number of sparse warnings of the form:
$ make C=2 drivers/pci/switch/
drivers/pci/switch/switchtec.c:... incorrect type in ... (different address spaces)
Fixes: 52eabba5bc ("switchtec: Add IOCTLs to the Switchtec driver")
Link: https://lore.kernel.org/r/20200728192434.18993-1-logang@deltatee.com
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The sparse tool report build warnings as follows:
drivers/pci/hotplug/rpadlpar_core.c:355:5: warning: symbol 'dlpar_remove_pci_slot' was not declared. Should it be static?
drivers/pci/hotplug/rpadlpar_core.c:461:12: warning: symbol 'rpadlpar_io_init' was not declared. Should it be static?
drivers/pci/hotplug/rpadlpar_core.c:473:6: warning: symbol 'rpadlpar_io_exit' was not declared. Should it be static?
Those functions are not used outside of this file, so mark them static.
Also mark rpadlpar_io_exit() as __exit.
Link: https://lore.kernel.org/r/20200721151735.41181-1-weiyongjun1@huawei.com
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Allow P2PDMA if the CPU vendor is AMD and family is 0x17 (Zen) or greater.
[bhelgaas: commit log, simplify #if/#else/#endif]
Link: https://lore.kernel.org/r/20200729231844.4653-1-logang@deltatee.com
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: Huang Rui <ray.huang@amd.com>
The acpi_get_table() should be coupled with acpi_put_table() if the mapped
table is not used at runtime to release the table mapping.
In pci_quirk_amd_sb_acs(), IVRS table is just used for checking AMD IOMMU
is supported, not used at runtime, so put the table after using it.
Fixes: 15b100dfd1 ("PCI: Claim ACS support for AMD southbridge devices")
Link: https://lore.kernel.org/r/1595411068-15440-1-git-send-email-guohanjun@huawei.com
Signed-off-by: Hanjun Guo <guohanjun@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Announce the device, e.g.,
pci 0000:00:00.0: [8086:5910] type 00 class 0x060000
after running early fixups, so the log message reflects any device type or
class code fixups.
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/1595833615-8049-1-git-send-email-yangtiezhu@loongson.cn
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
We are seeing AMD Radeon Pro W5700 doesn't work when IOMMU is enabled:
iommu ivhd0: AMD-Vi: Event logged [IOTLB_INV_TIMEOUT device=63:00.0 address=0x42b5b01a0]
iommu ivhd0: AMD-Vi: Event logged [IOTLB_INV_TIMEOUT device=63:00.0 address=0x42b5b01c0]
The error also makes graphics driver fail to probe the device.
It appears to be the same issue as commit 5e89cd303e ("PCI: Mark AMD
Navi14 GPU rev 0xc5 ATS as broken") addresses, and indeed the same ATS
quirk can workaround the issue.
See-also: 5e89cd303e ("PCI: Mark AMD Navi14 GPU rev 0xc5 ATS as broken")
See-also: d28ca864c4 ("PCI: Mark AMD Stoney Radeon R7 GPU ATS as broken")
See-also: 9b44b0b09d ("PCI: Mark AMD Stoney GPU ATS as broken")
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=208725
Link: https://lore.kernel.org/r/20200728104554.28927-1-kai.heng.feng@canonical.com
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
388c8c16ab ("PCI: add routines for debugging and handling lost
interrupts") added pci_lost_interrupt() that apparently never has had a
single user. Remove it.
Link: https://lore.kernel.org/r/e328d059-3068-6a40-28df-f81f616d15a0@gmail.com
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Implement ->set_msix() and ->get_msix() callback functions in order
to configure MSIX capability in the PCIe endpoint controller.
Add cdns_pcie_ep_send_msix_irq() to send MSIX interrupts to Host.
cdns_pcie_ep_send_msix_irq() gets the MSIX table address (virtual
address) from "struct cdns_pcie_epf" that gets initialized in
->set_bar() call back function.
[kishon@ti.com: Re-implement MSIX support in accordance with the
re-designed core MSI-X interfaces]
Link: https://lore.kernel.org/r/20200722110317.4744-11-kishon@ti.com
Signed-off-by: Alan Douglas <adouglas@cadence.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
sparse report build warning as follows:
drivers/pci/controller/pci-hyperv.c:941:5: warning:
symbol 'hv_read_config_block' was not declared. Should it be static?
drivers/pci/controller/pci-hyperv.c:1021:5: warning:
symbol 'hv_write_config_block' was not declared. Should it be static?
drivers/pci/controller/pci-hyperv.c:1090:5: warning:
symbol 'hv_register_block_invalidate' was not declared. Should it be static?
Those functions are not used outside of this file, so mark them static.
Link: https://lore.kernel.org/r/20200706135234.80758-1-weiyongjun1@huawei.com
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
The HiSilicon non-ECAM PCIe has been broken since March 2016 commit
7e57fd1444 ("PCI: designware: Move Root Complex setup code to
dw_pcie_setup_rc()"). The reason is this commit moved the iATU setup code
from dw_pcie_host_init() to dw_pcie_setup_rc(), but the hisi driver never
calls dw_pcie_setup_rc(). The result is the PCI memory space is never
configured and the driver can't work. It's also clear it has an iATU as
the config space accesses use it.
There's also no dts file using either "hisilicon,hip05-pcie" or
"hisilicon,hip06-pcie".
Link: https://lore.kernel.org/r/20200724224204.3249055-1-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Zhou Wang <wangzhou1@hisilicon.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Commit 1b79c52844 ("PCI: cadence: Add host driver for Cadence PCIe
controller") in order to update Vendor ID, directly wrote to
PCI_VENDOR_ID register. However PCI_VENDOR_ID in root port configuration
space is read-only register and writing to it will have no effect.
Use local management register to configure Vendor ID and Subsystem Vendor
ID.
Link: https://lore.kernel.org/r/20200722110317.4744-10-kishon@ti.com
Fixes: 1b79c52844 ("PCI: cadence: Add host driver for Cadence PCIe controller")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Cadence driver uses "mem" memory resource to obtain the offset of
configuration space address region, memory space address region and
message space address region. The obtained offset is used to program
the Address Translation Unit (ATU). However certain platforms like TI's
J721E SoC require the absolute address to be programmed in the ATU and
not just the offset. Add new *ops* for CPU addr fixup for the platform
drivers to provide the correct address to be programmed in the ATU.
Link: https://lore.kernel.org/r/20200722110317.4744-9-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Certain platforms like TI's J721E allows only 32-bit configuration
space access. In such cases pci_generic_config_read and
pci_generic_config_write cannot be used. Add support in Cadence core
to let pci_host_bridge have custom pci_ops.
Link: https://lore.kernel.org/r/20200722110317.4744-7-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Add cdns_pcie_ops to start link and verify link status. The registers
to start link and to check link status is in Platform specific PCIe
wrapper. Add support for platform specific drivers to add callback
functions for the PCIe Cadence core to start link and verify link status.
Link: https://lore.kernel.org/r/20200722110317.4744-6-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Certain platforms like TI's J721E using Cadence PCIe IP can perform only
32-bit accesses for reading or writing to Cadence registers. Convert all
read and write accesses to 32-bit in Cadence PCIe driver in preparation
for adding PCIe support in TI's J721E SoC.
Also add spin lock to disable interrupts while modifying PCI_STATUS
register while raising legacy interrupt since PCI_STATUS is accessible
by both remote RC and EP and time between read and write should be
minimized.
Link: https://lore.kernel.org/r/20200722110317.4744-5-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
commit bd22885aa1 ("PCI: cadence: Refactor driver to use as a core
library") while refactoring the Cadence PCIe driver to be used as
library, removed pm_runtime_get_sync() from cdns_pcie_ep_setup()
and cdns_pcie_host_setup() but missed to remove the corresponding
pm_runtime_put_sync() in the error path. Fix it here.
Link: https://lore.kernel.org/r/20200722110317.4744-3-kishon@ti.com
Fixes: bd22885aa1 ("PCI: cadence: Refactor driver to use as a core library")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Cadence PCIe core driver (host mode) uses "cdns,no-bar-match-nbits"
property to configure the number of bits passed through from PCIe
address to internal address in Inbound Address Translation register.
This only used the NO MATCH BAR.
However standard PCI dt-binding already defines "dma-ranges" to
describe the address ranges accessible by PCIe controller. Add support
in Cadence PCIe host driver to parse dma-ranges and configure the
inbound regions for BAR0, BAR1 and NO MATCH BAR. Cadence IP specifies
maximum size for BAR0 as 256GB, maximum size for BAR1 as 2 GB.
This adds support to take the next biggest region in "dma-ranges" and
find the smallest BAR that each of the regions fit in and if there is
no BAR big enough to hold the region, split the region to see if it can
be fitted using multiple BARs.
"dma-ranges" of J721E will be
dma-ranges = <0x02000000 0x0 0x0 0x0 0x0 0x10000 0x0>;
Since there is no BAR which can hold 2^48 size, NO_MATCH_BAR will be
used here.
Legacy device tree binding compatibility is maintained by retaining
support for "cdns,no-bar-match-nbits".
Link: https://lore.kernel.org/r/20200722110317.4744-2-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Kdump could fail sometime on Hyper-V guest because the retry in
hv_pci_enter_d0() releases child device structures in hv_pci_bus_exit().
Although there is a second asynchronous device relations message sending
from the host, if this message arrives to the guest after
hv_send_resource_allocated() is called, the retry would fail.
Fix the problem by moving retry to hv_pci_probe() and start the retry
from hv_pci_query_relations() call. This will cause a device relations
message to arrive to the guest synchronously; the guest would then be
able to rebuild the child device structures before calling
hv_send_resource_allocated().
Link: https://lore.kernel.org/r/20200727071731.18516-1-weh@microsoft.com
Fixes: c81992e7f4 ("PCI: hv: Retry PCI bus D0 entry on invalid device state")
Signed-off-by: Wei Hu <weh@microsoft.com>
[lorenzo.pieralisi@arm.com: fixed a comment and commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
For SR-IOV, the PF PRI is shared between the PF and any associated VFs, and
the PRI Capability is allowed for PFs but not for VFs. Searching for the
PRI Capability on a VF always fails, even if its associated PF supports
PRI.
Add pci_pri_supported() to check whether device or its associated PF
supports PRI.
[bhelgaas: commit log, avoid "!!"]
Fixes: b16d0cb9e2 ("iommu/vt-d: Always enable PASID/PRI PCI capabilities before ATS")
Link: https://lore.kernel.org/r/1595543849-19692-1-git-send-email-ashok.raj@intel.com
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lu Baolu <baolu.lu@linux.intel.com>
Acked-by: Joerg Roedel <jroedel@suse.de>
Cc: stable@vger.kernel.org # v4.4+
pcie_clear_device_status() resets the error bits in the PCIe Device Status
Register (PCI_EXP_DEVSTA).
Previously we did this unconditionally, but on ACPI systems, the _OSC AER
bit negotiates control of the AER capability. Per sec 4.5.1 of the System
Firmware Intermediary _OSC and DPC Updates ECN [1], this bit also covers
other error enable/status bits including the following:
Correctable Error Reporting Enable
Non-Fatal Error Reporting Enable
Fatal Error Reporting Enable
Unsupported Request Reporting Enable
These bits are all in the PCIe Device Control register (the ECN omitted
"Reporting", but I think that's a typo), so by implication the _OSC AER bit
also applies to the error status bits in the PCIe Device Status register:
Correctable Error Detected
Non-Fatal Error Detected
Fatal Error Detected
Unsupported Request Detected
Clear the PCIe Device Status error bits only when the OS controls the AER
capability and related error enable/status bits. If platform firmware
controls the AER capability, firmware is responsible for clearing these
bits.
One call path leading here is:
ghes_do_proc
ghes_handle_aer
aer_recover_queue
schedule_work(&aer_recover_work)
...
aer_recover_work_func
pcie_do_recovery
pcie_clear_device_status
[1] System Firmware Intermediary (SFI) _OSC and DPC Updates ECN, Feb 24,
2020, affecting PCI Firmware Specification, Rev. 3.2
https://members.pcisig.com/wg/PCI-SIG/document/14076
[bhelgaas: commit log, move test from pcie_clear_device_status() to callers]
Link: https://lore.kernel.org/r/20200622113523.891666-1-Jonathan.Cameron@huawei.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
pci_aer_clear_device_status() clears the error bits in the PCIe Device
Status Register (PCI_EXP_DEVSTA). Every PCIe device has this register,
regardless of whether it supports AER.
Rename pci_aer_clear_device_status() to pcie_clear_device_status() to make
clear that it is PCIe-specific but not AER-specific. Move it to
drivers/pci/pci.c, again since it's not AER-specific. No functional change
intended.
Link: https://lore.kernel.org/r/20200717195619.766662-1-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
When there is no PCIe card connected and advk_pcie_rd_conf() or
advk_pcie_wr_conf() is called for PCI bus which doesn't belong to emulated
root bridge, the aardvark driver throws the following error message:
advk-pcie d0070000.pcie: config read/write timed out
Obviously accessing PCIe registers of disconnected card is not possible.
Extend check in advk_pcie_valid_device() function for validating
availability of PCIe bus. If PCIe link is down, then the device is marked
as Not Found and the driver does not try to access these registers.
This is just an optimization to prevent accessing PCIe registers when card
is disconnected. Trying to access PCIe registers of disconnected card does
not cause any crash, kernel just needs to wait for a timeout. So if card
disappear immediately after checking for PCIe link (before accessing PCIe
registers), it does not cause any problems.
Link: https://lore.kernel.org/r/20200702083036.12230-1-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
According to the datasheet of Loongson LS7A bridge chip, the old version
of Loongson LS7A PCIE port has a wrong value about PCI class which is
0x060000, the correct value should be 0x060400, this bug can be fixed by
"dev->class = PCI_CLASS_BRIDGE_PCI << 8;" at the software level and it
was fixed in hardware in the latest LS7A versions.
In order to maintain downward compatibility, use DECLARE_PCI_FIXUP_EARLY
instead of DECLARE_PCI_FIXUP_HEADER for bridge_class_quirk() to fix it as
early as possible.
Otherwise, in the function pci_setup_device(), the related code about
"dev->class" such as "class = dev->class >> 8;" and "dev->transparent
= ((dev->class & 0xff) == 1);" maybe get wrong value without EARLY fixup.
Link: https://lore.kernel.org/r/1595065176-460-1-git-send-email-yangtiezhu@loongson.cn
Fixes: 1f58cca5cf ("PCI: Add Loongson PCI Controller support")
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
When I cat ASPM parameter 'policy' by sysfs, it displays as follows. Add a
newline for easy reading. Other sysfs attributes already include a
newline.
[root@localhost ~]# cat /sys/module/pcie_aspm/parameters/policy
[default] performance powersave powersupersave [root@localhost ~]#
Fixes: 7d715a6c1a ("PCI: add PCI Express ASPM support")
Link: https://lore.kernel.org/r/1594972765-10404-1-git-send-email-wangxiongfeng2@huawei.com
Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Use devm_platform_ioremap_resource_byname() to simplify the code
since it contains platform_get_resource_byname() and
devm_ioremap_resource() respectively.
Link: https://lore.kernel.org/r/20200708164013.5076-1-zhengdejin5@gmail.com
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Reviewed-by: Rob Herring <robh@kernel.org>
According to the Armada XP datasheet, section 10.2.6: "in order for
the device to do a write to the MSI doorbell address, it needs to write
to a register in the internal registers space".
As a result of the requirement above, without this patch, MSI won't
function and therefore some devices won't operate properly without
pci=nomsi.
This requirement was not present at the time of writing this driver
since the vendor u-boot always initializes all PCIe controllers
(incl. BAR0 initialization) and for some time, the vendor u-boot was
the only available bootloader for this driver's SoCs (e.g. A38x,A37x,
etc).
Tested on an Armada 385 board on mainline u-boot (2020.4), without
u-boot PCI initialization and the following PCIe devices:
- Wilocity Wil6200 rev 2 (wil6210)
- Qualcomm Atheros QCA6174 (ath10k_pci)
Both failed to get a response from the device after loading the
firmware and seem to operate properly with this patch.
Link: https://lore.kernel.org/r/20200623060334.108444-1-sh@tkos.co.il
Signed-off-by: Shmuel Hazan <sh@tkos.co.il>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
kobject_init_and_add() takes a reference even when it fails. If it returns
an error, kobject_put() must be called to clean up the memory associated
with the object.
When kobject_init_and_add() fails, call kobject_put() instead of kfree().
b8eb718348 ("net-sysfs: Fix reference count leak in
rx|netdev_queue_add_kobject") fixed a similar problem.
Link: https://lore.kernel.org/r/20200528021322.1984-1-wu000273@umn.edu
Signed-off-by: Qiushi Wu <wu000273@umn.edu>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Currently the ACS capability is being looked up at a number of places. Read
and store it once at enumeration so that it can be used by all later. No
functional change intended.
Link: https://lore.kernel.org/r/20200707224604.3737893-2-rajatja@google.com
Signed-off-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Move pci_enable_acs() and dependencies further up in the source code to
avoid having to forward declare it when we make it static in near future.
No functional changes intended.
Link: https://lore.kernel.org/r/20200707224604.3737893-1-rajatja@google.com
Signed-off-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Use kzalloc() instead of kmalloc() in the panic message.
[bhelgaas: drop similar ibmphp_pci.c change since it's not obviously
correct]
Link: https://lore.kernel.org/r/1594279708-34369-1-git-send-email-wang.yi59@zte.com.cn
Signed-off-by: Liao Pingfang <liao.pingfang@zte.com.cn>
Signed-off-by: Yi Wang <wang.yi59@zte.com.cn>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
PCIe correctable errors are recovered by hardware with no need for software
intervention (PCIe r5.0, sec 6.2.2.1).
Reduce the log level of correctable errors from KERN_ERR to KERN_WARNING.
The bug reports below are for correctable error logging. This doesn't fix
the cause of those reports, but it may make the messages less alarming.
[bhelgaas: commit log, use pci_printk() to avoid code duplication]
Link: https://bugzilla.kernel.org/show_bug.cgi?id=201517
Link: https://bugzilla.kernel.org/show_bug.cgi?id=196183
Link: https://lore.kernel.org/r/20200618155511.16009-1-Kangie@footclan.ninja
Signed-off-by: Matt Jolly <Kangie@footclan.ninja>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
aer_correctable_error_string[] and aer_uncorrectable_error_string[] have
descriptions of AER error status bits. Add NULL entries to these tables so
all entries for bits 0-31 are defined. Then we don't have to check for
ARRAY_SIZE() when decoding a status word, which simplifies
__aer_print_error().
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
device_attach() returning failure indicates a driver error while trying to
probe the device. In such a scenario, the PCI device should still be added
in the system and be visible to the user.
When device_attach() fails, merely warn about it and keep the PCI device in
the system.
This partially reverts ab1a187bba ("PCI: Check device_attach() return
value always").
Link: https://lore.kernel.org/r/20200706233240.3245512-1-rajatja@google.com
Signed-off-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: stable@vger.kernel.org # v4.6+
