The syzkaller USB fuzzer found a general-protection-fault bug in the
yurex driver. The fault occurs when a device has been unplugged; the
driver's interrupt-URB handler logs an error message referring to the
device by name, after the device has been unregistered and its name
deallocated.
This problem is caused by the fact that the interrupt URB isn't
cancelled until the driver's private data structure is released, which
can happen long after the device is gone. The cure is to make sure
that the interrupt URB is killed before yurex_disconnect() returns;
this is exactly the sort of thing that usb_poison_urb() was meant for.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: syzbot+2eb9121678bdb36e6d57@syzkaller.appspotmail.com
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Change the validation of number_of_packets in get_pipe to compare the
number of packets to a fixed maximum number of packets allowed, set to
be 1024. This number was chosen due to it being used by other drivers as
well, for example drivers/usb/host/uhci-q.c
Background/reason:
The get_pipe function in stub_rx.c validates the number of packets in
isochronous mode and aborts with an error if that number is too large,
in order to prevent malicious input from possibly triggering large
memory allocations. This was previously done by checking whether
pdu->u.cmd_submit.number_of_packets is bigger than the number of packets
that would be needed for pdu->u.cmd_submit.transfer_buffer_length bytes
if all except possibly the last packet had maximum length, given by
usb_endpoint_maxp(epd) * usb_endpoint_maxp_mult(epd). This leads to an
error if URBs with packets shorter than the maximum possible length are
submitted, which is allowed according to
Documentation/driver-api/usb/URB.rst and occurs for example with the
snd-usb-audio driver.
Fixes: c6688ef9f2 ("usbip: fix stub_rx: harden CMD_SUBMIT path to handle malicious input")
Signed-off-by: Malte Leip <malte@leip.net>
Cc: stable <stable@vger.kernel.org>
Acked-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The syzkaller fuzzer reported a bug in the USB hub driver which turned
out to be caused by a negative runtime-PM usage counter. This allowed
a hub to be runtime suspended at a time when the driver did not expect
it. The symptom is a WARNING issued because the hub's status URB is
submitted while it is already active:
URB 0000000031fb463e submitted while active
WARNING: CPU: 0 PID: 2917 at drivers/usb/core/urb.c:363
The negative runtime-PM usage count was caused by an unfortunate
design decision made when runtime PM was first implemented for USB.
At that time, USB class drivers were allowed to unbind from their
interfaces without balancing the usage counter (i.e., leaving it with
a positive count). The core code would take care of setting the
counter back to 0 before allowing another driver to bind to the
interface.
Later on when runtime PM was implemented for the entire kernel, the
opposite decision was made: Drivers were required to balance their
runtime-PM get and put calls. In order to maintain backward
compatibility, however, the USB subsystem adapted to the new
implementation by keeping an independent usage counter for each
interface and using it to automatically adjust the normal usage
counter back to 0 whenever a driver was unbound.
This approach involves duplicating information, but what is worse, it
doesn't work properly in cases where a USB class driver delays
decrementing the usage counter until after the driver's disconnect()
routine has returned and the counter has been adjusted back to 0.
Doing so would cause the usage counter to become negative. There's
even a warning about this in the USB power management documentation!
As it happens, this is exactly what the hub driver does. The
kick_hub_wq() routine increments the runtime-PM usage counter, and the
corresponding decrement is carried out by hub_event() in the context
of the hub_wq work-queue thread. This work routine may sometimes run
after the driver has been unbound from its interface, and when it does
it causes the usage counter to go negative.
It is not possible for hub_disconnect() to wait for a pending
hub_event() call to finish, because hub_disconnect() is called with
the device lock held and hub_event() acquires that lock. The only
feasible fix is to reverse the original design decision: remove the
duplicate interface-specific usage counter and require USB drivers to
balance their runtime PM gets and puts. As far as I know, all
existing drivers currently do this.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: syzbot+7634edaea4d0b341c625@syzkaller.appspotmail.com
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The syzkaller USB fuzzer identified a failure mode in which dummy-hcd
would never give back an unlinked URB. This causes usb_kill_urb() to
hang, leading to WARNINGs and unkillable threads.
In dummy-hcd, all URBs are given back by the dummy_timer() routine as
it scans through the list of pending URBS. Failure to give back URBs
can be caused by failure to start or early exit from the scanning
loop. The code currently has two such pathways: One is triggered when
an unsupported bus transfer speed is encountered, and the other by
exhausting the simulated bandwidth for USB transfers during a frame.
This patch removes those two paths, thereby allowing all unlinked URBs
to be given back in a timely manner. It adds a check for the bus
speed when the gadget first starts running, so that dummy_timer() will
never thereafter encounter an unsupported speed. And it prevents the
loop from exiting as soon as the total bandwidth has been used up (the
scanning loop continues, giving back unlinked URBs as they are found,
but not transferring any more data).
Thanks to Andrey Konovalov for manually running the syzkaller fuzzer
to help track down the source of the bug.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: syzbot+d919b0f29d7b5a4994b9@syzkaller.appspotmail.com
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some drivers (such as the vub300 MMC driver) expect usb_string() to
return a properly NUL-terminated string, even when an error occurs.
(In fact, vub300's probe routine doesn't bother to check the return
code from usb_string().) When the driver goes on to use an
unterminated string, it leads to kernel errors such as
stack-out-of-bounds, as found by the syzkaller USB fuzzer.
An out-of-range string index argument is not at all unlikely, given
that some devices don't provide string descriptors and therefore list
0 as the value for their string indexes. This patch makes
usb_string() return a properly terminated empty string along with the
-EINVAL error code when an out-of-range index is encountered.
And since a USB string index is a single-byte value, indexes >= 256
are just as invalid as values of 0 or below.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: syzbot+b75b85111c10b8d680f1@syzkaller.appspotmail.com
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's a fix for a long-standing refcount issue in the mos7720 parport
implementation, and a set of device id updates.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCXJ4o5gAKCRALxc3C7H1l
CAzlAPwLLrPEd6Tut9Tk+HACqgwGT3OlBedXQDxyN5o/UsMCHAEAtsX6LYpiVCFb
vZEk8NXH2adevF00n9ICccjc9un6iQg=
=kz2p
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-5.1-rc3' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for 5.1-rc3
Here's a fix for a long-standing refcount issue in the mos7720 parport
implementation, and a set of device id updates.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
* tag 'usb-serial-5.1-rc3' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: option: add Olicard 600
USB: serial: cp210x: add new device id
USB: serial: mos7720: fix mos_parport refcount imbalance on error path
USB: serial: option: set driver_info for SIM5218 and compatibles
USB: serial: ftdi_sio: add additional NovaTech products
USB: serial: option: add support for Quectel EM12
One deadlock fix on f_hid. NET2280 got a fix on its dequeue
implementation and a fix for overrun of OUT messages.
DWC3 learned about another Intel product: Comment Lake PCH.
NET2272 got a similar fix to NET2280 on its dequeue implementation.
-----BEGIN PGP SIGNATURE-----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=2R9U
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v5.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v5.1-rc2
One deadlock fix on f_hid. NET2280 got a fix on its dequeue
implementation and a fix for overrun of OUT messages.
DWC3 learned about another Intel product: Comment Lake PCH.
NET2272 got a similar fix to NET2280 on its dequeue implementation.
* tag 'fixes-for-v5.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb:
USB: gadget: f_hid: fix deadlock in f_hidg_write()
usb: gadget: net2272: Fix net2272_dequeue()
usb: gadget: net2280: Fix net2280_dequeue()
usb: gadget: net2280: Fix overrun of OUT messages
usb: dwc3: pci: add support for Comet Lake PCH ID
Lorenz Messtechnik has a device that is controlled by the cp210x driver,
so add the device id to the driver. The device id was provided by
Silicon-Labs for the devices from this vendor.
Reported-by: Uli <t9cpu@web.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
When the kernel is compiled with preemption enabled, the URB completion
handler can run in parallel with the work responsible for waking up the
tty layer. If the URB handler sets the EVENT_TTY_WAKEUP bit during the
call to tty_port_tty_wakeup() to signal that there is room for additional
input, it will be cleared at the end of this call. As a result, TX traffic
on the upper layer will be blocked.
This can be seen with a kernel configured with CONFIG_PREEMPT, and a fast
modem connected with PPP running over a USB CDC-ACM port.
Use test_and_clear_bit() instead, which ensures that each wakeup requested
by the URB completion code will trigger a call to tty_port_tty_wakeup().
Fixes: 1aba579f3c cdc-acm: handle read pipe errors
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When EXTCON is a loadable module, mtu3 fails to link as built-in:
drivers/usb/mtu3/mtu3_plat.o: In function `mtu3_probe':
mtu3_plat.c:(.text+0x690): undefined reference to `extcon_get_edev_by_phandle'
Add a Kconfig dependency to force mtu3 also to be a loadable module
if extconn is, but still allow it to be built without extcon.
Fixes: d0ed062a8b ("usb: mtu3: dual-role mode support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
of_match_device in usb251xb_probe can fail and returns a NULL pointer.
The patch avoids a potential NULL pointer dereference in this scenario.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Reviewed-by: Richard Leitner <richard.leitner@skidata.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some PHYs do not support PHY_MODE_USB_HOST_SS, i.e. USB 3.0 or higher.
Fall back and try the more generic PHY_MODE_USB_HOST if it fails.
Fixes: b97a313483 ("usb: core: comply to PHY framework")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 2f31a67f01 ("usb: xhci: Prevent bus suspend if a port connect
change or polling state is detected") was intended to prevent ports that
were still link training from being forced to U3 suspend state mid
enumeration.
This solved enumeration issues for devices with slow link training.
Turns out some devices are stuck in the link training/polling state,
and thus that patch will prevent suspend completely for these devices.
This is seen with USB3 card readers in some MacBooks.
Instead of preventing suspend, give some time to complete the link
training. On successful training the port will end up as connected
and enabled.
If port instead is stuck in link training the bus suspend will continue
suspending after 360ms (10 * 36ms) timeout (tPollingLFPSTimeout).
Original patch was sent to stable, this one should go there as well
Fixes: 2f31a67f01 ("usb: xhci: Prevent bus suspend if a port connect change or polling state is detected")
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The xhci debug capability (DbC) feature did its memory cleanup with
spinlock held. dma_free_coherent() warns if called with interrupts
disabled
move the memory cleanup outside the spinlock
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A suspended SS port in U3 link state will go to U0 when resumed, but
can almost immediately after that enter U1 or U2 link power save
states before host controller driver reads the port status.
Host controller driver only checks for U0 state, and might miss
the finished resume, leaving flags unclear and skip notifying usb
code of the wake.
Add U1 and U2 to the possible link states when checking for finished
port resume.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The write_parport_reg_nonblock() helper takes a reference to the struct
mos_parport, but failed to release it in a couple of error paths after
allocation failures, leading to a memory leak.
Johan said that move the kref_get() and mos_parport assignment to the
end of urbtrack initialisation is a better way, so move it. and
mos_parport do not used until urbtrack initialisation.
Signed-off-by: Lin Yi <teroincn@163.com>
Fixes: b69578df7e ("USB: usbserial: mos7720: add support for parallel port on moschip 7715")
Cc: stable <stable@vger.kernel.org> # 2.6.35
Signed-off-by: Johan Hovold <johan@kernel.org>
In f_hidg_write() the write_spinlock is acquired before calling
usb_ep_queue() which causes a deadlock when dummy_hcd is being used.
This is because dummy_queue() callbacks into f_hidg_req_complete() which
tries to acquire the same spinlock. This is (part of) the backtrace when
the deadlock occurs:
0xffffffffc06b1410 in f_hidg_req_complete
0xffffffffc06a590a in usb_gadget_giveback_request
0xffffffffc06cfff2 in dummy_queue
0xffffffffc06a4b96 in usb_ep_queue
0xffffffffc06b1eb6 in f_hidg_write
0xffffffff8127730b in __vfs_write
0xffffffff812774d1 in vfs_write
0xffffffff81277725 in SYSC_write
Fix this by releasing the write_spinlock before calling usb_ep_queue()
Reviewed-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Tested-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: stable@vger.kernel.org # 4.11+
Fixes: 749494b6bd ("usb: gadget: f_hid: fix: Move IN request allocation to set_alt()")
Signed-off-by: Radoslav Gerganov <rgerganov@vmware.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Restore the status of ep->stopped in function net2272_dequeue().
When the given request is not found in the endpoint queue
the function returns -EINVAL without restoring the state of
ep->stopped. Thus the endpoint keeps blocked and does not transfer
any data anymore.
This fix is only compile-tested, since we do not have a
corresponding hardware. An analogous fix was tested in the sibling
driver. See "usb: gadget: net2280: Fix net2280_dequeue()"
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When a request must be dequeued with net2280_dequeue() e.g. due
to a device clear action and the same request is finished by the
function scan_dma_completions() then the function net2280_dequeue()
does not find the request in the following search loop and
returns the error -EINVAL without restoring the status ep->stopped.
Thus the endpoint keeps blocked and does not receive any data
anymore.
This fix restores the status and does not issue an error message.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The OUT endpoint normally blocks (NAK) subsequent packets when a
short packet was received and returns an incomplete queue entry to
the gadget driver. Thereby the gadget driver can detect a short packet
when reading queue entries with a length that is not equal to a
multiple of packet size.
The start_queue() function enables receiving OUT packets regardless of
the content of the OUT FIFO. This results in a race: With the current
code, it's possible that the "!ep->is_in && (readl(&ep->regs->ep_stat)
& BIT(NAK_OUT_PACKETS))" test in start_dma() will fail, then a short
packet will be received, and then start_queue() will call
stop_out_naking(). That's what we don't want (OUT naking gets turned
off while there is data in the FIFO) because then the next driver
request might receive a mixture of old and new packets.
With the patch, this race can't occur because the FIFO's state is
tested after we know that OUT naking is already turned on, and OUT
naking is stopped only when both of the conditions are met. This
ensures that all received data is delivered to the gadget driver,
which can detect a short packet now before new packets are appended
to the last short packet.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
There is no need to compare *port* with >= 0 because such comparison
of an unsigned value is always true.
Fix this by removing such comparison.
Addresses-Coverity-ID: 1443949 ("Unsigned compared against 0")
Fixes: 02a50b8750 ("usb: usb251xb: add usb data lane port swap feature")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Richard Leitner <richard.leitner@skidata.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are cases where multiple device tree nodes point to the
same phy node by means of the "phys" property, but we should
only consider those nodes that are marked as available rather
than just any node.
Fixes: 98bfb39466 ("usb: of: add an api to get dr_mode by the phy node")
Cc: stable@vger.kernel.org # v4.4+
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PD 2.0 sinks are supposed to accept src-capabilities with a 3.0 header and
simply ignore any src PDOs which the sink does not understand such as PPS
but some 2.0 sinks instead ignore the entire PD_DATA_SOURCE_CAP message,
causing contract negotiation to fail.
This commit fixes such sinks not working by re-trying the contract
negotiation with PD-2.0 source-caps messages if we don't have a contract
after PD_N_HARD_RESET_COUNT hard-reset attempts.
The problem fixed by this commit was noticed with a Type-C to VGA dongle.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently there is no check on platform_get_irq() return value
in case it fails, hence never actually reporting any errors and
causing unexpected behavior when using such value as argument
for function regmap_irq_get_virq().
Fix this by adding a proper check, a message error and return
*irq* in case platform_get_irq() fails.
Addresses-Coverity-ID: 1443899 ("Improper use of negative value")
Fixes: d2061f9cc3 ("usb: typec: add driver for Intel Whiskey Cove PMIC USB Type-C PHY")
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SIMCom SIM5218 and compatible devices have 5 USB interfaces, only 4
of which are serial ports. The fifth is a network interface supported
by the qmi-wwan driver. Furthermore, the serial ports do not support
modem control signals. Add driver_info flags to reflect this.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Fixes: ec0cd94d88 ("usb: option: add SIMCom SIM5218")
Cc: stable <stable@vger.kernel.org> # 3.2
Signed-off-by: Johan Hovold <johan@kernel.org>
Add PIDs for the NovaTech OrionLX+ and Orion I/O so they can be
automatically detected.
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The Quectel EM12 is a Cat. 12 LTE modem. It behaves in the exactly the
same way as the EP06 (including the dynamic configuration behavior), so
the same checks on reserved interfaces, etc. are needed.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
As all the memblock allocation functions return NULL in case of error
rather than panic(), the duplicates with _nopanic suffix can be removed.
Link: http://lkml.kernel.org/r/1548057848-15136-22-git-send-email-rppt@linux.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Petr Mladek <pmladek@suse.com> [printk]
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Cc: Christoph Hellwig <hch@lst.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Dennis Zhou <dennis@kernel.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Guo Ren <guoren@kernel.org>
Cc: Guo Ren <ren_guo@c-sky.com> [c-sky]
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Juergen Gross <jgross@suse.com> [Xen]
Cc: Mark Salter <msalter@redhat.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Rob Herring <robh@kernel.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Stafford Horne <shorne@gmail.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- add debugfs support for dumping dma-debug information (Corentin Labbe)
- Kconfig cleanups (Andy Shevchenko and me)
- debugfs cleanups (Greg Kroah-Hartman)
- improve dma_map_resource and use it in the media code
- arch_setup_dma_ops / arch_teardown_dma_ops cleanups
- various small cleanups and improvements for the per-device coherent
allocator
- make the DMA mask an upper bound and don't fail "too large" dma mask
in the remaning two architectures - this will allow big driver
cleanups in the following merge windows
-----BEGIN PGP SIGNATURE-----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=nAMI
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-5.1' of git://git.infradead.org/users/hch/dma-mapping
Pull DMA mapping updates from Christoph Hellwig:
- add debugfs support for dumping dma-debug information (Corentin
Labbe)
- Kconfig cleanups (Andy Shevchenko and me)
- debugfs cleanups (Greg Kroah-Hartman)
- improve dma_map_resource and use it in the media code
- arch_setup_dma_ops / arch_teardown_dma_ops cleanups
- various small cleanups and improvements for the per-device coherent
allocator
- make the DMA mask an upper bound and don't fail "too large" dma mask
in the remaning two architectures - this will allow big driver
cleanups in the following merge windows
* tag 'dma-mapping-5.1' of git://git.infradead.org/users/hch/dma-mapping: (21 commits)
Documentation/DMA-API-HOWTO: update dma_mask sections
sparc64/pci_sun4v: allow large DMA masks
sparc64/iommu: allow large DMA masks
sparc64: refactor the ali DMA quirk
ccio: allow large DMA masks
dma-mapping: remove the DMA_MEMORY_EXCLUSIVE flag
dma-mapping: remove dma_mark_declared_memory_occupied
dma-mapping: move CONFIG_DMA_CMA to kernel/dma/Kconfig
dma-mapping: improve selection of dma_declare_coherent availability
dma-mapping: remove an incorrect __iommem annotation
of: select OF_RESERVED_MEM automatically
device.h: dma_mem is only needed for HAVE_GENERIC_DMA_COHERENT
mfd/sm501: depend on HAS_DMA
dma-mapping: add a kconfig symbol for arch_teardown_dma_ops availability
dma-mapping: add a kconfig symbol for arch_setup_dma_ops availability
dma-mapping: move debug configuration options to kernel/dma
dma-debug: add dumping facility via debugfs
dma: debug: no need to check return value of debugfs_create functions
videobuf2: replace a layering violation with dma_map_resource
dma-mapping: don't BUG when calling dma_map_resource on RAM
...
This is mostly update of the usual drivers: arcmsr, qla2xxx, lpfc,
hisi_sas, target/iscsi and target/core. Additionally Christoph
refactored gdth as part of the dma changes. The major mid-layer
change this time is the removal of bidi commands and with them the
whole of the osd/exofs driver and filesystem.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXIC54SYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishT1GAPwJEV23
ExPiPsnuVgKj49nLTagZ3rILRQcYNbL+MNYqxQEA0cT8FHzSDBfWY5OKPNE+RQ8z
f69LpXGmMpuagKGvvd4=
=Fhy1
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly update of the usual drivers: arcmsr, qla2xxx, lpfc,
hisi_sas, target/iscsi and target/core.
Additionally Christoph refactored gdth as part of the dma changes. The
major mid-layer change this time is the removal of bidi commands and
with them the whole of the osd/exofs driver and filesystem. This is a
major simplification for block and mq in particular"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (240 commits)
scsi: cxgb4i: validate tcp sequence number only if chip version <= T5
scsi: cxgb4i: get pf number from lldi->pf
scsi: core: replace GFP_ATOMIC with GFP_KERNEL in scsi_scan.c
scsi: mpt3sas: Add missing breaks in switch statements
scsi: aacraid: Fix missing break in switch statement
scsi: kill command serial number
scsi: csiostor: drop serial_number usage
scsi: mvumi: use request tag instead of serial_number
scsi: dpt_i2o: remove serial number usage
scsi: st: osst: Remove negative constant left-shifts
scsi: ufs-bsg: Allow reading descriptors
scsi: ufs: Allow reading descriptor via raw upiu
scsi: ufs-bsg: Change the calling convention for write descriptor
scsi: ufs: Remove unused device quirks
Revert "scsi: ufs: disable vccq if it's not needed by UFS device"
scsi: megaraid_sas: Remove a bunch of set but not used variables
scsi: clean obsolete return values of eh_timed_out
scsi: sd: Optimal I/O size should be a multiple of physical block size
scsi: MAINTAINERS: SCSI initiator and target tweaks
scsi: fcoe: make use of fip_mode enum complete
...
-----BEGIN PGP SIGNATURE-----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=vf9L
-----END PGP SIGNATURE-----
Merge tag 'pci-v5.1-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- Use match_string() instead of reimplementing it (Andy Shevchenko)
- Enable SERR# forwarding for all bridges (Bharat Kumar Gogada)
- Use Latency Tolerance Reporting if already enabled by platform (Bjorn
Helgaas)
- Save/restore LTR info for suspend/resume (Bjorn Helgaas)
- Fix DPC use of uninitialized data (Dongdong Liu)
- Probe bridge window attributes only once at enumeration-time to fix
device accesses during rescan (Bjorn Helgaas)
- Return BAR size (not "size -1 ") from pci_size() to simplify code (Du
Changbin)
- Use config header type (not class code) identify bridges more
reliably (Honghui Zhang)
- Work around Intel Denverton incorrect Trace Hub BAR size reporting
(Alexander Shishkin)
- Reorder pciehp cached state/hardware state updates to avoid missed
interrupts (Mika Westerberg)
- Turn ibmphp semaphores into completions or mutexes (Arnd Bergmann)
- Mark expected switch fall-through (Mathieu Malaterre)
- Use of_node_name_eq() for node name comparisons (Rob Herring)
- Add ACS and pciehp quirks for HXT SD4800 (Shunyong Yang)
- Consolidate Rohm Vendor ID definitions (Andy Shevchenko)
- Use u32 (not __u32) for things not exposed to userspace (Logan
Gunthorpe)
- Fix locking semantics of bus and slot reset interfaces (Alex
Williamson)
- Update PCIEPORTBUS Kconfig help text (Hou Zhiqiang)
- Allow portdrv to claim subtractive decode Ports so PCIe services will
work for them (Honghui Zhang)
- Report PCIe links that become degraded at run-time (Alexandru
Gagniuc)
- Blacklist Gigabyte X299 Root Port power management to fix Thunderbolt
hotplug (Mika Westerberg)
- Revert runtime PM suspend/resume callbacks that broke PME on network
cable plug (Mika Westerberg)
- Disable Data Link State Changed interrupts to prevent wakeup
immediately after suspend (Mika Westerberg)
- Extend altera to support Stratix 10 (Ley Foon Tan)
- Allow building altera driver on ARM64 (Ley Foon Tan)
- Replace Douglas with Tom Joseph as Cadence PCI host/endpoint
maintainer (Lorenzo Pieralisi)
- Add DT support for R-Car RZ/G2E (R8A774C0) (Fabrizio Castro)
- Add dra72x/dra74x/dra76x SoC compatible strings (Kishon Vijay Abraham I)
- Enable x2 mode support for dra72x/dra74x/dra76x SoC (Kishon Vijay
Abraham I)
- Configure dra7xx PHY to PCIe mode (Kishon Vijay Abraham I)
- Simplify dwc (remove unnecessary header includes, name variables
consistently, reduce inverted logic, etc) (Gustavo Pimentel)
- Add i.MX8MQ support (Andrey Smirnov)
- Add message to help debug dwc MSI-X mask bit errors (Gustavo
Pimentel)
- Work around imx7d PCIe PLL erratum (Trent Piepho)
- Don't assert qcom reset GPIO during probe (Bjorn Andersson)
- Skip dwc MSI init if MSIs have been disabled (Lucas Stach)
- Use memcpy_fromio()/memcpy_toio() instead of plain memcpy() in PCI
endpoint framework (Wen Yang)
- Add interface to discover supported endpoint features to replace a
bitfield that wasn't flexible enough (Kishon Vijay Abraham I)
- Implement the new supported-feature interface for designware-plat,
dra7xx, rockchip, cadence (Kishon Vijay Abraham I)
- Fix issues with 64-bit BAR in endpoints (Kishon Vijay Abraham I)
- Add layerscape endpoint mode support (Xiaowei Bao)
- Remove duplicate struct hv_vp_set in favor of struct hv_vpset (Maya
Nakamura)
- Rework hv_irq_unmask() to use cpumask_to_vpset() instead of
open-coded reimplementation (Maya Nakamura)
- Align Hyper-V struct retarget_msi_interrupt arguments (Maya Nakamura)
- Fix mediatek MMIO size computation to enable full size of available
MMIO space (Honghui Zhang)
- Fix mediatek DMA window size computation to allow endpoint DMA access
to full DRAM address range (Honghui Zhang)
- Fix mvebu prefetchable BAR regression caused by common bridge
emulation that assumed all bridges had prefetchable windows (Thomas
Petazzoni)
- Make advk_pci_bridge_emul_ops static (Wei Yongjun)
- Configure MPS settings for VMD root ports (Jon Derrick)
* tag 'pci-v5.1-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (92 commits)
PCI: Update PCIEPORTBUS Kconfig help text
PCI: Fix "try" semantics of bus and slot reset
PCI/LINK: Report degraded links via link bandwidth notification
dt-bindings: PCI: altera: Add altr,pcie-root-port-2.0
PCI: altera: Enable driver on ARM64
PCI: altera: Add Stratix 10 PCIe support
PCI/PME: Fix possible use-after-free on remove
PCI: aardvark: Make symbol 'advk_pci_bridge_emul_ops' static
PCI: dwc: skip MSI init if MSIs have been explicitly disabled
PCI: hv: Refactor hv_irq_unmask() to use cpumask_to_vpset()
PCI: hv: Replace hv_vp_set with hv_vpset
PCI: hv: Add __aligned(8) to struct retarget_msi_interrupt
PCI: mediatek: Enlarge PCIe2AHB window size to support 4GB DRAM
PCI: mediatek: Fix memory mapped IO range size computation
PCI: dwc: Remove superfluous shifting in definitions
PCI: dwc: Make use of GENMASK/FIELD_PREP
PCI: dwc: Make use of BIT() in constant definitions
PCI: dwc: Share code for dw_pcie_rd/wr_other_conf()
PCI: dwc: Make use of IS_ALIGNED()
PCI: imx6: Add code to request/control "pcie_aux" clock for i.MX8MQ
...
Here is the big USB/PHY driver pull request for 5.1-rc1.
The usual set of gadget driver updates, phy driver updates (you will
have a merge issue with Kconfig and Makefile), xhci updates, and typec
additions. Also included in here are a lot of small cleanups and fixes
and driver updates where needed.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXH+hsw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynfNwCgqKKg+MxJ9pFjrwfWYOrbk+BBe2UAn2Elp4ia
8FTdneQfN2J8Hhc6KGXE
=Kx9I
-----END PGP SIGNATURE-----
Merge tag 'usb-5.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY updates from Greg KH:
"Here is the big USB/PHY driver pull request for 5.1-rc1.
The usual set of gadget driver updates, phy driver updates, xhci
updates, and typec additions. Also included in here are a lot of small
cleanups and fixes and driver updates where needed.
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-5.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (167 commits)
wusb: Remove unnecessary static function ckhdid_printf
usb: core: make default autosuspend delay configurable
usb: core: Fix typo in description of "authorized_default"
usb: chipidea: Refactor USB PHY selection and keep a single PHY
usb: chipidea: Grab the (legacy) USB PHY by phandle first
usb: chipidea: imx: set power polarity
dt-bindings: usb: ci-hdrc-usb2: add property power-active-high
usb: chipidea: imx: remove unused header files
usb: chipidea: tegra: Fix missed ci_hdrc_remove_device()
usb: core: add option of only authorizing internal devices
usb: typec: tps6598x: handle block writes separately with plain-I2C adapters
usb: xhci: Fix for Enabling USB ROLE SWITCH QUIRK on INTEL_SUNRISEPOINT_LP_XHCI
usb: xhci: fix build warning - missing prototype
usb: xhci: dbc: Fixing typo error.
usb: xhci: remove unused member 'parent' in xhci_regset struct
xhci: tegra: Prevent error pointer dereference
USB: serial: option: add Telit ME910 ECM composition
usb: core: Replace hardcoded check with inline function from usb.h
usb: core: skip interfaces disabled in devicetree
usb: typec: mux: remove redundant check on variable match
...
The APM X-Gene platform is now maintained by folks from Ampere
computing that took over the product line a while ago, this gets
reflected in the MAINTAINERS file.
Cleanups continue on the older mach-davinci and mach-pxa platform,
to get them to be more like the modern ones. For pxa, we
now remove the Raumfeld platform code as it now works with
device tree based booting.
i.MX adds a couple new features for the i.MX7ULP SoC
Mediatek gains support for a new SoC: MT7629 is a new wireless
router platform, following MT7623.
Aside from those, there are the usual minor cleanups and bugfixes
across several platforms.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=vxwd
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC platform updates from Arnd Bergmann:
"The APM X-Gene platform is now maintained by folks from Ampere
computing that took over the product line a while ago, this gets
reflected in the MAINTAINERS file.
Cleanups continue on the older mach-davinci and mach-pxa platform, to
get them to be more like the modern ones. For pxa, we now remove the
Raumfeld platform code as it now works with device tree based booting.
i.MX adds a couple new features for the i.MX7ULP SoC
Mediatek gains support for a new SoC: MT7629 is a new wireless router
platform, following MT7623.
Aside from those, there are the usual minor cleanups and bugfixes
across several platforms"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (49 commits)
MAINTAINERS: Update Ampere email address
usb: ohci-da8xx: remove unused callbacks from platform data
ARM: davinci: da830-evm: remove legacy usb helpers
ARM: davinci: omapl138-hawk: remove legacy usb helpers
usb: ohci-da8xx: add vbus and overcurrent gpios
ARM: davinci: da830-evm: use gpio lookup entries for usb gpios
ARM: davinci: omapl138-hawk: use gpio lookup entries for usb gpios
usb: ohci-da8xx: add a helper pointer to &pdev->dev
usb: ohci-da8xx: add a new line after local variables
arm64: meson: enable g12a clock controller
MAINTAINERS: Add entry for uDPU board
ARM: davinci: da850-evm: use GPIO hogs instead of the legacy API
arm: mediatek: add MT7629 smp bring up code
Revert "ARM: mediatek: add MT7623a smp bringup code"
dt-bindings: soc: fix typo of MT8173 power dt-bindings
ARM: meson: remove COMMON_CLK_AMLOGIC selection
arm64: meson: remove COMMON_CLK_AMLOGIC selection
ARM: lpc32xx: remove platform data of ARM PL111 LCD controller
ARM: lpc32xx: remove platform data of ARM PL180 SD/MMC controller
ARM: lpc32xx: Use kmemdup to replace duplicating its implementation
...
This static inline is unnecessary and can be removed
by using the vsprintf %ph extension.
This reduces overall object size by more than 2K.
Reported-by: Louis Taylor <louis@kragniz.eu>
Signed-off-by: Joe Perches <joe@perches.com>
Reviewed-by: Louis Taylor <louis@kragniz.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make the default autosuspend delay configurable at build time.
This is useful for systems that require a non-standard value as
it avoids relying on the command line being properly set.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Refactor the code in charge of looking up the USB PHY when no platdata
is provided. Attempt to get a generic USB PHY first, then look for a
legacy USB PHY through device-tree and finally get any registered PHY
with the correct type.
This way, only a single USB PHY is obtained and the flow is easier to
understand and follow.
All error pointers (except for EPROBE_DEFER) are considered as PHY
not found.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to the chipidea driver bindings, the USB PHY is specified via
the "phys" phandle node. However, this only takes effect for USB PHYs
that use the common PHY framework. For legacy USB PHYs, a simple lookup
based on the USB PHY type is done instead.
This does not play out well when more than one USB PHY is registered,
since the first registered PHY matching the type will always be
returned regardless of what the driver was bound to.
Fix this by looking up the PHY based on the "phys" phandle node.
Although generic PHYs are rather matched by their "phys-name" and not
the "phys" phandle directly, there is no helper for similar lookup on
legacy PHYs and it's probably not worth the effort to add it.
When no legacy USB PHY is found by phandle, fallback to grabbing any
registered USB2 PHY. This ensures backward compatibility if some users
were actually relying on this mechanism.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support to set the power line polarity for i.MX SoCs.
To let the USB controller control the power it may be necessary to
configure the polarity of the power line. So far the polarity was
configured by Bootloader or alternatively the power line was muxed
as gpio and driven by a regulator.
Also make use of of_property_read_bool.
Signed-off-by: Philipp Puschmann <philipp.puschmann@emlix.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Those 2 headers files are not required now.
Signed-off-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ChipIdea's platform device need to be unregistered on Tegra's driver
module removal.
Fixes: dfebb5f43a ("usb: chipidea: Add support for Tegra20/30/114/124")
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Peter Chen <peter.chen@nxp.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hedberg says:
====================
Here's the main bluetooth-next pull request for the 5.1 kernel.
- Fixes & improvements to mediatek, hci_qca, btrtl, and btmrvl HCI drivers
- Fixes to parsing invalid L2CAP config option sizes
- Locking fix to bt_accept_enqueue()
- Add support for new Marvel sd8977 chipset
- Various other smaller fixes & cleanups
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
On Chrome OS we want to use USBguard to potentially limit access to USB
devices based on policy. We however to do not want to wait for userspace to
come up before initializing fixed USB devices to not regress our boot
times.
This patch adds option to instruct the kernel to only authorize devices
connected to the internal ports. Previously we could either authorize
all or none (or, by default, we'd only authorize wired devices).
The behavior is controlled via usbcore.authorized_default command line
option.
Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are a couple of new device ids for 5.1-rc1.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
iHQEABYIAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCXG7PogAKCRALxc3C7H1l
CLtbAP9N7qnHiOflSg8sK3E4hBI5ZaVKQuJwObEOMJY+s6jeYwD1E3sbyWKGHu+2
R8Px/FbKC3JWMUIhO7bVlyvsQDcQAA==
=hG64
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-5.1-rc1-2' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial fixes for 5.1-rc1
Here are a couple of new device ids for 5.1-rc1.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
* tag 'usb-serial-5.1-rc1-2' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: ftdi_sio: add ID for Hjelmslund Electronics USB485
USB: serial: cp210x: add ID for Ingenico 3070
Here are the USB-serial updates for 5.1-rc1, including:
- support for the last three GPIOs on cp2102n devices
- gpio support for cp2104
- support for using cp210x gpios with autosuspend
- proper error handling for unsupported cp2105 line speeds
Included is also a new modem device id.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCXG7M3AAKCRALxc3C7H1l
CBUpAQD/N1G1G38alGS0zwn/u9krsVyLm5Y1gK8MWXvpkcGBXwEAoSYrMjoRAAdR
Ks4rQdSyYonbE3zENXp5d3beCRM4pQY=
=GQ5N
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-5.1-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial updates for 5.1-rc1
Here are the USB-serial updates for 5.1-rc1, including:
- support for the last three GPIOs on cp2102n devices
- gpio support for cp2104
- support for using cp210x gpios with autosuspend
- proper error handling for unsupported cp2105 line speeds
Included is also a new modem device id.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
* tag 'usb-serial-5.1-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: option: add Telit ME910 ECM composition
USB: serial: cp210x: fix GPIO in autosuspend
USB: serial: cp210x: add minimum baud rate for CP2105 SCI
USB: serial: cp210x: add GPIO support for CP2104
USB: serial: cp210x: support all gpios on CP2102N QFN28 package
Commit 1a2f474d32 handles block _reads_ separately with plain-I2C
adapters, but the problem described with regmap-i2c not handling
SMBus block transfers (i.e. read and writes) correctly also exists
with writes.
As workaround, this patch adds a block write function the same way
1a2f474d32 adds a block read function.
Fixes: 1a2f474d32 ("usb: typec: tps6598x: handle block reads separately with plain-I2C adapters")
Fixes: 0a4c005bd1 ("usb: typec: driver for TI TPS6598x USB Power Delivery controllers")
Signed-off-by: Nikolaus Voss <nikolaus.voss@loewensteinmedical.de>
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
