This patch adds support for 405GPr processors with optional
new mode strapping. ibm405gp_fixup_clocks() can now be used
for 405GP and 405GPr CPUs.
This is in preparation of porting the cpci405 platform support
from arch/ppc to arch/powerpc.
This patch also adds ibm405ep_fixup_clocks() to support
405EP CPUs from the boot wrapper.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Currently we have some limitations in the 4xx PCIe driver and can't
support all possible PCIe busses. But the current limits in the
dts file are quite low (only 16 busses per RC). This patch increases
the number to 64 per RC.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Recent DTC versions disallow certain special characters in full paths without
being quoted with {}. That however breaks compatibility with older DTC
versions. Work around this by renaming the CPU nodes for the 4xx files to a
generic node name, and specify the processor type in the model property of the
CPU node.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
The recent changes from Benjamin Herrenschmidt to the ibm_newemac now
make it possible to support other 4xx variants by just defining the
correct properties in the device tree. In this case of the 405EX we
need to define "has-mdio" in the RGMII node and "has-inverted-stacr-oc"
and "has-new-stacr-staopc" in the EMAC node same as on the 440EPx.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This patch adds runtime detection of the 440SPe revision A chips. These
chips are equipped with a slighly different PCIe core and need special/
different initialization. The compatible node is changed to
"plb-pciex-440spe" ("A" and "B" dropped). This is needed for boards that
can be equipped with both PPC revisions like the AMCC Yucca.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This removes a bogus empty "ranges" property in the EBC device node
of the Bamboo board device-tree.
The "ranges" property should be created by the wrapper code when it is
implemented. Until then, remove the empty property since it incorrectly
implies that there is a 1:1 address mapping between the EBC and the OPB.
This also fixes a warning from newer DTCs.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This adds base support for the Katmai board, including PCI-X and
PCI-Express (but no RTC, nvram, etc... yet).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This reworks the boot wrapper library function that probes
the chip clocks. Better separate the base function that is
used on 440GX,SPe,EP,... from the uart fixups as those need
different device-tree path on different processors.
Also, rework the function itself based on the arch/ppc code
from Eugene Surovegin which I find more readable, and which
handles one more bypass case. Also handle the subtle difference
between 440EP/EPx and 440SPe/GX, on the former, PerClk is derived
from the PLB clock while on the later, it's derived from the OPB.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This adds macros to the boot wrapper to access the CPR
registers from the boot wrappers.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
The 4xx bootwrapper occasionally needs to access SPR registers,
this adds mfspr/mtspr wrappers to it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This adds a function to the bootwrapper 4xx library to decode memory
size on 440SPE processors.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This adds the definition of the on-chip OHCI controller to the
Bamboo board's device-tree. This is enough to get it probed and
working, though a separate patch fixing a bug in the OHCI driver
is needed to make it reliable.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This adds the device-tree bits & call to ppc4xx_pci_find_bridges()
to make PCI work on the Bamboo board
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This patch adds base support for the AMCC Taishan 440GX evaluation
board.
Signed-off-by: Hugh Blemings <hugh@blemings.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This wires up the 4xx PCI support & device-tree bits for the
405GP based Walnut platform.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Brings EP405 support to arch/powerpc. The IRQ routing for the CPLD
comes from a device-tree property, PCI is working to the point where
I can see the video card, USB device, and south bridge.
This should work with both EP405 and EP405PC.
I've not totally figured out how IRQs are wired on this hardware
though, thus at this stage, expect only USB interrupts working,
pretty much the same as what arch/ppc did.
Also, the flash, nvram, rtc and temp control still have to be wired.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This wires up the 4xx PCI support & device tree bits for
440GP based Ebony platform.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This patch alters the kernel makefiles to build dtc from the sources
embedded in the previous patch. It also changes the
arch/powerpc/boot/wrapper script to use the embedded dtc, rather than
expecting a copy of dtc already installed on the system.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This incorporates a copy of dtc into the kernel source, in
arch/powerpc/boot/dtc-src. This commit only imports the upstream
sources verbatim, a later commit will actually link it into the kernel
Makefiles and use the embedded code during the kernel build.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Many operations, as currently used in the wrapper, assume they can
pass NULL and have it be treated as the root node. However, libfdt-wrapper
converts NULL to -1, which is only appropriate when searching for nodes,
and will cause an error otherwise.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
fdt_wrapper_create_node passes a variable called offset to offset_devp(),
which uses said parameter to initialize a local variable called offset.
Due to one of the odder aspects of the C language, the result is an
undefined variable, with no error or warning.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Updates the ucc_geth device driver to check the new rx-clock-name and
tx-clock-name properties first. If present, it uses the new function
qe_clock_source() to obtain the clock source. Otherwise, it checks the
deprecated rx-clock and tx-clock properties.
Update the device trees for 832x, 836x, and 8568 to contain the new property
names only.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Verified on mpc866ads. This version has muram and brg nodes added to dts
to get the things work.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Vitaly Bordug <vitb@kernel.crashing.org>
Added aliases nodes for kurobox, 83xx, 85xx, and 86xx platforms.
This included added labels and cell-index properties for serial and
pci nodes.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* Removed address fields in ethernet nodes
* Removed #address-cells, #size-cells from gianfar nodes
* Added cell-index to gianfar and ucc ethernet nodes
* Added enet[0..3] labels
* Renamed compatible node for gianfar mdio to "fsl,gianfar-mdio"
* Removed device_type = "mdio"
The matching for gianfar mdio still supports the old "mdio"/"gianfar" combo
but it is now considered deprecated.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The addition of the aliases node is needed for U-Boot
and, eventually, cuImage, to help locate the proper
nodes reliably when using the libfdt approach.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Now that earlier patches have switched the bootwrapper to using libfdt
for device tree manipulation, this patch removes the now unused
flatdevtree.c and related files.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This incorporates libfdt (from the source embedded in an earlier
commit) into the wrapper.a library used by the bootwrapper. This
includes adding a libfdt_env.h file, which the libfdt sources need in
order to integrate into the bootwrapper environment, and a
libfdt-wrapper.c which provides glue to connect the bootwrapper's
abstract device tree callbacks to the libfdt functions.
In addition, this changes the various wrapper and platform files to
use libfdt functions instead of the older flatdevtree.c library.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This incorporates a copy of dtc libfdt into the kernel source, in
arch/powerpc/boot/libfdt. This only imports the upstream sources
verbatim, later patches are needed to actually link it into the kernel
Makefiles.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There are a few variants of the STACR register that affect more than
just the "AXON" version of EMAC. Replace the current test of various
chip models with tests for generic properties in the device-tree.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
More than just "AXON" version of EMAC RGMII supports MDIO, so replace
the current test with a generic property in the device-tree that
indicates such support.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This adds a 'bootwrapper_install' make target for the powerpc
architecture, which installs the wrapper script, intermediate object
files and device-tree sources for later use.
This will then allow bootable zImages to be created other than in the
context of a kernel build.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
It's possible that the executables which are built as helpers for the
bootwrapper stuff might end up in a different place to the intermediate
object files. Handle that.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
If a .dts file is given to the bootwrapper script without a full path
name, look in a sensible place for it.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The bootwrapper script currently generates an 'otheros.bld' file in
addition to the file specified by the -o option, when asked to build a
wrapper for PS3.
It should do that in the same directory as the output, not the directory
where the wrapper objects are kept (which might potentially not be
writable when the script runs).
Arguably, the 'otheros.bld' ought to be created with the filename
specified as the -o argument. But that's a more intrusive change.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Now the rtc class ds1374 driver has been added, remove the old rtc
driver hookup code, add rtc node to device trees, and turn on the
new driver in the defconfigs.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The interrupt map for the PCI PHB that had the ULI1575 was not correct
on the boards that have it.
* 8544 DS:
- Fix interrupt mask
- Be explicit about use of INTA for on chip peripherals
* 8572 DS/8641 HPCN:
- Fix interrupt mask
- Expand interrupt map for PCI slots to cover all functions
- Be explicit about use of INTA for on chip peripherals
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
correct the reg property, remove duplicate io port entry, whitespace fixes.
Thanks to Peter Van Ackeren for pointing this out.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The ps3 target produces two images, and the binary one is not the
"primary" image that corresponds to the -o flag; thus, it no longer
uses the generic binary flag.
On platforms which do use the binary flag, it no longer produces a
.bin suffix, so that the output file matches what was passed to the -o flag.
This should fix the zImage ln problems for the ps3 target.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Re-order the EMAC interrupts in the walnut.dts file so that they are mapped
correctly.
Signed-off-by: Steve Falco <sfalco at harris.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Add the 'set -e' command to the wrapper script so that if any command
fails then the script will automatically exit
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Allow wrapper script to print verbose progress when the V is set in the
environment.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Add 'fsl,' prefix to 'compatible' property for gpt nodes.
Add 'fsl,' prefix to empty, GPT0 specific 'has-wdt' property.
The fsl, prefix is being added to better match the convention of prefixing
manufacturer specific properties and values with the vendors name.
Signed-off-by: Marian Balakowicz <m8@semihalf.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Fix some device tree omissions that prevented the new EMAC driver from
setting up ethernet on the Bamboo board correctly and update the Bamboo
defconfig.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This patch enables the ibm_newemac driver for the Walnut board. It fixes the
device tree for the walnut board to order the MAL interrupts correctly and
adds the local-mac-address property to the EMAC node. The bootwrapper is also
updated to extract the MAC address from the OpenBIOS offset where it is stored.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
The current bootwrapper fails to set the timebase clock to the CPU clock
which causes the time to increment incorrectly. This fixes it by using the
correct #define for the CPC0_CR1 register.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This adds RGMII support to Sequoia DTS and sets correct phy-mode
for EMACs. According to Sequoia datasheet, both ethernet ports
are connected to RGMII interface, while ZMII is used only for MDIO.
Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Add device tree entries for lite5200b's FEC's PHY.
Signed-off-by: Domen Puncer <domen.puncer@telargo.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This adds a memchr() implementation to the bootwrapper, which will
be needed when libfdt is merged in.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We don't use any CPM devices on these boards, but the muram node on these
chips is different from the 8560, so it's helpful to people working with
custom boards based on these chips.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add '-g' to BOOTCFLAGS if CONFIG_DEBUG_INFO is set.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
DTC now supports "foo","bar" format for lists of strings; use the new
format on the lite5200 device trees.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
1. UCC1's RX_DV pin is 16, not 15;
2. UCC1's phy is at 0x7, not 0x1. Schematics says 0x7, and recent
u-boot also using 0x7.
3. Use gianfar's (eTSEC) mdio bus. This is hardware default setup.
4. tx-clock should be CLK16 (GE125, PB31);
5. phy-connection-type is RGMII-ID;
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
On the majority of 85xx & 86xx we have a register that's ability to
assert HRESET_REQ to reset the board. We refactored that code so it
can be shared between both platforms into fsl_soc.c and removed all
the duplication in each platform directory.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
According to booting-without-of.txt, compatible should be "fsl_spi" and
mode "cpu" or "qe" for the fsl SPI controllers.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The PCI nodes on the MPC8568 dts didn't get moved up to be sibilings of the
SOC node when we did that clean up for some reason. Fix that up and some
minor whitespace and adjusting the size of the soc reg property.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
MPC8568E-MDS have DS1374 chip on the I2C bus, thus let's use it.
This patch also adds #address-cells and #size-cells to the I2C
controllers nodes.
p.s. DS1374 rtc class driver is in the -mm tree, its name is
rtc-rtc-class-driver-for-the-ds1374.patch.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The way the current CPM binding describes available multi-user (a.k.a.
dual-ported) RAM doesn't work well when there are multiple free regions,
and it doesn't work at all if the region doesn't begin at the start of
the muram area (as the hardware needs to be programmed with offsets into
this area). The latter situation can happen with SMC UARTs on CPM2, as its
parameter RAM is relocatable, u-boot puts it at zero, and the kernel doesn't
support moving it.
It is now described with a muram node, similar to QE. The current CPM
binding is sufficiently recent (i.e. never appeared in an official release)
that compatibility with existing device trees is not an issue.
The code supporting the new binding is shared between cpm1 and cpm2, rather
than remain separated. QE should be able to use this code as well, once
minor fixes are made to its device trees.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds cuboot support for MPC7448HPC2 platform.
The cuImage can be used with legacy u-boot without FDT support.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
1. PCI and reset are factored out into pq2.c. I renamed them from m82xx
to pq2 because they won't work on the Integrated Host Processor line of
82xx chips (i.e. 8240, 8245, and such).
2. The PCI PIC, which is nominally board-specific, is used on multiple
boards, and thus is used into pq2ads-pci-pic.c.
3. The new CPM binding is used.
4. General cleanup.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This board is also resold by Freescale under the names
"QUICCStart MPC885 Evaluation System" and "CWH-PPC-885XN-VE".
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
It now uses the new CPM binding and the generic pin/clock functions, and
has assorted fixes and cleanup.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The localbus node is used to describe devices that are connected via a chip
select or similar mechanism. The advantages over placing the devices under
the root node are that it can be probed without probing other random things
under the root, and that the description of which chip select a given device
uses can be used to set up mappings if the firmware failed to do so in a
useful manner.
cuboot-pq2 is updated to match the binding; previously, it called itself
chipselect rather than localbus, and used phandle linkage between the
actual bus node and the control node (the current agreement is to simply use
the fully-qualified address of the control registers, and ignore the overlap
with the IMMR node).
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
fsl_get_immr() uses /soc/ranges to determine the immr.
mpc885_get_clock() transforms a crystal frequency into a system frequency
according to the PLL register settings.
pq2_get_clocks() does the same as the above for the PowerQUICC II,
except that it produces several different clocks.
The mpc8xx/pq2 set_clocks() functions modify common properties in
the device tree based on the given clock data.
The mpc885/pq2 fixup_clocks() functions call get_clocks(), and
pass the results to set_clocks().
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Consensus was reached to put PCI nodes at the root of the tree (and not
under /soc), but the phandle to a control node was rejected in favor of
simply not worrying about /pci/reg overlapping /soc/ranges.
This updates cuboot-82xx to not look for the phandle.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
As suggested by David Gibson, now that we have a separate node
for the baud rate generators, it's better to use the standard
clock-frequency property than a cpm-node-level fsl,brg-frequency
property.
This patch updates existing places where fsl,brg-frequency is
used.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Allows the bootwrapper to use the uartlite device for console output.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Pass the appropriate -mcpu flag to the treeboot-walnut.o object to prevent
some toolchains from erroring out with unknown opcodes
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This is a library that board code can use to extract information from the
PlanetCore configuration keys. PlanetCore is used on various boards from
Embedded Planet.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This allows callers to set addresses one at a time when that would be more
convenient.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Call gunzip_partial to calculate the remaining length and copy the
data to the user buffer. This makes it shorter and reduces
duplication.
Signed-off-by: Milton Miller <miltonm@bga.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Record the number of header bytes skipped in the total bytes read field.
This is needed for the initramfs parsing code to find the end of the zip file.
Signed-off-by: Milton Miller <miltonm@bga.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Setup dr_mode for USB-DR to peripheral as the default (host mode) doesn't make
much sense for the mini-AB connector on the ITX board.
Peripheral mode is preferable to OTG as the fsl_usb2_udc.c driver doesn't yet
properly support it.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
cuImage needs to know the logical index of the ethernet devices in order
to assign mac addresses. This adds the needed properties.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
CC: Scott Wood <scottwood@freescale.com>
CC: Kumar Gala <galak@kernel.crashing.org>
CC: Timur Tabi <timur@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
According to PowerPC 440EPx documentation,
MAL0 is comprised of four channels (two transmit and two receive).
Each channel is dedicated to one of two EMAC cores.
This patch fixes Sequoia DTS MAL0 entry and EMAC entries,
assigning correct channel numbers to EMACs.
Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
A new binding for flash devices was recently introduced. This updates the
Sequoia DTS to use the new binding and enabled MTD in the defconfig.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Stefan Roese <sr@denx.de>
A new binding for flash devices was recently introduced. This updates the
Walnut DTS to use the new binding.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Add a cuboot wrapper for the Bamboo board. Additionally, we enable MAC
address fixups for both cuboot and treeboot.
This also removes some obsoleted linker declarations that have been
moved into ops.h
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Enabled using SPI controller on the MPC832x RDB board. We currently use
a modalias of "spidev" as a place holder (replace with "mmc_spie") until
the mmc_spi driver support is merged in.
This gets us the ability to test SPI until then.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Updated the device trees to have the PCI nodes be at the same level as
the SOC node. This is to make it so that the SOC nodes children address
space is just on chip registers and not other bus memory as well.
Also, for PCIe nodes added a P2P bridge to handle the virtual P2P bridge
that exists in the PHB.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Removed the following cruft from .dts files:
* 32-bit in cpu node -- doesn't exist in any spec and not used by kernel
* removed built-in (chrp legacy)
* Removed #interrupt-cells in places they don't need to be set
* Fixed ranges on lite5200*
* Removed clock-frequency from i8259 pic node, not sure where this came from
* Removed big-endian from i8259 pic nodes, this was just bogus
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Added basic board port for MPC8572 DS reference platform that is
similiar to the MPC8544/33 DS reference platform in uniprocessor mode.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
1. Fix RTC type - it is a rs5c372a, not rs5c372b
2. Configure both UART interrupts edge-triggered
3. Add a license header to ls_uart.c
4. Check for running on linkstation in a late_initcall() function. Needed
for multiplatform builds, even though linkstation doesn't support them
yet
5. Remove unneeded #include from linkstation.c
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This replaces the binding for flash chips in booting-without-of.txt
with an clarified and improved version. It also makes
drivers/mtd/maps/physmap_of.c recognize this new binding. Finally it
revises the Ebony device tree source to use the new binding as an
example.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Segher Boessenkool <segher@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Some firmwares (such as PlanetCore) only provide a base MAC address, and
expect the kernel to set certain bits to generate the addresses for the
other ports. As such, MAC addresses are generated that may not correspond
to actual hardware.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This will be used by the PlanetCore firmware support to construct
a linux,stdout-path from the serial node that it finds.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This will be needed by PlanetCore firmware support.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
1. ft_create_node was returning the internal pointer rather than a phandle.
2. ft_find_device_rel was treating a "top" phandle of NULL as an error,
rather than as the root of the tree. The old, absolute ft_find_device
is removed, and the relative version is renamed to ft_find_device().
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently the bootwrapper has implementations of strchr() and
strncmp(), but they're inlines in flatdevtree_env.h, rather than in
string.S with all the rest of the string functions. This moves
them to string.S.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Device tree source file for the PPC405 Walnut evaluation board.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
The patch below removes the dtc incantation instructions from the
in-kernel DTS files. It's not needed, and is prone to being
out-of-date most of the time.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
This allows booting on legacy, non-device-tree aware versions of U-boot.
It also fixes up the hardware to match the PCI and chipselect information
in the device tree, as u-boot is inconsistent in setting these up
correctly (or at all).
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This allows booting on legacy, non-device-tree aware versions of U-boot.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Most of these were previously used by numerous C files and
redeclared in each one.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This serial port is used on all 8xx, many 82xx, and some 85xx chips.
The driver requires that the port has already been set up by the firmware
and/or platform code.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
1. Search the entire compatible list for serial devices.
The serial code previously did a simple strcmp on the compatible
node; this fails when the match string is not the first compatible
listed. Use dt_is_compatible() instead.
2. Don't call serial_edit_cmdline if getc isn't defined.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
U-boots more recent than when ppcboot.h was forked allow the board config
file to enable additional ethernet ports explicitly, rather than
using a hardcoded list of targets. This allows bootwrapper platform
files to do the same.
Fortunately, nothing after the ethernet addresses is of interest to
cuboot platforms, so the inevitable mismatches won't be too catastrophic.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Also, include types.h from io.h, so callers don't have to.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This can be used rather than doing a simple strcmp, which will fail to
handle multiple compatible entries.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
1. The check whether ranges fits in the buffer was using elements rather
than bytes.
2. Empty ranges were not properly treated as transparent, and missing
ranges were treated as transparent.
3. The loop terminated when translating from the root rather than to. Once
bug #2 was fixed, it failed due to a missing ranges in the root node.
4. In decoding the ranges property, the #size-cells used was that of
the parent, not the child.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This lets udelay() work properly on platforms which use dt_fixup_cpu_clocks.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
All cuImage types are ignored, as well as preprocessed .lds files,
and the forthcoming zImage.bin files and embedded planet board images.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add a bootwrapper for the AMCC 440EP Bamboo Eval board. This also adds a
common fixup_clock function for all 440EP(x) chips.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Make the fixup_memsize function common for all of 4xx as several chips share
the same SDRAM controller. Also add functions to reset 40x chips and quiesce
the ethernet.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Rename the 44x.c wrapper file to 4xx.c. This will allow us to add common
functions in a single file that can be shared across all of 4xx.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
The interrupt routing in the device trees for the ULI M1575 was
inproperly using the interrupt line field as pci function. Fixed
up the device tree's to actual conform for to specification and
changed the interrupt mapping code so it just uses a static mapping
setup as follows:
PIRQA - IRQ9
PIRQB - IRQ10
PIRQC - IRQ11
PIRQD - IRQ12
USB 1.1 OCHI (1c.0) - IRQ12
USB 1.1 OCHI (1c.1) - IRQ9
USB 1.1 OCHI (1c.2) - IRQ10
USB 1.1 ECHI (1c.3) - IRQ11
LAN (1b.0) - IRQ6
AC97 (1d.0) - IRQ6
Modem (1d.1) - IRQ6
HD Audio (1d.2) - IRQ6
SATA (1f.1) - IRQ5
SMB (1e.1) - IRQ7
PMU (1e.2) - IRQ7
PATA (1f.0) - IRQ14/15
Took the oppurtunity to refactor the code into a single file so we
don't have to duplicate these fixes on the two current boards in the
tree and several forth coming boards that will also need the code.
Fixed RTC support that requires a dummy memory read on the P2P bridge
to unlock the RTC and setup the default of the RTC alarm registers to
match with a basic x86 style CMOS RTC.
Moved code that poked ISA registers to a FIXUP_FINAL quirk to ensure
the PCI IO space has been setup properly before we start poking ISA
registers at random locations.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch contains a handful of small fixes to allow the Ebony's
flash to be exposed as MTD devices via the physmap_of driver.
Specifically it:
- Makes a small addition to the device tree and zImage wrapper
to record the correct address for the flash in the device tree based
on the board switches as reported via an FPGA register.
- Prohibits building the old hard-coded "Ebony" flash map on
arch/powerpc kernels, in favour of using physmap_of's device tree
based approach.
- Enables MTD and physmap_of in the Ebony defconfig.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
AFAICT, nobody is using ft_ordered(), and it causes a build warning
to be generated. This patch cleans that up by removing the function
and the commented-out code that calls it.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog: (28 commits)
[WATCHDOG] Fix pcwd_init_module crash
[WATCHDOG] ICH9 support for iTCO_wdt
[WATCHDOG] 631xESB/632xESB support for iTCO_wdt - add all LPC bridges
[WATCHDOG] 631xESB/632xESB support for iTCO_wdt
[WATCHDOG] omap_wdt.c - default error for IOCTL is -ENOTTY
[WATCHDOG] Return value of nonseekable_open
[WATCHDOG] mv64x60_wdt: Rework the timeout register manipulation
[WATCHDOG] mv64x60_wdt: disable watchdog timer when driver is probed
[WATCHDOG] mv64x60_wdt: Support the WDIOF_MAGICCLOSE feature
[WATCHDOG] mv64x60_wdt: Add a module parameter to change nowayout setting
[WATCHDOG] mv64x60_wdt: Add WDIOC_SETOPTIONS ioctl support
[WATCHDOG] mv64x60_wdt: Support for WDIOC_SETTIMEOUT ioctl
[WATCHDOG] mv64x60_wdt: Fix WDIOC_GETTIMEOUT return value
[WATCHDOG] mv64x60_wdt: Check return value of nonseekable_open
[WATCHDOG] mv64x60_wdt: Add arch/powerpc platform support
[WATCHDOG] mv64x60_wdt: Get register address from platform data
[WATCHDOG] mv64x60_wdt: set up platform_device in platform code
[WATCHDOG] ensure mouse and keyboard ignored in w83627hf_wdt
[WATCHDOG] s3c2410_wdt: fixup after arch include moves
[WATCHDOG] git-watchdog-typo
...
This fixes the RTC on linkstation ppc machines again, and updates the
device tree: add rtc nodes on i2c, remove bogus 0-size cache-line
declarations, rename interrupt-controller nodes, remove erroneous
interrupt-parent line, accidentally introduced by a recent patch.
Signed-off-by: G. Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add global-utilities node with has-rstcr on MPC8544 DS and MPC8568 MDS
boards so they are able to reset properly.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix mpc7448hpc2 tsi108 device_type bug.
Wrong device type will break the board startup.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The MPC8544 dts needed to set the new phy-connection-type to rgmii-id
for the Vitesse PHY on the board to work properly.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add support for arch/powerpc, specifically for the prpmc2800 platform.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Added the P2P bridge present on the Arcadia base board and moved the VIA
Southbridge behind the bridge to reflect its actual position in the bus
organization. Added the RTC that's in the VIA Southbridge and expanded
the ranges array for the SOC node to allow proper address translation of
the RTC registers.
Signed-off-by: Randy Vinson <rvinson@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add basic support for the PCIe PHB and enable the ULI bridge.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Updated the 83xx & 85xx device tree PCI related compartible property.
Used the following compatible properties:
PCI "fsl,mpc8349-pci"
PCI "fsl,mpc8540-pci"
PCI-X: "fsl,mpc8540-pcix"
PCIe: "fsl,mpc8548-pcie"
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add 8548 CDS PCI express controller node and PCI-X device node. The current
dts file is suitable for 8548 Rev 2.0 board with Arcadia 3.1.
This kind of board combination is the most popular.
Used the following compatible properties:
PCI "fsl,mpc8540-pci"
PCI-X: "fsl,mpc8540-pcix"
PCIe: "fsl,mpc8548-pcie"
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Rewrite the Freescale PCI code to support PCI on 83xx/85xx/86xx and
PCIe on 85xx/86xx.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The PS3 bootwrapper files use instructions only available on 64-bit CPUs.
Add the code generation directive '.machine "ppc64"' for toolchains
configured for 32-bit CPUs.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The TSEC/eTSEC automatically detect their PHY interface type, unless
the type is RGMII-ID (RGMII with internal delay). In that situation,
it just detects RGMII. In order to fix this, we need to pass in rgmii-id
if that is the connection type.
Signed-off-by: Andy Fleming <afleming@freescale.com>
This simply prevents a build error if no platform is selected.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add support to build the PS3 flash rom image and remove some unneeded
lmb calls.
The PS3's lv1 loader supports loading gzipped binary images from flash
rom to addr zero. The loader enters the image at addr 0x100.
In this implementation a bootwrapper overlay is use to arrange for the
kernel to be loaded to addr zero and to have a suitable bootwrapper
entry at 0x100. To construct the rom image, 0x100 bytes from offset
0x100 in the kernel is copied to the bootwrapper symbol
__system_reset_kernel. The 0x100 bytes at the bootwrapper symbol
__system_reset_overlay is then copied to offset 0x100. At runtime the
bootwrapper program copies the 0x100 bytes at __system_reset_kernel to
addr 0x100.
zImage.ps3 is a wrapped image that contains a flat device tree, an lv1
compatible entry point, and an optional initrd. otheros.bld is the gzip
compresed rom image built from zImage.ps3. otheros.bld is suitable for
programming into the PS3 boot flash memory.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Removed explicit linux,phandle usage. Using references and labels now in PQ
and PQ2 boards currently supported in arch/powerpc.
Signed-off-by: Vitaly Bordug <vitb@kernel.crashing.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Olof Johansson <olof@lixom.net>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Adds support for PowerQuicc on-chip PCMCIA. The driver is implemented as
of_device, so only arch/powerpc stuff is capable to use it, which now implies
only mpc885ads reference board.
To cope with the code that should be hooked inside driver, but is really board
specific (like set_voltage), global structure mpc8xx_pcmcia_ops holds
necessary function pointers that are filled in the BSP code.
[akpm@linux-foundation.org: whitespace diddles]
Signed-off-by: Vitaly Bordug <vitb@kernel.crashing.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Olof Johansson <olof@lixom.net>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The PHY is active-low on the MPC85xx CDS and the 8560 ADS just had
the wrong sense for the internal PCI and CPM interrupts.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Make the interrupt numbers match the OpenPIC spec intead of the
Freescale docs which distinguish between internal and external interrupts.
Now we can use the interrupt number directly to find the register offset
associated with it.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
For the 83xx, 85xx, and 86xx device trees, add a "local-mac-address" property
to every Ethernet node that didn't have one. Add a comment indicating that
the "address" and/or "mac-address" properties are deprecated in DTS files
and will be removed at a later time. Change all MAC address properties to
have a zero MAC address value.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Begin with MPC8548 a new reset control register is added that asserts
HRESET_REQ to board logic.
This register is used for chip reset.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This adds device nodes for the PCI bridges as well as the ISA devices on
the newer revision MPC8641HPCN. It also adds the PCI ranges to the soc
node so that address translation for the ISA devices works properly.
Signed-off-by: Wade Farnsworth <wfarnsworth@mvista.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Remove errata for PCI-e support of Rev 1.0 of MPC8641 since its considered
obselete and is not production level silicon from Freescale.
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Acked-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Commit 2e60161337 split up
arch/powerpc/boot/of.c so that some OF functions can be used on
platforms that don't want to use the overall OF platform boot code.
This is useful on things like PReP which can have an OF implementation
which is useful for debugging output, but inadequate for booting.
However, that commit didn't export quite enough things to make a
usable OF console on a non-OF system. In particular, the device tree
manipulation performed to initialize the OF console code must
explicitly use the OF device tree, rather than the flattened device
tree, even if the system is otherwise booting using a flattened device
tree. This makes it so.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
For the convenience of custom platform code make the powerpc
bootwrapper typdef kernel_entry_t global in scope.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fixes the constantness of the powerpc bootwrapper's console_ops.write
routine. Allows printing of constant strings.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add support for the 'll' (long long) printf qualifier in the powerpc zImage
bootwrapper. This is useful for bootwrapper debugging on 64 bit platforms.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add signed types to the powerpc zImage bootwrapper. These are needed by the
PS3 hcall interface.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Specifying 'console=ttyMM0' on the cmdline for the prmpc2800 is no
longer necessary.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The holly support currently has separate rules to wrap its device tree
with its zImage. This can now be done automatically without the extra
rules so update holly support to use the automatic feature.
Signed-off-by: Mark A. Greer <mgreer@mista.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There are 2 config options that indicate whether the platform being built
has a device tree source file associated with it. Namely,
CONFIG_WANT_DEVICE_TREE and CONFIG_DEVICE_TREE. When CONFIG_WANT_DEVICE_TREE
is 'y' and CONFIG_DEVICE_TREE isn't an empty string, automatically wrap
the specified device tree with the zImage being built.
To achieve this, the 'dts' variable will only be set when the conditions
above are true. The changes to the zImage.initrd.% and zImage.% rules
cause the device tree to be wrapped when 'dts' is set; otherwise, they
will work as they previosly did (i.e., build a zImage with no device tree).
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Being able to selectively wrap a device tree with the zIimage at build
time has been deemed unnecessary, so this removes Makefile support for
that feature.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This fixes some problems with the way the some things
represented in the device tree for the Holly and Taiga boards. This
means changes both to the dts files, and to the code which
instantiates the tsi108 ethernet platform devices based on the device
tree.
- First, and most importantly, the ethernet PHYs are given
with an identical 'reg' property. This reg currently encodes the
accessible register used to initiate mdio interaction with the PHYs,
rather than a meaningful address on the parent bus (mdio in this
case), which is incorrect. Instead we give the address of these
registers as 'reg' in the mdio node itself, and encode the ID of each
phy in their 'reg' propertyies.
- Currently the platform device constructor enables a
workaround in the tsi108 ethernet driver based on the compatible
property of the PHY. This is incorrect, because the workaround in
question is necessary due to the board's wiring of the PHY, not the
model of PHY itself. This patch alters the constructor to instead
enable the workaround based on a new special property in the PHY node.
- The compatible properties on a number of nodes in the device
tree are insufficiently precise. In particular the PHYs give only
"bcm54xx", which is broken, since there are many bcm54xx PHY models,
and they have differences which matter. The mdio had a compatible
property of "tsi-ethernet" identical to the ethernet MAC nodes, which
doesn't make sense. The ethernet, i2c, bridge and PCI nodes were
given only as "tsi-*" which is somewhat inprecise, we replace with
"tsi108-*" in the case of Taiga (which has a TSI108 bridge), and
"tsi109-*", "tsi108-*" in the case of Holly (which has a TSI109
bridge).
- We remove some "model" properties from the ethernets on
Taiga board which were neither useful nor adequately precise.
- On Holly we change to using a dtc label instead of a full
path to reference the MPIC node, which makes the dts a little more
readable.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently, the Holly device tree includes a bootargs property in
/chosen, which gives a commandline. This is somewhat inconvenient,
because it means an alternative default command line can't be given in
the kernel config - the value obtained from the dts via the
bootwrapper will always override CONFIG_CMDLINE.
This removes the command line from the dts, and instead puts the
same command line as a default in holly_defconfig.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The various cuboot platforms (i.e. pre-device tree aware u-boot for
83xx, 85xx and Ebony) share a certain amount of code for parsing the
boot parameters. To a certain extent that's inevitable, since they
platforms have different definitions of the bd_t structure. However,
with some macro work and a helper function, this patch improves the
situation a bit.
In the process, this fixes a bug on Ebony, which was incorrectly
handling the parameters passed form u-boot for the command line (the
bug was copied from 83xx and 85xx which have subsequently been fixed).
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In the device tree for Ebony, the 'ranges' property in the node for
the EBC bridge shows the mappings from the chip select / address lines
actually used for the EBC peripherals into the address space of the
OPB. At present, these mappings are hardcoded in ebony.dts for the
mappings set up by the OpenBIOS firmware when it configures the EBC
bridge.
This replaces the hardcoded mappings with code in the zImage to
read the EBC configuration registers and create an appropriate ranges
property based on them. This should make the zImage and kernel more
robust to changes in firmware configuration. In particular, some of
the Ebony's DIP switches can change the effective address of the Flash
and other peripherals in OPB space. With this patch, the kernel will
be able to cope with at least some of the possible variations.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The ebony_exit() function which resets the Ebony board should in fact
be common to most if not all 44x boards. This moves the function out
into 44x.c, renaming it, so it can be used by other 44x platforms.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently, all OF-related code in the bootloader is contained in of.c.
of.c also provides the platform specific things necessary to boot on
an OF platform.
However, there are platforms (such as PReP) which can include an OF
implementation, but are not bootable as pure OF systems. For use by
such platforms, this patch splits out the low-level parts of the OF
code (call_prom() and various wrappers thereof) into a new oflib.c
file. In addition, the code related to bootwrapper console output via
OF are moved to a new ofconsole.c file. Both these files are included
in the wrapper.a library where they can be used by both full-OF and
partial OF platforms.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The COFF zImage (for booting oldworld powermacs) wasn't being built
correctly because the procedure descriptor in crt0.S for the zImage
entry point wasn't declared as .globl, and therefore wasn't getting
pulled in from wrapper.a by the linker. This adds the necessary
.globl statement.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Commit 9da82a6dee inadvertently
removed the platform override for zImage.coff to be generated
with pmaccoff. Rather than add a special makefile rule,
change the platform for which the wrapper platform uses
the special rules.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In the bootwrapper code for powerpc, we include HOSTCFLAGS into the
BOOTCFLAGS used for building the zImage wrapper code. Since the
wrapper code is not host code, this makes no sense. This patch
removes the use of HOSTCFLAGS here, instead including directly into
BOOTCFLAGS those flags from the normal kernel CFLAGS which also make
sense in the bootwrapper code.
In particular, this makes the bootwrapper use -msoft-float, preventing
the compiler from generating floating point instructions. Previously,
under some circumstances the compiler could generate floating point
instructions in the bootwrapper which would cause exceptions on
embedded CPUS which don't have floating point support.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This zImage is really just the stripped vmlinux, but it means that there
is one less special case for iSeries and also that the zImages will be
built for a combined kernel build that happens to include iSeries.
This zImage boots fine on legacy iSeries.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The recent addition of assembler flags for 44x.c and ebony.c in the
bootwrapper to make them compile on certain toolchains was not correct
and could break other platforms. This patch switches to using a
compiler flag instead, which implies the appropriate assembler flag,
and also stops the compiler itself generating instructions which are
invalid for the platform in question.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Segher Boessenkool <segher@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Unbreak lite5200 dts, which were broken by
5c1992f833
Signed-off-by: Domen Puncer <domen.puncer@telargo.com>
Acked-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
As a result of compiling all of the wrapper files for every platform
now, the kernel build can fail for toolchains that don't support various
op codes by default. An example of this building a 7xx platform with
the ELD4.0 toolchain, is below:
/tmp/ccYjhJoL.s: Assembler messages:
/tmp/ccYjhJoL.s:42: Error: Unrecognized opcode: `mtdcr'
/tmp/ccYjhJoL.s:43: Error: Unrecognized opcode: `mfdcr'
make[1]: *** [arch/powerpc/boot/44x.o] Error 1
The following patch introduces additional CFLAGS for the 4xx specific
files and fixes the kernel compile.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Not every sed understands \+ so use the more portable * instead.
Signed-off-by: Segher Boessenkool <segher@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch corrects a number of minor errors in the Ebony device tree:
- Missing (given as 0) cache sizes are added to the CPU node
- device_type properties are removed from nodes which don't
have a reasonably well defined device_type binding. This does require
a very small code change to locate the busses to be probed for
of_platform devices by 'compatible' instead of 'device_type'.
- A node is added for the SRAM controller
- The unit address of the small-flash node is adjusted to
correctly reflect the reg property.
- device_type values for the MAL and ZMII are updated to
reflected more up-to-date versions of the binding.
- An incorrect offset in the partition map for the large-flash
node is corrected.
- Some redundant values, already commented out are removed
entirely.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
At present attempting to build treeImage.initrd.* boot images will
fail, because make will select the treeImage.% rule which also matches
instead of the correct and more specific treeImage.initrd.% rule.
This patch corrects the problem by listing the more specific rule
first.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
ft_set_prop() from flatdevtree.c in the zImage wrapper will either
replace an existing property in the flat device tree, or add a new
property definiion if the given property isn't present.
However, when adding properties, it adds the property definition
immediately before the node's END_NODE tag, potentially after any
subnode definitions for the node. This confuses the kernel flat tree
parser in prom.c which assumes that all property definitions for a
node come before all subnode definitions.
This patch corrects ft_set_prop() so that it adds new properties
before the first subnode, instead of before the END_NODE tag.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Scott Wood <scottwood@freescale.com>
Acked-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Remove explicit phandles and move to using references that autogenerate the
phandles when needed.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Adding memory-controller and l2-cache-controller entries to be used by EDAC
as of_devices for MPC8541 CDS, MPC8544 DS, MPC8555 CDS, and MPC8568 MDS.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Adding memory-controller and l2-cache-controller entries to be used by EDAC
as of_devices for MPC8540 ADS, MPC8548 CDS, and MPC8560 ADS.
Also fixed up the size of the PCI node on MPC8560 ADS.
Signed-off-by: Dave Jiang <djiang@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The Motorola PrPMC280 and PrPMC2800 processor modules sit on an F101 or
PrPMC2800 baseboard, respectively. There are several variants of each
type of processor module which can have different amounts of memory,
amounts of FLASH, cpu frequencies, and an mv64360 or an mv64362.
The bootwrapper code for that platform reads VPD from an I2C EEPROM
to determine the processor module variant. From the variant, the
amount of memory, etc. is determined and the device tree is updated
accordingly. If the variant cannot be determined (e.g., corrupted
VPD or a previously unknown variant), the property values already
in the device tree are used.
Also, the firmware for those platforms does not completely configure
the mv64x60 host bridge so that configuration is done here.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add the device tree source file for the prpmc2800 line of processor PMCs.
Several of the property values are updated by the bootwrapper but sane
defaults have been chosen in case the bootwrapper can't determine the
exact processor board variant. The defaults should allow the kernel
to boot despite having non-optimal device tree property values.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Some platforms support a variety processor modules with no method of
determining which exact processor module is being used except by
examining Vital Product Data (VPD). The modules may have different
amounts of memory, clock frequencies, etc. so reading the VPD becomes
necessary to correctly set properties in the device tree before its
passed to the kernel.
Often the VPD is stored in I2C EEPROMs so an I2C driver becomes necessary.
This I2C driver is for the I2C controller that's embedded on the Marvel
mv64x60 line of host bridges.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The bootwrapper requires a serial driver to allow cmdline editing
and information reporting on the console. This driver is required
by platforms that boot a zImage and use the MPSC for the console.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The mv64x60 host bridge has many windows between its various components
(cpu, system memory, ethernet ctlr, MPSC, DMA ctlr, PCI MEM, PCI I/O).
Unfortunately, the firmware on some of mv64x60-based platforms do not
properly or completely configure those windows (e.g., MPSC->system memory
windows not configured or CPU->PCI MEM space not configured).
So, the missing configuration needs to be done in either the bootwrapper
or in the kernel. To keep the kernel as clean as possible, it is done
in the bootwrapper. Note that I/O controller configuration is NOT being
done, its only the windows to allow the I/O controllers and other components
to access memory, etc. that is being done--drivers assume that their
controllers can already access system memory).
Table of routines and the windows they configure:
mv64x60_config_ctlr_windows() ENET->System Memory
MPSC->System Memory
IDMA->System Memory
mv64x60_config_pci_windows() PCI MEM->System Memory
PCI I/O->Bridge's Registers
mv64x60_config_cpu2pci_window() CPU->PCI MEM
CPU->PCI I/O
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add 'zImage.dts' and 'zImage.dts_initrd' build rules that automatically
compile and wrap a dts file from arch/powerpc/boot/dts into the zImage file.
The resulting zImage will be arch/powerpc/boot/zImage.dts.<platform> and
arch/powerpc/boot/zImage.dts_initrd.<platform>, respectively.
Having separate rules allows the user to choose whether to include a device
tree--and which device tree--at build time. This is useful when one Makefile
target builds a zImage that runs on several platforms except for differing
device trees. By just setting CONFIG_DEVICE_TREE and running "make zImage.dts"
the exact zImage you want is built without Makefile bloat or manually running
the wrapper script.
The dts file is expected to be arch/powerpc/boot/dts/$(CONFIG_DEVICE_TREE)
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The boot wrapper platform init code on 83xx and 85xx using the cuboot
platform type was incorrectly assuming that u-boot supplied the size
of the initrd, whereas it actually supplies the end address. This
fixes it.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The MPC834x_MDS device tree's PCI non-prefetchable MMIO range was
specified incorrectly. Both the local and bus addresses start at
0x90000000.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The MPC832x_MDS device tree's PCI non-prefetchable MMIO range was
specified incorrectly. Both the local and bus addresses start at
0x90000000.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This adds platform support code for the Ebony (440GP) evaluation
board. This includes both code in arch/powerpc/platforms/44x for
board initialization, and zImage wrapper code to correctly tweak the
flattened device tree based on information from the firmware. The
zImage supports both IBM OpenBIOS (aka "treeboot") and old versions of
uboot which don't support a flattened device tree.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add a device tree for the Ebony evaluation board (440GP based). This
tree is not complete or finalized. This tree needs a version of dtc
recent enough to include reference-to-labels to process.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add fsl-i2c to mpc5200 i2c node in device tree, and enable FSL_SOC.
Tested to work with built-in eeprom on lite5200b.
Signed-off-by: Domen Puncer <domen.puncer@telargo.com>
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch fixes a couple of missing dependencies in
arch/powerpc/boot/Makefile. First, it ensures that the zlib.h header
is linked in before attempting to build gunzip_util.o, as it is,
building gunzip_util.o usually works, but not always depending on make
order.
Second, it makes the final images which are built using a dts
dependent on that dts, so the image will be correctly rebuilt if the
dts changes. This in turn requires fixing the definition of the dts
variable. CONFIG_DEVICE_TREE from Kconfig will have quotes around it,
which don't matter when passing the variable to a shell, but which
need to be removed when incorporating it into a filename for make's
use.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This allows the zImage target to once again be used to build
all supported image types, rather than requiring an explicit
"make uImage" to avoid failing to create an unneeded cuImage.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch makes a few small cleanups to the cuboot code.
- It removes the double layered selection of images, via
cuboot-plat-y, instead having the cuboot platforms directly select a
suitable image-y (this changes the name of the final cuboot image from
plain cuImage to cuImage.<platform>).
- Factors out some code in the wrapper that's potentially
useful to platforms other than uboot.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
phy-connection-type now supersedes the interface property.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
dt_xlate_reg() looks up the 'reg' property in the specified node
to get the address and size to translate. Add dt_xlate_addr()
which is passed in the address and size to translate.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
A usage of CONFIG_DEVICE_TREE got accidentally truncated; this
fix allows out-of-tree dts files to work.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The uppermost part of memory is where u-boot puts the stack, so don't
include that in the heap. It's not currently causing problems, as the
current code allocates from the bottom of the heap, but this will keep
things from potentially breaking if a future implementation were to
allocate from the top.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This fixes a few bugs in how dt_xlate_reg() handles address arrays:
1. copy_val() was copying into the wrong end of the array, resulting
in random stack garbage at the other end.
2. dt_xlate_reg() was getting the result from the wrong end of the array.
3. add_reg() and sub_reg() were treating the arrays as
little-endian rather than big-endian.
4. add_reg() only returned an error on a carry out of the entire
array, rather than out of the naddr portion.
5. The requested reg resource was checked to see if it exceeded
the size of the reg property, but not to see if it exceeded the
size of the buffer.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Change the error message in gunzip_exactly to be more verbose.
Besides the identifier being unrelated to the current function name,
the user had no indication if the corruption was near the beginning
or the end.
Signed-off-by: Milton Miller <miltonm@bga.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
make help on powerpc says make install is available.
But it failed due to no rule to make install.
This patch enables make install to work.
Signed-off-by: Akinobu Mita <mita@fixstars.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Use `unsigned long' for malloc sizes, to match common practice and types used
by most callers and callees.
Also use `unsigned long' for integers representing pointers in simple_alloc.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@eu.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds cuboot support for MPC83xx platforms.
A device tree used with this must have linux,stdout-path in /chosen and
linux,network-index in any network device nodes that need mac addresses
assigned.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This file describes the bd_t struct, which is used by old versions of
U-boot to pass information to the kernel. Platform code that needs to
interoperate with such firmware can use this; it should not be used for
anything new.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The cuImage target will build a uImage with bootwrapper code and a device
tree. The default device tree and platform file are determined by the
kernel configuration.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Commit 79c8541924 introduced code to move
the initrd if it was in a place where it would get overwritten by the
kernel image. Unfortunately this exposed the fact that the code that
checks whether the values passed in r3 and r4 are intended to indicate
the start address and size of an initrd image was not as thorough as the
kernel's checks. The symptom is that on OF-based platforms, the
bootwrapper can cause an exception which causes the system to drop back
into OF.
Previously it didn't matter so much if the code incorrectly thought that
there was an initrd, since the values for start and size were just passed
through to the kernel. Now the bootwrapper needs to apply the same checks
as the kernel since it is now using the initrd data itself (in the process
of copying it if necessary). This adds the code to do that.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Our kernels put everything in the first load segment, and we read that.
Instead of decompressing to the end of the gzip stream or supplied image
and hoping we get it all, decompress the expected size and complain if
it is not available.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Commit a9903811bf missed two uses of the
the .gz suffix in the wrapper script and didn't clean the additonal
possibly cached files.
Signed-off-by: Milton Miller <miltonm@bga.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
crt0.S had provisions to provide run address relocaton to got2 and
cache flush, but not on the bss clear or stack pointer load. Apply
the same fixup for them.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The ELF parsing routines local to arch/powerpc/boot/main.c are useful
to other callers therefore move them to their own file.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
dt_xlate_reg() uses the ranges properties of a node's parentage to find
the absolute physical address of the node's registers.
The ns16550 driver uses this when no virtual-reg property is found.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This cleans up how the zImage code manipulates the kernel
command line. Notable improvements from the old handling:
- Command line manipulation is consolidated into a new
prep_cmdline() function, rather than being scattered across start()
and some helper functions
- Less stack space use: we use just a single global command
line buffer, which can be initialized by an external tool as before,
we no longer need another command line sized buffer on the stack.
- Easier to support platforms whose firmware passes a
commandline, but not a device tree. Platform code can now point new
loader_info fields to the firmware's command line, rather than having
to do early manipulation of the /chosen bootargs property which may
then be rewritten again by the core.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds a library of useful device tree manipulation functions
to the zImage library, for use by platform code. These functions are
based on the hooks already in dt_ops, so they're not dependent on a
particular device tree implementation. This patch also slightly
streamlines the code in main.c using these new functions.
This is a consolidation of my work in this area with Scott Wood's
patches to a very similar end.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch provides the basic MPC8544 DS platform code and config.
Follow-up patches will add peripherals such as PCI and SATA.
Signed-off-by: Xianghua Xiao <x.xiao@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add support for the MPC8323E Reference Development Board (RDB). The board
is a mini-ITX reference board with 64M DDR2, 16M flash, USB, PCI,
10/100 ethernet, serial, and phone ports.
Signed-off-by: Michael Barkowski <michael.barkowski@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds a reg.h to the zImage code, with common definitions
for accessing system registers. For now, this includes functions for
retrieving the PVR and the stack pointer. This patch then uses the
new reg.h to let start() display the running stack address without
having to explicitly pass the stack as a parameter from the asm code.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds the correct attributes to the zImage's versions of
printf to make gcc generate format string mismatch warnings. It also
corrects several minor problems with format strings in the zImage thus
discovered.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Before the plethora of platforms gets any worse, establish a common
rule to invoke the wrapper for any platform. Add arguments to
the rule for initrd, dts, dtb, etc. Show example usage with initrd.
Create default rules for zImage, and zImage.initrd. initrd targets
depend on the ramdisk file.
Don't consider targets for zImage.initrd that are targets for zImage.
This means uImage is no longer considered a target for zImage.initrd.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
