FPGA offset in NOR flash was converted incorrectly when switching from
64M to 4M flash.
Signed-off-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Added support for the new at24 eeprom driver.
Documented a new fpga section, the DMA scatter gather list.
Removed index from i2c. No longer needed.
Fixed the leds section.
Signed-off-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
from include/asm-powerpc. This is the result of a
mkdir arch/powerpc/include/asm
git mv include/asm-powerpc/* arch/powerpc/include/asm
Followed by a few documentation/comment fixups and a couple of places
where <asm-powepc/...> was being used explicitly. Of the latter only
one was outside the arch code and it is a driver only built for powerpc.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
add simple-bus compatible property to soc nodes for 83xx/85xx platforms
that were missing them. Add same to platform probe code.
This fixes SoC device drivers (such as talitos) to succeed in matching
devices present in the soc node.
also update mpc836x_rdk dts to new SEC bindings (overlooked in commit
3fd4473: powerpc/fsl: update crypto node definition and device tree
instances).
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
For C code spaces versus tabs is just a religious issue,
but for Makefiles it actually matters.
This patch fixes he following errors:
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/powerpc/boot/Makefile:166: *** missing separator. Stop.
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/powerpc/boot/Makefile:171: *** missing separator. Stop.
Since this was inside an ifdef DTC_GENPARSER it was not a problem unless
someone wanted to regenerate the shipped generated files.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The ULI "Super South Bridge" contains ISA bridge to the legacy
devices, such as Super IO mouse/keyboard/floppy disk controllers,
parallel port, i8259 interrupt controller and so on.
i8259 is disabled on the MPC8610HPCD, and other peripherals are not
traced out. So we use only RTC.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The mpc7448hpc2 board doesn't have an alias block like
most of the other modern eval boards have. We need this
block in order to have u-boot be able to make use of the
CONFIG_OF_STDOUT_VIA_ALIAS (vs. having a hard coded node)
in the future.
Also remove the old, redundant chosen node. Of all the modern
Freescale eval boards (incl. 83xx, 85xx, 86xx) this is the only
one which still has it. Its presence also breaks with some older
versions of u-boot, like 1.3.1 -- which try and insert a
second chosen node.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
delete obsolete device-type property, delete model property
(use compatible property instead), prepend "fsl," to Freescale
specific properties. Add nodes to device trees that are missing them,
and fix broken property values in other trees.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Initialize I2C pins on boards with CPM1/CPM2 controllers and document the
i2c bus in booting-without-of.
The boards don't have any I2C chips connected to the I2C bus, so unless
some external chips are connected to the boards, this code is just an
example of setting everything else up.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add support for the MPC8536 process and MPC8536DS reference board. The
MPC8536 is an e500v2 based SoC which eTSEC, USB, SATA, PCI, and PCIe.
The USB and SATA IP blocks are similiar to those on the PQ2 Pro SoCs and
thus use the same drivers.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
It adds the missing RTC node to tqm8548.dts and enables support for
I2C, DS1307 and LM75 in the default configuration.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
i8259 PIC is disabled on MPC8610HPCD, and ULi IDE is configured to use
PCI sideband interrupt that is specified in the device tree.
Current HPCD's device tree specify that IDE interrupt is low to high
sensitive, but in practice ULi IDE throws active-high interrupts (not
active-low as all normal PCI devices).
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Rename MPIC label to mpic to match all other 85xx .dts and to fix compile
issue introduced by addition of the DMA node.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Current device tree is only bare bones. This patch adds nodes to make
it a complete tree for the MPC5121ads.
Added nodes include:
mbx - opengl coprocessor
nfc - nand flash controller
cpld-pic - on board cpld
rtc
clock - clock control
pmc - power management control
gpio
mscan - can module
i2c
axe - audio coprocessor
display - display interface unit
mdio
ethernet
usb
ioctl - pin config
pata
ac97 - PSC configured as AC97
pscfifo - psc fifo configuration
dma
pci
Fix typo in header changing MDS to ADS.
Add a compatible property of the form "fsl,mpc5121-..."
to nodes missing one.
Changed localbus compatible to fsl,mpc5121-localbus, this does
not break anything because the only code that uses it finds it
via the node name, not compatible.
Signed-off-by: John Rigby <jrigby@freescale.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch adds the still missing FDT nodes for the MSCAN devices for
the TQM52xx modules.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
It is inconvenient to add additional default targets to the bootwrapper
Makefile for each new board supported which just needs a different dts
file. This change allows the defconfig to specify additional build
targets.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Various instances of the EMAC core have varying: 1) number of address
match slots, 2) width of the registers for handling address match slots,
3) number of registers for handling address match slots and 4) base
offset for those registers.
As the driver stands today, it assumes that all EMACs have 4 IAHT and
GAHT 32-bit registers, starting at offset 0x30 from the register base,
with only 16-bits of each used for a total of 64 match slots.
The 405EX(r) and 460EX now use the EMAC4SYNC core rather than the EMAC4
core. This core has 8 IAHT and GAHT registers, starting at offset 0x80
from the register base, with ALL 32-bits of each used for a total of
256 match slots.
This adds a new compatible device tree entry "emac4sync" and a new,
related feature flag "EMAC_FTR_EMAC4SYNC" along with a series of macros
and inlines which supply the appropriate parameterized value based on
the presence or absence of the EMAC4SYNC feature.
The code has further been reworked where appropriate to use those macros
and inlines.
In addition, the register size passed to ioremap is now taken from the
device tree:
c4 for EMAC4SYNC cores
74 for EMAC4 cores
70 for EMAC cores
rather than sizeof (emac_regs).
Finally, the device trees have been updated with the appropriate compatible
entries and resource sizes.
This has been tested on an AMCC Haleakala board such that: 1) inbound
ICMP requests to 'haleakala.local' via MDNS from both Mac OS X 10.4.11
and Ubuntu 8.04 systems as well as 2) outbound ICMP requests from
'haleakala.local' to those same systems in the '.local' domain via MDNS
now work.
Signed-off-by: Grant Erickson <gerickson@nuovations.com>
Acked-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The wrapper script is missing the bits needed for building generic
simpleImage targets (targets which don't depend on any particular
firmware interface and retrieve all their data from the device tree).
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The following changes add processing to initialize the Xilinx 16550 UART
in the boot wrapper for Virtex targets without firmware. Normally the
boot wrapper assumes that the serial port has already been initialized by
firmware.
The wrapper was also modified to add the 440 build.
Signed-off-by: John Linn <john.linn@xilinx.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This new file adds support for the ML507 reference design. The ML507
uses the Virtex 5 FXT FPGA which embeds a ppc440 core.
Signed-off-by: John Linn <john.linn@xilinx.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This change to the makefile corrects the build of a simpleImage with initrd.
Signed-off-by: John Linn <john.linn@xilinx>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Since most bootloaders or wrappers tend to update or add some information
to the .dtb they a handled they need some working space to do that in.
By default add 1K of padding via a default setting of DTS_FLAGS.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently we set the start of the .text section to be 4Mb for pSeries.
In situations where the zImage is > 8Mb we'll fail to boot (due to
overlapping with OF). Move .text in a zImage from 4MB to 64MB
(well past OF).
We still will not be able to load large zImage unless we also move OF,
to that end, add a note to the zImage ELF to move OF to 32Mb. If this
is the very first kernel booted then we'll need to move OF manually by
setting real-base.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Added DMA nodes for the elo/elo-plus DMA engines.
Renamed the interrupt controller alias in mpc832x_rdb.dts to ipic so that
its the same as all the other boards.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
GCC 4.4.x looks to be adding support for generating out-of-line register
saves/restores based on:
http://gcc.gnu.org/ml/gcc-patches/2008-04/msg01678.html
This breaks the bootwrapper as we'd need to link with libgcc to get the
implementation of the register save/restores.
To workaround this issue, we just stole the save/restore code from gcc
and simplified it down for our needs (integer only).
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This makes the sam440ep.dts dts-v1 compliant.
Signed-off-by: Giuseppe Coviello <gicoviello@gmail.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
The Sam440ep is an high customizable general purpose mini-itx board,
based on the AMCC 440EP and with a LatticeXP FPGA onboard.
It's poduced by ACube Systems Srl (Bassano del Grappa, Italy),
http://www.acube-systems.biz.
Signed-off-by: Giuseppe Coviello <gicoviello@gmail.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Add support for the NOR flash found on the AMCC Taishan Board
and enable MTD support in the defconfig.
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This is patch adds board file, device tree, and defconfig for the new
board, made by Freescale Semiconductor Inc. and Logic Product Development.
Currently supported:
1. UEC{1,2,7,4};
2. I2C;
3. SPI;
4. NS16550 serial;
5. PCI and miniPCI;
6. Intel NOR StrataFlash X16 64Mbit PC28F640P30T85;
7. Graphics controller, Fujitsu MB86277.
Not supported in this patch:
1. StMICRO NAND512W3A2BN6E, 512 Mbit (supported with FSL UPM NAND driver);
2. FHCI USB (supported with FHCI driver).
3. QE Serial UCCs (tested to not work with ucc_uart driver, reason
unknown, yet);
4. ADC AD7843 (tested to work, but support via device tree depends on
major SPI rework, GPIO API, etc);
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds local bus nodes for Flash and CAN to the DTS file
of the TQM8560 module (tqm8560.dts).
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Some TQM85xx boards could be equipped with up to 1 GiB (NOR) flash
memory and therefore a modified memory map is required and setup by
the board loader. This patch adds an appropriate DTS file.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds support for the TQM8548 modules from TQ-Components
GmbH (http://www.tqc.de).
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Like for the TQM5200, the vendor prefix "tqc," is now used for all
TQM85xx modules from TQ-Components GmbH (http://www.tqc.de) in the
corresponding DTS files.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
MDIO-less PHYs should use CONFIG_FIXED_PHY driver and appropriate
fixed-link property in the device tree.
If not, ethernet will not work:
e0024520:03 not found
eth1: Could not attach to PHY
IP-Config: Failed to open eth1
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Andrew Klossner pointed out the IO space size was in violation of
the alignment requirements for windows on the 85xx. The size should
have been 1M (to match u-boot).
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Support for the C2K cPCI Single Board Computer from GEFanuc
(PowerPC MPC7448 with a Marvell MV64460 chipset).
All features of the board are not supported yet, but the board
boots, flash works, all Ethernet ports are working and PCI
devices are all found (USB and SATA on PCI1 do not work yet).
Part 2 of 5: support for the board in arch/powerpc/boot.
Signed-off-by: Remi Machet <rmachet@slac.stanford.edu>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Support for the C2K cPCI Single Board Computer from GEFanuc
(PowerPC MPC7448 with a Marvell MV64460 chipset).
All features of the board are not supported yet, but the board
boots, flash works, all Ethernet ports are working and PCI
devices are all found (USB and SATA on PCI1 do not work yet).
Part 1 of 5: DTS file describing the board peripherals. As far as I
know all peripherals except the FPGA are listed in there (I did not
include the FPGA because a lot of work is needed there).
Signed-off-by: Remi Machet <rmachet@slac.stanford.edu>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This corrects the names of two CONFIG_ variables.
Note that the CONFIG_MPC86XADS fix uncovers another bug
(with mpc866_ads_defconfig) that will require fixing:
<-- snip -->
...
arch/powerpc/boot/dtc -O dtb -o arch/powerpc/boot/mpc866ads.dtb -b 0 /home/bunk/linux/kernel-2.6/git/linux-2.6/arch/powerpc/boot/dts/mpc866ads.dts
DTC: dts->dtb on file "/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/powerpc/boot/dts/mpc866ads.dts"
WRAP arch/powerpc/boot/cuImage.mpc866ads
powerpc64-linux-ld: arch/powerpc/boot/cuboot-mpc866ads.o: No such file: No such file or directory
make[2]: *** [arch/powerpc/boot/cuImage.mpc866ads] Error 1
<-- snip -->
Reported-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Added next-level-cache to the L1 and a reference to the new L2 label.
This is per the ePAPR 0.94 spec. Since we are't really dependent on this
today we aren't supporting the "legacy" l2-cache phandle that is specified
in the PPC v2.1 OF Binding spec.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Removed clock-frequency, big-endian, and built-in props as they aren't
specified anywhere. Also added compatible = "chrp,open-pic" in the
places it was missing.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The following adds support for the Analogue & Micro ASP 8347E, running
Redboot.
http://www.analogue-micro.com/ASP8347.html
Signed-off-by: Bryan O'Donoghue <bodonoghue@codehermit.ie>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
