Remove filters from being setup in case of software DCB and allow the
LLDP frames to be properly transmitted to the wire.
It is not possible to transmit the LLDP frame out of the port, if they
are filtered by control VSI. This prohibits software LLDP agent
properly communicate its DCB capabilities to the neighbors.
Fixes: 4b208eaa80 ("i40e: Add init and default config of software based DCB")
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Imam Hassan Reza Biswas <imam.hassan.reza.biswas@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Unlike other supported adapters, 2.5G and 5G use different
PHY type identifiers for reading/writing PHY settings
and for reading link status. This commit introduces
separate PHY identifiers for these two operation types.
Fixes: 2e45d3f467 ("i40e: Add support for X710 B/P & SFP+ cards")
Signed-off-by: Dawid Lukwinski <dawid.lukwinski@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When FEC mode was changed the link didn't know it because
the link was not reset and new parameters were not negotiated.
Set a flag 'I40E_AQ_PHY_ENABLE_ATOMIC_LINK' in 'abilities'
to restart the link and make it run with the new settings.
Fixes: 1d96340196 ("i40e: Add support FEC configuration for Fortville 25G")
Signed-off-by: Jaroslaw Gawin <jaroslawx.gawin@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently the call to i40e_client_del_instance frees the object
pf->cinst, however pf->cinst->lan_info is being accessed after
the free. Fix this by adding the missing return.
Addresses-Coverity: ("Read from pointer after free")
Fixes: 7b0b1a6d0a ("i40e: Disable iWARP VSI PETCP_ENA flag on netdev down events")
Signed-off-by: Yunjian Wang <wangyunjian@huawei.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Commit 12738ac475 ("i40e: Fix sparse errors in i40e_txrx.c") broke
XDP support in the i40e driver. That commit was fixing a sparse error
in the code by introducing a new variable xdp_res instead of
overloading this into the skb pointer. The problem is that the code
later uses the skb pointer in if statements and these where not
extended to also test for the new xdp_res variable. Fix this by adding
the correct tests for xdp_res in these places.
The skb pointer was used to store the result of the XDP program by
overloading the results in the error pointer
ERR_PTR(-result). Therefore, the allocation failure test that used to
only test for !skb now need to be extended to also consider !xdp_res.
i40e_cleanup_headers() had a check that based on the skb value being
an error pointer, i.e. a result from the XDP program != XDP_PASS, and
if so start to process a new packet immediately, instead of populating
skb fields and sending the skb to the stack. This check is not needed
anymore, since we have added an explicit test for xdp_res being set
and if so just do continue to pick the next packet from the NIC.
Fixes: 12738ac475 ("i40e: Fix sparse errors in i40e_txrx.c")
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Tested-by: Jesper Dangaard Brouer <brouer@redhat.com>
Reported-by: Jesper Dangaard Brouer <brouer@redhat.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When the FDIR entry is found, just return the result directly to break
the loop.
Signed-off-by: Haiyue Wang <haiyue.wang@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The maximum number (2) of flex-byte support is derived from ethtool
use-def data size (8 byte).
Change the magic number 2 to macro definition, and add the comment to
track the design thinking, so the code is clear and easily maintained.
Signed-off-by: Haiyue Wang <haiyue.wang@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Both iavf_free_all_tx_resources() and iavf_free_all_rx_resources() have
already been called in the very same function.
Remove the duplicate calls.
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The minimum size of admin send/receive queue is 1 and 2 respectively.
The admin send queue can't be set to 1 because in that case, the
firmware would fail to init.
Signed-off-by: Coiby Xu <coxu@redhat.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Use the minimum of the number of descriptors thus we will allocate the
minimal ring buffers for kdump.
Signed-off-by: Coiby Xu <coxu@redhat.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Set the number of the MSI-X vectors to 1. When MSI-X is enabled,
it's not allowed to use more TC queue pairs than MSI-X vectors
(pf->num_lan_msix) exist. Thus the number of Tx and Rx pairs
(vsi->num_queue_pairs) will be equal to the number of MSI-X vectors,
i.e., 1.
Signed-off-by: Coiby Xu <coxu@redhat.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Refactor repeated link state reporting code into a separate helper
functions: i40e_set_vf_link_state() i40e_vc_link_speed2mbps().
Add support of VIRTCHNL_VF_CAP_ADV_LINK_SPEED;
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Provide the ability to enable SCTP RSS hashing by ethtool.
It gives users option of generating RSS hash based on the SCTP source
and destination ports numbers, IPv4 or IPv6 source and destination
addresses.
Signed-off-by: Haiyue Wang <haiyue.wang@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Provides the ability to enable UDP RSS hashing by ethtool.
It gives users option of generating RSS hash based on the UDP source
and destination ports numbers, IPv4 or IPv6 source and destination
addresses.
Signed-off-by: Haiyue Wang <haiyue.wang@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Provides the ability to enable TCP RSS hashing by ethtool.
It gives users option of generating RSS hash based on the TCP source
and destination ports numbers, IPv4 or IPv6 source and destination
addresses.
Signed-off-by: Haiyue Wang <haiyue.wang@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add the virtchnl message interface to VF, so that VF can request RSS
input set(s) based on PF's capability.
This framework allows ethtool RSS config support on the VF driver.
Signed-off-by: Haiyue Wang <haiyue.wang@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently, RSS hash input is not available to AVF by ethtool, it is set
by the PF directly.
Add the RSS configure support for AVF through new virtchnl message, and
define the capability flag VIRTCHNL_VF_OFFLOAD_ADV_RSS_PF to query this
new RSS offload support.
Signed-off-by: Jia Guo <jia.guo@intel.com>
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Signed-off-by: Haiyue Wang <haiyue.wang@intel.com>
Tested-by: Bo Chen <BoX.C.Chen@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently, the driver gets the VF's VSI by using a long string of
dereferences (i.e. vf->pf->vsi[vf->lan_vsi_idx]). If the method to get
the VF's VSI were to change the driver would have to change it in every
location. Fix this by adding the helper ice_get_vf_vsi().
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Pointer vsi is being re-assigned a value that is never read,
the assignment is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add code to support UDP segmentation offload (USO) for
hardware that supports it.
Suggested-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
As the hardware is capable of supporting UDP segmentation offload, add a
capability bit to virtchnl.h to communicate this and have the driver
advertise its support.
Suggested-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Declare bitmap of allowed commands on VF. Initialize default
opcodes list that should be always supported. Declare array of
supported opcodes for each caps used in virtchnl code.
Change allowed bitmap by setting or clearing corresponding
bit to allowlist (bit set) or denylist (bit clear).
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Attempt to detect malicious VFs and, if suspected, log the information but
keep going to allow the user to take any desired actions.
Potentially malicious VFs are identified by checking if the VFs are
transmitting too many messages via the PF-VF mailbox which could cause an
overflow of this channel resulting in denial of service. This is done by
creating a snapshot or static capture of the mailbox buffer which can be
traversed and in which the messages sent by VFs are tracked.
Co-developed-by: Yashaswini Raghuram Prathivadi Bhayankaram <yashaswini.raghuram.prathivadi.bhayankaram@intel.com>
Signed-off-by: Yashaswini Raghuram Prathivadi Bhayankaram <yashaswini.raghuram.prathivadi.bhayankaram@intel.com>
Co-developed-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Co-developed-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Vignesh Sridhar <vignesh.sridhar@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
- keep the ZC code, drop the code related to reinit
net/bridge/netfilter/ebtables.c
- fix build after move to net_generic
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Expose EEE Tx and Rx low power idle counters via ethtool
A EEE TX or RX LPI event occurs when the transmitter or the receiver
enters EEE (IEEE802.3az) LPI state.
ethtool --statistics <iface>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The i225 device offers a number of special PTP Hardware Clock features on
the Software Defined Pins (SDPs) - much like i210, which is used as
inspiration for this patch. It enables two possible functions, namely
time stamping external events and periodic output signals.
The assignment of PHC functions to the four SDP can be freely chosen by
the user.
For the external events time stamping, when the SDP (configured as input
by user) level changes, an interrupt is generated and the kernel
Precision Time Protocol (PTP) is informed.
For the periodic output signals, the i225 is configured to generate them
(so the SDP level will change periodically) and the driver also has to
keep updating the time of the next level change. However, this work is
not necessary for some frequencies as the i225 takes care of them
(namely, anything with a half-cycle of 500ms, 250ms, 125ms or < 70ms).
While i225 allows up to four timers to be used to source the time used
on the external events or output signals, this patch uses only one of
those timers. Main reason is to keep it simple, as it's not clear how
these extra timers would be exposed to users. Note that currently a NIC
can expose a single PTP device.
Signed-off-by: Ederson de Souza <ederson.desouza@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The i225 device can produce one interrupt on the full second, much
like i210 - from where this patch is inspired.
This patch sets up the full second interruption on the i225 and when
receiving it, it sends a PPS event to PTP (Precision Time Protocol)
kernel subsystem.
The PTP subsystem exposes the PPS events via ioctl and sysfs, and one
can use the `testptp` tool (tools/testing/selftests/ptp) to check that
the events are being generated.
Signed-off-by: Ederson de Souza <ederson.desouza@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add new function which checks MTA_REGISTER if its filled correctly.
If not then writes again to same register.
There is possibility that i210 and i211 could not accept
MTA_REGISTER settings, specially when you add and remove
many of multicast addresses in short time.
Without this patch there is possibility that multicast settings will be
not always set correctly in hardware.
Signed-off-by: Grzegorz Siwik <grzegorz.siwik@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
i210 has a total of 24KB of transmit packet buffer. When in Qav mode,
this buffer is divided into four pieces, one for each Tx queue.
Currently, 8KB are given to each of the two SR queues and 4KB are given
to each of the two SP queues.
However, it was noticed that such distribution can make best effort
traffic (which would usually go to the SP queues when Qav is enabled, as
the SR queues would be used by ETF or CBS qdiscs for TSN-aware traffic)
perform poorly. Using iperf3 to measure, one could see the performance
of best effort traffic drop by nearly a third (from 935Mbps to 578Mbps),
with no TSN traffic competing.
This patch redistributes the 24KB to each queue equally: 6KB each. On
tests, there was no notable performance reduction of best effort traffic
performance when there was no TSN traffic competing.
Below, more details about the data collected:
All experiments were run using the following qdisc setup:
qdisc taprio 100: root refcnt 9 tc 4 map 3 3 3 2 3 0 0 3 3 3 3 3 3 3 3 3
queues offset 0 count 1 offset 1 count 1 offset 2 count 1 offset 3 count 1
clockid TAI base-time 0 cycle-time 10000000 cycle-time-extension 0
index 0 cmd S gatemask 0xf interval 10000000
qdisc etf 8045: parent 100:1 clockid TAI delta 1000000 offload on
deadline_mode off skip_sock_check off
TSN traffic, when enabled, had this characteristics:
Packet size: 1500 bytes
Transmission interval: 125us
----------------------------------
Without this patch:
----------------------------------
- TCP data:
- No TSN traffic:
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-20.00 sec 1.35 GBytes 578 Mbits/sec 0
- With TSN traffic:
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-20.00 sec 1.07 GBytes 460 Mbits/sec 1
- TCP data limiting iperf3 buffer size to 4K:
- No TSN traffic:
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-20.00 sec 1.35 GBytes 579 Mbits/sec 0
- With TSN traffic:
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-20.00 sec 1.08 GBytes 462 Mbits/sec 0
- TCP data limiting iperf3 buffer size to 192 bytes (smallest size without
serious performance degradation):
- No TSN traffic:
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-20.00 sec 1.34 GBytes 577 Mbits/sec 0
- With TSN traffic:
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-20.00 sec 1.07 GBytes 461 Mbits/sec 1
- UDP data at 1000Mbit/sec:
- No TSN traffic:
[ ID] Interval Transfer Bitrate Jitter Lost/Total Datagrams
[ 5] 0.00-20.00 sec 1.36 GBytes 586 Mbits/sec 0.000 ms 0/1011407 (0%)
- With TSN traffic:
[ ID] Interval Transfer Bitrate Jitter Lost/Total Datagrams
[ 5] 0.00-20.00 sec 1.05 GBytes 451 Mbits/sec 0.000 ms 0/778672 (0%)
----------------------------------
With this patch:
----------------------------------
- TCP data:
- No TSN traffic:
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-20.00 sec 2.17 GBytes 932 Mbits/sec 0
- With TSN traffic:
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-20.00 sec 1.50 GBytes 646 Mbits/sec 1
- TCP data limiting iperf3 buffer size to 4K:
- No TSN traffic:
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-20.00 sec 2.17 GBytes 931 Mbits/sec 0
- With TSN traffic:
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-20.00 sec 1.50 GBytes 645 Mbits/sec 0
- TCP data limiting iperf3 buffer size to 192 bytes (smallest size without
serious performance degradation):
- No TSN traffic:
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-20.00 sec 2.17 GBytes 932 Mbits/sec 1
- With TSN traffic:
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-20.00 sec 1.50 GBytes 645 Mbits/sec 0
- UDP data at 1000Mbit/sec:
- No TSN traffic:
[ ID] Interval Transfer Bitrate Jitter Lost/Total Datagrams
[ 5] 0.00-20.00 sec 2.23 GBytes 956 Mbits/sec 0.000 ms 0/1650226 (0%)
- With TSN traffic:
[ ID] Interval Transfer Bitrate Jitter Lost/Total Datagrams
[ 5] 0.00-20.00 sec 1.51 GBytes 649 Mbits/sec 0.000 ms 0/1120264 (0%)
Signed-off-by: Ederson de Souza <ederson.desouza@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Fix this panic by adding more rules to calculate the value of @rss_size_max
which could be used in allocating the queues when bpf is loaded, which,
however, could cause the failure and then trigger the NULL pointer of
vsi->rx_rings. Prio to this fix, the machine doesn't care about how many
cpus are online and then allocates 256 queues on the machine with 32 cpus
online actually.
Once the load of bpf begins, the log will go like this "failed to get
tracking for 256 queues for VSI 0 err -12" and this "setup of MAIN VSI
failed".
Thus, I attach the key information of the crash-log here.
BUG: unable to handle kernel NULL pointer dereference at
0000000000000000
RIP: 0010:i40e_xdp+0xdd/0x1b0 [i40e]
Call Trace:
[2160294.717292] ? i40e_reconfig_rss_queues+0x170/0x170 [i40e]
[2160294.717666] dev_xdp_install+0x4f/0x70
[2160294.718036] dev_change_xdp_fd+0x11f/0x230
[2160294.718380] ? dev_disable_lro+0xe0/0xe0
[2160294.718705] do_setlink+0xac7/0xe70
[2160294.719035] ? __nla_parse+0xed/0x120
[2160294.719365] rtnl_newlink+0x73b/0x860
Fixes: 41c445ff0f ("i40e: main driver core")
Co-developed-by: Shujin Li <lishujin@kuaishou.com>
Signed-off-by: Shujin Li <lishujin@kuaishou.com>
Signed-off-by: Jason Xing <xingwanli@kuaishou.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The scope of this variable can be reduced so do that.
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
We were saving the return value from ice_vsi_manage_rss_lut(), but
the errors from that function are not critical so change it to
return void and remove the code that saved the value.
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Silence false errors, warnings and style issues reported by cppcheck.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently the vsi->vf_id is set only for ICE_VSI_VF and it's left as 0
for all other VSI types. This is confusing and could be problematic
since 0 is a valid vf_id. Fix this by always setting non VF VSI types to
ICE_INVAL_VFID.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The only time you can ever have a rq_last_status is if
a firmware event was somehow reporting a status on the receive
queue, which are generally firmware initiated events or
mailbox messages from a VF. Mostly this struct member was unused.
Fix this problem by still printing the value of the field in a debug
print, but don't store the value forever in a struct, potentially
creating opportunities for callers to use the wrong struct member.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Do a minor refactor on ice_vsi_rebuild to use a local
variable to store vsi->type.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The driver previously printed it's PCI address in
the name field for the pci resource, which when displayed
via /proc/iomem, would print the same thing twice.
It's more useful for debugging to see the driver name, as
most other modules do.
Here's a diff of before and after this change:
99100000-991fffff : 0000:3b:00.1
9a000000-a04fffff : PCI Bus 0000:3b
9a000000-9bffffff : 0000:3b:00.1
- 9a000000-9bffffff : 0000:3b:00.1
+ 9a000000-9bffffff : ice
9c000000-9dffffff : 0000:3b:00.0
- 9c000000-9dffffff : 0000:3b:00.0
+ 9c000000-9dffffff : ice
9e000000-9effffff : 0000:3b:00.1
9f000000-9fffffff : 0000:3b:00.0
a0000000-a000ffff : 0000:3b:00.1
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
There was an excessive increment of the QSFP page, which is
now fixed. Additionally, this new update now reads 8 bytes
at a time and will retry each request if the module/bus is
busy.
Also, prevent reading from upper pages if module does not
support those pages.
Signed-off-by: Scott W Taylor <scott.w.taylor@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Use a dedicated bitfield in order to both increase
the amount of checking around the length of ITR writes
as well as simplify the checks of dynamic mode.
Basically unpack the "high bit means dynamic" logic
into bitfields.
Also, remove some unused ITR defines.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The driver would occasionally miss that there were outstanding
descriptors to clean when exiting busy/napi poll. This issue has
been in the code since the introduction of the ice driver.
Attempt to "catch" any remaining work by triggering a software
interrupt when exiting napi poll or busy-poll. This will not
cause extra interrupts in the case of normal execution.
This issue was found when running sfnt-pingpong, with busy
poll enabled, and typically with larger I/O sizes like > 8192,
the program would occasionally report > 1 second maximums
to complete a ping pong.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The ice driver has support for adaptive interrupt moderation, an
algorithm for tuning the interrupt rate dynamically. This algorithm
is based on various assumptions about ring size, socket buffer size,
link speed, SKB overhead, ethernet frame overhead and more.
The Linux kernel has support for a dynamic interrupt moderation
algorithm known as "dimlib". Replace the custom driver-specific
implementation of dynamic interrupt moderation with the kernel's
algorithm.
The Intel hardware has a different hardware implementation than the
originators of the dimlib code had to work with, which requires the
driver to use a slightly different set of inputs for the actual
moderation values, while getting all the advice from dimlib of
better/worse, shift left or right.
The change made for this implementation is to use a pair of values
for each of the 5 "slots" that the dimlib moderation expects, and
the driver will program those pairs when dimlib recommends a slot to
use. The currently implementation uses two tables, one for receive
and one for transmit, and the pairs of values in each slot set the
maximum delay of an interrupt and a maximum number of interrupts per
second (both expressed in microseconds).
There are two separate kinds of bugs fixed by using DIMLIB, one is
UDP single stream send was too slow, and the other is that 8K
ping-pong was going to the most aggressive moderation and has much
too high latency.
The overall result of using DIMLIB is that we meet or exceed our
performance expectations set based on the old algorithm.
Co-developed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Introduce several new helpers for writing ITR and GLINT_RATE
registers, and refactor the code calling them. This resulted
in removal of several duplicate functions and rolled a bunch
of simple code back into the calling routines.
In particular this removes some code that was doing both
a store and a set in a helper function, which seems better
done as separate tasks in the caller (and generally takes
less lines of code even with a tiny bit of repetition).
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add two new VSI states, one to track if a netdev for the VSI has been
allocated and the other to track if the netdev has been registered.
Call unregister_netdev/free_netdev only when the corresponding state
bits are set.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Remove the leading underscores in enum ice_pf_state. This is not really
communicating anything and is unnecessary. No functional change.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The well-known IANA protocol port 3260 (iscsi-target 0x0cbc) and the
ether-types 0x8906 (ETH_P_FCOE) and 0x8914 (ETH_P_FIP) are already defined
in kernel header files. Use those definitions instead of open-coding the
same.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Remove the 'ixgbe_mc_addr_itr' typedef as it is not used.
Signed-off-by: Chen Lin <chen.lin5@zte.com.cn>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
