cmn_refclk_<p/m> lines in Torrent SERDES is used for connecting external
reference clock. cmn_refclk_<p/m> can also be configured to output the
reference clock. In order to drive the refclk out from the SERDES
(Cadence Torrent), PHY_EN_REFCLK should be set in SERDES_RST of WIZ.
Model PHY_EN_REFCLK as a clock, so that platforms like AM642 EVM can
enable it.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Link: https://lore.kernel.org/r/20210310120840.16447-6-kishon@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
commit 091876cc35 ("phy: ti: j721e-wiz: Add support for WIZ module
present in TI J721E SoC") modeled the internal clocks depending on the
subnodes that are populated in device tree. However recent discussions
in the mailing list [1] suggested to just add #clock cells in the parent
DT node and model the clocks within the driver.
Model the mux clocks without device tree input for AM64x SoC. Don't
remove the earlier design since DT nodes for J7200 and J721e are already
upstreamed.
[1] -> http://lore.kernel.org/r/20210108025943.GA1790601@robh.at.kernel.org
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Link: https://lore.kernel.org/r/20210310120840.16447-5-kishon@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The frequency of the txmclk between PCIe and SERDES has
changed to 250MHz from 500MHz. Configure full rate divider
for AM64 accordingly.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Link: https://lore.kernel.org/r/20210310120840.16447-4-kishon@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
commit 091876cc35 ("phy: ti: j721e-wiz: Add support for WIZ module
present in TI J721E SoC") modeled both MUX clocks and DIVIDER clocks in
wiz. However during cleanup, it removed only the MUX clock provider.
Remove the DIVIDER clock provider here.
Fixes: 091876cc35 ("phy: ti: j721e-wiz: Add support for WIZ module present in TI J721E SoC")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Link: https://lore.kernel.org/r/20210310120840.16447-3-kishon@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Both "struct wiz_clk_div_sel" and "struct wiz_clk_mux_sel" are static
data that is common for all wiz instances. Including
"struct regmap_field" for each of the wiz instances can yield undesirable
results. Move "struct regmap_field" out of "struct wiz_clk_div_sel" and
"struct wiz_clk_mux_sel" and make them point to constant data.
So far no issues are observed since both these structures are not
accessed outside the probe.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Link: https://lore.kernel.org/r/20210310120840.16447-2-kishon@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Fix OF node leaks by calling of_node_put in
for_each_child_of_node when the cycle returns.
Generated by: scripts/coccinelle/iterators/for_each_child.cocci
Signed-off-by: Junlin Yang <yangjunlin@yulong.com>
Link: https://lore.kernel.org/r/20210216082739.1414-1-angkery@163.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Start by reading the content of the VENDOR_SPECIFIC2 register and update
each bit field based on device properties when defined.
The use of bit masks prevents fields from overriding each other and
enables users to clear bits which are set by default, like datapolarity
in this instance.
Signed-off-by: Liam Beguin <lvb@xiphos.com>
Link: https://lore.kernel.org/r/20201211191241.21306-1-liambeguin@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
If devm_phy_create() fails then we need to call of_clk_del_provider(node)
to undo the call to of_clk_add_provider().
Fixes: 71e2f5c5c2 ("phy: ti: Add a new SERDES driver for TI's AM654x SoC")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20200905124648.GA183976@mwanda
Signed-off-by: Vinod Koul <vkoul@kernel.org>
On K3 AM654x/J721E platforms the Port MII mode selection register(s) have
similar format and placed in the System Control Module (SCM) module
sequentially as one register per port, but, depending SOC and CPSW
instance, the base offset and number of ports can be different.
Hence, add possibility to retrieve number of ports and base registers
offset from DT and support for max possible number of ports supported by K3
SoCs like J721E.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Link: https://lore.kernel.org/r/20200828201943.29155-4-grygorii.strashko@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
AM654x PG1.0 has a silicon bug that D+ is pulled high after POR, which
could cause enumeration failure with some USB hubs. Disabling the
USB2_PHY Charger Detect function will put D+ into the normal state.
This addresses Silicon Errata:
i2075 - "USB2PHY: USB2PHY Charger Detect is Enabled by Default Without VBUS
Presence"
Signed-off-by: Roger Quadros <rogerq@ti.com>
Tested-by: Jan Kiszka <jan.kiszka@siemens.com>
Link: https://lore.kernel.org/r/20200824075127.14902-2-rogerq@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Update PCIe serdes config to latest suggested for
hardware. This fixes cases of failure to enumerate
in Gen2 mode with some cards.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Link: https://lore.kernel.org/r/20200727194603.44636-4-nsekhar@ti.com
[fix typo threshold]
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Checking return value after each regfield write becomes
hard to read quickly as number of writes increase.
Simplify by checking for error only once.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Link: https://lore.kernel.org/r/20200727194603.44636-3-nsekhar@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
regfield handling in current driver code is made complicated
by having a separate regfield variable for each field which
is allocated individually.
This quickly gets unwieldy once number of regfields increase.
Instead, use an array of regfields which are allocated in a
loop.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Link: https://lore.kernel.org/r/20200727194603.44636-2-nsekhar@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
ti_pipe3_power_on() sets variable 'ret' but never uses it, so remove it.
drivers/phy/ti/phy-ti-pipe3.c:340:6: warning: variable ‘ret’ set but not
used [-Wunused-but-set-variable]
Link: https://lore.kernel.org/r/20200629145010.122675-4-vkoul@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
dm816x_usb_phy_init() sets variable 'error' but never uses it, so remove
it.
drivers/phy/ti/phy-dm816x-usb.c:85:6: warning: variable ‘error’ set but
not used [-Wunused-but-set-variable]
Link: https://lore.kernel.org/r/20200629145010.122675-3-vkoul@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
clk_div_table and wiz_regmap_config are not modified and can therefore
be made const to allow the compiler to put them in read-only memory.
Before:
text data bss dec hex filename
20265 7044 64 27373 6aed drivers/phy/ti/phy-j721e-wiz.o
After:
text data bss dec hex filename
20649 6660 64 27373 6aed drivers/phy/ti/phy-j721e-wiz.o
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Link: https://lore.kernel.org/r/20200524095516.25227-3-rikard.falkeborn@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
regmap_config is not modified and can be made static to allow the compiler
to put it in read-only memory.
Before:
text data bss dec hex filename
12328 3644 64 16036 3ea4 drivers/phy/ti/phy-am654-serdes.o
After:
text data bss dec hex filename
12648 3324 64 16036 3ea4 drivers/phy/ti/phy-am654-serdes.o
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Link: https://lore.kernel.org/r/20200524095516.25227-2-rikard.falkeborn@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The max_register property must be set in order to
show up the registers in debugfs.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Link: https://lore.kernel.org/r/20200513131254.10497-2-rogerq@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Move private definitions from header to phy-omap-usb2.c file.
Get rid of unused data structures usb_dpll_params and omap_usb_phy_type.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Link: https://lore.kernel.org/r/20200515080518.26870-2-rogerq@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Fix to return negative error code from some error handling
cases instead of 0, as done elsewhere in this function.
Fixes: 091876cc35 ("phy: ti: j721e-wiz: Add support for WIZ module present in TI J721E SoC")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Link: https://lore.kernel.org/r/20200507054109.110849-1-weiyongjun1@huawei.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
For DisplayPort use we need to set WIZ_CONFIG_LANECTL register's
P_STANDARD_MODE bits to "mode 3". In the DisplayPort use also the
P_ENABLE bits of the same register are set to P_ENABLE instead of
P_ENABLE_FORCE, so that the DisplayPort driver can enable and disable
the lane as needed. The DisplayPort mode is selected according to
"cdns,phy-type"-properties found in link subnodes under the managed
serdes (see "ti,sierra-phy-t0" and "ti,j721e-serdes-10g" devicetree
bindings for details). All other values of "cdns,phy-type"-property
but PHY_TYPE_DP will set P_STANDARD_MODE bits to 0 and P_ENABLE bits
to force enable.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Pull networking updates from David Miller:
"Highlights:
1) Fix the iwlwifi regression, from Johannes Berg.
2) Support BSS coloring and 802.11 encapsulation offloading in
hardware, from John Crispin.
3) Fix some potential Spectre issues in qtnfmac, from Sergey
Matyukevich.
4) Add TTL decrement action to openvswitch, from Matteo Croce.
5) Allow paralleization through flow_action setup by not taking the
RTNL mutex, from Vlad Buslov.
6) A lot of zero-length array to flexible-array conversions, from
Gustavo A. R. Silva.
7) Align XDP statistics names across several drivers for consistency,
from Lorenzo Bianconi.
8) Add various pieces of infrastructure for offloading conntrack, and
make use of it in mlx5 driver, from Paul Blakey.
9) Allow using listening sockets in BPF sockmap, from Jakub Sitnicki.
10) Lots of parallelization improvements during configuration changes
in mlxsw driver, from Ido Schimmel.
11) Add support to devlink for generic packet traps, which report
packets dropped during ACL processing. And use them in mlxsw
driver. From Jiri Pirko.
12) Support bcmgenet on ACPI, from Jeremy Linton.
13) Make BPF compatible with RT, from Thomas Gleixnet, Alexei
Starovoitov, and your's truly.
14) Support XDP meta-data in virtio_net, from Yuya Kusakabe.
15) Fix sysfs permissions when network devices change namespaces, from
Christian Brauner.
16) Add a flags element to ethtool_ops so that drivers can more simply
indicate which coalescing parameters they actually support, and
therefore the generic layer can validate the user's ethtool
request. Use this in all drivers, from Jakub Kicinski.
17) Offload FIFO qdisc in mlxsw, from Petr Machata.
18) Support UDP sockets in sockmap, from Lorenz Bauer.
19) Fix stretch ACK bugs in several TCP congestion control modules,
from Pengcheng Yang.
20) Support virtual functiosn in octeontx2 driver, from Tomasz
Duszynski.
21) Add region operations for devlink and use it in ice driver to dump
NVM contents, from Jacob Keller.
22) Add support for hw offload of MACSEC, from Antoine Tenart.
23) Add support for BPF programs that can be attached to LSM hooks,
from KP Singh.
24) Support for multiple paths, path managers, and counters in MPTCP.
From Peter Krystad, Paolo Abeni, Florian Westphal, Davide Caratti,
and others.
25) More progress on adding the netlink interface to ethtool, from
Michal Kubecek"
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2121 commits)
net: ipv6: rpl_iptunnel: Fix potential memory leak in rpl_do_srh_inline
cxgb4/chcr: nic-tls stats in ethtool
net: dsa: fix oops while probing Marvell DSA switches
net/bpfilter: remove superfluous testing message
net: macb: Fix handling of fixed-link node
net: dsa: ksz: Select KSZ protocol tag
netdevsim: dev: Fix memory leak in nsim_dev_take_snapshot_write
net: stmmac: add EHL 2.5Gbps PCI info and PCI ID
net: stmmac: add EHL PSE0 & PSE1 1Gbps PCI info and PCI ID
net: stmmac: create dwmac-intel.c to contain all Intel platform
net: dsa: bcm_sf2: Support specifying VLAN tag egress rule
net: dsa: bcm_sf2: Add support for matching VLAN TCI
net: dsa: bcm_sf2: Move writing of CFP_DATA(5) into slicing functions
net: dsa: bcm_sf2: Check earlier for FLOW_EXT and FLOW_MAC_EXT
net: dsa: bcm_sf2: Disable learning for ASP port
net: dsa: b53: Deny enslaving port 7 for 7278 into a bridge
net: dsa: b53: Prevent tagged VLAN on port 7 for 7278
net: dsa: b53: Restore VLAN entries upon (re)configuration
net: dsa: bcm_sf2: Fix overflow checks
hv_netvsc: Remove unnecessary round_up for recv_completion_cnt
...
The phy-gmii-sel can be only auto selected in Kconfig and now the pretty
complex Kconfig dependencies are defined for phy-gmii-sel driver, which
also need to be updated every time phy-gmii-sel is re-used for any new
networking driver.
Simplify Kconfig definition for phy-gmii-sel PHY driver - drop all
dependencies and from networking drivers and rely on using 'imply
PHY_TI_GMII_SEL' in Kconfig definitions for networking drivers instead.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Tested-by: Murali Karicheri <m-karicheri2@ti.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
*) Rename and Re-design phy-cadence-dp driver to phy-cadence-torrent driver
*) Add new PHY driver for Qualcomm 28nm Hi-Speed USB PHY
*) Add new PHY driver for Qualcomm Super Speed PHY in QCS404
*) Add support for Qualcomm PCIe QMP/QHP PHY in SDM845 to phy-qcom-qmp driver
*) Add support for Qualcomm UFS PHY in MSM8996 to phy-qcom-qmp driver
*) Add support for an additional reference clock in Mediatek phy-mtk-tphy driver
*) Add support for configuring tuning parameters in Mediatek phy-mtk-tphy driver
*) Add support for GMII PHY in TI K3 AM654x/J721E SoCs to phy-gmii-sel driver
*) Add support for USB2 PHY in Amlogic A1 SoC Family to phy-meson-g12a-usb2
driver
*) Add support for USB3/USB2/PCIe PHY in Socionext Pro5 SoC to
phy-uniphier-usb3ss/phy-uniphier-usb3hs/phy-uniphier-pcie driver respectively
*) Add support for QUSB2 PHY in Qualcomm SC7180 in driver
*) Convert dt-bindings of Cadence DP, Qualcomm QUSB2 to YAML format
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
-----BEGIN PGP SIGNATURE-----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=+CzV
-----END PGP SIGNATURE-----
Merge tag 'phy-for-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-next
Kishon writes:
phy: for 5.7
*) Rename and Re-design phy-cadence-dp driver to phy-cadence-torrent driver
*) Add new PHY driver for Qualcomm 28nm Hi-Speed USB PHY
*) Add new PHY driver for Qualcomm Super Speed PHY in QCS404
*) Add support for Qualcomm PCIe QMP/QHP PHY in SDM845 to phy-qcom-qmp driver
*) Add support for Qualcomm UFS PHY in MSM8996 to phy-qcom-qmp driver
*) Add support for an additional reference clock in Mediatek phy-mtk-tphy driver
*) Add support for configuring tuning parameters in Mediatek phy-mtk-tphy driver
*) Add support for GMII PHY in TI K3 AM654x/J721E SoCs to phy-gmii-sel driver
*) Add support for USB2 PHY in Amlogic A1 SoC Family to phy-meson-g12a-usb2
driver
*) Add support for USB3/USB2/PCIe PHY in Socionext Pro5 SoC to
phy-uniphier-usb3ss/phy-uniphier-usb3hs/phy-uniphier-pcie driver respectively
*) Add support for QUSB2 PHY in Qualcomm SC7180 in driver
*) Convert dt-bindings of Cadence DP, Qualcomm QUSB2 to YAML format
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
* tag 'phy-for-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy: (52 commits)
phy: qcom-qusb2: Add new overriding tuning parameters in QUSB2 V2 PHY
phy: qcom-qusb2: Add support for overriding tuning parameters in QUSB2 V2 PHY
dt-bindings: phy: qcom-qusb2: Add support for overriding Phy tuning parameters
phy: qcom-qusb2: Add generic QUSB2 V2 PHY support
dt-bindings: phy: qcom,qusb2: Add compatibles for QUSB2 V2 phy and SC7180
dt-bindings: phy: qcom,qusb2: Convert QUSB2 phy bindings to yaml
phy: rk-inno-usb2: Decrease verbosity of repeating log.
phy: amlogic: Add Amlogic A1 USB2 PHY Driver
dt-bindings: phy: Add Amlogic A1 USB2 PHY Bindings
phy: ti: gmii-sel: add support for am654x/j721e soc
dt-bindings: phy: ti: gmii-sel: add support for am654x/j721e soc
phy: qualcomm: usb: Add SuperSpeed PHY driver
dt-bindings: Add Qualcomm USB SuperSpeed PHY bindings
phy: qualcomm: Add Synopsys 28nm Hi-Speed USB PHY driver
dt-bindings: phy: Add Qualcomm Synopsys Hi-Speed USB PHY binding
dt-bindings: phy: remove qcom-dwc3-usb-phy
phy: phy-mtk-tphy: add a new reference clock
phy: phy-mtk-tphy: remove unused u3phya_ref clock
phy: phy-mtk-tphy: make the ref clock optional
phy: phy-mtk-tphy: add a property for internal resistance
...
TI AM654x/J721E SoCs have the same PHY interface selection mechanism for
CPSWx subsystem as TI SoCs (AM3/4/5/DRA7), but registers and bit-fields
placement is different.
This patch adds corresponding support for TI AM654x/J721E SoCs PHY
interface selection.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The "gmii" PHY interface mode is supported on TI AM335x/437x/5xx SoCs, so
don't fail if it's selected.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
- under PHY_INTERFACE_MODE_MII the 'mode' func parameter is assigned
instead of 'gmii_sel_mode' and it's working only because the default value
'gmii_sel_mode' is set to 0.
- console outputs use 'rgmii_id' and 'mode' values to print PHY mode
instead of using 'submode' value which is representing PHY interface mode
now.
This patch fixes above two cases.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
If CONFIG_OF_ADDRESS is not set and COMPILE_TEST=y, the following
error is seen while building phy-j721e-wiz.c
drivers/phy/ti/phy-j721e-wiz.o: In function `wiz_remove':
phy-j721e-wiz.c:(.text+0x1a): undefined reference to
`of_platform_device_destroy'
Fix the config dependency for PHY_J721E_WIZ here.
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 091876cc35 ("phy: ti: j721e-wiz: Add support for WIZ module present in TI J721E SoC")
Signed-off-by: Hongbo Yao <yaohongbo@huawei.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Link: https://lore.kernel.org/r/20200117212310.2864-1-kishon@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case of error, the function devm_ioremap() returns NULL pointer not
ERR_PTR(). The IS_ERR() test in the return value check should be
replaced with NULL test.
Fixes: 091876cc35 ("phy: ti: j721e-wiz: Add support for WIZ module present in TI J721E SoC")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Based on this GPIO state we need to configure LN10
bit to swap lane0 and lane1 if required (flipped connector).
Type-C companions typically need some time after the cable is
plugged before and before they reflect the correct status of
Type-C plug orientation on the DIR line.
Type-C Spec specifies CC attachment debounce time (tCCDebounce)
of 100 ms (min) to 200 ms (max).
Use the DT property to figure out if we need to add delay
or not before sampling the Type-C DIR line.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Reviewed-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Some of the phy drivers can be compile tested to increase build
coverage.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add support for WIZ module present in TI's J721E SoC. WIZ is a SERDES
wrapper used to configure some of the input signals to the SERDES. It is
used with both Sierra(16G) and Torrent(10G) SERDES. This driver configures
three clock selects (pll0, pll1, dig), two divider clocks and supports
resets for each of the lanes.
[jsarha@ti.com: Add support for Torrent(10G) SERDES wrapper]
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The driver calls clk_prepare_enable in probe but the corresponding
clk_disable_unprepare() is in ti_pipe3_disable_clocks().
Move clk_disable_unprepare() to remove to make them symmetric.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Here is the big set of char/misc and other driver patches for 5.5-rc1
Loads of different things in here, this feels like the catch-all of
driver subsystems these days. Full details are in the shortlog, but
nothing major overall, just lots of driver updates and additions.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXd6ewA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymNXACfebVkDrFOH9EqDgFArPvZ1i9EmZ4AoLbE1Wki
ftJApk+Ov1BT2TvClOza
=cXqg
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the big set of char/misc and other driver patches for 5.5-rc1
Loads of different things in here, this feels like the catch-all of
driver subsystems these days. Full details are in the shortlog, but
nothing major overall, just lots of driver updates and additions.
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (198 commits)
char: Fix Kconfig indentation, continued
habanalabs: add more protection of device during reset
habanalabs: flush EQ workers in hard reset
habanalabs: make the reset code more consistent
habanalabs: expose reset counters via existing INFO IOCTL
habanalabs: make code more concise
habanalabs: use defines for F/W files
habanalabs: remove prints on successful device initialization
habanalabs: remove unnecessary checks
habanalabs: invalidate MMU cache only once
habanalabs: skip VA block list update in reset flow
habanalabs: optimize MMU unmap
habanalabs: prevent read/write from/to the device during hard reset
habanalabs: split MMU properties to PCI/DRAM
habanalabs: re-factor MMU masks and documentation
habanalabs: type specific MMU cache invalidation
habanalabs: re-factor memory module code
habanalabs: export uapi defines to user-space
habanalabs: don't print error when queues are full
habanalabs: increase max jobs number to 512
...
Add dependency from TI_CPSW_SWITCHDEV.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now phy-gmii-sel will disable MAC TX internal delay for PHY interface mode
"rgmii-rxid" which is incorrect.
Hence, fix it by enabling MAC TX internal delay in the case of "rgmii-rxid"
mode.
Fixes: 92b58b3474 ("phy: ti: introduce phy-gmii-sel driver")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/phy/ti/phy-dm816x-usb.c:192:29: warning:
variable phy_data set but not used [-Wunused-but-set-variable]
It is never used, so can be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
clk registration by clk providers and debugfs "nice to haves" for rate
constraints. I'll highlight that we're now setting the clk_init_data pointer
inside struct clk_hw to NULL during clk_register(), which may break some
drivers that thought they could use that pointer during normal operations. That
change has been sitting in next for a while now but maybe something is still
broken. We'l see. Other than that the core framework changes aren't invasive
and they're fixing bugs, simplifying, and making things better.
On the clk driver side we got the usual addition of new SoC support, new
features for existing drivers, and bug fixes scattered throughout. The biggest
diffstat is the Amlogic driver that gained CPU clk support in addition to
migrating to the new way of specifying clk parents. After that the Qualcomm,
i.MX, Mediatek, and Rockchip clk drivers got support for various new SoCs and
clock controllers from those vendors.
Core:
- Drop NULL checks in clk debugfs
- Add min/max rates to clk debugfs
- Set clk_init_data pointer inside clk_hw to NULL after registration
- Make clk_bulk_get_all() return an 'id' corresponding to clock-names
- Evict parents from parent cache when they're unregistered
New Drivers:
- Add clock driver for i.MX8MN SoCs
- Support aspeed AST2600 SoCs
- Support for Mediatek MT6779 SoCs
- Support qcom SM8150 GCC and RPMh clks
- Support qcom QCS404 WCSS clks
- Add CPU clock support for Armada 7K/8K (specifically AP806 and AP807)
- Addition of clock driver for Rockchip rk3308 SoCs
Updates:
- Add regulator support to the cdce925 clk driver
- Add support for Raspberry Pi 4 bcm2711 SoCs
- Add SDIO gate support to aspeed driver
- Add missing of_node_put() calls in various clk drivers
- Migrate Amlogic driver to new clock parent description method
- Add DVFS support to Amlogic Meson g12
- Add Amlogic Meson g12a reset support to the axg audio clock controller
- Add sm1 support to the Amlogic Meson g12a clock controller
- Switch i.MX8MM clock driver to platform driver
- Add Hifi4 DSP related clocks for i.MX8QXP SoC
- Fix Audio PLL setting and parent clock for USB
- Misc i.MX8 clock driver improvements and corrections
- Set floor ops for Qualcomm SD clks so that rounding works
- Fix "always-on" Clock Domains on Renesas R-Car M1A, RZ/A1, RZ/A2, and RZ/N1
- Enable the Allwinner V3 SoC and fix the i2s clock for H6
-----BEGIN PGP SIGNATURE-----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=z8wK
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"We have a small collection of core framework updates this time, mostly
around clk registration by clk providers and debugfs "nice to haves"
for rate constraints. I'll highlight that we're now setting the
clk_init_data pointer inside struct clk_hw to NULL during
clk_register(), which may break some drivers that thought they could
use that pointer during normal operations. That change has been
sitting in next for a while now but maybe something is still broken.
We'l see. Other than that the core framework changes aren't invasive
and they're fixing bugs, simplifying, and making things better.
On the clk driver side we got the usual addition of new SoC support,
new features for existing drivers, and bug fixes scattered throughout.
The biggest diffstat is the Amlogic driver that gained CPU clk support
in addition to migrating to the new way of specifying clk parents.
After that the Qualcomm, i.MX, Mediatek, and Rockchip clk drivers got
support for various new SoCs and clock controllers from those vendors.
Core:
- Drop NULL checks in clk debugfs
- Add min/max rates to clk debugfs
- Set clk_init_data pointer inside clk_hw to NULL after registration
- Make clk_bulk_get_all() return an 'id' corresponding to clock-names
- Evict parents from parent cache when they're unregistered
New Drivers:
- Add clock driver for i.MX8MN SoCs
- Support aspeed AST2600 SoCs
- Support for Mediatek MT6779 SoCs
- Support qcom SM8150 GCC and RPMh clks
- Support qcom QCS404 WCSS clks
- Add CPU clock support for Armada 7K/8K (specifically AP806 and AP807)
- Addition of clock driver for Rockchip rk3308 SoCs
Updates:
- Add regulator support to the cdce925 clk driver
- Add support for Raspberry Pi 4 bcm2711 SoCs
- Add SDIO gate support to aspeed driver
- Add missing of_node_put() calls in various clk drivers
- Migrate Amlogic driver to new clock parent description method
- Add DVFS support to Amlogic Meson g12
- Add Amlogic Meson g12a reset support to the axg audio clock controller
- Add sm1 support to the Amlogic Meson g12a clock controller
- Switch i.MX8MM clock driver to platform driver
- Add Hifi4 DSP related clocks for i.MX8QXP SoC
- Fix Audio PLL setting and parent clock for USB
- Misc i.MX8 clock driver improvements and corrections
- Set floor ops for Qualcomm SD clks so that rounding works
- Fix "always-on" Clock Domains on Renesas R-Car M1A, RZ/A1, RZ/A2, and RZ/N1
- Enable the Allwinner V3 SoC and fix the i2s clock for H6"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (137 commits)
clk: Drop !clk checks in debugfs dumping
clk: imx: imx8mn: fix pll mux bit
clk: imx: imx8mm: fix pll mux bit
clk: imx: clk-pll14xx: unbypass PLL by default
clk: imx: pll14xx: avoid glitch when set rate
clk: mvebu: ap80x: add AP807 clock support
clk: mvebu: ap806: Prepare the introduction of AP807 clock support
clk: mvebu: ap806: add AP-DCLK (hclk) to system controller driver
clk: mvebu: ap806: be more explicit on what SaR is
clk: mvebu: ap80x-cpu: add AP807 CPU clock support
clk: mvebu: ap806-cpu: prepare mapping of AP807 CPU clock
dt-bindings: ap806: Document AP807 clock compatible
dt-bindings: ap80x: Document AP807 CPU clock compatible
clk: sprd: add missing kfree
clk: at91: allow 24 Mhz clock as input for PLL
clk: Make clk_bulk_get_all() return a valid "id"
clk: actions: Fix factor clk struct member access
clk: qcom: rcg: Return failure for RCG update
clk: remove extra ---help--- tags in Kconfig
clk: add include guard to clk-conf.h
...
The regmap_node variable is still being used in the syscon_node_to_regmap()
call after the of_node_put() call, which may result in use-after-free.
Fixes: 71e2f5c5c2 ("phy: ti: Add a new SERDES driver for TI's AM654x SoC")
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Roger Quadros <rogerq@ti.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
A future patch is going to change semantics of clk_register() so that
clk_hw::init is guaranteed to be NULL after a clk is registered. Avoid
referencing this member here so that we don't run into NULL pointer
exceptions.
Cc: Roger Quadros <rogerq@ti.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lkml.kernel.org/r/20190731193517.237136-9-sboyd@kernel.org
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
*) Add a new PHY driver for Qualcomm PCIe2 PHY
*) Add a new PHY driver for Mixel DPHY present in i.MX8
*) Fix Qualcomm QMP UFS PHY driver from incorrectly reporting that
PHY enable failed
*) Fix _BUG_ on Amlogic G12A USB3 + PCIE Combo PHY Driver due to
calling a sleeping function from invalid context
*) Fix WARN_ON dump on rcar-gen3-usb2 PHY driver caused due to
imbalance powered flag
*) Fix .cocci and sparse warnings
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
-----BEGIN PGP SIGNATURE-----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=5mPE
-----END PGP SIGNATURE-----
Merge tag 'phy-for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-next
phy: for 5.3
*) Add a new PHY driver for Qualcomm PCIe2 PHY
*) Add a new PHY driver for Mixel DPHY present in i.MX8
*) Fix Qualcomm QMP UFS PHY driver from incorrectly reporting that
PHY enable failed
*) Fix _BUG_ on Amlogic G12A USB3 + PCIE Combo PHY Driver due to
calling a sleeping function from invalid context
*) Fix WARN_ON dump on rcar-gen3-usb2 PHY driver caused due to
imbalance powered flag
*) Fix .cocci and sparse warnings
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
* tag 'phy-for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy:
phy: qcom-qmp: Raise qcom_qmp_phy_enable() polling delay
phy: meson-g12a-usb3-pcie: disable locking for cr_regmap
phy: Add driver for mixel mipi dphy found on NXP's i.MX8 SoCs
dt-bindings: phy: Add documentation for mixel dphy
dt-bindings: phy-pxa-usb: add bindings
phy: renesas: rcar-gen3-usb2: fix imbalance powered flag
phy: qcom-qmp: Drop useless msm8998_pciephy_cfg setting
phy: qcom-qmp: Correct READY_STATUS poll break condition
phy: ti: am654-serdes: Make serdes_am654_xlate() static
phy: usb: phy-brcm-usb: Fix platform_no_drv_owner.cocci warnings
phy: samsung: Use struct_size() in devm_kzalloc()
phy: qcom: Add Qualcomm PCIe2 PHY driver
dt-bindings: phy: Add binding for Qualcomm PCIe2 PHY
