Pull two powerpc fixes from Ben Herrenschmidt:
"Here's a pair of powerpc fixes for 3.15 which are also going to
stable.
One's a fix for building with newer binutils (the problem currently
only affects the BookE kernels but the affected macro might come back
into use on BookS platforms at any time). Unfortunately, the binutils
maintainer did a backward incompatible change to a construct that we
use so we have to add Makefile check.
The other one is a fix for CPUs getting stuck in kexec when running
single threaded. Since we routinely use kexec on power (including in
our newer bootloaders), I deemed that important enough"
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc, kexec: Fix "Processor X is stuck" issue during kexec from ST mode
powerpc: Fix 64 bit builds with binutils 2.24
If we try to perform a kexec when the machine is in ST (Single-Threaded) mode
(ppc64_cpu --smt=off), the kexec operation doesn't succeed properly, and we
get the following messages during boot:
[ 0.089866] POWER8 performance monitor hardware support registered
[ 0.089985] power8-pmu: PMAO restore workaround active.
[ 5.095419] Processor 1 is stuck.
[ 10.097933] Processor 2 is stuck.
[ 15.100480] Processor 3 is stuck.
[ 20.102982] Processor 4 is stuck.
[ 25.105489] Processor 5 is stuck.
[ 30.108005] Processor 6 is stuck.
[ 35.110518] Processor 7 is stuck.
[ 40.113369] Processor 9 is stuck.
[ 45.115879] Processor 10 is stuck.
[ 50.118389] Processor 11 is stuck.
[ 55.120904] Processor 12 is stuck.
[ 60.123425] Processor 13 is stuck.
[ 65.125970] Processor 14 is stuck.
[ 70.128495] Processor 15 is stuck.
[ 75.131316] Processor 17 is stuck.
Note that only the sibling threads are stuck, while the primary threads (0, 8,
16 etc) boot just fine. Looking closer at the previous step of kexec, we observe
that kexec tries to wakeup (bring online) the sibling threads of all the cores,
before performing kexec:
[ 9464.131231] Starting new kernel
[ 9464.148507] kexec: Waking offline cpu 1.
[ 9464.148552] kexec: Waking offline cpu 2.
[ 9464.148600] kexec: Waking offline cpu 3.
[ 9464.148636] kexec: Waking offline cpu 4.
[ 9464.148671] kexec: Waking offline cpu 5.
[ 9464.148708] kexec: Waking offline cpu 6.
[ 9464.148743] kexec: Waking offline cpu 7.
[ 9464.148779] kexec: Waking offline cpu 9.
[ 9464.148815] kexec: Waking offline cpu 10.
[ 9464.148851] kexec: Waking offline cpu 11.
[ 9464.148887] kexec: Waking offline cpu 12.
[ 9464.148922] kexec: Waking offline cpu 13.
[ 9464.148958] kexec: Waking offline cpu 14.
[ 9464.148994] kexec: Waking offline cpu 15.
[ 9464.149030] kexec: Waking offline cpu 17.
Instrumenting this piece of code revealed that the cpu_up() operation actually
fails with -EBUSY. Thus, only the primary threads of all the cores are online
during kexec, and hence this is a sure-shot receipe for disaster, as explained
in commit e8e5c2155b (powerpc/kexec: Fix orphaned offline CPUs across kexec),
as well as in the comment above wake_offline_cpus().
It turns out that cpu_up() was returning -EBUSY because the variable
'cpu_hotplug_disabled' was set to 1; and this disabling of CPU hotplug was done
by migrate_to_reboot_cpu() inside kernel_kexec().
Now, migrate_to_reboot_cpu() was originally written with the assumption that
any further code will not need to perform CPU hotplug, since we are anyway in
the reboot path. However, kexec is clearly not such a case, since we depend on
onlining CPUs, atleast on powerpc.
So re-enable cpu-hotplug after returning from migrate_to_reboot_cpu() in the
kexec path, to fix this regression in kexec on powerpc.
Also, wrap the cpu_up() in powerpc kexec code within a WARN_ON(), so that we
can catch such issues more easily in the future.
Fixes: c97102ba96 (kexec: migrate to reboot cpu)
Cc: stable@vger.kernel.org
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
With binutils 2.24, various 64 bit builds fail with relocation errors
such as
arch/powerpc/kernel/built-in.o: In function `exc_debug_crit_book3e':
(.text+0x165ee): relocation truncated to fit: R_PPC64_ADDR16_HI
against symbol `interrupt_base_book3e' defined in .text section
in arch/powerpc/kernel/built-in.o
arch/powerpc/kernel/built-in.o: In function `exc_debug_crit_book3e':
(.text+0x16602): relocation truncated to fit: R_PPC64_ADDR16_HI
against symbol `interrupt_end_book3e' defined in .text section
in arch/powerpc/kernel/built-in.o
The assembler maintainer says:
I changed the ABI, something that had to be done but unfortunately
happens to break the booke kernel code. When building up a 64-bit
value with lis, ori, shl, oris, ori or similar sequences, you now
should use @high and @higha in place of @h and @ha. @h and @ha
(and their associated relocs R_PPC64_ADDR16_HI and R_PPC64_ADDR16_HA)
now report overflow if the value is out of 32-bit signed range.
ie. @h and @ha assume you're building a 32-bit value. This is needed
to report out-of-range -mcmodel=medium toc pointer offsets in @toc@h
and @toc@ha expressions, and for consistency I did the same for all
other @h and @ha relocs.
Replacing @h with @high in one strategic location fixes the relocation
errors. This has to be done conditionally since the assembler either
supports @h or @high but not both.
Cc: <stable@vger.kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Pull virtio_blk fix from Jens Axboe:
"There's a start/stop queue race in virtio_blk, which causes stalls and
erratic behaviour for some. I've had this queued up for 3.16 for a
while, but I think we should push it into the current series as well.
So I cherry picked the commit and added a stable marker as well, so it
can propagate down"
* 'for-linus' of git://git.kernel.dk/linux-block:
virtio_blk: fix race between start and stop queue
Pull two timer fixes from Thomas Gleixner:
"Two small fixlets for ARM SoC clocksource drivers:
- avoid calling functions which might sleep from interrupt [disabled]
context in tcb_clksrc used on Atmel SoCs
- use irq_force_affinity() to pin the per cpu timer interrupt on a
not yet online cpu in the SiRFprimaII driver"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource: tcb_clksrc: Make tc_mode interrupt safe
clocksource: marco: Fix the affinity set for local timer of CPU1
A slightly larger set of fixes than we'd like at this point in the
release. Hopefully our very last batch before 3.15:
- OMAP:
* Fix boot regression with CPU_IDLE enabled
* Fixes for audio playback on OMAP5
* Clock rate setting fix for OMAP3
* Misc idle/PM fixes
- Exynos:
* Removal of a couple of power domains to work around issues with access
when they are powered down
* Enabling missing highspeed-i2c driver to make MMC regulators work
* Secondary CPU spin-up fix for 4212
* Remove MDMA1 engine to avoid conflicts on secure mode platforms
* A few other DT fixes
- Marvell:
* PCI-e fixes for clocks and resource allocation
+ a few other smaller fixes, add a MAINTAINERS entry for reset drivers, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=73IV
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A slightly larger set of fixes than we'd like at this point in the
release. Hopefully our very last batch before 3.15:
OMAP:
- Fix boot regression with CPU_IDLE enabled
- Fixes for audio playback on OMAP5
- Clock rate setting fix for OMAP3
- Misc idle/PM fixes
Exynos:
- Removal of a couple of power domains to work around issues with
access when they are powered down
- Enabling missing highspeed-i2c driver to make MMC regulators work
- Secondary CPU spin-up fix for 4212
- Remove MDMA1 engine to avoid conflicts on secure mode platforms
- A few other DT fixes
Marvell:
- PCI-e fixes for clocks and resource allocation
plus a few other smaller fixes, add a MAINTAINERS entry for reset
drivers, etc"
* tag 'fixes-for-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (21 commits)
MAINTAINERS: Add reset controller framework entry
ARM: trusted_foundations: fix compile error on non-SMP
ARM: at91: sam9260: fix compilation issues
ARM: mvebu: fix definitions of PCIe interfaces on Armada 38x
ARM: imx: fix error handling in ipu device registration
ARM: OMAP4: Fix the boot regression with CPU_IDLE enabled
ARM: dts: Keep LDO4 always ON for exynos5250-arndale board
ARM: dts: Fix SPI interrupt numbers for exynos5420
ARM: dts: fix incorrect ak8975 compatible for exynos4412-trats2 board
ARM: OMAP2+: Fix DMA hang after off-idle
ARM: OMAP2+: nand: Fix NAND on OMAP2 and OMAP3 boards
ARM: dts: Remove g2d_pd node for exynos5420
ARM: dts: Remove mau_pd node for exynos5420
ARM: exynos_defconfig: enable HS-I2C to fix for mmc partition mount
ARM: dts: disable MDMA1 node for exynos5420
ARM: EXYNOS: fix the secondary CPU boot of exynos4212
ARM: omap5: hwmod_data: Correct IDLEMODE for McPDM
ARM: mvebu: mvebu-soc-id: keep clock enabled if PCIe unit is enabled
ARM: mvebu: mvebu-soc-id: add missing clk_put() call
ARM: at91/dt: sam9260: correct external trigger value
...
the vt8500 driver was failing to update the output value
when the combined set direction output and set value was
executed.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=pdRP
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v3.15-4' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pinctrl fix from Linus Walleij:
"A single last pinctrl fix for the v3.15 series: the vt8500 driver was
failing to update the output value when the combined set direction
output and set value was executed"
* tag 'pinctrl-v3.15-4' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: vt8500: Ensure value reg is updated when setting direction
Pull slave-dmaengine fixes from Vinod Koul:
"We have three small fixes.
First one from Andy reverts the devm_request irq as we need to ensure
the tasklet is killed after irq is freed, so we need to do free irq in
our code. Other two from Arnd are fixing the compilation issue in
omap and sa11x0 drivers with ARM randconfigs"
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: sa11x0: remove broken #ifdef
dmaengine: omap: hide filter_fn for built-in drivers
dmaengine: dw: went back to plain {request,free}_irq() calls
When there isn't enough vring descriptor for adding to vq,
blk-mq will be put as stopped state until some of pending
descriptors are completed & freed.
Unfortunately, the vq's interrupt may come just before
blk-mq's BLK_MQ_S_STOPPED flag is set, so the blk-mq will
still be kept as stopped even though lots of descriptors
are completed and freed in the interrupt handler. The worst
case is that all pending descriptors are freed in the
interrupt handler, and the queue is kept as stopped forever.
This patch fixes the problem by starting/stopping blk-mq
with holding vq_lock.
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Jens Axboe <axboe@fb.com>
Conflicts:
drivers/block/virtio_blk.c
Pull AFS fixes and cleanups from David Howells:
"Here are some patches to the AFS filesystem:
1) Fix problems in the clean-up parts of the cache manager service
handler.
2) Split afs_end_call() introduced in (1) and replace some identical
code elsewhere with a call to the first half of the split function.
3) Fix an error introduced in the workqueue PREPARE_WORK() elimination
commits.
4) Clean up argument passing to functions called from the workqueue as
there's now an insulating layer between them and the workqueue.
This is possible from (3)"
* 'afs' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs:
AFS: Pass an afs_call* to call->async_workfn() instead of a work_struct*
AFS: Fix kafs module unloading
AFS: Part of afs_end_call() is identical to code elsewhere, so split it
AFS: Fix cache manager service handlers
The sum at the beginning of line "intr" includes also unnumbered
interrupts. It implies that the sum at the beginning isn't the sum
of the remainder of the line, not even an estimation.
Fixed the documentation to mention that.
This behaviour was added to /proc/stat in commit a2eddfa959 ("x86:
make /proc/stat account for all interrupts")
Signed-off-by: Jan Moskyto Matejka <mq@suse.cz>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The sample wrapper currently fails on some Java 7 .class files. This
updates the wrapper to properly handle those files.
Signed-off-by: Jonathan Callen <jcallen@gentoo.org>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Added setting to email-clients that is easier to read and is easier to
setup thunderbird. Removed config settings and added GUI settings.
Signed-off-by: Paul McQuade <paulmcquad@gmail.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is a single fix for a bug exposed by a sysfs change in 3.13 which now
causes libsas to trigger a warn on in device removal.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJTgKNGAAoJEDeqqVYsXL0ML98IALHiBnsPd8LqtLPDgCg7poBY
ci4gHgthKRMDiwSi847x6eXxXKDWgPfrMjiVL4pulAkNtAFh52c+BxUcAoEwgSpj
WmFJwFYwNzExhvOM6my42e1D60G3Gu1DvwrdP065ajygjBZl4beMF06ZWrz+6UxF
WMpCVw4Rmu8PdAm8aH5N13Sl71nIY6W/rlbC/CtrGLelB7Om1gPbr9YpPfISLFdn
1A99lJEKjDvZNk64BhJtnRCgvzBWzJ4TVEmnWIx/2mJe/z0pM7whYIKAbqX2WgCi
JrZ/rdCDJe+lq/rVhCVU/enEoqJsbtWjF6+Wp7/0lK0PDvfSXyR92KfCIXCFi4A=
=HAcQ
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull single scsi fix from James Bottomley:
"This is a single fix for a bug exposed by a sysfs change in 3.13 which
now causes libsas to trigger a warn on in device removal"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
[SCSI] scsi_transport_sas: move bsg destructor into sas_rphy_remove
Pull two nfsd bugfixes from Bruce Fields:
"Just two bugfixes, one for a merge-window-introduced ACL regression,
the other for a longer-standing v4 state bug"
* 'for-3.15' of git://linux-nfs.org/~bfields/linux:
nfsd4: warn on finding lockowner without stateid's
nfsd4: remove lockowner when removing lock stateid
nfsd4: fix corruption on setting an ACL.
The mapping from OF device IDs to platform device IDs is wrong.
TYPE_NCPXXWB473 is 0, TYPE_NCPXXWL333 is 1, so
ntc_thermistor_id[TYPE_NCPXXWB473] is { "ncp15wb473", TYPE_NCPXXWB473 }
while
ntc_thermistor_id[TYPE_NCPXXWL333] is { "ncp18wb473", TYPE_NCPXXWB473 }.
So the name is wrong for all but the "ntc,ncp15wb473" entry, and the
type is wrong for the "ntc,ncp15wl333" entry.
So map the entries by index, it is neither elegant nor robust but at
least it is correct.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Fixes: 9e8269de hwmon: (ntc_thermistor) Add DT with IIO support to NTC thermistor driver
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Cc: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Cc: Doug Anderson <dianders@chromium.org>
In commit 9e8269de, support was added for ntc_thermistor devices being
declared in the device tree and implemented on top of IIO. With that
change, a dependency was added to the ntc_thermistor driver:
depends on (!OF && !IIO) || (OF && IIO)
This construct has the drawback that the driver can no longer be
selected when OF is set and IIO isn't, nor when IIO is set and OF is
not. This is a regression for the original users of the driver.
As the new code depends on IIO and is useless without OF, include it
only if both are enabled, and set the dependencies accordingly. This
is clearer, more simple and more correct.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Fixes: 9e8269de hwmon: (ntc_thermistor) Add DT with IIO support to NTC thermistor driver
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Cc: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Cc: Doug Anderson <dianders@chromium.org>
The temp[1-*]_min_hyst sysfs attribute is already implemented by 3
hwmon drivers (adt7x10, lm77 and lm92) but was missing from the
standard interface.
Also add temp[1-*]_lcrit_hyst for consistency, even though no driver
implement that one for the time being.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
1/ async_mult() sometimes maps less buffers than initially requested.
We end up freeing dmaengine_unmap_data on an invalid pool.
2/ mv_xor: register write ordering fix
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=XFIL
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-fixes-3.15-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/dmaengine
Pull dmaengine fixes from Dan Williams:
"Two fixes for -stable:
- async_mult() sometimes maps less buffers than initially requested.
We end up freeing dmaengine_unmap_data on an invalid pool.
- mv_xor: register write ordering fix"
* tag 'dmaengine-fixes-3.15-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/dmaengine:
dmaengine: fix dmaengine_unmap failure
dma: mv_xor: Flush descriptors before activating a channel
Pull sparc fixes from David Miller:
"A small bunch of bug fixes, in particular:
1) On older cpus we need a different chunk of virtual address space
to map the huge page TSB.
2) Missing memory barrier in Niagara2 memcpy.
3) trinity showed some places where fault validation was
unnecessarily loud on sparc64
4) Some sysfs printf's need a type adjustment, from Toralf Förster"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc64: fix format string mismatch in arch/sparc/kernel/sysfs.c
sparc64: Add membar to Niagara2 memcpy code.
sparc64: Fix huge TSB mapping on pre-UltraSPARC-III cpus.
sparc64: Don't bark so loudly about 32-bit tasks generating 64-bit fault addresses.
Pull networking fixes from David Miller:
"It looks like a sizeble collection but this is nearly 3 weeks of bug
fixing while you were away.
1) Fix crashes over IPSEC tunnels with NAT, the latter can reroute
the packet through a non-IPSEC protected path and the code has to
be able to handle SKBs attached to routes lacking an attached xfrm
state. From Steffen Klassert.
2) Fix OOPSs in ipv4 and ipv6 ipsec layers for unsupported
sub-protocols, also from Steffen Klassert.
3) Set local_df on fragmented netfilter skbs otherwise we won't be
able to forward successfully, from Florian Westphal.
4) cdc_mbim ipv6 neighbour code does __vlan_find_dev_deep without
holding RCU lock, from Bjorn Mork.
5) local_df test in ip_may_fragment is inverted, from Florian
Westphal.
6) jme driver doesn't check for DMA mapping failures, from Neil
Horman.
7) qlogic driver doesn't calculate number of TX queues properly, from
Shahed Shaikh.
8) fib_info_cnt can drift irreversibly positive if we fail to
allocate the fi->fib_metrics array, from Sergey Popovich.
9) Fix use after free in ip6_route_me_harder(), also from Sergey
Popovich.
10) When SYSCTL is disabled, we don't handle local_port_range and
ping_group_range defaults properly at all, from Cong Wang.
11) Unaccelerated VLAN tagged frames improperly handled by cdc_mbim
driver, fix from Bjorn Mork.
12) cassini driver needs nested lock annotations for TX locking, from
Emil Goode.
13) On init error ipv6 VTI driver can unregister pernet ops twice,
oops. Fix from Mahtias Krause.
14) If macvlan device is down, don't propagate IFF_ALLMULTI changes,
from Peter Christensen.
15) Missing NULL pointer check while parsing netlink config options in
ip6_tnl_validate(). From Susant Sahani.
16) Fix handling of neighbour entries during ipv6 router reachability
probing, from Duan Jiong.
17) x86 and s390 JIT address randomization has some address
calculation bugs leading to crashes, from Alexei Starovoitov and
Heiko Carstens.
18) Clear up those uglies with nop patching and net_get_random_once(),
from Hannes Frederic Sowa.
19) Option length miscalculated in ip6_append_data(), fix also from
Hannes Frederic Sowa.
20) A while ago we fixed a race during device unregistry when a
namespace went down, turns out there is a second place that needs
similar protection. From Cong Wang.
21) In the new Altera TSE driver multicast filtering isn't working,
disable it and just use promisc mode until the cause is found.
From Vince Bridgers.
22) When we disable router enabling in ipv6 we have to flush the
cached routes explicitly, from Duan Jiong.
23) NBMA tunnels should not cache routes on the tunnel object because
the key is variable, from Timo Teräs.
24) With stacked devices GRO information in skb->cb[] can be not setup
properly, make sure it is in all code paths. From Eric Dumazet.
25) Really fix stacked vlan locking, multiple levels of nesting with
intervening non-vlan devices are possible. From Vlad Yasevich.
26) Fallback ipip tunnel device's mtu is not setup properly, from
Steffen Klassert.
27) The packet scheduler's tcindex filter can crash because we
structure copy objects with list_head's inside, oops. From Cong
Wang.
28) Fix CHECKSUM_COMPLETE handling for ipv6 GRE tunnels, from Eric
Dumazet.
29) In some configurations 'itag' in __mkroute_input() can end up
being used uninitialized because of how fib_validate_source()
works. Fix it by explitly initializing itag to zero like all the
other fib_validate_source() callers do, from Li RongQing"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (116 commits)
batman: fix a bogus warning from batadv_is_on_batman_iface()
ipv4: initialise the itag variable in __mkroute_input
bonding: Send ALB learning packets using the right source
bonding: Don't assume 802.1Q when sending alb learning packets.
net: doc: Update references to skb->rxhash
stmmac: Remove unbalanced clk_disable call
ipv6: gro: fix CHECKSUM_COMPLETE support
net_sched: fix an oops in tcindex filter
can: peak_pci: prevent use after free at netdev removal
ip_tunnel: Initialize the fallback device properly
vlan: Fix build error wth vlan_get_encap_level()
can: c_can: remove obsolete STRICT_FRAME_ORDERING Kconfig option
MAINTAINERS: Pravin Shelar is Open vSwitch maintainer.
bnx2x: Convert return 0 to return rc
bonding: Fix alb mode to only use first level vlans.
bonding: Fix stacked device detection in arp monitoring
macvlan: Fix lockdep warnings with stacked macvlan devices
vlan: Fix lockdep warning with stacked vlan devices.
net: Allow for more then a single subclass for netif_addr_lock
net: Find the nesting level of a given device by type.
...
The setup_max_cpus variable is only defined if CONFIG_SMP is set. Add
a preprocessor condition to avoid the following compilation error if
CONFIG_SMP is not set:
arch/arm/include/asm/trusted_foundations.h: In function 'register_trusted_foundations':
arch/arm/include/asm/trusted_foundations.h:57:2: error: 'setup_max_cpus' undeclared (first use in this function)
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Pull scheduler fixes from Ingo Molnar:
"The biggest commit is an irqtime accounting loop latency fix, the rest
are misc fixes all over the place: deadline scheduling, docs, numa,
balancer and a bad to-idle latency fix"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/numa: Initialize newidle balance stats in sd_numa_init()
sched: Fix updating rq->max_idle_balance_cost and rq->next_balance in idle_balance()
sched: Skip double execution of pick_next_task_fair()
sched: Use CPUPRI_NR_PRIORITIES instead of MAX_RT_PRIO in cpupri check
sched/deadline: Fix memory leak
sched/deadline: Fix sched_yield() behavior
sched: Sanitize irq accounting madness
sched/docbook: Fix 'make htmldocs' warnings caused by missing description
Pull perf fixes from Ingo Molnar:
"The biggest changes are fixes for races that kept triggering Trinity
crashes, plus liblockdep build fixes and smaller misc fixes.
The liblockdep bits in perf/urgent are a pull mistake - they should
have been in locking/urgent - but by the time I noticed other commits
were added and testing was done :-/ Sorry about that"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf: Fix a race between ring_buffer_detach() and ring_buffer_attach()
perf: Prevent false warning in perf_swevent_add
perf: Limit perf_event_attr::sample_period to 63 bits
tools/liblockdep: Remove all build files when doing make clean
tools/liblockdep: Build liblockdep from tools/Makefile
perf/x86/intel: Fix Silvermont's event constraints
perf: Fix perf_event_init_context()
perf: Fix race in removing an event
Pull drm radeon and nouveau fixes from Dave Airlie:
"Fixes for the other big two.
The radeon VCE one is large but it fixes some userspace triggerable
issues, otherwise its blackscreens and oopses.
Nouveau fixes a bleeding laptop panel issue when displayport is used
sometimes"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon/pm: don't allow debugfs/sysfs access when PX card is off (v2)
drm/radeon: avoid segfault on device open when accel is not working.
drm/radeon: fix typo in finding PLL params
drm/radeon: fix register typo on si
drm/radeon: fix buffer placement under memory pressure v2
drm/radeon: fix page directory update size estimation
drm/radeon: handle non-VGA class pci devices with ATRM
drm/radeon: fix DCE83 check for mullins
drm/radeon: check VCE relocation buffer range v3
drm/radeon: also try GART for CPU accessed buffers
drm/gf119-/disp: fix nasty bug which can clobber SOR0's clock setup
drm/nvd9/therm: handle another kind of PWM fan
Merge misc fixes from Andrew Morton:
"9 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
MAINTAINERS: add closing angle bracket to Vince Bridgers' email address
Documentation: fix DOCBOOKS=... building
ocfs2: fix double kmem_cache_destroy in dlm_init
mm/memory-failure.c: fix memory leak by race between poison and unpoison
wait: swap EXIT_ZOMBIE(Z) and EXIT_DEAD(X) chars in TASK_STATE_TO_CHAR_STR
memcg: fix swapcache charge from kernel thread context
mm: madvise: fix MADV_WILLNEED on shmem swapouts
mm/filemap.c: avoid always dirtying mapping->flags on O_DIRECT
hwpoison, hugetlb: lock_page/unlock_page does not match for handling a free hugepage
Prior to commit 4266129964 ("[media] DocBook: Move all media docbook
stuff into its own directory") it was possible to build only a single
(or more) book(s) by calling, for example
make htmldocs DOCBOOKS=80211.xml
This now fails:
cp: target `.../Documentation/DocBook//media_api' is not a directory
Ignore errors from that copy to make this possible again.
Fixes: 4266129964 ("[media] DocBook: Move all media docbook stuff into its own directory")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In dlm_init, if create dlm_lockname_cache failed in
dlm_init_master_caches, it will destroy dlm_lockres_cache which created
before twice. And this will cause system die when loading modules.
Signed-off-by: Joseph Qi <joseph.qi@huawei.com>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Joel Becker <jlbec@evilplan.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When a memory error happens on an in-use page or (free and in-use)
hugepage, the victim page is isolated with its refcount set to one.
When you try to unpoison it later, unpoison_memory() calls put_page()
for it twice in order to bring the page back to free page pool (buddy or
free hugepage list). However, if another memory error occurs on the
page which we are unpoisoning, memory_failure() returns without
releasing the refcount which was incremented in the same call at first,
which results in memory leak and unconsistent num_poisoned_pages
statistics. This patch fixes it.
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: <stable@vger.kernel.org> [2.6.32+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In commit ad86622b47 ("wait: swap EXIT_ZOMBIE and EXIT_DEAD to hide
EXIT_TRACE from user-space") the order of task state definitions were
changed: EXIT_DEAD and EXIT_ZOMBIE were swapped. Though the charterers
for the states in TASK_STATE_TO_CHAR_STR string were not updated. This
patch synchronizes the string to the order of definitions.
Signed-off-by: Masatake YAMATO <yamato@redhat.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 284f39afea ("mm: memcg: push !mm handling out to page cache
charge function") explicitly checks for page cache charges without any
mm context (from kernel thread context[1]).
This seemed to be the only possible case where memory could be charged
without mm context so commit 03583f1a63 ("memcg: remove unnecessary
!mm check from try_get_mem_cgroup_from_mm()") removed the mm check from
get_mem_cgroup_from_mm(). This however caused another NULL ptr
dereference during early boot when loopback kernel thread splices to
tmpfs as reported by Stephan Kulow:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000360
IP: get_mem_cgroup_from_mm.isra.42+0x2b/0x60
Oops: 0000 [#1] SMP
Modules linked in: btrfs dm_multipath dm_mod scsi_dh multipath raid10 raid456 async_raid6_recov async_memcpy async_pq raid6_pq async_xor xor async_tx raid1 raid0 md_mod parport_pc parport nls_utf8 isofs usb_storage iscsi_ibft iscsi_boot_sysfs arc4 ecb fan thermal nfs lockd fscache nls_iso8859_1 nls_cp437 sg st hid_generic usbhid af_packet sunrpc sr_mod cdrom ata_generic uhci_hcd virtio_net virtio_blk ehci_hcd usbcore ata_piix floppy processor button usb_common virtio_pci virtio_ring virtio edd squashfs loop ppa]
CPU: 0 PID: 97 Comm: loop1 Not tainted 3.15.0-rc5-5-default #1
Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
Call Trace:
__mem_cgroup_try_charge_swapin+0x40/0xe0
mem_cgroup_charge_file+0x8b/0xd0
shmem_getpage_gfp+0x66b/0x7b0
shmem_file_splice_read+0x18f/0x430
splice_direct_to_actor+0xa2/0x1c0
do_lo_receive+0x5a/0x60 [loop]
loop_thread+0x298/0x720 [loop]
kthread+0xc6/0xe0
ret_from_fork+0x7c/0xb0
Also Branimir Maksimovic reported the following oops which is tiggered
for the swapcache charge path from the accounting code for kernel threads:
CPU: 1 PID: 160 Comm: kworker/u8:5 Tainted: P OE 3.15.0-rc5-core2-custom #159
Hardware name: System manufacturer System Product Name/MAXIMUSV GENE, BIOS 1903 08/19/2013
task: ffff880404e349b0 ti: ffff88040486a000 task.ti: ffff88040486a000
RIP: get_mem_cgroup_from_mm.isra.42+0x2b/0x60
Call Trace:
__mem_cgroup_try_charge_swapin+0x45/0xf0
mem_cgroup_charge_file+0x9c/0xe0
shmem_getpage_gfp+0x62c/0x770
shmem_write_begin+0x38/0x40
generic_perform_write+0xc5/0x1c0
__generic_file_aio_write+0x1d1/0x3f0
generic_file_aio_write+0x4f/0xc0
do_sync_write+0x5a/0x90
do_acct_process+0x4b1/0x550
acct_process+0x6d/0xa0
do_exit+0x827/0xa70
kthread+0xc3/0xf0
This patch fixes the issue by reintroducing mm check into
get_mem_cgroup_from_mm. We could do the same trick in
__mem_cgroup_try_charge_swapin as we do for the regular page cache path
but it is not worth troubles. The check is not that expensive and it is
better to have get_mem_cgroup_from_mm more robust.
[1] - http://marc.info/?l=linux-mm&m=139463617808941&w=2
Fixes: 03583f1a63 ("memcg: remove unnecessary !mm check from try_get_mem_cgroup_from_mm()")
Reported-and-tested-by: Stephan Kulow <coolo@suse.com>
Reported-by: Branimir Maksimovic <branimir.maksimovic@gmail.com>
Signed-off-by: Michal Hocko <mhocko@suse.cz>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
MADV_WILLNEED currently does not read swapped out shmem pages back in.
Commit 0cd6144aad ("mm + fs: prepare for non-page entries in page
cache radix trees") made find_get_page() filter exceptional radix tree
entries but failed to convert all find_get_page() callers that WANT
exceptional entries over to find_get_entry(). One of them is shmem swap
readahead in madvise, which now skips over any swap-out records.
Convert it to find_get_entry().
Fixes: 0cd6144aad ("mm + fs: prepare for non-page entries in page cache radix trees")
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Reported-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In some testing I ran today (some fio jobs that spread over two nodes),
we end up spending 40% of the time in filemap_check_errors(). That
smells fishy. Looking further, this is basically what happens:
blkdev_aio_read()
generic_file_aio_read()
filemap_write_and_wait_range()
if (!mapping->nr_pages)
filemap_check_errors()
and filemap_check_errors() always attempts two test_and_clear_bit() on
the mapping flags, thus dirtying it for every single invocation. The
patch below tests each of these bits before clearing them, avoiding this
issue. In my test case (4-socket box), performance went from 1.7M IOPS
to 4.0M IOPS.
Signed-off-by: Jens Axboe <axboe@fb.com>
Acked-by: Jeff Moyer <jmoyer@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For handling a free hugepage in memory failure, the race will happen if
another thread hwpoisoned this hugepage concurrently. So we need to
check PageHWPoison instead of !PageHWPoison.
If hwpoison_filter(p) returns true or a race happens, then we need to
unlock_page(hpage).
Signed-off-by: Chen Yucong <slaoub@gmail.com>
Reviewed-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Tested-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Reviewed-by: Andi Kleen <ak@linux.intel.com>
Cc: <stable@vger.kernel.org> [2.6.36+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The 'renameat2()' system call was incorrectly added as a ENTRY_COMP() in
the parisc system call table by commit 18e480aa07 ("parisc: add
renameat2 syscall"). That causes a link-time error due to there not
being any compat version of that system call:
arch/parisc/kernel/built-in.o: In function `sys_call_table':
(.rodata+0xad0): undefined reference to `compat_sys_renameat2'
make: *** [vmlinux] Error 1
Easily fixed by marking the system call as being the same for compat as
for native by using ENTRY_SAME() instead of ENTRY_COMP().
Reported-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Miklos Szeredi <miklos@szeredi.hu>
Acked-by: Helge Deller <deller@gmx.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- two fixes concerning iio ADC triggers for at91sam9260 and at91sam9g20
one for the "device" file, the other for the DT.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJTfjD/AAoJEAf03oE53VmQ1p0IAJL/FmsbXfHLLu8KvQEXMW8W
Y3c22v2mHSHpEFjqjFg+LbOkRbFaPTlszSXuKyw7HJPiOygUk/C1i2MUW4WLNlyY
fqu+tiAOrcfJ8rapM5ndFdeMZrkyRQIInFEPzOttQJSN4Aczpc6irfMqOOqw0y/s
Sf88MiK2YgeXnt5dH6mDYhy29glvspek3w1FmDN3DjmiAdxAUV8bSpOmw2FsFAX7
QJOwkevln+3Ddxnq+NsG/6KxdAl0fj+G3shl4GwALr+hizKypzsFsSGDuyKuAL2o
A7e+OFoUWN8eCTJBdP9YA/lVyl83uFMM3tBcHr4Oq8dJk6sQ0GNQcdJuCUBGTBw=
=ehhW
-----END PGP SIGNATURE-----
Merge tag 'at91-fixes2' of git://github.com/at91linux/linux-at91 into fixes
Second 3.15 fixes for AT91
- two fixes concerning iio ADC triggers for at91sam9260 and at91sam9g20
one for the "device" file, the other for the DT.
* tag 'at91-fixes2' of git://github.com/at91linux/linux-at91:
ARM: at91: sam9260: fix compilation issues
ARM: at91/dt: sam9260: correct external trigger value
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
call->async_workfn() can take an afs_call* arg rather than a work_struct* as
the functions assigned there are now called from afs_async_workfn() which has
to call container_of() anyway.
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Nathaniel Wesley Filardo <nwf@cs.jhu.edu>
Reviewed-by: Tejun Heo <tj@kernel.org>
At present, it is not possible to successfully unload the kafs module if there
are outstanding async outgoing calls (those made with afs_make_call()). This
appears to be due to the changes introduced by:
commit 059499453a
Author: Tejun Heo <tj@kernel.org>
Date: Fri Mar 7 10:24:50 2014 -0500
Subject: afs: don't use PREPARE_WORK
which didn't go far enough. The problem is due to:
(1) The aforementioned commit introduced a separate handler function pointer
in the call, call->async_workfn, in addition to the original workqueue
item, call->async_work, for asynchronous operations because workqueues
subsystem cannot handle the workqueue item pointer being changed whilst
the item is queued or being processed.
(2) afs_async_workfn() was introduced in that commit to be the callback for
call->async_work. Its sole purpose is to run whatever call->async_workfn
points to.
(3) call->async_workfn is only used from afs_async_workfn(), which is only
set on async_work by afs_collect_incoming_call() - ie. for incoming
calls.
(4) call->async_workfn is *not* set by afs_make_call() when outgoing calls are
made, and call->async_work is set afs_process_async_call() - and not
afs_async_workfn().
(5) afs_process_async_call() now changes call->async_workfn rather than
call->async_work to point to afs_delete_async_call() to clean up, but this
is only effective for incoming calls because call->async_work does not
point to afs_async_workfn() for outgoing calls.
(6) Because, for incoming calls, call->async_work remains pointing to
afs_process_async_call() this results in an infinite loop.
Instead, make the workqueue uniformly vector through call->async_workfn, via
afs_async_workfn() and simply initialise call->async_workfn to point to
afs_process_async_call() in afs_make_call().
Signed-off-by: Nathaniel Wesley Filardo <nwf@cs.jhu.edu>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Tejun Heo <tj@kernel.org>
Split afs_end_call() into two pieces, one of which is identical to code in
afs_process_async_call(). Replace the latter with a call to the first part of
afs_end_call().
Signed-off-by: Nathaniel Wesley Filardo <nwf@cs.jhu.edu>
Signed-off-by: David Howells <dhowells@redhat.com>
The recent change in sysfs, bcdde7e221
"sysfs: make __sysfs_remove_dir() recursive" revealed an asymmetric
rphy device creation/deletion sequence in scsi_transport_sas:
modprobe mpt2sas
sas_rphy_add
device_add A rphy->dev
device_add B sas_device transport class
device_add C sas_end_device transport class
device_add D bsg class
rmmod mpt2sas
sas_rphy_delete
sas_rphy_remove
device_del B
device_del C
device_del A
sysfs_remove_group recursive sysfs dir removal
sas_rphy_free
device_del D warning
where device A is the parent of B, C, and D.
When sas_rphy_free tries to unregister the bsg request queue (device D
above), the ensuing sysfs cleanup discovers that its sysfs group has
already been removed and emits a warning, "sysfs group... not found for
kobject 'end_device-X:0'".
Since bsg creation is a side effect of sas_rphy_add, move its
complementary removal call into sas_rphy_remove. This imposes the
following tear-down order for the devices above: D, B, C, A.
Note the sas_device and sas_end_device transport class devices (B and C
above) are created and destroyed both via the list match traversal in
attribute_container_device_trigger, so the order in which they are
handled is fixed. This is fine as long as they are deleted before their
parent device.
Signed-off-by: Joe Lawrence <joe.lawrence@stratus.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Current code only touches the direction register when setting direction
to output, which breaks logic like
echo high > /sys/class/gpio/gpio0/direction
which is expected to also set the value. This patch also adds a call
to update the value register when setting direction to output.
Signed-off-by: Alexey Charkov <alchark@gmail.com>
Acked-by: Tony Prisk <linux@prisktech.co.nz>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
batman tries to search dev->iflink to check if it's a batman interface,
but ->iflink could be 0, which is not a valid ifindex. It should just
avoid iflink == 0 case.
Reported-by: Jet Chen <jet.chen@intel.com>
Tested-by: Jet Chen <jet.chen@intel.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Cc: Antonio Quartulli <antonio@open-mesh.com>
Cc: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
