Sometimes, a VF driver will lose PCIe address access, such as due to
a PF FLR event. In fm10k_detach_subtask, poll and check whether the
PCIe register space is active again and restore the device when it has.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If an FLR occurs, VF devices will be knocked out of bus master mode, and
the driver will be unable to recover from the reset properly, resulting
in malicious driver events and an infinite reset loop. In the normal
case, the bus master mode will already be enabled and this call will
essentially be a no-op. Since we're doing this every reset, it is
possible we could remove the other calls to pci_set_master() but it
seems not harmful to just leave them in place.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Continuing the effort to commonize the similar suspend/resume flows,
finish up by using the new fm10k_handle_suspand and fm10k_handle_resume
functions for the standard suspend/resume flow.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When a function level PCI reset is triggered using sysfs, it calls the
driver's .reset_notify error handler. Implement a handler based on the
now split fm10k_prepare_for_reset and fm10k_handle_reset functions, so
that we fully reset the driver when the PCI function level reset occurs.
This also ensures the reset is handled in a clean way by first disabling
all the driver bits first and then restoring them after the function
reset. Previously the stack simply performed a blind function reset and
our driver didn't take any part in the process.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Now that we have extracted the necessary steps for a split
suspend/resume flow, re-use these functions instead of using the current
open coded flow. This ensures that we don't miss any steps. It also
ensures that we have the correct driver states set.
Since we'll be handling all of the reset flow ourselves, we no longer
need to request a reset in the io_slot_reset() function.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Implement fm10k_prepare_suspend and fm10k_handle_resume functions which
abstract around the now existing fm10k_prepare_for_reset and
fm10k_handle_reset. The new functions also handle stopping the service
task, which is something that the original re-init flow does not need.
Every other location that does a suspend/resume type flow is expected to
use these functions, because otherwise they may have conflicts with the
running watchdog routines. This also has the effect of preventing
possible surprise remove events during handling of FLR events and PCIe
errors.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There are several flows in the driver which perform the similar function
of tearing down software and restoring software to recover from certain
errors or PCIe events, including:
* fm10k_reinit
* fm10k_suspend/resume
* fm10k_io_error_detected/fm10k_io_resume
In addition, we want to implement a .reset_notify() handler as well
which will also perform similar function.
Rework how the driver codes reset and resume flows by separating out the
reinit logic into two functions "fm10k_prepare_for_reset" and
"fm10k_handle_reset". This first step will allow us to re-use this
functionality in the similar blocks of code instead of re-coding the
same sequence of events slightly different.
The end result should be more maintainable and correct, fixing several
inconsistencies with the work flow.
The new functions expect to take the rtnl_lock() themselves, and it does
have the unfortunate side effect of having the reinit flow take then
release then take the rtnl_lock. However, this minor downside is
out weighted by the benefits of code reduction and reducing needless
difference between these flows.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
It turns out that sometimes during a reset the Tx queues will be
temporarily stuck longer than .stop_hw() expects. Work around this issue
by attempting to .stop_hw() first. If it tails, wait a number of
attempts until the Tx queues appear to be drained. After this, attempt
stop_hw() again. This ensures that we avoid waiting if we don't need to,
such as during the first initialization of a VF, and give the proper
amount of time necessary to recover from most situations. It is possible
that the hardware is actually stuck. For PFs, this is usually fixed by
a datapath reset. Unfortunately the VF cannot request a similar reset
for itself.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When stop_hw() routine fails with FM10K_ERR_REQUESTS_PENDING, this
indicates that the Tx or Rx queues did not shutdown within the time
limit. Print a more suitable message at the dev_info level instead of
dev_err.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A while ago, an additional check for the switch being ready was added to
reset_hw. A recent refactor accidentally made this check return an error
code on failure which caused fm10k_probe to fail when the switch wasn't
brought up first. The original reasoning for the check was to prevent
additional data path reset when the fabric wasn't ready yet. However,
there isn't a compelling reason to keep the check, as the data path
reset will restore hardware to a known good state. Remove the check and
perform the data path reset regardless of the switch manager state.
An alternative fix is to return FM10K_SUCCESS instead, and bypass the
actual data path reset. This should be fine as we will perform
a reset_hw once the switch is active. However, since data path reset
will reset many parts of the hardware it seems better to just perform
the reset regardless of switch state.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Don't report FM10K_ERR_REQUESTS_PENDING when we fail to disable queues
within the timeout. This can occur due to a hardware Tx hang, or when
the switch ethernet fabric is resetting while we are transmitting
traffic. It can sometimes take up to 500ms before the Tx DMA engine
gives up. Instead, just skip the DMA engine check and perform
a data-path reset anyways. Add a statistic counter to keep track of the
number of resets occurring while we have pending DMA on the rings.
In order to prevent having to re-assign err to 0, re-order the
last few items of the reset_hw_pf function so that we don't perform
"return err" at the end.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When a data path reset is initiated, write control to the PCIE_GMBX is
yanked from the switch manager. The switch manager writes to this
register to clear mailbox global interrupt bits as part of its mailbox
interrupt handling routine. When the device recovers from the data path
reset and these bits are not cleared, it will prevent future mailbox
global interrupts from being triggered. Upon confirming that the device
has exited from a data path reset, clear these bits to ensure the proper
functioning of the mailbox global interrupt.
Signed-off-by: Ngai-Mint Kwan <ngai-mint.kwan@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Also prevent updating stats while the interface is down. If we're
already updating stats, just return doing nothing. When we take the
device down, block stat updates until we come back up. This ensures that
we avoid tearing down rings when we're updating statistics, and prevents
updating statistics until we're up.
We can't re-use the __FM10K_DOWN for this because it wouldn't prevent
multiple threads from accessing statistics. Neither does it prevent the
case where we start updating stats and then start going down in another
thread.
The fm10k_get_stats64 is except from this, because it has a completely
different flow which does not suffer from the same issues as
fm10k_update_stats might.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
It's currently possible for fm10k_update_stats to be called during the
window when we go down and the rings are removed. This can result in
a null pointer dereference. In fm10k_get_stats64 we work around this by
using ACCESS_ONCE and a null pointer check inside the loop. Use this
same flow in the fm10k_update_stats to avoid the potential null pointer.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Return early from fm10k_down() when we are already down, since that
means another thread is either already finished or has started going
down, so shouldn't conflict with them.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Expose the transmit queue length of each traffic class and the amount of
unicast packets discarded due to insufficient room in the shared buffer.
The first counter allows us to debug user priority to traffic class
mapping, whereas the drop counter is useful when determining shared buffer
configuration.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Expose per-priority bytes / packets / PFC packets counters via ethtool.
These counters are very useful when debugging QoS functionality and
provide a better insight into the device's forwarding plane.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the missing free_netdev() before return from function
cpmac_probe() in the error handling case.
This patch revert commit 0465be8f4f ("net: cpmac: fix in
releasing resources"), which changed to only free_netdev
while register_netdev failed.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use PTR_ERR_OR_ZERO rather than if(IS_ERR(...)) + PTR_ERR.
Generated by: scripts/coccinelle/api/ptr_ret.cocci
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ops->reset() error handling case, clk_disable_unprepare() is missed
before return from this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
module_platform_driver() makes the code simpler by eliminating
boilerplate code.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove .owner field if calls are used which set it automatically.
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of error, the function of_parse_phandle() returns NULL
pointer not ERR_PTR(). The IS_ERR() test in the return value
check should be replaced with NULL test.
Fixes: 46aa27df88 ('net: axienet: Use devm_* calls')
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
A user will now be able to loop packets back out of the same port using
a bpf program attached to xdp hook. Updates to the packet contents from
the bpf program is also supported.
For the packet write feature to work, the rx buffers are now mapped as
bidirectional when the page is allocated. This occurs only when the xdp
hook is active.
When the program returns a TX action, enqueue the packet directly to a
dedicated tx ring, so as to avoid completely any locking. This requires
the tx ring to be allocated 1:1 for each rx ring, as well as the tx
completion running in the same softirq.
Upon tx completion, this dedicated tx ring recycles pages without
unmapping directly back to the original rx ring. In steady state tx/drop
workload, effectively 0 page allocs/frees will occur.
In order to separate out the paths between free and recycle, a
free_tx_desc func pointer is introduced that is optionally updated
whenever recycle_ring is activated. By default the original free
function is always initialized.
Signed-off-by: Brenden Blanco <bblanco@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for writing the tx descriptor from multiple functions,
create a helper for both normal and blueflame access.
Signed-off-by: Brenden Blanco <bblanco@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mlx4 driver by default allocates order-3 pages for the ring to
consume in multiple fragments. When the device has an xdp program, this
behavior will prevent tx actions since the page must be re-mapped in
TODEVICE mode, which cannot be done if the page is still shared.
Start by making the allocator configurable based on whether xdp is
running, such that order-0 pages are always used and never shared.
Since this will stress the page allocator, add a simple page cache to
each rx ring. Pages in the cache are left dma-mapped, and in drop-only
stress tests the page allocator is eliminated from the perf report.
Note that setting an xdp program will now require the rings to be
reconfigured.
Before:
26.91% ksoftirqd/0 [mlx4_en] [k] mlx4_en_process_rx_cq
17.88% ksoftirqd/0 [mlx4_en] [k] mlx4_en_alloc_frags
6.00% ksoftirqd/0 [mlx4_en] [k] mlx4_en_free_frag
4.49% ksoftirqd/0 [kernel.vmlinux] [k] get_page_from_freelist
3.21% swapper [kernel.vmlinux] [k] intel_idle
2.73% ksoftirqd/0 [kernel.vmlinux] [k] bpf_map_lookup_elem
2.57% swapper [mlx4_en] [k] mlx4_en_process_rx_cq
After:
31.72% swapper [kernel.vmlinux] [k] intel_idle
8.79% swapper [mlx4_en] [k] mlx4_en_process_rx_cq
7.54% swapper [kernel.vmlinux] [k] poll_idle
6.36% swapper [mlx4_core] [k] mlx4_eq_int
4.21% swapper [kernel.vmlinux] [k] tasklet_action
4.03% swapper [kernel.vmlinux] [k] cpuidle_enter_state
3.43% swapper [mlx4_en] [k] mlx4_en_prepare_rx_desc
2.18% swapper [kernel.vmlinux] [k] native_irq_return_iret
1.37% swapper [kernel.vmlinux] [k] menu_select
1.09% swapper [kernel.vmlinux] [k] bpf_map_lookup_elem
Signed-off-by: Brenden Blanco <bblanco@plumgrid.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the BPF_PROG_TYPE_XDP hook in mlx4 driver.
In tc/socket bpf programs, helpers linearize skb fragments as needed
when the program touches the packet data. However, in the pursuit of
speed, XDP programs will not be allowed to use these slower functions,
especially if it involves allocating an skb.
Therefore, disallow MTU settings that would produce a multi-fragment
packet that XDP programs would fail to access. Future enhancements could
be done to increase the allowable MTU.
The xdp program is present as a per-ring data structure, but as of yet
it is not possible to set at that granularity through any ndo.
Signed-off-by: Brenden Blanco <bblanco@plumgrid.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bogus PHY interrupts are observed. This masks the PHY interrupt
when the interface works in NCSI mode as there is no attached
PHY under the circumstance.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Acked-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This matches the driver with devices compatible with "faraday,ftgmac100"
declared in the device tree. Originally, device's name from device
tree for it.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Acked-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes ftgmac100 driver support NCSI mode. The NCSI is enabled
on the interface if property "use-nc-si" or "use-ncsi" is found from
the device node in device tree.
* No PHY device is used when NCSI mode is enabled.
* The NCSI device (struct ncsi_dev) is created when probing the
device while it's enabled/started when the interface is brought
up.
* Hardware IP checksum dosn't work when NCSI mode is enabled. It
is disabled on enabled NCSI.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Acked-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device is assigned with random MAC address. It isn't reasonable.
An valid MAC address might have been provided by (uboot) firmware by
device-tree or in chip. It's reasonable to use it to maintain consistency.
This uses the MAC address from device-tree or that in the chip if it's
valid. Otherwise, a random MAC address is given as before.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Acked-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This introduces two helper functions to create or destroy MDIO
interface. No logical changes introduced except the proper MDIO
names are given when having more than one MDIO bus.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Acked-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the DSA driver function to configure the bridge ageing time.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
All Marvell switch chips from (88E6060 to 88E6390) have a ATU Control
register containing bits 11:4 to configure an ATU Age Time quotient.
However the coefficient used to calculate the ATU Age Time vary with the
models. E.g. 88E6060, 88E6352 and 88E6390 use respectively 16, 15 and
3.75 seconds.
Add a age_time_coeff to the info structure to handle this and a Global 1
helper to set the default age time of 5 minutes in the setup code.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add capability flags to describe the presence of Ingress Rate Limit unit
registers and an helper function to clear it.
In the meantime, fix a few harmless issues:
- 6185 and 6095 don't have such registers (reserved)
- the previous code didn't wait for the IRL operation to complete
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add flags and helpers to describe the presence of Priority Override
Table (POT) related registers and simplify the setup of Global 2.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add flags to describe the presence of Cross-chip Port VLAN Table (PVT)
related registers and simplify the setup of Global 2.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switches such as 88E6185 as 3 Switch MAC registers in Global 1. Newer
chips such as 88E6352 have freed these registers in favor of an indirect
access in a Switch MAC/WoL/WoF register in Global 2.
Explicit this difference with G1 and G2 helpers and flags.
Also, note that this indirect access is a single-register which doesn't
require to wait for the operation to complete (like Switch MAC, Trunk
Mapping, etc.), in contrary to multi-registers indirect accesses with
several operations and a busy bit.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some switches provide a Rsvd2CPU mechanism used to choose which of the
16 reserved multicast destination addresses matching 01:80:c2:00:00:0x
should be considered as MGMT and thus forwarded to the CPU port.
Other switches extend this mechanism to also configure as MGMT the
additional 16 reserved multicast addresses matching 01:80:c2:00:00:2x.
This mechanism is exposed via two registers in Global 2, and an Rsvd2CPU
enable bit in the management register.
Newer chip (such as 88E6390) has replaced these registers with a new
indirect MGMT mechanism in Global 1.
The patch adds two MV88E6XXX_FLAG_G2_MGMT_EN_{0,2}X flags to describe
the presence of these Global 2 registers. If 88E6390 support is added, a
MV88E6XXX_FLAG_G1_MGMT_CTRL flag will be needed to setup Rsvd2CPU.
Note: all switches still support in parallel the ATU Load operation with
an MGMT Entry State to forward such frames in a less convenient way.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Trunk Mask and Trunk Mapping registers are two Global 2 indirect
accesses to trunking configuration.
Add helpers for these tables and simplify the Global 2 setup.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Device Mapping register is an indirect table access.
Provide helpers to access this table and explicit the checking of the
new DSA_RTABLE_NONE routing table value.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Separate the setup of Global 1 and Global 2 internal SMI devices and add
a flag to describe the presence of this second registers set.
Also rearrange the G1 setup in the registers order.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
All 88E6xxx Marvell switches (even the old not supported yet 88E6060)
have at least an ATU, per-port STP states and VLAN map, to run basic
switch functions such as Spanning Tree and port based VLANs.
Get rid of the related MV88E6XXX_FLAG_{ATU,PORTSTATE,VLANTABLE} flags,
as they are defaults to every chip.
This enables STP on 6185 and removes many inconsistencies on others.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
VLAN and MQ control was doing DMA from the stack. Fix it.
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: "netdev@vger.kernel.org" <netdev@vger.kernel.org>
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
txr->dev_state was not consistently manipulated with the acquisition of
the per-queue lock, after further inspection the lock does not seem
necessary, either the value is read as BNXT_DEV_STATE_CLOSING or 0.
Reported-by: coverity (CID 1339583)
Fixes: c0c050c58d ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A bridge device in NS2 has the same device ID as the ethernet controller.
Add check to avoid probing the bridge device.
Signed-off-by: Prashant Sreedharan <prashant.sreedharan@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocate special vnic for dropping packets not matching the RX filters.
First vnic is for normal RX packets and the driver will drop all
packets on the 2nd vnic.
Signed-off-by: Prashant Sreedharan <prashant.sreedharan@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocate napi for special vnic, packets arriving on this
napi will simply be dropped and the buffers will be replenished back
to the HW.
Signed-off-by: Prashant Sreedharan <prashant.sreedharan@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hardware is unable to drop rx packets not matching the RX filters. To
workaround it, we create a special VNIC and configure the hardware to
direct all packets not matching the filters to it. We then setup the
driver to drop packets received on this VNIC.
This patch creates the infrastructure for this VNIC, reserves a
completion ring, and rx rings. Only shared completion ring mode is
supported. The next 2 patches add a NAPI to handle packets from this
VNIC and the setup of the VNIC.
Signed-off-by: Prashant Sreedharan <prashant.sreedharan@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
