The driver will be migrated to the RC driver API in a following
commit.
[mchehab@redhat.com: Fix some bad whitespacing]
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The imon devices have either 1 or 2 usb interfaces on them, each wired
up to its own urb callback. The interface 0 urb callback is wired up
before the imon context's rc_dev pointer is filled in, which is
necessary for imon 0xffdc device auto-detection to work properly, but we
need to make sure we don't actually run the callback routines until
we've entirely filled in the necessary bits for each given interface,
lest we wind up oopsing. Technically, any imon device could have hit
this, but the issue is exacerbated on the 0xffdc devices, which send a
constant stream of interrupts, even when they have no valid key data.
CC: Andy Walls <awalls@md.metrocast.net>
CC: Chris W <lkml@psychogeeks.com>
Reported-by: Chris W <lkml@psychogeeks.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* tag 'v3.1-rc6': (1902 commits)
Linux 3.1-rc6
ioctl: register LTTng ioctl
fuse: fix memory leak
fuse: fix flock breakage
Btrfs: add dummy extent if dst offset excceeds file end in
Btrfs: calc file extent num_bytes correctly in file clone
btrfs: xattr: fix attribute removal
Btrfs: fix wrong nbytes information of the inode
Btrfs: fix the file extent gap when doing direct IO
Btrfs: fix unclosed transaction handle in btrfs_cont_expand
Btrfs: fix misuse of trans block rsv
Btrfs: reset to appropriate block rsv after orphan operations
Btrfs: skip locking if searching the commit root in csum lookup
btrfs: fix warning in iput for bad-inode
Btrfs: fix an oops when deleting snapshots
[media] vp7045: fix buffer setup
[media] nuvoton-cir: simplify raw IR sample handling
[media] [Resend] viacam: Don't explode if pci_find_bus() returns NULL
[media] v4l2: Fix documentation of the codec device controls
[media] gspca - sonixj: Fix the darkness of sensor om6802 in 320x240
...
The nuvoton-cir driver was storing up consecutive pulse-pulse and
space-space samples internally, for no good reason, since
ir_raw_event_store_with_filter() already merges back to back like
samples types for us. This should also fix a regression introduced late
in 3.0 that related to a timeout change, which actually becomes correct
when coupled with this change. Tested with RC6 and RC5 on my own
nuvoton-cir hardware atop vanilla 3.0.0, after verifying quirky
behavior in 3.0 due to the timeout change.
Reported-by: Stephan Raue <sraue@openelec.tv>
CC: Stephan Raue <sraue@openelec.tv>
CC: stable@vger.kernel.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add pr_fmt.
Convert ene_warn and ene_notice to pr_<level>.
Use pr_debug in __dbg macro and a little neatening.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hi,
The following patch adds the IR code for the missing "OK" key to the Pinnacle
PCTV HD map. This map is now used by the PCTV 290e DVB-T2 device, whose remote
control has 26 buttons.
Signed-off-by: Chris Rankin <rankincj@yahoo.com>
Reviewed-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add note about recent updates coming from Microsoft's publicly available
specs on Windows Media Center remotes and receivers/transmitters.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Rather than dumping out hex values, lets print the actual calculated
frequency and period the hardware has been configured for. After this
[ 2643.276215] mceusb 3-1:1.0: tx data: 9f 07 (length=2)
[ 2643.276218] mceusb 3-1:1.0: Get carrier mode and freq
[ 2643.277206] mceusb 3-1:1.0: rx data: 9f 06 01 42 (length=4)
[ 2643.277209] mceusb 3-1:1.0: Got carrier of 37037 Hz (period 27us)
Matches up perfectly with the table in Microsoft's docs.
Of course, I've noticed on one of my devices that the MS-recommended
default value of 1 for carrier pre-scaler and 66 for carrier period was
butchered, and instead of converting 66 to hex (0x42 like above), they
put in 0x66, so the hardware reports a default carrier of 24390Hz.
Fortunately, I guess, this particular device is rx-only, but I wouldn't
put it past other hw to screw up here too.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
According to the specs, you can read the number of tx ports, number of
rx sensors, which tx ports have cables plugged into them, and which rx
sensors are active. In practice, most of my devices do seem to report
sane values for tx ports and rx sensors (but not all -- one without any
tx ports reports having them), and most report the active sensor
correctly, but only one of eight reports cabled tx ports correctly. So
for the most part, this is just for informational purposes.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Supposedly, there are essentially three different classes of devices
that are compatible with Microsoft's specs. First are the "legacy"
devices, which are built using Microsoft-provided hardware specs and
firmware. Second are "emulator" devices, which are built using custom
hardware and firmware, written to emulate Microsoft's firmware. Third
are "port" devices, which have their own device driver and firmware,
which provides compatible data to higher levels of the stack.
>From what I can tell, things like nuvoton-cir and fintek-cir are
essentially "port" devices -- their raw IR buffer format is very similar
to that of the mceusb devices. Now, within the mceusb driver, we have
three different "generations", which at first, seemed like maybe they
mapped to emulator versions. Unfortuantely, every single device I have
responds "illegal command" to the query to get firmware emulator version
from the hardware, which means they're either all emulator version 1, or
they're legacy devices, and our different "generations" aren't at all
related here. Though in theory, its possible the gen1 devices are
"legacy" devices and the rest are emulator v1. There are some useful
features of the v2 interface I was hoping to play with, but alas...
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
According to MS docs, the device firmware may halt after receiving an
unknown instruction, but that it should be possible to tell the firmware
to continue running by simply sending a device resume command. So lets
do that.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Its not uncommon for folks to force these bits enabled, because people
do want to wake their htpc kit via their remote. Lets just set the bits
for 'em.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Sometimes the init routine is blasting commands out to the hardware
faster than it can reply. Throw a brief delay in there to give the
hardware a chance to reply before we send the next command.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
I was recently pointed to the document titled
Windows-Media-Center-RC-IR-Collection-Green-Button-Specification-03-08-2011-V2.pdf
which as of this writing, is publicly available from
download.microsoft.com. It covers a LOT of the gaps in the mceusb
driver, which to this point, was written almost entirely by
reverse-engineering. First up, I'm updating the defines for all the MCE
commands and responses to match their names in the spec. More to come...
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are folks with flaky imon hardware out there that doesn't always
respond to requests to write to their displays for some reason, which
can flood logs quickly when something like lcdproc is trying to
constantly update the display, so lets rate-limit all that error spew.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
rc unregister logic were deadly broken, preventing some drivers to
be removed. Among the broken things, rc_dev_uevent() is being called
during device_del(), causing a data filling on an area that it is
not ready anymore.
Also, some drivers have a stop callback defined, that needs to be called
before data removal, as it stops data polling.
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (430 commits)
[media] ir-mce_kbd-decoder: include module.h for its facilities
[media] ov5642: include module.h for its facilities
[media] em28xx: Fix DVB-C maxsize for em2884
[media] tda18271c2dd: Fix saw filter configuration for DVB-C @6MHz
[media] v4l: mt9v032: Fix Bayer pattern
[media] V4L: mt9m111: rewrite set_pixfmt
[media] V4L: mt9m111: fix missing return value check mt9m111_reg_clear
[media] V4L: initial driver for ov5642 CMOS sensor
[media] V4L: sh_mobile_ceu_camera: fix Oops when USERPTR mapping fails
[media] V4L: soc-camera: remove soc-camera bus and devices on it
[media] V4L: soc-camera: un-export the soc-camera bus
[media] V4L: sh_mobile_csi2: switch away from using the soc-camera bus notifier
[media] V4L: add media bus configuration subdev operations
[media] V4L: soc-camera: group struct field initialisations together
[media] V4L: soc-camera: remove now unused soc-camera specific PM hooks
[media] V4L: pxa-camera: switch to using standard PM hooks
[media] NetUP Dual DVB-T/C CI RF: force card hardware revision by module param
[media] Don't OOPS if videobuf_dvb_get_frontend return NULL
[media] NetUP Dual DVB-T/C CI RF: load firmware according card revision
[media] omap3isp: Support configurable HS/VS polarities
...
Fix up conflicts:
- arch/arm/mach-omap2/board-rx51-peripherals.c:
cleanup regulator supply definitions in mach-omap2
vs
OMAP3: RX-51: define vdds_csib regulator supply
- drivers/staging/tm6000/tm6000-alsa.c (trivial)
drivers/media/rc/ir-mce_kbd-decoder.c:446:16: error: expected declaration specifiers or '...' before string constant
drivers/media/rc/ir-mce_kbd-decoder.c:446:1: warning: data definition has no type or storage class
drivers/media/rc/ir-mce_kbd-decoder.c:446:1: warning: type defaults to 'int' in declaration of 'MODULE_LICENSE'
drivers/media/rc/ir-mce_kbd-decoder.c:446:16: warning: function declaration isn't a prototype
drivers/media/rc/ir-mce_kbd-decoder.c:447:15: error: expected declaration specifiers or '...' before string constant
drivers/media/rc/ir-mce_kbd-decoder.c:447:1: warning: data definition has no type or storage class
drivers/media/rc/ir-mce_kbd-decoder.c:447:1: warning: type defaults to 'int' in declaration of 'MODULE_AUTHOR'
drivers/media/rc/ir-mce_kbd-decoder.c:447:15: warning: function declaration isn't a prototype
drivers/media/rc/ir-mce_kbd-decoder.c:448:20: error: expected declaration specifiers or '...' before string constant
drivers/media/rc/ir-mce_kbd-decoder.c:448:1: warning: data definition has no type or storage class
drivers/media/rc/ir-mce_kbd-decoder.c:448:1: warning: type defaults to 'int' in declaration of 'MODULE_DESCRIPTION'
drivers/media/rc/ir-mce_kbd-decoder.c:448:20: warning: function declaration isn't a prototype
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is admittedly a bit of a hack, but if we change our timeout value
to something longer and fudge our synthesized trailing space sample
based on the initial pulse sample, rc-core decode continues to work just
fine with both rc-6 and rc-5, and now lirc userspace decode shows proper
repeats for both of those protocols as well. Also tested NEC
successfully with both decode options.
We do still need a reset timer callback using the hardware's timeout
value to make sure we actually process samples correctly, regardless of
our somewhat hacky timeout and synthesized trailer above.
This also adds a missing del_timer_sync call to the module unload path.
CC: Chris Dodge <chris@redrat.co.uk>
CC: Andrew Vincer <andrew.vincer@redrat.co.uk>
CC: Stephen Cox <scox_nz@yahoo.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Trying to cap duration before multiplying it was obviously wrong.
CC: Chris Dodge <chris@redrat.co.uk>
CC: Andrew Vincer <andrew.vincer@redrat.co.uk>
CC: Stephen Cox <scox_nz@yahoo.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We already add a trailing space, this wasn't doing anything useful, and
actually confused lirc userspace a bit. Rip it out.
CC: Chris Dodge <chris@redrat.co.uk>
CC: Andrew Vincer <andrew.vincer@redrat.co.uk>
CC: Stephen Cox <scox_nz@yahoo.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is a custom IR protocol decoder, for the RC-6-ish protocol used by
the Microsoft Remote Keyboard, apparently developed internally at
Microsoft, and officially dubbed MCIR-2, per their March 2011 remote and
transceiver requirements and specifications document, which also touches
on this IR keyboard/mouse device.
Its a standard keyboard with embedded thumb stick mouse pointer and
mouse buttons, along with a number of media keys. The media keys are
standard RC-6, identical to the signals from the stock MCE remotes, and
will be handled as such. The keyboard and mouse signals will be decoded
and delivered to the system by an input device registered specifically
by this driver.
Successfully tested with multiple mceusb-driven transceivers, as well as
with fintek-cir and redrat3 hardware. Essentially, any raw IR hardware
with enough sampling resolution should be able to use this decoder,
nothing about it is at all receiver-hardware-specific.
This work is inspired by lirc_mod_mce:
The documentation there and code aided in understanding and decoding the
protocol, but the bulk of the code is actually borrowed more from the
existing in-kernel decoders than anything. I did recycle the keyboard
keycode table, a few defines, and some of the keyboard and mouse data
parsing bits from lirc_mod_mce though.
Special thanks to James Meyer for providing the hardware, and being
patient with me as I took forever to get around to writing this.
callback routine to ensure we don't get any stuck keys, and used
symbolic names for the keytable. Also cc'ing Florian this time, who I
believe is the original mod-mce author...
CC: Florian Demski <fdemski@users.sourceforge.net>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Microsoft's Windows Media Center specification and requirements doc from
2011.03.18 now refers to the former Power Toggle button as the Sleep
Toggle, and recommends using a new moon sleep icon for it. Its the same
key, but its apparently always been meant to put the system to sleep,
not power it off. Adjust accordingly. While we're here, lets also remove
the duplicate KEY_PLAYPAUSE entry.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Durations can never be negative, so it makes sense to consistently use
unsigned int for LIRC transmission. Contrary to the initial impression,
this shouldn't actually change the userspace API.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The conversion of winbond-cir to use rc-core seems to have missed a
a few bits and pieces which were in my local tree. Kudos to
Juan Jesús García de Soria Lucena <skandalfo@gmail.com> for noticing.
[mchehab@redhat.com: fix two UTF-8 violations]
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In the original code, if the allocation failed we dereference "rr3"
when it was NULL.
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If change_protocol() fails and we goto out_raw, then it calls unlock
twice. I noticed that the other time we called change_protocol() we
held the &dev->lock, so I changed it to hold it here too.
Reviewed-by: Jarod Wilson <jarod@redhat.com>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (43 commits)
fs: Merge split strings
treewide: fix potentially dangerous trailing ';' in #defined values/expressions
uwb: Fix misspelling of neighbourhood in comment
net, netfilter: Remove redundant goto in ebt_ulog_packet
trivial: don't touch files that are removed in the staging tree
lib/vsprintf: replace link to Draft by final RFC number
doc: Kconfig: `to be' -> `be'
doc: Kconfig: Typo: square -> squared
doc: Konfig: Documentation/power/{pm => apm-acpi}.txt
drivers/net: static should be at beginning of declaration
drivers/media: static should be at beginning of declaration
drivers/i2c: static should be at beginning of declaration
XTENSA: static should be at beginning of declaration
SH: static should be at beginning of declaration
MIPS: static should be at beginning of declaration
ARM: static should be at beginning of declaration
rcu: treewide: Do not use rcu_read_lock_held when calling rcu_dereference_check
Update my e-mail address
PCIe ASPM: forcedly -> forcibly
gma500: push through device driver tree
...
Fix up trivial conflicts:
- arch/arm/mach-ep93xx/dma-m2p.c (deleted)
- drivers/gpio/gpio-ep93xx.c (renamed and context nearby)
- drivers/net/r8169.c (just context changes)
The nuvoton-cir inherited an insanely low idle timeout value from the
mceusb driver. We're fixing mceusb, should fix this driver too.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This matches the typical timeout advertised by hardware, once we're
actually interpreting it correctly.
Signed-off-by: Rafi Rubin <rafi@seas.upenn.edu>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Unit missmatch in mceusb_handle_command. It should be converting to us,
not 1/10th of ms.
mceusb_dev_printdata 100us/ms -> 1000us/ms
Alter format of fix slightly and update comment to match proper reality.
Signed-off-by: Rafi Rubin <rafi@seas.upenn.edu>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Due to commit cdda911c34, evdev only
becomes readable when the buffer contains an EV_SYN/SYN_REPORT event. If
we get a repeat or a scancode we don't have a mapping for, we never call
input_sync, and thus those events don't get reported in a timely
fashion.
For example, take an mceusb transceiver with a default rc6 keymap. Press
buttons on an rc5 remote while monitoring with ir-keytable, and you'll
see nothing. Now press a button on the rc6 remote matching the keymap.
You'll suddenly get the rc5 key scancodes, the rc6 scancode and the rc6
key spit out all at the same time.
Pressing and holding a button on a remote we do have a keymap for also
works rather unreliably right now, due to repeat events also happening
without a call to input_sync (we bail from ir_do_keydown before getting
to the point where it calls input_sync).
Easy fix though, just add two strategically placed input_sync calls
right after our input_event calls for EV_MSC, and all is well again.
Technically, we probably should have been doing this all along, its just
that it never caused any functional difference until the referenced
change went into the input layer.
input_sync once per IR signal. There was another hidden bug in the code
where we were calling input_report_key using last_keycode instead of our
just discovered keycode, which manifested with the reordering of calling
input_report_key and setting last_keycode.
Reported-by: Stephan Raue <sraue@openelec.tv>
CC: Stephan Raue <sraue@openelec.tv>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
CC: Jeff Brown <jeffbrown@android.com>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
While 0xffdc devices have their IR protocol hard-coded into the firmware
of the device, we have no known way of telling what it is if we don't
have the device's config byte already in the driver. Unknown devices
default to the imon native protocol, but might actually be rc6, so we
should set the driver up such that the user can load the rc6 keytable
from userspace and still have a working device ahead of its config byte
being added to the driver.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Another device with the 0xffdc device id, this one with 0x7e in the
config byte. Its an iMON VFD + RC6 IR, in a CoolerMaster 260 case.
Reported-by: Filip Streibl <filip@streibl.cz>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With hardware that has to use ir_raw_event_store_edge to collect IR
sample durations, we were not doing an event reset unless
IR_MAX_DURATION had passed. That's around 4 seconds. So if someone
presses up, then down, with less than 4 seconds in between, they'd get
the initial up, then up and down upon pressing down.
To fix this, I've lowered the "send a reset event" logic's threshold to
the input device's REP_DELAY (defaults to 500ms), and with an
saa7134-based GPIO-driven IR receiver in a Hauppauge HVR-1150, I get
*much* better behavior out of the remote now. Special thanks to Devin
for providing the hardware to investigate this issue.
CC: stable@kernel.org
CC: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Both consumers of RC_MAP_PINNACLE_PCTV_HD send along full RC-5
scancodes, so this update makes this keymap actually *have* full
scancodes, heisted from rc-dib0700-rc5.c. This should fix out of the box
remote functionality for the Pinnacle PCTV HD 800i (cx88 pci card) and
PCTV HD Pro 801e (em28xx usb stick).
CC: stable@kernel.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Thanks to the intrepid testing and debugging of Matthijs van Drunen, it
was uncovered that at least some variants of the ITE8709 need to use pnp
resource 2, rather than 0, for things to function properly. Resource 0
has a length of only 1, and if you try to bypass the pnp_port_len check
and use it anyway (with either a length of 1 or 2), the system in
question's trackpad ceased to function.
The circa lirc 0.8.7 lirc_ite8709 driver used resource 2, but the value
was (amusingly) changed to 0 by way of a patch from ITE themselves, so I
don't know if there may be variants where 0 actually *is* correct, but
at least in this case and in the original lirc_ite8709 driver author's
case, it sure looks like 2 is the right value.
This fix should probably be applied to all stable kernels with the
ite-cir driver, lest we nuke more people's trackpads.
Tested-by: Matthijs van Drunen
CC: Juan Jesús García de Soria <skandalfo@gmail.com>
CC: stable@kernel.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Many stupid corrections of duplicated includes based on the output of
scripts/checkincludes.pl.
Signed-off-by: Vitaliy Ivanov <vitalivanov@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
As pointed out on the lirc list by Andreas Dick, initial panel key
repeat suppression wasn't working, as we had no timevals accumulated
until after the first repeat. Also add a missing locking call.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Courtesy of information from Andreas Dick on the lirc list.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Petter Selasky pointed out to me that we're leaking urbs when
mce_async_out is called. Its used both for configuring the hardware and
for transmitting IR data. In the tx case, mce_request_packet actually
allocates both a urb and the transfer buffer, neither of which was being
torn down. Do that in the tx callback.
CC: Hans Petter Selasky <hselasky@c2i.net>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There was a missing lock in fintek_suspend. Without the lock, its
possible the system will be in the middle of receiving IR (draining the
RX buffer) when we try to disable CIR interrupts.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Store the cdev pointer in struct irctl, allocated dynamically as needed,
rather than having a static array. At the same time, recycle some of the
saved memory to nudge the maximum number of lirc devices supported up a
ways -- its not that uncommon these days, now that we have the rc-core
lirc bridge driver, to see a system with at least 4 raw IR receivers.
(consider a mythtv backend with several video capture devices and the
possible need for IR transmit hardware).
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Aside from the initial "hey, lets make sure we've flushed any
pre-existing data on the device" call to mce_sync_in, every other one of
the calls was entirely superfluous. Ergo, remove them all, and rename
the one and only (questionably) useful one to reflect what it really
does. Verified on both gen2 and gen3 hardware to make zero difference.
Well, except that you no longer get a bunch of urb submit failures from
the unneeded mce_sync_in calls. Oh. And move that flush to a point
*after* we've wired up the inbound urb, or it won't do squat. I have
half a mind to just remove it entirely, but someone thought it was
necessary at some point, and it doesn't seem to hurt, so lets leave it
for the time being.
This excercise took place due to insightful questions asked by Hans
Petter Selasky, about the possible reuse of the inbound urb before it
was actually availble by mce_sync_in, so thanks to him for motivating
this cleanup.
Reported-by: Hans Petter Selasky <hselasky@c2i.net>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There's an SMK-device-id remote kit from I-O Data avaiable primarily in
Japan, which appears to have no tx hardware, but has rx functionality
that works with the mceusb driver by simply adding its device ID.
Reported-by: Jeremy Kwok <jeremykwok@desu.ca>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Using dev_dbg is more complexity than many users are able to deal with.
Make it easier to get debug spew feedback from them by adding an mce_dbg
printk macro that spews using dev_info when debug=1 is set for the
mceusb module.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
driver to use dvb-usb-remote.
The remote(s) generates 24 bit NEC codes, lme2510 keymaps redefined.
Other minor fixes
fix le warning.
make sure frontend is detached on firmware change.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is a new driver for the Fintek LPC SuperIO CIR function, in the
Fintek F71809 chip. Hardware and datasheets were provided by Fintek, so
thanks go to them for supporting this effort.
This driver started out as a copy of the nuvoton-cir driver, and was
then modified as needed for the Fintek chip. The two share many
similaries, though the buffer handling for the Fintek chip is actually
nearly identical to the mceusb buffer handling, so the parser routine is
almost a drop-in copy of the mceusb buffer parser (a candidate for being
abstracted out into shared code at some point).
This initial code drop *only* supports receive, but the hardware does
support transmit as well. I really haven't even started to look at
what's required, but my guess is that its also pretty similar to mceusb.
Most people are probably only really interested in RX anyway though, so
I think its good to get this out there even with only RX.
(Nb: there are also Fintek-made mceusb receivers, which presumably, this
chip shares CIR hardware with).
This hardware can be found on at least Jetway NC98 boards and derivative
systems, and likely others as well. Functionality was tested with an
NC98 development board, in-kernel decode of RC6 (mce), RC5 (hauppauge)
and NEC-ish (tivo) remotes all successful, as was lirc userspace decode
of the RC6 remote.
CC: Aaron Huang <aaron_huang@fintek.com.tw>
CC: Tom Tsai <tom_tsai@fintek.com.tw>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The default REP_PERIOD is 33 ms. This doesn't make sense for IR's,
as, in general, an IR repeat scancode is provided at every 110/115ms,
depending on the RC protocol. So, increase its default, to do a
better job avoiding ghost repeat events.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Jarod Wilson <jarod@redhat.com>
ictx->touch is intialied in imon_init_intf1, to the result of calling the
function that contains this code. Thus, in this code, input_free_device
should be called on touch itself.
A simplified version of the semantic match that finds this problem is:
(http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
local idexpression struct input_dev * x;
expression ra,rr;
position p1,p2;
@@
x = input_allocate_device@p1(...)
... when != x = rr
when != input_free_device(x,...)
when != if (...) { ... input_free_device(x,...) ...}
if(...) { ... when != x = ra
when forall
when != input_free_device(x,...)
\(return <+...x...+>; \| return@p2...; \) }
@script:python@
p1 << r.p1;
p2 << r.p2;
@@
cocci.print_main("input_allocate_device",p1)
cocci.print_secs("input_free_device",p2)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is a new rc-core device driver for the IR transceivers made by
RedRat Ltd. (http://redrat.co.uk/). It started out life as an
out-of-lirc-tree lirc driver, maintained in its own repo on sourceforge,
by Stephen Cox. He started porting it to what was then ir-core, and I
finally picked it up about two week ago and did a fairly large overhaul
on it, and its now into a state where I'm fairly comfortable submitting
it here for review and inclusion in the kernel. I'm claiming authorship
of this driver, since while it started out as Stephen's work, its
definitely a derivative work now, at 876 lines added and 1698 lines
removed since grabbing it from sourceforge. Stephen's name is retained
as secondary author though, and credited in the headers. Those
interested in seeing how the changes evolved can (at least for now) look
at this branch in my git tree:
http://git.kernel.org/?p=linux/kernel/git/jarod/linux-2.6-ir.git;a=shortlog;h=refs/heads/redrat3
That won't be around forever though, and I'm doing this as a single
commit to go into mainline. Anyway...
I've successfully tested in-kernel decode of rc5, rc6 and nec remotes,
as well as lirc userspace decode of rc5 and rc6. There are still some
quirks here to sort out with rc5 lirc userspace decode, but I'm working
with the RedRat folks themselves to figure out what's going on there
(rc5 lirc decode works, but you only get an event on key release --
in-kernel rc5 decode behaves perfectly fine). Note that lirc decode of
rc6 is working perfectly. Transmit is also working, tested by pointing
the redrat3 at an mceusb transceiver, which happily picked up the
transmitted signals and properly decoded them.
There's no default remote for this hardware, so its somewhat arbitrarily
set to use the Hauppauge RC5 keymap by default. Easily changed out by
way of ir-keytable and irrelevant if you're using lircd for decode.
CC: Chris Dodge <chris@redrat.co.uk>
CC: Andrew Vincer <Andrew.Vincer@redrat.co.uk>
CC: Stephen Cox <scox_nz@yahoo.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Continuing with IR transmit after resuming from suspend seems fairly
useless, given that the only place we can actually end up suspending is
after IR has been send and we're simply mdelay'ing. Lets simplify the
resume path by just waiting on tx to complete in the suspend path, then
we know we can't be transmitting on resume, and reinitialization of the
hardware registers becomes more straight-forward.
CC: Juan Jesús García de Soria <skandalfo@gmail.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There was some rather odd spacing in a few of the ite8709-specific
functions that made it hard to read those sections of code. This is just
a simple reformatting.
CC: Juan Jesús García de Soria <skandalfo@gmail.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Just recently acquired an Asus Eee Box PC with an onboard IR receiver
driven by ite-cir (ITE8713 sub-variant). Works out of the box with the
ite-cir driver in 2.6.39, but stops working after a suspend/resume
cycle. Its fixed by simply reinitializing registers after resume,
similar to what's done in the nuvoton-cir driver. I've not tested with
any other ITE variant, but code inspection suggests this should be safe
on all variants.
Reported-by: Stephan Raue <sraue@openelec.tv>
CC: Juan Jesús García de Soria <skandalfo@gmail.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- Eliminate a possible circular locking lockdep warning
- Make sure we don't try to unregister a vfd on a device w/a vga screen
- Always free imon context after devices are removed (display_close can
just error out w/no context)
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- Set a default timeout (matching mceusb.c) and use
ir_raw_event_store_with_filter, which leads to better behavior when
using lirc userspace decoding with this hardware
- Fill in rx_resolution with the value we're using here (50us)
- Wire up input phys and device parent pointer
- Use device_init_wakeup() instead of device_set_wakeup_*()
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Using ir_raw_event_store_with_filter() saves about 20 lines of code.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If an IR command is sent (using the LIRC userspace) to rc-loopback
which doesn't include a trailing space, the result is that the message
won't be completely decoded. In addition, "leftovers" from a previous
transmission can be left until the next one. Fix this by faking a long
silence after the end of TX data.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds preliminary IR TX capabilities to the
winbond-cir driver.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Using bool instead of an int helps readability a bit.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Per hardware provided to me, the Formosa Industrial Computing eHome
Infrared Receiver, 0x147a:0xe017, has no tx capability, it is rx only.
Thanks go to Paul Rae for the hardware.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Thanks to some excellent investigative work by Douglas Clowes, it was
uncovered that the older w83667hg Nuvoton chip functions with this
driver after actually enabling the CIR function via its multi-function
chip config register. The CIR and CIR wide-band sensor enable bits are
just in a different place on this hardware, so we only poke register
0x27 on 677 hardware now, and we poke register 0x2c on the 667 now.
Reported-by: Douglas Clowes <dclowes1@optusnet.com.au>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are additional chip IDs that report a PNP ID of NTN0530, which we
were refusing to load on. Instead, lets just warn if we encounter an
unknown chip, as there's a chance it will work just fine.
Also, expand the list of known hardware to include both an earlier and a
later generation chip that this driver should function with. Douglas has
an older w83667hg variant, that with a touch more work, will be
supported by this driver, and Lutz has a newer w83677hg variant that
works without any further modifications to the driver.
Reported-by: Douglas Clowes <dclowes1@optusnet.com.au>
Reported-by: Lutz Sammer <johns98@gmx.net>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use the newly introduced KEY_IMAGES where appropriate, and standardize
on KEY_MEDIA for media center/application launcher button (such as the
Windows logo key on the Windows Media Center Ed. remotes).
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
[media] ngene: Fix CI data transfer regression Fix CI data transfer regression introduced by previous cleanup.
[media] v4l: make sure drivers supply a zeroed struct v4l2_subdev
[media] Missing frontend config for LME DM04/QQBOX
[media] rc_core: avoid kernel oops when rmmod saa7134
[media] imon: add conditional locking in change_protocol
[media] rc: show RC_TYPE_OTHER in sysfs
[media] ite-cir: modular build on ppc requires delay.h include
[media] mceusb: add Dell transceiver ID
The following is a patch to avoid a kernel oops when running rmmod
saa7134 on kernel 2.6.27.1. The change is as suggested by mchehab on
irc.freenode.org
Signed-off-by: Hussam Al-Tayeb <ht990332@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The imon_ir_change_protocol function gets called two different ways, one
way is from rc_register_device, for initial protocol selection/setup,
and the other is via a userspace-initiated protocol change request,
either by direct sysfs prodding or by something like ir-keytable.
In the rc_register_device case, the imon context lock is already held,
but when initiated from userspace, it is not, so we must acquire it,
prior to calling send_packet, which requires that the lock is held.
Without this change, there's an easily reproduceable deadlock when
another function calls send_packet (such as either of the display write
fops) after a userspace-initiated change_protocol.
With a lock-debugging-enabled kernel, I was getting this:
[ 15.014153] =====================================
[ 15.015048] [ BUG: bad unlock balance detected! ]
[ 15.015048] -------------------------------------
[ 15.015048] ir-keytable/773 is trying to release lock (&ictx->lock) at:
[ 15.015048] [<ffffffff814c6297>] mutex_unlock+0xe/0x10
[ 15.015048] but there are no more locks to release!
[ 15.015048]
[ 15.015048] other info that might help us debug this:
[ 15.015048] 2 locks held by ir-keytable/773:
[ 15.015048] #0: (&buffer->mutex){+.+.+.}, at: [<ffffffff8119d400>] sysfs_write_file+0x3c/0x144
[ 15.015048] #1: (s_active#87){.+.+.+}, at: [<ffffffff8119d4ab>] sysfs_write_file+0xe7/0x144
[ 15.015048]
[ 15.015048] stack backtrace:
[ 15.015048] Pid: 773, comm: ir-keytable Not tainted 2.6.38.4-20.fc15.x86_64.debug #1
[ 15.015048] Call Trace:
[ 15.015048] [<ffffffff81089715>] ? print_unlock_inbalance_bug+0xca/0xd5
[ 15.015048] [<ffffffff8108b35c>] ? lock_release_non_nested+0xc1/0x263
[ 15.015048] [<ffffffff814c6297>] ? mutex_unlock+0xe/0x10
[ 15.015048] [<ffffffff814c6297>] ? mutex_unlock+0xe/0x10
[ 15.015048] [<ffffffff8108b67b>] ? lock_release+0x17d/0x1a4
[ 15.015048] [<ffffffff814c6229>] ? __mutex_unlock_slowpath+0xc5/0x125
[ 15.015048] [<ffffffff814c6297>] ? mutex_unlock+0xe/0x10
[ 15.015048] [<ffffffffa02964b6>] ? send_packet+0x1c9/0x264 [imon]
[ 15.015048] [<ffffffff8108b376>] ? lock_release_non_nested+0xdb/0x263
[ 15.015048] [<ffffffffa0296731>] ? imon_ir_change_protocol+0x126/0x15e [imon]
[ 15.015048] [<ffffffffa024a334>] ? store_protocols+0x1c3/0x286 [rc_core]
[ 15.015048] [<ffffffff81326e4e>] ? dev_attr_store+0x20/0x22
[ 15.015048] [<ffffffff8119d4cc>] ? sysfs_write_file+0x108/0x144
...
The original report that led to the investigation was the following:
[ 1679.457305] INFO: task LCDd:8460 blocked for more than 120 seconds.
[ 1679.457307] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 1679.457309] LCDd D ffff88010fcd89c8 0 8460 1 0x00000000
[ 1679.457312] ffff8800d5a03b48 0000000000000082 0000000000000000 ffff8800d5a03fd8
[ 1679.457314] 00000000012dcd30 fffffffffffffffd ffff8800d5a03fd8 ffff88010fcd86f0
[ 1679.457316] ffff8800d5a03fd8 ffff8800d5a03fd8 ffff88010fcd89d0 ffff8800d5a03fd8
[ 1679.457319] Call Trace:
[ 1679.457324] [<ffffffff810ff1a5>] ? zone_statistics+0x75/0x90
[ 1679.457327] [<ffffffff810ea907>] ? get_page_from_freelist+0x3c7/0x820
[ 1679.457330] [<ffffffff813b0a49>] __mutex_lock_slowpath+0x139/0x320
[ 1679.457335] [<ffffffff813b0c41>] mutex_lock+0x11/0x30
[ 1679.457338] [<ffffffffa0d54216>] display_open+0x66/0x130 [imon]
[ 1679.457345] [<ffffffffa01d06c0>] usb_open+0x180/0x310 [usbcore]
[ 1679.457349] [<ffffffff81143b3b>] chrdev_open+0x1bb/0x2d0
[ 1679.457350] [<ffffffff8113d93d>] __dentry_open+0x10d/0x370
[ 1679.457352] [<ffffffff81143980>] ? chrdev_open+0x0/0x2d0
...
Bump the driver version here so its easier to tell if people have this
locking fix or not, and also make locking during probe easier to follow.
CC: stable@kernel.org
Reported-by: Benjamin Hodgetts <ben@xnode.org>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Stop including <linux/delay.h> in x86 header files which don't
need it. This will let the compiler complain when this header is
not included by source files when it should, so that
contributors can fix the problem before building on other
architectures starts to fail.
Credits go to Geert for the idea.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: James E.J. Bottomley <James.Bottomley@suse.de>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
LKML-Reference: <20110325152014.297890ec@endymion.delvare>
[ this also fixes an upstream build bug in drivers/media/rc/ite-cir.c ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Fix the following compile failure:
drivers/media/rc/ite-cir.c: In function 'ite_decode_bytes':
drivers/media/rc/ite-cir.c:190: error: implicit declaration of function 'generic_find_next_le_bit'
drivers/media/rc/ite-cir.c:199: error: implicit declaration of function 'generic_find_next_zero_le_bit'
Caused by commit 620a32bba4 ("[media] rc: New rc-based ite-cir driver
for several ITE CIRs") interacting with commit c4945b9ed4
("asm-generic: rename generic little-endian bitops functions").
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (442 commits)
[media] videobuf2-dma-contig: make cookie() return a pointer to dma_addr_t
[media] sh_mobile_ceu_camera: Do not call vb2's mem_ops directly
[media] V4L: soc-camera: explicitly require V4L2_BUF_TYPE_VIDEO_CAPTURE
[media] v4l: soc-camera: Store negotiated buffer settings
[media] rc: interim support for 32-bit NEC-ish scancodes
[media] mceusb: topseed 0x0011 needs gen3 init for tx to work
[media] lirc_zilog: error out if buffer read bytes != chunk size
[media] lirc: silence some compile warnings
[media] hdpvr: use same polling interval as other OS
[media] ir-kbd-i2c: pass device code w/key in hauppauge case
[media] rc/keymaps: Remove the obsolete rc-rc5-tv keymap
[media] remove the old RC_MAP_HAUPPAUGE_NEW RC map
[media] rc/keymaps: Rename Hauppauge table as rc-hauppauge
[media] rc-rc5-hauppauge-new: Fix Hauppauge Grey mapping
[media] rc-rc5-hauppauge-new: Add support for the old Black RC
[media] rc-rc5-hauppauge-new: Add the old control to the table
[media] rc-winfast: Fix the keycode tables
[media] a800: Fix a few wrong IR key assignments
[media] opera1: Use multimedia keys instead of an app-specific mapping
[media] dw2102: Use multimedia keys instead of an app-specific mapping
...
Fix up trivial conflicts (remove/modify and some real conflicts) in:
arch/arm/mach-omap2/devices.c
drivers/staging/Kconfig
drivers/staging/Makefile
drivers/staging/dabusb/dabusb.c
drivers/staging/dabusb/dabusb.h
drivers/staging/easycap/easycap_ioctl.c
drivers/staging/usbvideo/usbvideo.c
drivers/staging/usbvideo/vicam.c
The Apple and TiVo remotes I've got use an NEC-ish protocol, but rather
than a command/not_command pair, they have what appear to be vendor ID
bytes. This change makes the NEC decoder warn if the command/not_command
checksum fails, but then passes along a full 32-bit scancode for keymap
lookup. This change should make no difference for existing keymaps,
since they simply won't have 32-bit scancodes, but allows for a 32-bit
keymap. At the moment, that'll have to be uploaded by the user, but I've
got Apple and TiVo remote keymaps forthcoming.
In the long run (2.6.40, hopefully), we should probably just always use
all 32 bits for all NEC keymaps, but this should get us by for 2.6.39.
(Note that a few of the TiVo keys actuallly *do* pass the command
checksum, so for now, the keymap for this remote will have to be a mix
of 24-bit and 32-bit scancodes, but so be it).
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This keymap were used for the Hauppauge Black remote controller
only. It also contains some keycodes not found there. As the
Hauppauge Black is now part of the hauppauge keymap, just remove
it.
Also, remove the modprobe hacks to select between the Gray
and the Black versions of the remote controller as:
- Both are supported by default by the keymap;
- If the user just wants one keyboard supported,
it is just a matter of changing the keymap via
the userspace tool (ir-keytable), removing
the keys that he doesn't desire. As ir-keytable
auto-loads the keys via udev, this is better than
obscure modprobe parameters.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
The rc-hauppauge-new map is a messy thing, as it bundles 3
different remote controllers as if they were just one,
discarding the address byte. Also, some key maps are wrong.
With the conversion to the new rc-core, it is likely that
most of the devices won't be working properly, as the i2c
driver and the raw decoders are now providing 16 bits for
the remote, instead of just 8.
delete mode 100644 drivers/media/rc/keymaps/rc-hauppauge-new.c
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
There are two "hauppauge-new" keymaps, one with protocol
unknown, and the other with the protocol marked accordingly.
However, both tables are miss-named.
Also, the old rc-hauppauge-new is broken, as it mixes
three different controllers as if they were just one.
This patch solves half of the problem by renaming the
correct keycode table as just rc-hauppauge. This table
contains the codes for the four different types of
remote controllers found on Hauppauge cards, properly
mapped with their different addresses.
create mode 100644 drivers/media/rc/keymaps/rc-hauppauge.c
delete mode 100644 drivers/media/rc/keymaps/rc-rc5-hauppauge-new.c
[Jarod: fix up RC_MAP_HAUPPAUGE defines]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
The keys for the old black were messed with the ones for the
hauppauge grey. Fix it.
Also, fixes some keycodes and order the keys according with
the way they appear inside the remote controller.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Hans borrowed me an old Black Hauppauge RC. Thanks to that, we
can fix the RC5 table for Hauppauge.
Thanks-to: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Adds the old grey remote controller to Hauppauge table.
Hans borrowed me an old gray Hauppauge RC. Thanks to that, we
can fix the RC5 table for Hauppauge.
Thanks-to: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
One of the remotes has a picture available at:
http://lirc.sourceforge.net/remotes/leadtek/Y04G0004.jpg
As there's one variant with a set direction keys plus vol/chann
keys, and the same table is used for both models, change it to
represent all keys, avoiding the usage of weird function keys.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Using xev and testing the "Windows" key on a normal keyboard, it
is mapped as KEY_LEFTMETA. So, as this is the standard code for
it, use it, instead of a generic, meaningless KEY_PROG1.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Those KEY_PROG[n] keys were used on places where the developer
didn't know for sure what key should be used. On several cases,
using KEY_RED, KEY_GREEN, KEY_YELLOW would be enough. On others,
there are specific keys for that already.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Each keyboard map were using a different definition for
the Source/Video Source key.
Behold Columbus were the only one using KEY_PROPS.
As we want to standardize those keys at X11 and at
userspace applications, we need to use just one code
for it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
On a few places, KEY_MHP were used for snapshots. However, KEY_CAMERA
is used for it on all the other keyboards that have a snapshot/Picture
button.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Cc: Juan J. Garcia de Soria <skandalfo@gmail.com>
Cc: Stephan Raue <stephan@openelec.tv>
Cc: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
